Wiper & Washer: Section

DRIVER CONTROLS
SECTION
WIPER & WASHER
WW B
E
CONTENTS
BASIC INSPECTION .................................... 3 POWER SUPPLY AND GROUND CIRCUIT .... 23 F
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 BCM (BODY CONTROL MODULE) ..........................23
Work Flow ................................................................. 3 BCM (BODY CONTROL MODULE) : Diagnosis
G
Procedure ................................................................23
SYSTEM DESCRIPTION .............................. 5
IPDM E/R (INTELLIGENT POWER DISTRIBU-
FRONT WIPER AND WASHER SYSTEM .......... 5 TION MODULE ENGINE ROOM) ..............................23 H
IPDM E/R (INTELLIGENT POWER DISTRIBU-
WITH RAIN SENSOR .................................................. 5 TION MODULE ENGINE ROOM) : Diagnosis Pro-
WITH RAIN SENSOR : System Diagram .................. 5 cedure ......................................................................23
WITH RAIN SENSOR : System Description ............. 5 I
WITH RAIN SENSOR : Component Parts Loca- FRONT WIPER MOTOR LO CIRCUIT .............. 25
tion ............................................................................ 8 Component Function Check ....................................25
WITH RAIN SENSOR : Component Description ...... 8 Diagnosis Procedure ...............................................25 J
WITHOUT RAIN SENSOR .......................................... 9 FRONT WIPER MOTOR HI CIRCUIT ............... 27

WITHOUT RAIN SENSOR : System Diagram .......... 9 Component Function Check ....................................27
WITHOUT RAIN SENSOR : System Description ...... 9 K
Diagnosis Procedure ...............................................27
WITHOUT RAIN SENSOR : Component Parts Lo-
cation ....................................................................... 12 FRONT WIPER AUTO STOP SIGNAL CIR-
WITHOUT RAIN SENSOR : CUIT .................................................................. 29 WW
Component Description .......................................... 12 Component Function Check ....................................29
Diagnosis Procedure ...............................................29
DIAGNOSIS SYSTEM (BCM) ............................14
M
FRONT WIPER MOTOR GROUND CIRCUIT ... 31
COMMON ITEM ......................................................... 14 Diagnosis Procedure ...............................................31
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ..................................................... 14 RAIN SENSOR .................................................. 32 N
Description ...............................................................32
WIPER ....................................................................... 15 Component Function Check ....................................32
WIPER : CONSULT-III Function (BCM - WIPER).... 15 Diagnosis Procedure ...............................................32
O
DIAGNOSIS SYSTEM (IPDM E/R) .....................17 WASHER SWITCH ............................................ 34
Diagnosis Description ............................................. 17 Description ...............................................................34
CONSULT-III Function (IPDM E/R) ......................... 19 Component Inspection .............................................34 P
DTC/CIRCUIT DIAGNOSIS ......................... 22 FRONT WIPER AND WASHER SYSTEM ........ 35
Wiring Diagram - FRONT WIPER AND WASHER
WIPER AND WASHER FUSE ............................22
SYSTEM - ................................................................35
Description .............................................................. 22
Diagnosis Procedure ............................................... 22 ECU DIAGNOSIS INFORMATION .............. 39
Revision: 2010 March WW-1 2009 G37 Convertible

BCM (BODY CONTROL MODULE) .................. 39 REMOVAL AND INSTALLATION .............. 95
Reference Value ..................................................... 39
Wiring Diagram - BCM - ......................................... 62 WASHER TANK ................................................ 95
Fail-safe .................................................................. 67 Exploded View ........................................................ 95
DTC Inspection Priority Chart .............................. 69 Removal and Installation ......................................... 95
DTC Index .............................................................. 71
FRONT WASHER PUMP .................................. 96
IPDM E/R (INTELLIGENT POWER DISTRI- Exploded View ........................................................ 96
BUTION MODULE ENGINE ROOM) ................. 74 Removal and Installation ......................................... 96
Reference Value ..................................................... 74
WASHER LEVEL SWITCH ............................... 97
Wiring Diagram - IPDM E/R - .................................. 81
Removal and Installation ......................................... 97
Fail-safe .................................................................. 84
DTC Index .............................................................. 86 FRONT WASHER NOZZLE AND TUBE ........... 98
Hydraulic Layout ..................................................... 98
SYMPTOM DIAGNOSIS ............................. 87 Removal and Installation ......................................... 98
FRONT WIPER AND WASHER SYSTEM Inspection and Adjustment ...................................... 98
SYMPTOMS ....................................................... 87 FRONT WIPER ARM ........................................ 101
WITHOUT RAIN SENSOR ........................................ 87 Exploded View ...................................................... 101
WITHOUT RAIN SENSOR : Symptom Table ......... 87 Removal and Installation ....................................... 101
Adjustment ............................................................ 101
WITH RAIN SENSOR ................................................ 88
WITH RAIN SENSOR : Symptom Table ................. 88 WIPER BLADE ................................................. 103
Exploded View ...................................................... 103
FRONT WIPER DOES NOT OPERATE ............ 91 Removal and Installation ....................................... 103
Description .............................................................. 91 Replacement ......................................................... 103
Diagnosis Procedure .............................................. 91
FRONT WIPER DRIVE ASSEMBLY ................ 105
NORMAL OPERATING CONDITION ................ 93 Exploded View ...................................................... 105
Description .............................................................. 93 Removal and Installation ....................................... 105
Disassembly and Assembly .................................. 106
PRECAUTION ............................................. 94
RAIN SENSOR ................................................. 107
PRECAUTIONS ................................................. 94 Exploded View ...................................................... 107
Precaution for Supplemental Restraint System Removal and Installation ....................................... 107
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................. 94 FRONT WIPER AND WASHER SWITCH ........ 108
Precaution for Battery Service ................................ 94 Exploded View ...................................................... 108

DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
Work Flow INFOID:0000000004875932
B
OVERALL SEQUENCE
C
WW
P
JPLIA0313GB
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.

< BASIC INSPECTION >
>> GO TO 2.
2.SYMPTOM CHECK
Check the symptom from the customer's information.
>> GO TO 3.
3.BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.
>> GO TO 4.
4.SELF-DIAGNOSIS WITH CONSULT-III
Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 6.
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
>> GO TO 9.
6.FAIL-SAFE ACTIVATION CHECK
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7.
NO >> GO TO 8.
7.SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9.
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9.
9.MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10.
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is
detected before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 11.
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 3.

FRONT WIPER AND WASHER SYSTEM
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION A
WITH RAIN SENSOR
B
WITH RAIN SENSOR : System Diagram INFOID:0000000005129761
JPLIA1254GB G
WITH RAIN SENSOR : System Description INFOID:0000000005129762

H
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
I
Control by BCM
• Combination switch reading function
• Front wiper control function
J
Control by IPDM E/R
• Relay control function
K
Combination meter indicates low washer fluid warning judged with the signal from the washer level switch. For
details of low washer fluid warning, refer to MWI-27, "INFORMATION DISPLAY : System Description".
FRONT WIPER BASIC OPERATION WW
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R with CAN communication depending on each
operating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front M
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
N
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition O
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
P
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HI) to IPDM E/R with CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Front wiper switch HI

• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
FRONT WIPER AUTO OPERATION
Rain Sensing
Rain level and sensor conditions are detected by rain sensor.
• BCM transmits the vehicle conditions (vehicle speed, front wiper condition, rain sensor sensitivity setting,
etc.) to the rain sensor via the rain sensor serial link.
• Rain sensor judges a wiping speed for front wiper by rain condition and the vehicle conditions. And it trans-
mits the wiping speed request signal to the BCM via the rain sensor serial link.
Auto Wiping Operation
• BCM receives the wiping speed request signal from the rain sensor via the rain sensor serial link.
• BCM controls front wiper operation according to the wiping speed request signals. And it transmits the front
wiper request signals (LO or HI) to the IPDM E/R via CAN communication line.
Front wiper AUTO operating condition
- Front wiper switch AUTO
NOTE:
When the front wiper switch is turned to AUTO position, front wiper operates once regardless of a rainy condi-
tion.
Rain Sensor Sensitivity Setting
BCM determines rain sensor sensitivity according to a wiper volume.
Wiper volume dial position Sensitivity

1
High sensitivity
2
3
Medium − high sensitivity
4
5
Low − medium sensitivity
6
7 Low sensitivity
NOTE:
When the wiper volume is turned up at 1 level with front wiper AUTO operating condition, front wiper operates
once.
FRONT WIPER AUTO STOP OPERATION
• BCM stops transmitting the front wiper request signal when the front wiper switch is turned OFF.
• IPDM E/R detects the front wiper stop position signal from the front wiper motor and detects the front wiper
motor position (stop position/except stop position).
• When the front wiper request signal is stopped, IPDM E/R turns ON the front wiper relay until the front wiper
motor returns to the stop position.
JPLIA0410GB

NOTE:
• BCM stops the transmitting of the front wiper request signal when the ignition switch is OFF. A
• IPDM E/R turns the front wiper relay OFF when the ignition switch is OFF.
FRONT WIPER OPERATION LINKED WITH WASHER
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the B
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 2 times
when the front washer switch OFF is detected. C
Washer linked operating condition of front wiper
- Front washer switch ON (0.4 second or more) D
• The washer pump is grounded through the combination switch with the front washer switch ON.
FAIL-SAFE FUNCTION E
Front Wiper control
IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to
PCS-28, "Fail-safe". F
Rain Sensor Malfunction
• BCM judges the rain sensor serial link error by the rain sensor serial link condition and detects the rain sen-
sor malfunction by rain sensor malfunction signal. G
• When BCM detects the rain sensor serial link error or the rain sensor malfunction while front wiper AUTO
operation, BCM operates a fail-safe control.
NOTE: H
If rain sensor malfunction is detected when ignition switch is turned OFF ⇒ ON and front wiper switch is INT
position, BCM operates front wiper LO.
I
WW

WITH RAIN SENSOR : Component Parts Location INFOID:0000000005129789
JPLIA1393ZZ
1. Combination switch 2. Rain sensor 3. BCM

4. IPDM E/R 5. Washer pump 6. Washer level switch
7. Front wiper motor 8. Unified meter and A/C amp.
A. Wind shield upper B. Dash side lower (Passenger side) C. Engine room dash panel (RH)
D. Radiator core support (RH) E. Cowl top, left side of engine room F. Behind cluster lid C
WITH RAIN SENSOR : Component Description INFOID:0000000005129764
Part Description
• Judges each switch status by the combination switch reading function.
BCM • Requests (with CAN communication) the front wiper relay and the front wiper high relay ON to
IPDM E/R.
• Controls the integrated relay according to the request (with CAN communication) from BCM.
IPDM E/R
• Performs the auto stop control of the front wiper.

Part Description
A
Combination switch
Refer to BCS-6, "System Description".
(Wiper & washer switch)
Unified meter and A/C amp. Transmits the vehicle speed signal to BCM with CAN communication.
B
Detects water droplets on the windshield with infrared rays, and transmits the rain sensor signal
Rain sensor
to BCM through the rain sensor serial link.
WITHOUT RAIN SENSOR C

WITHOUT RAIN SENSOR : System Diagram INFOID:0000000004875933
H
JPLIA1255GB
WITHOUT RAIN SENSOR : System Description INFOID:0000000004875934

I
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R. J
Control by BCM
• Combination switch reading function
• Front wiper control function K
Control by IPDM E/R
• Relay control function WW
Combination meter indicates low washer fluid warning judged with the signal from the washer level switch. For
details of low washer fluid warning, refer to MWI-27, "INFORMATION DISPLAY : System Description".
FRONT WIPER BASIC OPERATION M
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R with CAN communication depending on each
operating condition of the front wiper. N
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION O
front wiper LO operating condition.
Front wiper LO operating condition P
- Front wiper switch LO or front wiper switch MIST (while pressing)
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HI) to IPDM E/R with CAN communication according to the
front wiper HI operating condition.

Front wiper HI operating condition
- Front wiper switch HI
• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
FRONT WIPER INT OPERATION
• BCM transmits the front wiper request signal (INT) to IPDM E/R with CAN communication depending on the
front wiper INT operating condition and intermittent operation delay interval according to the wiper intermit-
tent dial position.
Front wiper INT operating condition
- Front wiper switch INT
• IPDM E/R turns ON the integrated front wiper relay so that the front wiper is operated only once according to
the front wiper request signal (INT).
• BCM detects stop position/except stop position of the front wiper motor according to the front wiper stop
position signal received from IPDM E/R with CAN communication.
• BCM transmits the front wiper request signal (INT) again after the intermittent operation delay interval.
JPLIA1256GB
NOTE:
Factory setting of the front wiper intermittent operation is the operation without vehicle speed. Front wiper
intermittent operation can be set to the operation with vehicle speed by CONSULT-III. Refer to WW-15,
"WIPER : CONSULT-III Function (BCM - WIPER)".
Front wiper intermittent operation with vehicle speed
• BCM calculates the intermittent operation delay interval from the following
- Vehicle speed signal (received from the unified meter and A/C amp. with CAN communication)
- Wiper intermittent dial position
Unit: Second
Intermittent operation delay Interval
Intermittent
Wiper intermittent Vehicle speed
operation
dial position
interval 0 – 5 km/h 5 – 35 km/h 35 – 65 km/h 65 km/h (40.4 MPH)
(0 – 3.1 MPH) (3.1 – 21.7 MPH) (21.7 – 40.4 MPH)* or more
1 0.8 0.6 0.4 0.24
Short
2 ↑ 4 3 2 1.2
3 10 7.5 5 3
4 16 12 8 4.8
5 24 18 12 7.2
6 ↓ 32 24 16 9.6
Long
7 42 31.5 21 12.6
*: When without vehicle speed setting
FRONT WIPER AUTO STOP OPERATION

• BCM stops transmitting the front wiper request signal when the front wiper switch is turned OFF.
• IPDM E/R detects the front wiper stop position signal from the front wiper motor and detects the front wiper
motor position (stop position/except stop position).

• When the front wiper request signal is stopped, IPDM E/R turns ON the front wiper relay until the front wiper
motor returns to the stop position. A
JPLIA0410GB
NOTE: F
• BCM stops the transmitting of the front wiper request signal when the ignition switch is OFF.
• IPDM E/R turns the front wiper relay OFF when the ignition switch is OFF.
FRONT WIPER OPERATION LINKED WITH WASHER G
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 2 times
H
when the front washer switch OFF is detected.
Washer linked operating condition of front wiper
- Ignition switch ON I
- Front washer switch ON (0.4 second or more)
• The washer pump is grounded through the combination switch with the front washer switch ON.
J
FRONT WIPER FAIL-SAFE OPERATION
IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to
PCS-28, "Fail-safe".
K
WW

WITHOUT RAIN SENSOR : Component Parts Location INFOID:0000000004875935
JPLIA0592ZZ
1. Combination switch 2. BCM 3. IPDM E/R

4. Washer pump 5. Washer level switch 6. Front wiper motor
7. Unified meter and A/C amp.
A. Dash side lower (Passenger side) B. Engine room dash panel (RH) C. Radiator core support (RH)
D. Cowl top, left side of engine room E. Behind cluster lid C
WITHOUT RAIN SENSOR : Component Description INFOID:0000000004875936
Part Description
• Judges the each switch status by the combination switch reading function.
BCM • Requests (with CAN communication) the front wiper relay and the front wiper high relay ON to
IPDM E/R.
• Controls the integrated relay according to the request (with CAN communication) from BCM.
IPDM E/R
• Performs the auto stop control of the front wiper.

Part Description
A
Combination switch
Refer to BCS-6, "System Description".
(Wiper & washer switch)
Unified meter and A/C amp. Transmits the vehicle speed signal to BCM with CAN communication.
B
WW

DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000005162154
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode Function Description

Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
CAN Diag Support Monitor
tion manual.
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
Configuration This function is not used even though it is displayed.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
— MULTI REMOTE ENT*1
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER ×*2 × ×
Turn signal and hazard warning lamps FLASHER × × ×
— 1
AIR CONDITONER*
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW ×
Body control system BCM ×
IVIS - NATS IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk lid open TRUNK × ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER × ×
TPMS TPMS (AIR PRESSURE MONITOR) × × ×
NOTE:
• *1: This item is displayed, but is not used.
• *2: At models with rain sensor this mode is displayed, but is not used.
FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III. A
CONSULT screen item Indication/Unit Description

Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected B
Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected
While turning BCM status from low power consumption mode to
SLEEP>LOCK
normal mode (Power supply position is “LOCK”.) C
While turning BCM status from low power consumption mode to
SLEEP>OFF
normal mode (Power supply position is “OFF”.)
LOCK>ACC While turning power supply position from “LOCK” to “ACC” D
ACC>ON While turning power supply position from “ACC” to “IGN”
While turning power supply position from “RUN” to “ACC” (Vehicle
RUN>ACC
is stopping and selector lever is except P position.)
E
While turning power supply position from “CRANKING” to “RUN”

CRANK>RUN
(From cranking up the engine to run it)
F
While turning power supply position from “RUN“ to “ACC” (Emer-
RUN>URGENT
gency stop operation)
ACC>OFF While turning power supply position from “ACC” to “OFF”
G
OFF>LOCK While turning power supply position from “OFF” to “LOCK”
Power position status of
OFF>ACC While turning power supply position from “OFF” to “ACC”
Vehicle Condition the moment a particular
ON>CRANK DTC is detected While turning power supply position from “IGN” to “CRANKING” H
While turning BCM status from normal mode (Power supply posi-
OFF>SLEEP
tion is “OFF”.) to low power consumption mode
While turning BCM status from normal mode (Power supply posi- I
LOCK>SLEEP
tion is “LOCK”.) to low power consumption mode
Power supply position is “LOCK” (Ignition switch OFF with steer-
LOCK
ing is locked.) J
Power supply position is “OFF” (Ignition switch OFF with steering
OFF
is unlocked.)
ACC Power supply position is “ACC” (Ignition switch ACC) K
Power supply position is “IGN” (Ignition switch ON with engine
ON
stopped)
Power supply position is “RUN” (Ignition switch ON with engine WW
ENGINE RUN
running)
CRANKING Power supply position is “CRANKING” (At engine cranking)
The number of times that ignition switch is turned ON after DTC is detected M
• The number is 0 when a malfunction is detected now.
IGN Counter 0 - 39 • The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
N
WIPER
O
WIPER : CONSULT-III Function (BCM - WIPER) INFOID:0000000004875938
WORK SUPPORT
P
Service item Setting item Description
With vehicle speed
On
WIPER SPEED (Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
SETTING Without vehicle speed
Off*
(Front wiper intermittent time linked with the wiper intermittent dial position)
*:Initial setting

NOTE:
Work support item is not indicated when the vehicle with rain sensor.
DATA MONITOR
Monitor Item
Description
[Unit]
VEH SPEED 1 Displays the value of the vehicle speed signal received from unified meter and A/C amp. with
[km/h] CAN communication.
PUSH SW
The switch status input from push-button ignition switch.
[Off/On]
FR WIPER HI
[Off/On]
FR WIPER LOW
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP Displays the status of the front wiper stop position signal received from IPDM E/R with CAN
[Off/On] communication.
INT VOLUME
Status of each switch judged by BCM using the combination switch reading function
[1 − 7]
ACTIVE TEST
Test item Operation Description

Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to
Hi
operate the front wiper HI operation.
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
Lo
FRONT WIPER operate the front wiper LO operation.
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
INT
operate the front wiper INT operation.
Off Stops transmitting the front wiper request signal to stop the front wiper operation.

DIAGNOSIS SYSTEM (IPDM E/R)
A
Diagnosis Description INFOID:0000000005162158
AUTO ACTIVE TEST B

Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp C
• Front wiper (LO, HI)
• Parking lamps
• License plate lamps D
• Side maker lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI) E
• A/C compressor (magnet clutch)
• Cooling fan (cooling fan control module)
Operation Procedure F
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE: G
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the front door switch (driver side) 10 times. H
Then turn the ignition switch OFF.
CAUTION:
Close passenger door. I
4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
5. The oil pressure warning lamp starts blinking when the auto active test starts. J
6. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF. K
CAUTION:
• If auto active test mode cannot be actuated, check door switch system. Refer to DLK-70,
"Component Function Check". WW
• Do not start the engine.
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following 6 steps are repeated 3 times. M
Operation
Inspection location Operation
sequence
N
1 Oil pressure warning lamp Blinks continuously during operation of auto active test
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps O
• License plate lamps
3 • Side maker lamps 10 seconds
• Tail lamps
• Front fog lamps P
4 Headlamps LO ⇔ HI 5 times
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
6* Cooling fan MID for 5 seconds → HI for 5 seconds

*: Outputs duty ratio of 50% for 5 seconds → duty ratio of 100% for 5 seconds on the cooling fan control module.

Concept of auto active test
JPMIA0009GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
Symptom Inspection contents Possible cause

YES BCM signal input circuit
Any of the following components do not operate
• Parking lamps • Lamp or motor
• License plate lamps • Lamp or motor ground cir-
Perform auto active test. cuit
• Side maker lamps
Does the applicable system • Harness or connector be-
• Tail lamps NO
operate? tween IPDM E/R and appli-
• Front fog lamps
• Headlamp (HI, LO) cable system
• Front wiper (HI, LO) • IPDM E/R
• Unified meter and A/C amp.

signal input circuit
• CAN communication signal
between unified meter and
YES
A/C amp. and ECM
Perform auto active test. • CAN communication signal
A/C compressor does not operate Does the magnet clutch oper- between ECM and IPDM E/
ate? R
• Magnet clutch
• Harness or connector be-
NO tween IPDM E/R and mag-
net clutch
• IPDM E/R
tween IPDM E/R and oil
YES pressure switch
• Oil pressure switch
• IPDM E/R
Perform auto active test.
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal
lamp blink? between IPDM E/R and
BCM
NO • CAN communication signal
between BCM and unified
meter and A/C amp.
• Combination meter

Symptom Inspection contents Possible cause
A
• ECM signal input circuit
• CAN communication signal
YES
between ECM and IPDM E/
R B
• Cooling fan
tween cooling fan and cool-
ing fan control module
C
Perform auto active test.
Cooling fan does not operate • Cooling fan control module
Does the cooling fan operate?
NO tween IPDM E/R and cool- D
ing fan control module
• Cooling fan relay
tween IPDM E/R and cool- E
ing fan relay
• IPDM E/R
CONSULT-III Function (IPDM E/R) INFOID:0000000005162159

F
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R. G
Diagnosis mode Description

Ecu Identification Allows confirmation of IPDM E/R part number. H
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
I
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.
J
SELF DIAGNOSTIC RESULT
Refer to PCS-30, "DTC Index".
DATA MONITOR K
Monitor item
Monitor Item MAIN SIG-

Description WW
[Unit] NALS
RAD FAN REQ Displays the value of the cooling fan speed signal received from ECM via CAN
×
[%] communication.
M
AC COMP REQ Displays the status of the A/C compressor request signal received from ECM via
×
[Off/On] CAN communication.
TAIL&CLR REQ Displays the status of the position light request signal received from BCM via CAN
× N
HL LO REQ Displays the status of the low beam request signal received from BCM via CAN
×
O
HL HI REQ Displays the status of the high beam request signal received from BCM via CAN
×
FR FOG REQ Displays the status of the front fog light request signal received from BCM via
× P
[Off/On] CAN communication.
FR WIP REQ Displays the status of the front wiper request signal received from BCM via CAN
×
[Stop/1LOW/Low/Hi] communication.
WIP AUTO STOP
× Displays the status of the front wiper auto stop signal judged by IPDM E/R.
[STOP P/ACT P]
WIP PROT
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[Off/BLOCK]

Monitor Item MAIN SIG-
Description
[Unit] NALS
IGN RLY1 -REQ Displays the status of the ignition switch ON signal received from BCM via CAN
IGN RLY
× Displays the status of the ignition relay judged by IPDM E/R.
[Off/On]
PUSH SW
Displays the status of the push-button ignition switch judged by IPDM E/R.
[Off/On]
INTER/NP SW Displays the status of the clutch interlock switch (M/T models) or shift position (A/
[Off/On] T models) judged by IPDM E/R.
ST RLY CONT Displays the status of the starter relay status signal received from BCM via CAN
IHBT RLY -REQ Displays the status of the starter control relay signal received from BCM via CAN
ST/INHI RLY Displays the status of the starter relay and starter control relay judged by IPDM
[Off/ ST ON/INHI ON/UNKWN] E/R.
DETENT SW Displays the status of the A/T shift selector (detention switch) judged by IPDM E/
[Off/On] R.
S/L RLY -REQ Displays the status of the steering lock relay request received from BCM via CAN
S/L STATE
Displays the status of the steering lock judged by IPDM E/R.
[LOCK/UNLOCK/UNKWN]
DTRL REQ NOTE:
[Off/On] The item is indicated, but not monitored.
OIL P SW
Displays the status of the oil pressure switch judged by IPDM E/R.
[Open/Close]
HOOD SW
Displays the status of the hood switch judged by IPDM E/R.
[Off/On]
HL WASHER REQ NOTE:
THFT HRN REQ Displays the status of the theft warning horn request signal received from BCM
[Off/On] via CAN communication.
HORN CHIRP Displays the status of the horn reminder signal received from BCM via CAN com-
[Off/On] munication.
CRNRNG LMP REQ NOTE:
ACTIVE TEST
Test item

Off
NOTE:
CORNERING LAMP LH
The item is indicated, but cannot be tested.
RH
HORN On Operates horn relay 1 and horn relay 2 for 20 ms.
Off OFF
FRONT WIPER Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.
1 OFF
2 Outputs 50% pulse duty signal (PWM signal) to the cooling fan control module.
MOTOR FAN

A
NOTE:
HEAD LAMP WASHER On
The item is indicated, but cannot be tested.
Off OFF
B
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec- C
Hi
ond intervals.
Fog Operates the front fog lamp relay.
D
WW

WIPER AND WASHER FUSE
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
WIPER AND WASHER FUSE
Description INFOID:0000000004875941
Fuse list
Unit Location Fuse No. Capacity
Front wiper motor IPDM E/R #60 30 A
Washer pump IPDM E/R #47 10 A
Diagnosis Procedure INFOID:0000000004875942
1.CHECK FUSES
Check that the following fuses are not fusing.
Unit Location Fuse No. Capacity

Front wiper motor IPDM E/R #60 30 A
Washer pump IPDM E/R #47 10 A
Is the fuse fusing?
YES >> Replace the fuse with a new one after repairing the applicable circuit.
NO >> The fuse is normal.

POWER SUPPLY AND GROUND CIRCUIT
A
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure INFOID:0000000005173881
B
1.CHECK FUSE AND FUSIBLE LINK
Check that the following fuse and fusible link are not blown.
C
Signal name Fuse and fusible link No.

I D
Battery power supply
10
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is E
blown.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT F
1. Turn ignition switch OFF.

2. Disconnect BCM connectors.
G
3. Check voltage between BCM harness connector and ground.
Terminals
H
(+) (−) Voltage
BCM (Approx.)
Connector Terminal I
Ground
M118 1
Battery voltage
M119 11
J
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector. K
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
WW
BCM
Continuity
Connector Terminal Ground
M
M119 13 Existed
Does continuity exist?
YES >> INSPECTION END N
NO >> Repair harness or connector.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
O
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Di-
agnosis Procedure INFOID:0000000005173882
P
1.CHECK FUSES AND FUSIBLE LINK
Check that the following IPDM E/R fuses or fusible links are not blown.

Signal name Fuses and fusible link No.

C
Battery power supply 50
51
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
2. Disconnect IPDM E/R connector.
3. Check voltage between IPDM E/R harness connector and the ground.
Terminals
(+) Voltage
(−)
IPDM E/R (Approx.)
Connector Terminal
Ground
E4 1 Battery voltage
YES >> GO TO 3.
NO >> Repair the harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between IPDM E/R harness connectors and the ground.
IPDM E/R
Continuity
Connector Terminal
Ground
E5 12
Existed
E6 41
YES >> INSPECTION END

FRONT WIPER MOTOR LO CIRCUIT
A
Component Function Check INFOID:0000000004875945
1.CHECK FRONT WIPER LO OPERATION B

IPDM E/R AUTO ACTIVE TEST
1. Start IPDM E/R auto active test. Refer to PCS-9, "Diagnosis Description".
2. Check that the front wiper operates at the LO operation. C
CONSULT-III ACTIVE TEST
1. Select “FRONT WIPER” of IPDM E/R active test item.
2. With operating the test item, check front wiper operation. D
Lo : Front wiper (LO) operation

Off : Stop the front wiper. E
Is front wiper (LO) operation normally?
YES >> Front wiper motor LO circuit is normal.
NO >> Refer to WW-25, "Diagnosis Procedure". F
1.CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE G

1. Turn the ignition switch OFF. H
2. Disconnect front wiper motor connector.
3. Turn the ignition switch ON.
5. With operating the test item, check voltage between front wiper motor harness connector and ground. I
Terminals
Test item J
(+) (−)
Voltage (Approx.)
Front wiper motor
FRONT WIPER
Connector Terminal K
Ground
Lo Battery voltage
E42 1
Off 0V
WW
YES >> Replace front wiper motor.
NO >> GO TO 2.
M
2.CHECK FRONT WIPER MOTOR (LO) OPEN CIRCUIT
2. Disconnect IPDM E/R connector. N
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
IPDM E/R Front wiper motor O

Continuity
Connector Terminal Connector Terminal
E5 4 E42 1 Existed
P
YES >> GO TO 3.
3.CHECK FRONT WIPER MOTOR (LO) SHORT CIRCUIT
Check continuity between IPDM E/R harness connector and ground.

IPDM E/R
Continuity
E5 4 Not existed
YES >> Repair the harness or connector.
NO >> Replace IPDM E/R.

FRONT WIPER MOTOR HI CIRCUIT
A
1.CHECK FRONT WIPER HI OPERATION B

2. Check that the front wiper operates at the HI operation. C
2. With operating the test item, check front wiper operation. D
Hi : Front wiper (HI) operation

Off : Stop the front wiper. E
Is front wiper (HI) operation normally?
YES >> Front wiper motor HI circuit is normal.
1.CHECK FRONT WIPER MOTOR (HI) OUTPUT VOLTAGE G

1. Turn the ignition switch OFF. H
3. Turn the ignition switch ON.
5. With operating the test item, check voltage between front wiper motor harness connector and ground. I
Terminals
Test item J
(+) (−)
Voltage (Approx.)
Front wiper motor
FRONT WIPER
Connector Terminal K
Ground
Hi Battery voltage
E42 4
Off 0V
WW
NO >> GO TO 2.
M
2.CHECK FRONT WIPER MOTOR (HI) OPEN CIRCUIT
2. Disconnect IPDM E/R connector. N
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
IPDM E/R Front wiper motor O

Continuity
E5 5 E42 4 Existed
P
YES >> GO TO 3.
3.CHECK FRONT WIPER MOTOR (HI) SHORT CIRCUIT
Check continuity between IPDM E/R harness connector and ground.

IPDM E/R
Continuity
E5 5 Not existed
YES >> Repair the harness or connector.

FRONT WIPER AUTO STOP SIGNAL CIRCUIT
A
1.CHECK FRONT WIPER (AUTO STOP) SIGNAL B

CONSULT-III DATA MONITOR
1. Select “WIP AUTO STOP” of IPDM E/R data monitor item.
2. Operate the front wiper. C
3. With the front wiper operation, check the monitor status.
Monitor item Condition Monitor status D

Front wiper Stop position STOP P
WIP AUTO STOP
motor Except stop position ACT P
E
Is the status of item normal?
YES >> Auto stop signal circuit is normal.
1.CHECK FRONT WIPER MOTOR (AUTO STOP) OUTPUT VOLTAGE G

3. Turn the ignition switch ON. H
4. Check voltage between front wiper motor harness connector and ground.
Terminals I
(+) (−)
Voltage (Approx.)
Front wiper motor
J
E42 5 Battery voltage
Is the measurement value normal? K
NO >> GO TO 2.
2.CHECK FRONT WIPER MOTOR (AUTO STOP) OPEN CIRCUIT CONTINUITY WW

3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector. M
IPDM E/R Front wiper motor

Continuity N
E5 16 E42 5 Existed
Does continuity exist? O
YES >> GO TO 3.
NO >> Repair the harnesses or connectors.
3.CHECK FRONT WIPER MOTOR (AUTO STOP) SHORT CIRCUIT P

3. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R
Continuity
E5 16 Not existed
YES >> Repair the harnesses or connectors.

FRONT WIPER MOTOR GROUND CIRCUIT
FRONT WIPER MOTOR GROUND CIRCUIT
A
1.CHECK FRONT WIPER MOTOR (GND) OPEN CIRCUIT B

3. Check continuity between front wiper motor harness connector and ground. C
Front wiper motor

Continuity
Connector Terminal Ground D
E42 2 Existed
Does continuity exist? E
YES >> Front wiper motor ground circuit is normal.
F
WW

RAIN SENSOR
RAIN SENSOR
Rain sensor judges a wiping speed for front wiper by rain condition
and the vehicle conditions. And it transmits the wiping speed request
signal to the BCM via the rain sensor serial link.
JSLIA0093ZZ
1.CHECK FRONT WIPER AUTO OPERATION

1. Clean rain sensor detection area of windshield fully.
2. When the front wiper switch is turned to INT position, front wiper operates once regardless of a rainy con-
dition.
Is front wiper (AUTO) operation normally?
YES >> Rain sensor circuit is normal.
NO >> Refer to WW-32, "Diagnosis Procedure".
1.CHECK RAIN SENSOR FUSE

2. Check that the rain sensor 10A fuse (#6) is not fusing.
Is the fuse fusing?
YES >> Replace the fuse after repairing the applicable circuit.
NO >> GO TO 2.
2.CHECK RAIN SENSOR POWER SUPPLY
2. Disconnect rain sensor connector.
3. Turn ignition switch ON.
4. Check voltage between rain sensor harness connector and ground.
Terminal
(+) Voltage (Approx.)
(−)
Rain sensor connector Terminal
R8 1 Ground Battery voltage
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK RAIN SENSOR GROUND CIRCUIT
2. Check continuity between rain sensor harness connector and ground.

RAIN SENSOR
Rain sensor A
Continuity
R8 3 Existed
B
YES >> GO TO 4.
NO >> Repair or replace harness. C
4.CHECK RAIN SENSOR SIGNAL
1. Connect rain sensor connector.
2. Turn ignition switch ON. D
3. Check signal between BCM harness connector and ground with oscilloscope.
Terminal E
(+) Signal
Condition
(−) (Reference value)
BCM
Terminal F
connector
G
Ignition
M123 112 Ground
switch ON
H
JPMIA0156GB
Approx. 8.7V
I
YES >> Replace rain sensor. Refer to WW-107, "Exploded View".
NO >> GO TO 5.
J
5.CHECK RAIN SENSOR SIGNAL CIRCUIT FOR OPEN
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and rain sensor harness connector. K
BCM Rain sensor

Continuity WW
M123 112 R8 2 Existed
Does continuity exist? M
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK RAIN SENSOR SIGNAL CIRCUIT FOR SHORT N
Check continuity between BCM harness connector and ground.
O
BCM
Continuity
M123 112 Not existed P
YES >> Repair or replace harness.
NO >> Replace BCM. Refer to BCS-82, "Exploded View".

WASHER SWITCH
WASHER SWITCH
Washer switch is integrated with combination switch.
JPLIA0310ZZ
Component Inspection INFOID:0000000004875953
1.CHECK WIPER SWITCH

2. Disconnect combination switch connector.
3. Check continuity between the combination switch terminals.
Combination switch
Condition Continuity
Terminal
1 6 Front washer switch ON Existed
YES >> Wiper and washer switch is normal.
NO >> Replace wiper and washer switch.

A
Wiring Diagram - FRONT WIPER AND WASHER SYSTEM - INFOID:0000000004875954
WW
P
JCLWA3398GB

JCLWA3399GB

WW
JCLWA3400GB

JCLWA3401GB

< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION A
Reference Value INFOID:0000000005162168
B
VALUES ON THE DIAGNOSIS TOOL

CONSULT-III MONITOR ITEM C
Monitor Item Condition Value/Status
Other than front wiper switch HI Off
FR WIPER HI D
Front wiper switch HI On
Other than front wiper switch LO Off
FR WIPER LOW
Front wiper switch LO On
E
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On
Other than front wiper switch INT/AUTO Off F
FR WIPER INT
Front wiper switch INT/AUTO On
Front wiper is not in STOP position Off
FR WIPER STOP G
Front wiper is in STOP position On
Wiper volume dial posi-
INT VOLUME Wiper volume dial is in a dial position 1 - 7
tion
H
Other than turn signal switch RH Off
TURN SIGNAL R
Turn signal switch RH On
Other than turn signal switch LH Off I
TURN SIGNAL L
Turn signal switch LH On
Other than lighting switch 1ST and 2ND Off
TAIL LAMP SW J
Lighting switch 1ST or 2ND On
Other than lighting switch HI Off
HI BEAM SW
Lighting switch HI On K
Other than lighting switch 2ND Off
HEAD LAMP SW 1
Lighting switch 2ND On
WW
Other than lighting switch 2ND Off
HEAD LAMP SW 2
Lighting switch 2ND On
Other than lighting switch PASS Off M
PASSING SW
Lighting switch PASS On
Other than lighting switch AUTO Off
AUTO LIGHT SW N
Lighting switch AUTO On
Front fog lamp switch OFF Off
FR FOG SW
Front fog lamp switch ON On
O
NOTE:
RR FOG SW Off
The item is indicated, but not monitored.
Driver door closed Off P
DOOR SW-DR
Driver door opened On
Passenger door closed Off
DOOR SW-AS
Passenger door opened On
NOTE:
DOOR SW-RR Off

NOTE:
DOOR SW-RL Off
NOTE:
DOOR SW-BK Off
Other than power door lock switch LOCK Off
CDL LOCK SW
Power door lock switch LOCK On
Other than power door lock switch UNLOCK Off
CDL UNLOCK SW
Power door lock switch UNLOCK On
Other than driver door key cylinder LOCK position Off
KEY CYL LK-SW
Driver door key cylinder LOCK position On
Other than driver door key cylinder UNLOCK position Off
KEY CYL UN-SW
Driver door key cylinder UNLOCK position On
NOTE:
KEY CYL SW-TR Off
Hazard switch is OFF Off
HAZARD SW
Hazard switch is ON On
NOTE:
REAR DEF SW Off
NOTE:
H/L WASH SW Off
Trunk lid opener cancel switch OFF Off
TR CANCEL SW
Trunk lid opener cancel switch ON On
Trunk lid opener switch OFF Off
TR/BD OPEN SW
While the trunk lid opener switch is turned ON On
Trunk lid closed Off
TRNK/HAT MNTR
Trunk lid opened On
LOCK button of the Intelligent Key is not pressed Off
RKE-LOCK
LOCK button of the Intelligent Key is pressed On
UNLOCK button of the Intelligent Key is not pressed Off
RKE-UNLOCK
UNLOCK button of the Intelligent Key is pressed On
TRUNK OPEN button of the Intelligent Key is not pressed Off
RKE-TR/BD
TRUNK OPEN button of the Intelligent Key is pressed On
PANIC button of the Intelligent Key is not pressed Off
RKE-PANIC
PANIC button of the Intelligent Key is pressed On
UNLOCK button of the Intelligent Key is not pressed Off
RKE-P/W OPEN
UNLOCK button of the Intelligent Key is pressed and held On
LOCK/UNLOCK button of the Intelligent Key is not pressed and held simulta-
Off
RKE-MODE CHG neously
LOCK/UNLOCK button of the Intelligent Key is pressed and held simultaneously On
Bright outside of the vehicle Close to 5 V
OPTICAL SENSOR
Dark outside of the vehicle Close to 0 V
Driver door request switch is not pressed Off
REQ SW -DR
Driver door request switch is pressed On
Passenger door request switch is not pressed Off
REQ SW -AS
Passenger door request switch is pressed On
NOTE:
REQ SW -RR Off

A
NOTE:
REQ SW -RL Off
Trunk lid opener request switch is not pressed Off
REQ SW -BD/TR B
Trunk lid opener request switch is pressed On
Push-button ignition switch (push switch) is not pressed Off
PUSH SW
Push-button ignition switch (push switch) is pressed On C
Ignition switch in OFF or ACC position Off
IGN RLY2 -F/B
Ignition switch in ON position On
D
NOTE:
ACC RLY -F/B Off
The clutch pedal is not depressed Off
CLUCH SW E
The clutch pedal is depressed On
The brake pedal is depressed when No. 7 fuse is blown Off
BRAKE SW 1 The brake pedal is not depressed when No. 7 fuse is blown, or No. 7 fuse is nor-
On F
mal
The brake pedal is not depressed Off
BRAKE SW 2
The brake pedal is depressed On G
• Selector lever in P position (Except M/T models)
Off
• The clutch pedal is depressed (M/T models)
DETE/CANCL SW
• Selector lever in any position other than P (Except M/T models) H
On
• The clutch pedal is not depressed (M/T models)
Selector lever in any position other than P and N Off
SFT PN/N SW
Selector lever in P or N position On I
Steering is unlocked Off
S/L -LOCK
Steering is locked On
J
Steering is locked Off
S/L -UNLOCK
Steering is unlocked On
Ignition switch in OFF or ACC position Off K
S/L RELAY-F/B
Driver door is unlocked Off
UNLK SEN -DR WW
Driver door is locked On
Push-button ignition switch (push-switch) is not pressed Off
PUSH SW -IPDM
Push-button ignition switch (push-switch) is pressed On M
Ignition switch in OFF or ACC position Off
IGN RLY1 -F/B
N
Selector lever in any position other than P Off
DETE SW -IPDM
Selector lever in P position On
• Selector lever in any position other than P and N (Except M/T models) O
Off
• The clutch pedal is not depressed (M/T models)
SFT PN -IPDM
• Selector lever in P or N position
On
• The clutch pedal is depressed
P
Selector lever in any position other than P Off
SFT P -MET
Selector lever in P position On
Selector lever in any position other than N Off
SFT N -MET
Selector lever in N position On

Engine stopped Stop
While the engine stalls Stall
ENGINE STATE
At engine cranking Crank
Engine running Run
Steering is unlocked Off
S/L LOCK-IPDM
Steering is locked On
Steering is locked Off
S/L UNLK-IPDM
Steering is unlocked On
Steering lock system is not the LOCK condition and the changing condition from
Off
LOCK to UNLOCK
S/L RELAY-REQ
Steering lock system are not the LOCK condition or the changing condition from
On
LOCK to UNLOCK
Equivalent to speed-
VEH SPEED 1 While driving
ometer reading
Equivalent to speed-
VEH SPEED 2 While driving
ometer reading
Driver door is locked LOCK
DOOR STAT-DR Wait with selective UNLOCK operation (60 seconds) READY
Driver door is unlocked UNLOCK
Passenger door is locked LOCK
DOOR STAT-AS Wait with selective UNLOCK operation (60 seconds) READY
Passenger door is unlocked UNLOCK
Steering is locked Reset
ID OK FLAG
Steering is unlocked Set
The engine start is prohibited Reset
PRMT ENG STRT
The engine start is permitted Set
NOTE:
PRMT RKE STRT Reset
The Intelligent Key is not inserted into key slot Off
KEY SW -SLOT
The Intelligent Key is inserted into key slot On
Operation frequency of
RKE OPE COUN1 During the operation of the Intelligent Key
the Intelligent Key
NOTE:
RKE OPE COUN2 —
The key ID that the key slot receives is not recognized by any key ID registered
Yet
to BCM.
CONFRM ID ALL
The key ID that the key slot receives is recognized by any key ID registered to
Done
BCM.
The key ID that the key slot receives is not recognized by the fourth key ID regis-
Yet
tered to BCM.
CONFIRM ID4
The key ID that the key slot receives is recognized by the fourth key ID registered
Done
to BCM.
The key ID that the key slot receives is not recognized by the third key ID regis-
Yet
tered to BCM.
CONFIRM ID3
The key ID that the key slot receives is recognized by the third key ID registered
Done
to BCM.

A
The key ID that the key slot receives is not recognized by the second key ID reg-
Yet
istered to BCM.
CONFIRM ID2
The key ID that the key slot receives is recognized by the second key ID regis-
Done B
tered to BCM.
The key ID that the key slot receives is not recognized by the first key ID regis-
Yet
tered to BCM.
CONFIRM ID1 C
The key ID that the key slot receives is recognized by the first key ID registered
Done
to BCM.
The ID of fourth Intelligent Key is not registered to BCM Yet
TP 4 D
The ID of fourth Intelligent Key is registered to BCM Done
The ID of third Intelligent Key is not registered to BCM Yet
TP 3
The ID of third Intelligent Key is registered to BCM Done E
The ID of second Intelligent Key is not registered to BCM Yet
TP 2
The ID of second Intelligent Key is registered to BCM Done
The ID of first Intelligent Key is not registered to BCM Yet F
TP 1
The ID of first Intelligent Key is registered to BCM Done
Air pressure of front LH
AIR PRESS FL Ignition switch ON (Only when the signal from the transmitter is received) G
tire
Air pressure of front RH
AIR PRESS FR Ignition switch ON (Only when the signal from the transmitter is received)
tire
H
Air pressure of rear RH
AIR PRESS RR Ignition switch ON (Only when the signal from the transmitter is received)
tire
Air pressure of rear LH
AIR PRESS RL Ignition switch ON (Only when the signal from the transmitter is received) I
tire
ID of front LH tire transmitter is registered Done
ID REGST FL1
ID of front LH tire transmitter is not registered Yet
J
ID of front RH tire transmitter is registered Done
ID REGST FR1
ID of front RH tire transmitter is not registered Yet
ID of rear RH tire transmitter is registered Done K
ID REGST RR1
ID of rear RH tire transmitter is not registered Yet
ID of rear LH tire transmitter is registered Done
ID REGST RL1 WW
ID of rear LH tire transmitter is not registered Yet
Tire pressure indicator OFF Off
WARNING LAMP
Tire pressure indicator ON On M
Tire pressure warning alarm is not sounding Off
BUZZER
Tire pressure warning alarm is sounding On
N

TERMINAL LAYOUT
JPMIA0062ZZ
PHYSICAL VALUES

Terminal No. Description A

(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output
1 B
Ground Battery power supply Input Ignition switch OFF Battery voltage
(W)
2 P/W power supply
Ground Output Ignition switch OFF 12 V
(Y) (BAT) C
3 P/W power supply
Ground Output Ignition switch ON 12 V
(O) (RAP)
Interior room lamp battery saver is activated. D
0V
(Cuts the interior room lamp power supply)
4 Interior room lamp Interior room lamp battery saver is not acti-
Ground Output
(LG) power supply vated.
12 V E
(Outputs the interior room lamp power sup-
ply)
UNLOCK (Actuator is acti-
12 V F
5 Passenger door UN- Passenger vated)
Ground Output
(P) LOCK door Other than UNLOCK (Ac-
0V
tuator is not activated)
ON 0V G
7
Ground Step lamp Output Step lamp
(SB) OFF 12 V
LOCK
12 V H
8 All doors, fuel lid All doors, fuel (Actuator is activated)
Ground Output
(V) LOCK lid Other than LOCK
0V
(Actuator is not activated)
I
UNLOCK
12 V
9 Driver door, fuel lid Driver door, (Actuator is activated)
Ground Output
(G) UNLOCK fuel lid Other than UNLOCK
(Actuator is not activated)
0V J
11
(R)
K
13
Ground Ground — Ignition switch ON 0V
(B)
OFF 0V
WW
NOTE:
When the illumination brighten-
ing/dimming level is in the neutral
position. M
Push-button ignition
14
Ground switch illumination Output Tail lamp
(W) ON
ground
N
JSNIA0010GB O
OFF (LOCK indicator is
15 Battery voltage
Ground ACC indicator lamp Output Ignition switch not illuminated)
(O)
ACC 0V P

Terminal No. Description
(Wire color) Value
Input/ Condition
+ – Output
Turn signal switch OFF 0V
17 Turn signal RH Ignition switch

Ground Output
(W) (Front) ON Turn signal switch RH
PKID0926E
6.5 V
18 Ignition switch
Ground Turn signal LH (Front) Output
(O) ON Turn signal switch LH
PKID0926E
6.5 V
19 Room lamp timer Interior room OFF 12 V

Ground Output
(V) control lamp ON 0V
20 Ignition switch
Ground Turn signal RH (Rear) Output
(V) ON Turn signal switch RH
PKID0926E
6.5 V
OPEN
(Trunk lid opener actuator 12 V
23 is activated)
Ground Trunk lid open Output Trunk lid
(Y) Other than OPEN
(Trunk lid opener actuator 0V
is not activated)
25 Ignition switch
Ground Turn signal LH (Rear) Output
(Y) ON Turn signal switch LH
PKID0926E
6.5 V
30 Trunk room ON 0V
Ground Trunk room lamp Output
(P) lamp OFF 12 V

(Wire color) Value A
Input/ Condition
+ – Output
When Intelligent Key is in

the passenger compart- C
ment
JMKIA0062GB
34 Trunk room antenna Ignition switch

D
Ground Output
(SB) (−) OFF
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
When Intelligent Key is in H

the passenger compart-
ment
JMKIA0062GB
I
35 Trunk room antenna Ignition switch
Ground Output
(V) (+) OFF
J

K
ment
JMKIA0063GB
WW
M
the antenna detection
area
N
When the trunk JMKIA0062GB
lid opener re-
38 Rear bumper anten-
Ground Output quest switch is
(B) na (−)
operated with
O
ignition switch
OFF
When Intelligent Key is not P
in the antenna detection
area
JMKIA0063GB

(Wire color) Value
Input/ Condition
+ – Output

area
When the trunk JMKIA0062GB

lid opener re-
39 Rear bumper anten-
(W) na (+)
operated with
ignition switch
OFF
area
JMKIA0063GB
47 Ignition relay (IPDM OFF or ACC 12 V

Ground Output Ignition switch
(Y) E/R) control ON 0V
50 Trunk room lamp Trunk room OFF (Trunk lid is closed)

Ground Input
(G) switch lamp switch
JPMIA0011GB
11.8 V
ON (Trunk lid is opened) 0V
When selector lever is in P
Ignition switch 12 V
or N position
ON (A/T mod-
els) When selector lever is not
0V
52 in P or N position
Ground Starter relay control Output
(SB) When the clutch pedal is
Ignition switch Battery voltage
depressed
ON (M/T mod-
els) When the clutch pedal is
0V
not depressed
ON (Pressed) 0V
Trunk lid open-

61 Trunk lid opener re-
Ground Input er request
(SB) quest switch OFF (Not pressed)
switch
JPMIA0016GB
1.0 V
Intelligent Key warn- Intelligent Key Sounding 0V
64
Ground ing buzzer (Engine Output warning buzzer
(G) Not sounding 12 V
room) (Engine room)

Input/ Condition
+ – Output
Pressed 0V
B
67
Ground
Trunk lid opener
Input
Trunk lid open- C
(GR) switch er switch Not pressed
D
JPMIA0011GB
11.8 V

the passenger compart- F
ment
JMKIA0062GB
G
72 Room antenna 2 (−) Ignition switch
Ground Output
(R) (Center console) OFF
H
ment
I
JMKIA0063GB
When Intelligent Key is in K

ment
WW
JMKIA0062GB
73 Room antenna 2 (+) Ignition switch

Ground Output
(G) (Center console) OFF
M

in the passenger compart- N
ment
JMKIA0063GB
O

(Wire color) Value
Input/ Condition
+ – Output

area
When the pas- JMKIA0062GB

senger door re-
74 Passenger door an-
(SB) tenna (−)
operated with
ignition switch
OFF
area
JMKIA0063GB

area
When the pas- JMKIA0062GB

senger door re-
75 Passenger door an-
(BR) tenna (+)
operated with
ignition switch
OFF
area
JMKIA0063GB

area
When the driv- JMKIA0062GB

er door request
76 Driver door antenna
Ground Output switch is oper-
(V) (−)
ated with igni-
tion switch
OFF
area
JMKIA0063GB

Input/ Condition
+ – Output

the antenna detection C
area
When the driv- JMKIA0062GB
77 Driver door antenna

er door request D
Ground Output switch is oper-
(LG) (+)
ated with igni-
tion switch
OFF E
area
F
JMKIA0063GB
When Intelligent Key is in H

ment
JMKIA0062GB
I
78 Room antenna 1 (−) Ignition switch
Ground Output
(Y) (Instrument panel) OFF
J

K
ment
JMKIA0063GB
WW
M
ment
N
JMKIA0062GB
79 Room antenna 1 (+) Ignition switch

Ground Output
(BR) (Instrument panel) OFF O
When Intelligent Key is not P

ment
JMKIA0063GB

(Wire color) Value
Input/ Condition
+ – Output
Ignition switch is pressed Just after pressing ignition
80 Input/
Ground NATS antenna amp. During waiting while inserting the Intelli- switch. Pointer of tester should
(GR) Output
gent Key into the key slot. move.
Ignition switch is pressed Just after pressing ignition
81 Input/
Ground NATS antenna amp. During waiting while inserting the Intelli- switch. Pointer of tester should
(W) Output
gent Key into the key slot. move.
82 Ignition relay [Fuse OFF or ACC 0V

(R) block (J/B)] control ON 12 V
During waiting
JMKIA0064GB
Remote keyless entry
83 Input/
Ground receiver communica-
(Y) Output
tion
When operating either button on the Intelli-

gent Key
JMKIA0065GB
All switches OFF

(Wiper volume dial 4)
JPMIA0041GB
1.4 V
87 Combination switch Combination Front fog lamp switch ON

Ground Input
(Y) INPUT 5 switch (Wiper volume dial 4)
JPMIA0037GB
1.3 V
Any of the conditions be-

low with all switches OFF
• Wiper volume dial 1
JPMIA0040GB
1.3 V

Input/ Condition
+ – Output
All switches OFF

(Wiper volume dial 4) C
JPMIA0041GB
1.4 V D
E
Lighting switch HI
F
JPMIA0036GB
88 Combination switch Combination 1.3 V

Ground Input G
(O) INPUT 3 switch
Lighting switch 2ND

H
JPMIA0037GB
I
1.3 V
J
K
JPMIA0040GB
1.3 V WW
Push-button ig- Pressed 0V
89 Push-button ignition
Ground Input nition switch
(BR) switch (Push switch) Not pressed Battery voltage
(push switch) M
90 Input/
Ground CAN-L — —
(P) Output
91
Ground CAN-H
Input/
— —
N
(L) Output
OFF 0V
O
92 Key slot illumi- P

Ground Key slot illumination Output Blinking
(LG) nation
JPMIA0015GB
6.5 V
ON 12 V

(Wire color) Value
Input/ Condition
+ – Output
OFF (LOCK indicator is
93 Battery voltage
Ground ON indicator lamp Output Ignition switch not illuminated)
(V)
ON 0V
95 OFF 0V
Ground ACC relay control Output Ignition switch
(O) ACC or ON 12 V
A/T shift selector (De-
96
Ground tention switch) power Output — 12 V
(GR)
supply
97 Steering lock condi- LOCK status 0V

Ground Input Steering lock
(L) tion No. 1 UNLOCK status 12 V
98 Steering lock condi- LOCK status 12 V

Ground Input Steering lock
(P) tion No. 2 UNLOCK status 0V
Selector lever P posi- P position 0V

Selector lever
tion switch Any position other than P 12 V
OFF (Clutch pedal is de-
ASCD clutch switch 0V
ASCD clutch pressed)
99 (M/T models without
switch ON (Clutch pedal is not
(R)*1 Ground ICC) Input 12 V
depressed)
(BR)*2
OFF (Clutch pedal is de-
0V
ICC clutch switch (M/ ICC clutch pressed)
T models with ICC) switch ON (Clutch pedal is not
12 V
depressed)
ON (Pressed) 0V
Passenger
100 Passenger door re-
Ground Input door request
(Y) quest switch OFF (Not pressed)
switch
JPMIA0016GB
1.0 V
ON (Pressed) 0V
101 Driver door request Driver door re-

Ground Input
(P) switch quest switch OFF (Not pressed)
JPMIA0016GB
1.0 V
102 Blower fan motor re- OFF or ACC 0V

(O) lay control ON 12 V
Remote keyless entry
103
Ground receiver power sup- Output Ignition switch OFF 12 V
(L)
ply
106 Steering lock unit OFF or ACC 12 V

(W) power supply ON 0V

Input/ Condition
+ – Output
All switches OFF C
JPMIA0041GB
1.4 V D
Turn signal switch LH
F
JPMIA0037GB
1.3 V
G
Combination
107 Combination switch switch
H
Ground Input Turn signal switch RH
(LG) INPUT 1 (Wiper volume
dial 4)
JPMIA0036GB
I
1.3 V
Front wiper switch LO

K
JPMIA0038GB
1.3 V WW
Front washer switch ON
N
JPMIA0039GB
1.3 V
O

(Wire color) Value
Input/ Condition
+ – Output
All switches OFF

JPMIA0041GB
1.4 V
Lighting switch AUTO

JPMIA0038GB
108 Combination switch Combination 1.3 V

Ground Input
(R) INPUT 4 switch
Lighting switch 1ST

JPMIA0036GB
1.3 V

JPMIA0039GB
1.3 V

Input/ Condition
+ – Output
All switches OFF C
JPMIA0041GB
1.4 V D
Lighting switch PASS
F
JPMIA0037GB
1.3 V
G
Combination
H
Ground Input Lighting switch 2ND
(W) INPUT 2 (Wiper volume
dial 4)
JPMIA0036GB
I
1.3 V
Front wiper switch INT/

AUTO K
JPMIA0038GB
1.3 V WW
Front wiper switch HI
N
JPMIA0040GB
1.3 V
ON 0V O
P
110
Ground Hazard switch Input Hazard switch
(G) OFF
JPMIA0012GB
1.1 V

(Wire color) Value
Input/ Condition
+ – Output
LOCK status 12 V
LOCK or UNLOCK
111 Steering lock unit Input/
Ground Steering lock
(Y) communication Output
JMKIA0066GB
For 15 seconds after UN-

12 V
LOCK
15 seconds or later after
0V
UNLOCK
112 Rain sensor serial Input/

Ground Ignition switch ON
(R) link Output
JPMIA0156GB
8.7 V
When bright outside of the
Close to 5 V
113 Ignition switch vehicle
Ground Optical sensor Input
(O) ON When dark outside of the
Close to 0 V
vehicle
OFF (Clutch pedal is not
0V
114 Clutch interlock Clutch interlock depressed)
Ground Input
(R) switch switch ON (Clutch pedal is de-
Battery voltage
pressed)
116
Ground Stop lamp switch 1 Input — Battery voltage
(SB)
OFF (Brake pedal is not
0V
Stop lamp switch 2 Stop lamp depressed)
(Without ICC) switch ON (Brake pedal is de-
Battery voltage
118 pressed)
Ground Input
(BR) Stop lamp switch OFF (Brake pedal is not
0V
Stop lamp switch 2 depressed) and ICC brake hold relay OFF
(With ICC) Stop lamp switch ON (Brake pedal is de-
Battery voltage
pressed) or ICC brake hold relay ON
LOCK status
(Unlock sensor switch
Driver side door lock OFF)
119
Ground assembly (Unlock Input Driver door
(SB)
sensor)
JPMIA0012GB
1.1 V
UNLOCK status
(Unlock switch sensor 0V
ON)

Input/ Condition
+ – Output
When the Intelligent Key is inserted into key
12 V B
121 slot
Ground Key slot switch Input
(SB) When the Intelligent Key is not inserted into
0V
key slot
OFF or ACC 0V C
123
Ground IGN feedback Input Ignition switch
(W) ON Battery voltage
124 Passenger door Passenger OFF (Door close) E

Ground Input
(LG) switch door switch
JPMIA0011GB
F
11.8 V
ON (Door open) 0V
Trunk lid open- CANCEL H

129 Trunk lid opener can-
Ground Input er cancel
(O) cel switch
switch
JPMIA0012GB
I
1.1 V
ON 0V
J
Power window switch Ignition switch ON K

132 Input/
Ground and R.H.T. control
(V) Output
unit communication
JPMIA0013GB WW
10.2 V
Ignition switch OFF or ACC 12 V
ON (Tail lamps OFF) 9.5 V M
NOTE:
The pulse width of this wave is
varied by the illumination bright- N
ening/dimming level.
Push-button ig-
133 Push-button ignition
Ground Output nition switch il- ON (Tail lamps ON)
(L) switch illumination O
lumination
P
JPMIA0159GB
OFF 0V
134 LOCK indicator OFF Battery voltage

Ground LOCK indicator lamp Output
(LG) lamp ON 0V
137 Receiver and sensor
Ground Input Ignition switch ON 0V
(O) ground

(Wire color) Value
Input/ Condition
+ – Output
138 Receiver and sensor OFF 0V

(Y) power supply ACC or ON 5.0 V
Standby state
139 Tire pressure receiv- Input/ Ignition switch OCC3881D

Ground
(L) er communication Output ON
When receiving the signal

from the transmitter
OCC3880D
140 Selector lever P/N P or N position 12 V

Ground Input Selector lever
(GR) position (A/T models) Except P and N positions 0V
ON 0V
141 Security indicator Security indica-

Ground Output Blinking
(R) lamp tor lamp
JPMIA0014GB
11.3 V
OFF 12 V
All switches OFF 0V
Lighting switch 1ST
Lighting switch HI
Combination
142 Combination switch switch Lighting switch 2ND
Ground Output
(BR) OUTPUT 5 (Wiper volume
dial 4)
Turn signal switch RH
JPMIA0031GB
10.7 V
All switches OFF
0V
143 Combination switch Combination Any of the conditions be-
Ground Output
(P) OUTPUT 1 switch low with all switches OFF
• Wiper volume dial 6 JPMIA0032GB
• Wiper volume dial 7 10.7 V

Input/ Condition
+ – Output
All switches OFF
0V B
Front washer switch ON
144 Combination switch Combination
C
Ground Output
(O) OUTPUT 2 switch Any of the conditions be-
• Wiper volume dial 1 D
• Wiper volume dial 6 JPMIA0033GB
10.7 V
All switches OFF 0V
E
Front wiper switch INT/
AUTO
Combination F
Ground Output
(L) OUTPUT 3 (Wiper volume
dial 4)
G
Lighting switch AUTO
JPMIA0034GB
10.7 V
H
All switches OFF 0V
Front fog lamp switch ON
Lighting switch 2ND I
Combination
146 Combination switch switch Lighting switch PASS
Ground Output
(SB) OUTPUT 4 (Wiper volume
dial 4)
J
Turn signal switch LH
JPMIA0035GB
10.7 V
K
149 Tire pressure warning
Ground Input — 12 V
(W) check switch
WW
150 Driver door OFF (Door close) M

Ground Driver door switch Input
(GR) switch
JPMIA0011GB
11.8 V N
ON (Door open) 0V
151 Rear window defog- Rear window Active 0V

Ground Output O
(G) ger relay control defogger Not activated Battery voltage
• *1: A/T models
• *2: M/T models P

Wiring Diagram - BCM - INFOID:0000000005162169
JCMWA4249GB

WW
JCMWA4250GB

JCMWA4251GB

WW
JCMWA4252GB

JCMWA4253GB

WW
JCMWA4254GB
P
Fail-safe INFOID:0000000005162170
FAIL-SAFE CONTROL BY DTC

BCM performs fail-safe control when any DTC are detected.

Display contents of CONSULT Fail-safe Cancellation

B2013: ID DISCORD BCM-S/L Inhibit engine cranking Erase DTC
B2014: CHAIN OF S/L-BCM Inhibit engine cranking Erase DTC
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON → OFF
When normal vehicle speed signals are received from ABS actua-
B2557: VEHICLE SPEED Inhibit steering lock
tor and electric unit (control unit) for 500 ms
500 ms after the following CAN signal communication status be-
comes consistent
B2560: STARTER CONT RELAY Inhibit engine cranking
• Starter control relay signal
• Starter relay status signal
500 ms after the following signal reception status becomes consis-
tent
B2601: SHIFT POSITION Inhibit steering lock
• Selector lever P position switch signal
• P range signal (CAN)
5 seconds after the following BCM recognition conditions are ful-
filled
• Ignition switch is in the ON position
B2602: SHIFT POSITION Inhibit steering lock
• Selector lever P position switch signal: Except P position (battery
voltage)
• Vehicle speed: 4 km/h (2.5 MPH) or more
500 ms after the following BCM recognition conditions are fulfilled
• Ignition switch is in the ON position
B2603: SHIFT POSI STATUS Inhibit steering lock • Selector lever P position switch signal: Except P position (battery
voltage)
• Selector lever P/N position signal: Except P and N positions (0 V)
500 ms after any of the following BCM recognition conditions are
fulfilled
• Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: P and N position (battery volt-
B2604: PNP SW Inhibit steering lock age)
- P range signal or N range signal (CAN): ON
• Status 2
- Selector lever P/N position signal: Except P and N positions (0 V)
- P range signal and N range signal (CAN): OFF
500 ms after any of the following BCM recognition conditions are
fulfilled
• Status 1
- Selector lever P/N position signal: Except P and N positions (0 V)
B2605: PNP SW Inhibit steering lock - Interlock/PNP switch signal (CAN): OFF
• Status 2
- Selector lever P/N position signal: P or N position (battery volt-
age)
- PNP switch signal (CAN): ON
500 ms after the following CAN signal communication status be-
comes consistent
B2606: S/L RELAY Inhibit engine cranking
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)

Display contents of CONSULT Fail-safe Cancellation
A
500 ms after the following CAN signal communication status has
becomes consistent
B2607: S/L RELAY Inhibit engine cranking
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal) B
500 ms after the following signal communication status becomes
consistent
B2608: STARTER RELAY Inhibit engine cranking
• Starter motor relay control signal
• Starter relay status signal (CAN)
C
When the following steering lock conditions agree
• Inhibit engine cranking • BCM steering lock control status
B2609: S/L STATUS D
• Inhibit steering lock • Steering lock condition No. 1 signal status
• Steering lock condition No. 2 signal status
500 ms after the following conditions are fulfilled
• IGN relay (IPDM E/R) control signal: OFF (Battery voltage) E
B260A: IGNITION RELAY Inhibit engine cranking
• Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
Maintains the power supply When any of the following conditions are fulfilled
B260F: ENG STATE SIG LOST position attained at the time • Power position changes to ACC
F
of DTC detection • Receives engine status signal (CAN)
When any of the following conditions are fulfilled
• Steering lock unit status signal (CAN) is received normally G
• Inhibit engine cranking
B2612: S/L STATUS • The BCM steering lock control status matches the steering lock
• Inhibit steering lock
status recognized by the steering lock unit status signal (CAN
from IPDM E/R)
H
1 second after the starter motor relay control inside BCM becomes
B2617: STARTER RELAY CIRC Inhibit engine cranking
normal
1 second after the ignition relay (IPDM E/R) control inside BCM be-
B2618: BCM Inhibit engine cranking I
comes normal
1 second after the steering lock unit power supply output control in-
B2619: BCM Inhibit engine cranking
side BCM becomes normal
J
B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization
When any of the following BCM recognition conditions are fulfilled
• Status 1
- Clutch switch signal (CAN from ECM): ON
K
B26E8: CLUTCH SW Inhibit engine cranking - Clutch interlock switch signal: OFF (0 V)
• Status 2
- Clutch switch signal (CAN from ECM): OFF WW
- Clutch interlock switch signal: ON (Battery voltage)
When BCM transmits the LOCK request signal to steering lock unit,
and receives LOCK response signal from steering lock unit, the fol-
• Inhibit engine cranking M
B26E9: S/L STATUS lowing conditions are fulfilled
• Inhibit steering lock
• Steering condition No. 1 signal: LOCK (0 V)
• Steering condition No. 2 signal: LOCK (Battery voltage)
HIGH FLASHER OPERATION N

BCM detects the turn signal lamp circuit status by the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating. O
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
DTC Inspection Priority Chart INFOID:0000000005162171
P
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.

Priority DTC
1 B2562: LOW VOLTAGE
• U1000: CAN COMM
2
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
3 • B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
• B2013: ID DISCORD BCM-S/L
• B2014: CHAIN OF S/L-BCM
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2606: S/L RELAY
• B2607: S/L RELAY
• B2608: STARTER RELAY
• B2609: S/L STATUS
• B260A: IGNITION RELAY
4 • B260B: STEERING LOCK UNIT
• B260C: STEERING LOCK UNIT
• B260D: STEERING LOCK UNIT
• B260F: ENG STATE SIG LOST
• B2612: S/L STATUS
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B2619: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26E8: CLUTCH SW
• B26E9: S/L STATUS
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG

Priority DTC
A
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL B
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL C
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL D
5 • C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
E
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
F
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR G
• C1727: [BATT VOLT LOW] RL
• C1734: CONTROL UNIT
• B2621: INSIDE ANTENNA
H
6 • B2622: INSIDE ANTENNA
• B2623: INSIDE ANTENNA
DTC Index INFOID:0000000005162172 I
NOTE:
The details of time display are as follows.
J
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-15, "COM-
MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)". K
Freeze Frame Data

Tire pressure
•Vehicle Speed Intelligent Key Refer-
CONSULT display Fail-safe monitor warning WW
•Odo/Trip Meter warning lamp ON ence page
lamp ON
•Vehicle condition
No DTC is detected.
further testing — — — — — M
may be required.
U1000: CAN COMM — — — — BCS-36
U1010: CONTROL UNIT (CAN) — — — — BCS-37 N
U0415: VEHICLE SPEED SIG — — — — BCS-38
B2013: ID DISCORD BCM-S/L × × — — SEC-46
O
B2014: CHAIN OF S/L-BCM × × — — SEC-47
B2190: NATS ANTENNA AMP × — — — SEC-38
B2191: DIFFERENCE OF KEY × — — — SEC-41 P
B2192: ID DISCORD BCM-ECM × — — — SEC-42
B2193: CHAIN OF BCM-ECM × — — — SEC-44
B2195: ANTI SCANNING × — — — SEC-45
B2553: IGNITION RELAY — × — — PCS-47
B2555: STOP LAMP — × — — SEC-50

Freeze Frame Data
Tire pressure
•Vehicle Speed Intelligent Key Refer-
CONSULT display Fail-safe monitor warning
lamp ON
B2556: PUSH-BTN IGN SW — × × — SEC-52
B2557: VEHICLE SPEED × × × — SEC-54
B2560: STARTER CONT RELAY × × × — SEC-55
B2562: LOW VOLTAGE — × — — BCS-39
B2601: SHIFT POSITION × × × — SEC-56
B2602: SHIFT POSITION × × × — SEC-59
B2603: SHIFT POSI STATUS × × × — SEC-61
B2604: PNP SW × × × — SEC-64
B2605: PNP SW × × × — SEC-66
B2606: S/L RELAY × × × — SEC-68
B2607: S/L RELAY × × × — SEC-69
B2608: STARTER RELAY × × × — SEC-71
B2609: S/L STATUS × × × — SEC-73
B260A: IGNITION RELAY × × × — PCS-49
B260B: STEERING LOCK UNIT — × × — SEC-77
B260C: STEERING LOCK UNIT — × × — SEC-78
B260D: STEERING LOCK UNIT — × × — SEC-79
B260F: ENG STATE SIG LOST × × × — SEC-80
B2612: S/L STATUS × × × — SEC-85
B2614: ACC RELAY CIRC — × × — PCS-51
B2615: BLOWER RELAY CIRC — × × — PCS-54
B2616: IGN RELAY CIRC — × × — PCS-57
B2617: STARTER RELAY CIRC × × × — SEC-89
B2618: BCM × × × — PCS-60
B2619: BCM × × × — SEC-91
B261A: PUSH-BTN IGN SW — × × — PCS-61
× (Turn ON for 15
B261E: VEHICLE TYPE × × — SEC-92
seconds)
B2621: INSIDE ANTENNA — × — — DLK-61
B26E8: CLUTCH SW × × × — SEC-81
× (Turn ON for 15
B26E9: S/L STATUS × × — SEC-83
seconds)
× (Turn ON for 15
B26EA: KEY REGISTRATION — × — SEC-84
seconds)
C1704: LOW PRESSURE FL — — — ×
C1705: LOW PRESSURE FR — — — ×
WT-17
C1706: LOW PRESSURE RR — — — ×
C1707: LOW PRESSURE RL — — — ×

Freeze Frame Data
Tire pressure
•Vehicle Speed Intelligent Key Refer- A
CONSULT display Fail-safe monitor warning
lamp ON
C1708: [NO DATA] FL — — — × B
C1709: [NO DATA] FR — — — ×
WT-19
C1710: [NO DATA] RR — — — ×
C1711: [NO DATA] RL — — — × C
C1712: [CHECKSUM ERR] FL — — — ×
C1713: [CHECKSUM ERR] FR — — — ×
WT-22 D
C1714: [CHECKSUM ERR] RR — — — ×
C1715: [CHECKSUM ERR] RL — — — ×
C1716: [PRESSDATA ERR] FL — — — × E
C1717: [PRESSDATA ERR] FR — — — ×
WT-25
C1718: [PRESSDATA ERR] RR — — — ×
F
C1719: [PRESSDATA ERR] RL — — — ×
C1720: [CODE ERR] FL — — — ×
C1721: [CODE ERR] FR — — — × G
WT-27
C1722: [CODE ERR] RR — — — ×
C1723: [CODE ERR] RL — — — ×
H
C1724: [BATT VOLT LOW] FL — — — ×
C1725: [BATT VOLT LOW] FR — — — ×
WT-30
C1726: [BATT VOLT LOW] RR — — — × I
C1727: [BATT VOLT LOW] RL — — — ×
C1729: VHCL SPEED SIG ERR — — — × WT-33
J
C1734: CONTROL UNIT — — — × WT-35
WW

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
Reference Value INFOID:0000000005162173
VALUES ON THE DIAGNOSIS TOOL

Changes depending on engine
coolant temperature, air conditioner
RAD FAN REQ Engine idle speed 0 - 100 %
operation status, vehicle speed,
etc.
A/C switch OFF Off
AC COMP REQ Engine running A/C switch ON
On
(Compressor is operating)
Lighting switch OFF Off
TAIL&CLR REQ
Lighting switch 1ST, 2ND, HI or AUTO (Light is illuminated) On
HL LO REQ
Lighting switch 2ND HI or AUTO (Light is illuminated) On
HL HI REQ
Lighting switch HI On
Front fog lamp switch OFF Off
Lighting switch 2ND or • Front fog lamp switch ON
FR FOG REQ
AUTO (Light is illuminated) • Daytime running light activated On
(Only for Canada)
Front wiper switch OFF Stop
Front wiper switch INT 1LOW
FR WIP REQ Ignition switch ON
Front wiper switch LO Low
Front wiper switch HI Hi
Front wiper stop position STOP P
WIP AUTO STOP Ignition switch ON Any position other than front wiper
ACT P
stop position
Front wiper operates normally Off
WIP PROT Ignition switch ON Front wiper stops at fail-safe opera-
BLOCK
tion
Ignition switch OFF or ACC Off
IGN RLY1 -REQ
Ignition switch ON On
Ignition switch OFF or ACC Off
IGN RLY
Ignition switch ON On
Release the push-button ignition switch Off
PUSH SW
Press the push-button ignition switch On
Selector lever in any position other
Ignition switch ON than P or N (A/T models) Off
Release clutch pedal (M/T models)
INTER/NP SW
Selector lever in P or N position (A/
Ignition switch ON T models) On
Depress clutch pedal (M/T models)
Ignition switch ON Off
ST RLY CONT
At engine cranking On

A
Ignition switch ON Off
IHBT RLY -REQ
At engine cranking On
Ignition switch ON Off B
At engine cranking INHI ON → ST ON
ST/INHI RLY
The status of starter relay or starter control relay cannot be recognized by
the battery voltage malfunction, etc. when the starter relay is ON and the UNKWN C
starter control relay is OFF
• Press the selector button with se-
lector lever in P position
Ignition switch ON Off D
• Selector lever in any position oth-
DETENT SW er than P
Release the selector button with selector lever in P position
NOTE: On E
Fixed On for M/T models
None of the conditions below are present Off
• Open the driver door after the ignition switch is turned OFF (for a few F
S/L RLY -REQ seconds)
• Press the push-button ignition switch when the steering lock is activat- On
ed
G
• Depress the clutch pedal when the steering lock is activated
Steering lock is activated LOCK
S/L STATE Steering lock is deactivated UNLOCK H
[DTC: B210A] is detected UNKWN
NOTE:
DTRL REQ Off
The item is indicated, but not monitored. I
Ignition switch OFF, ACC or engine running Open
OIL P SW
Ignition switch ON Close
J
Close the hood Off
HOOD SW
Open the hood On
NOTE: K
HL WASHER REQ Off
Not operation Off
THFT HRN REQ • Panic alarm is activated WW

• Horn is activated with VEHICLE SECURITY (THEFT WARNING) SYS- On
TEM
Not operating Off M
HORN CHIRP
Door locking with Intelligent Key (horn chirp mode) On
NOTE:
CRNRNG LMP REQ Off
The item is indicated, but not monitored. N

TERMINAL LAYOUT
JSMIA0001ZZ
PHYSICAL VALUES

(Wire color) Value
Input/ Condition
+ − Output
1
(W)
2
(L)
4 Ignition Front wiper switch OFF 0V

Ground Front wiper LO Output
(V) switch ON Front wiper switch LO Battery voltage
5 Ignition Front wiper switch OFF 0V

Ground Front wiper HI Output
(L) switch ON Front wiper switch HI Battery voltage
7 Tail, license plate lamps & Ignition Lighting switch OFF 0V

Ground Output
(R) illuminations switch ON Lighting switch 1ST Battery voltage
Ignition
A few seconds after open-
switch Battery voltage
ing the driver door
OFF
11 Steering lock unit power
Ground Output Ignition
(BR) supply Press the push-button ig-
switch Battery voltage
nition switch
LOCK
Ignition switch ACC or ON 0V
12
(B/W)

Input/ Condition
+ − Output
Approximately 1 second or more after
0V B
turning the ignition switch ON
13
Ground Fuel pump power supply Output • Approximately 1 second after turning
(Y)
the ignition switch ON Battery voltage
• Engine running C
Front wiper stop position 0V
16 Ignition
Ground Front wiper auto stop Input Any position other than
(LG) switch ON Battery voltage
front wiper stop position D
19 Ignition switch OFF 0V
Ground Ignition relay power supply Output
(W) Ignition switch ON Battery voltage
E
(G) Ignition switch ON Battery voltage
26*1 Ignition switch OFF 0V F

(R) Ignition switch ON Battery voltage
27 Ignition switch OFF or ACC Battery voltage

Ground Ignition relay monitor Input G
(O) Ignition switch ON 0V
28 Push-button ignition Press the push-button ignition switch 0V

Ground Input
(L) switch Release the push-button ignition switch Battery voltage H
Selector lever in any posi-
tion other than P or N (Igni- 0V
A/T mod- tion switch ON)
els I
30 Selector lever P or N (Igni-
Ground Starter relay control Input Battery voltage
(GR) tion switch ON)
M/T mod- Release the clutch pedal 0V

J
els Depress the clutch pedal Battery voltage
32 Steering lock unit condi- Steering lock is activated 0V

Ground Input
(V) tion-1 Steering lock is deactivated Battery voltage K
33 Steering lock unit condi- Steering lock is activated Battery voltage

Ground Input
(P) tion-2 Steering lock is deactivated 0V
WW
36
(G)
39 Input/
— CAN-L — — M
(P) Output
40 Input/
— CAN-H — —
(L) Output
N
41
(B/W)
42 Ignition switch OFF or ACC 0V

Ground Cooling fan relay control Input O
(Y) Ignition switch ON 0.7 V
Press the selector button
Battery voltage
(selector lever P)
P
43*2 Ground
A/T shift selector
Input
Ignition • Selector lever in any po-
(SB) (Detention switch) switch ON sition other than P
0V
• Release the selector
button (selector lever P)
44 The horn is deactivated Battery voltage

Ground Horn relay control Input
(W) The horn is activated 0V

(Wire color) Value
Input/ Condition
+ − Output
45 The horn is deactivated Battery voltage

Ground Anti theft horn relay control Input
(G) The horn is activated 0V
Selector lever in any posi-
tion other than P or N (Igni- 0V
A/T mod- tion switch ON)
els
46 Selector lever P or N (Igni-
Ground Starter relay control Input Battery voltage
(R) tion switch ON)
M/T mod- Release the clutch pedal 0V

els Depress the clutch pedal Battery voltage
A/C switch OFF 0V
48 Engine A/C switch ON
Ground A/C relay power supply Output
(BR) running (A/C compressor is oper- Battery voltage
ating)
Ignition switch OFF
(More than a few seconds after turning 0V
ignition switch OFF)
49
Ground ECM relay power supply Output • Ignition switch ON
(O)
• Ignition switch OFF
Battery voltage
(For a few seconds after turning igni-
tion switch OFF)

(Y) Ignition switch ON Battery voltage
Ignition switch OFF
53
Ground ECM relay power supply Output • Ignition switch ON
(W)
Battery voltage
tion switch OFF)
Ignition switch OFF
54 Throttle control motor re-
Ground Output • Ignition switch ON
(P) lay power supply
Battery voltage
tion switch OFF)
55
Ground ECM power supply Output Ignition switch OFF Battery voltage
(SB)

(LG) Ignition switch ON Battery voltage

58*2 Ignition switch OFF 0V

(R) Ignition switch ON Battery voltage
Ignition switch OFF
(More than a few seconds after turning Battery voltage
69
Ground ECM relay control Output • Ignition switch ON
(BR)
0 - 1.5 V
tion switch OFF)

Input/ Condition
+ − Output
0 -1.0 V
↓ B
70 Throttle control motor re- Ignition switch ON → OFF Battery voltage
Ground Output ↓
(O) lay control
0V
C
Ignition switch ON 0 - 1.0 V
73*3 Ignition switch OFF 0V

(P) Ignition switch ON Battery voltage D
E
75 Ignition Engine stopped 0V
Ground Oil pressure switch Input
(SB) switch ON Engine running Battery voltage
Ignition switch ON G
JPMIA0001GB H
6.3 V
I
40% is set on “ACTIVE TEST”, “AL-
76 Power generation com-
Ground Output TERNATOR DUTY” of “ENGINE”
(Y) mand signal J
JPMIA0002GB
3.8 V
K
WW
80% is set on “ACTIVE TEST”, “AL-
TERNATOR DUTY” of “ENGINE”
M
JPMIA0003GB
1.4 V
• Approximately 1 second after turning N
the ignition switch ON 0 - 1.0 V
77 • Engine running
Ground Fuel pump relay control Output
(R)
Approximately 1 second or more after
Battery voltage O
turning the ignition switch ON
80
Ground Starter motor Output At engine cranking Battery voltage
(W)
P
83 Ignition Lighting switch OFF 0V
Ground Headlamp LO (RH) Output
(R) switch ON Lighting switch 2ND Battery voltage

Ground Headlamp LO (LH) Output
(P) switch ON Lighting switch 2ND Battery voltage

(Wire color) Value
Input/ Condition
+ − Output
Front fog lamp switch OFF 0V
Lighting • Front fog lamp switch

86 ON
Ground Front fog lamp (RH) Output switch
(W) • Daytime running light Battery voltage
2ND
activated (Only for Can-
ada)
Front fog lamp switch OFF 0V
Lighting • Front fog lamp switch

87 ON
Ground Front fog lamp (LH) Output switch
(L) • Daytime running light Battery voltage
2ND
activated (Only for Can-
ada)
88 Washer pump power sup-
Ground Output Ignition switch ON Battery voltage
(G) ply
Lighting switch OFF 0V
89 Ignition
Ground Headlamp HI (RH) Output • Lighting switch HI
(BR) switch ON Battery voltage
• Lighting switch PASS
Lighting switch OFF 0V
90 Ignition
Ground Headlamp HI (LH) Output • Lighting switch HI
(LG) switch ON Battery voltage
• Lighting switch PASS

Ground Parking lamp (RH) Output
(P) switch ON Lighting switch 1ST Battery voltage

Ground Parking lamp (LH) Output
(O) switch ON Lighting switch 1ST Battery voltage
97
Ground Cooling fan control Output Engine idling 0-5V
(V)
104 Close the hood Battery voltage

Ground Hood switch Input
(LG) Open the hood 0V
*1: Only for the models with ICC system
*2: A/T models only
*3: M/T models only

Wiring Diagram - IPDM E/R - INFOID:0000000005162174
WW
JCMWA4261GB
P

JCMWA4262GB

WW
JCMWA4263GB

JCMWA4264GB
Fail-safe INFOID:0000000005162175
CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With ECM

Control part Fail-safe operation A

• Outputs the pulse duty signal (PWM signal) 100% when the ignition switch is turned
Cooling fan ON
• Outputs the pulse duty signal (PWM signal) 0% when the ignition switch is turned OFF
B
A/C compressor A/C relay OFF
Alternator Outputs the power generation command signal (PWM signal) 0%
C
If No CAN Communication Is Available With BCM
Control part Fail-safe operation

D
• Turns ON the headlamp low relay when the ignition switch is turned ON
Headlamp • Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF
• Parking lamps
E
• Side maker lamp
• Turns ON the tail lamp relay when the ignition switch is turned ON
• License plate lamps
• Turns OFF the tail lamp relay when the ignition switch is turned OFF
• Illuminations
F
• Tail lamps
• The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
Front wiper • The wiper is operated at LO speed until the ignition switch is turned OFF if the fail- G
safe control is activated while the front wiper is set in the INT mode and the front wiper
motor is operating.
Horn Horn relay OFF H
Ignition relay The status just before activation of fail-safe is maintained.
Starter motor Starter control relay OFF
I
Steering lock unit Steering lock relay OFF
IGNITION RELAY MALFUNCTION DETECTION FUNCTION

• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it. J
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to K
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
Voltage judgment
WW
Ignition relay excitation coil IPDM E/R judgment Operation
Ignition relay contact side
side
ON ON Ignition relay ON normal —
M
OFF OFF Ignition relay OFF normal —
• Detects DTC “B2098: IGN RELAY ON”
ON OFF Ignition relay ON stuck • Turns ON the tail lamp relay for 10 min-
N
utes
OFF ON Ignition relay OFF stuck Detects DTC “B2099: IGN RELAY OFF”
FRONT WIPER CONTROL O

IPDM E/R detects front wiper stop position by a front wiper stop position signal.
When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 seconds activation and 20 seconds stop five times. P
Ignition switch Front wiper switch Front wiper stop position signal
The front wiper stop position signal (stop
OFF
position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does
ON
not change for 10 seconds.

NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
DTC Index INFOID:0000000005162176
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now.
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame data).
- The number is 0 when is detected now.
- The number increases like 1 → 2 ··· 38 → 39 after returning to the normal condition whenever IGN OFF →
ON.
- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
×: Applicable
CONSULT display Fail-safe Refer to
No DTC is detected.
further testing — —
may be required.
U1000: CAN COMM CIRCUIT × PCS-14
B2098: IGN RELAY ON × PCS-15
B2099: IGN RELAY OFF — PCS-16
B2108: STRG LCK RELAY ON — SEC-95
B2109: STRG LCK RELAY OFF — SEC-97
B210A: STRG LCK STATE SW — SEC-98
B210B: START CONT RLY ON — SEC-102
B210C: START CONT RLY OFF — SEC-103
B210D: STARTER RELAY ON — SEC-104
B210E: STARTER RELAY OFF — SEC-105
B210F: INTRLCK/PNP SW ON — SEC-107
B2110: INTRLCK/PNP SW OFF — SEC-109

FRONT WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
WITHOUT RAIN SENSOR
B
WITHOUT RAIN SENSOR : Symptom Table INFOID:0000000004875964
CAUTION: C
Perform the self-diagnosis with CONSULT-III before performing the diagnosis by symptom. Perform
the diagnosis by DTC if DTC is detected.
Symptom Probable malfunction location Inspection item D

• Combination switch Combination switch
• Harness between combination switch and BCM Refer to BCS-80, "Symptom
• BCM Table". E
• IPDM E/R
Front wiper motor (HI) circuit
• Harness between IPDM E/R and front wiper
HI only Refer to WW-27, "Compo-
motor F
nent Function Check".
• Front wiper motor
Front wiper request signal
IPDM E/R
• BCM
• IPDM E/R
Data monitor “FR WIP REQ” G
• BCM Table". H
Front wiper does not • IPDM E/R
Front wiper motor (LO) circuit
operate • Harness between IPDM E/R and front wiper
LO and INT Refer to WW-25, "Compo-
motor I
nent Function Check".
IPDM E/R
• BCM
Data monitor “FR WIP REQ” J
• IPDM E/R
• BCM Table". K
INT only
IPDM E/R
• BCM
Data monitor “FR WIP REQ”
• IPDM E/R WW
SYMPTOM DIAGNOSIS
HI, LO, and INT
Refer to WW-91, "Diagnosis Procedure".
M

Symptom Probable malfunction location Inspection item
Combination switch
• Combination switch
Refer to BCS-80, "Symptom
• BCM
Table".
HI only Front wiper request signal
IPDM E/R
• BCM
• IPDM E/R
IPDM E/R —
Combination switch
• BCM
Front wiper does not Table".
stop LO only Front wiper request signal
IPDM E/R
• BCM
• IPDM E/R
IPDM E/R —
Combination switch
• BCM
Table".
INT only
IPDM E/R
• BCM
• IPDM E/R
Intermittent adjustment • Harness between combination switch and BCM Refer to BCS-80, "Symptom
cannot be performed • BCM Table".
BCM —
Intermittent control
linked with vehicle Check the vehicle speed detection wiper setting.
speed cannot be per- Refer to WW-15, "WIPER : CONSULT-III Function (BCM - WIPER)".
formed
Front wiper does not • Combination switch Combination switch

operate normally Wiper is not linked to • Harness between combination switch and BCM Refer to BCS-80, "Symptom
the washer operation • BCM Table".
BCM —
Does not return to stop
position [Repeatedly
• IPDM E/R Front wiper auto stop signal
operates for 10 sec-
• Harness between IPDM E/R and front wiper circuit
onds and then stops
motor Refer to WW-29, "Compo-
for 20 seconds. After
• Front wiper motor nent Function Check".
that, it stops the opera-
tion (Fail-safe)]
WITH RAIN SENSOR

WITH RAIN SENSOR : Symptom Table INFOID:0000000005129787
CAUTION:
Perform the self-diagnosis with CONSULT-III before performing the diagnosis by symptom. Perform
the diagnosis by DTC if DTC is detected.

Symptom Probable malfunction location Inspection item A

• BCM Table".
B
• IPDM E/R
Front wiper motor (HI) circuit
HI only Refer to WW-27, "Compo-
motor
nent Function Check". C
IPDM E/R DATA MONITOR
• BCM
“FR WIP REQ”
• IPDM E/R D
• BCM Table". E
• IPDM E/R
Front wiper does not Front wiper motor (LO) circuit
operate. LO only Refer to WW-25, "Compo-
motor
nent Function Check". F
• BCM
“FR WIP REQ”
• IPDM E/R G
• BCM Table". H
AUTO only
• Rain sensor Rain sensor
• Harness between rain sensor and BCM Refer to WW-32, "Compo-
• BCM nent Function Check".
I
SYMPTOM DIAGNOSIS
HI, LO and AUTO “FRONT WIPER DOES NOT OPERATE”
J
Combination switch
• BCM
Table".
HI only Front wiper request signal K
• BCM
“FR WIP REQ”
• IPDM E/R
IPDM E/R — WW
Combination switch
• BCM
Front wiper does not Table".
M
stop. LO only Front wiper request signal
• BCM
“FR WIP REQ”
• IPDM E/R
N
IPDM E/R —
Combination switch
• BCM O
Table".
AUTO only
• Rain sensor Rain sensor
• Harness between rain sensor and BCM Refer to WW-32, "Compo-
• BCM nent Function Check". P

Symptom Probable malfunction location Inspection item
Sensitivity adjustment • Harness between combination switch and BCM Refer to BCS-80, "Symptom
cannot be performed. • BCM Table".
BCM —
Wiper is not linked to • Harness between combination switch and BCM Refer to BCS-80, "Symptom
the washer operation. • BCM Table".
Front wiper does not
operate normally. BCM —
Does not return to stop
position [Repeatedly
• IPDM E/R Front wiper auto stop signal
operates for 10 sec-
• Harness between IPDM E/R and front wiper circuit
onds and then stops
motor Refer to WW-29, "Compo-
for 20 seconds. After
• Front wiper motor nent Function Check".
that, it stops the opera-
tion. (Fail-safe)]

FRONT WIPER DOES NOT OPERATE
A
The front wiper does not operate under any operating conditions. B
1.CHECK WIPER RELAY OPERATION C

2. Check that the front wiper operates at the LO/HI operation. D
2. With operating the test item, check that front wiper LO/HI operation and OFF. E
Lo : Front wiper LO operation

Hi : Front wiper HI operation F
Off : Stop the front wiper.
Does the front wiper operate?
G
YES >> GO TO 5.
NO >> GO TO 2.
2.CHECK FRONT WIPER MOTOR FUSE H
2. Check that the front wiper motor 30 A (#60) fuse is not fusing.
Is the fuse fusing? I
YES >> Replace the fuse after repairing the applicable circuit.
NO >> GO TO 3.
3.CHECK FRONT WIPER MOTOR (GND) OPEN CIRCUIT J

Does continuity exist? K
YES >> GO TO 4.
4.CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE WW
2. Turn the ignition switch ON. M
4. With operating the test item, check voltage between IPDM E/R harness connector and ground.
N
Terminals
Test item
(+) (−)
Voltage (Approx.) O
IPDM E/R
FRONT WIPER
Connector Terminal
Lo Battery voltage
4 Ground P
Off 0V
E5
Hi Battery voltage
5
Off 0V
Is the measurement normal?

5.CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select “FR WIP REQ” of IPDM E/R data monitor item.
2. Switch the front wiper switch to HI and LO.
3. With operating the front wiper switch, check the monitor status.
Monitor item Condition Monitor status

ON Hi
OFF Stop
FR WIPER REQ
ON Low
OFF Stop
Is the status of item normal?
YES >> Replace IPDM E/R.
NO >> GO TO 6.
6.CHECK COMBINATION SWITCH
Perform the inspection of the combination switch. Refer to BCS-80, "Symptom Table".
Is combination switch normal?
YES >> Replace BCM. Refer to BCS-82, "Exploded View".
NO >> Repair or replace the applicable parts.

NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
A
FRONT WIPER MOTOR PROTECTION FUNCTION B

• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds C
or more and reactivate the front wiper. The wiper will operate normally.
WW

PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000004875968
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service INFOID:0000000004875969
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.

WASHER TANK
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION A
WASHER TANK
Exploded View INFOID:0000000004875970
B
JPLIA0559ZZ
G
1. Washer tank inlet 2. Washer tank

H
Removal and Installation INFOID:0000000004875971
REMOVAL I
1. Remove the clip (A).
: Vehicle front J
2. Pull out the washer tank inlet from the washer tank.
3. Remove the front bumper fascia. Refer to EXT-12, "Exploded
K
View".
4. Disconnect the washer pump connector.
5. Disconnect the washer level switch connector. WW
6. Disconnect the washer tube. JPLIA0077ZZ
7. Remove the washer tank mounting bolts.
8. Remove the washer tank from the vehicle. M
INSTALLATION
Install in the reverse order of removal.
CAUTION: N
Add water up to the top of the washer tank inlet after installing. Check that there is no leakage.

FRONT WASHER PUMP
FRONT WASHER PUMP
JPLIA0079ZZ
1. Washer pump connector 2. Washer pump 3. Packing

4. Washer tank
: Vehicle front
REMOVAL
1. Remove the fender protector RH (front). Refer to EXT-24, "FENDER PROTECTOR : Exploded View".
2. Disconnect the washer pump connector.
3. Disconnect the washer tube.
4. Remove the washer pump from the washer tank.
5. Remove the packing from the washer tank.
INSTALLATION
CAUTION:
Never twist the packing when installing the washer pump.

WASHER LEVEL SWITCH
WASHER LEVEL SWITCH
A
The washer level switch must be replaced together with the washer tank as an assembly. Refer to WW-95, B
"Removal and Installation".
WW

FRONT WASHER NOZZLE AND TUBE
Hydraulic Layout INFOID:0000000004875975
JPLIA0560ZZ
1. Washer tube 2. Washer nozzle 3. Washer tube

4. Washer tank
: Clip
: Clip
REMOVAL
1. Open the hood.
2. Use the stop point of washer nozzle (1) as the support point and
rotate nozzle to remove it from body, while pushing nozzle spray
point side along the hood.
3. Disconnect the washer tube (2) from the washer nozzle.
JPLIA0561ZZ
INSTALLATION
1. Connect the washer tube into the washer nozzle.
2. Install the washer nozzle to the hood.
3. Adjust the washer nozzle spray position. Refer to WW-98, "Inspection and Adjustment".
CAUTION:
The spray positions differ. Check that left and right nozzles are installed correctly.
Inspection and Adjustment INFOID:0000000004875977
INSPECTION
Washer Nozzle Inspection

Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking. A
JPLIA0562ZZ
D
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure. E
JPLIA1392ZZ
1. Black printed frame line K

: Spray area
: Target spray position
WW
Unit: mm (in)
Spray position H L X Y S
A 161 (6.34) 458 (18.03) 80 (3.15) 150 (5.91) 75 (2.95) M
B 276 (10.87) 308 (12.13) 80 (3.15) 165 (6.50) 85 (3.35)
C 270 (10.63) 113 (4.45) 80 (3.15) 150 (5.91) 75 (2.95)
N
D 284 (11.18) 92 (3.62) 80 (3.15) 165 (6.50) 80 (3.15)
E 306 (12.05) 306 (12.05) 80 (3.15) 210 (8.27) 105 (4.13)
F 279 (10.98) 439 (17.28) 80 (3.15) 130 (5.12) 65 (2.56) O

Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
JPLIA1417ZZ

FRONT WIPER ARM
FRONT WIPER ARM
A
G
JPLIA0085GB
1. Wiper blade (RH) 2. Wiper arm (RH) 3. Wiper arm cap

4. Wiper arm (LH) 5. Wiper blade (LH)
H
Refer to GI-4, "Components" for symbols in the figure.
Removal and Installation INFOID:0000000004875979 I
REMOVAL
1. Operate the front wiper to move it to the auto stop position. J
2. Open the hood.
3. Remove the wiper arm cap.
K
4. Remove the wiper arm mounting nut.
5. Raise wiper arm, and remove wiper arm from the vehicle.
INSTALLATION WW
1. Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2. Operate the front wiper motor to move the wiper to the auto stop M
position.
3. Adjust the wiper blade position. Refer to WW-101, "Adjustment".
4. Install the wiper arm by tightening the mounting nut. N
5. Inject the washer fluid.
6. Operate the front wiper to move it to the auto stop position.
O
7. Check that the wiper blades stop at the specified position.
8. Install the wiper arm cap. ELH0717D
Adjustment INFOID:0000000004875980 P
WIPER BLADE POSITION ADJUSTMENT

Clearance between the end of cowl top cover and the top of wiper blade center

FRONT WIPER ARM
Standard clearance
R : 37 ± 7.5 mm (1.457 ± 0.295 in)
L : 60 ± 7.5 mm (2.362 ± 0.295 in)
JPLIA0082ZZ

WIPER BLADE
WIPER BLADE
A
G
JPLIA1587ZZ
1. Wiper refill 2. Wiper blade 3. Wiper arm

A. Wiper blade end B. Wiper blade tip
H
I
REMOVAL
Remove the wiper blade from the wiper arm.
INSTALLATION J
Install the front wiper blade to the wiper arm.
Replacement INFOID:0000000004875983
K
1. Hold the rip of old wiper refill (1) at the rear end of the wiper
blade with long-nose pliers, and pull out the wiper refill to the
WW
direction (A).
JPLIA1583ZZ
O
2. Insert the tip of new wiper refill (1) into the rear end of wiper
blade. Slide the wiper refill to the direction (A) while pressing the
wiper refill onto the wiper blade rear end.
NOTE: P
• Insert the wiper refill to be held securely by tab (B) of wiper
blade.
• After the wiper refill is fully inserted, remove the holder* (2).
*
: Attached to service parts.
JPLIA1584ZZ

WIPER BLADE
3. Inert the wiper refill until the stopper at the rear end of wiper refill
fits in the tab. Check that “LOCK” mark on wiper refill is aligned
with “ ” mark on wiper blade.
4. Untwist the twisted wiper refill ( ) at the rear end of wiper
blade, if any.
5. Check the following items after replacing wiper refill.
• Wiper refill is not twisted at all.
• Wiper refill thoroughly fits in the tab on wiper blade.
• Wiper refill is inserted from the proper direction.
NOTE:
JPLIA1585ZZ
When the vertebra is detached.
• Insert the vertebra (1) into the wiper blade to the same bending
direction.
• If a vertebra has a notch, fit it to a protrusion inside the wiper refill.
JPLIA1586ZZ

FRONT WIPER DRIVE ASSEMBLY
A
REMOVAL VIEW B
JPLIA0565ZZ
H
1. Front wiper drive assembly
DISASSEMBLY VIEW I
WW
JPLIA0566ZZ
1. Wiper linkage 1 2. Shaft seal 3. Front wiper motor O

4. Wiper frame 5. Wiper linkage 2
: Multi−purpose grease or an equivalent.
P
REMOVAL
1. Remove the wiper arm. Refer to WW-101, "Exploded View".
2. Remove the cowl top cover. Refer to EXT-21, "Exploded View".
3. Remove the bolts from the front wiper drive assembly.

4. Disconnect the front wiper motor connector.
5. Remove the front wiper drive assembly from the vehicle.
INSTALLATION
1. Install the front wiper drive assembly to the vehicle.
2. Connect the front wiper motor connector.
4. Install the cowl top cover. Refer to EXT-21, "Exploded View".
5. Install the wiper arms. Refer to WW-101, "Exploded View".
Disassembly and Assembly INFOID:0000000004875986
DISASSEMBLY
1. Remove the wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Never bend the linkage or damage the plastic part of the ball joint when removing the wiper link-
age.
2. Remove the front wiper motor mounting screws, and then remove the front wiper motor from the wiper
frame.
ASSEMBLY
1. Connect the front wiper motor connector.
3. Disconnect the front wiper motor connector.
4. Install front wiper motor to wiper frame.
5. Install the wiper linkage 2 to the wiper motor and the wiper frame.
6. Install the wiper linkage 1 to the wiper frame.
CAUTION:
• Never drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the wiper motor and wiper linkage joint (retainer). Apply
Multi−purpose grease or an equivalent if necessary.

RAIN SENSOR
RAIN SENSOR
A
CAUTION: B
When the rain sensor is removed from windshield, the rain sensor cannot be re-used.
REMOVAL
C
JPLIA1359ZZ
H
1. Rain sensor connector 2. Inside mirror cover (upper) 3. Inside mirror cover (lower)
4. Rain sensor
A. Metal spring clip
I
Refer to GI-4, "Components" for symbols in the figure.

J
REMOVAL
1. Remove the inside mirror cover (upper and lower).
K
2. Disengage the both sides of metal spring clips, and remove the rain sensor from the windshield.
3. Disconnect the rain sensor connector.
INSTALLATION WW
CAUTION:
• Surface of windshield should be cleaned. M
• Never touch gel/adhesive of new part.
• Lock the metal spring clips and install the rain sensor securely.
N

FRONT WIPER AND WASHER SWITCH
FRONT WIPER AND WASHER SWITCH
Refer to BCS-83, "Exploded View".

Wiper & Washer: Section

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Wiper & Washer: Section

Uploaded by

Copyright:

Available Formats

DRIVER CONTROLS

WITHOUT RAIN SENSOR .......................................... 9 FRONT WIPER MOTOR HI CIRCUIT ............... 27

Revision: 2010 March WW-1 2009 G37 Convertible

Revision: 2010 March WW-2 2009 G37 Convertible

Revision: 2010 March WW-3 2009 G37 Convertible

Revision: 2010 March WW-4 2009 G37 Convertible

WITH RAIN SENSOR : System Description INFOID:0000000005129762

Revision: 2010 March WW-5 2009 G37 Convertible

Wiper volume dial position Sensitivity

Revision: 2010 March WW-6 2009 G37 Convertible

Revision: 2010 March WW-7 2009 G37 Convertible

1. Combination switch 2. Rain sensor 3. BCM

WITH RAIN SENSOR : Component Description INFOID:0000000005129764

Revision: 2010 March WW-8 2009 G37 Convertible

WITHOUT RAIN SENSOR C

WITHOUT RAIN SENSOR : System Description INFOID:0000000004875934

Revision: 2010 March WW-9 2009 G37 Convertible

*: When without vehicle speed setting

FRONT WIPER AUTO STOP OPERATION

Revision: 2010 March WW-10 2009 G37 Convertible

Revision: 2010 March WW-11 2009 G37 Convertible

1. Combination switch 2. BCM 3. IPDM E/R

WITHOUT RAIN SENSOR : Component Description INFOID:0000000004875936

Revision: 2010 March WW-12 2009 G37 Convertible

Revision: 2010 March WW-13 2009 G37 Convertible

Diagnosis mode Function Description

FREEZE FRAME DATA (FFD)

Revision: 2010 March WW-14 2009 G37 Convertible

CONSULT screen item Indication/Unit Description

While turning power supply position from “CRANKING” to “RUN”

Revision: 2010 March WW-15 2009 G37 Convertible

Test item Operation Description

Revision: 2010 March WW-16 2009 G37 Convertible

AUTO ACTIVE TEST B

6* Cooling fan MID for 5 seconds → HI for 5 seconds

Revision: 2010 March WW-17 2009 G37 Convertible

Symptom Inspection contents Possible cause

• Unified meter and A/C amp.

Revision: 2010 March WW-18 2009 G37 Convertible

CONSULT-III Function (IPDM E/R) INFOID:0000000005162159

Diagnosis mode Description

Monitor Item MAIN SIG-

Revision: 2010 March WW-19 2009 G37 Convertible

Test item Operation Description

Revision: 2010 March WW-20 2009 G37 Convertible

Revision: 2010 March WW-21 2009 G37 Convertible

Diagnosis Procedure INFOID:0000000004875942

Unit Location Fuse No. Capacity

Revision: 2010 March WW-22 2009 G37 Convertible

Signal name Fuse and fusible link No.

1. Turn ignition switch OFF.

Revision: 2010 March WW-23 2009 G37 Convertible

Signal name Fuses and fusible link No.

Revision: 2010 March WW-24 2009 G37 Convertible

1.CHECK FRONT WIPER LO OPERATION B

Lo : Front wiper (LO) operation

Diagnosis Procedure INFOID:0000000004875946

1.CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE G

CONSULT-III ACTIVE TEST

IPDM E/R Front wiper motor O

Revision: 2010 March WW-25 2009 G37 Convertible

Revision: 2010 March WW-26 2009 G37 Convertible