Security Control System: Section

BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
SECTION
SECURITY CONTROL SYSTEM
SEC B
E
CONTENTS
WITH INTELLIGENT KEY SYSTEM COMMON ITEM .........................................................20 F
COMMON ITEM : CONSULT-III Function (BCM -
BASIC INSPECTION .................................... 5 COMMON ITEM) .....................................................20
G
DIAGNOSIS AND REPAIR WORKFLOW .......... 5 IMMU ..........................................................................20
Work Flow ................................................................. 5 IMMU : CONSULT-III Function (BCM - IMMU) ........20
INSPECTION AND ADJUSTMENT ..................... 8 THEFT ALM ...............................................................21 H

THEFT ALM : CONSULT-III Function (BCM -
ADDITIONAL SERVICE WHEN REPLACING THEFT ALM) ...........................................................21
CONTROL UNIT .......................................................... 8
ADDITIONAL SERVICE WHEN REPLACING DIAGNOSIS SYSTEM (INTELLIGENT KEY I
CONTROL UNIT : Special Repair Requirement ...... 8 UNIT) ................................................................. 23
CONSULT-III Function (INTELLIGENT KEY) ..........23
ECM RE-COMMUNICATING FUNCTION ................... 8 J
ECM RE-COMMUNICATING FUNCTION : De- COMPONENT DIAGNOSIS ......................... 25
scription ..................................................................... 8
ECM RE-COMMUNICATING FUNCTION : Spe- U1000 CAN COMM CIRCUIT ........................... 25
cial Repair Requirement ............................................ 8 Description ...............................................................25 SEC
DTC Logic ................................................................25
FUNCTION DIAGNOSIS ............................... 9 Diagnosis Procedure ...............................................25
L
INTELLIGENT KEY SYSTEM/ENGINE U1010 CONTROL UNIT (CAN) ......................... 26
START FUNCTION ............................................. 9 Description ...............................................................26
System Diagram ........................................................ 9 DTC Logic ................................................................26
M
System Description ................................................... 9 Diagnosis Procedure ...............................................26
Component Parts Location ...................................... 11 Special Repair Requirement ....................................26
Component Description ........................................... 12
B2013 ID DISCORD I-KEY-STRG .................... 27 N
NVIS (NISSAN VEHICLE IMMOBILIZER SYS- Description ...............................................................27
TEM-NATS) ........................................................13 DTC Logic ................................................................27
System Diagram ...................................................... 13 Diagnosis Procedure ...............................................27
O
System Description ................................................. 13
Component Parts Location ...................................... 15 B2190, P1614 NATS ANTENNA AMP. ............ 30
Component Description .......................................... 15 Description ...............................................................30
DTC Logic ................................................................30 P
VEHICLE SECURITY SYSTEM .........................17 Diagnosis Procedure ...............................................30
System Diagram ...................................................... 17
System Description ................................................. 17 B2191, P1615 DIFFERENCE OF KEY ............. 33
Component Parts Location ...................................... 18 Description ...............................................................33
Component Description ........................................... 19 DTC Logic ................................................................33
Diagnosis Procedure ...............................................33
DIAGNOSIS SYSTEM (BCM) ............................20
SEC-1
B2192, P1611 ID DISCORD, IMMU-ECM ......... 34 Wiring Diagram - VEHICLE SECURITY SYSTEM... 51
Description .............................................................. 34 Wiring Diagram - NVIS ............................................ 61
DTC Logic ............................................................... 34 Fail Safe ................................................................. 70
Diagnosis Procedure .............................................. 34 DTC Inspection Priority Chart ............................... 70
DTC Index .............................................................. 70
B2193, P1612 CHAIN OF ECM-IMMU .............. 36
Description .............................................................. 36 INTELLIGENT KEY UNIT .................................. 71
DTC Logic ............................................................... 36 Reference Value ..................................................... 71
Diagnosis Procedure .............................................. 36 Wiring Diagram - INTELLIGENT KEY SYSTEM/
ENGINE START FUNCTION - ................................ 72
B2194 ID DISCORD IMMU-I-KEY ..................... 37 Fail Safe ................................................................. 86
Description .............................................................. 37 DTC Inspection Priority Chart ............................... 86
DTC Logic ............................................................... 37 DTC Index .............................................................. 86
Diagnosis Procedure .............................................. 37
IPDM E/R (INTELLIGENT POWER DISTRI-
B2552 INTELLIGENT KEY ................................ 38 BUTION MODULE ENGINE ROOM) ................. 87
Description .............................................................. 38 Reference Value ..................................................... 87
DTC Logic ............................................................... 38 Fail Safe ................................................................. 87
Diagnosis Procedure .............................................. 38 DTC Index .............................................................. 87
Special Repair Requirement ................................... 38
SYMPTOM DIAGNOSIS ............................ 88
B2590 ID DISCORD BCM-I-KEY ....................... 39
Description .............................................................. 39 INTELLIGENT KEY SYSTEM/ENGINE
DTC Logic ............................................................... 39 START FUNCTION SYMPTOMS ...................... 88
Diagnosis Procedure .............................................. 39 Symptom Table ....................................................... 88
P1610 LOCK MODE .......................................... 40 VEHICLE SECURITY SYSTEM SYMPTOMS ... 89
Description .............................................................. 40 Symptom Table ....................................................... 89
DTC Logic ............................................................... 40
Diagnosis Procedure .............................................. 40 NISSAN VEHICLE IMMOBILIZER SYSTEM-
NATS SYMPTOMS ............................................ 90
POWER SUPPLY AND GROUND CIRCUIT ..... 41 Symptom Table ....................................................... 90
INTELLIGENT KEY UNIT ......................................... 41 ON-VEHICLE MAINTENANCE .................. 91
INTELLIGENT KEY UNIT : Diagnosis Procedure... 41
PRE-INSPECTION FOR DIAGNOSTIC ............ 91
BCM ........................................................................... 41
Basic Inspection ...................................................... 91
BCM : Diagnosis Procedure ................................... 41
Vehicle Security Operation Check .......................... 91
KEY CYLINDER SWITCH ................................. 42
Description .............................................................. 42
ON-VEHICLE REPAIR ............................... 93
Component Function Check ................................... 42 INTELLIGENT KEY UNIT .................................. 93
Diagnosis Procedure .............................................. 42 Removal and Installation ......................................... 93
GLASS HATCH AJAR SWITCH ....................... 44 REMOVAL AND INSTALLATION .............. 94
NATS ANTENNA AMP. ..................................... 94
IGNITION KNOB SWITCH ................................. 45 Removal and Installation ......................................... 94
Ignition Knob Switch Check .................................... 45
INTELLIGENT KEY UNIT .................................. 95
HORN FUNCTION ............................................. 47 Removal and Installation ......................................... 95
Symptom Table ...................................................... 47
REMOTE KEYLESS ENTRY RECEIVER ......... 96
VEHICLE SECURITY INDICATOR .................... 48 Removal .................................................................. 96
Description .............................................................. 48
Installation ............................................................... 96
Component Function Check ................................. 48
WITHOUT INTELLIGENT KEY SYSTEM
ECU DIAGNOSIS ........................................ 50 BASIC INSPECTION .................................. 97
BCM (BODY CONTROL MODULE) .................. 50 DIAGNOSIS AND REPAIR WORKFLOW ......... 97
Work Flow ............................................................... 97
Reference Value ..................................................... 50
SEC-2
INSPECTION AND ADJUSTMENT .................. 100 Diagnosis Procedure ............................................. 114
A
ADDITIONAL SERVICE WHEN REPLACING B2192, P1611 ID DISCORD, IMMU-ECM ....... 115
CONTROL UNIT ...................................................... 100 Description ............................................................. 115
ADDITIONAL SERVICE WHEN REPLACING DTC Logic .............................................................. 115
CONTROL UNIT : Special Repair Requirement .. 100 Diagnosis Procedure ............................................. 115 B
ECM RE-COMMUNICATING FUNCTION ............... 100 B2193, P1612 CHAIN OF ECM-IMMU ............ 117
ECM RE-COMMUNICATING FUNCTION : De- Description ............................................................. 117 C
scription ................................................................. 100 DTC Logic .............................................................. 117
ECM RE-COMMUNICATING FUNCTION : Spe- Diagnosis Procedure ............................................. 117
cial Repair Requirement ........................................ 100
P1610 LOCK MODE ....................................... 118 D
FUNCTION DIAGNOSIS ............................ 101 Description ............................................................. 118
DTC Logic .............................................................. 118
NVIS (NISSAN VEHICLE IMMOBILIZER SYS- Diagnosis Procedure ............................................. 118 E
TEM-NATS) ...................................................... 101
System Diagram .................................................... 101 POWER SUPPLY AND GROUND CIRCUIT .. 119
System Description ............................................... 101
BCM ......................................................................... 119 F
Component Parts Location .................................... 102
BCM : Diagnosis Procedure .................................. 119
Component Description ........................................ 103
VEHICLE SECURITY SYSTEM ....................... 104 KEY CYLINDER SWITCH ............................... 120
G
Description ............................................................. 120
System Diagram .................................................... 104
Component Function Check .................................. 120
System Description ............................................... 104
Diagnosis Procedure ............................................. 120
Component Parts Location .................................... 105 H
Component Description ......................................... 106 GLASS HATCH AJAR SWITCH ..................... 122
DIAGNOSIS SYSTEM (BCM) .......................... 107 Diagnosis Procedure ............................................. 122
HORN FUNCTION ........................................... 123 I

COMMON ITEM ....................................................... 107
COMMON ITEM : CONSULT-III Function (BCM - Symptom Table ..................................................... 123
COMMON ITEM) ................................................... 107 VEHICLE SECURITY INDICATOR ................. 124 J
IMMU ........................................................................ 107 Description ............................................................. 124
IMMU : CONSULT-III Function (BCM - IMMU) ..... 107 Component Function Check ................................ 124
SEC
THEFT ALM ............................................................. 108
THEFT ALM : CONSULT-III Function (BCM - ECU DIAGNOSIS ....................................... 126
THEFT ALM) ......................................................... 108
BCM (BODY CONTROL MODULE) ............... 126 L
COMPONENT DIAGNOSIS ....................... 109 Reference Value .................................................... 126
Wiring Diagram - VEHICLE SECURITY SYSTEM.. 127
U1000 CAN COMM CIRCUIT ........................... 109 Wiring Diagram - NVIS - ........................................ 137
Description ............................................................ 109 M
DTC Inspection Priority Chart ............................. 144
DTC Logic ............................................................. 109 DTC Index ............................................................. 144
IPDM E/R (INTELLIGENT POWER DISTRI- N
U1010 CONTROL UNIT (CAN) ........................ 110 BUTION MODULE ENGINE ROOM) .............. 145
Description ............................................................ 110 Reference Value .................................................... 145
DTC Logic ............................................................. 110 Fail Safe ................................................................ 145 O
Diagnosis Procedure ............................................. 110 DTC Index ............................................................. 145
Special Repair Requirement ................................. 110
SYMPTOM DIAGNOSIS ............................ 146
B2190, P1614 NATS ANTENNA AMP. ............ 111 P
Description ............................................................ 111 VEHICLE SECURITY SYSTEM SYMPTOMS . 146
DTC Logic ............................................................. 111 Symptom Table ..................................................... 146
NISSAN VEHICLE IMMOBILIZER SYSTEM-
B2191, P1615 DIFFERENCE OF KEY ............. 114 NATS SYMPTOMS ......................................... 147
Description ............................................................ 114 Symptom Table ..................................................... 147
DTC Logic ............................................................. 114
SEC-3
ON-VEHICLE MAINTENANCE .................. 148 REMOVAL AND INSTALLATION ............. 150
PRE-INSPECTION FOR DIAGNOSTIC ........... 148 NATS ANTENNA AMP. .................................... 150
Basic Inspection ....................................................148 Removal and Installation ....................................... 150
ON-VEHICLE REPAIR ............................... 149 REMOTE KEYLESS ENTRY RECEIVER ........ 151
Removal ................................................................ 151
VEHICLE SECURITY SYSTEM ....................... 149 Installation ............................................................. 151
Removal and Installation .......................................149
SEC-4
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [WITH INTELLIGENT KEY SYSTEM]
BASIC INSPECTION A
Work Flow INFOID:0000000001689505
B
OVERALL SEQUENCE
C
SEC
ALKIA0538GB
DETAILED FLOW
SEC-5
1.GET INFORMATION FOR SYMPTOM

Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2.CHECK DTC
1. Check DTC for Intelligent Key unit and BCM.
2. Perform the following procedure if DTC is displayed.
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real-time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real-time diagnosis results.
>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to SEC-70, "DTC Inspection Priority Chart" (Intelligent Key unit),
SEC-70, "DTC Inspection Priority Chart" (BCM) and determine trouble diagnosis order.
Is DTC detected?
YES >> GO TO 8.
NO >> Refer to GI-51, "Intermittent Incident".
6.PERFORM BASIC INSPECTION
Perform Basic Inspection. Refer to SEC-5, "Work Flow".
>> GO TO 7.
7.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to Symptom Table based on the confirmed symptom in step 4.
>> GO TO 8.
8.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure is described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
>> GO TO 9.
SEC-6
9.REPAIR OR REPLACE THE MALFUNCTIONING PART A

1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
B
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 10.
C
10.FINAL CHECK
When DTC was detected in step 9, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunctions have been fully repaired. D
When symptom was described by the customer, refer to the confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear? E
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO >> INSPECTION END F
SEC
SEC-7
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement INFOID:0000000001689506
Refer to the CONSULT-III Operation Manual-NATS.

ECM RE-COMMUNICATING FUNCTION
ECM RE-COMMUNICATING FUNCTION : Description INFOID:0000000001689507
Performing following procedure can automatically perform re-communication of ECM and BCM, but only when
the ECM has been replaced with a new one (*1).
*1: New one means an ECM which has never been energized on-board.
(In this step, initialization procedure by CONSULT-III is not necessary)
NOTE:
• When registering new Key IDs or replacing the ECM that is not brand new, refer to CONSULT-III Oper-
ation Manual NATS.
• If multiple keys are attached to the key holder, separate them before work.
• Distinguish keys with unregistered key ID from those with registered ID.
ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement INFOID:0000000001689508
1.PERFORM ECM RE-COMMUNICATING FUNCTION

1. Install ECM.
2. Using a registered key (*2), turn ignition switch to “ON”.
*2: To perform this step, use the key that has been used before performing ECM replacement.
3. Maintain ignition switch in “ON” position for at least 5 seconds.
4. Turn ignition switch to “OFF”.
5. Start engine.
Can engine be started?
YES >> Procedure is completed.
NO >> Initialize control unit. Refer to CONSULT-III Operation Manual NATS.
SEC-8
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
FUNCTION DIAGNOSIS A
System Diagram INFOID:0000000001689509
B
ALKIA1267GB
G
System Description INFOID:0000000001689510
INPUT/OUTPUT SIGNAL CHART H

Intelligent Key Unit
Input signal to Intelligent Key unit
Switch/Input signal Actuator/Output signal
Intelligent Key unit function I
Mechanical key
Key switch
(insert/remove)
• KEY warning lamp/buzzer
Ignition knob • Steering lock unit J
Ignition knob switch
(push/release) • Starter relay request (to IPDM E/R)
Steering lock Engine start function • Inside key antenna
Steering lock unit (Instrument panel, center console,
(lock/unlock) SEC
luggage compartment)
Inside key antenna Intelligent key • Key interlock solenoid
(Front and rear center console, over- (inside antenna detection
head console, luggage compartment) area or not.)
L
IPDM E/R
Input signal to
Switch/Input signal IPDM E/R function Actuator/Output signal
IPDM E/R
M
• Starter relay
Park/neutral position switch P, N range Engine start function
• Starter motor
BCM N
Input signal to
Switch/Input signal BCM function Actuator/Output signal
BCM
• Inside key antenna O
Brake
Key switch Engine start function (Instrument panel, center console,
(press/release)
luggage compartment)
SYSTEM DESCRIPTION P
• The engine start function of Intelligent Key system is a system that makes it possible to start and stop the
engine without using the key. It verifies the electronic ID using two-way communications when pressing the
ignition knob switch while carrying the Intelligent Key, which operates based on the results of electronic ID
verification for Intelligent Key using two-way communications between the Intelligent Key and the vehicle.
NOTE:
The driver should carry the Intelligent Key at all times.
SEC-9
• Intelligent Key has 2 IDs (for Intelligent Key and for NATS). It can perform the door lock/unlock operation and
the engine start operation when the registered Intelligent Key is carried.
• When the Intelligent Key battery is discharged, it can be used as emergency back-up by inserting the
mechanical key set in the Intelligent Key to the ignition key cylinder. At that time, perform the NATS ID verifi-
cation. If it is used when the Intelligent Key is carried, perform the Intelligent Key ID verification.
• If the ID is successfully verified, and when the ignition knob switch is pressed, steering lock will be released
and initiating the engine will be possible.
• The door lock/unlock operation can be performed when the Intelligent Key battery is discharged, by operat-
ing the driver door key cylinder using the mechanical key set in the Intelligent Key.
• Up to 4 Intelligent Keys can be registered (including the standard Intelligent Key) on request from the owner.
NOTE:
• Refer to SEC-20, "COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)" for any functions
other than engine start function of Intelligent Key system.
PRECAUTIONS FOR INTELLIGENT KEY SYSTEM
• For vehicles equipped with the Intelligent Key system, the transponder [the chip for NATS ID verifi-
cation] is integrated into the Intelligent Key. Therefore, the Intelligent Key alone is capable of provid-
ing security clearance for the engine to start. Also, when the mechanical key alone is inserted into
the key cylinder, performs the NATS ID verification to allow the engine to start. For vehicles without
Intelligent Key system, the transponder is integrated into the mechanical key which must be inserted
into the key cylinder to perform the NATS ID verification to allow the engine to start.
OPERATION WHEN INTELLIGENT KEY IS CARRIED
1. When the ignition knob switch is ON, the Intelligent Key unit transmits the request signal to the Intelligent
Key.
2. The Intelligent Key receives the request signal and transmits the Intelligent Key ID signal to the Intelligent
Key unit.
3. The Intelligent Key unit receives the Intelligent Key ID signal and verifies it with the registered ID.
4. Intelligent Key unit transmits the steering lock/unlock signal to steering lock unit if the verification results
are OK. For detail of key warning lamp operation, refer to SEC-17, "System Description".
5. Release of the steering lock.
6. BCM transmits the starter request signal via CAN communication to IPDM E/R and turns the starter relay
in IPDM E/R ON if BCM judges that the engine start condition is satisfied.
7. IPDM E/R turns the starter control relay ON when receiving the starter request signal.
8. When shift position is in P or N position, battery power is supplied through the starter relay and operate
the starter motor and to start the cranking.
CAUTION:
If a malfunction is detected in the Intelligent Key system, the "NO KEY" warning message will be
displayed in the combination meter. At that time, the engine cannot be started.
OPERATION RANGE
Engine can be started when Intelligent Key is inside the vehicle. However, sometimes engine might not start
when Intelligent Key is on instrument panel or in glove box.
OPERATION WHEN MECHANICAL KEY IS USED
When the Intelligent Key battery is discharged, performs the NATS ID verification between the integrated tran-
sponder and BCM by inserting the mechanical key into the key cylinder, and then the engine can be started.
For details relating to starting the engine using mechanical key, refer to SEC-13, "System Description".
STEERING LOCK OPERATION
Steering is locked by steering lock unit when ignition switch is in the LOCK position (the ignition knob is
released) and key switch is OFF (key is removed from ignition key cylinder).
SEC-10
Component Parts Location INFOID:0000000001689511
SEC
ALKIA1268ZZ O
1. BCM M18, M19, M20 2. Intelligent Key unit M164 3. IPDM E/R
(view with instrument panel LH removed) (view with glove box removed) E119, E120, E122, E124
P
4. ECM E16 5. Key switch and ignition knob switch M66 6. Steering lock solenoid M65
(view with steering column removed)
7. Remote keyless entry receiver M67 8. A/T device (detention switch key) M156 9. Inside key antenna 1 (instrument
(view with instrument panel RH removed) (view with center console removed) panel) M68
(view with center console removed)
SEC-11
10. Inside key antenna 3 (center console) 11. Inside key antenna 2 (luggage compart- 12. Intelligent Key warning buzzer E60
M212 ment) B129
(view with center console removed) (behind 3rd row seat)
13. Combination meter M24 14. Vehicle security indicator lamp
Component Description INFOID:0000000001689512
Item Function
Intelligent Key unit Receives lock/unlock signal from remote keyless entry receiver, and then transmits to BCM.
BCM Verifies the received signal from Intelligent Key, then informs ECM whether to allow engine start.
Remote keyless entry receiver Receives lock/unlock signal from the Intelligent Key, and then transmits to Intelligent Key unit.
Intelligent Key Transmits button operation to remote keyless entry receiver.
Steering lock solenoid Locks the steering wheel when the ignition key is off and the Intelligent Key is outside the vehicle.
Inside key antenna Detects if Intelligent Key is inside the vehicle.
Intelligent Key warning buzzer Warns the user of the lock/unlock condition and inappropriate operations with the buzzer sound.
A/T device (detention key switch) Detects whether the shift lever is in park.
SEC-12
NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)
A
LIIA2537E F
G
INPUT/OUTPUT SIGNAL CHART
Intelligent Key Unit
H
Switch/Input signal Input signal to BCM BCM function Actuator/Output signal
Ignition knob
Ignition knob switch I
(push/release)
Mechanical key
Key switch
(Insert/remove) NATS • Steering lock unit
J
Steering
Steering lock unit
(lock/unlock)
ECM Engine status signal
SEC
BCM
L
Switch/Input signal Input signal to BCM BCM function Actuator/Output signal
NATS antenna amp. Key ID • Security indicator lamp
NATS
ECM Engine status signal • Starter request
M
SYSTEM DESCRIPTION
NATS (Nissan Anti-Theft System) has the following immobilizer functions:
• Engine immobilizer shows high anti-theft performance to prevent engine from starting by other than the N
owner.
• Only a key with key ID registered in BCM and ECM can start engine, and shows high anti-theft performance
to prevent key from being copied or stolen. O
• Security indicator always flashes with mechanical key removed condition (key switch: OFF) and ignition
knob released condition on LOCK position (ignition knob switch: OFF).
• Therefore, NATS warns outsiders that the vehicle is equipped with the anti-theft system. Refer to SEC-17,
"System Description". P
• If system detects malfunction, security indicator illuminates when ignition switch is turned to ON position.
• If the owner requires, ignition key ID or mechanical key ID can be registered for up to 4 keys.
• During trouble diagnosis or when the following parts have been replaced, and if mechanical key is added,
registration* is required.
*1
: All keys kept by the owner of the vehicle should be registered with mechanical key.
- ECM
- BCM
SEC-13
- Mechanical key
- Intelligent Key unit
- Remote keyless entry receiver
- Steering lock solenoid
• NATS trouble diagnosis, system initialization and additional registration of other mechanical key IDs must be
carried out using CONSULT-III.
When NATS initialization has been completed, the ID of the inserted mechanical key or mechanical key IDs
can be carried out.
• Possible symptom of NATS malfunction is “Engine cannot start”. Identify the possible causes according to
“Work Flow”, Refer to SEC-5, "Work Flow".
• If ECM other than Genuine NISSAN is installed, the engine cannot be started. For ECM replacement proce-
dure, refer to SEC-8, "ECM RE-COMMUNICATING FUNCTION : Description".
PRECAUTIONS FOR KEY REGISTRATION
• The key registration is a procedure that erases the current NATS ID once, and then re-registers a new ID.
Therefore the registered Intelligent Key is necessary for this procedure. Before starting the registration oper-
ation collect all registered Intelligent Keys from the customer.
• The NATS ID registration is the procedure that registers the ID stored into the transponder (integrated in
mechanical key) to BCM.
The Intelligent Key ID registration is the procedure that registers the ID to Intelligent Key unit.
• When performing the Intelligent Key system registration only, the engine cannot be started by inserting the
key into the key cylinder. When performing the NATS registration only, the engine cannot be started by using
the mechanical key.
SECURITY INDICATOR
• Always flashes with ignition knob released (ignition knob switch: LOCK) condition on ignition knob LOCK
position.
• Always flashes with ignition knob released (ignition knob switch: LOCK) condition on mechanical key
removed position.
MAINTENANCE INFORMATION
CAUTION:
It is necessary to perform NATS ID registration when replacing any of the following part.
If it's not (or fail to do so), the electrical system may not operate properly.
• Intelligent Key unit

• BCM
• ECM
• Mechanical key
• Steering lock solenoid
• NATS antenna amp.
SEC-14
SEC
ALKIA1269ZZ
L
1. Key switch and ignition knob switch 2. Steering lock solenoid M65 3. Remote keyless entry receiver M67
M66 (view with steering column removed) (view with glove box removed)
4. BCM M18, M20 5. Intelligent Key unit M164 6. ECM E16 M
(view with instrument panel LH re- (view with glove box removed)
moved)
7. IPDM E/R E119, E120, E122, E124 8. NATS antenna amp. M21 9. Combination meter M24
(view with cover removed) N
10. Security indicator lamp

O
Item Function
P
Intelligent Key unit Receives lock/unlock signal from remote keyless entry receiver, and then transmits to BCM.
BCM Controls the door lock function and room lamp function.
Remote keyless entry receiver Receives lock/unlock signal from the Intelligent Key, and then transmits to Intelligent Key unit.
Intelligent Key Transmits button operation to remote keyless entry receiver.
Steering lock solenoid Locks the steering wheel when the ignition key is off and the Intelligent Key is outside the vehicle.
Inside key antenna Detects if Intelligent Key is inside the vehicle.
SEC-15
Item Function
Intelligent Key warning buzzer Warns the user of the lock/unlock condition and inappropriate operations with the buzzer sound.
Ignition knob switch Monitors the status of the ignition knob switch.
NATS antenna amp. Detects the mechanical key presence in the ignition key cylinder.
Security indicator Indicates the status of the security system.
IPDM E/R Monitors the ignition switch and the park switch signal from the TCM.
SEC-16
VEHICLE SECURITY SYSTEM
A
ALKIA0709GB F
G
DESCRIPTION
The security system provides an audible and visual alarm when an unauthorized access to the vehicle is
detected while the system is in armed phase. H
The security system consist of the BCM managing the audible alarm (horn) and the visual alarm (headlamps).
OPERATION FLOW
I
SEC
PIIA1367E N
Disarmed Phase
When the vehicle is being driven or when doors are open, the theft warning system is set in the disarmed O
phase on the assumption that the owner is inside or near the vehicle.
Pre-Armed Phase And Armed Phase
The vehicle security system turns into the pre-armed phase when ignition switch is in OFF position, all doors P
are closed and locked (using Intelligent Key, door request switch or auto relock function). The system auto-
matically shifts into the armed phase.
Condition of Activating The System
When the following condition is performed in armed phase, the system sounds the horns and flashes the
headlamps for about 30 seconds.
• Any door is opened.
SEC-17
Condition of Deactivating The System
When one of the following operations is performed, the armed phase is canceled.
• Unlock the doors with Intelligent Key or door request switch.
• Use the mechanical key to unlock the driver door using the door key cylinder.
ALKIA1270ZZ
1. BCM M18, M19, M20 2. IPDM E/R E122, E123, E124 3. Horn relay H-1
(view with instrument panel LH re- (view with cover removed)
moved)
4. Main power window and door lock/ 5. Front door switch LH B8 6. Front door lock assembly LH (key cylin-
unlock switch D7, D8 RH B108 der switch) D14
7. Power window and door lock/unlock 8. Rear door switch LH B18 9. Back door cinching latch unit (door ajar
switch RH D105 RH B116 switch) D502
Glass hatch ajar switch D503
10. Horn E3 11. Combination meter M24 12. Security indicator lamp
(behind front combination lamp LH)
SEC-18
Item Function
BCM Controls the door lock function and room lamp function. B
Door switch Provides the BCM with the status of each monitored door.
C
IPDM E/R Controls the horn and headlamp operation.
Horn Sounds when the vehicle security system is triggered.
SEC
SEC-19
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001689521
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode Function Description

WORK SUPPORT Changes the setting for each system function.
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to SEC-70, "DTC Index".
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
• Enables to read and save the vehicle specification.
CONFIGURATION
• Enables to write the vehicle specification when replacing BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
— BCM ×
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITONER ×
Intelligent Key system INTELLIGENT KEY ×
Combination switch COMB SW ×
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Vehicle security system THEFT ALM × × ×
IMMU
IMMU : CONSULT-III Function (BCM - IMMU) INFOID:0000000001689522
APPLICATION ITEM

ACTIVE TEST The signals used to activate each device are forcibly supplied from Intelligent Key unit.
SEC-20
DATA MONITOR
A
Monitor item Content
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
KEY ON SW Indicates [ON/OFF] condition of key switch.
B
PUSH SW Indicates [ON/OFF] condition of ignition knob switch.
ACTIVE TEST C
Test item Description

THEFT IND This test is able to check security indicator operation [ON/OFF]. D
THEFT ALM
E
THEFT ALM : CONSULT-III Function (BCM - THEFT ALM) INFOID:0000000001689523
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM. F

G
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM. H
DATA MONITOR
Monitor Item Condition I

ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
J
I-KEY LOCK Indicates [ON/OFF] condition of lock signal from Intelligent Key. SEC
I-KEY UNLOCK Indicates [ON/OFF] condition of unlock signal from Intelligent Key.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch (driver side).
L
DOOR SW-AS Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH. M
BACK DOOR SW Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW Indicates [ON/OFF] condition of door lock and unlock switch.
N
CDL UNLOCK SW Indicates [ON/OFF] condition of door lock and unlock switch.
ACTIVE TEST
O
THEFT IND This test is able to check security indicator operation [ON/OFF].
VEHICLE SECURITY HORN This test is able to check horn operation [ON]. P
FLASHER This test is able to check flasher operation [LH/RH/OFF].
WORK SUPPORT
SEC-21

Vehicle security function mode can be changed in this mode.
SECURITY ALARM SET • ON: Vehicle security function is ON.
• OFF: Vehicle security function is OFF.
The switch which triggered vehicle security system is recorded. This mode can be able to con-
THEFT ALM TRG
firm and erase the record of vehicle security system.
SEC-22
DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)
A
CONSULT-III Function (INTELLIGENT KEY) INFOID:0000000001689524
APPLICATION ITEM B
CONSULT-III performs the following functions via CAN communication with Intelligent Key unit.
Diagnosis mode Function Description C

SELF-DIAG RESULTS Displays the diagnosis results judged by Intelligent Key unit.
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from Intelligent Key unit. D
DATA MONITOR The Intelligent Key unit input/output signals are displayed.
E
ECU IDENTIFICATION The Intelligent Key unit part number is displayed.
WORK SUPPORT
F
Support item Description Selection item Condition
It can check whether Intelligent Key ID code
CONFIRM KEY FOB ID — — G
is registered or not.
Take away warning chime (from window) ON Active

TAKE OUT FROM WINDOW WARN
mode can be changed. OFF Inactive H
Intelligent Key low battery warning mode can ON Active
LOW BATT OF KEY FOB WARN
be changed. OFF Inactive
Door lock function with Intelligent Key can be ON Active I

KEYLESS FUNCTION
changed. OFF Inactive
ON Active
ANSWER BACK FUNCTION Buzzer reminder operation can be changed. J
OFF Inactive
ON Active
SELECTIVE UNLOCK FUNCTION Anti-hijack mode can be changed.
OFF Inactive SEC
Hazard reminder operation mode can be
HAZARD ANSWER BACK Refer to SEC-20.
changed.
Buzzer reminder operation (lock operation) BUZZER Active L
ANSWER BACK WITH I-KEY LOCK mode by each door request switch can be
Buzzer reminder operation (unlock operation) BUZZER Active M

ANSWER BACK WITH I-KEY UNLOCK mode by each door request switch can be
Auto door lock operation mode can be OFF Inactive

AUTO RELOCK TIMER N
changed. 1 min Active
Engine start function (by Intelligent Key) ON Active

ENGINE START BY I-KEY
mode can be changed. OFF Inactive O
Door lock function by door request switch can ON Active

LOCK/UNLOCK BY I-KEY
be changed. OFF Inactive
P
SELF-DIAG RESULT
Refer to SEC-70, "DTC Index".
DATA MONITOR
SEC-23
Monitor Item Condition

PUSH SW Indicates [ON (pressed)/OFF (released)] condition of ignition knob switch.
KEY SW Indicates [ON (inserted)/OFF (removed)] condition of key switch.
DR REQ SW Indicates [ON (pressed)/OFF (released)] condition of door request switch (driver side).
Indicates [ON (pressed)/OFF (released)] condition of door request switch (passenger
AS REQ SW
side).
BD/TR REQ SW Indicates [ON (pressed)/OFF (released)] condition of door request switch (back door).
Indicates [ON (ON or START position)/OFF (other than ON and START position)] con-
IGN SW
dition of ignition switch ON position.
ACC SW Indicates [ON/OFF] condition of ignition switch ACC position.
STOP LAMP SW Indicates [ON/OFF] condition of stop lamp switch.
DOOR LOCK SIG Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
DOOR UNLOCK SIG Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
Indicates [OPEN/CLOSE] condition of front door switch (driver side) from BCM via CAN
DOOR SW DR
communication.
Indicates [OPEN/CLOSE] condition of front door switch (passenger side) from BCM via
DOOR SW AS
CAN communication.
Indicates [OPEN/CLOSE] condition of rear door switch (RH) from BCM via CAN com-
DOOR SW RR
munication.
Indicates [OPEN/CLOSE] condition of rear door switch (LH) from BCM via CAN com-
DOOR SW RL
munication.
Indicates [OPEN/CLOSE] condition of back door switch from BCM via CAN communi-
DOOR BK SW
cation.
Displays the vehicle speed signal received from combination meter by numerical value
VEHICLE SPEED
[km/h].
ACTIVE TEST

This test is able to check door lock/unlock operation.
• ALL UNLK: All door lock actuators are unlocked.
• DR UNLK: Door lock actuator (driver side) is unlocked.
DOOR LOCK/UNLOCK
• AS UNLK: Door lock actuator (passenger side) is unlocked.
• BK UNLK: This item is indicated, but inactive.
• LOCK: All door lock actuator is locked.
This test is able to check Intelligent Key antenna operation.
When the following condition are met, hazard warning lamps flash.
• ROOM ANT1: Inside key antenna (console) detects Intelligent Key, when “ROOM
ANT1” is selected.
• ROOM ANT2: Inside key antenna (instrument center/rear seat) detects Intelligent
Key, when “ROOM ANT2”is selected.
ANTENNA
• DRIVER ANT: Outside key antenna (driver side) detects Intelligent Key, when “DRIV-
ER ANT” is selected.
• ASSIST ANT: Outside key antenna (passenger side) detects Intelligent Key, when
“ASSIST ANT” is selected.
• BK DOOR ANT: Outside key antenna (rear bumper) detects Intelligent Key, when “BK
DOOR ANT” is selected.
This test is able to check Intelligent Key warning buzzer operation.
OUTSIDE BUZZER • ON
• OFF
This test is able to check warning chime in combination meter operation.
• TAKE OUT: Take away warning chime sounds.
INSIDE BUZZER • KNOB: Ignition knob switch warning chime sounds.
• KEY: Key warning chime sounds.
• OFF
SEC-24
U1000 CAN COMM CIRCUIT
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
COMPONENT DIAGNOSIS A
Description INFOID:0000000001689525
B
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with C
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only. D
CAN Communication Signal Chart, refer to LAN-57, "CAN Communication Signal Chart".
DTC Logic INFOID:0000000001689526
E
DTC DETECTION LOGIC
CONSULT-III display F
DTC DTC Detection Condition Possible cause
description
In CAN communication system, any item (or items)
of the following listed below is malfunctioning. G
When Intelligent Key unit cannot communi-
• Transmission
U1000 CAN COMM CIRCUIT cate CAN communication signal continuous-
• Receiving (BCM)
ly for 2 seconds or more.
• Receiving (ECM)
• Receiving (METER/M&A) H
Diagnosis Procedure INFOID:0000000001689527
I
1.PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result”. J
Is “CAN COMM CIRCUIT” displayed?
YES >> Refer to LAN-5, "CAN Communication Control Circuit".
NO >> Refer to GI-51, "Intermittent Incident". SEC
SEC-25
U1010 CONTROL UNIT (CAN)
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC DETECTION LOGIC
CONSULT-III display de-

scription
When detecting error during the initial diagnosis of CAN control-
U1010 CONTROL UNIT (CAN) Intelligent Key unit
ler of Intelligent Key unit.
1.REPLACE INTELLIGENT KEY UNIT

When DTC [U1010] is detected, replace Intelligent Key unit.
>> Replace Intelligent Key unit. Refer to SEC-95, "Removal and Installation".
Special Repair Requirement INFOID:0000000001689531
1.REQUIRED WORK WHEN REPLACING INTELLIGENT KEY UNIT

Initialize control unit. Refer to CONSULT-III Operation Manual.
>> Work end.
SEC-26
B2013 ID DISCORD I-KEY-STRG
A
Intelligent Key unit performs the ID verification with the steering lock unit and releases the steering lock if both B
Intelligent Key unit and steering lock unit ID are same. Intelligent Key unit starts the communication with the
steering lock unit when Intelligent Key is carried into the vehicle and the ignition knob switch is pressed.
DTC Logic INFOID:0000000001689533 C
DTC DETECTION LOGIC

D
Trouble diagnosis
DTC No. DTC detecting condition Possible cause
name
The ID verification results between Intelligent Key E
B2013 STRG COMM 1 unit and steering control unit are NG. The registra- Steering lock unit
tion is necessary.
DTC CONFIRMATION PROCEDURE F

1. Press the ignition knob switch G
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SEC-27, "Diagnosis Procedure". H
NO >> INSPECTION END.
I
1.PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Manual”. J
Can the system be initialized and can steering lock be released with re-registered mechanical key?
YES >> Steering lock solenoid was unregistered.
NO >> GO TO 2 SEC
2.CHECK STEERING LOCK SOLENOID POWER SUPPLY-1

1. Turn ignition switch OFF. L
2. Disconnect steering lock solenoid connector.
3. Check voltage between steering lock solenoid harness connec-
tor and ground.
M
Terminals
(+) Voltage (V)
(Approx.) N
Steering lock solenoid con- (–)
Terminal
nector
M65 1 Ground Battery voltage
O
Is the inspection result normal?
YES >> GO TO 3 PIIB6632E
NO >> Repair or replace harness. P

3.CHECK STEERING LOCK SOLENOID GROUND CIRCUIT
SEC-27
Check continuity between steering lock solenoid harness connector
and ground.
Terminals
(+)
Continuity
Steering lock solenoid con- (–)
Terminal
nector
M65 4 Ground Yes
YES >> GO TO 4 PIIB6633E
NO >> Repair or replace harness.

4.CHECK STEERING LOCK SOLENOID COMMUNICATION CIRCUITS
1. Disconnect Intelligent Key unit connector.
2. Check continuity between steering lock solenoid connector (A)
M65 terminals 2, 3 and Intelligent Key unit connector (B) M164
terminals 1, 32.
Terminals
Steering lock sole- Intelligent Key unit Continuity
Terminal Terminal
noid connector connector
2 1
M65 M164 Yes
3 32
3. Check continuity between steering lock solenoid connector (A) ALKIA1272ZZ
M65 terminals 2, 3 and ground.
Terminals
Continuity
Steering lock solenoid connector Terminals
2
M65 Ground No
3
YES >> GO TO 5
5.CHECK INTELLIGENT KEY UNIT POWER SUPPLY-2
1. Connect Intelligent Key unit connector.
2. Check voltage between Intelligent Key unit harness connector
and ground.
Terminals
Voltage (V)
(+)
(–) (Approx.)
Intelligent Key unit connector Terminal
M164 1 Ground 5
YES >> GO TO 6
WIIA1204E
NO >> Replace Intelligent Key unit. Refer to SEC-93, "Removal
and Installation".
6.CHECK STEERING LOCK SOLENOID COMMUNICATION CIRCUIT
1. Connect steering lock solenoid connector.
SEC-28
2. Using an oscilloscope, check voltage between Intelligent Key
unit connector and ground. A
WIIA1205E
Terminals
(+) Voltage (V) E
Condition
(–) (Approx.)
Intelligent Key
Terminal
unit connector
F
Ignition knob is pushed G
SIIA1911J
H
LOCK status 5
Steering I
M164 32 Ground
lock
LOCK ⇔ UNLOCK
J
JMKIA0433ZZ
SEC
For 15 seconds after
5
UNLOCK
15 seconds later UN- L
0
LOCK
YES >> Replace Steering lock solenoid. M
NO >> Replace Intelligent Key unit. Refer to SEC-93, "Removal and Installation".
SEC-29
B2190, P1614 NATS ANTENNA AMP.
Performs ID verification through BCM and NATS antenna amplifier when ignition knob switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered ID of mechanical key is used.
DTC DETECTION LOGIC
Trouble diagnosis
name
B2190 • Harness or connectors
(The NATS antenna amp. circuit is
• Inactive communication between NATS antenna
NATS ANTENNA open or shorted)
amp. and BCM.
P1614 AMP • Mechanical key
• Mechanical key is malfunctioning.
• BCM
DTC CONFIRMATION PROCEDURE

1. Insert mechanical key into the key cylinder.
2. Press the ignition knob switch.
Is DTC detected?
YES >> Refer to SEC-30, "Diagnosis Procedure".
1.CHECK NATS ANTENNA AMP. INSTALLATION

Check NATS antenna amp. installation. Refer to SEC-93, "Removal and Installation".
YES >> GO TO 2
NO >> Reinstall NATS antenna amp. correctly.
2.CHECK NVIS (NATS) IGNITION KEY ID CHIP
Start engine with another registered NATS ignition key.
Does the engine start?
YES >> • Ignition key ID chip is malfunctioning.
• Replace the ignition key.
• Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Manual”.
NO >> GO TO 3
3.CHECK POWER SUPPLY FOR NATS ANTENNA AMP.
1. Turn ignition switch ON.
2. Check voltage between NATS antenna amp. connector M21 terminal 1 and ground.
SEC-30
1 - Ground : Battery voltage A

YES >> GO TO 4
NO >> Repair or replace fuse or harness. B
LIIA1280E
4.CHECK NATS ANTENNA AMP. GROUND LINE CIRCUIT D
1. Turn ignition switch OFF.

2. Disconnect NATS antenna amp. connector.
E
3. Check continuity between NATS antenna amp. connector M21 terminal 3 and ground.
3 - Ground : Continuity should exist.

F
YES >> GO TO 5
NO >> • Repair or replace harness.
G
NOTE:
If harness is OK, replace BCM, perform initialization
with CONSULT-III. For initialization, refer to “CON-
SULT-III Operation Manual”. H
LIIA1283E
5.CHECK NATS ANTENNA AMP. SIGNAL LINE- 1 I

1. Connect NATS antenna amp. connector.
3. Check voltage between NATS antenna amp. connector M21 ter- J
minal 2 and ground with analog tester.
SEC
LIIA1281E M
Terminals Voltage (V) N

Position of ignition key cylinder
(+) (-) (Approx.)
Before inserting ignition key Battery voltage

O
Pointer of tester should move for approx. 30 seconds,
After inserting ignition key
2 Ground then return to battery voltage
Just after turning ignition switch Pointer of tester should move for approx. 1 second, then
ON return to battery voltage
P

YES >> GO TO 6
NOTE:
If harness is OK, replace BCM, perform initialization with CONSULT-III. For initialization, refer to
“CONSULT-III Operation Manual”.
SEC-31
6.CHECK NATS ANTENNA AMP. SIGNAL LINE- 2

Check voltage between NATS antenna amp. connector M21 terminal
4 and ground with analog tester.
LIIA1282E
Terminals Voltage (V)

(+) (-) (Approx.)

YES >> NATS antenna amp. is malfunctioning.
NOTE:
If harness is OK, replace BCM, refer to BCS-54, "Removal and Installation". Perform initializa-
tion with CONSULT-III. For initialization, refer to “CONSULT-III Operation Manual”.
SEC-32
B2191, P1615 DIFFERENCE OF KEY
A
Performs ID verification through BCM when ignition knob switch is pressed. B

C
DTC DETECTION LOGIC
DTC No.
Trouble diagnosis
DTC detecting condition Possible cause
D
name
B2191 DIFFERENCE OF The ID verification results between BCM and me-
Mechanical key
P1615 KEY chanical key are NG. The registration is necessary. E

1.PERFORM DTC CONFIRMATION PROCEDURE F
2. Press the ignition knob switch.
3. Check “Self diagnostic result” with CONSULT-III. G
Is DTC detected?
YES >> Refer toSEC-33, "Diagnosis Procedure".
NO >> INSPECTION END. H
I
Can the system be initialized and can the engine be started with re-registered mechanical key?
YES >> Mechanical key was unregistered.
NO >> BCM is malfunctioning. SEC
• Replace BCM. Refer to BCS-54, "Removal and Installation".
• Perform initialization again
L
SEC-33
B2192, P1611 ID DISCORD, IMMU-ECM
BCM performs the ID verification with ECM that allows the engine to start. BCM starts the communication with
ECM if ignition switch is turned ON and starts the engine if the ID is OK. ECM prevents the engine from start-
ing if the ID is not registered.
DTC DETECTION LOGIC

NOTE:
• If DTC B2192 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-25, "DTC Logic".
Trouble diagnosis
name
B2192 ID DISCORD BCM- The ID verification results between BCM and ECM • BCM
P1611 ECM are NG. The registration is necessary. • ECM

Is DTC detected?
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Manual”.
YES >> ID was unregistered.
NO >> GO TO 2
2.PEPLACE BCM
1. Replace BCM. Refer to BCS-54, "Removal and Installation".
2. Perform initialization with CONSULT-III. Re-register all mechanical keys.
YES >> BCM is malfunctioning.
NO >> GO TO 3
3.PEPLACE ECM
1. Replace ECM. Refer to Removal and Installation.
YES >> ECM is malfunctioning.
NO >> GO TO 4
4.CHECK INTERMITENT INCIDENT
Refer to GI-51, "Intermittent Incident".
SEC-34
>> INSPECTION END A
SEC
SEC-35
B2193, P1612 CHAIN OF ECM-IMMU
BCM performs the ID verification with ECM that allows the engine to start. BCM starts the communication with
DTC DETECTION LOGIC

NOTE:
Trouble diagnosis
name
(The CAN communication line is
CHAIN OF BCM-
Inactive communication between ECM and BCM open or short)
P1612 ECM
• BCM
• ECM

Is DTC detected?
NO >> INSPECTION END
1.REPLACE BCM
2. Perform initialization with CONSULT-III.
YES >> BCM was malfunctioning.
NO >> ECM is malfunctioning.
• Replace ECM.
• Perform ECM re-communicating function.
SEC-36
B2194 ID DISCORD IMMU-I-KEY
B2194 ID DISCORD IMMU-I-KEY
A
BCM performs the ID verification with Intelligent Key unit that allows the engine to start. BCM starts the com- B
munication with Intelligent Key unit if ignition switch is turned ON and starts the engine if the ID is OK. BCM
prevents the engine from starting if the ID is not registered.
DTC DETECTION LOGIC

D
Trouble diagnosis
name
The ID verification results between BCM and Intel- E
DISCORD BCM-I- • BCM
B2194 ligent Key unit are NG. The registration is neces-
KEY • Intelligent Key unit
sary.
DTC CONFIRMATION PROCEDURE F

1. Turn ignition switch ON. G
Is DTC detected?
YES >> Refer to SEC-37, "Diagnosis Procedure". H
I
Is DTC detected?
YES >> GO TO 2 SEC
NO >> ID was unregistered.
2.REPLACE BCM L
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Manual”. M
Can the system be initialized and can the engine be started?
NO >> GO TO 3 N
3.CHECK INTERMITTENT INCIDENT

Refer to GI-51, "Intermittent Incident". O
>> INSPECTION END

P
SEC-37
B2552 INTELLIGENT KEY
B2552 INTELLIGENT KEY
Intelligent key unit performs engine start operation and steering lock control by crosschecking ID with the Intel-
ligent key.
DTC DETECTION LOGIC
Trouble diagnosis
name
INTELLIGENT KEY Malfunction is detected inside Intelligent
B2552 Intelligent Key unit
UNIT key unit.

Is DTC detected?
1.REPLACE INTELLIGENT KEY UNIT

1. Replace Intelligent Key unit.
2. Perform initialization with CONSULT-III. Re-register all mechanical keys. Refer to “CONSULT-III Opera-
tion Manual”.
3. Start the engine.
YES >> INSPECTION END
NO >> Perform “DTC confirmation procedure”. Refer to SEC-38, "DTC Logic".
1.REQUIRED WORK WHEN REPLACING INTELLIGENT KEY UNIT

Initialize control unit. Refer to CONSULT-III Operation Manual.
>> Work end.
SEC-38
B2590 ID DISCORD BCM-I-KEY
B2590 ID DISCORD BCM-I-KEY
A
Intelligent Key unit performs the ID verification with BCM that allows the engine to start. BCM starts the engine B
if the ID is OK and prevents the engine from starting if the ID is not registered.
C
DTC DETECTION LOGIC
NOTE:
• If DTC B2590 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to D
E
Trouble diagnosis
name
The ID verification results between BCM and Intel- F
ID DISCORD BCM-I- • BCM
B2590 ligent Key unit are NG. The registration is neces-
KEY • Intelligent Key unit
sary.
G
1. Turn ignition switch ON. H
Is DTC detected?
YES >> Refer to SEC-39, "Diagnosis Procedure". I
J
Perform initialization with CONSULT-III. Re-register all mechanical keys. SEC
YES >> ID was unregistered. L
NO >> BCM is malfunctioning.
• Replace BCM. Refer to REMOVAL PROCEDURE.
M
SEC-39
P1610 LOCK MODE
P1610 LOCK MODE
When the starting operation is carried more than five times consecutively under the following conditions, NATS
will shift to the mode which prevents the engine from being started.
• Unregistered mechanical key is used.
• BCM or ECM's malfunctioning.
DTC DETECTION LOGIC
Trouble diagnosis
name
When the starting operation is carried out
five or more times consecutively under the
P1610 LOCK MODE following conditions. —
• Unregistered mechanical key

Is DTC detected?
1.CHECK ENGINE START FUNCTION

1. Perform the check for DTC except DTC P1610.
2. Use CONSULT-III to erase DTC after fixing.
3. Check that engine can start with registered mechanical key.
NO >> GO TO 2
>> INSPECTION END
SEC-40
POWER SUPPLY AND GROUND CIRCUIT
A
INTELLIGENT KEY UNIT
INTELLIGENT KEY UNIT : Diagnosis Procedure INFOID:0000000001689560
B
Refer to DLK-46, "INTELLIGENT KEY UNIT : Diagnosis Procedure".
BCM
C
BCM : Diagnosis Procedure INFOID:0000000001689561
Refer to BCS-32, "Diagnosis Procedure".

D
SEC
SEC-41
KEY CYLINDER SWITCH
KEY CYLINDER SWITCH
The main power window and door lock/unlock switch detects condition of the door key cylinder switch and
transmits to BCM as the LOCK or UNLOCK signal.
Component Function Check INFOID:0000000001728778
1.CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL

Check "KEY CYL LK-SW" AND "KEY CYL UN-SW" in DATA MONITOR mode for “POWER DOOR LOCK
SYSTEM” with CONSULT-III.
Monitor item Condition

Lock : ON
KEY CYL LK-SW
Neutral / Unlock : OFF
Unlock : ON
KEY CYL UN-SW
Neutral / Lock : OFF
YES >> Key cylinder switch is OK.
NO >> Refer to SEC-42, "Diagnosis Procedure".
1.CHECK DOOR KEY CYLINDER SWITCH LH

With CONSULT-III
Check front door lock assembly LH (key cylinder switch) ("KEY CYL LK-SW") and ("KEY CYL UN-SW) in
DATA MONITOR mode with CONSULT–III.
• When key inserted in left front key cylinder is turned to LOCK:
KEY CYL LK-SW : ON

• When key inserted in left front key cylinder is turned to UNLOCK:
KEY CYL UN-SW : ON
Without CONSULT-III
Check voltage between main power window and door lock/unlock
switch connector D7 terminals 4, 6 and ground.

Connector Condition of left front key cylinder
(+) (–) (Approx.)
Neutral/Unlock 5
4
Lock 0
D7 Ground
Neutral/Lock 5
6
Unlock 0 LIIA0566E

YES >> Key cylinder switch signal is OK.
NO >> GO TO 2.
2.CHECK DOOR KEY CYLINDER SWITCH LH GROUND HARNESS
2. Disconnect front door lock assembly LH (key cylinder switch).
SEC-42
KEY CYLINDER SWITCH
3. Check continuity between front door lock assembly LH (key cyl-
inder switch) connector (A) D14 terminal 4 and body ground. A
Connector Terminals Continuity

D14 4 – Ground Yes B
ALKIA1186ZZ
D
YES >> GO TO 3.
NO >> Repair or replace harness. E
Check continuity between front door lock assembly LH (key cylinder
switch) terminals. F
Terminals Condition Continuity

G
Key is turned to LOCK or neutral. No
3–4
Key is turned to UNLOCK. Yes
Key is turned to UNLOCK or neutral. No H
4–5
Key is turned to LOCK. Yes
Is the inspection result normal? ALKIA1183ZZ
I
YES >> GO TO 4.
NO >> Replace front door lock assembly LH (key cylinder switch). Refer to DLK-190, "Removal and
Installation".
J
4.CHECK DOOR KEY CYLINDER HARNESS
Check continuity between main power window and door lock/unlock
switch connector (A) D7 terminals 4, 6 and front door lock assembly SEC
LH (key cylinder switch) connector (B) D14 terminals 3, 5 and body
ground.
L
Connector Terminals Connector Terminals Continuity
4 B: Front 5 Yes
A: Main door lock
power win- M
assembly
dow and LH (key
6 3 Yes
door lock/ cylinder ALKIA1184ZZ
unlock switch)
switch
N
4, 6 Ground No
Is the inspection result normal? O

YES >> Replace main power window and door lock/unlock switch.
P
SEC-43
GLASS HATCH AJAR SWITCH
1.CHECK GLASS HATCH AJAR SWITCH INPUT SIGNAL

With CONSULT-III
Check glass hatch ajar switch ("TRNK OPN MNTR") in DATA MONITOR mode with CONSULT–III.
• When glass hatch is open:
TRNK OPN MNTR : ON

• When glass hatch is closed:
TRNK OPN MNTR : OFF
Without CONSULT-III
Check voltage between BCM connector M19 terminal 42 and ground.

Connector Item Condition
(+) (–) (Approx.)
Open 0
M19 BCM 42 Ground ↓ ↓
Closed Battery voltage
YES >> System is OK.
NO >> GO TO 2
LIIA1149E
2.CHECK GLASS HATCH AJAR SWITCH CIRCUIT

2. Disconnect BCM and glass hatch ajar switch.
3. Check continuity between BCM connector M19 terminal 42 and glass hatch ajar switch connector D503
terminal 1 (+) .
42 - 1 (+) : Continuity should exist.

4. Check continuity between glass hatch ajar switch connector
D503 terminal 1 (+) and ground.
1 (+) - Ground : Continuity should not exist.

YES >> GO TO 3
LIIA1150E
3.CHECK GLASS HATCH AJAR SWITCH

Check continuity between glass hatch ajar switch connector terminal
1 and ground.
Glass hatch ajar Open Yes

1 – Ground
switch Closed No
YES >> Check glass hatch ajar switch case ground condition.
NO >> Replace glass hatch ajar switch.
ALKIA0668ZZ
SEC-44
IGNITION KNOB SWITCH
A
Ignition Knob Switch Check INFOID:0000000001728780
1.CHECK IGNITION KNOB SWITCH B

With CONSULT-III
Display “PUSH SW” on DATA MONITOR screen, and check if ON/OFF display is linked to ignition switch oper-
ation. C

D
Ignition switch is pushed: ON
PUSH SW
Ignition switch is released: OFF
E
Without CONSULT-III
2. Disconnect Intelligent Key unit connector.
3. Check voltage between Intelligent Key unit harness connector F
M164 terminal 27 and ground.
Terminals G
Voltage (V)
Connector Condition
(+) (–) (Approx.)
Ignition switch is
Battery voltage H
pushed
M164 27 Ground
Ignition switch is re-
0
leased
I
Is the inspection result normal? WIIA1175E
YES >> Ignition knob switch is OK.

NO >> GO TO 2. J
2.CHECK IGNITION KNOB SWITCH POWER SUPPLY CIRCUIT
2. Disconnect key switch and ignition knob switch connector. SEC
3. Check voltage between key switch and ignition knob switch harness connector M66 terminal 1 and
ground.
L
1 - Ground : Battery voltage
YES >> GO TO 3. M
NO >> Repair or replace key switch and ignition knob switch
power supply circuit.
N
ALKIA1217ZZ O
3.CHECK IGNITION KNOB SWITCH OPERATION
Check continuity between key switch and ignition knob switch terminals 1 and 2.
P
SEC-45
Component Terminals Condition Continuity
Ignition Ignition switch is pushed Yes

1 2
knob switch Ignition switch is released No
YES >> GO TO 4.
NO >> Replace key switch and ignition knob switch.
ALKIA1218ZZ
4.CHECK IGNITION KNOB SWITCH CIRCUIT

1. Check continuity between Intelligent Key unit harness connector (A) M164 terminal 27 and key switch and
ignition knob switch harness connector (B) M66 terminal 2.
27 - 2 : Continuity should exist.

2. Check continuity between Intelligent Key unit harness connector
M164 terminal 27 and ground.
27 - Ground : Continuity should not exist.

YES >> Check the condition of harness and harness connector.
NO >> Repair or replace harness between Intelligent Key unit
and key switch and ignition knob switch. ALKIA1219ZZ
SEC-46
HORN FUNCTION
HORN FUNCTION
A
Symptom Table INFOID:0000000001689566
HAZARD AND HORN REMINDER FUNCTION MALFUNCTION B

NOTE:
• Before performing the diagnosis in the following table, check “Work flow”. Refer to SEC-5, "Work Flow".
• If the following symptoms” are detected, check systems shown in the “Diagnosis/service procedure” column C
in this order.
Conditions of Vehicle (Operating Conditions)
• “ANSWER BACK FUNCTION” is ON when setting on CONSULT-III. D
• Ignition switch is in OFF position.
• All doors are closed.
E
Reference
Symptom Diagnosis/service procedure
page
Check “HAZARD ANSWER BACK” setting in “WORK
1. SEC-20 F
SUPPORT”.
Hazard reminder does not operate by request switch.
(Horn reminder operate.) 2. Check hazard function. EXL-4
3. Check Intermittent Incident. GI-51
G
1. SEC-20
SUPPORT”.
Hazard reminder does not operate by Intelligent Key.
H
3. Check Intelligent Key battery inspection. DLK-87
Check “ANSWER BACK WITH I-KEY LOCK” or “AN-
1. SWER BACK WITH I-KEY UNLOCK” setting in “WORK SEC-20 I
Horn reminder does not operate by request switch. SUPPORT”.
(Hazard reminder operate.)
2. Check Intelligent Key warning buzzer. DLK-73
3. Check Intermittent Incident. GI-51 J
Check “HORN WITH KEYLESS LOCK” setting in
1. SEC-20
“WORK SUPPORT”.
Horn reminder does not operate by Intelligent Key.
(Hazard reminder operate.) 2. Check horn function. HRN-3 SEC
SEC-47
VEHICLE SECURITY INDICATOR
• Vehicle security indicator is built in combination meter.

• NATS (Nissan Anti-Theft System) and vehicle security system conditions are indicated by blink or illumina-
tion of vehicle security indicator.
1.CHECK FUNCTION
1. Perform “THEFT IND” in the “Active Test” mode with CONSULT-III.
2. Check vehicle security indicator operation.

ON ON
THEFT IND Vehicle security indicator
OFF OFF
YES >> INSPECTION END.
1.SECURITY INDICATOR LAMP ACTIVE TEST

With CONSULT-III
Check "THEFT IND” in "ACTIVE TEST" mode with CONSULT-III.
Without CONSULT-III
1. Disconnect BCM.
2. Check voltage between BCM harness connector M18 terminal
23 and ground.

Connector Condition
(+) (-) (Approx.)
ON 0
M18 23 Ground
OFF Battery voltage
YES >> Security indicator lamp is OK. LIIA0523E
NO >> GO TO 2
2.SECURITY INDICATOR LAMP CHECK
Check security indicator lamp condition.
YES >> GO TO 3
NO >> Replace security indicator lamp.
3.CHECK HARNESS CONTINUITY
2. Disconnect BCM and security indicator lamp connector.
SEC-48
3. Check continuity between BCM connector (A) M18 terminal 23
and combination meter connector (B) M24 terminal 39. A

4. Check continuity between BCM connector (A) M18 terminal 23 B
and ground.
23 - Ground : Continuity should not exist. C

YES >> Check the following: ALKIA1273ZZ
• 10A fuse [No. 19, located in fuse block (J/B)] D

• Harness for open or short between security indicator lamp and fuse
E
SEC
SEC-49
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
ECU DIAGNOSIS
Reference Value INFOID:0000000001689570
VALUES ON THE DIAGNOSIS TOOL

Refer to BCS-38, "Reference Value".
TERMINAL LAYOUT
Refer to BCS-41, "Terminal Layout".
PHYSICAL VALUES
Refer to BCS-41, "Physical Values".
SEC-50
Wiring Diagram - VEHICLE SECURITY SYSTEM INFOID:0000000001689571
SEC
ALKWA0155GB
P
SEC-51
ALKWA0156GB
SEC-52
SEC
ALKIA0462GB
SEC-53
ALKIA0463GB
SEC-54
SEC
ALKIA0464GB
SEC-55
ALKIA0465GB
SEC-56
SEC
ALKIA0466GB
SEC-57
ALKIA0467GB
SEC-58
SEC
ALKIA0937GB
SEC-59
ALKIA0938GB
SEC-60
Wiring Diagram - NVIS INFOID:0000000001689572
SEC
ALKWA0152GB
P
SEC-61
ALKWA0153GB
SEC-62
SEC
ALKWA0154GB
SEC-63
ALKIA0475GB
SEC-64
SEC
ALKIA0476GB
SEC-65
ALKIA0477GB
SEC-66
SEC
ALKIA0478GB
SEC-67
ALKIA0935GB
SEC-68
SEC
ALKIA0936GB
SEC-69
Fail Safe INFOID:0000000001689573
Display contents of CONSULT-III Fail-safe Cancellation

B2013: STRG COMM 1 • Inhibits steering look unlocking Erase DTC
• Inhibits steering look unlocking
• Inhibits engine cranking
B2552: INTELLIGENT KEY (BCM) Erase DTC
• Fuel cut
(ECM)
B2590: NATS MALFUNCTION (BCM) Erase DTC
• Fuel cut
(ECM)
DTC Inspection Priority Chart INFOID:0000000001689574
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
• U1000: CAN COMM CIRCUIT
1 • U1010: CONTROL UNIT (CAN)
• B2552: INTELLIGENT KEY
• B2013: STRG COMM 1
2
• B2590: NATS MALFUNCTION
DTC Index INFOID:0000000001689575
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
CONSULT display Detection condition Fail-safe Diagnosis

No DTC is detected.
further testing — — —
may be required.
Check CAN communi-
Intelligent Key unit cannot receive CAN communi-
U1000: CAN COMM CIRCUIT — cation system.
cation signal continuously for 2 seconds or more.
Refer to SEC-25
Intelligent Key unit detects internal CAN communi- Replace Intelligent Key
U1010: CONTROL UNIT (CAN) —
cation circuit malfunction. unit.
The ID verification result between Intelligent key
Perform steering lock
unit and steering lock solenoid are NG. Or Intelligent
B2013: STRG COMM 1 × unit ID registration with
Key unit cannot communicate with steering lock so-
CONSULT-III
lenoid.
Replace Intelligent Key
B2552: INTELLIGENT KEY Intelligent Key unit internal malfunction. ×
unit.
Check NATS
B2590: NATS MALFUNCTION unit and BCM are NG. Or Intelligent Key unit cannot ×
Refer to SEC-39
communicate with BCM.
SEC-70
A
VALUES ON THE DIAGNOSIS TOOL B

CONSULT-III MONITOR ITEM
Monitor Item Condition Value/Status
C
Release OFF
PUSH SW Ignition knob
Press ON
Removed OFF D
KEY ON SW Mechanical key
Inserted ON
Door request switch Release OFF

DR REQ SW E
(driver) Press ON

AS REQ SW
(passenger) Press ON
F
BD/TR REQ SW
(back door) Press ON
Other than ON position OFF G
IGN SW Ignition switch
ON position ON
Other than ACC or ON position OFF
ACC SW Ignition switch H
ACC or ON position ON
Press OFF
STOP LAMP SW Brake pedal
Release ON I
Lock button of Release OFF
DOOR LOCK SIG
Intelligent Key Press ON
J
Unlock button of Release OFF
DOOR UNLOCK SIG
Intelligent Key Press ON
Close OFF SEC
DOOR SW DR Door (driver side)
Open ON
Close OFF
DOOR SW AS Door (passenger side) L
Open ON
Close OFF
DOOR SW RR Door (rear RH)
Open ON
M
Close OFF
DOOR SW RL Door (rear LH)
Open ON
Close OFF N
DOOR BK SW Back door
Open ON
VEHICLE SPEED While driving Equivalent to speedometer reading
O
TERMINAL LAYOUT
Refer to DLK-129, "Reference Value - Intelligent Key Unit".
PHYSICAL VALUES P
Refer to DLK-129, "Reference Value - Intelligent Key Unit".
SEC-71
Wiring Diagram - INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION -
INFOID:0000000001689577
ALKWA0132GB
SEC-72
SEC
ALKWA0133GB
SEC-73
ALKWA0134GB
SEC-74
SEC
ALKIA0468GB
SEC-75
ALKIA0469GB
SEC-76
SEC
ALKIA0470GB
SEC-77
ALKIA0471GB
SEC-78
SEC
ALKIA0472GB
SEC-79
ALKIA0473GB
SEC-80
SEC
ALKIA0474GB
SEC-81
ALKIA0926GB
SEC-82
SEC
ALKIA0927GB
SEC-83
ALKIA0928GB
SEC-84
SEC
ALKIA0929GB
SEC-85
Fail Safe INFOID:0000000001689578
Display contents of CONSULT-III Fail-safe Cancellation

B2013: STRG COMM 1 • Inhibits steering look unlocking Erase DTC
B2552: INTELLIGENT KEY (BCM) Erase DTC
• Fuel cut
(ECM)
B2590: NATS MALFUNCTION (BCM) Erase DTC
• Fuel cut
(ECM)
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 • U1010: CONTROL UNIT (CAN)
• B2552: INTELLIGENT KEY
• B2013: STRG COMM 1
2
• B2590: NATS MALFUNCTION
NOTE:
CONSULT display Detection condition Fail-safe Diagnosis

No DTC is detected.
further testing — — —
may be required.
Check CAN communi-
Intelligent Key unit cannot receive CAN communi-
U1000: CAN COMM CIRCUIT — cation system.
cation signal continuously for 2 seconds or more.
Refer to SEC-25
Intelligent Key unit detects internal CAN communi- Replace Intelligent Key
U1010: CONTROL UNIT (CAN) —
cation circuit malfunction. unit.
Perform steering lock
unit and steering lock solenoid are NG. Or Intelligent
B2013: STRG COMM 1 × unit ID registration with
Key unit cannot communicate with steering lock so-
CONSULT-III
lenoid.
Replace Intelligent Key
B2552: INTELLIGENT KEY Intelligent Key unit internal malfunction. ×
unit.
Check NATS
B2590: NATS MALFUNCTION unit and BCM are NG. Or Intelligent Key unit cannot ×
Refer to SEC-39
communicate with BCM.
SEC-86
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
A
ROOM)
B
Refer to PCS-17, "Reference Value".
C
TERMINAL LAYOUT
Refer to PCS-19, "Terminal Layout".
Fail Safe INFOID:0000000001689582 D
Refer to PCS-26, "Fail Safe".

E
Refer to PCS-28, "DTC Index".

F
SEC
SEC-87
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION SYMPTOMS
< SYMPTOM DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
SYMPTOM DIAGNOSIS
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION SYMPTOMS
NOTE:
• Before performing the diagnosis in the following table, check “SEC-5, "Work Flow"”.
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
• Engine cranking is enabled when the shift lever is in the "Park" position, and in the "Neutral" position only if
the brake pedal is depressed.
• If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
• Engine start function is ON when setting on CONSULT-III.
• Mechanical key is not inserted in key cylinder.
• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Reference
page
Ignition switch does not turn on with Intelligent Key. 1. Check steering lock solenoid. SEC-27
[green "KEY" lamp is displayed] 2. Replace Intelligent Key unit. SEC-93
1. Check Intelligent Key unit power supply and ground circuit. DLK-46
2. Check ignition knob switch. DLK-97
3. Check key switch (BCM input). DLK-96
Ignition switch does not turn on with Intelligent Key.
4. Check key switch (Intelligent Key unit input). DLK-94
["KEY" lamp does not display]
5. Replace Intelligent Key unit. SEC-93
6. Check green "KEY" indicator. DLK-76
7. Check red "KEY" indicator. DLK-76
1a. Check inside key antenna 1 (instrument panel). DLK-40
Ignition switch does not turn on with Intelligent Key. 1b. Check inside key antenna 2 (luggage compartment). DLK-42
[red "KEY" lamp is displayed] 1c. Check inside key antenna 3 (center console). DLK-44
2. Replace Intelligent Key unit. SEC-93
1. Check key switch (BCM input). DLK-96
Ignition switch does not turn on with mechanical key
2. Check key switch (Intelligent Key unit input). DLK-94
Engine cannot be cranked with transmission in "Park" 1. Check transmission signal. TM-50
or in "Neutral" position with brake pedal depressed 2. Check stop lamp switch. EXL-81
"P-SHIFT" indicator does not operate properly 1. Check "P-SHIFT" indicator. DLK-76
SEC-88
VEHICLE SECURITY SYSTEM SYMPTOMS
A
B
Procedure
Diagnostic procedure Refer to page
Symptom
Door switch Check door switch (LF, RF, LR, RR, back) DLK-48 C
Glass ajar switch Check glass ajar switch SEC-44
Vehicle security sys-
tem cannot be set by Intelligent Key Check Intelligent Key system SEC-9
···· D
1 Key cylinder switch Check key cylinder switch SEC-42
— Check Intermittent Incident GI-51
Check vehicle security indicator SEC-48 E
Security indicator does not turn ON.
Check Intermittent Incident GI-51
Any door is opened. Check door switch (LF, RF, LR, RR, back) DLK-48
* Vehicle security
2 system does not Glass ajar switch Check glass ajar switch SEC-44
F
sound alarm when ····
Vehicle security Check horn switch HRN-3
G
3 alarm does not acti- Horn alarm
vate. Check Intermittent Incident GI-51
Intelligent Key Check Intelligent Key system SEC-9

Vehicle security sys- H
4 tem cannot be can- Key cylinder switch Check key cylinder switch SEC-42
celed by ····
*: Check the system is in the armed phase. I
SEC
SEC-89
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS SYMPTOMS
NOTE:
check each symptom.
• If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
• Mechanical key is not inserted into key cylinder.
• Ignition knob switch is not depressed.
Symptom Diagnosis/service procedure Reference page

1. Check vehicle security indicator SEC-48
Security indicator does not turn ON or flash.
2. Check Intermittent Incident GI-51
SEC-90
PRE-INSPECTION FOR DIAGNOSTIC
< ON-VEHICLE MAINTENANCE > [WITH INTELLIGENT KEY SYSTEM]
ON-VEHICLE MAINTENANCE A
Basic Inspection INFOID:0000000001689587
B
The engine start function, door lock function, power distribution system and NATS-IVIS/NMS in the Intelligent
Key system are closely related to each other regarding control. Narrow down the functional area in question
by performing basic inspection to identify which function is malfunctioning. The vehicle security function can C
operate only when the door lock and power distribution system are operating normally. Therefore, it is easy to
identify any factor unique to the vehicle security system by performing the vehicle security operation check
after basic inspection. D
1.CHECK DOOR LOCK OPERATION
1. Check the door lock for normal operation with the Intelligent Key controller and door request switch.
Successful door lock operation with the Intelligent Key and request SW indicates that the remote keyless E
entry receiver and inside key antenna required for engine start are functioning normally.
Identify the malfunctioning point by referring to the DLK section if the door cannot be unlocked.
Can the door be locked with the Intelligent Key and door request switch? F
YES >> GO TO 2.
NO >> Refer to DLK-160, "Symptom Table".
2.CHECK ENGINE STARTING G
1. Checks that the engine starts when operating the Intelligent Key.
Does the engine start? H
YES >> GO TO 3.
NO >> Refer to SEC-88, "Symptom Table".
3.CHECK STEERING LOCKING I
1. Does the steering lock when operating door switch after switching the power supply from ON position (or
ACC position) to LOCK position?
If door switch is malfunctioning, BCM cannot lock the steering. If BCM does not detect DTC, steering lock J
unit is normal.
Does steering lock?
YES >> GO TO 4. SEC
NO >> Refer to DLK-80, "Diagnosis Procedure".
4.CHECK POWER SUPPLY INDICATOR SWITCHING
L
1. Press push-button ignition switch and position indicator will switch from LOCK, ACC to ON gradually
when steering is locked. Checks that the position indicator is illuminated at different positions of the circuit.
Is each position indicator illuminating?
M
YES >> GO TO 5.
NO >> Refer to SEC-45, "Ignition Knob Switch Check".
5.CHECK VEHICLE SECURITY SYSTEM N
1. Check the vehicle security system for normal operation.
The vehicle security function can operate only when the door lock and power distribution functions are
operating normally. O
Therefore, it is easy to identify any factor unique to the vehicle security by performing the vehicle security
operation check after this basic inspection.
P
>> Go to SEC-91, "Vehicle Security Operation Check".
Vehicle Security Operation Check INFOID:0000000001689588
1.INSPECTION START
Turn ignition switch “OFF”.
NOTE:
SEC-91
< ON-VEHICLE MAINTENANCE > [WITH INTELLIGENT KEY SYSTEM]
Before starting operation check, open front windows.
>> GO TO 2.
2.CHECK SECURITY INDICATOR LAMP
1. Lock doors using Intelligent Key or mechanical key.
2. Check that security indicator lamp illuminates for 30 seconds.
Security indicator lamp should illuminate.
OK >> GO TO 3.
NG >> Perform diagnosis and repair. Refer to SEC-48, "Diagnosis Procedure".
3.CHECK ALARM FUNCTION
1. After 30 seconds, security indicator lamp will start to blink.
2. Open any door before unlocking with Intelligent Key or mechanical key, or open back door or glass hatch
without the presence of Intelligent Key.
Does the alarm function properly?
YES >> GO TO 4.
NO >> Check the following.
• The vehicle security system does not phase in alarm mode. Refer to SEC-88, "Symptom Table".
• Alarm (horn and headlamps) does not operate. Refer to SEC-88, "Symptom Table".
4.CHECK ALARM CANCEL OPERATION
Unlock any door using Intelligent Key or mechanical key.
Alarm (horn and headlamps) should stop.
OK >> INSPECTION END.
NG >> Check door lock function. Refer to SEC-89, "Symptom Table".
SEC-92
< ON-VEHICLE REPAIR > [WITH INTELLIGENT KEY SYSTEM]
ON-VEHICLE REPAIR A
Removal and Installation INFOID:0000000001689589
B
REMOTE KEYLESS ENTRY RECEIVER

Removal C
1. Remove the instrument panel. Refer to IP-10, "Removal and Installation".
2. Disconnect the wire harness (1), remove the bolt (A) and the
RKE receiver (2). D
ALKIA0537ZZ
G
Installation
Installation is in the reverse order of removal.
INTELLIGENT KEY UNIT H
Removal
I
2. Disconnect the wire harness (1), remove the bolt (A) and the
Intelligent key unit (2).
J
SEC
L
ALKIA0666ZZ
Installation
Installation is in the reverse order of removal. M
SEC-93
NATS ANTENNA AMP.
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
REMOVAL AND INSTALLATION

NATS ANTENNA AMP.
NOTE:
• If NATS antenna amp. is not installed correctly, NVIS (NATS) system will not operate properly and "SELF-
DIAG RESULTS' on CONSULT-III screen will show "LOCK MODE" or "CHAIN OF IMMU-KEY'.
• Initilization is not necessary when only the NATS antenna amp. is replaced with a new one.
REMOVAL
1. Disconnect the battery negative terminal.
2. Remove cluster lid A. Refer to IP-10, "Exploded View".
3. Remove the bolt, disconnect the electrical connector, and remove the NATS antenna amp.
INSTALLATION
SEC-94
A
REMOVAL B
2. Remove the lower glove box. Refer to IP-10, "Exploded View".
C
3. Remove the bolt (A), disconnect the electrical connector (1), and
remove the intelligent key module (2).
⇒: Front D
F
ALKIA1059ZZ
INSTALLATION
Installation is in the reverse order of removal. G
SEC
SEC-95
Removal INFOID:0000000001730844
1. Disconnect the battery negative cable.

2. Remove the upper glove box. Refer to IP-10, "Exploded View".
3. Remove the bolt, disconnect and remove the remote keyless entry receiver.
Installation INFOID:0000000001730845
SEC-96
< BASIC INSPECTION > [WITHOUT INTELLIGENT KEY SYSTEM]
BASIC INSPECTION A
Work Flow INFOID:0000000001689590
B
OVERALL SEQUENCE
C
SEC
ALKIA0538GB
DETAILED FLOW
SEC-97
1.GET INFORMATION FOR SYMPTOM

Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2.CHECK DTC
1. Check DTC for Intelligent Key unit and BCM.
2. Perform the following procedure if DTC is displayed.
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real-time diagnosis results.
>> GO TO 5.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real-time diagnosis results.
>> GO TO 6.
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to SEC-144, "DTC Inspection Priority Chart" (BCM) and determine
trouble diagnosis order.
Is DTC detected?
YES >> GO TO 8.
6.PERFORM BASIC INSPECTION
Perform Basic Inspection. Refer to SEC-91, "Basic Inspection".
>> GO TO 7.
7.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to Symptom Table based on the confirmed symptom in step 4.
>> GO TO 8.
8.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure is described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
>> GO TO 9.
SEC-98
9.REPAIR OR REPLACE THE MALFUNCTIONING PART A

1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
B
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 10.
C
10.FINAL CHECK
When DTC was detected in step 9, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunctions have been fully repaired. D
When symptom was described by the customer, refer to the confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear? E
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO >> INSPECTION END F
SEC
SEC-99
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement INFOID:0000000001689591
Refer to the CONSULT-III Operation Manual-NATS.

ECM RE-COMMUNICATING FUNCTION
ECM RE-COMMUNICATING FUNCTION : Description INFOID:0000000001689592
Performing following procedure can automatically perform re-communication of ECM and BCM, but only when
the ECM has been replaced with a new one (*1).
*1: New one means an ECM which has never been energized on-board.
(In this step, initialization procedure by CONSULT-III is not necessary)
NOTE:
• When registering new Key IDs or replacing the ECM that is not brand new, refer to CONSULT-III Oper-
ation Manual NATS.
• If multiple keys are attached to the key holder, separate them before work.
• Distinguish keys with unregistered key ID from those with registered ID.
ECM RE-COMMUNICATING FUNCTION : Special Repair Requirement INFOID:0000000001689593
1.PERFORM ECM RE-COMMUNICATING FUNCTION

1. Install ECM.
2. Using a registered key (*2), turn ignition switch to “ON”.
*2: To perform this step, use the key that has been used before performing ECM replacement.
3. Maintain ignition switch in “ON” position for at least 5 seconds.
4. Turn ignition switch to “OFF”.
5. Start engine.
Can engine be started?
YES >> Procedure is completed.
NO >> Initialize control unit. Refer to CONSULT-III Operation Manual NATS.
SEC-100
< FUNCTION DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
FUNCTION DIAGNOSIS A
B
G
PIIA1121E
System Description INFOID:0000000001689595 H
INPUT/OUTPUT SIGNAL CHART

I
BCM
Switch/Input signal Input signal to BCM BCM function Actuator/Output signal J

NATS antenna amp. Key ID • Security indicator lamp
NATS
ECM Engine status signal • Starter request
SEC
SYSTEM DESCRIPTION
NATS (Nissan Anti-Theft System) has the following immobilizer functions:
• Engine immobilizer shows high anti-theft performance to prevent engine from starting by other than the L
owner.
• Only a key with key ID registered in BCM and ECM can start engine, and shows high anti-theft performance
to prevent key from being copied or stolen.
• Security indicator always flashes with mechanical key removed condition (key switch: OFF) and ignition M
knob released condition on LOCK position (ignition knob switch: OFF).
• Therefore, NATS warns outsiders that the vehicle is equipped with the anti-theft system. Refer to SEC-104,
"System Description". N
• If system detects malfunction, security indicator illuminates when ignition switch is turned to ON position.
• If the owner requires, ignition key ID or mechanical key ID can be registered for up to 5 keys.
• During trouble diagnosis or when the following parts have been replaced, and if ignition key is added, regis-
tration* is required. O
*1
: All keys kept by the owner of the vehicle should be registered with mechanical key.
- ECM
- BCM P
- Ignition key
- Remote keyless entry receiver
• NATS trouble diagnosis, system initialization and additional registration of other mechanical key IDs must be
carried out using CONSULT-III.
When NATS initialization has been completed, the ID of the inserted mechanical key or mechanical key IDs
can be carried out.
SEC-101
• Possible symptom of NATS malfunction is “Engine cannot start”. Identify the possible causes according to
“Work Flow”, Refer to SEC-97, "Work Flow".
• If ECM other than Genuine NISSAN is installed, the engine cannot be started. For ECM replacement proce-
dure, refer to SEC-100, "ECM RE-COMMUNICATING FUNCTION : Description".
PRECAUTIONS FOR KEY REGISTRATION
• The key registration is a procedure that erases the current NATS ID once, and then re-registers a new ID.
Therefore the registered key is necessary for this procedure. Before starting the registration operation collect
all registered Keys from the customer.
• The NATS ID registration is the procedure that registers the ID stored into the transponder (integrated in
mechanical key) to BCM.
The key ID registration is the procedure that registers the ID to the BCM.
• When performing the key system registration only, the engine cannot be started by inserting the key into the
key cylinder. When performing the NATS registration only, the engine cannot be started by using the ignition
key.
SECURITY INDICATOR
• Always flashes with ignition key in the OFF position.
MAINTENANCE INFORMATION
CAUTION:
It is necessary to perform NATS ID registration when replacing any of the following part.
If it's not (or fail to do so), the electrical system may not operate properly.
• BCM
• ECM
• IPDM E/R
• Ignition key
• Combination meter
ALKIA1271ZZ
SEC-102
1. BCM M18, M20 2. NATS antenna amp. M21 3. ECM E16 A

(view with instrument panel LH re-
moved)
4. IPDM E/R E119, E120, E122, E124 5. Combination meter M24 6. Security indicator lamp
(view with cover removed) B
C
Item Function
BCM Verifies the received signal from the ignition key ID, then informs ECM whether to allow engine start. D
Remote keyless entry receiver Receives lock/unlock signal from the keyfob, and then transmits to the BCM.
NATS antenna amp. Detects the ignition key presence in the ignition key cylinder. E
IPDM E/R Powers-up the horn and the headlamps in case of a security breach.
F
SEC
SEC-103
ALKIA0706GB
DESCRIPTION
The security system provides an audible and visual alarm when an unauthorized access to the vehicle is
detected while the system is in armed phase.
The security system consist of the BCM managing the audible alarm (horn) and the visual alarm (headlamps).
OPERATION FLOW
PIIA1367E
Disarmed Phase
When the vehicle is being driven or when doors are open, the theft warning system is set in the disarmed
phase on the assumption that the owner is inside or near the vehicle.
Pre-Armed Phase And Armed Phase
The vehicle security system turns into the pre-armed phase when ignition switch is in OFF position, all doors
are closed and locked (using keyfob, doorlock/unlock switch, driver key cylinder or auto relock function). The
system automatically shifts into the armed phase.
Condition of Activating The System
When the following condition is performed in armed phase, the system sounds the horns and flashes the
headlamps for about 30 seconds.
• Any door is opened.
SEC-104
Condition of Deactivating The System
When one of the following operations is performed, the armed phase is canceled. A
• Unlock the doors with keyfob.
• Use the mechanical key to unlock the driver door using the door key cylinder.
Component Parts Location INFOID:0000000001728844 B
SEC
ALKIA1270ZZ M
1. BCM M18, M19, M20 2. IPDM E/R E122, E123, E124 3. Horn relay H-1
(view with instrument panel LH re- (view with cover removed)
N
moved)
4. Main power window and door lock/ 5. Front door switch LH B8 6. Front door lock assembly LH (key cylin-
unlock switch D7, D8 RH B108 der switch) D14
7. Power window and door lock/unlock 8. Rear door switch LH B18 9. Back door cinching latch unit (door ajar O
switch RH D105 RH B116 switch) D502
Glass hatch ajar switch D503
10. Horn E3 11. Combination meter M24 12. Security indicator lamp P
(behind front combination lamp LH)
SEC-105
Item Function
BCM Verifies the received signal from ignition key, then informs ECM whether to allow engine start.
Door switch Provides the BCM with the status of each monitored door.
IPDM E/R Controls the horn and headlamps operation.
Horn Sounds when the vehicle security system is triggered.
SEC-106
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001689602
B
APPLICATION ITEM
C
D
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to SEC-70, "DTC Index".
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed. E
ECU IDENTIFICATION The BCM part number is displayed.
• Enables to read and save the vehicle specification. F
CONFIGURATION
• Enables to write the vehicle specification when replacing BCM.
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
H
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
I
— BCM ×
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × × J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
SEC
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × × L
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITONER ×
Combination switch COMB SW × M
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
N
Vehicle security system THEFT ALM × × ×
IMMU
O
IMMU : CONSULT-III Function (BCM - IMMU) INFOID:0000000001689603
APPLICATION ITEM P

DATA MONITOR
SEC-107
Monitor item Content

ACTIVE TEST

THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT ALM) INFOID:0000000001689604
APPLICATION ITEM

DATA MONITOR
Monitor Item Condition

ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW Indicates [ON/OFF] condition of door lock and unlock switch.
CDL UNLOCK SW Indicates [ON/OFF] condition of door lock and unlock switch.
ACTIVE TEST

VEHICLE SECURITY HORN This test is able to check horn operation [ON].
FLASHER This test is able to check flasher operation [LH/RH/OFF].
WORK SUPPORT

Vehicle security function mode can be changed in this mode.
SECURITY ALARM SET • ON: Vehicle security function is ON.
• OFF: Vehicle security function is OFF.
The switch which triggered vehicle security system is recorded. This mode can be able to con-
THEFT ALM TRG
firm and erase the record of vehicle security system.
SEC-108
< COMPONENT DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
COMPONENT DIAGNOSIS A
B
vehicle is equipped with many electronic control unit, and each control unit shares information and links with C
wiring. Each control unit transmits/receives data but selectively reads required data only. D
CAN Communication Signal Chart, refer to .LAN-57, "CAN Communication Signal Chart"
E
DTC DETECTION LOGIC
CONSULT-III display F
description
In CAN communication system, any item (or items)
of the following listed below is malfunctioning. G
When BCM cannot communicate CAN com- • Receiving (TCM)
U1000 CAN COMM CIRCUIT munication signal continuously for 2 sec- • Receiving (IPDM E/R)
onds or more. • Receiving (ECM)
• Receiving (METER/M&A) H
• Receiving (MULTI AV)

I
1.PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more. J
2. Check “Self Diagnostic Result”.
Is “CAN COMM CIRCUIT” displayed?
YES >> Refer to LAN-5, "CAN Communication Control Circuit". SEC
SEC-109
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
wiring. Each control unit transmits/receives data but selectively reads required data only.
DTC DETECTION LOGIC
CONSULT-III display de-

scription
When detecting error during the initial diagnosis of CAN control-
U1010 CONTROL UNIT (CAN) BCM
ler of BCM.
1.REPLACE BCM
When DTC [U1010] is detected, replace BCM.
>> Replace BCM. Refer to BCS-54, "Removal and Installation".

1.REQUIRED WORK WHEN REPLACING BCM

Initialize BCM. Refer to CONSULT-III Operation Manual.
>> Work end.
SEC-110
A
Performs ID verification through BCM and NATS antenna amplifier when ignition key is inserted and ignition B
switch turned ON.
Prohibits the start of engine when an unregistered ID of ignition key is used.
DTC DETECTION LOGIC

D
Trouble diagnosis
name
B2190 • Harness or connectors E
(The NATS antenna amp. circuit is
• Inactive communication between NATS antenna
NATS ANTENNA open or shorted)
amp. and BCM.
P1614 AMP • Ignition key
• Ignition key is malfunctioning.
• NATS antenna amp. F
• BCM

G
1. Insert ignition key into the key cylinder.
2. Turn ignition switch ON. H
Is DTC detected?
YES >> Refer to SEC-111, "Diagnosis Procedure". I
J
1.CHECK NATS ANTENNA AMP. INSTALLATION
Check NATS antenna amp. installation. Refer to SEC-149, "Removal and Installation".
SEC
YES >> GO TO 2
NO >> Reinstall NATS antenna amp. correctly. L
2.CHECK NVIS (NATS) IGNITION KEY ID CHIP
Start engine with another registered NATS ignition key.
Does the engine start? M
YES >> • Ignition key ID chip is malfunctioning.
• Replace the ignition key.
• Perform initialization with CONSULT-III. N
NO >> GO TO 3
3.CHECK POWER SUPPLY FOR NATS ANTENNA AMP. O
2. Check voltage between NATS antenna amp. connector M21 terminal 1 and ground.
P
SEC-111
1 - Ground : Battery voltage

YES >> GO TO 4
NO >> Repair or replace fuse or harness.
LIIA1280E
4.CHECK NATS ANTENNA AMP. GROUND LINE CIRCUIT

2. Disconnect NATS antenna amp. connector.
3. Check continuity between NATS antenna amp. connector M21 terminal 3 and ground.
3 - Ground : Continuity should exist.

YES >> GO TO 5
NOTE:
If harness is OK, replace BCM, perform initialization
with CONSULT-III. For initialization, refer to “CON-
SULT-III Operation Manual”.
LIIA1283E
5.CHECK NATS ANTENNA AMP. SIGNAL LINE- 1

1. Connect NATS antenna amp. connector.
3. Check voltage between NATS antenna amp. connector M21 ter-
minal 2 and ground with analog tester.
LIIA1281E

(+) (-) (Approx.)

YES >> GO TO 6
NOTE:
If harness is OK, replace BCM, perform initialization with CONSULT-III. For initialization, refer to
“CONSULT-III Operation Manual”.
SEC-112
6.CHECK NATS ANTENNA AMP. SIGNAL LINE- 2 A

Check voltage between NATS antenna amp. connector M21 terminal
4 and ground with analog tester.
B
D
LIIA1282E
E
(+) (-) (Approx.)

F
G
H
YES >> NATS antenna amp. is malfunctioning.
NOTE:
If harness is OK, replace BCM, refer to XX-XX, "*****". Perform initialization with CONSULT-III. I
SEC
SEC-113
Performs ID verification through BCM when ignition knob switch is pressed.

DTC DETECTION LOGIC
Trouble diagnosis
name
B2191 DIFFERENCE OF The ID verification results between BCM and me-
Mechanical key
P1615 KEY chanical key are NG. The registration is necessary.

Is DTC detected?
YES >> Refer toSEC-114, "Diagnosis Procedure".
YES >> Mechanical key was unregistered.
NO >> BCM is malfunctioning.
• Replace BCM. Refer to BCS-54, "Removal and Installation".
SEC-114
A
BCM performs the ID verification with ECM that allows the engine to start. BCM starts the communication with B
DTC DETECTION LOGIC

NOTE: D
E
Trouble diagnosis
name F
B2192 ID DISCORD BCM- The ID verification results between BCM and ECM • BCM
P1611 ECM are NG. The registration is necessary. • ECM
G
H
Is DTC detected?
I
Diagnosis Procedure INFOID:0000000001689620 J
Perform initialization with CONSULT-III. Re-register all mechanical keys. SEC
YES >> ID was unregistered. L
NO >> GO TO 2
2.PEPLACE BCM M
N
NO >> GO TO 3
O
3.PEPLACE ECM
1. Replace ECM. Refer to Removal and Installation.
2. Perform initialization with CONSULT-III. Re-register all mechanical keys. P
YES >> ECM is malfunctioning.
NO >> GO TO 4
4.CHECK INTERMITENT INCIDENT
SEC-115
>> INSPECTION END
SEC-116
A
BCM performs the ID verification with ECM that allows the engine to start. BCM starts the communication with B
DTC DETECTION LOGIC

NOTE: D
E
Trouble diagnosis
name F
(The CAN communication line is
CHAIN OF BCM-
Inactive communication between ECM and BCM open or short) G
P1612 ECM
• BCM
• ECM
DTC CONFIRMATION PROCEDURE H

1. Turn ignition switch ON. I
Is DTC detected?
YES >> Refer to SEC-117, "Diagnosis Procedure". J
SEC
1.REPLACE BCM
2. Perform initialization with CONSULT-III. L
YES >> BCM was malfunctioning. M
NO >> ECM is malfunctioning.
• Replace ECM.
• Perform ECM re-communicating function. N
SEC-117
P1610 LOCK MODE
P1610 LOCK MODE
When the starting operation is carried more than five times consecutively under the following conditions, NATS
will shift to the mode which prevents the engine from being started.
• Unregistered mechanical key is used.
DTC DETECTION LOGIC
Trouble diagnosis
name
When the starting operation is carried out
five or more times consecutively under the
P1610 LOCK MODE following conditions. —
• Unregistered mechanical key

Is DTC detected?
1.CHECK ENGINE START FUNCTION

1. Perform the check for DTC except DTC P1610.
2. Use CONSULT-III to erase DTC after fixing.
3. Check that engine can start with registered mechanical key.
NO >> GO TO 2
>> INSPECTION END
SEC-118
A
BCM
BCM : Diagnosis Procedure INFOID:0000000001689627
B
Refer to BCS-32, "Diagnosis Procedure".
SEC
SEC-119
KEY CYLINDER SWITCH
KEY CYLINDER SWITCH
The main power window and door lock/unlock switch detects condition of the door key cylinder switch and
transmits to BCM as the LOCK or UNLOCK signal.
1.CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL

Check "KEY CYL LK-SW" AND "KEY CYL UN-SW" in DATA MONITOR mode for “POWER DOOR LOCK
SYSTEM” with CONSULT-III.

Lock : ON
KEY CYL LK-SW
Neutral / Unlock : OFF
Unlock : ON
KEY CYL UN-SW
Neutral / Lock : OFF
YES >> Key cylinder switch is OK.

With CONSULT-III
Check front door lock assembly LH (key cylinder switch) ("KEY CYL LK-SW") and ("KEY CYL UN-SW) in
DATA MONITOR mode with CONSULT–III.
• When key inserted in left front key cylinder is turned to LOCK:
KEY CYL LK-SW : ON

• When key inserted in left front key cylinder is turned to UNLOCK:
KEY CYL UN-SW : ON
Without CONSULT-III
Check voltage between main power window and door lock/unlock
switch connector D7 terminals 4, 6 and ground.

Connector Condition of left front key cylinder
(+) (–) (Approx.)
Neutral/Unlock 5
4
Lock 0
D7 Ground
Neutral/Lock 5
6
Unlock 0 LIIA0566E

YES >> Key cylinder switch signal is OK.
NO >> GO TO 2.
2.CHECK DOOR KEY CYLINDER SWITCH LH GROUND HARNESS
2. Disconnect front door lock assembly LH (key cylinder switch).
SEC-120
KEY CYLINDER SWITCH
3. Check continuity between front door lock assembly LH (key cyl-
inder switch) connector (A) D14 terminal 4 and body ground. A
Connector Terminals Continuity

D14 4 – Ground Yes B
ALKIA1186ZZ
D
YES >> GO TO 3.
NO >> Repair or replace harness. E
Check continuity between front door lock assembly LH (key cylinder
switch) terminals. F

G
Key is turned to LOCK or neutral. No
3–4
Key is turned to UNLOCK. Yes
Key is turned to UNLOCK or neutral. No H
4–5
Key is turned to LOCK. Yes
Is the inspection result normal? ALKIA1183ZZ
I
YES >> GO TO 4.
NO >> Replace front door lock assembly LH (key cylinder switch). Refer to DLK-313, "Removal and
Installation".
J
4.CHECK DOOR KEY CYLINDER HARNESS
Check continuity between main power window and door lock/unlock
switch connector (A) D7 terminals 4, 6 and front door lock assembly SEC
LH (key cylinder switch) connector (B) D14 terminals 3, 5 and body
ground.
L
Connector Terminals Connector Terminals Continuity
4 B: Front 5 Yes
A: Main door lock
power win- M
assembly
dow and LH (key
6 3 Yes
door lock/ cylinder ALKIA1184ZZ
unlock switch)
switch
N
4, 6 Ground No
Is the inspection result normal? O

YES >> Replace main power window and door lock/unlock switch.
P
SEC-121
1.CHECK GLASS HATCH AJAR SWITCH INPUT SIGNAL

With CONSULT-III
Check glass hatch ajar switch ("TRNK OPN MNTR") in DATA MONITOR mode with CONSULT–III.
• When glass hatch is open:
TRNK OPN MNTR : ON

• When glass hatch is closed:
TRNK OPN MNTR : OFF
Without CONSULT-III
Check voltage between BCM connector M19 terminal 42 and ground.

Connector Item Condition
(+) (–) (Approx.)
Open 0
M19 BCM 42 Ground ↓ ↓
Closed Battery voltage
YES >> System is OK.
NO >> GO TO 2
LIIA1149E
2.CHECK GLASS HATCH AJAR SWITCH CIRCUIT

2. Disconnect BCM and glass hatch ajar switch.
3. Check continuity between BCM connector M19 terminal 42 and glass hatch ajar switch connector D503
terminal 1 (+) .
42 - 1 (+) : Continuity should exist.

4. Check continuity between glass hatch ajar switch connector
D503 terminal 1 (+) and ground.
1 (+) - Ground : Continuity should not exist.

YES >> GO TO 3
LIIA1150E
3.CHECK GLASS HATCH AJAR SWITCH

Check continuity between glass hatch ajar switch connector terminal
1 and ground.
Glass hatch ajar Open Yes

1 – Ground
switch Closed No
YES >> Check glass hatch ajar switch case ground condition.
NO >> Replace glass hatch ajar switch.
ALKIA0668ZZ
SEC-122
HORN FUNCTION
HORN FUNCTION
A
HAZARD AND HORN REMINDER FUNCTION MALFUNCTION B

NOTE:
• Before performing the diagnosis in the following table, check “Work flow”. Refer to SEC-97, "Work Flow".
• If the following symptoms” are detected, check systems shown in the “Diagnosis/service procedure” column C
in this order.
Conditions of Vehicle (Operating Conditions)
• “ANSWER BACK FUNCTION” is ON when setting on CONSULT-III. D
• Ignition switch is in OFF position.
• All doors are closed.
E
Reference
page
1. SEC-107 F
SUPPORT”.
Hazard reminder does not operate by key fob.
3. Check key fob battery inspection. DLK-234
G
Check “HORN WITH KEYLESS LOCK” setting in
1. SEC-107
“WORK SUPPORT”.
Horn reminder does not operate by key fob.
(Hazard reminder operate.) 2. Check horn function. HRN-3
H
SEC
SEC-123
• Vehicle security indicator is built in combination meter.

• NATS (Nissan Anti-Theft System) and vehicle security system conditions are indicated by blink or illumina-
tion of vehicle security indicator.
1.CHECK FUNCTION
1. Perform “THEFT IND” in the “Active Test” mode with CONSULT-III.
2. Check vehicle security indicator operation.

ON ON
THEFT IND Vehicle security indicator
OFF OFF
YES >> INSPECTION END.
1.SECURITY INDICATOR LAMP ACTIVE TEST

With CONSULT-III
Check "THEFT IND” in "ACTIVE TEST" mode with CONSULT-III.
Without CONSULT-III
1. Disconnect BCM.
2. Check voltage between BCM harness connector M18 terminal
23 and ground.

Connector Condition
(+) (-) (Approx.)
ON 0
M18 23 Ground
OFF Battery voltage
YES >> Security indicator lamp is OK. LIIA0523E
NO >> GO TO 2
2.SECURITY INDICATOR LAMP CHECK
Check security indicator lamp condition.
YES >> GO TO 3
NO >> Replace security indicator lamp.
3.CHECK HARNESS CONTINUITY
2. Disconnect BCM and security indicator lamp connector.
SEC-124
3. Check continuity between BCM connector (A) M18 terminal 23
and combination meter connector (B) M24 terminal 39. A

4. Check continuity between BCM connector (A) M18 terminal 23 B
and ground.
23 - Ground : Continuity should not exist. C

YES >> Check the following: ALKIA1273ZZ
• 10A fuse [No. 19, located in fuse block (J/B)] D

• Harness for open or short between security indicator lamp and fuse
E
SEC
SEC-125
< ECU DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
ECU DIAGNOSIS

Refer to BCS-38, "Reference Value".
TERMINAL LAYOUT
Refer to BCS-41, "Terminal Layout".
PHYSICAL VALUES
Refer to BCS-41, "Physical Values".
SEC-126
Wiring Diagram - VEHICLE SECURITY SYSTEM INFOID:0000000001728851
SEC
ALKWA0155GB
P
SEC-127
ALKWA0156GB
SEC-128
SEC
ALKIA0462GB
SEC-129
ALKIA0463GB
SEC-130
SEC
ALKIA0464GB
SEC-131
ALKIA0465GB
SEC-132
SEC
ALKIA0466GB
SEC-133
ALKIA0467GB
SEC-134
SEC
ALKIA0937GB
SEC-135
ALKIA0938GB
SEC-136
Wiring Diagram - NVIS - INFOID:0000000001689637
SEC
ALKWA0135GB
P
SEC-137
ALKWA0136GB
SEC-138
SEC
ALKIA0930GB
SEC-139
ALKIA0931GB
SEC-140
SEC
ALKIA0932GB
SEC-141
ALKIA0933GB
SEC-142
SEC
ALKIA0934GB
SEC-143
Priority DTC
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERNCE OF KEY
2
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
NOTE:
• PAST: Displays when there is a malfunction that is detected in the past and stored.
CONSULT display TIME Fail-safe Refer to

No DTC is detected.
further testing — — — —
may be required.
U1000: CAN COMM CIRCUIT 0 1 - 39 — SEC-109
U1010: CONTROL UNIT (CAN) 0 1 - 39 — SEC-110
B2190: NATS ANTENNA AMP CRNT PAST × SEC-111
B2191: DIFFERENCE OF KEY CRNT PAST × SEC-114
B2192: ID DISCORD BCM-ECM CRNT PAST × SEC-115
B2193: CHAIN OF BCM-ECM CRNT PAST × SEC-117
SEC-144
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
A
ROOM)
B
Refer to PCS-17, "Reference Value".
C
TERMINAL LAYOUT
Refer to PCS-19, "Terminal Layout".
Fail Safe INFOID:0000000001689642 D
Refer to PCS-26, "Fail Safe".

E
Refer to PCS-28, "DTC Index".

F
SEC
SEC-145
< SYMPTOM DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
SYMPTOM DIAGNOSIS
Procedure
Diagnostic procedure Refer to page
Symptom
Door switch Check door switch (LF, RF, LR, RR, back) DLK-214
Vehicle security sys- Glass ajar switch Check glass hatch ajar switch SEC-122
tem cannot be set by
···· Key cylinder switch Check key cylinder switch DLK-221
1
Check vehicle security indicator SEC-124
Security indicator does not turn ON.
Check Intermittent Incident GI-51
Any door is opened. Check door switch (LF, RF, LR, RR, back) DLK-214
* Vehicle security
2 system does not Glass ajar switch Check glass hatch ajar switch SEC-122
sound alarm when ····
Vehicle security Check horn switch HRN-3
3 alarm does not acti- Horn alarm
vate. Check Intermittent Incident GI-51
Vehicle security sys- Check key cylinder switch SEC-120

4 tem cannot be can- Key cylinder switch
celed by ···· Check Intermittent Incident GI-51
*: Check the system is in the armed phase.
SEC-146
< SYMPTOM DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
A
NOTE: B
check each symptom.
• If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column C
in this order.
D
• Mechanical key is not inserted into key cylinder.
• Ignition knob switch is not depressed.
Symptom Diagnosis/service procedure Reference page E

1. Check vehicle security indicator SEC-124
Security indicator does not turn ON or flash.
2. Check Intermittent Incident GI-51
F
SEC
SEC-147
< ON-VEHICLE MAINTENANCE > [WITHOUT INTELLIGENT KEY SYSTEM]
ON-VEHICLE MAINTENANCE
Basic Inspection INFOID:0000000001689646
1.INSPECTION START
Turn ignition switch “OFF”.
NOTE:
Before starting operation check, open front windows.
>> GO TO 2.
2.CHECK SECURITY INDICATOR LAMP
1. Lock doors using keyfob or mechanical key.
2. Check that security indicator lamp illuminates for 30 seconds.
Does the security indicator lamp illuminate?
YES >> GO TO 3.
NO >> Perform diagnosis and repair. Refer to SEC-104, "System Description".
3.CHECK ALARM FUNCTION
1. After 30 seconds, security indicator lamp will start to blink.
2. Open any door before unlocking with keyfob or mechanical key, or open back door or glass hatch without
keyfob.
Does the alarm function properly?
YES >> GO TO 4.
NO >> Check the following.
• The vehicle security system does not phase in alarm mode. Refer to SEC-146, "Symptom
Table".
• Alarm (horn and headlamps) does not operate. Refer to SEC-146, "Symptom Table".
4.CHECK ALARM CANCEL OPERATION
Unlock any door using keyfob or mechanical key.
Alarm (horn and headlamps) should stop.
OK >> INSPECTION END.
NG >> Check door lock function. Refer to DLK-199, "DOOR LOCK AND UNLOCK SWITCH : System
Description".
SEC-148
< ON-VEHICLE REPAIR > [WITHOUT INTELLIGENT KEY SYSTEM]
ON-VEHICLE REPAIR A
B

Removal C
2. Disconnect the wire harness (1), remove the bolt (A), and the
RKE receiver (2). D
ALKIA0537ZZ
G
Installation
NATS ANTENNA AMP H
NOTE:
DIAG RESULTS" on CONSULT -III screen will show "LOCK MODE" or "CHAIN OF IMMU-KEY" I
Removal
1. Disconnect the battery negative terminal. J
2. Remove the steering column covers. Refer to IP-10, "Exploded View".
3. Remove the bolt, disconnect the electrical connector, and
remove the NATS antenna amp. SEC
SIIA1683E
N
Installation
O
SEC-149
NATS ANTENNA AMP.
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
REMOVAL AND INSTALLATION

NATS ANTENNA AMP.
NOTE:
DIAG RESULTS' on CONSULT-III screen will show "LOCK MODE" or "CHAIN OF IMMU-KEY'.
REMOVAL
2. Remove cluster lid A. Refer to IP-10, "Exploded View".
3. Remove the bolt, disconnect the electrical connector, and remove the NATS antenna amp.
INSTALLATION
SEC-150
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
A
Removal INFOID:0000000001730846
1. Disconnect the battery negative cable. B

2. Remove the upper glove box. Refer to IP-10, "Exploded View".
3. Remove the bolt, disconnect and remove the remote keyless entry receiver.
C
Installation INFOID:0000000001730847

D
SEC
SEC-151

Security Control System: Section

Uploaded by

Copyright:

Available Formats

Security Control System: Section

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Security Control System: Section

Uploaded by

Copyright:

Available Formats

BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY

INSPECTION AND ADJUSTMENT ..................... 8 THEFT ALM ...............................................................21 H

ECU DIAGNOSIS ........................................ 50 BASIC INSPECTION .................................. 97

HORN FUNCTION ........................................... 123 I

1.GET INFORMATION FOR SYMPTOM

9.REPAIR OR REPLACE THE MALFUNCTIONING PART A

Refer to the CONSULT-III Operation Manual-NATS.

1.PERFORM ECM RE-COMMUNICATING FUNCTION

INPUT/OUTPUT SIGNAL CHART H

Component Description INFOID:0000000001689512

System Description INFOID:0000000001689514

• Intelligent Key unit

Component Description INFOID:0000000001689516

System Description INFOID:0000000001689518

Diagnosis mode Function Description

Diagnosis mode Function Description

PUSH SW Indicates [ON/OFF] condition of ignition knob switch.

Test item Description

Diagnosis mode Function Description

Monitor Item Condition I

Test item Description

Diagnosis mode Function Description C

Take away warning chime (from window) ON Active

Door lock function with Intelligent Key can be ON Active I

Buzzer reminder operation (unlock operation) BUZZER Active M

Auto door lock operation mode can be OFF Inactive

Engine start function (by Intelligent Key) ON Active

Door lock function by door request switch can ON Active

Monitor Item Condition

Test item Description

Diagnosis Procedure INFOID:0000000001689527

DTC DETECTION LOGIC

CONSULT-III display de-

Diagnosis Procedure INFOID:0000000001689530

1.REPLACE INTELLIGENT KEY UNIT

1.REQUIRED WORK WHEN REPLACING INTELLIGENT KEY UNIT

>> Work end.

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE F

2.CHECK STEERING LOCK SOLENOID POWER SUPPLY-1

NO >> Repair or replace harness. P

NO >> Repair or replace harness.

M65 terminals 2, 3 and ground.

Ignition knob is pushed G

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.CHECK NATS ANTENNA AMP. INSTALLATION

1 - Ground : Battery voltage A

4.CHECK NATS ANTENNA AMP. GROUND LINE CIRCUIT D

1. Turn ignition switch OFF.

3 - Ground : Continuity should exist.

5.CHECK NATS ANTENNA AMP. SIGNAL LINE- 1 I

Terminals Voltage (V) N

Before inserting ignition key Battery voltage

Is the inspection result normal?

6.CHECK NATS ANTENNA AMP. SIGNAL LINE- 2

Terminals Voltage (V)

Before inserting ignition key Battery voltage