Power Window Control System: Section
Power Window Control System: Section
Power Window Control System: Section
E
CONTENTS
BASIC INSPECTION .................................... 4 REAR POWER WINDOW SWITCH ...........................16 F
REAR POWER WINDOW SWITCH : Description....16
DIAGNOSIS AND REPAIR WORKFLOW .......... 4 REAR POWER WINDOW SWITCH : Component
Work Flow ................................................................. 4 Function Check ........................................................16 G
REAR POWER WINDOW SWITCH : Diagnosis
FUNCTION DIAGNOSIS ............................... 5 Procedure ................................................................16
REAR POWER WINDOW SWITCH : Component
POWER WINDOW SYSTEM ............................... 5 H
Inspection ................................................................18
System Diagram ....................................................... 5
System Description ................................................... 5 POWER WINDOW MOTOR .............................. 19
Component Parts Location ...................................... 7 I
Component Description ............................................. 7 DRIVER SIDE .............................................................19
DRIVER SIDE : Description .....................................19
DIAGNOSIS SYSTEM (BCM) ............................. 9 DRIVER SIDE : Component Function Check ..........19
DRIVER SIDE : Diagnosis Procedure .....................19 J
COMMON ITEM ........................................................... 9
DRIVER SIDE : Component Inspection ...................20
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ....................................................... 9 PASSENGER SIDE ....................................................20 PWC
PASSENGER SIDE : Description ............................20
RETAINED PWR ......................................................... 9
PASSENGER SIDE : Component Function Check
RETAINED PWR : CONSULT-III Function (BCM -
....20
RETAINED PWR) ..................................................... 9 L
PASSENGER SIDE : Diagnosis Procedure ............20
COMPONENT DIAGNOSIS ......................... 10 PASSENGER SIDE : Component Inspection ..........21
PWC-1
PASSENGER SIDE ................................................... 28 Diagnosis Procedure ............................................... 57
PASSENGER SIDE : Description ........................... 28
PASSENGER SIDE : Component Function Check FRONT PASSENGER SIDE POWER WIN-
... 28 DOW ALONE DOES NOT OPERATE ............... 58
PASSENGER SIDE : Diagnosis Procedure ........... 28 Diagnosis Procedure ............................................... 58
POWER WINDOW SERIAL LINK ..................... 37 ANTI-PINCH SYSTEM DOES NOT OPERATE
NORMALLY (PASSENGER SIDE) ................... 62
POWER WINDOW MAIN SWITCH ........................... 37 Diagnosis Procedure ............................................... 62
POWER WINDOW MAIN SWITCH : Description ... 37
POWER WINDOW MAIN SWITCH : Component AUTO OPERATION DOES NOT OPERATE
Function Check ....................................................... 37 BUT MANUAL OPERATE NORMALLY
POWER WINDOW MAIN SWITCH : Diagnosis (DRIVER SIDE) .................................................. 63
Procedure ............................................................... 37 Diagnosis Procedure ............................................... 63
FRONT POWER WINDOW SWITCH ........................ 38 AUTO OPERATION DOES NOT OPERATE
FRONT POWER WINDOW SWITCH : Descrip- BUT MANUAL OPERATE NORMALLY (PAS-
tion .......................................................................... 38 SENGER SIDE) ................................................. 64
FRONT POWER WINDOW SWITCH : Compo- Diagnosis Procedure ............................................... 64
nent Function Check ............................................... 38
FRONT POWER WINDOW SWITCH : Diagnosis POWER WINDOW RETAINED POWER OP-
Procedure ............................................................... 39 ERATION DOES NOT OPERATE PROPERLY
POWER WINDOW LOCK SWITCH ................... 41 ... 65
Diagnosis Procedure ............................................... 65
Description .............................................................. 41
Component Function Check ................................... 41 DOES NOT OPERATE BY KEY CYLINDER
ECU DIAGNOSIS ........................................ 42 SWITCH ............................................................. 66
Diagnosis Procedure ............................................... 66
BCM (BODY CONTROL MODULE) .................. 42
Reference Value ..................................................... 42
KEYLESS POWER WINDOW DOWN DOES
NOT OPERATE ................................................. 67
POWER WINDOW MAIN SWITCH .................... 43 Diagnosis Procedure ............................................... 67
Reference Value ..................................................... 43
Wiring Diagram ....................................................... 45 POWER WINDOW LOCK SWITCH DOES
Fail Safe ................................................................. 52 NOT FUNCTION ................................................ 68
Diagnosis Procedure ............................................... 68
FRONT POWER WINDOW SWITCH ................ 54
Reference Value ..................................................... 54 PRECAUTION ............................................ 69
Wiring Diagram ....................................................... 55
Fail Safe ................................................................. 55
PRECAUTIONS ................................................. 69
Precaution for Supplemental Restraint System
SYMPTOM DIAGNOSIS ............................. 56 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................. 69
NONE OF THE POWER WINDOWS CAN BE
OPERATED USING ANY SWITCH ................... 56 ON-VEHICLE REPAIR ............................... 70
Diagnosis Procedure .............................................. 56
POWER WINDOW MAIN SWITCH ................... 70
DRIVER SIDE POWER WINDOW ALONE Removal and Installation ......................................... 70
DOES NOT OPERATE ...................................... 57
PWC-2
FRONT POWER WINDOW SWITCH .................71 REAR POWER WINDOW SWITCH .................. 72
Removal and Installation ......................................... 71 Removal and Installation - Rear Door Switch ..........72 A
PWC
PWC-3
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000001702334
DETAILED FLOW
1. OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
>> GO TO 2
2. REPRODUCE THE MALFUNCTION INFORMATION
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 3
3. IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the symptom inspection result in step 2 and then identify where to start per-
forming the diagnosis based on possible causes and symptoms.
>> GO TO 4
4. IDENTIFY THE MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component diagnosis” of the applicable system.
>> GO TO 5
5. REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 6
6. FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Are the malfunctions corrected?
YES >> INSPECTION END
NO >> GO TO 3
PWC-4
POWER WINDOW SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS A
POWER WINDOW SYSTEM
System Diagram INFOID:0000000001702335
B
ALCIA0038GB
J
PWC
POWER WINDOW MAIN SWITCH
INPUT/OUTPUT SIGNAL CHART
L
Input signal to main power window and Main power window and door
Item Actuator
door lock/unlock switch lock/unlock switch function
LOCK/UNLOCK signal (more than 1.5
Key cylinder switch M
seconds over)
Encoder Encoder pulse signal
Main power window
and door lock/unlock
Front power window motor LH UP/ N
DOWN signal Front power window motor
switch
Power window control
Power window and
Front power window motor RH UP/ O
door lock/unlock
DOWN signal
switch RH
BCM RAP signal
Rear power window Rear power window motor UP/DOWN P
Rear power window motor
switch signal
PWC-5
POWER WINDOW SYSTEM
< FUNCTION DIAGNOSIS >
PWC-6
POWER WINDOW SYSTEM
< FUNCTION DIAGNOSIS >
• Hold door key cylinder to LOCK position for more than 1 second to perform CLOSE operation of the door
glass. A
• Hold door key cylinder to UNLOCK position for more than 1 second to perform OPEN operation of the door
glass.
KEYLESS POWER WINDOW DOWN OPERATION (FRONT LH & RH) B
Front power windows open when the unlock button on Intelligent Key or keyfob is activated and kept pressed
for more than 3(NOTE) seconds with the ignition switch OFF. The windows keep opening if the unlock button is
continuously pressed. C
The power window opening stops when the following operations are performed:
• When the unlock button is kept pressed more than 15 seconds.
• When the ignition switch is turned ON while the power window opening is operated.
D
• When the unlock button is released.
While retained power operation activate, keyless power window down function cannot be operated.
NOTE:
Keyless power window down operation mode can be changed by “PW DOWN SET” mode in “WORK SUP- E
PORT”. Refer to DLK-36, "CONSULT-III Function (INTELLIGENT KEY)" with Intelligent Key or DLK-208,
"REMOTE KEYLESS ENTRY : CONSULT-III Function (BCM - RKE)" with remote keyless entry system.
NOTE:
F
Use CONSULT-III to change settings.
MODE1 (3sec)/MODE2 (OFF)/MODE3 (5sec)
Component Parts Location INFOID:0000000001702337 G
PWC
LIIA2390E
O
1. Main power window and door lock/ 2. BCM M18, M19, M20 (view with in- 3. Power window and door lock/unlock
unlock switch D7, D8 strument lower panel LH removed) switch RH D105
4. Front power window motor LH D9, 5. Front door switch LH B8, RH B108 6. A. Rear power window switch LH P
RH D104 D203, RH D303
B. Rear power window motor LH
D204, RH D304
PWC-7
POWER WINDOW SYSTEM
< FUNCTION DIAGNOSIS >
Component Function
• Supplies power supply to power window switch.
BCM
• Controls retained power.
Main power window and door lock/un- • Directly controls all power window motor of all doors.
lock switch • Controls anti-pinch operation of front power window LH.
Power window and door lock/unlock • Controls front power window motor RH.
switch RH • Controls anti-pinch operation of front power window RH.
Rear power window switch • Controls rear power window motors LH and RH.
• Integrates the ENCODER POWER and WINDOW MOTOR.
• Starts operating with signals from main power window and door lock/unlock switch.
Front power window motor LH
• Transmits power window motor rotation as a pulse signal to main power window and
door lock/unlock switch.
Starts operating with signals from main power window and door lock/unlock switch &
Front power window motor RH
power window and door lock/unlock switch RH.
Starts operating with signals from main power window and door lock/unlock switch &
Rear power window motor
rear power window switch.
Front door lock assembly LH (key cylin-
Transmits operation condition of key cylinder switch to power window main switch.
der switch)
Front door switch LH or RH Detects door open/close condition and transmits to BCM.
PWC-8
DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001702339
B
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
D
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to BCS-51, "DTC Index".
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed. E
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
CONFIGURATION This function is not used even though it is displayed. F
SYSTEM APPLICATION
BCM can perform the following functions for each system. G
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
H
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
BCM BCM × I
RAP system RETAINED PWR ×
RETAINED PWR
J
RETAINED PWR : CONSULT-III Function (BCM - RETAINED PWR) INFOID:0000000001702340
PWC-9
POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Description INFOID:0000000001702341
Main Power Window And Door Lock/Unlock Switch Power Supply Circuit Check
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/
unlock switch connectors (A and B) and ground.
Terminal
(+)
Voltage (V)
Main power window and (–) (Approx.)
door lock/unlock switch Terminal
connector
D7 (A) 10 ALKIA0273ZZ
Ground Battery voltage
D8 (B) 19
Is the measurement value within the specification?
YES >> GO TO 3
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM and main power window and door lock/unlock
switch.
3. Check continuity between BCM connector (A) and main power
window and door lock/unlock switch connectors (B and C).
PWC-10
POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
Terminals
Voltage (V)
(+) J
(–) (Approx.)
BCM connector Terminal
68
M20 Ground Battery voltage PWC
69
LIIA0917E
Is the measurement value within the specification?
YES >> Check main power window and door lock/unlock switch output signal (rear power window switch L
LH) GO TO 5
YES >> Check main power window and door lock/unlock switch output signal (rear power window switch
RH) GO TO 6
NO >> Replace BCM. Refer to BCS-54, "Removal and Installation". M
5. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL (REAR POW-
ER WINDOW SWITCH LH)
N
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/
unlock switch connector and ground.
O
ALKIA0276ZZ
PWC-11
POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
Terminal
(+)
Window Voltage (V)
Main power window (–) condition (Approx.)
and door lock/unlock Terminal
switch connector
UP Battery voltage
1
DOWN 0
D7 Ground
UP 0
3
DOWN Battery voltage
Is the measurement value within the specification?
YES >> GO TO 7
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-70, "Removal and Instal-
lation".
6. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL (REAR POW-
ER WINDOW SWITCH RH)
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/
unlock switch connector and ground.
Terminal
(+)
Window Voltage (V)
Main power win-
(–) condition (Approx.)
dow and door
Terminal
lock/unlock
switch connector
ALKIA0277ZZ
UP Battery voltage
7
DOWN 0
D7 Ground
UP 0
5
DOWN Battery voltage
Is the measurement value within the specification?
YES >> GO TO 8
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-70, "Removal and Instal-
lation".
7. CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH LH)
1. Turn ignition switch OFF.
2. Disconnect rear power window switch LH.
3. Check continuity between main power window and door lock/
unlock switch connector and rear power window switch LH con-
nector.
PWC-12
POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
PWC-13
POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
2. Check continuity between main power window and door lock/
unlock switch (power window lock switch). (Lock operation).
Power Window And Door Lock/Unlock Switch RH Power Supply Circuit Check
1. CHECK POWER SUPPLY CIRCUIT
PWC-14
POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
1. Turn ignition switch ON.
2. Check voltage between power window and door lock/unlock A
switch RH connector and ground.
Terminal B
(+)
Voltage (V)
Power window and door lock/ (–) (Approx.)
unlock Terminal C
switch RH connector
D105 10 Ground Battery voltage ALKIA0301ZZ
PWC-15
POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector and ground.
Terminals
Voltage (V)
(+)
(-) (Approx.)
BCM connector Terminal
M20 69 Ground Battery voltage
Is the measurement value within the specification?
WIIA0508E
YES >> Replace power window and door lock/unlock switch RH.
Refer to PWC-71, "Removal and Installation".
NO >> Replace BCM. Refer to BCS-54, "Removal and Installation".
REAR POWER WINDOW SWITCH
REAR POWER WINDOW SWITCH : Description INFOID:0000000001702348
Terminal
(+) Voltage (V)
Condition
(–) (Approx.)
Rear power window
Terminal
switch connector
LH D203 Ignition switch
8 Ground Battery voltage
RH D303 ON
LIIA1715E
Is the measurement value within the specification?
YES >> GO TO 2 (Rear power window switch LH)
YES >> GO TO 3 (Rear power window switch RH)
NO >> GO TO 4
2. CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH LH)
PWC-16
POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch and A
rear power window switch LH.
3. Check continuity between main power window and door lock/
unlock switch connector (A) and rear power window switch LH
B
connector (B).
PWC-17
POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
1. Disconnect BCM and rear power window switch.
2. Check continuity between BCM connector (A) and rear power
window switch connector (B).
COMPONENT INSPECTION
1.CHECK REAR POWER WINDOW SWITCH
Check rear power window switch.
PWC-18
POWER WINDOW MOTOR
< COMPONENT DIAGNOSIS >
POWER WINDOW MOTOR
A
DRIVER SIDE
DRIVER SIDE : Description INFOID:0000000001702352
B
Door glass moves UP/DOWN by receiving the signal from power window main switch.
DRIVER SIDE : Component Function Check INFOID:0000000001702353
C
1. CHECK POWER WINDOW MOTOR CIRCUIT
Does front power window motor LH operate with operating main power window and door lock/unlock switch? D
Is the inspection result normal?
YES >> Front power window motor LH is OK.
NO >> Refer to PWC-19, "DRIVER SIDE : Diagnosis Procedure". E
DRIVER SIDE : Diagnosis Procedure INFOID:0000000001702354
1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL
1. Disconnect front power window motor LH. G
2. Turn ignition switch ON.
3. Check voltage between front power window motor LH connector
and ground.
H
Terminal
Main power win-
(+) I
dow and door lock/ Voltage (V)
Power window (–) unlock switch con- (Approx.)
motor LH con- Terminal dition
nector
ALKIA1207ZZ J
UP Battery voltage
2
DOWN 0
D9 Ground
UP 0 PWC
1
DOWN Battery voltage
Is the measurement value within the specification?
L
YES >> GO TO 2
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-70, "Removal and Instal-
lation".
M
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch and N
front power window motor LH.
3. Check continuity between main power window and door lock/
unlock switch connector (A) and front power window motor con-
nector LH (B). O
PWC-19
POWER WINDOW MOTOR
< COMPONENT DIAGNOSIS >
COMPONENT INSPECTION
1. CHECK FRONT POWER WINDOW MOTOR LH
Does motor operate by connecting the battery voltage directly to power window motor?
Terminal
Motor condition
(+) (–)
1 2 DOWN
2 1 UP
Is the inspection result normal?
YES >> Front power window motor LH is OK.
NO >> Replace front power window motor LH. Refer to GW-14, "Front Door Glass Regulator".
PASSENGER SIDE
PASSENGER SIDE : Description INFOID:0000000001702356
Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or
power window and door lock/unlock switch RH.
PASSENGER SIDE : Component Function Check INFOID:0000000001702357
PWC-20
POWER WINDOW MOTOR
< COMPONENT DIAGNOSIS >
1. Disconnect front power window motor RH.
2. Turn ignition switch ON. A
3. Check voltage between front power window motor RH connector
and ground.
B
Terminal
Front power
(+) Voltage (V)
window motor
(–) (Approx.) C
Front power window RH condition
Terminal
motor RH connector
UP Battery voltage ALKIA1207ZZ
2
DOWN 0 D
D104 Ground
UP 0
1
DOWN Battery voltage
E
Is the measurement value within the specification?
YES >> GO TO 2
NO >> Replace power window and door lock/unlock switch RH. Refer to PWC-71, "Removal and Installa- F
tion".
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF. G
2. Disconnect power window and door lock/unlock switch RH.
3. Check continuity between power window and door lock/unlock
switch RH connector (A) and front power window motor RH con- H
nector (B).
COMPONENT INSPECTION
1. CHECK FRONT POWER WINDOW MOTOR RH
Does motor operate by connecting the battery voltage directly to front power window motor RH?
PWC-21
POWER WINDOW MOTOR
< COMPONENT DIAGNOSIS >
Terminal
Motor condition
(+) (–)
1 2 DOWN
2 1 UP
Is the inspection result normal?
YES >> Front power window motor RH is OK.
NO >> Replace front power window motor RH. Refer to GW-14, "Front Door Glass Regulator".
REAR LH
REAR LH : Description INFOID:0000000001702360
Door glass moves UP/DOWN by receiving the signal from power window main switch or rear power window
switch LH.
REAR LH : Component Function Check INFOID:0000000001702361
Terminal
(+) Window Voltage (V)
(–) condition (Approx.)
Rear power window
Terminal
motor LH connector
UP Battery voltage LIIA2228E
1
DOWN 0
D204 Ground
UP 0
2
DOWN Battery voltage
Is the measurement value within the specification?
YES >> GO TO 2
NO >> Check rear power window switch LH. Refer to PWC-16, "REAR POWER WINDOW SWITCH :
Component Function Check".
2. CHECK HARNESS CONTINUITY
PWC-22
POWER WINDOW MOTOR
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect rear power window switch LH. A
3. Check continuity between rear power window switch LH connec-
tor (A) and rear power window motor LH connector (B).
B
Rear power window Rear power window
Terminal Terminal Continuity
switch LH connector motor LH connector
6 1 C
D203 (A) D204 (B) Yes
7 2
4. Check continuity between rear power window switch LH connec- LIIA2229E
J
COMPONENT INSPECTION
1. CHECK REAR POWER WINDOW MOTOR LH
Does motor operate by connecting the battery voltage directly to rear power window motor LH? PWC
Terminal
Motor condition L
(+) (–)
2 1 DOWN
1 2 UP M
Is the inspection result normal?
YES >> Rear power window motor LH is OK.
NO >> Replace rear power window motor LH. Refer to GW-18, "Rear Door Glass Regulator". N
REAR RH
REAR RH : Description INFOID:0000000001702364 O
Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or
rear power window switch RH.
P
REAR RH : Component Function Check INFOID:0000000001702365
PWC-23
POWER WINDOW MOTOR
< COMPONENT DIAGNOSIS >
YES >> Rear power window motor RH is OK.
NO >> Refer to PWC-24, "REAR RH : Diagnosis Procedure".
REAR RH : Diagnosis Procedure INFOID:0000000001702366
Terminal
Rear power
(+) Voltage (V)
window switch
(–) (Approx.)
Rear power window RH condition
Terminal
motor RH connector
UP Battery voltage LIIA2228E
1
DOWN 0
D304 Ground
UP 0
2
DOWN Battery voltage
Is the measurement value within the specification?
YES >> GO TO 2
NO >> Check rear power window switch RH. Refer to PWC-16, "REAR POWER WINDOW SWITCH :
Component Function Check".
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect rear power window switch RH.
3. Check continuity between rear power window switch RH con-
nector (A) and rear power window motor RH connector (B).
PWC-24
POWER WINDOW MOTOR
< COMPONENT DIAGNOSIS >
REAR RH : Component Inspection INFOID:0000000001702367
A
COMPONENT INSPECTION
1. CHECK REAR POWER WINDOW MOTOR RH B
Does motor operate by connecting the battery voltage directly to rear power window motor RH?
Terminal C
Motor condition
(+) (–)
2 1 DOWN
D
1 2 UP
Is the inspection result normal?
YES >> Rear power window motor RH is OK. E
NO >> Replace rear power window motor RH. Refer to GW-18, "Rear Door Glass Regulator".
PWC
PWC-25
ENCODER
< COMPONENT DIAGNOSIS >
ENCODER
DRIVER SIDE
DRIVER SIDE : Description INFOID:0000000001702368
Detects condition of the front power window motor LH operation and transmits to main power window and door
lock/unlock switch as pulse signal.
DRIVER SIDE : Component Function Check INFOID:0000000001702369
Terminals
(+)
Signal
Main power window (–) (Reference value)
and door lock/unlock Terminal
switch connector
9 ALKIA0295ZZ
D7 Ground Refer to following signal
13
JMKIA0220GB
PWC-26
ENCODER
< COMPONENT DIAGNOSIS >
1. Turn ignition switch ON.
2. Check voltage between front power window motor LH connector A
and ground.
Terminal B
(+)
Voltage (V)
Front power win- (–) (Approx.)
dow motor LH con- Terminal C
nector
D9 3 Ground 10 LIIA2782E
4. Check continuity between main power window and door lock/unlock switch connector (A) and ground. I
NO >> GO TO 5 P
5. CHECK HARNESS CONTINUITY 2
PWC-27
ENCODER
< COMPONENT DIAGNOSIS >
1. Disconnect main power window and door lock/unlock switch.
2. Check continuity between main power window and door lock/
unlock switch connector and front power window motor LH con-
nector.
Detects condition of the front power window motor RH operation and transmits to power window and door
lock/unlock switch RH as pulse signal.
PASSENGER SIDE : Component Function Check INFOID:0000000001702372
PWC-28
ENCODER
< COMPONENT DIAGNOSIS >
1. Turn ignition switch ON.
2. Check signal between power window and door lock/unlock A
switch RH connector and ground with oscilloscope.
Terminals B
(+)
Signal
Power window and door (–) (Reference value)
lock/unlock switch RH Terminal C
connector
12 Refer to following ALKIA0322ZZ
D105 Ground
15 signal D
G
ALKIA0305GB
4. Check continuity between power window and door lock/unlock switch RH connector (A) and ground.
PWC-29
ENCODER
< COMPONENT DIAGNOSIS >
NO >> GO TO 5
5. CHECK HARNESS CONTINUITY 2
1. Disconnect power window and door lock/unlock switch RH.
2. Check continuity between power window and door lock/unlock
switch RH connector and front power window motor RH connec-
tor.
PWC-30
ENCODER
< COMPONENT DIAGNOSIS >
PWC
PWC-31
DOOR SWITCH
< COMPONENT DIAGNOSIS >
DOOR SWITCH
Description INFOID:0000000001702374
Terminals
(+) Voltage (V)
Door condition
(–) (Approx.)
BCM
Terminal
connector
ground.
PWC-32
DOOR SWITCH
< COMPONENT DIAGNOSIS >
Terminal E
Voltage (V)
(+)
(–) (Approx.)
BCM connector Terminal
F
M18 12
Ground Battery voltage
M19 47
Is the measurement value within the specification? LIIA0946E
G
YES >> GO TO 4
NO >> Replace BCM. Refer to BCS-54, "Removal and Installation".
4. CHECK FRONT DOOR SWITCH H
L
Terminal
Door switch Continuity
Door switches
PWC-33
DOOR KEY CYLINDER SWITCH
< COMPONENT DIAGNOSIS >
DOOR KEY CYLINDER SWITCH
Description INFOID:0000000001702378
Main power window and door lock/unlock switch detects condition of the door key cylinder and transmits to
BCM as the LOCK or UNLOCK signals.
Component Function Check INFOID:0000000001702379
Terminals
(+)
Voltage (V)
Key position
Main power window (–) (Approx.)
and door lock/unlock Terminal
switch connector
Lock 0 ALKIA0309ZZ
4
Neutral/Unlock 5
D7 Ground
Unlock 0
6
Neutral/Lock 5
Is the measurement value within the specification?
YES >> Replace main power window and door lock/unlock switch.
NO >> GO TO 2
2. CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT
PWC-34
DOOR KEY CYLINDER SWITCH
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch and A
front door lock assembly LH (key cylinder switch).
3. Check continuity between main power window and door lock/
unlock switch connector (A) and front door lock assembly LH
B
(key cylinder switch) connector (B).
COMPONENT INSPECTION
1. CHECK DOOR KEY CYLINDER SWITCH O
PWC-35
DOOR KEY CYLINDER SWITCH
< COMPONENT DIAGNOSIS >
Check front door lock assembly LH (key cylinder switch).
Terminal
Front door lock assembly LH Key position Continuity
(key cylinder switch) connector
Unlock Yes
5
Neutral/Lock No
4
Lock Yes
3
Neutral/Unlock No
LIIA2807E
PWC-36
POWER WINDOW SERIAL LINK
< COMPONENT DIAGNOSIS >
POWER WINDOW SERIAL LINK
A
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Description INFOID:0000000001702382
B
Main power window and door lock/unlock switch, power window and door lock/unlock switch RH and BCM
transmit and receive the signal by power window serial link.
The signal mentioned below is transmitted from BCM to main power window and door lock/unlock switch and C
power window and door lock/unlock switch RH
• Keyless power window down signal
The signal mentioned below is transmitted from main power window and door lock/unlock switch to power win-
dow and door lock/unlock switch RH D
• Front door window RH operation signal
• Power window control by key cylinder switch signal
• Power window lock switch signal E
• Retained power operation signal
POWER WINDOW MAIN SWITCH : Component Function Check INFOID:0000000001702383
F
1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL
Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYS-
TEM” with CONSULT-III. Refer to BCS-16, "COMMON ITEM : CONSULT-III Function (BCM - COMMON G
ITEM)".
J
Is the inspection result normal?
YES >> Power window serial link is OK.
NO >> Refer to PWC-37, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure". PWC
POWER WINDOW MAIN SWITCH : Diagnosis Procedure INFOID:0000000001702384
LIIA0391E P
PWC-37
POWER WINDOW SERIAL LINK
< COMPONENT DIAGNOSIS >
Terminal
Signal
(+)
(–) (Reference value)
BCM connector Terminal
M18 22 Ground
PIIA2344E
ALKIA1026ZZ
Main power window and door lock/unlock switch, power window and door lock/unlock switch RH and BCM
transmit and receive the signal by power window serial link.
The signal mentioned below is transmitted from BCM to main power window and door lock/unlock switch and
power window and door lock/unlock switch RH
• Keyless power window down signal
The signal mentioned below is transmitted from main power window and door lock/unlock switch to power win-
dow and door lock/unlock switch RH
• Front door window RH operation signal
• Power window control by key cylinder switch signal
• Retained power operation signal
• Power window lock switch signal
FRONT POWER WINDOW SWITCH : Component Function Check INFOID:0000000001702386
PWC-38
POWER WINDOW SERIAL LINK
< COMPONENT DIAGNOSIS >
Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYS-
TEM” with CONSULT-III. Refer to BCS-17, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)". A
1. Remove Intelligent Key or ignition key, and close the front door
LH and RH.
2. Check signal between BCM connector and ground with oscillo- G
scope when door lock and unlock switch (LH and RH) is turned
to “LOCK” or “UNLOCK”.
3. Check that signals which are shown in the figure below can be H
detected during 10 second just after door lock and unlock switch
(LH and RH) is turned to “LOCK” or “UNLOCK”.
I
Terminal
Signal LIIA0391E
(+)
(–) (Reference value)
BCM connector Terminal J
PWC
M18 2 Ground
L
PIIA2344E
ALKIA1027ZZ
PWC-39
POWER WINDOW SERIAL LINK
< COMPONENT DIAGNOSIS >
PWC-40
POWER WINDOW LOCK SWITCH
< COMPONENT DIAGNOSIS >
POWER WINDOW LOCK SWITCH
A
Description INFOID:0000000001702388
Ground circuit of main power window and door lock/unlock switch shuts off if power window lock switch of B
main power window and door lock/unlock switch is operated. This inhibits all operation, except for the main
switch.
Component Function Check INFOID:0000000001702389 C
PWC
PWC-41
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000001702400
TERMINAL LAYOUT
Refer to BCS-41, "Terminal Layout".
PHYSICAL VALUES
Refer to BCS-41, "Physical Values".
PWC-42
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
POWER WINDOW MAIN SWITCH
A
Reference Value INFOID:0000000001702401
TERMINAL LAYOUT B
LIIA2455E E
PHYSICAL VALUES
F
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Terminal No. G
Description
(Wire color) Voltage [V]
Condition
Input/ (Approx.)
+ – Signal name
Output H
When rear LH switch in
1 Rear power window motor LH
Ground Output power window main switch Battery voltage
(R/Y) UP signal
is operated UP.
I
2
Ground Encoder ground — — 0
(BR)
When rear LH switch in J
3 Rear power window motor LH
Ground Output power window main switch Battery voltage
(LG) DOWN signal
is operated DOWN.
4 Door key cylinder switch LH Key position
Ground Input 5→0 PWC
(SB) LOCK signal (Neutral → Locked)
When rear RH switch in
5 Rear power window motor RH
Ground Output power window main switch Battery voltage
(P) DOWN signal L
is operated DOWN.
6 Door key cylinder switch LH Key position
Ground Input 5→0
(R/W) UNLOCK signal (Neutral → Unlocked)
When rear RH switch in M
7 Rear power window motor RH
Ground Output power window main switch Battery voltage
(Y) UP signal
is operated UP.
JMKIA0070GB
PWC-43
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
Terminal No.
Description
(Wire color) Voltage [V]
Condition
Input/ (Approx.)
+ – Signal name
Output
IGN SW ON Battery voltage
Within 45 second after ig-
nition switch is turned to Battery voltage
10
Ground RAP signal Input OFF.
(W/R)
When front LH or RH door
is opened during retained 0
power operation.
When front LH switch in
11 Front door power window mo-
8 Output power window main switch Battery voltage
(GR) tor LH DOWN signal
is operated DOWN.
JMKIA0070GB
JPMIA0013GB
PWC-44
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
Wiring Diagram INFOID:0000000001702402
PWC
P
ALKWA0123GB
PWC-45
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
ALKIA0877GB
PWC-46
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
PWC
ALKIA0878GB
PWC-47
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
ALKIA0879GB
PWC-48
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
PWC
ALKIA0880GB
PWC-49
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
ALKIA0881GB
PWC-50
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
PWC
ALKIA0882GB
PWC-51
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
ALKIA0883GB
FAIL-SAFE CONTROL
Switches to fail-safe control when malfunction is detected in encoder signal that detects up/down speed and
direction of door glass. Switches to fail-safe control when error beyond regulation value is detected between
the fully closed position and the actual position of the glass.
PWC-52
POWER WINDOW MAIN SWITCH
< ECU DIAGNOSIS >
It changes to condition before initialization and the following functions do not operate when switched to fail-
safe control.
• Auto-up operation F
• Anti-pinch function
• Retained power function
G
Perform initial operation to recover when switched to fail-safe mode. However, it switches back to fail-safe
control when malfunction is found in power window switch or in motor.
H
PWC
PWC-53
FRONT POWER WINDOW SWITCH
< ECU DIAGNOSIS >
FRONT POWER WINDOW SWITCH
Reference Value INFOID:0000000001702404
TERMINAL LAYOUT
LIIA2454E
PHYSICAL VALUES
Terminal No.
Description
(Wire color) Voltage [V]
Condition
Input/ (Approx.)
+ – Signal name
Output
3
Ground Encoder ground — — 0
(BR)
4 When ignition switch ON or
Ground Encoder power supply Output 10
(W/R) power window timer operates
8 Power window motor When power window motor is
9 Output Battery voltage
(L) UP signal UP at operated.
9 Power window motor When power window motor is
8 Output Battery voltage
(G) DOWN signal DOWN at operated.
10
Ground Battery power supply Input — Battery voltage
(Y)
11
Ground Ground — — 0
(B)
JMKIA0070GB
PWC-54
FRONT POWER WINDOW SWITCH
< ECU DIAGNOSIS >
Terminal No.
Description
(Wire color) Voltage [V] A
Condition
Input/ (Approx.)
+ – Signal name
Output
B
JMKIA0070GB D
E
16 Input/ IGN SW ON or power window
Ground Power window serial link
(V) Output timer operating.
F
JPMIA0013GB
G
Wiring Diagram INFOID:0000000001702405
FAIL-SAFE CONTROL I
Switches to fail-safe control when malfunction is detected in encoder signal that detects up/down speed and
direction of door glass. Switches to fail-safe control when error beyond regulation value is detected between
the fully closed position and the actual position of the glass. J
O
It changes to condition before initialization and the following functions do not operate when switched to fail-
safe control.
• Auto-up operation
• Anti-pinch function P
• Retained power function
Perform initial operation to recover when switched to fail-safe mode. However, it switches back to fail-safe
control when malfunction is found in power window switch or in motor.
PWC-55
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY SWITCH
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
NONE OF THE POWER WINDOWS CAN BE OPERATED USING ANY
SWITCH
Diagnosis Procedure INFOID:0000000001702407
PWC-56
DRIVER SIDE POWER WINDOW ALONE DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
DRIVER SIDE POWER WINDOW ALONE DOES NOT OPERATE
A
Diagnosis Procedure INFOID:0000000001702408
PWC
PWC-57
FRONT PASSENGER SIDE POWER WINDOW ALONE DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
FRONT PASSENGER SIDE POWER WINDOW ALONE DOES NOT OPER-
ATE
Diagnosis Procedure INFOID:0000000001702409
PWC-58
REAR LH SIDE POWER WINDOW ALONE DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
REAR LH SIDE POWER WINDOW ALONE DOES NOT OPERATE
A
Diagnosis Procedure INFOID:0000000001702410
PWC
PWC-59
REAR RH SIDE POWER WINDOW ALONE DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
REAR RH SIDE POWER WINDOW ALONE DOES NOT OPERATE
Diagnosis Procedure INFOID:0000000001702411
PWC-60
ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (DRIVER SIDE)
< SYMPTOM DIAGNOSIS >
ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (DRIVER SIDE)
A
Diagnosis Procedure INFOID:0000000001702412
PWC
PWC-61
ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (PASSENGER SIDE)
< SYMPTOM DIAGNOSIS >
ANTI-PINCH SYSTEM DOES NOT OPERATE NORMALLY (PASSENGER
SIDE)
Diagnosis Procedure INFOID:0000000001702413
PWC-62
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NORMAL-
LY (DRIVER SIDE)
< SYMPTOM DIAGNOSIS >
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NOR-
A
MALLY (DRIVER SIDE)
Diagnosis Procedure INFOID:0000000001702414
B
1. CHECK ENCODER
Check encoder.
C
Refer to PWC-26, "DRIVER SIDE : Component Function Check".
Is the inspection result normal?
YES >> Inspection End. D
NO >> Check intermittent incident. Refer to GI-51, "Intermittent Incident".
PWC
PWC-63
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NORMAL-
LY (PASSENGER SIDE)
< SYMPTOM DIAGNOSIS >
AUTO OPERATION DOES NOT OPERATE BUT MANUAL OPERATE NOR-
MALLY (PASSENGER SIDE)
Diagnosis Procedure INFOID:0000000001702415
1. CHECK ENCODER
Check encoder.
Refer to PWC-28, "PASSENGER SIDE : Component Function Check".
Is the inspection result normal?
YES >> Inspection End.
NO >> Check intermittent incident. Refer to GI-51, "Intermittent Incident".
PWC-64
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPERATE
PROPERLY
< SYMPTOM DIAGNOSIS >
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPER-
A
ATE PROPERLY
Diagnosis Procedure INFOID:0000000001702416
B
1. CHECK FRONT DOOR SWITCH
Check front door switch.
C
Refer to PWC-32, "Component Function Check".
Is the inspection result normal?
YES >> Inspection End. D
NO >> Check intermittent incident. Refer to GI-51, "Intermittent Incident".
PWC
PWC-65
DOES NOT OPERATE BY KEY CYLINDER SWITCH
< SYMPTOM DIAGNOSIS >
DOES NOT OPERATE BY KEY CYLINDER SWITCH
Diagnosis Procedure INFOID:0000000001702417
PWC-66
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
A
Diagnosis Procedure INFOID:0000000001702418
PWC
PWC-67
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
< SYMPTOM DIAGNOSIS >
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
Diagnosis Procedure INFOID:0000000001702419
PWC-68
PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000001710925
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
H
PWC
PWC-69
POWER WINDOW MAIN SWITCH
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR
POWER WINDOW MAIN SWITCH
Removal and Installation INFOID:0000000001710928
REMOVAL
1. Remove the power window main switch finisher (2) from the
front door finisher LH. Refer to INT-10, "Removal and Installa-
tion".
2. Remove the three screws (A) from the power window main
switch (1), then separate from the finisher (2).
ALKIA1097ZZ
INSTALLATION
Installation is in the reverse order of removal.
PWC-70
FRONT POWER WINDOW SWITCH
< ON-VEHICLE REPAIR >
FRONT POWER WINDOW SWITCH
A
Removal and Installation INFOID:0000000001710929
REMOVAL B
1. Remove the front power window switch finisher (2) from the front
door finisher RH. Refer to INT-10, "Removal and Installation".
2. Release the four tabs (A), two on each side, then separate the C
front power window switch (1) from the finisher (2).
ALKIA1098ZZ
I
INSTALLATION
Installation is in the reverse order of removal.
J
PWC
PWC-71
REAR POWER WINDOW SWITCH
< ON-VEHICLE REPAIR >
REAR POWER WINDOW SWITCH
Removal and Installation - Rear Door Switch INFOID:0000000001710930
REMOVAL
1. Remove the rear power window switch finisher (2) from the rear
door finisher. Refer to INT-10, "Removal and Installation".
2. Release the two tabs (A), one on either side, then separate the
rear power window switch (1) from the finisher (2).
ALKIA1099ZZ
INSTALLATION
Installation is in the reverse order of removal.
PWC-72