Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

LT PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 152

K ELECTRICAL

B
SECTION
LIGHTING SYSTEM C

E
CONTENTS
PRECAUTIONS .......................................................... 4 FRONT SIDE MARKER LAMP ........................... 27 F
Precautions for Supplemental Restraint System Removal and Installation ........................................ 27
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN- FRONT COMBINATION LAMP ........................... 27
SIONER” .................................................................. 4 Disassembly and Assembly .................................... 28 G
General precautions for service operations ............. 4 FRONT COMBINATION LAMP ........................... 28
HEADLAMP (FOR USA) ............................................ 5 HEADLAMP (FOR CANADA) - DAYTIME LIGHT
Component Parts and Harness Connector Location..... 5 SYSTEM - .................................................................. 29
H
System Description .................................................. 5 Component Parts and Harness Connector Location... 29
OUTLINE ............................................................... 5 System Description ................................................. 29
BATTERY SAVER CONTROL .............................. 6 OUTLINE ............................................................. 30
AUTO LIGHT OPERATION ................................... 6 DAYTIME LIGHT OPERATION ........................... 31 I
VEHICLE SECURITY SYSTEM (PANIC ALARM)..... 6 COMBINATION SWITCH READING FUNCTION... 31
CAN Communication System Description ................ 6 AUTO LIGHT OPERATION ................................. 31
Schematic ................................................................ 7 CAN Communication System Description .............. 31 J
Wiring Diagram — H/LAMP — ................................. 8 Schematic ............................................................... 32
Terminals and Reference Values for BCM ............. 12 Wiring Diagram — DTRL — ................................... 33
Terminals and Reference Values for IPDM E/R ..... 12 Terminals and Reference Values for BCM .............. 37 LT
How to Proceed With Trouble Diagnosis ................ 12 Terminals and Reference Values for IPDM E/R ...... 37
Preliminary Check .................................................. 12 How to Proceed With Trouble Diagnosis ................ 37
CONSULT-II Function (BCM) ................................. 12 Preliminary Check .................................................. 37
CONSULT-II OPERATION .................................. 12 CHECK BCM CONFIGURATION ........................ 37 L
WORK SUPPORT ............................................... 13 INSPECTION FOR POWER SUPPLY AND
DATA MONITOR ................................................. 13 GROUND CIRCUIT ............................................. 37
ACTIVE TEST ..................................................... 14 INSPECTION PARKING BRAKE SWITCH CIR- M
SELF-DIAGNOSTIC RESULTS .......................... 15 CUIT .................................................................... 37
CONSULT-II Function (IPDM E/R) ......................... 15 CONSULT-II Functions ........................................... 38
CONSULT-II OPERATION .................................. 15 Daytime Light Control Does Not Operate Properly
DATA MONITOR ................................................. 16 (Normal Headlamps Operate Properly) .................. 38
ACTIVE TEST ..................................................... 17 Aiming Adjustment .................................................. 39
Headlamp HI Does Not Illuminate (Both Sides) ..... 17 Bulb Replacement .................................................. 39
Headlamp HI Does Not Illuminate (One Side) ....... 19 Removal and Installation ........................................ 39
High Beam Indicator Lamp Does Not Illuminate ... 20 Disassembly and Assembly .................................... 39
Headlamp LO Does Not Illuminate (Both Sides) ... 21 AUTO LIGHT SYSTEM ............................................. 40
Headlamp LO Does Not Illuminate (One Side) ...... 23 Component Parts and Harness Connector Location... 40
Headlamps Do Not Turn OFF ................................ 24 System Description ................................................. 41
Aiming Adjustment ................................................. 25 OUTLINE ............................................................. 41
LOW BEAM AND HIGH BEAM ........................... 26 COMBINATION SWITCH READING FUNCTION... 41
Bulb Replacement .................................................. 27 EXTERIOR LAMP BATTERY SAVER CONTROL... 41
HEADLAMP BULB .............................................. 27 DELAY TIMER FUNCTION ................................. 41
FRONT TURN SIGNAL/PARKING LAMP ........... 27 CAN Communication System Description .............. 41

Revision: September 2005 LT-1 2006 Pathfinder


Major Components and Functions .......................... 42 Preliminary Check ...................................................69
Schematic ............................................................... 43 CHECK POWER SUPPLY AND GROUND CIR-
Wiring Diagram — AUTO/L — ................................ 44 CUIT .....................................................................69
Terminals and Reference Values for BCM .............. 47 CONSULT-II Function (BCM) ..................................69
Terminals and Reference Values for IPDM E/R ...... 47 CONSULT-II OPERATION ...................................69
How to Proceed With Trouble Diagnosis ................ 47 DATA MONITOR ..................................................70
Preliminary Check .................................................. 47 ACTIVE TEST ......................................................71
SETTING CHANGE FUNCTIONS ....................... 47 Turn Signal Lamp Does Not Operate ......................71
CHECK BCM CONFIGURATION ........................ 47 Rear Turn Signal Lamp Does Not Operate .............72
CHECK POWER SUPPLY AND GROUND CIR- Hazard Warning Lamp Does Not Operate But Turn
CUIT .................................................................... 47 Signal Lamps Operate ............................................73
CONSULT-II Function (BCM) .................................. 47 Turn Signal Indicator Lamp Does Not Operate .......75
CONSULT-II OPERATION ................................... 47 Bulb Replacement ...................................................76
WORK SUPPORT ............................................... 48 FRONT TURN SIGNAL LAMP .............................76
DATA MONITOR .................................................. 49 REAR TURN SIGNAL LAMP ...............................76
ACTIVE TEST ..................................................... 50 Removal and Installation .........................................76
CONSULT-II Function (IPDM E/R) .......................... 51 FRONT TURN SIGNAL LAMP .............................76
CONSULT-II OPERATION ................................... 51 REAR TURN SIGNAL LAMP ...............................76
DATA MONITOR .................................................. 52 LIGHTING AND TURN SIGNAL SWITCH ................77
ACTIVE TEST ..................................................... 52 Removal and Installation .........................................77
Trouble Diagnosis Chart by Symptom .................... 53 REMOVAL ............................................................77
Lighting Switch Inspection ...................................... 53 INSTALLATION ....................................................77
Optical Sensor System Inspection .......................... 54 HAZARD SWITCH .....................................................78
Removal and Installation ........................................ 55 Removal and Installation .........................................78
OPTICAL SENSOR ............................................. 55 REMOVAL ............................................................78
FRONT FOG LAMP .................................................. 56 INSTALLATION ....................................................78
Component Parts and Harness Connector Location... 56 COMBINATION SWITCH ..........................................79
System Description ................................................. 56 Wiring Diagram — COMBSW — ............................79
OUTLINE ............................................................. 56 Combination Switch Reading Function ...................80
COMBINATION SWITCH READING FUNCTION... 57 CONSULT-II Function (BCM) ..................................80
EXTERIOR LAMP BATTERY SAVER CONTROL... 57 CONSULT-II OPERATION ...................................80
CAN Communication System Description .............. 57 DATA MONITOR ..................................................81
Wiring Diagram — F/FOG — .................................. 58 Combination Switch Inspection ...............................82
Terminals and Reference Values for BCM .............. 60 Removal and Installation .........................................84
Terminals and Reference Values for IPDM E/R ...... 60 Switch Circuit Inspection .........................................84
How to Proceed With Trouble Diagnosis ................ 60 STOP LAMP ..............................................................85
Preliminary Check .................................................. 60 System Description .................................................85
CHECK POWER SUPPLY AND GROUND CIR- Wiring Diagram — STOP/L — ................................86
CUIT .................................................................... 60 High-Mounted Stop Lamp .......................................87
CONSULT-II Functions ........................................... 60 BULB REPLACEMENT ........................................87
Front Fog Lamps Do Not Illuminate (Both Sides) ... 60 REMOVAL AND INSTALLATION .........................87
Front Fog Lamp Does Not Illuminate (One Side) ... 61 Stop Lamp ...............................................................87
Aiming Adjustment .................................................. 62 BULB REPLACEMENT ........................................87
Bulb Replacement .................................................. 63 REMOVAL AND INSTALLATION .........................87
Removal and Installation ........................................ 63 BACK-UP LAMP .......................................................88
FRONT FOG LAMP ............................................. 63 Wiring Diagram — BACK/L — ................................88
TURN SIGNAL AND HAZARD WARNING LAMPS... 64 Bulb Replacement ...................................................89
Component Parts and Harness Connector Location... 64 Removal and Installation .........................................89
System Description ................................................. 64 PARKING, LICENSE PLATE AND TAIL LAMPS ......90
OUTLINE ............................................................. 64 Component Parts and Harness Connector Location...90
TURN SIGNAL OPERATION ............................... 64 System Description .................................................90
HAZARD LAMP OPERATION ............................. 65 OPERATION BY LIGHTING SWITCH .................90
REMOTE KEYLESS ENTRY SYSTEM OPERA- COMBINATION SWITCH READING FUNCTION...91
TION .................................................................... 65 EXTERIOR LAMP BATTERY SAVER CONTROL...91
COMBINATION SWITCH READING FUNCTION... 66 CAN Communication System Description ..............91
CAN Communication System Description .............. 66 Schematic ...............................................................92
Wiring Diagram — TURN — ................................... 67 Wiring Diagram — TAIL/L — ...................................93
Terminals and Reference Values for BCM .............. 69 Terminals and Reference Values for BCM ..............97
How to Proceed With Trouble Diagnosis ................ 69 Terminals and Reference Values for IPDM E/R ......97

Revision: September 2005 LT-2 2006 Pathfinder


How to Proceed With Trouble Diagnosis ................ 97 ROOM LAMP TIMER OPERATION .................. 118
Preliminary Check .................................................. 97 INTERIOR LAMP BATTERY SAVER CONTROL. 118 A
CHECK POWER SUPPLY AND GROUND CIR- Schematic ............................................................. 119
CUIT .................................................................... 97 Wiring Diagram — INT/L — .................................. 121
CONSULT-II Functions ........................................... 97 Terminals and Reference Values for BCM ............ 126 B
Parking, Side Marker, License Plate and/or Tail How to Proceed With Trouble Diagnosis .............. 126
Lamps Do Not Illuminate ........................................ 97 Preliminary Check ................................................ 126
Parking, Side Marker, License Plate and Tail Lamps INSPECTION FOR POWER SUPPLY AND
Do Not Turn OFF (After Approx. 10 Minutes) ....... 104 GROUND CIRCUIT ........................................... 126 C
Bulb Replacement ................................................ 104 CONSULT-II Function (BCM) ............................... 126
FRONT PARKING LAMP .................................. 104 CONSULT-II OPERATION ................................. 126
TAIL LAMP ........................................................ 104 WORK SUPPORT ............................................. 127 D
LICENSE PLATE LAMP .................................... 104 DATA MONITOR ............................................... 128
Removal and Installation ...................................... 104 ACTIVE TEST ................................................... 128
LICENSE PLATE LAMP .................................... 104 Room/Map Lamp Control Does Not Operate ....... 129 E
REAR COMBINATION LAMP ................................ 105 Personal Lamp Control Does Not Operate (Room/
Bulb Replacement ................................................ 105 Map Lamps Operate) ............................................ 131
REMOVAL ......................................................... 105 All Interior Room Lamps Do Not Operate ............. 132
INSTALLATION ................................................. 105 Ignition Keyhole Illumination Control Does Not F
Removal and Installation ...................................... 105 Operate ................................................................. 132
REMOVAL ......................................................... 105 ILLUMINATION ....................................................... 135
INSTALLATION ................................................. 105 Component Parts and Harness Connector Location. 135 G
TRAILER TOW ....................................................... 106 System Description ............................................... 135
Component Parts and Harness Connector Location. 106 ILLUMINATION OPERATION BY LIGHTING
System Description .............................................. 106 SWITCH ............................................................ 136 H
TRAILER TAIL LAMP OPERATION .................. 107 EXTERIOR LAMP BATTERY SAVER CONTROL. 137
TRAILER STOP, TURN SIGNAL AND HAZARD CAN Communication System Description ............ 137
LAMP OPERATION .......................................... 107 Schematic ............................................................. 138
I
TRAILER POWER SUPPLY OPERATION ........ 107 Wiring Diagram — ILL — ...................................... 141
Schematic ............................................................ 109 Removal and Installation ...................................... 150
Wiring Diagram — T/TOW — ................................110 ILLUMINATION CONTROL SWITCH ................ 150
INTERIOR ROOM LAMP .........................................115 BULB SPECIFICATIONS ........................................ 151 J
Component Parts and Harness Connector Location..115 Headlamp ............................................................. 151
System Description ...............................................116 Exterior Lamp ....................................................... 151
POWER SUPPLY AND GROUND .....................116 Interior Lamp/Illumination ..................................... 151 LT
SWITCH OPERATION .......................................117

Revision: September 2005 LT-3 2006 Pathfinder


PRECAUTIONS

PRECAUTIONS PFP:00011

Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER” EKS00FTW

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
● To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
● Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
● Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
General precautions for service operations EKS00FTX

● Never work with wet hands.


● Turn the lighting switch OFF before disconnecting and connecting the connector.
● When checking the headlamp on/off operation, check it on vehicle and with the power connected to the
vehicle-side connector.
● Do not touch the headlamp bulb glass surface with bare hands or allow oil or grease to get on it. Do not
touch the headlamp bulb just after the headlamp is turned off, because it is very hot.
● When the bulb has burned out, wrap it in a thick vinyl bag and discard. Do not break the bulb.
● Leaving the bulb removed from the headlamp housing for a long period of time can deteriorate the perfor-
mance of the lens and reflector (dirt, clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
● Do not use organic solvent (paint thinner or gasoline) to clean lamps and to remove old sealant.

Revision: September 2005 LT-4 2006 Pathfinder


HEADLAMP (FOR USA)

HEADLAMP (FOR USA) PFP:26010


A
Component Parts and Harness Connector Location EKS00FTZ

F
WKIA4957E

1. IPDM E/R 2. BCM 3. Combination Switch (lighting switch)


E118, E119, E120, E121, M18, M19, M20 M28
G
E122, E123, E124 (view with instrument lower panel LH removed
4. Combination meter
M24 H

System Description EKS00FU0

Control of the front headlamp system operation is dependent upon the position of the combination switch I
(lighting switch). When the lighting switch is placed in the 2ND position, the BCM (body control module)
receives input requesting the headlamps (and tail lamps) illuminate. This input is communicated to the IPDM
E/R (intelligent power distribution module engine room) across the CAN communication lines. The CPU (cen-
tral processing unit) of the IPDM E/R controls the front headlamp high and front headlamp low relay coils. J
When energized, these relays direct power to the respective headlamps, which then illuminate.
OUTLINE LT
Power is supplied at all times
● to ignition relay, located in the IPDM E/R, and
● to headlamp high relay, located in the IPDM E/R, and L
● to headlamp low relay, located in the IPDM E/R, and
● through 20A fuse (No. 53, located in the IPDM E/R)
● to CPU of the IPDM E/R, and M
● through 50A fusible link (letter g , located in the fuse and fusible link box)
● to BCM terminal 70.
With the ignition switch in the ON or START position, power is supplied
● to ignition relay, located in the IPDM E/R, and
● through 10A fuse [No. 1, located in the fuse block (J/B)]
● to BCM terminal 38.
Ground is supplied
● to BCM terminal 67
● through grounds M57, M61 and M79, and
● to IPDM E/R terminals 38 and 59
● through grounds E9, E15 and E24.

Revision: September 2005 LT-5 2006 Pathfinder


HEADLAMP (FOR USA)

Low Beam Operation


With the lighting switch in 2ND position, the BCM receives input requesting the headlamps to illuminate. This
input is communicated to the IPDM E/R across the CAN communication lines. The CPU of the IPDM E/R con-
trols the headlamp low relay coil. When energized, this relay directs power
● through 15A fuse (No. 41, located in the IPDM E/R)
● through IPDM E/R terminal 54
● to front headlamp RH terminal 3, and
● through 15A fuse (No. 40, located in the IPDM E/R)
● through IPDM E/R terminal 52
● to front headlamp LH terminal 3.
Ground is supplied
● to front headlamp LH and RH terminal 2
● through grounds E9, E15 and E24.
With power and ground supplied, low beam headlamps illuminate.
High Beam Operation/Flash-to-Pass Operation
With the lighting switch in 2ND position and placed in HIGH or PASS position, the BCM receives input request-
ing the headlamp high beams to illuminate. This input is communicated to the IPDM E/R across the CAN com-
munication lines. The CPU of the combination meter controls the ON/OFF status of the HIGH BEAM indicator.
The CPU of the IPDM E/R controls the headlamp high relay coil. When energized, this relay directs power
● through 10A fuse (No. 34, located in the IPDM E/R)
● through IPDM E/R terminal 56
● to front headlamp RH terminal 1, and
● through 10A fuse (No. 35, located in the IPDM E/R)
● through IPDM E/R terminal 55
● to front headlamp LH terminal 1.
Ground is supplied
● to front headlamp LH and RH terminal 2
● through grounds E9, E15 and E24.
With power and ground supplied, the high beam headlamps illuminate.
BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 2ND position (ON), and the ignition switch is turned
from ON or ACC to OFF, the battery saver control feature is activated.
Under this condition, the headlamps remain illuminated for 5 minutes, unless the combination switch (lighting
switch) position is changed. If the combination switch (lighting switch) position is changed, then the headlamps
are turned off.
AUTO LIGHT OPERATION
Refer to LT-41, "System Description" for auto light operation.
VEHICLE SECURITY SYSTEM (PANIC ALARM)
The vehicle security system (panic alarm) will flash the high beams if the system is triggered. Refer to BL-44,
"Panic Alarm Operation" .
CAN Communication System Description EKS00FU1

Refer to LAN-25, "CAN COMMUNICATION" .

Revision: September 2005 LT-6 2006 Pathfinder


HEADLAMP (FOR USA)

Schematic EKS00FU2

LT

WKWA4303E

Revision: September 2005 LT-7 2006 Pathfinder


HEADLAMP (FOR USA)

Wiring Diagram — H/LAMP — EKS00FU3

WKWA4221E

Revision: September 2005 LT-8 2006 Pathfinder


HEADLAMP (FOR USA)

LT

WKWA2018E

Revision: September 2005 LT-9 2006 Pathfinder


HEADLAMP (FOR USA)

WKWA2019E

Revision: September 2005 LT-10 2006 Pathfinder


HEADLAMP (FOR USA)

LT

WKWA4222E

Revision: September 2005 LT-11 2006 Pathfinder


HEADLAMP (FOR USA)

Terminals and Reference Values for BCM EKS00FU4

Refer to BCS-12, "Terminals and Reference Values for BCM" .


Terminals and Reference Values for IPDM E/R EKS00FU5

Refer to PG-28, "Terminals and Reference Values for IPDM E/R"


How to Proceed With Trouble Diagnosis EKS00FU6

1. Confirm the symptom or customer complaint.


2. Understand operation description and function description. Refer to LT-5, "System Description" .
3. Perform the Preliminary Check. Refer to LT-12, "Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does the headlamp operate normally? If YES: GO TO 6. If NO: GO TO 4.
6. Inspection End.
Preliminary Check EKS00FU7

Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" and PG-30, "IPDM E/R Power/Ground Cir-
cuit Inspection" .
CONSULT-II Function (BCM) EKS00FU8

CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
BCM diagnostic
Diagnostic mode Description
test item
Supports inspections and adjustments. Commands are transmitted to the BCM
WORK SUPPORT for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
Inspection by part
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.

CONSULT-II OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, then turn igni-
tion switch ON.

BBIA0538E

Revision: September 2005 LT-12 2006 Pathfinder


HEADLAMP (FOR USA)

2. Touch "START (NISSAN BASED VHCL)".


A

BCIA0029E

D
3. Touch "BCM" on "SELECT SYSTEM" screen.
If "BCM" is not indicated, go to GI-40, "CONSULT-II Data Link
Connector (DLC) Circuit" .
E

G
BCIA0030E

4. Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.


H

LKIA0183E
LT

WORK SUPPORT
Operation Procedure L
1. Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
2. Touch "WORK SUPPORT" on "SELECT DIAG MODE" screen.
3. Touch item on "SELECT WORK ITEM" screen. M
4. Touch "START".
5. Touch "CHANGE SETT".
6. The setting will be changed and "CUSTOMIZING COMPLETED" will be displayed.
7. Touch "END".
Display Item List
Item Description CONSULT-II Factory setting
Exterior lamp battery saver control mode can be changed ON ×
BATTERY SAVER SET in this mode. Selects exterior lamp battery saver control
mode between ON/OFF. OFF —

DATA MONITOR
Operation Procedure
1. Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
2. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
3. Touch either "ALL SIGNALS" or "SELECTION FROM MENU" on the "SELECT MONITOR ITEM" screen.
Revision: September 2005 LT-13 2006 Pathfinder
HEADLAMP (FOR USA)

ALL SIGNALS Monitors all the signals.


SELECTION FROM MENU Selects and monitors individual signal.

4. Touch "START".
5. When "SELECTION FROM MENU" is selected, touch individual items to be monitored. When "ALL SIG-
NALS" is selected, all the items will be monitored.
6. Touch "RECORD" while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch "STOP".
Display Item List
Monitor item Contents
Displays "IGN position (ON)/OFF, ACC position (OFF)" judged from the ignition switch sig-
IGN ON SW "ON/OFF"
nal.
ACC ON SW "ON/OFF" Displays "ACC (ON)/OFF, Ignition OFF (OFF)" status judged from ignition switch signal.
Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from
HI BEAM SW "ON/OFF"
lighting switch signal.
Displays status (headlamp switch 1: ON/Others: OFF) of headlamp switch 2 judged from
HEAD LAMP SW 1 "ON/OFF"
lighting switch signal.
Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from
HEAD LAMP SW 2 "ON/OFF"
lighting switch signal.
Displays status (lighting switch 1st position: ON/Others: OFF) of lighting switch judged
LIGHT SW 1ST "ON/OFF"
from lighting switch signal.
Displays status of the lighting switch as judged from the lighting switch signal. (AUTO posi-
AUTO LIGHT SW "ON/OFF"
tion: ON/Other than AUTO position: OFF)
Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from
PASSING SW "ON/OFF"
lighting switch signal.
Displays status (front fog lamp switch: ON/Others: OFF) of front fog lamp switch judged
FR FOG SW "ON/OFF"
from lighting switch signal.
Displays status of the front door LH as judged from the front door switch LH signal. (Door is
DOOR SW-DR "ON/OFF"
open: ON/Door is closed: OFF)
Displays status of the front door RH as judged from the front door switch RH signal. (Door
DOOR SW-AS "ON/OFF"
is open: ON/Door is closed: OFF)
Displays status of the rear door as judged from the rear door switch (RH) signal. (Door is
DOOR SW-RR "ON/OFF"
open: ON/Door is closed: OFF)
Displays status of the rear door as judged from the rear door switch (LH) signal. (Door is
DOOR SW-RL "ON/OFF"
open: ON/Door is closed: OFF)
Displays status of the back door as judged from the back door switch signal. (Door is open:
BACK DOOR SW "ON/OFF"
ON/Door is closed: OFF)
TURN SIGNAL R "ON/OFF" Displays status (Turn right: ON/Others: OFF) as judged from lighting switch signal.
TURN SIGNAL L "ON/OFF" Displays status (Turn left: ON/Others: OFF) as judged from lighting switch signal.
CARGO LAMP SW "ON/OFF" Displays status of cargo lamp switch.
Displays "ambient light (close to 5V when dark/close to 0V when light)" judged from optical
OPTICAL SENSOR [0 - 5V]
sensor signal.

ACTIVE TEST
Operation Procedure
1. Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
2. Touch "ACTIVE TEST" on "SELECT DIAG MODE" screen.
3. Touch item to be tested and check operation of the selected item.
4. During the operation check, touching "BACK" deactivates the operation.

Revision: September 2005 LT-14 2006 Pathfinder


HEADLAMP (FOR USA)

Display Item List


Test item Description
A

TAIL LAMP Allows tail lamp relay to operate by switching ON-OFF.


HEAD LAMP Allows headlamp relay (HI, LO) to operate by switching ON-OFF. B
FR FOG LAMP Allows fog lamp relay to operate by switching ON-OFF.
CORNERING LAMP Not used.
CARGO LAMP Allows cargo lamp to operate by switching ON-OFF. C

SELF-DIAGNOSTIC RESULTS
Operation Procedure D
1. Touch "BCM" on "SELECT TEST ITEM" screen.
2. Touch "SELF-DIAG RESULTS" on "SELECT DIAG MODE" screen.
3. Self-diagnostic results are displayed. E
Display Item List
Monitored item CONSULT-ll display Description
F
CAN communication CAN communication [U1000] Malfunction is detected in CAN communication.
CAN communication system 1 to 6
CAN communication system Malfunction is detected in CAN system.
[U1000] G
CONSULT-II Function (IPDM E/R) EKS00FU9

CONSULT-II can display each diagnostic item using the diagnostic test modes shown following. H
IPDM E/R diagnostic mode Description
SELF-DIAG RESULTS Displays IPDM E/R self-diagnosis results.
DATA MONITOR Displays IPDM E/R input/output data in real time. I
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
J
CONSULT-II OPERATION
CAUTION:
LT
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, then turn the L
ignition switch ON.

BBIA0538E

Revision: September 2005 LT-15 2006 Pathfinder


HEADLAMP (FOR USA)

2. Touch "START (NISSAN BASED VHCL)".

BCIA0029E

3. Touch "IPDM E/R" on "SELECT SYSTEM" screen.


If "IPDM E/R" is not displayed, refer to GI-40, "CONSULT-II Data
Link Connector (DLC) Circuit" .

BCIA0030E

4. Select the desired part to be diagnosed on the "SELECT DIAG


MODE" screen.

BCIA0031E

DATA MONITOR
Operation Procedure
1. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
2. Touch "ALL SIGNALS", "MAIN SIGNALS" or "SELECTION FROM MENU" on the "SELECT MONITOR
ITEM" screen.

ALL SIGNALS All items will be monitored.


MAIN SIGNALS Monitor the predetermined item.
SELECTION FROM MENU Select any item for monitoring.

3. Touch "START".
4. Touch the required monitoring item on "SELECTION FROM MENU". In "ALL SIGNALS", all items are
monitored. In "MAIN SIGNALS", predetermined items are monitored.
5. Touch "RECORD" while monitoring to record the status of the item being monitored. To stop recording,
touch "STOP".

Revision: September 2005 LT-16 2006 Pathfinder


HEADLAMP (FOR USA)

All Items, Main Items, Select Item Menu


Monitor item selection
A
CONSULT-II Display or
Item name ALL MAIN SELECTION Description
screen display unit
SIGNALS SIGNALS FROM MENU
B
Parking, license plate
TAIL&CLR REQ ON/OFF × × × Signal status input from BCM
and tail lamps request
Headlamp low beam
HL LO REQ ON/OFF × × × Signal status input from BCM C
request
Headlamp high beam
HL HI REQ ON/OFF × × × Signal status input from BCM
request
Daytime lights request DTRL REQ ON/OFF × – × Signal status input from BCM
D

Front fog lamps request FR FOG REQ ON/OFF × × × Signal status input from BCM

NOTE: E
Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is at ACC, the dis-
play may not be correct.
ACTIVE TEST F
Operation Procedure
1. Touch "ACTIVE TEST" on "SELECT DIAG MODE" screen.
G
2. Touch "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
3. Touch item to be tested, and check operation.
4. Touch "START". H
5. Touch "STOP" while testing to stop the operation.
Test item CONSULT-II screen display Description
Allows tail lamp relay to operate by switching operation ON-OFF at
I
Tail lamp relay output TAIL LAMP
your option.
Allows headlamp relay (HI, LO) to operate by switching operation
Headlamp relay (HI, LO) out- J
(OFF, HI, LO) at your option (Headlamp high beam repeats ON-OFF
put
LAMPS every 1 second).
Front fog lamp relay (FOG) Allows fog lamp relay (FOG) to operate by switching operation ON-
output OFF at your option. LT
Headlamp HI Does Not Illuminate (Both Sides) EKS00FUA

1. CHECK COMBINATION SWITCH INPUT SIGNAL L


Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor,
make sure "HI BEAM SW" turns ON-OFF linked with operation of
lighting switch. M
When lighting switch is in : HI BEAM SW ON
HIGH position
OK or NG
OK >> GO TO 2.
NG >> Check lighting switch. Refer to LT-82, "Combination
Switch Inspection" .
SKIA4193E

Revision: September 2005 LT-17 2006 Pathfinder


HEADLAMP (FOR USA)

2. HEADLAMP ACTIVE TEST


1. Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST"
on "SELECT DIAG MODE" screen.
2. Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
3. Touch "HI" on "ACTIVE TEST" screen.
4. Make sure headlamp high beam operates.
Headlamp high beam should operate.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4. WKIA1438E

3. CHECK IPDM E/R


1. Select "IPDM E/R" on CONSULT-II, and select "DATA MONI-
TOR" on "SELECT DIAG MODE" screen.
2. Make sure "HL LO REQ" and "HL HI REQ" turns ON when light-
ing switch is in HIGH position.
When lighting switch is in : HL LO REQ ON
HIGH position : HL HI REQ ON
OK or NG
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and
Installation of IPDM E/R" .
NG >> Replace BCM. Refer to BCS-27, "Removal and Installa- SKIA5775E

tion" .

4. CHECK HEADLAMP INPUT SIGNAL


1. Turn ignition switch OFF.
2. Disconnect front headlamp RH and LH connectors.
3. Turn ignition switch ON.
4. Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST"
on "SELECT DIAG MODE" screen.
5. Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
6. Touch "HI" on "ACTIVE TEST" screen.
7. When headlamp high beam is operating, check voltage between
front headlamp RH and LH harness connector and ground.
WKIA4989E

Front headlamp
(+) (–) Voltage
Connector Terminal
RH E107
1 Ground Battery voltage
LH E11
OK or NG
OK >> GO TO 6.
NG >> GO TO 5.

Revision: September 2005 LT-18 2006 Pathfinder


HEADLAMP (FOR USA)

5. CHECK HEADLAMP CIRCUIT A


1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector E123 B
terminal 56 and front headlamp RH harness connector E107 ter-
minal 1.
C
56 - 1 : Continuity should exist.
4. Check continuity between IPDM E/R harness connector E123
terminal 55 and front headlamp LH harness connector E11 ter- D
minal 1.
WKIA3498E

55 - 1 : Continuity should exist.


OK or NG E
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and Installation of IPDM E/R" .
NG >> Repair harness or connector.
F
6. CHECK HEADLAMP GROUND
1. Turn ignition switch OFF. G
2. Check continuity between front headlamp RH harness connec-
tor E107 terminal 2 and ground.
2 - Ground : Continuity should exist. H
3. Check continuity between front headlamp LH harness connector
E11 terminal 2 and ground.
I
2 - Ground : Continuity should exist.
OK or NG
OK >> Check front headlamp connector for damage or poor J
connection. Repair as necessary. WKIA3499E

NG >> Repair harness or connector.


LT
Headlamp HI Does Not Illuminate (One Side) EKS00FUB

1. BULB INSPECTION
Inspect inoperative headlamp bulb. L
OK or NG
OK >> GO TO 2.
NG >> Replace headlamp bulb. Refer to LT-27, "HEADLAMP BULB" . M

Revision: September 2005 LT-19 2006 Pathfinder


HEADLAMP (FOR USA)

2. CHECK POWER TO HEADLAMP


1. Disconnect inoperative headlamp connector.
2. Turn the high beam headlamps ON.
3. Check voltage between inoperative headlamp terminal and
ground.
Front headlamp
Voltage
(+) (–)
(Approx.)
Connector Terminal
RH E107
1 Ground Battery voltage
LH E11
OK or NG
WKIA3497E
OK >> GO TO 3.
NG >> GO TO 4.

3. CHECK HEADLAMP GROUND


1. Turn the high beam headlamps OFF.
2. Check continuity between inoperative headlamp connector and
ground.
Front headlamp
Continuity
Connector Terminal
RH E107
2 Ground Yes
LH E11
OK or NG
OK >> Check front headlamp connector for damage or poor
connection. Repair as necessary. WKIA3499E

NG >> Repair open circuit in harness between inoperative


headlamp and ground.

4. INSPECTION BETWEEN IPDM E/R AND HEADLAMPS


1. Disconnect IPDM E/R connector and inoperative headlamp connector.
2. Check continuity between harness connector terminals of IPDM
E/R and harness connector terminals of inoperative headlamp.
IPDM E/R Front headlamp
Continuity
Connector Terminal Connector Terminal
56 RH E107
E123 1 Yes
55 LH E11

OK or NG
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and
Installation of IPDM E/R" . WKIA3498E

NG >> Check for short and open circuits in harness between


IPDM E/R and front headlamps. Repair as necessary.
High Beam Indicator Lamp Does Not Illuminate EKS00FUC

1. BULB INSPECTION
Inspect CAN communication system. Refer to LAN-25, "CAN COMMUNICATION" .
OK or NG
OK >> Replace combination meter. Refer to IP-14, "COMBINATION METER" .
NG >> Repair as necessary.

Revision: September 2005 LT-20 2006 Pathfinder


HEADLAMP (FOR USA)

Headlamp LO Does Not Illuminate (Both Sides) EKS00FUD

1. CHECK COMBINATION SWITCH INPUT SIGNAL A

Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor,


make sure "HEAD LAMP SW 1" and "HEAD LAMP SW 2" turns ON- B
OFF linked with operation of lighting switch.
When lighting switch is in : HEAD LAMP SW 1 ON
2ND position : HEAD LAMP SW 2 ON C
OK or NG
OK >> GO TO 2.
NG >> Check lighting switch. Refer to LT-82, "Combination D
Switch Inspection" .
WKIA4262E

E
2. HEADLAMP ACTIVE TEST
1. Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST"
on "SELECT DIAG MODE" screen. F
2. Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
3. Touch "LO" on "ACTIVE TEST" screen.
G
4. Make sure headlamp low beam operates.
Headlamp low beam should operate.
H
OK or NG
OK >> GO TO 3.
NG >> GO TO 4. WKIA1438E
I
3. CHECK IPDM E/R
1. Select "IPDM E/R" on CONSULT-II, and select "DATA MONI- J
TOR" on "SELECT DIAG MODE" screen.
2. Make sure "HL LO REQ" turns ON when lighting switch is in
2ND position. LT
When lighting switch is in : HL LO REQ ON
2ND position
L
OK or NG
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and
Installation of IPDM E/R" .
NG >> Replace BCM. Refer to BCS-27, "Removal and Installa- SKIA5780E M
tion" .

Revision: September 2005 LT-21 2006 Pathfinder


HEADLAMP (FOR USA)

4. CHECK HEADLAMP INPUT SIGNAL


1. Turn ignition switch OFF.
2. Disconnect front headlamp RH and LH connectors.
3. Turn ignition switch ON.
4. Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST" on "SELECT DIAG MODE" screen.
5. Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
6. Touch "LO" on "ACTIVE TEST" screen.
7. When headlamp low beam is operating, check voltage between
front headlamp RH and LH harness connector and ground.
Front headlamp
(+) (–) Voltage
Connector Terminal
RH E107
3 Ground Battery voltage
LH E11
OK or NG
WKIA3500E
OK >> GO TO 6.
NG >> GO TO 5.

5. CHECK HEADLAMP CIRCUIT


1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector E123
terminal 54 and front headlamp RH harness connector E107 ter-
minal 3.
54 - 3 : Continuity should exist.
4. Check continuity between IPDM E/R harness connector E123
terminal 52 and front headlamp LH harness connector E11 ter-
minal 3.
WKIA3501E

52 - 3 : Continuity should exist.


OK or NG
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and Installation of IPDM E/R" .
NG >> Repair harness or connector.

6. CHECK HEADLAMP GROUND


1. Turn ignition switch OFF.
2. Check continuity between front headlamp RH harness connec-
tor E107 terminal 2 and ground.
2 - Ground : Continuity should exist.
3. Check continuity between front headlamp LH harness connector
E11 terminal 2 and ground.
2 - Ground : Continuity should exist.
OK or NG
OK >> Check front headlamp connector for damage or poor
connection. Repair as necessary. WKIA3499E

NG >> Repair harness or connector.

Revision: September 2005 LT-22 2006 Pathfinder


HEADLAMP (FOR USA)

Headlamp LO Does Not Illuminate (One Side) EKS00FUE

1. BULB INSPECTION A

Inspect inoperative headlamp bulb.


OK or NG B
OK >> GO TO 2.
NG >> Replace headlamp bulb. Refer to LT-27, "HEADLAMP BULB" .
C
2. CHECK POWER TO HEADLAMP
1. Disconnect inoperative headlamp connector.
D
2. Turn the low beam headlamps ON.
3. Check voltage between inoperative headlamp connector termi-
nal and ground.
E
Front headlamp
Voltage
(+) (–)
(Approx.)
F
Connector Terminal
RH E107
3 Ground Battery voltage
LH E11 G
OK or NG
WKIA4990E
OK >> GO TO 3.
NG >> GO TO 4. H

3. CHECK HEADLAMP GROUND


1. Turn the low beam headlamps OFF. I
2. Check continuity between inoperative headlamp connector ter-
minal and ground.
J
Front headlamp
Continuity
Connector Terminal
RH E107 LT
2 Ground Yes
LH E11
OK or NG L
OK >> Check front headlamp and IPDM E/R connector. Repair
as necessary. WKIA3499E

NG >> Repair open circuit in harness between inoperative


headlamp and ground. M

4. INSPECTION BETWEEN IPDM E/R AND HEADLAMPS


1. Disconnect IPDM E/R connector.
2. Check continuity between harness connector terminals of IPDM
E/R harness connector terminals of inoperative headlamp.
IPDM E/R Front headlamp
Continuity
Connector Terminal Connector Terminal
54 RH E107
E123 3 Yes
52 LH E11
OK or NG
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and
Installation of IPDM E/R" . WKIA3501E

NG >> Check for short and open circuits in harness between


IPDM E/R and headlamps. Repair as necessary.

Revision: September 2005 LT-23 2006 Pathfinder


HEADLAMP (FOR USA)

Headlamps Do Not Turn OFF EKS00FUF

1. CHECK COMBINATION SWITCH INPUT SIGNAL


Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor,
make sure "HEAD LAMP SW 1" and "HEAD LAMP SW 2" turns ON-
OFF linked with operation of lighting switch.
When lighting switch is in : HEAD LAMP SW 1 OFF
OFF position : HEAD LAMP SW 2 OFF
OK or NG
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and
Installation of IPDM E/R" .
NG >> GO TO 2.
SKIA5200E

2. CHECK LIGHTING SWITCH


Check lighting switch. Refer to LT-82, "Combination Switch Inspection" .
OK or NG
OK >> GO TO 3.
NG >> Replace lighting switch. Refer to LT-84, "Removal and Installation" .

3. CHECKING CAN COMMUNICATIONS BETWEEN BCM AND IPDM E/R


Select "BCM" on CONSULT-II and perform self-diagnosis for BCM.
Display of self-diagnosis results
NO DTC>> Replace IPDM E/R. Refer to PG-32, "Removal and
Installation of IPDM E/R" .
CAN COMM CIRCUIT>> Refer to BCS-20, "CAN Communication
Inspection Using CONSULT-II (Self-Diagnosis)" .

SKIA1039E

Revision: September 2005 LT-24 2006 Pathfinder


HEADLAMP (FOR USA)

Aiming Adjustment EKS00FUG

LKIA0568E

G
For details, refer to the regulations in your area.
NOTE:
If vehicle front body has been repaired and /or the headlamp assembly has been replaced, check headlamp H
aiming.
● Before performing aiming adjustment, check the following:
– Confirm headlamp aiming switch is set to "0" (zero) position. I
– Ensure all tires are inflated to correct pressure.
– Place vehicle and screen on level surface.
– Ensure there is no load in vehicle other than the driver (or equivalent weight placed in driver's position). J
Coolant and engine oil filled to correct level, and fuel tank full.
– Confirm spare tire, jack and tools are properly stowed.
LT
– Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
– Use adjusting screw to perform aiming adjustment
L

Revision: September 2005 LT-25 2006 Pathfinder


HEADLAMP (FOR USA)

LOW BEAM AND HIGH BEAM

WKIA4885E

1 Adjustment screen 2 Headlamp bulb center (HV point) A Minimum acceptable vertical aim
dimension (see aiming chart)
B Maximum acceptable vertical aim C H-V point D Distance of headlamp aiming
dimension (see aiming chart) screen from vehicle 7.62 m (25 ft.)
E Maximum aim evaluation distance F Minimum aim evaluation distance G Aim evaluation area
from vertical center on aiming from vertical center on aiming
screen 399mm (3° R). screen 133 mm (1°R)
H Horizontal aiming evaluation line. Þ Right

Aiming Chart
A (Minimum acceptable vertical aim dimension) -3.3 mm (0.13 in) 0.025° up
B (Maximum acceptable vertical aim dimension) 36.6 mm (1.44 in) 0.275° down
NOTE:
● By regulation, no means for horizontal aim adjustment is provided from the factory; only vertical aim is
adjustable.
● Basic illuminating area for evaluation and/or adjustment should be within range shown on aiming chart.
1. Use adjustment screw to perform aiming adjustment.
● Cover the opposite lamp and ensure fog lamps, if equipped, are turned off.

CAUTION:
Do not tighten adjustment screw beyond specified torque or damage may occur.
Adjustment torque 1.67 N.m (17 kg-cm, 14.8 in-lb)

2. Adjust beam pattern until cut-off line (top edge of illumination area) is positioned at the specified height off
ground. Measure cut-off line within distance J on H-line. See aiming chart.

Revision: September 2005 LT-26 2006 Pathfinder


HEADLAMP (FOR USA)

Bulb Replacement EKS00FUH

HEADLAMP BULB A
Removal
NOTE:
Reach through engine room for bulb replacement access. B
CAUTION:
Grasp only the plastic base when handling the bulb. Never touch the glass envelope.
1. Turn front headlamp switch OFF. C
2. Disconnect the electrical connector.
3. Rotate the headlamp bulb retaining ring counterclockwise and remove.
D
4. Pull the headlamp bulb straight out from the headlamp assembly.
NOTE:
Remove the headlamp bulb from the headlamp assembly just before a replacement bulb is installed. Dust,
E
moisture, foreign materials, etc. entering headlamp body may affect performance.
Installation
Installation is in the reverse order of removal. F
FRONT TURN SIGNAL/PARKING LAMP
Removal
G
NOTE:
Reach through engine room for bulb replacement access.
1. Turn the bulb socket counterclockwise to unlock it.
H
2. Pull the bulb to remove it from the socket.
Installation
Installation is in the reverse order of removal. I
CAUTION:
After installing the bulb, be sure to install the bulb socket securely for watertightness.
FRONT SIDE MARKER LAMP J
Removal
NOTE:
LT
Reach through engine room for bulb replacement access.
1. Turn the bulb socket counterclockwise to unlock it.
2. Pull the bulb to remove it from the socket.
L
Installation
Installation is in the reverse order of removal.
CAUTION: M
After installing the bulb, be sure to install the bulb socket securely for watertightness.
Removal and Installation EKS00FUI

FRONT COMBINATION LAMP


Removal
1. Remove front portion of front fender protector. Refer to EI-20, "FENDER PROTECTOR" .
2. Remove the front bumper. Refer to EI-14, "Removal and Installation" .

Revision: September 2005 LT-27 2006 Pathfinder


HEADLAMP (FOR USA)

3. Remove the front combination lamp bolts.

LKIA0569E

4. Disconnect the front combination lamp connector and remove front combination lamp.
Installation
Installation is in the reverse order of removal.

: 6.0 N·m (0.61 kg-m, 53 in-lb)

Disassembly and Assembly EKS00FUJ

FRONT COMBINATION LAMP

LKIA0570E

1. Headlamp assembly 2. Headlamp bulb 3. Headlamp bulb retaining ring


4. Wiring harness assembly 5. Front side marker lamp bulb 6. Front turn signal/parking lamp bulb

Revision: September 2005 LT-28 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM - PFP:26010


A
Component Parts and Harness Connector Location EKS00FUK

LT

WKIA4958E
M
1. IPDM E/R 2. Parking brake switch 3. BCM
E118, E119, E120, E121, E122, E53 M18, M19, M20
E123, E124 (view with instrument lower panel LH removed)
4. ECM 5. Generator 6. Daytime light relay 1
E16 E205
(view with ECM cover removed)
7. Daytime Light Relay 2 8. Combination switch (lighting switch) 9. Combination meter
M28 M24

System Description EKS00FUL

Daytime light system turns on daytime light lamps while driving. Daytime light lamps are not turned on if
engine is activated with parking brake on. Take off parking brake to turn on daytime light lamps. The lamps
turn off when lighting switch is in the 2ND position or AUTO position (Headlamp is "ON") and when lighting
switch is in the PASSING position. (Daytime light lamps are not turned off only by parking brake itself.)
A parking brake signal and engine run or stop signal are sent to BCM (body control module) by CAN commu-
nication line.

Revision: September 2005 LT-29 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

OUTLINE
Power is supplied at all times
● to ignition relay, located in the IPDM E/R, and
● through 10A fuse [No. 19, located in the fuse block (J/B)]
● to combination meter terminal 3, and
● through 20A fuse (No. 53, located in the IPDM E/R)
● to CPU (central processing unit) of IPDM E/R (intelligent power distribution module engine room), and
● to headlamp high relay, located in the IPDM E/R, and
● to headlamp low relay, located in the IPDM E/R, and
● through 50A fusible link (letter g , located in the fuse and fusible link box)
● to BCM terminal 70, and
● through 10A fuse (No. 45, located in the IPDM E/R)
● to daytime light relay 1 terminals 2 and 5.
When the ignition switch is in ON or START position, power is supplied
● to ignition relay, located in the IPDM E/R, and
● through 10A fuse [No. 14, located in the fuse block (J/B)]
● to combination meter terminal 16, and
● through 10A fuse [No. 1, located in the fuse block (J/B)]
● to BCM terminal 38.
Ground is supplied
● to BCM terminal 67 and
● to combination meter terminals 13 and 23
● through grounds M57, M61 and M79.
Low Beam Operation
With the lighting switch in 2ND position, the BCM receives input requesting the headlamps to illuminate. This
input is communicated to the IPDM E/R across the CAN communication lines. The CPU of the IPDM E/R con-
trols the headlamp low relay coil. When energized, this relay directs power
● through 15A fuse (No. 41, located in the IPDM E/R)
● through IPDM E/R terminal 54
● to front headlamp RH terminal 3, and
● through 15A fuse (No. 40, located in the IPDM E/R)
● through IPDM E/R terminal 52
● to daytime light relay 2 terminals 2 and 5, and
● through daytime light relay 2 terminal 3
● to front headlamp LH terminal 3.
Ground is supplied
● to front headlamp RH terminal 2
● to daytime light relay 1 terminal 4
● to daytime light relay 2 terminal 1
● through grounds E9, E15 and E24.
When the CPU of the IPDM E/R energizes the headlamp low relay, it de-energizes daytime relay 1. When de-
energized, this relay supplies ground
● to front headlamp LH terminal 2
● through daytime light relay 1 terminal 3.
With power and ground supplied, low beam headlamps illuminate.
High Beam Operation/Flash-to-Pass Operation
With the lighting switch in 2ND position and placed in HIGH or PASS position, the BCM receives input request-
ing the headlamp high beams to illuminate. This input is communicated to the IPDM E/R across the CAN com-

Revision: September 2005 LT-30 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

munication lines. The CPU of the combination meter controls the ON/OFF status of the HIGH BEAM indicator.
The CPU of the IPDM E/R controls the headlamp high relay coil. When energized, this relay directs power A
● through 10A fuse (No. 34, located in the IPDM E/R)
● through IPDM E/R terminal 56
● to front headlamp RH terminal 1, and B
● through 10A fuse (No. 35, located in the IPDM E/R)
● through IPDM E/R terminal 55
C
● to front headlamp LH terminal 1.
Ground is supplied
● to front headlamp RH terminal 2, and D
● to daytime light relay 1 terminal 4, and
● to daytime light relay 2 terminal 1
● through grounds E9, E15 and E24. E
When the CPU of the IPDM E/R energizes the headlamp high relay, it de-energizes daytime relay 1. When de-
energized, this relay supplies ground
● to front headlamp LH terminal 2 F
● through daytime light relay 1 terminal 3.
With power and ground supplied, the high beam headlamps illuminate.
G
DAYTIME LIGHT OPERATION
With the engine running, the lighting switch in the OFF or 1ST position and parking brake released, the IPDM
E/R receives input requesting the daytime lights illuminate. This input is communicated across the CAN com-
H
munication lines. The CPU of the IPDM E/R controls daytime light relay 1 coil. When energized, this relay
directs power
● through daytime light relay 1 terminal 3
I
● through front headlamp LH terminal 2
● through front headlamp LH terminal 1
● through IPDM E/R terminal 55 J
● through 10A fuse (No. 35, located in the IPDM E/R)
● through 10A fuse (No. 34, located in the IPDM E/R)
● through IPDM E/R terminal 56 LT
● to front headlamp RH terminal 1.
Ground is supplied
● to combination lamp RH terminal 2 L
● through grounds E9, E15 and E24.
With power and ground supplied, the daytime lights illuminate. The high beam headlamps are now wired in
series and illuminate at a reduced intensity. M

COMBINATION SWITCH READING FUNCTION


Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
AUTO LIGHT OPERATION
For auto light operation, refer to LT-41, "System Description" in AUTO LIGHT SYSTEM.
CAN Communication System Description EKS00FUM

Refer to LAN-25, "CAN COMMUNICATION" .

Revision: September 2005 LT-31 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

Schematic EKS00FUN

WKWA4304E

Revision: September 2005 LT-32 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

Wiring Diagram — DTRL — EKS00FUO

LT

WKWA4223E

Revision: September 2005 LT-33 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

WKWA4224E

Revision: September 2005 LT-34 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

LT

WKWA4225E

Revision: September 2005 LT-35 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

WKWA3081E

Revision: September 2005 LT-36 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

Terminals and Reference Values for BCM EKS00FUP

A
Refer to BCS-12, "Terminals and Reference Values for BCM" .
Terminals and Reference Values for IPDM E/R EKS00FUQ

Refer to PG-28, "Terminals and Reference Values for IPDM E/R" . B

How to Proceed With Trouble Diagnosis EKS00FUR

1. Confirm the symptom or customer complaint. C


2. Understand operation description and function description. Refer to LT-29, "System Description" .
3. Perform the Preliminary Check. Refer to LT-37, "Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction. D
5. Does the daytime light system operate normally? If YES: GO TO 6. If NO: GO TO 4.
6. Inspection End.
E
Preliminary Check EKS00FUS

CHECK BCM CONFIGURATION


1. CHECK BCM CONFIGURATION F

Confirm BCM configuration for "DTRL" is set to "WITH". Refer to BCS-21, "READ CONFIGURATION PROCE-
DURE" . G
OK or NG
OK >> Continue preliminary check. Refer to LT-37, "INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT" . H
NG >> Change BCM configuration for "DTRL" to "WITH". Refer to BCS-23, "WRITE CONFIGURATION
PROCEDURE" .
INSPECTION FOR POWER SUPPLY AND GROUND CIRCUIT I
Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" and PG-30, "IPDM E/R Power/Ground Cir-
cuit Inspection" .
INSPECTION PARKING BRAKE SWITCH CIRCUIT J

1. CHECK BRAKE INDICATOR


LT
1. Turn ignition switch ON.
2. Apply parking brake.
3. Release parking brake. L
Brake indicator in combination meter should illuminate
when parking brake is applied and turn OFF when
released. M
OK or NG
OK >> Inspection End.
NG >> GO TO 2.

2. CHECK PARKING BRAKE SWITCH SIGNAL


1. Turn ignition switch OFF.
2. Disconnect parking brake switch connector.
3. Turn ignition switch ON.
4. Check voltage between parking brake switch harness connector
E53 terminal 1 and ground.
1 - Ground : Battery voltage should exist.
OK or NG
OK >> Replace parking brake switch.
NG >> GO TO 3. WKIA3303E

Revision: September 2005 LT-37 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

3. CHECK PARKING BRAKE SWITCH CIRCUIT


1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector
M24 terminal 31 and parking brake switch harness connector
E53 terminal 1.
1 - 31 : Continuity should exist.
OK or NG
OK >> Replace combination meter. Refer to IP-14, "COMBINA-
TION METER" .
WKIA3304E
NG >> Repair harness or connector.
CONSULT-II Functions EKS00FUT

Refer to LT-12, "CONSULT-II Function (BCM)" in HEADLAMP (FOR USA).


Refer to LT-15, "CONSULT-II Function (IPDM E/R)" in HEADLAMP (FOR USA).
Daytime Light Control Does Not Operate Properly (Normal Headlamps Operate
Properly) EKS00FUU

1. CHECK DAYTIME LIGHT RELAY 1 POWER SUPPLY CIRCUIT


1. Remove daytime light relay 1.
2. Check voltage between daytime light relay 1 harness connector
E103 terminals 2, 5 and ground.
2, 5 - Ground : Battery voltage should exist.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.

WKIA3305E

2. CHECK DAYTIME LIGHT RELAY 1


1. Apply battery voltage to daytime light relay 1 terminal 2 and ground terminal 1.
2. Check continuity between terminals 3 and 5.
3-5 : Continuity should exist.
OK or NG
OK >> GO TO 3.
NG >> Replace daytime light relay 1.

WIIA0291E

Revision: September 2005 LT-38 2006 Pathfinder


HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -

3. CHECK INPUT SIGNAL A


1. Connect daytime light relay 1.
2. Start engine and release parking brake. Headlamp switch OFF.
3. Select "IPDM E/R" on CONSULT-II. With data monitor, make B
sure "DTRL REQ" turns ON-OFF linked with operation of park-
ing brake switch.
C
Parking brake ON : DTRL REQ ON
Parking brake OFF : DTRL REQ OFF
OK or NG D
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and WKIA1449E

Installation of IPDM E/R" .


NG >> GO TO 4. E

4. CHECKING CAN COMMUNICATIONS


Select "BCM" on CONSULT-II and perform self-diagnosis for BCM. F
Displayed self-diagnosis results
NO DTC>>Replace BCM. Refer to BCS-27, "Removal and Installa-
tion" . G
CAN COMM CIRCUIT>> Check BCM CAN communication system.
Refer to BCS-20, "CAN Communication Inspection
Using CONSULT-II (Self-Diagnosis)" . H

SKIA1039E
I

Aiming Adjustment EKS00FUV

Refer to LT-25, "Aiming Adjustment" . J


Bulb Replacement EKS00FUW

Refer to LT-28, "Disassembly and Assembly" . LT


Removal and Installation EKS00FUX

Refer to LT-27, "Removal and Installation" . L


Disassembly and Assembly EKS00FUY

Refer to LT-28, "Disassembly and Assembly" .


M

Revision: September 2005 LT-39 2006 Pathfinder


AUTO LIGHT SYSTEM

AUTO LIGHT SYSTEM PFP:28491

Component Parts and Harness Connector Location EKS00FUZ

WKIA4959E

1. IPDM E/R 2. BCM 3. Combination switch (lighting switch)


E118, E119, E120, E121, M18, M19, M20 M28
E122, E123, E124 (view with instrument lower panel LH removed)
4. Combination meter 5. Rear door switch LH 6. Optical sensor
M24 B18 M145
Rear door switch RH
B116
7. Back door switch 7. Front door switch LH
D502 B8
Front door switch RH
B108

Revision: September 2005 LT-40 2006 Pathfinder


AUTO LIGHT SYSTEM

System Description EKS00FV0

A
Automatically turns on/off the parking lamps and the headlamps in accordance with ambient light.
Timing for when the lamps turn on/off can be selected using four modes.
OUTLINE B
The auto light control system uses an optical sensor that detects outside brightness.
When the lighting switch is in "AUTO" position, it automatically turns on/off the parking lamps and the head-
lamps in accordance with the ambient light. Sensitivity can be adjusted in four steps. For the details of the set-
C
ting, refer to LT-47, "SETTING CHANGE FUNCTIONS" .
Optical sensor ground is supplied
● to optical sensor terminal 3
D
● through BCM (body control module) terminal 18.
When ignition switch is turned to "ON" position and when outside brightness is darker than prescribed level,
input is supplied
E
● to BCM terminal 58
● from optical sensor terminal 4.
The headlamps will then illuminate. For a description of headlamp operation, refer to LT-5, "System Descrip- F
tion" .
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" . G
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the AUTO position, and the ignition switch is turned from H
ON or ACC to OFF, and one of the front doors is opened, the battery saver control feature is activated.
Under this condition, the headlamps remain illuminated for 5 minutes, then the headlamps are turned off.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
I
DELAY TIMER FUNCTION
When the ignition switch is ON and auto light switch is ON, the BCM turns on/off the headlamps. In delay timer
function, ignition is OFF, auto light sensor power source is OFF and the headlamps are not turned on/off by the
J
BCM. On condition that:
● when the state of ignition switch ON or ACC is ON and output judgment by auto light function is headlamp
ON changes to ignition switch and ACC are OFF and any door switch is ON, output judgment by BCM
should be headlamp ON for 5 minutes by timer. After time out, output judgment by BCM should be head- LT
lamp OFF.
● when the state of any door switch is turned to ON from OFF while 45 second or 5 minute timer is counting,
timer stops, and restarts counting for 5 minutes, then BCM judges output as headlamp ON. After time out, L
BCM judges output as headlamp OFF.
● when the state of front door switch LH, front door switch RH, rear door switch LH, rear door switch RH or
back door latch (door ajar switch) is ON turns to all door switches are OFF while 45 second or 5 minute M
timer is counting, timer stops, and restarts counting for 45 seconds, then BCM judges output as headlamp
ON. After timer out, BCM judges output as headlamp OFF.
● when the state is ignition switch ON or ACC is ON or auto light switch OFF while timer is counting, timer
stops counting and BCM turns on/off lamps according to headlamp function, front fog lamp function, auto
light function and headlamp battery save function.
Delay timer control mode can be changed by the function setting of CONSULT-II or with the display (with
NAVI).
CAN Communication System Description EKS00FV1

Refer to LAN-25, "CAN COMMUNICATION" .

Revision: September 2005 LT-41 2006 Pathfinder


AUTO LIGHT SYSTEM

Major Components and Functions EKS00FV2

Components Functions
● Turns on/off circuits of tail light and headlamp according to signals from light sensor, lighting switch
BCM (AUTO), front door switch LH, front door switch RH, rear door switches, back door switch, and igni-
tion switch (ON, OFF).
Optical sensor ● Converts ambient light (lux) to voltage, and sends it to BCM. (Detects lightness of 50 to 1,300 lux)

Revision: September 2005 LT-42 2006 Pathfinder


AUTO LIGHT SYSTEM

Schematic EKS00FV3

LT

WKWA4305E

Revision: September 2005 LT-43 2006 Pathfinder


AUTO LIGHT SYSTEM

Wiring Diagram — AUTO/L — EKS00FV4

WKWA4226E

Revision: September 2005 LT-44 2006 Pathfinder


AUTO LIGHT SYSTEM

LT

WKWA2028E

Revision: September 2005 LT-45 2006 Pathfinder


AUTO LIGHT SYSTEM

WKWA4306E

Revision: September 2005 LT-46 2006 Pathfinder


AUTO LIGHT SYSTEM

Terminals and Reference Values for BCM EKS00FV5

A
Refer to BCS-12, "Terminals and Reference Values for BCM" .
Terminals and Reference Values for IPDM E/R EKS00FV6

Refer to PG-28, "Terminals and Reference Values for IPDM E/R" . B

How to Proceed With Trouble Diagnosis EKS00FV7

1. Confirm the symptom or customer complaint. C


2. Understand operation description and function description. Refer to LT-41, "System Description" .
3. Carry out the Preliminary Check. Refer to LT-47, "Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction. Refer to LT-53, "Trouble Diagnosis Chart D
by Symptom" .
5. Does the auto light system operate normally? If YES: GO TO 6. If NO: GO TO 4.
6. Inspection End. E

Preliminary Check EKS00FV8

SETTING CHANGE FUNCTIONS F


● Sensitivity of auto light system can be adjusted using CONSULT-II or with display (with NAVI). Refer to LT-
48, "WORK SUPPORT" .
CHECK BCM CONFIGURATION G
1. CHECK BCM CONFIGURATION
Confirm BCM configuration for "AUTO LIGHT" is set to "WITH". Refer to BCS-21, "READ CONFIGURATION H
PROCEDURE" .
OK or NG
OK >> Continue preliminary check. Refer to LT-47, "CHECK POWER SUPPLY AND GROUND CIR- I
CUIT" .
NG >> Change BCM configuration for "AUTO LIGHT" to "WITH". Refer to BCS-23, "WRITE CONFIGU-
RATION PROCEDURE" . J
CHECK POWER SUPPLY AND GROUND CIRCUIT
Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" and PG-30, "IPDM E/R Power/Ground Cir-
cuit Inspection" . LT

CONSULT-II Function (BCM) EKS00FV9

CONSULT-II can display each diagnostic item using the diagnostic test modes shown following. L
BCM diagnostic
Diagnostic mode Description
test item
Supports inspections and adjustments. Commands are transmitted to the BCM M
WORK SUPPORT for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
Inspection by part
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.

CONSULT-II OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.

Revision: September 2005 LT-47 2006 Pathfinder


AUTO LIGHT SYSTEM

1. With the ignition switch OFF, connect CONSULT-II and CON-


SULT-II CONVERTER to the data link connector, then turn igni-
tion switch ON.

BBIA0538E

2. Touch "START (NISSAN BASED VHCL)".

BCIA0029E

3. Touch "BCM" on "SELECT SYSTEM" screen.


If "BCM" is not indicated, go to GI-40, "CONSULT-II Data Link
Connector (DLC) Circuit" .

BCIA0030E

4. Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.

LKIA0183E

WORK SUPPORT
Operation Procedure
1. Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
2. Touch "WORK SUPPORT" on "SELECT DIAG MODE" screen.
3. Touch "CUSTOM A/LIGHT SETTING" or "ILL DELAY SET" on "SELECT WORK ITEM" screen.
4. Touch "START".
5. Touch "MODE 1-4" of setting to be changed (CUSTOM A/LIGHT SETTING). Touch "MODE1-8" of setting
to be changed (ILL DELAY SET).
6. Touch "CHANGE SETT".

Revision: September 2005 LT-48 2006 Pathfinder


AUTO LIGHT SYSTEM

7. The setting will be changed and "CUSTOMIZING COMPLETED" will be displayed.


8. Touch "END". A

Work Support Setting Item


● Sensitivity of auto light can be selected and set from four modes. B
Work item Description
Auto light sensitivity can be changed in this mode. Sensitivity can be adjusted in four modes.
CUSTOM A/LIGHT SETTING C
● MODE 1 (Normal-default)/ MODE 2 (Desensitized)/MODE 3 (Sensitive)/MODE4 (Insensitive)
Auto light delay off timer period can be changed in this mode. Selects auto light delay off timer
period among eight modes.
ILL DELAY SET D
● MODE 1 (45 sec.)/MODE 2 (OFF)/MODE 3 (30 sec.)/MODE 4 (60 sec.)/MODE 5 (90 sec.)/
MODE 6 (120 sec.)/MODE 7 (150 sec.)/MODE 8 (180 sec.)

DATA MONITOR
E
Operation Procedure
1. Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
2. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen. F
3. Touch either "ALL SIGNALS" or "SELECTION FROM MENU" on the "SELECT MONITOR ITEM" screen.

ALL SIGNALS Monitors all the signals.


G
SELECTION FROM MENU Selects and monitors individual signal.

4. Touch "START".
5. When "SELECTION FROM MENU" is selected, touch individual items to be monitored. When "ALL SIG- H
NALS" is selected, all the items will be monitored.
6. Touch "RECORD" while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch "STOP". I
Display Item List
Monitor item Contents J
Displays "IGN position (ON)/OFF, ACC position (OFF)" judged from the ignition switch
IGN ON SW "ON/OFF"
signal.
ACC ON SW "ON/OFF" Displays "ACC (ON)/OFF, Ignition OFF (OFF)" status judged from ignition switch signal. LT
Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from
HI BEAM SW "ON/OFF"
lighting switch signal.

HEAD LAMP SW 1 "ON/OFF"


Displays status (headlamp switch 1: ON/Others: OFF) of headlamp switch 2 judged from L
lighting switch signal.
Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from
HEAD LAMP SW 2 "ON/OFF"
lighting switch signal. M
Displays status (lighting switch 1st position: ON/Others: OFF) of lighting switch judged
LIGHT SW 1ST "ON/OFF"
from lighting switch signal.
Displays status of the lighting switch as judged from the lighting switch signal. (AUTO
AUTO LIGHT SW "ON/OFF"
position: ON/Other than AUTO position: OFF)
Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged
PASSING SW "ON/OFF"
from lighting switch signal.
Displays status (front fog lamp switch: ON/Others: OFF) of front fog lamp switch judged
FR FOG SW "ON/OFF"
from lighting switch signal.
Displays status of the front door LH as judged from the front door switch LH signal. (Door
DOOR SW-DR "ON/OFF"
is open: ON/Door is closed: OFF)
Displays status of the front door RH as judged from the front door switch RH signal. (Door
DOOR SW-AS "ON/OFF"
is open: ON/Door is closed: OFF)
Displays status of the rear door as judged from the rear door switch (RH) signal. (Door is
DOOR SW-RR "ON/OFF"
open: ON/Door is closed: OFF)
Displays status of the rear door as judged from the rear door switch (LH) signal. (Door is
DOOR SW-RL "ON/OFF"
open: ON/Door is closed: OFF)

Revision: September 2005 LT-49 2006 Pathfinder


AUTO LIGHT SYSTEM

Monitor item Contents


Displays status of the back door as judged from the back door switch signal. (Door is
BACK DOOR SW "ON/OFF"
open: ON/Door is closed: OFF)
TURN SIGNAL R "ON/OFF" Displays status (Turn right: ON/Others: OFF) as judged from lighting switch signal.
TURN SIGNAL L "ON/OFF" Displays status (Turn left: ON/Others: OFF) as judged from lighting switch signal.
CARGO LAMP SW "ON/OFF" Displays status of cargo lamp.
Displays "ambient light (close to 5V when dark/close to 0V when light)" judged from opti-
OPTICAL SENSOR [0 - 5V]
cal sensor signal.

ACTIVE TEST
Operation Procedure
1. Touch "HEAD LAMP" on "SELECT TEST ITEM" screen.
2. Touch "ACTIVE TEST" on "SELECT DIAG MODE" screen.
3. Touch item to be tested and check operation of the selected item.
4. During the operation check, touching "BACK" deactivates the operation.
Display Item List
Test item Description
TAIL LAMP Allows tail lamp relay to operate by switching ON-OFF.
HEAD LAMP Allows headlamp relay (HI, LO) to operate by switching ON-OFF.
FR FOG LAMP Allows fog lamp relay to operate by switching ON-OFF.
CARGO LAMP Allows cargo lamp to operate by switching ON-OFF.

Revision: September 2005 LT-50 2006 Pathfinder


AUTO LIGHT SYSTEM

CONSULT-II Function (IPDM E/R) EKS00FVA

A
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
IPDM E/R diagnostic mode Description
SELF-DIAG RESULTS Displays IPDM E/R self-diagnosis results. B
DATA MONITOR Displays IPDM E/R input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
C
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.

CONSULT-II OPERATION
D
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON- E
SULT-II CONVERTER to the data link connector, then turn the
ignition switch ON.
F

H
BBIA0538E

2. Touch "START (NISSAN BASED VHCL)".


I

LT

BCIA0029E

L
3. Touch "IPDM E/R" on "SELECT SYSTEM" screen.
If "IPDM E/R" is not displayed, go to GI-40, "CONSULT-II Data
Link Connector (DLC) Circuit" .
M

BCIA0030E

Revision: September 2005 LT-51 2006 Pathfinder


AUTO LIGHT SYSTEM

4. Select the desired part to be diagnosed on the "SELECT DIAG


MODE" screen.

BCIA0031E

DATA MONITOR
Operation Procedure
1. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
2. Touch "ALL SIGNALS", "MAIN SIGNALS" or "SELECTION FROM MENU" on the "SELECT MONITOR
ITEM" screen.

ALL SIGNALS All items will be monitored.


MAIN SIGNALS Monitor the predetermined item.
SELECTION FROM MENU Select any item for monitoring.

3. Touch "START".
4. Touch the required monitoring item on "SELECTION FROM MENU". In "ALL SIGNALS", all items are
monitored. In "MAIN SIGNALS", predetermined items are monitored.
5. Touch "RECORD" while monitoring to record the status of the item being monitored. To stop recording,
touch "STOP".
All Items, Main Items, Select Item Menu
Monitor item selection
CONSULT-II Display or
Item name ALL MAIN SELECTION Description
screen display unit
SIGNALS SIGNALS FROM MENU
Parking, license plate
TAIL&CLR REQ ON/OFF × × × Signal status input from BCM
and tail lamps request
Headlamp low beam
HL LO REQ ON/OFF × × × Signal status input from BCM
request
Headlamp high beam
HL HI REQ ON/OFF × × × Signal status input from BCM
request
Front fog lamps request FR FOG REQ ON/OFF × × × Signal status input from BCM

NOTE:
Perform monitoring of IPDM E/R data with the ignition switch ON. When the ignition switch is at ACC, the dis-
play may not be correct.
ACTIVE TEST
Operation Procedure
1. Touch "ACTIVE TEST" on "SELECT DIAG MODE" screen.
2. Touch item to be tested, and check operation.
3. Touch "START".
4. Touch "STOP" while testing to stop the operation.

Revision: September 2005 LT-52 2006 Pathfinder


AUTO LIGHT SYSTEM

Test item CONSULT-II screen display Description


A
Allows tail lamp relay to operate by switching operation ON-OFF at
Tail lamp relay output TAIL LAMP
your option.
Allows headlamp relay (HI, LO) to operate by switching operation
Headlamp relay (HI, LO) out-
(OFF, HI, LO) at your option (Headlamp high beam repeats ON-OFF
B
put
LAMPS every 1 second).
Allows fog lamp relay to operate by switching operation ON-OFF at
Front fog lamp relay output
your option. C

Trouble Diagnosis Chart by Symptom EKS00FVB

Trouble phenomenon Malfunction system and reference D


● Parking lamps and headlamps will not illuminate when out-
side of the vehicle becomes dark. (Lighting switch 1st posi- ● Refer to LT-48, "WORK SUPPORT" .
tion and 2nd position operate normally.) E
● Refer to LT-53, "Lighting Switch Inspection" .
● Parking lamps and headlamp will not go out when outside of
the vehicle becomes light. (Lighting switch 1st position and ● Refer to LT-54, "Optical Sensor System Inspection" .
2nd position operate normally.) If above systems are normal, replace BCM. Refer to BCS-27,
"Removal and Installation" . F
● Headlamps go out when outside of the vehicle becomes
light, but parking lamps stay on.
● Refer to LT-48, "WORK SUPPORT" .
Parking lamps illuminate when outside of the vehicle becomes G
● Refer to LT-54, "Optical Sensor System Inspection" .
dark, but headlamps stay off. (Lighting switch 1st position and
2nd position operate normally.) If above systems are normal, replace BCM. Refer to BCS-27,
"Removal and Installation" .
H
● Refer to LT-54, "Optical Sensor System Inspection" .
Auto light adjustment system will not operate. (Lighting switch
AUTO, 1st position and 2nd position operate normally.) If above system is normal, replace BCM. Refer to BCS-27, "Removal
and Installation" .
I
● CAN communication line to BCM inspection. Refer to BCS-20,
Auto light adjustment system will not operate. "CAN Communication Inspection Using CONSULT-II (Self-Diagno-
sis)" .
● CAN communication line inspection between BCM and combina- J
tion meter. Refer to BCS-20, "CAN Communication Inspection
Using CONSULT-II (Self-Diagnosis)" .
Shut off delay feature will not operate.
● Refer to BL-29, "Door Switch Check" . LT
If above system is normal, replace BCM. Refer to BCS-27, "Removal
and Installation" .

Lighting Switch Inspection EKS00FVC


L
1. CHECK LIGHTING SWITCH INPUT SIGNAL
With CONSULT-II M
Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor,
make sure "AUTO LIGHT SW" turns ON-OFF linked with operation
of lighting switch.
When lighting switch is in : AUTO LIGHT SW ON
AUTO position
Without CONSULT-II
Refer to LT-82, "Combination Switch Inspection" .
OK or NG
OK >> Inspection End.
NG >> Check lighting switch. Refer to LT-82, "Combination SKIA4196E

Switch Inspection" .

Revision: September 2005 LT-53 2006 Pathfinder


AUTO LIGHT SYSTEM

Optical Sensor System Inspection EKS00FVD

1. CHECK OPTICAL SENSOR INPUT SIGNAL


With CONSULT-II
Select "BCM" on CONSULT-II. With "OPTICAL SENSOR" data mon-
itor, check difference in the voltage when the optical sensor is illumi-
nated and not illuminated.
Illuminated
OPTICAL SENSOR : 3.1V or more
Not illuminated
OPTICAL SENSOR : 0.6V or less
NOTE:
Optical sensor must be completely subjected to work lamp light. If
WKIA0486E
the optical sensor is insufficiently illuminated, the measured value
may not satisfy the standard.
Without CONSULT-II
GO TO 2.
OK or NG
OK >> Inspection End.
NG >> GO TO 2.

2. CHECK OPTICAL SENSOR SIGNAL GROUND CIRCUIT


1. Turn ignition switch OFF.
2. Disconnect BCM connector and optical sensor connector.
3. Check continuity (open circuit) between BCM harness connector
M18 terminal 18 and optical sensor harness connector M145
terminal 3.
18 - 3 : Continuity should exist.
4. Check continuity (short circuit) between BCM harness connector
M18 terminal 18 and ground.
18 - Ground : Continuity should not exist. WKIA3328E

OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.

3. CHECK OPTICAL SENSOR SIGNAL CIRCUIT


1. Check continuity (open circuit) between BCM harness connector
M20 terminal 58 and optical sensor harness connector M145
terminal 4.
58 - 4 : Continuity should exist.
2. Check continuity (short circuit) between BCM harness connector
M20 terminal 58 and ground.
58 - Ground : Continuity should not exist.
OK or NG
OK >> Replace optical sensor. Refer to LT-55, "Removal and WKIA3329E

Installation" . Recheck sensor output with CONSULT-II.


If NG, replace BCM. Refer to BCS-27, "Removal and Installation" .
NG >> Repair harness or connector.

Revision: September 2005 LT-54 2006 Pathfinder


AUTO LIGHT SYSTEM

Removal and Installation EKS00FVE

OPTICAL SENSOR A
Removal
1. Using a thin blade screwdriver, gently pry upward to release optical sensor from defrost grille.
2. Disconnect optical sensor connector. B

E
LKIA0571E

Installation
Installation is in the reverse order of removal. F

LT

Revision: September 2005 LT-55 2006 Pathfinder


FRONT FOG LAMP

FRONT FOG LAMP PFP:26150

Component Parts and Harness Connector Location EKS00FVF

WKIA4960E

1. IPDM E/R 2. BCM 3. Combination switch (lighting switch)


E118, E119, E120, E121, M18, M19, M20 M28
E122, E123, E124 (view with instrument lower panel RH removed)
4. Combination meter
M24

System Description EKS00FVG

Control of the fog lamps is dependent upon the position of the combination switch (lighting switch). The light-
ing switch must be in the 2ND position or AUTO position (LOW beam is ON) for front fog lamp operation.
When the lighting switch is placed in the fog lamp position, the BCM (body control module) receives input sig-
nal requesting the fog lamps to illuminate. When the headlamps are illuminated, this input signal is communi-
cated to the IPDM E/R (intelligent power distribution module engine room) across the CAN communication
lines. The CPU (central processing unit) of the IPDM E/R controls the front fog lamp relay coil. When acti-
vated, this relay directs power to the front fog lamps.
OUTLINE
Power is supplied at all times
● to ignition relay, located in the IPDM E/R, and
● to front fog lamp relay, located in the IPDM E/R, and
● through 20A fuse (No. 53, located in the IPDM E/R)
● to CPU of the IPDM E/R, and
● through 50A fusible link (letter g , located in the fuse and fusible link box)
● to BCM terminal 70.
When the ignition switch is in ON or START position, power is supplied
● to ignition relay, located in the IPDM E/R, and
● through 10A fuse [No. 1, located in the fuse block (J/B)]
● to BCM terminal 38.
Ground is supplied
● to BCM terminal 67
● through grounds M57, M61 and M79, and
● to IPDM E/R terminals 38 and 59
● through grounds E9, E15 and E24.
FOG LAMP OPERATION
The fog lamp switch is built into the combination switch. The lighting switch must be in the 2ND position or
AUTO position (LOW beam is ON) and the fog lamp switch must be ON for fog lamp operation.

Revision: September 2005 LT-56 2006 Pathfinder


FRONT FOG LAMP

With the fog lamp switch in the ON position, the CPU of the IPDM E/R grounds the coil side of the fog lamp
relay. The fog lamp relay then directs power A
● through 20A fuse (No. 56, located in the IPDM E/R)
● through IPDM E/R terminal 50
● to front fog lamp LH terminal 1, and B
● through IPDM E/R terminal 51
● to front fog lamp RH terminal 1.
C
Ground is supplied
● to front fog lamp LH and RH terminal 2
● through grounds E9, E15 and E24. D
With power and ground supplied, the front fog lamps illuminate.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" . E

EXTERIOR LAMP BATTERY SAVER CONTROL


When the combination switch (lighting switch) is in the 2ND position (ON), the fog lamp switch is ON, and the F
ignition switch is turned from ON or ACC to OFF, the battery saver control feature is activated.
Under this condition, the fog lamps (and headlamps) remain illuminated for 5 minutes, then the fog lamps (and
headlamps) are turned off.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II. G

CAN Communication System Description EKS00FVH

Refer to LAN-25, "CAN COMMUNICATION" . H

LT

Revision: September 2005 LT-57 2006 Pathfinder


FRONT FOG LAMP

Wiring Diagram — F/FOG — EKS00FVI

WKWA4227E

Revision: September 2005 LT-58 2006 Pathfinder


FRONT FOG LAMP

LT

WKWA3082E

Revision: September 2005 LT-59 2006 Pathfinder


FRONT FOG LAMP

Terminals and Reference Values for BCM EKS00FVJ

Refer to BCS-12, "Terminals and Reference Values for BCM" .


Terminals and Reference Values for IPDM E/R EKS00FVK

Refer to PG-28, "Terminals and Reference Values for IPDM E/R" .


How to Proceed With Trouble Diagnosis EKS00FVL

1. Confirm the symptom or customer complaint.


2. Understand operation description and function description. Refer to LT-56, "System Description" .
3. Perform the Preliminary Check. Refer to LT-60, "Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does the front fog lamp operate normally? If YES: GO TO 6. If NO: GO TO 4.
6. Inspection End.
Preliminary Check EKS00FVM

CHECK POWER SUPPLY AND GROUND CIRCUIT


Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" and PG-30, "IPDM E/R Power/Ground Cir-
cuit Inspection" .
CONSULT-II Functions EKS00FVN

Refer to LT-12, "CONSULT-II Function (BCM)" in HEADLAMP (FOR USA).


Refer to LT-15, "CONSULT-II Function (IPDM E/R)" in HEADLAMP (FOR USA).
Front Fog Lamps Do Not Illuminate (Both Sides) EKS00FVO

1. CHECK COMBINATION SWITCH INPUT SIGNAL


Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor,
make sure "FR FOG SW" turns ON-OFF linked with operation of
lighting switch.
When lighting switch is in : FR FOG SW ON
FOG position
OK or NG
OK >> GO TO 2.
NG >> Check lighting switch. Refer to LT-82, "Combination
Switch Inspection" .
SKIA5897E

2. FOG LAMP ACTIVE TEST


1. Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST"
on "SELECT DIAG MODE" screen.
2. Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
3. Touch "FOG" on "ACTIVE TEST" screen.
4. Make sure fog lamps operate.
Fog lamps should operate.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4. WKIA1438E

Revision: September 2005 LT-60 2006 Pathfinder


FRONT FOG LAMP

3. CHECK IPDM E/R A


1. Select "IPDM E/R" on CONSULT-II, and select "DATA MONI-
TOR" on "SELECT DIAG MODE" screen.
2. Make sure "FR FOG REQ" turns ON when lighting switch is in B
FOG position.
When lighting switch is in : FR FOG REQ ON
FOG position C

OK or NG
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and D
Installation of IPDM E/R" .
NG >> Replace BCM. Refer to BCS-27, "Removal and Installa- SKIA5898E

tion" .
E
4. IPDM E/R INSPECTION
1. Disconnect fog lamp LH and RH. F
2. Start auto active test. Refer to PG-24, "Auto Active Test" . When
front fog lamp relay is operating, check voltage between left/right
front fog lamp connector terminals and ground.
G
Front fog lamp
Voltage
(+) (–)
(Approx.) H
Connector Terminal
LH E101
1 Ground Battery voltage
RH E102 WKIA3306E
I
OK or NG
OK >> Check front fog lamp bulbs and replace as necessary. Refer to LT-63, "Bulb Replacement" .
NG >> Replace IPDM E/R. Refer to PG-32, "Removal and Installation of IPDM E/R" . J

Front Fog Lamp Does Not Illuminate (One Side) EKS00FVP

1. BULB INSPECTION LT

Inspect bulb of lamp which does not illuminate.


OK or NG L
OK >> GO TO 2.
NG >> Replace lamp bulb. Refer to LT-63, "Bulb Replacement" .

2. INSPECTION BETWEEN IPDM E/R AND FRONT FOG LAMPS M

1. Disconnect IPDM E/R connector and inoperative front fog lamp connector.
2. Check continuity between harness connector terminals of IPDM
E/R and harness connector terminal of front fog lamps.
IPDM E/R Front fog lamp
Continuity
Connector Terminal Connector Terminal
50 LH E101
E123 1 Yes
51 RH E102
OK or NG
OK >> Check ground circuit. If OK, replace IPDM E/R. Refer to
PG-32, "Removal and Installation of IPDM E/R" . If NG, WKIA3307E

repair harness or connector.


NG >> Check for short circuits and open circuits in harness between IPDM E/R and front fog lamps.

Revision: September 2005 LT-61 2006 Pathfinder


FRONT FOG LAMP

Aiming Adjustment EKS00FVQ

The fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. Before performing aiming
adjustment, make sure of the following.
● Keep all tires inflated to correct pressure.
● Place vehicle on level ground.
● See that vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and
tools). Have the driver or equivalent weight placed in driver seat.
Adjust aiming in the vertical direction by turning the adjustment
screw.
NOTE:
Use a Phillips screwdriver to adjust. Turn screw clockwise to raise
pattern and counterclockwise to lower pattern.

LKIA0572E

1. Set the distance between the screen and the center of the fog
lamp lens as shown.

MEL327G

2. Turn front fog lamps ON.


3. Remove front portion of fender protector(s) for adjustment screw access. Refer to EI-21, "Removal and
Installation of Front Fender Protector"
4. Adjust front fog lamps using adjustment screw so that the top
edge of the high intensity zone is 100 mm (4 in) below the height
of the fog lamp centers as shown.
● When performing adjustment, if necessary, cover the headlamps
and opposite fog lamp.

MEL328G

Revision: September 2005 LT-62 2006 Pathfinder


FRONT FOG LAMP

Bulb Replacement EKS00FVR

A
1. Remove front portion of fender protector. Refer to EI-21, "Removal and Installation of Front Fender Pro-
tector"
2. Disconnect fog lamp connector.
B
3. Turn the bulb counterclockwise to remove it.
CAUTION:
● Do not touch the glass of bulb directly by hand. Keep
grease and other oily substances away from it. Do not C
touch bulb by hand while it is lit or right after being
turned off. Burning may result.
● Do not leave bulb out of fog lamp reflector for a long time D
because dust, moisture smoke, etc. may affect the perfor-
mance of fog lamp. When replacing bulb, be sure to
replace it with new one. LKIA0573E
E

Removal and Installation EKS00FVS

FRONT FOG LAMP F


The fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb.
CAUTION:
● Do not leave fog lamp assembly without bulb for a long period of time. Dust, moisture, smoke, etc. G
entering the fog lamp body may affect the performance. Remove the bulb from the headlamp
assembly just before replacement bulb is installed.
● Grasp only the plastic base when handling the bulb. Never touch the glass envelope. Touching the H
glass could significantly affect the bulb life and/or fog lamp performance.
Removal
1. Remove front portion of fender protector. Refer to EI-21, "Removal and Installation of Front Fender Pro- I
tector"
2. Disconnect fog lamp connector.
3. Remove fog lamp screws and pull fog lamp rearward out of front J
bumper.

LT

LKIA0574E
M

Installation
Installation is in the reverse order of removal.

Revision: September 2005 LT-63 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

TURN SIGNAL AND HAZARD WARNING LAMPS PFP:26120

Component Parts and Harness Connector Location EKS00FVT

WKIA4961E

1. BCM 2. Combination switch (lighting 3. Combination meter


M18, M19, M20 switch) M24
(view with instrument lower panel RH removed) M28
4. Hazard switch

System Description EKS00FVU

OUTLINE
Power is supplied at all times
● through 50A fusible link (letter g , located in the fuse and fusible link box)
● to BCM (body control module) terminal 70, and
● through 10A fuse [No. 19, located in the fuse block (J/B)]
● to combination meter terminal 3.
TURN SIGNAL OPERATION
When the ignition switch is in the ON or START position, power is supplied
● through 10A fuse [No. 1, located in the fuse block (J/B)]
● to BCM terminal 38, and
● through 10A fuse [No. 14, located in the fuse block (J/B)]
● to combination meter terminal 16.
Ground is supplied
● to BCM terminal 67 and
● to combination meter terminals 13 and 23
● through grounds M57, M61 and M79.
LH Turn
When the turn signal switch is moved to the left position, the BCM, interpreting it as turn signal is ON, outputs
turn signal from BCM terminal 60.
The BCM supplies power
● through BCM terminal 60
● to front turn signal lamp LH terminal 1
● through front turn signal lamp LH terminal 3
● to grounds E9, E15 and E24, and
● to rear combination lamp LH (turn signal) terminal 4
● through rear combination lamp LH (turn signal) terminal 5
● to grounds B7 and B19.

Revision: September 2005 LT-64 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

BCM sends signal to combination meter through CAN communication lines and turns on turn signal indicator
lamp within combination meter. A
RH Turn
When the turn signal switch is moved to the right position, the BCM, interpreting it as turn signal is ON, outputs
turn signal from BCM terminal 61. B
The BCM supplies power
● through BCM terminal 61
● to front turn signal lamp RH terminal 1 C
● through front turn signal lamp RH terminal 3
● to grounds E9, E15 and E24, and
D
● to rear combination lamp RH (turn signal) terminal 4
● through rear combination lamp RH (turn signal) terminal 5
● to grounds B117 and B132. E
BCM sends signal to combination meter through CAN communication lines, and turns on turn signal indicator
lamp within combination meter.
HAZARD LAMP OPERATION F
Power is supplied at all times
● through 50A fusible link (letter g , located in the fuse and fusible link box)
G
● to BCM terminal 70, and
● through 10A fuse [No. 19, located in the fuse block (J/B)]
● to combination meter terminal 3. H
Ground is supplied
● to BCM terminal 67 and
● to combination meter terminals 13 and 23 I
● through grounds M57, M61 and M79.
When the hazard switch is depressed, ground is supplied
● to BCM terminal 29 J
● through hazard switch terminal 2
● through hazard switch terminal 1
LT
● through grounds M57, M61 and M79.
When the hazard switch is depressed, the BCM, interpreting it as hazard warning lamps are ON, outputs turn
signal from BCM terminals 60 and 61.
The BCM supplies power L
● through BCM terminals 60 and 61
● to front turn signal lamp LH and RH terminal 1
M
● through front turn signal lamp LH and RH terminal 3
● to grounds E9, E15 and E24, and
● to rear combination lamp LH (turn signal) terminal 4
● through rear combination lamp LH (turn signal) terminal 5
● to grounds B7 and B19, and
● to rear combination lamp RH (turn signal) terminal 4
● through rear combination lamp RH (turn signal) terminal 5
● to grounds B117 and B132.
BCM sends signal to combination meter through CAN communication lines and turns on turn signal indicator
lamps within combination meter.
REMOTE KEYLESS ENTRY SYSTEM OPERATION
Power is supplied at all times
● through 50A fusible link (letter g , located in the fuse and fusible link box)
● to BCM terminal 70, and

Revision: September 2005 LT-65 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

● through 10A fuse [No. 19, located in the fuse block (J/B)]
● to combination meter terminal 3.
Ground is supplied
● to BCM terminal 67 and
● to combination meter terminals 13 and 23
● through grounds M57, M61 and M79.
When the remote keyless entry system is triggered by input from the keyfob, the BCM, interpreting it as turn
signal is ON, outputs turn signal from BCM terminals 60 and 61.
The BCM supplies power
● through BCM terminals 60 and 61
● to front turn signal lamp LH and RH terminal 1
● through front turn signal lamp LH and RH terminal 3
● to grounds E9, E15 and E24, and
● to rear combination lamp LH (turn signal) terminal 4
● through rear combination lamp LH (turn signal) terminal 5
● to grounds B7 and B19, and
● to rear combination lamp RH (turn signal) terminal 4
● through rear combination lamp RH (turn signal) terminal 5
● to grounds B117 and B132.
BCM sends signal to combination meter through CAN communication lines, and turns on turn signal indicator
lamps within combination meter.
With power and input supplied, the BCM controls the flashing of the hazard warning lamps when keyfob is
used to activate the remote keyless entry system.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
CAN Communication System Description EKS00FVV

Refer to LAN-25, "CAN COMMUNICATION" .

Revision: September 2005 LT-66 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

Wiring Diagram — TURN — EKS00FVW

LT

WKWA4228E

Revision: September 2005 LT-67 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

WKWA4307E

Revision: September 2005 LT-68 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

Terminals and Reference Values for BCM EKS00FVX

A
Refer to BCS-12, "Terminals and Reference Values for BCM" .
How to Proceed With Trouble Diagnosis EKS00FVY

1. Confirm the symptom or customer complaint. B


2. Understand operation description and function description. Refer to LT-64, "System Description" .
3. Perform preliminary check. Refer to LT-69, "Preliminary Check" .
C
4. Check symptom and repair or replace the cause of malfunction.
5. Do turn signal and hazard warning lamps operate normally? If YES: GO TO 6. If NO: GO TO 4.
6. Inspection End. D
Preliminary Check EKS00FVZ

CHECK POWER SUPPLY AND GROUND CIRCUIT


Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" . E

CONSULT-II Function (BCM) EKS00FW0

CONSULT-II can display each diagnostic item using the diagnostic test modes shown following. F
BCM diagnostic
Diagnostic mode Description
test item
Supports inspections and adjustments. Commands are transmitted to the BCM G
WORK SUPPORT for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time. H
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
Inspection by part
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
I

ECU PART NUMBER BCM part number can be read.


CONFIGURATION Performs BCM configuration read/write functions. J

CONSULT-II OPERATION
CAUTION: LT
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON-
L
SULT-II CONVERTER to the data link connector, then turn igni-
tion switch ON.

BBIA0538E

Revision: September 2005 LT-69 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

2. Touch "START (NISSAN BASED VHCL)".

BCIA0029E

3. Touch "BCM" on "SELECT SYSTEM" screen.


If "BCM" is not indicated, go to GI-40, "CONSULT-II Data Link
Connector (DLC) Circuit" .

BCIA0030E

4. Touch "FLASHER" on "SELECT TEST ITEM" screen.

LKIA0183E

DATA MONITOR
Operation Procedure
1. Touch "FLASHER" on "SELECT TEST ITEM" screen.
2. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
3. Touch either "ALL SIGNALS" or "SELECTION FROM MENU" on the "SELECT MONITOR ITEM" screen.

ALL SIGNALS Monitors all the signals.


SELECTION FROM MENU Selects and monitors the individual signal.

4. Touch "START".
5. When "SELECTION FROM MENU" is selected, touch items to be monitored. When "ALL SIGNALS" is
selected, all the items will be monitored.
6. Touch "RECORD" while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch "STOP".
Display Item List
Monitor item Contents
Displays "IGN position (ON)/OFF, ACC position (OFF)" judged from the ignition switch
IGN ON SW "ON/OFF"
signal.
Displays "Hazard ON (ON)/Hazard OFF (OFF)" status, determined from hazard switch
HAZARD SW "ON/OFF"
signal.

Revision: September 2005 LT-70 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

Monitor item Contents


A
TURN SIGNAL R "ON/OFF" Displays "Turn right (ON)/Other (OFF)" status, determined from lighting switch signal.
TURN SIGNAL L "ON/OFF" Displays "Turn left (ON)/Other (OFF)" status, determined from lighting switch signal.
BRAKE SW "ON/OFF" Displays status of stop lamp switch. B
ACTIVE TEST
Operation Procedure
1. Touch "FLASHER" on "SELECT TEST ITEM" screen. C
2. Touch "ACTIVE TEST" on "SELECT DIAG MODE" screen.
3. Touch item to be tested and check operation of the selected item.
D
4. During the operation check, touching "BACK" or "OFF" deactivates the operation.
Display Item List
Test item Description E
FLASHER (RH) Turn signal lamp (right) can be operated by any ON-OFF operations.
FLASHER (LH) Turn signal lamp (left) can be operated by any ON-OFF operations.
F
Turn Signal Lamp Does Not Operate EKS00FW1

1. CHECK COMBINATION SWITCH INPUT SIGNAL G


With CONSULT-II
Select "BCM" on CONSULT-II. With "FLASHER" data monitor, make
sure "TURN SIGNAL R" and "TURN SIGNAL L" turns ON-OFF H
linked with operation of lighting switch.
When lighting switch is in : TURN SIGNAL R ON
TURN RH position I
When lighting switch is in : TURN SIGNAL L ON
TURN LH position
J
Without CONSULT-II
Refer to LT-82, "Combination Switch Inspection" .
SKIA4499E
OK or NG
LT
OK >> GO TO 2.
NG >> Check lighting switch. Refer to LT-82, "Combination Switch Inspection" .

2. ACTIVE TEST L

With CONSULT-II
1. Select "FLASHER" during active test. Refer to LT-71, "ACTIVE M
TEST" .
2. Make sure "FLASHER RH" and "FLASHER LH" operate.
Without CONSULT-II
GO TO 3.
OK or NG
OK >> Replace BCM. Refer to BCS-27, "Removal and Installa-
tion" .
NG >> GO TO 3.
SKIA6190E

Revision: September 2005 LT-71 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

3. CHECK TURN SIGNAL LAMPS CIRCUIT


1. Turn ignition switch OFF.
2. Disconnect BCM connector and front turn signal lamp LH and
RH connectors.
3. Check continuity between BCM harness connector M20 terminal
60 and front turn signal lamp LH harness connector E27 termi-
nal 1.
60 - 1 : Continuity should exist.
4. Check continuity between BCM harness connector M20 terminal
61 and front turn signal lamp RH harness connector E111 termi-
nal 1. WKIA3308E

61 - 1 : Continuity should exist.


OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.

4. CHECK GROUND
1. Check continuity between front turn signal lamp LH harness
connector E27 terminal 3 and ground.
3 - Ground : Continuity should exist.
2. Check continuity between front turn signal lamp RH harness
connector E111 terminal 3 and ground.
3 - Ground : Continuity should exist.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector. WKIA3309E

5. CHECK BULB
Check bulb standard of each turn signal lamp is correct. Refer to LT-151, "Exterior Lamp" .
OK or NG
OK >> Replace BCM if turn signal lamps do not work after setting the connector again. Refer to BCS-27,
"Removal and Installation" .
NG >> Replace turn signal lamp bulb. Refer to LT-27, "FRONT TURN SIGNAL/PARKING LAMP" .
Rear Turn Signal Lamp Does Not Operate EKS00FW2

1. CHECK TAIL LAMPS AND STOP LAMPS


Check bulb standard of each turn signal lamp is correct. Refer to LT-151, "Exterior Lamp" .
OK or NG
OK >> GO TO 2.
NG >> Replace turn signal lamp bulb. Refer to LT-105, "Bulb Replacement" .

Revision: September 2005 LT-72 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

2. CHECK TURN SIGNAL LAMPS CIRCUIT A


1. Disconnect BCM connector and rear combination lamp connec-
tor.
2. Check continuity between BCM harness connector M20 terminal B
61 and rear combination lamp RH harness connector B105 ter-
minal 4.
61 - 4 : Continuity should exist. C

3. Check continuity between BCM harness connector M20 terminal


60 and rear combination lamp LH harness connector B35 termi-
nal 4. D
WKIA3310E
60 - 4 : Continuity should exist.
OK or NG E
OK >> GO TO 3.
NG >> Repair harness or connector.
F
3. CHECK GROUND CIRCUIT
Check continuity between rear combination lamp harness connector
B35 (LH) and B105 (RH) terminal 5 and ground. G

5 - Ground : Continuity should exist.


OK or NG H
OK >> Check rear combination lamp connector for proper con-
nection. Repair as necessary.
NG >> Repair harness or connector. I

WKIA3311E
J
Hazard Warning Lamp Does Not Operate But Turn Signal Lamps Operate EKS00FW3

1. CHECK BULB
LT
Make sure bulb standard of each turn signal lamp is correct. Refer to LT-151, "Exterior Lamp" .
OK or NG
OK >> GO TO 2. L
NG >> Replace turn signal lamp bulb. Refer to LT-27, "FRONT TURN SIGNAL/PARKING LAMP" for
front turn signal bulb. Refer to LT-105, "Bulb Replacement" for rear turn signal bulb.
M

Revision: September 2005 LT-73 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

2. CHECK HAZARD SWITCH INPUT SIGNAL


With CONSULT-II
Select "BCM" on CONSULT-II. With "FLASHER" data monitor, make
sure "HAZARD SW" turns ON-OFF linked with operation of hazard
switch.
When hazard switch is in : HAZARD SW ON
ON position

SKIA4500E

Without CONSULT-II
Check voltage between BCM harness connector M18 terminal 29
and ground.
BCM
Voltage
(+) (–) Condition
(Approx.)
Connector Terminal
Hazard switch is ON 0V
M18 29 Ground
Hazard switch is OFF 5V
OK or NG
WKIA1969E
OK >> Replace BCM. Refer to BCS-27, "Removal and Installa-
tion" .
NG >> GO TO 3.

3. CHECK HAZARD SWITCH CIRCUIT


1. Turn ignition switch OFF.
2. Disconnect BCM connector and hazard switch connector.
3. Check continuity between BCM harness connector M18 terminal
29 and hazard switch harness connector M55 terminal 2.
29 - 2 : Continuity should exist.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
SKIA5912E

4. CHECK GROUND
Check continuity between hazard switch harness connector M55 ter-
minal 1 and ground.
1 - Ground : Continuity should exist.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.

SKIA8972E

Revision: September 2005 LT-74 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

5. CHECK HAZARD SWITCH A


1. Disconnect hazard switch connector.
2. Check continuity of hazard switch.
B
Hazard switch
Condition Continuity
Terminal
Hazard switch is ON Yes C
2 1
Hazard switch is OFF No

OK or NG D
OK >> Replace BCM if hazard warning lamps do not work after PKIA4601E
setting the connector again. Refer to BCS-27, "Removal
and Installation" .
E
NG >> Replace hazard switch. Refer to LT-78, "Removal and Installation" .
Turn Signal Indicator Lamp Does Not Operate EKS00FW4

1. CHECK CAN COMMUNICATION SYSTEM F

Check CAN communication. Refer to LAN-25, "CAN COMMUNICATION" .


OK or NG G
OK >> Replace combination meter. Refer to IP-14, "COMBINATION METER" .
NG >> Repair as necessary.
H

LT

Revision: September 2005 LT-75 2006 Pathfinder


TURN SIGNAL AND HAZARD WARNING LAMPS

Bulb Replacement EKS00FW5

FRONT TURN SIGNAL LAMP


Refer to LT-27, "FRONT TURN SIGNAL/PARKING LAMP" .
REAR TURN SIGNAL LAMP
Refer to LT-105, "Bulb Replacement" .

Removal and Installation EKS00FW7

FRONT TURN SIGNAL LAMP


Refer to LT-27, "Removal and Installation" .
REAR TURN SIGNAL LAMP
Refer to LT-105, "Removal and Installation" .

Revision: September 2005 LT-76 2006 Pathfinder


LIGHTING AND TURN SIGNAL SWITCH

LIGHTING AND TURN SIGNAL SWITCH PFP:25540


A
Removal and Installation EKS00FW9

REMOVAL
1. Remove instrument lower cover LH. Refer to IP-14, "LOWER INSTRUMENT PANEL LH" .
B
2. Remove steering column cover.
3. Disconnect the lighting and turn signal switch connector.
4. While pressing tabs, pull lighting and turn signal switch toward C
driver door and release from the steering column.

E
LKIA0013E

INSTALLATION
Installation is in the reverse order of removal. F

LT

Revision: September 2005 LT-77 2006 Pathfinder


HAZARD SWITCH

HAZARD SWITCH PFP:25290

Removal and Installation EKS00FWA

REMOVAL
1. Remove cluster lid C. Refer to IP-11, "CLUSTER LID C -WITHOUT NAVIGATION SYSTEM" .
2. Disconnect the hazard switch connector.
3. Remove the screws and remove the hazard switch.

LKIA0575E

INSTALLATION
Installation is in the reverse order of removal.

Revision: September 2005 LT-78 2006 Pathfinder


COMBINATION SWITCH

COMBINATION SWITCH PFP:25567


A
Wiring Diagram — COMBSW — EKS00FWB

LT

WKWA4229E

Revision: September 2005 LT-79 2006 Pathfinder


COMBINATION SWITCH

Combination Switch Reading Function EKS00FWC

For details, refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .


CONSULT-II Function (BCM) EKS00FWD

CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
BCM diagnostic
Diagnostic mode Description
test item
Supports inspections and adjustments. Commands are transmitted to the BCM
WORK SUPPORT for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
Inspection by part
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.

CONSULT-II OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, then turn igni-
tion switch ON.

BBIA0538E

2. Touch "START (NISSAN BASED VHCL)".

BCIA0029E

3. Touch "BCM" on "SELECT SYSTEM" screen.


If "BCM" is not indicated, go to GI-40, "CONSULT-II Data Link
Connector (DLC) Circuit" .

BCIA0030E

Revision: September 2005 LT-80 2006 Pathfinder


COMBINATION SWITCH

4. Touch "COMB SW" on "SELECT TEST ITEM" screen.


A

LKIA0183E
D
DATA MONITOR
Operation Procedure
1. Touch "COMB SW" on "SELECT TEST ITEM" screen. E
2. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
3. Touch either "ALL SIGNALS" or "SELECTION FROM MENU" on "SELECT MONITOR ITEM" screen.
F
ALL SIGNALS Monitors all the signals.
SELECTION FROM MENU Selects and monitors individual signal.

4. Touch "START". G
5. When "SELECTION FROM MENU" is selected, touch items to be monitored. When "ALL SIGNALS" is
selected, all the signals will be monitored.
H
6. Touch "RECORD" while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch "STOP".
Display Item List I
Monitor item name
Contents
"OPERATION OR UNIT"
TURN SIGNAL R "ON/OFF" Displays "Turn Right (ON)/Other (OFF)" status, determined from lighting switch signal. J
TURN SIGNAL L "ON/OFF" Displays "Turn Left (ON)/Other (OFF)" status, determined from lighting switch signal.
Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from lighting
HI BEAM SW "ON/OFF"
switch signal. LT
HEAD LAMP SW 1 "ON/OFF" Displays "Headlamp switch 1 (ON)/Other (OFF)" status, determined from lighting switch signal.
Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from lighting
HEAD LAMP SW 2 "ON/OFF" L
switch signal.
Displays status (lighting switch 1st position: ON/Others: OFF) of lighting switch judged from lighting
LIGHT SW 1ST "ON/OFF"
switch signal.
Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from lighting M
PASSING SW "ON/OFF"
switch signal.
AUTO LIGHT SW "ON/OFF" Displays "Auto light switch (ON)/Other (OFF)" status, determined from lighting switch signal.
FR FOG SW "ON/OFF" Displays "Front fog lamp switch (ON)/Other (OFF)" status, determined from lighting switch signal.
FR WIPER HI "ON/OFF" Displays "Front Wiper HI (ON)/Other (OFF)" status, determined from wiper switch signal.
FR WIPER LOW "ON/OFF" Displays "Front Wiper LOW (ON)/Other (OFF)" status, determined from wiper switch signal.
FR WIPER INT "ON/OFF" Displays "Front Wiper INT (ON)/Other (OFF)" status, determined from wiper switch signal.
FR WASHER SW "ON/OFF" Displays "Front Washer Switch (ON)/Other (OFF)" status, determined from wiper switch signal.
INT VOLUME [1 - 7] Displays intermittent operation knob setting (1 - 7), determined from wiper switch signal.
RR WIPER ON "ON/OFF" Displays "Rear Wiper (ON)/(OFF)" status, determined from wiper switch signal.
RR WIPER INT "ON/OFF" Displays "Rear Wiper INT (ON)/(OFF)" status, determined from wiper switch signal.
RR WASHER SW "ON/OFF" Displays "Rear Washer (ON)/(OFF)" status, determined from wiper switch signal.

Revision: September 2005 LT-81 2006 Pathfinder


COMBINATION SWITCH

Combination Switch Inspection EKS00FWE

1. SYSTEM CHECK
Referring to table below, check to which system the malfunctioning switch belongs.
System 1 System 2 System 3 System 4 System 5
— FR WASHER FR WIPER LO TURN LH TURN RH
FR WIPER HI — FR WIPER INT PASSING HEAD LAMP1
INT VOLUME 1 RR WASHER — HEAD LAMP2 HI BEAM
RR WIPER INT INT VOLUME 3 AUTO LIGHT — TAIL LAMP
INT VOLUME 2 RR WIPER ON — FR FOG —

>> GO TO 2.

2. SYSTEM CHECK
With CONSULT-II
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. Connect CONSULT-II, and select "COMB SW" on "SELECT
TEST ITEM" screen.
2. Select "DATA MONITOR".
3. Select "START", and confirm that other switches in malfunction-
ing system operate normally.
Example: When auto light switch is malfunctioning, confirm that
"FRONT WIPER LOW" and "FRONT WIPER INT" in System 3,
to which the auto light switch belongs, turn ON-OFF normally.

SKIA7075E

Without CONSULT-II
Operate combination switch, and confirm that other switches in malfunctioning system operate normally.
Example: When auto light switch is malfunctioning, confirm that "FRONT WIPER LOW" and "FRONT WIPER
INT" in System 3, to which the auto light switch belongs, operate normally.
Check results
Other switches in malfunctioning system operate normally.>>Replace lighting switch or wiper switch.
Other switches in malfunctioning system do not operate normally.>>GO TO 3.

Revision: September 2005 LT-82 2006 Pathfinder


COMBINATION SWITCH

3. HARNESS INSPECTION A
1. Turn ignition switch OFF.
2. Disconnect BCM and combination switch connectors.
3. Check for continuity between BCM harness connector of the suspect system and the corresponding com- B
bination switch connector terminals.
Sus- BCM Combination switch
C
pect Continuity
system Connector Terminal Connector Terminal

Input 1 6 10
1 D
Output 1 36 13
Input 2 5 15
2
Output 2 35 12 E
Input 3 4 5
3 M18 M28 Yes
Output 3 34 16 WKIA4021E

F
Input 4 3 6
4
Output 4 33 11
Input 5 2 7 G
5
Output 5 32 14
4. Check for continuity between each terminal of BCM harness connector in suspect malfunctioning system
and ground. H

Suspect BCM
Continuity
system Connector Terminal I
Input 1 6
1
Output 1 36
Input 2 5 J
2
Output 2 35
Input 3 4
3 M18 Ground No LT
Output 3 34
Input 4 3
4
Output 4 33 L
Input 5 2
5
Output 5 32
M
OK or NG
OK >> GO TO 4.
NG >> Check harness between BCM and combination switch for open or short circuit.

Revision: September 2005 LT-83 2006 Pathfinder


COMBINATION SWITCH

4. BCM OUTPUT TERMINAL INSPECTION


1. Connect BCM and combination switch connectors.
2. Turn lighting switch and wiper switch to OFF.
3. Set wiper dial to position 4.
4. Turn ignition switch ON, and check combination switch input
(BCM output) terminal voltage waveform of suspect malfunction-
ing system.
Combination switch
Suspect system (+)
Connector Terminal
1 Input 1 13
2 Input 2 12
3 M28 Input 3 16
4 Input 4 11
5 Input 5 14
OK or NG
OK >> Open circuit in combination switch, GO TO 5.
NG >> Replace BCM. Refer to BCS-27, "Removal and Installa-
tion" .

WKIA3960E

5. COMBINATION SWITCH INSPECTION


Referring to table below, perform combination switch inspection.
Procedure
1 2 3 4 5 6 7

Replace Confirm OK INSPECTION END Confirm OK INSPECTION END Confirm OK INSPECTION END
lighting check Replace wiper check Replace switch check Confirm symptom
switch. results. NG results. NG results. NG
switch. base. again.

>> Inspection End.


Removal and Installation EKS00FWF

For details, refer to LT-77, "Removal and Installation" .


Switch Circuit Inspection EKS00FWG

For details, refer to LT-82, "Combination Switch Inspection" .

Revision: September 2005 LT-84 2006 Pathfinder


STOP LAMP

STOP LAMP PFP:26550


A
System Description EKS00FWH

Power is supplied at all times


● through 10A fuse [No. 20, located in fuse block (J/B)] B
● to stop lamp switch terminal 1, and
● to stop lamp relay terminals 2 and 3 (with hill descent control and hill start assist).
When the brake pedal is pressed, the stop lamp switch is closed and power is supplied C
● through stop lamp switch terminal 2
● to rear combination lamp LH and RH terminal 2
D
● to high-mounted stop lamp terminal 1
● to ABS actuator and electric unit (control unit) terminal 41.
Ground is supplied E
● to rear combination lamp LH terminal 5
● through grounds B7 and B19, and
● to high-mounted stop lamp terminal 2 F
● through grounds D406 and D504, and
● to rear combination lamp RH terminal 5
● through grounds B117 and B132. G
With power and ground supplied, the stop lamps illuminate.
H

LT

Revision: September 2005 LT-85 2006 Pathfinder


STOP LAMP

Wiring Diagram — STOP/L — EKS00FWI

WKWA4341E

Revision: September 2005 LT-86 2006 Pathfinder


STOP LAMP

High-Mounted Stop Lamp EKS00FWJ

BULB REPLACEMENT A
The high-mounted stop lamp bulbs are not serviceable.
REMOVAL AND INSTALLATION
B
Removal
1. Remove back door window garnish.
2. Disconnect high-mounted stop lamp connector. C
3. Remove nuts and remove high-mounted stop lamp.

F
LKIA0576E

Installation
G
Installation is in the reverse order of removal.
Stop Lamp EKS00FWK

BULB REPLACEMENT H
Refer to LT-105, "Bulb Replacement" .
REMOVAL AND INSTALLATION
Refer to LT-105, "Removal and Installation" . I

LT

Revision: September 2005 LT-87 2006 Pathfinder


BACK-UP LAMP

BACK-UP LAMP PFP:26550

Wiring Diagram — BACK/L — EKS00FWL

WKWA4230E

Revision: September 2005 LT-88 2006 Pathfinder


BACK-UP LAMP

Bulb Replacement EKS00FWM

A
Refer to LT-105, "Bulb Replacement" .
Removal and Installation EKS00FWN

Refer to LT-105, "Removal and Installation" . B

LT

Revision: September 2005 LT-89 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

PARKING, LICENSE PLATE AND TAIL LAMPS PFP:26550

Component Parts and Harness Connector Location EKS00FWO

WKIA4963E

1. IPDM E/R 2. BCM 3. Combination switch (lighting switch)


E118, E119, E120, E121, M18, M19, M20 M28
E122, E123, E124 (view with instrument lower panel LH removed)
4. Combination meter
M24

System Description EKS00FWP

Control of the parking, front side marker, license plate, and tail lamp operation is dependent upon the position
of the lighting switch (combination switch). When the lighting switch is placed in the 1ST position, the BCM
(body control module) receives input signal requesting the parking, front side marker, license plate and tail
lamps to illuminate. This input signal is communicated to the IPDM E/R (intelligent power distribution module
engine room) across the CAN communication lines. The CPU (central processing unit) of the IPDM E/R con-
trols the tail lamp relay coil. This relay, when energized, directs power to the parking, front side marker, license
plate and tail lamps, which then illuminate.
Power is supplied at all times
● to ignition relay, located in the IPDM E/R, and
● to tail lamp relay, located in the IPDM E/R, and
● through 20A fuse (No. 53, located in the IPDM E/R)
● to CPU of the IPDM E/R, and
● through 50A fusible link (letter g , located in the fuse and fusible link box)
● to BCM terminal 70.
With the ignition switch in the ON or START position, power is supplied
● to ignition relay, located in the IPDM E/R.
● through 10A fuse [No. 1, located in the fuse block (J/B)]
● to BCM terminal 38 and
Ground is supplied
● to BCM terminal 67
● through grounds M57, M61 and M79, and
● to IPDM E/R terminals 38 and 59
● through grounds E9, E15 and E24.
OPERATION BY LIGHTING SWITCH
With the lighting switch in the 1ST or 2ND position (or if the auto light system is activated), the BCM receives
input signal requesting the parking, front side marker, license plate and tail lamps to illuminate. This input sig-
nal is communicated to the IPDM E/R across the CAN communication lines. The CPU in the IPDM E/R con-
trols the tail lamp relay coil, which when energized, directs power

Revision: September 2005 LT-90 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

● through 10A fuse (No. 37, located in the IPDM E/R)


● through IPDM E/R terminal 57 A
● to license plate lamp LH and RH terminal 1
● to rear combination lamp LH and RH (tail/side marker) terminal 1, and
B
● through 10A fuse (No. 36, located in the IPDM E/R)
● through IPDM E/R terminals 28 and 49
● to front side marker lamp LH and RH terminal 1 C
● to front parking lamp LH and RH terminal 2.
Ground is supplied
● to front side marker lamp LH and RH terminal 2 D
● to front parking lamp LH and RH terminal 3
● through grounds E9, E15 and E24, and
● to license plate lamp LH and RH terminal 2 E
● through grounds D406 and D504, and
● to rear combination lamp LH (tail/side marker) terminal 5
F
● through grounds B7 and B19, and
● to rear combination lamp RH (tail/side marker) terminal 5
● through grounds B117 and B132. G
With power and ground supplied, the parking, side marker, license plate and tail lamps illuminate.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" . H

EXTERIOR LAMP BATTERY SAVER CONTROL


When the combination switch (lighting switch) is in the 1ST (or 2ND) position, and the ignition switch is turned I
from ON or ACC to OFF, the battery saver control feature is activated.
Under this condition, the parking, front side marker, license and tail lamps remain illuminated for 5 minutes,
then the parking, front side marker, license plate and tail lamps are turned off.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II. J

CAN Communication System Description EKS00FWQ

Refer to LAN-25, "CAN COMMUNICATION" . LT

Revision: September 2005 LT-91 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

Schematic EKS00FWR

WKWA4308E

Revision: September 2005 LT-92 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

Wiring Diagram — TAIL/L — EKS00FWS

LT

WKWA4231E

Revision: September 2005 LT-93 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

WKWA3087E

Revision: September 2005 LT-94 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

LT

WKWA2039E

Revision: September 2005 LT-95 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

WKWA4342E

Revision: September 2005 LT-96 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

Terminals and Reference Values for BCM EKS00FWT

A
Refer to BCS-12, "Terminals and Reference Values for BCM" .
Terminals and Reference Values for IPDM E/R EKS00FWU

Refer to PG-28, "Terminals and Reference Values for IPDM E/R" . B

How to Proceed With Trouble Diagnosis EKS00FWV

1. Confirm the symptom or customer complaint. C


2. Understand operation description and function description. Refer to LT-90, "System Description" .
3. Carry out the Preliminary Check. Refer to LT-97, "Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction. D
5. Do the parking, front side marker, license and tail lamps operate normally? If YES: GO TO 6. If NO: GO
TO 4.
6. Inspection End. E

Preliminary Check EKS00FWW

CHECK POWER SUPPLY AND GROUND CIRCUIT F


Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" and PG-30, "IPDM E/R Power/Ground Cir-
cuit Inspection" .
CONSULT-II Functions EKS00FWX G
Refer to LT-12, "CONSULT-II Function (BCM)" in HEADLAMP (FOR USA).
Refer to LT-15, "CONSULT-II Function (IPDM E/R)" in HEADLAMP (FOR USA).
H
Parking, Side Marker, License Plate and/or Tail Lamps Do Not Illuminate EKS00FWY

1. CHECK COMBINATION SWITCH INPUT SIGNAL


I
With CONSULT-II
Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor,
make sure "LIGHT SW 1ST" turns ON-OFF linked with operation of
J
lighting switch.
When lighting switch is in : LIGHT SW 1ST ON
1ST position
LT
Without CONSULT-II
Refer to LT-82, "Combination Switch Inspection" .
OK or NG L
OK >> GO TO 2.
NG >> Check lighting switch. Refer to LT-82, "Combination SKIA5956E

Switch Inspection" . M

Revision: September 2005 LT-97 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

2. ACTIVE TEST
With CONSULT-II
1. Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST"
on "SELECT DIAG MODE" screen.
2. Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
3. Touch "TAIL" on "ACTIVE TEST" screen.
4. Make sure parking, front side marker, license plate and tail lamp
operation.
Parking, front side marker, license plate and tail
lamp should operate
Without CONSULT-II WKIA1438E

1. Start auto active test. Refer to PG-24, "Auto Active Test" .


2. Make sure parking, front side marker, license plate and tail lamp operation.
Parking, front side marker, license plate and tail
lamp should operate
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.

3. CHECK IPDM E/R


1. Select "IPDM E/R" on CONSULT-II, and select "DATA MONI-
TOR" on "SELECT DIAG MODE" screen.
2. Make sure "TAIL&CLR REQ" turns ON when lighting switch is in
1ST position.
When lighting switch is in : TAIL&CLR REQ ON
1ST position
OK or NG
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and
Installation of IPDM E/R" .
NG >> Replace BCM. Refer to BCS-27, "Removal and Installa- SKIA5958E

tion" .

Revision: September 2005 LT-98 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

4. CHECK INPUT SIGNAL A


With CONSULT-II
1. Turn ignition switch OFF.
B
2. Disconnect front parking lamp, front side marker lamp, license plate lamp and rear combination lamp con-
nectors.
3. Turn ignition switch ON.
C
4. Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST" on "SELECT DIAG MODE" screen.
5. Select "TAIL LAMP" on "SELECT TEST ITEM" screen.
6. Touch "ON" on "ACTIVE TEST" screen. D
7. When tail lamp is operating, check voltage between front parking lamp, front side marker lamp, license
plate lamp, rear combination lamp harness connector and ground.
Without CONSULT-II E
1. Start auto active test. Refer to PG-24, "Auto Active Test" .
2. When tail lamp is operating, check voltage between front side marker lamp, front parking lamp, license
plate lamp, rear combination lamp harness connector and ground. F
Front side marker lamp
(+) (–) Voltage
G
Connector Terminal
LH E17
1 Ground Battery voltage
RH E108 H

I
WKIA3508E

Front parking lamp


J

(+) (–) Voltage


Connector Terminal LT
LH E27
2 Ground Battery voltage
RH E111
L

WKIA3509E
M

License plate lamp


(+) (–) Voltage
Connector Terminal
LH D506
1 Ground Battery voltage
RH D507

WKIA3315E

Revision: September 2005 LT-99 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

Rear combination lamp


(+) (–) Voltage
Connector Terminal
LH B35
1 Ground Battery voltage
RH B105
OK or NG
OK >> GO TO 6.
NG >> GO TO 5.
WKIA3316E

Revision: September 2005 LT-100 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

5. CHECK PARKING, SIDE MARKER, LICENSE PLATE AND TAIL LAMP CIRCUIT A
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and B
front side marker lamp harness connector.
IPDM E/R Front side marker lamp
Continuity C
Connector Terminal Connector Terminal
E121 28 LH E17
1 Yes
E123 49 RH E108 D

WKIA3512E

I
4. Check continuity between IPDM E/R harness connector and
front parking lamp harness connector.
IPDM E/R Front parking lamp J
Continuity
Connector Terminal Connector Terminal
E121 28 LH E27
2 Yes LT
E123 49 RH E111

WKIA3513E

Revision: September 2005 LT-101 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

5. Check continuity between IPDM E/R harness connector and


license plate lamp harness connector.
IPDM E/R License plate lamp
Continuity
Connector Terminal Connector Terminal
LH D506
E124 57 1 Yes
RH D507

WKIA3318E

6. Check continuity between IPDM E/R harness connector and


rear combination lamp harness connector.
IPDM E/R Rear combination lamp
Continuity
Connector Terminal Connector Terminal
LH B35
E124 57 1 Yes
RH B105

OK or NG
OK >> Replace IPDM E/R. Refer to PG-32, "Removal and
Installation of IPDM E/R" . WKIA3319E

NG >> Repair harness or connector.

Revision: September 2005 LT-102 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

6. CHECK GROUND A
1. Turn ignition switch OFF.
2. Check continuity between front side marker lamp harness con-
nector and ground. B

Front side marker lamp


Continuity
Connector Terminal C
LH E17
2 Ground Yes
RH E108
D

WKIA3516E
E
3. Check continuity between front parking lamp harness connector
and ground.
F
Front parking lamp
Continuity
Connector Terminal
LH E27 G
3 Ground Yes
RH E111

H
WKIA3517E

4. Check continuity between license plate lamp harness connector I


and ground.
License plate lamp
Continuity J
Connector Terminal
LH D506
2 Ground Yes
RH D507 LT

WKIA3321E L

5. Check continuity between rear combination lamp harness con-


nector and ground. M
Rear combination lamp
Continuity
Connector Terminal
LH B35
5 Ground Yes
RH B105
OK or NG
OK >> Check bulbs.
NG >> Repair harness or connector. WKIA3322E

Revision: September 2005 LT-103 2006 Pathfinder


PARKING, LICENSE PLATE AND TAIL LAMPS

Parking, Side Marker, License Plate and Tail Lamps Do Not Turn OFF (After
Approx. 10 Minutes) EKS00FWZ

1. CHECK IPDM E/R


1. Turn ignition switch ON. Turn the combination switch (lighting switch) to the OFF position. Turn ignition
switch OFF.
2. Verify that the parking, front side marker, license plate and tail lamps turn on and off after approximately
10 minutes.
OK or NG
OK >> Ignition relay malfunction. Refer to PG-19, "Function of Detecting Ignition Relay Malfunction" .
NG >> Inspection End.
Bulb Replacement EKS00FX0

FRONT PARKING LAMP


Refer to LT-27, "FRONT TURN SIGNAL/PARKING LAMP" .
TAIL LAMP
For bulb replacement, refer to LT-105, "Bulb Replacement" .
LICENSE PLATE LAMP
Removal
1. Remove back door finisher. Refer to EI-35, "BACK DOOR TRIM" .
2. Turn bulb socket counterclockwise and remove bulb socket.
3. Remove license plate lamp bulb.
Installation
Installation is in the reverse order of removal.

Removal and Installation EKS00HJU

LICENSE PLATE LAMP


Removal
1. Remove license lamp finisher. Refer to EI-19, "LICENSE LAMP FINISHER" .
2. Disconnect license plate lamp harness connector.
3. Remove license plate lamp screw and remove license plate lamp.
Installation
Installation is in the reverse order of removal.

Revision: September 2005 LT-104 2006 Pathfinder


REAR COMBINATION LAMP

REAR COMBINATION LAMP PFP:26554


A
Bulb Replacement EKS00FX2

REMOVAL
1. Remove rear combination lamp bolts.
B
2. Pull rear combination lamp to remove from the vehicle.
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb. C

WKIA4168E
E
INSTALLATION
Installation is in the reverse order of removal.
F
Removal and Installation EKS00FX3

REMOVAL
1. Remove rear combination lamp bolts.
G
2. Pull rear combination lamp to remove from the vehicle.
3. Disconnect rear combination lamp connector.
INSTALLATION H
Installation is in the reverse order of removal.

LT

Revision: September 2005 LT-105 2006 Pathfinder


TRAILER TOW

TRAILER TOW PFP:93020

Component Parts and Harness Connector Location EKS00FX4

WKIA4962E

1. IPDM E/R 2. Trailer tow relays 3. BCM


E118, E119, E120, E121, E140, E148 M18, M19, M20
E122, E123, E124 (view with instrument lower panel LH removed)
4. Electric brake (pre-wiring) 5. Combination switch (lighting switch) 6. Combination meter
M76 M28 M24
7. Trailer connector
C126

System Description EKS00FX5

Power is supplied at all times


● to ignition relay, located in the IPDM E/R (intelligent power distribution module engine room), and
● to tail lamp relay, located in the IPDM E/R, and
● through 50A fusible link (letter g , located in the fuse and fusible link box)
● to BCM (body control module) terminal 70, and
● to 15A fuse (No. 60, located in the fuse and relay box), and
● to trailer turn relay RH and LH terminal 5, and
● through 20A fuse (No. 53, located in the IPDM E/R)
● to CPU of the IPDM E/R, and
● through 10A fuse (No. 32, located in the IPDM E/R)
● to IPDM E/R terminal 61
● to trailer tow relay 1 terminal 3, and
● through 30A fusible link (letter m , located in the fuse and fusible link box)
● to trailer tow relay 2 terminals 3 and 6, and
● through 30A fusible link (letter h , located in the fuse and fusible link box)
● to electric brake (pre-wiring) terminal 5.

Revision: September 2005 LT-106 2006 Pathfinder


TRAILER TOW

With the ignition switch in the ON or START position, power is supplied


● to ignition relay, located in the IPDM E/R, and A
● through 10A fuse [No. 1, located in the fuse block (J/B)]
● to BCM terminal 38, and
B
● through 10A fuse (No. 38, located in the IPDM E/R)
● to IPDM E/R terminal 27, and
● to trailer tow relay 2 terminal 1. C
Ground is supplied
● to BCM terminal 67 and
● to electric brake (pre-wiring) terminal 1 D
● through grounds M57, M61 and M79, and
● to IPDM E/R terminals 38 and 59
● to trailer tow relay 1 terminal 2 E
● to trailer tow relay 2 terminal 2
● to trailer connector terminal 1 (trailer tow 7 pin) or terminal 4 (trailer tow 4 pin), and
F
● to trailer turn relay RH and LH terminal 2
● through grounds E9, E15 and E24.
TRAILER TAIL LAMP OPERATION G
The trailer tail lamps are controlled by the trailer tow relay 1.
With the lighting switch in the parking and tail lamp ON (1ST) position, AUTO position (and the auto light sys-
tem is activated) or headlamp ON (2ND) position, power is supplied from the tail lamp relay H
● through 10A fuse (No. 37, located in the IPDM E/R)
● through IPDM E/R terminal 29
● to trailer tow relay 1 terminal 1. I
When energized, trailer tow relay 1 tail lamp power is supplied
● through trailer tow relay 1 terminal 5
J
● to trailer connector terminal 3.
TRAILER STOP, TURN SIGNAL AND HAZARD LAMP OPERATION
The trailer stop, turn signal and hazard lamps are controlled by the BCM. If either turn signal or the hazard LT
lamps are turned on, the BCM supplies voltage to the trailer turn relay RH or LH to make them flash. If the
BCM receives stop lamp switch signal, the BCM supplies voltage to the trailer turn relay RH and LH to make
them illuminate.
Left stop, turn signal and hazard lamp output is supplied L
● through BCM terminal 52
● to trailer turn relay LH terminal 1
M
When energized, trailer turn relay LH supplies power to the left stop, turn signal, and hazard lamp
● through trailer turn relay LH terminal 3
● to trailer connector terminal 2 (trailer tow 7 pin) or terminal 1 (trailer tow 4 pin).
Right stop, turn signal and hazard lamp output is supplied
● through BCM terminal 51
● to trailer turn relay RH terminal 1
When energized, trailer turn relay RH supplies power to the right stop, turn signal, and hazard lamp
● through trailer turn relay RH terminal 3
● to trailer connector terminal 5 (trailer tow 7 pin) or terminal 2 (trailer tow 4 pin).
TRAILER POWER SUPPLY OPERATION
The trailer power supply (trailer tow 7 pin connector only) is controlled by trailer tow relay 2.
When the ignition switch is in the ON or START position, power is supplied
● through 10A fuse (No. 38, located in the IPDM E/R)
● through IPDM E/R terminal 27

Revision: September 2005 LT-107 2006 Pathfinder


TRAILER TOW

● to trailer tow relay 2 terminal 1.


When energized, trailer tow relay 2 power is supplied
● through trailer tow relay 2 terminals 5 and 7
● to trailer connector terminal 4.

Revision: September 2005 LT-108 2006 Pathfinder


TRAILER TOW

Schematic EKS00FX6

LT

WKWA4232E

Revision: September 2005 LT-109 2006 Pathfinder


TRAILER TOW

Wiring Diagram — T/TOW — EKS00FX7

WKWA4233E

Revision: September 2005 LT-110 2006 Pathfinder


TRAILER TOW

LT

WKWA4234E

Revision: September 2005 LT-111 2006 Pathfinder


TRAILER TOW

WKWA4235E

Revision: September 2005 LT-112 2006 Pathfinder


TRAILER TOW

LT

WKWA4236E

Revision: September 2005 LT-113 2006 Pathfinder


TRAILER TOW

WKWA4237E

Revision: September 2005 LT-114 2006 Pathfinder


INTERIOR ROOM LAMP

INTERIOR ROOM LAMP PFP:26410


A
Component Parts and Harness Connector Location EKS00FX8

LT

WKIA4971E
M
1. BCM 2. Key switch 3. Steering column assembly
M18, M19, M20 M27
(view with instrument lower panel (view with instrument lower panel LH
LH removed) removed)
4. Glass hatch ajar switch 5. Front door switch LH 6. Rear door switch LH
D506 B8 B18
Front door switch RH Rear door switch RH
B108 B116
7. Back door switch 8. Room lamp 2nd row 9. Front room/map lamp assembly
D502 (without map lamps) (with front map lamps)
R12 R9
(with rear map lamps)
R10
10. Vanity lamps (with vanity lamps) 11. Ignition keyhole illumination 12. Cargo lamp
LH B80 M150 R11
Vanity lamps
RH B81

Revision: September 2005 LT-115 2006 Pathfinder


INTERIOR ROOM LAMP

System Description EKS00FX9

When room lamp and personal lamp switch is in DOOR position, room lamp and personal lamp ON/OFF is
controlled by timer according to signals from switches including key switch, front door switch LH, unlock signal
from keyfob, door lock and unlock switch, key cylinder switch, ignition switch and glass hatch ajar switch.
When room/map lamp and personal lamp turns ON, there is a gradual brightening over 1 second. When room/
map lamp and personal lamp turns OFF, there is a gradual dimming over 1 second.
The room/map lamp and personal lamp timer is controlled by the BCM (body control module).
Room/map lamp and personal lamp timer control settings can be changed with CONSULT-II.
Ignition keyhole illumination turns ON when front door LH is opened (door switch ON) or key is removed from
key cylinder. Illumination turns OFF when front door LH is closed (door switch OFF).
POWER SUPPLY AND GROUND
Power is supplied at all times
● through 10A fuse (No. 25, located in the fuse and fusible link box)
● to key switch terminal 2, and
● through 10A fuse [No. 18, located in the fuse block (J/B)]
● to BCM terminal 57, and
● through 50A fusible link (letter g , located in the fuse and fusible link box)
● to BCM terminal 70.
When the key is inserted in key switch, power is supplied
● through the key switch terminal 1
● to BCM terminal 37.
With the ignition switch in the ON or START position, power is supplied
● through 10A fuse [No. 1, located in the fuse block (J/B)]
● to BCM terminal 38.
Ground is supplied
● to BCM terminal 67
● through grounds M57, M61 and M79.
When the front door LH is opened, ground is supplied
● to BCM terminal 47
● through front door switch LH terminal 2
● through case ground of front door switch LH.
When the front door RH is opened, ground is supplied
● to BCM terminal 12
● through front door switch RH terminal 2
● through case ground of front door switch RH.
When the rear door LH is opened, ground is supplied
● to BCM terminal 48
● through rear door switch LH terminal 2
● through case ground of rear door switch LH.
When the rear door RH is opened, ground is supplied
● to BCM terminal 13
● through rear door switch RH terminal 2
● through case ground of rear door switch RH.
When the glass hatch is opened, ground is supplied
● to BCM terminal 42
● through glass hatch ajar switch terminal 1
● through case ground of glass hatch ajar switch.
When the liftgate is opened, ground is supplied
● to BCM terminal 43
● through back door switch terminal 3

Revision: September 2005 LT-116 2006 Pathfinder


INTERIOR ROOM LAMP

● through back door switch terminal 1


● through grounds D406 and D504. A
When the front door LH or RH is unlocked by the door lock and unlock switch, BCM receives ground signal
● to BCM terminal 46
B
● through main power window and door lock/unlock switch terminal 11 or power window and door lock/
unlock switch RH terminal 2
● through main power window and door lock/unlock switch terminal 14 or power window and door lock/
unlock switch RH terminal 3 C
● through grounds M57, M61 and M79.
When the front door LH is unlocked by the key, the BCM receives ground signal
D
● to BCM terminal 7
● through front door lock assembly LH (key cylinder switch) terminal 3
● through front door lock assembly LH (key cylinder switch) terminal 4 E
● through grounds M57, M61 and M79.
When a signal, or combination of signals is received by BCM, ground is supplied
● to front room/map lamp assembly terminal 2 F
● to personal lamp 2nd row terminal 2 (with rear map lamps)
● to room lamp 2nd row terminal 1
● through BCM terminal 63, and G
● to cargo lamp terminal 1
● through BCM terminal 49.
H
With power and ground supplied, the lamps illuminate.
SWITCH OPERATION
When any door switch is ON (door is opened), ground is supplied I
● to front room/map lamp assembly terminal 2
● to personal lamp 2nd row terminal 2 (with rear map lamps)
J
● to room lamp 2nd row terminal 1
● through BCM terminal 63, and
● to ignition keyhole illumination terminal 2
LT
● through BCM terminal 1.
And power is supplied
● through BCM terminal 56 L
● to ignition keyhole illumination terminal 1
● to front room/map lamp assembly terminal 1
● to vanity lamp LH and RH terminal 1 (if equipped) M
● to personal lamp 2nd row terminal 1 (with rear map lamps)
● to room lamp 2nd row terminal 2
● to cargo lamp terminal 2.
When front room/map lamp switch is ON, ground is supplied
● to front room/map lamp assembly terminal 3
● through grounds M57, M61 and M79.
When vanity lamp (LH and RH) (if equipped) is ON, ground is supplied
● to vanity lamp (LH and RH) terminal 2
● through grounds B7 and B19.
When personal lamp 2nd row (with rear map lamps) is ON, ground is supplied
● to personal lamp 2nd row terminal 3
● through grounds M57, M61 and M79.
When room lamp 2nd row is ON, ground is supplied through room lamp case ground.
When cargo lamp switch is ON, ground is supplied through cargo lamp case ground.

Revision: September 2005 LT-117 2006 Pathfinder


INTERIOR ROOM LAMP

ROOM LAMP TIMER OPERATION


When lamp switch is in DOOR position, and when all conditions below are met, BCM performs timer control
(maximum 30 seconds) for interior room lamp and map lamp ON/OFF.
Power is supplied
● through 10A fuse [No. 25, located in the fuse block (J/B)]
● to key switch terminal 2.
Key is removed from ignition key cylinder (key switch OFF), power will not be supplied to BCM terminal 37.
Ground is supplied
● to BCM terminal 46
● through main power window and door lock/unlock switch terminal 11.
At the time that front door LH is opened, BCM detects that front door LH is unlocked. It determines that interior
room lamp and map lamp timer operation conditions are met, and turns the interior room lamps ON for 30 sec-
onds.
Key is in ignition key cylinder (key switch ON), power is supplied
● through key switch terminal 1
● to BCM terminal 37.
When key is removed from key switch and key lock solenoid (key switch OFF), power supply to BCM terminal
37 is terminated. BCM detects that key has been removed, determines that interior room lamp and map lamp
timer conditions are met, and turns the interior room lamps ON for 30 seconds.
When front door LH opens → closes, and the key is not inserted in the key switch (key switch OFF), BCM ter-
minal 47 changes between 0V (door open) → 12V (door closed). The BCM determines that conditions for inte-
rior room lamp operation are met and turns the interior room lamp ON for 30 seconds.
Timer control is canceled under the following conditions.
● Front door LH is locked [when locked by keyfob, main power window and door lock/unlock switch, or front
door lock assembly LH (key cylinder switch)]
● Front door LH is opened (front door switch LH turns ON)
● Ignition switch ON.
INTERIOR LAMP BATTERY SAVER CONTROL
If interior lamp is left ON, it will not be turned off even when door is closed.
BCM turns off interior lamp automatically to save battery 30 minutes after ignition switch is turned off.
BCM controls interior lamps listed below:
● Vanity lamp (if equipped)
● Front room/map lamp
● Cargo lamp
● Personal lamp 2nd row (with rear map lamps)
● Room lamp 2nd row
● Ignition keyhole illumination
After lamps turn OFF by the battery saver system, the lamps illuminate again when
● signal received from keyfob, main power window and door lock/unlock switch or front door lock assembly
LH (key cylinder switch) is locked or unlocked
● door is opened or closed
● key is removed from ignition key cylinder or inserted in ignition key cylinder.
Interior lamp battery saver control period can be changed by the function setting of CONSULT-II.

Revision: September 2005 LT-118 2006 Pathfinder


INTERIOR ROOM LAMP

Schematic EKS00FXA

LT

WKWA4309E

Revision: September 2005 LT-119 2006 Pathfinder


INTERIOR ROOM LAMP

WKWA3092E

Revision: September 2005 LT-120 2006 Pathfinder


INTERIOR ROOM LAMP

Wiring Diagram — INT/L — EKS00FXB

LT

WKWA4238E

Revision: September 2005 LT-121 2006 Pathfinder


INTERIOR ROOM LAMP

WKWA4343E

Revision: September 2005 LT-122 2006 Pathfinder


INTERIOR ROOM LAMP

LT

WKWA2070E

Revision: September 2005 LT-123 2006 Pathfinder


INTERIOR ROOM LAMP

WKWA4239E

Revision: September 2005 LT-124 2006 Pathfinder


INTERIOR ROOM LAMP

LT

WKWA3094E

Revision: September 2005 LT-125 2006 Pathfinder


INTERIOR ROOM LAMP

Terminals and Reference Values for BCM EKS00FXC

Refer to BCS-12, "Terminals and Reference Values for BCM" .


How to Proceed With Trouble Diagnosis EKS00FXD

1. Confirm the symptom or customer complaint.


2. Understand operation description and function description. Refer to LT-116, "System Description" .
3. Carry out the Preliminary Check. Refer to LT-126, "Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does the interior room lamp operate normally? If YES: GO TO 6. If NO: GO TO 4.
6. Inspection End.
Preliminary Check EKS00FXE

INSPECTION FOR POWER SUPPLY AND GROUND CIRCUIT


Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" .
CONSULT-II Function (BCM) EKS00FXF

CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
BCM diagnostic
Diagnostic mode Description
test item
Supports inspections and adjustments. Commands are transmitted to the BCM
WORK SUPPORT for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
Inspection by part
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.

CONSULT-II OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, then turn igni-
tion switch ON.

BBIA0538E

Revision: September 2005 LT-126 2006 Pathfinder


INTERIOR ROOM LAMP

2. Touch "START (NISSAN BASED VHCL)".


A

BCIA0029E

D
3. Touch "BCM" on "SELECT SYSTEM" screen.
If "BCM" is not indicated, go to GI-40, "CONSULT-II Data Link
Connector (DLC) Circuit" .
E

G
BCIA0030E

4. Touch "INT LAMP" on "SELECT TEST ITEM" screen.


H

PKIA5226E
LT

WORK SUPPORT
Operation Procedure L
1. Touch "INT LAMP" on "SELECT TEST ITEM" screen.
2. Touch "WORK SUPPORT" on "SELECT DIAG MODE" screen.
3. Touch "SET I/L D-UNLCK INTCON" on "SELECT WORK ITEM" screen. M
4. Touch "START".
5. Touch "CHANGE SETT".
6. The setting will be changed and "CUSTOMIZING COMPLETED" will be displayed.
7. Touch "END".
Display Item List
Item Description CONSULT-II
The 30 seconds operating function of the interior room lamps and the
SET I/L D-UNLCK INTCON ignition keyhole illumination can be selected when front door LH is ON/OFF
released (unlocked).
The time in order to escalate illumination can be adjusted when the
ROOM LAMP ON TIME SET MODE 1 - 7
interior room lamps and the ignition keyhole illumination is turned on.
The time in order to diminish illumination can be adjusted when the
ROOM LAMP OFF TIME SET MODE 1 - 7
interior room lamps and the ignition keyhole illumination is turned off.

Reference between "MODE" and "TIME" for "TURN ON/OFF".

Revision: September 2005 LT-127 2006 Pathfinder


INTERIOR ROOM LAMP

MODE 1 2 3 4 5 6 7
Time (sec.) 0.5 1 2 3 4 5 0

DATA MONITOR
Operation Procedure
1. Touch "INT LAMP" on "SELECT TEST ITEM" screen.
2. Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
3. Touch either "ALL SIGNALS" or "SELECTION FROM MENU" on "SELECT MONITOR ITEM" screen.

ALL SIGNALS Monitors all the signals.


SELECTION FROM MENU Selects and monitors the individual signal.

4. Touch "START".
5. When "SELECTION FROM MENU" is selected, touch items to be monitored. When "ALL SIGNALS" is
selected, all the items will be monitored.
6. Touch "RECORD" while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch "STOP".
Display Item List
Monitor item Contents
Displays "IGN position (ON)/OFF, ACC position (OFF)" judged from the ignition switch
IGN ON SW "ON/OFF"
signal.
Displays "Key inserted (ON)/key removed (OFF)" status judged from the key switch
KEY ON SW "ON/OFF"
signal.
Displays status of the front door LH as judged from the front door switch LH signal.
DOOR SW-DR "ON/OFF"
(Door is open: ON/Door is closed: OFF)
Displays "Door open (ON)/Door closed (OFF)" status, determined from front door
DOOR SW-AS "ON/OFF"
switch RH signal.
Displays "Door open (ON)/Door closed (OFF)" status, determined from rear door
DOOR SW-RR "ON/OFF"
switch RH signal.
Displays "Door open (ON)/Door closed (OFF)" status, determined from rear door
DOOR SW-RL "ON/OFF"
switch LH signal.
Displays "Door open (ON)/Door closed (OFF)" status, determined from back door
BACK DOOR SW "ON/OFF"
switch signal.
Displays "Door locked (ON)" status, determined from key cylinder lock switch in front
KEY CYL LK-SW "ON/OFF"
door LH.
Displays "Door unlocked (OFF)" status, determined from key cylinder lock switch in
KEY CYL UN-SW "ON/OFF"
front door LH.
Displays "Door locked (ON)/Door unlocked (OFF)" status, determined from locking
CDL LOCK SW "ON/OFF"
detection switch in front door LH.
Displays "Door unlocked (OFF)" status, determined from locking detection switch in
CDL UNLOCK SW "ON/OFF"
front door RH.
KEYLESS LOCK "ON/OFF" Displays "Locked (ON)/Other (OFF)" status, determined from lock signal.
KEYLESS UNLOCK "ON/OFF" Displays "Unlocked (ON)/Other (OFF)" status, determined from unlock signal.

ACTIVE TEST
Operation Procedure
1. Touch "INT LAMP" on "SELECT TEST ITEM" screen.
2. Touch "ACTIVE TEST" on "SELECT DIAG MODE" screen.
3. Touch item to be tested and check operation of the selected item.
4. During the operation check, touching "BACK" or "OFF" deactivates the operation.

Revision: September 2005 LT-128 2006 Pathfinder


INTERIOR ROOM LAMP

Display Item List


Test item Description
A

INT LAMP Interior room lamp can be operated by any ON-OFF operations.
IGN ILLUM Ignition keyhole illumination can be operated by ON-OFF operation. B
Room/Map Lamp Control Does Not Operate EKS00FXG

1. CHECK EACH SWITCH C


Select "BCM" on CONSULT-II. With "INT LAMP" data monitor, make
sure switches listed in display item list turn ON-OFF linked with
switch operation. Refer to LT-128, "Display Item List" for switches D
and their functions.
OK or NG
OK >> GO TO 2. E
NG >> Inspect malfunctioning switch system.

F
SKIA5930E

2. ACTIVE TEST G

1. Select "BCM" on CONSULT-II. Select "INT LAMP" active test.


2. When switch is in DOOR position, use active test to make sure H
interior room lamp operates.
Room lamps should turn on.
OK or NG I
OK >> Replace BCM. Refer to BCS-27, "Removal and Installa-
tion" .
NG >> GO TO 3. J

LKIA0092E

3. CHECK INTERIOR ROOM LAMP INPUT LT

1. Turn ignition switch OFF.


2. Check voltage between front room/map lamp assembly harness L
connector R9 terminal 1 and ground.
1 - Ground : Battery voltage should exist.
M
OK or NG
OK >> GO TO 4.
NG >> GO TO 5.

WKIA3323E

Revision: September 2005 LT-129 2006 Pathfinder


INTERIOR ROOM LAMP

4. CHECK INTERIOR ROOM LAMP CIRCUIT


1. Disconnect BCM connector.
2. Check continuity between BCM harness connector M20 terminal
63 and front room/map lamp assembly harness connector R9
terminal 2.
63 - 2 : Continuity should exist.
OK or NG
OK >> Replace BCM if interior lamp does not work after setting
the connector again. Refer to BCS-27, "Removal and
Installation" .
NG >> Repair harness or connector. WKIA3324E

5. CHECK INTERIOR ROOM LAMP CIRCUIT


1. Disconnect BCM connector and front room/map lamp assembly
connector.
2. Check continuity between BCM harness connector M20 terminal
56 and front room/map lamp assembly harness connector R9
terminal 1.
56 - 1 : Continuity should exist.
OK or NG
OK >> Replace BCM if interior lamp does not work after setting
the connector again. Refer to BCS-27, "Removal and
Installation" . WKIA3325E

NG >> Repair harness or connector between BCM and room/


map lamp.

Revision: September 2005 LT-130 2006 Pathfinder


INTERIOR ROOM LAMP

Personal Lamp Control Does Not Operate (Room/Map Lamps Operate) EKS00FXH

1. CHECK EACH DOOR SWITCH A

Select "BCM" on CONSULT-II. With "INT LAMP" data monitor, make


sure switches listed in display item list turn ON-OFF linked with B
switch operation. Refer to LT-117, "SWITCH OPERATION" for
switches and their function.
OK or NG C
OK >> GO TO 2.
NG >> Inspect malfunctioning door switch.
D

SKIA5930E

E
2. CHECK PERSONAL LAMP OUTPUT
1. Turn ignition switch OFF.
F
2. Confirm lamp switch is in the DOOR position.
3. Disconnect personal lamp 2nd row connector.
4. Open any door. G
5. Check voltage between personal lamp 2nd row harness connec-
tor R10 terminal 1 and ground.
1 - Ground : Battery voltage should exist. H
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector. I

J
WKIA3326E

3. CHECK PERSONAL LAMP CONTROL CIRCUIT LT


1. Disconnect front room/map lamp assembly connector.
2. Check continuity between front room/map lamp assembly har-
ness connector R9 terminal 3 and personal lamp 2nd row har- L
ness connector R10 terminal 3.
3-3 : Continuity should exist.
M
OK or NG
OK >> Replace personal lamp 2nd row.
NG >> Repair harness or connector.
WKIA3327E

Revision: September 2005 LT-131 2006 Pathfinder


INTERIOR ROOM LAMP

All Interior Room Lamps Do Not Operate EKS00FXI

1. CHECK POWER SUPPLY CIRCUIT


1. All interior room lamp switches are OFF.
2. Turn ignition switch ON.
3. Check voltage between BCM harness connector M20 terminal
56 and ground.
56 - Ground : Battery voltage should exist.
OK or NG
OK >> Repair harness or connector. To prevent making a short
circuit, be sure to disconnect battery negative cable
after repairing harness, and then reconnect.
WKIA1486E
NG >> Replace BCM. Refer to BCS-27, "Removal and Installa-
tion" .
Ignition Keyhole Illumination Control Does Not Operate EKS00FXJ

1. CHECK EACH SWITCH


Select “BCM” on CONSULT-II. With “INT LAMP” data monitor, make
sure switches listed in display item list turn ON-OFF linked with
switch operation. Refer to LT-128, "Display Item List" for switches
and their functions.
OK or NG
OK >> GO TO 2.
NG >> Inspect malfunctioning switch system.

SKIA5930E

2. ACTIVE TEST
1. Select “BCM” on CONSULT-II. Select “INT LAMP”.
2. Select “IGN ILLUM” active test to make sure lamp operates.
OK or NG
OK >> Replace BCM. Refer to BCS-27, "Removal and Installa-
tion" .
NG >> GO TO 3.

SKIA3992E

Revision: September 2005 LT-132 2006 Pathfinder


INTERIOR ROOM LAMP

3. CHECK IGNITION KEYHOLE ILLUMINATION POWER SUPPLY INPUT A


1. Check voltage between ignition keyhole illumination harness
connector M150 terminal 1 and ground.
B
Terminals
(+)
Voltage
(–)
Ignition keyhole (Approx.) C
illumination Terminal
connector
M150 1 Ground Battery voltage
D
OK or NG WKIA4157E
OK >> GO TO 4.
NG >> GO TO 6. E

4. CHECK IGNITION KEYHOLE ILLUMINATION BULB


1. Turn ignition switch OFF. F
2. Disconnect ignition keyhole illumination connector.
3. Check continuity between ignition keyhole illumination terminals
1 and 2. G

Terminals
Ignition keyhole illumination Continuity H
terminal
1 2 Yes
OK or NG I
OK >> GO TO 5. WKIA4463E

NG >> Replace ignition keyhole illumination bulb.


J
5. CHECK IGNITION KEYHOLE ILLUMINATION CONTROL CIRCUIT
1. Disconnect BCM connector. LT
2. Check continuity between BCM harness connector M18 (A) ter-
minal 1 and ignition keyhole illumination harness connector
M150 (B) terminal 2.
L
A B
Ignition
BCM keyhole Continuity M
Terminal Terminal
connector illumination
connector
M18 1 M150 2 Yes WKIA4010E

OK or NG
OK >> Replace BCM if ignition keyhole illumination does not work after setting the connector again.
Refer to BCS-27, "Removal and Installation" .
NG >> Repair harness or connector.

Revision: September 2005 LT-133 2006 Pathfinder


INTERIOR ROOM LAMP

6. CHECK IGNITION KEYHOLE ILLUMINATION POWER SUPPLY CIRCUIT


1. Turn ignition switch OFF.
2. Disconnect BCM connector and ignition keyhole illumination
connector.
3. Check continuity between BCM harness connector M20 (A) ter-
minal 56 and ignition keyhole illumination harness connector
M150 (B) terminal 1.
A B
Ignition
BCM keyhole Continuity
Terminal Terminal
connector illumination WKIA4011E

connector
M20 56 M150 1 Yes
OK or NG
OK >> Replace BCM if ignition keyhole illumination does not work after setting the connector again.
Refer to BCS-27, "Removal and Installation" .
NG >> Repair harness or connector.

Revision: September 2005 LT-134 2006 Pathfinder


ILLUMINATION

ILLUMINATION PFP:27545
A
Component Parts and Harness Connector Location EKS00FXK

WKIA4973E

1. IPDM E/R 2. Combination switch (lighting switch) 3. Combination meter J


E118, E119, E120, E121, E122, M28 M24
E123, E124
4. Illumination control switch 5. BCM
LT
(built into combination meter) M18, M19, M20
(view with instrument lower panel LH removed)

System Description EKS00FXL L


Control of the illumination lamps operation is dependent upon the position of the lighting switch (combination
switch). When the lighting switch is placed in the 1ST or 2ND position (or if the auto light system is activated)
the BCM (body control module) receives input signal requesting the illumination lamps to illuminate. This input M
signal is communicated to the IPDM E/R (intelligent power distribution module engine room) across the CAN
communication lines. The CPU (central processing unit) of the IPDM E/R controls the tail lamp relay coil. This
relay, when energized, directs power to the illumination lamps, which then illuminate.
Power is supplied at all times
● to ignition relay, located in the IPDM E/R, and
● to tail lamp relay, located in the IPDM E/R, and
● through 50A fusible link (letter g , located in the fuse and fusible link box)
● to BCM terminal 70, and
● through 20A fuse (No. 53, located in the IPDM E/R)
● to CPU of the IPDM E/R, and
● through 10A fuse [No.19, located in fuse block (J/B)]
● to combination meter terminal 3.
With the ignition switch in the ON or START position, power is supplied
● to ignition relay, located in the IPDM E/R, and
● through 10A fuse [No. 1, located in the fuse block (J/B)]

Revision: September 2005 LT-135 2006 Pathfinder


ILLUMINATION

● to BCM terminal 38.


Ground is supplied
● to BCM terminal 67 and
● to combination meter terminals 13 and 23
● through grounds M57, M61 and M79, and
● to IPDM E/R terminals 38 and 59
● through grounds E9, E15 and E24.
ILLUMINATION OPERATION BY LIGHTING SWITCH
With the lighting switch in the 1ST or 2ND position (or if the auto light system is activated), the BCM receives
input signal requesting the illumination lamps to illuminate. This input signal is communicated to the IPDM E/R
across the CAN communication lines. The CPU of the IPDM E/R controls the tail lamp relay coil, which, when
energized, directs power
● through 10A fuse (No. 37, located in the IPDM E/R)
● through IPDM E/R terminal 57
● to AV switch terminal 3 (with NAVI)
● to hazard switch terminal 3
● to audio unit terminal 8
● to glove box lamp terminal 1
● to display control unit terminal 14 (with NAVI)
● to 4WD shift switch terminal 7 (with 4-wheel drive)
● to front air control terminal 8
● to DVD player terminal 12 (with DVD entertainment system)
● to NAVI control unit terminal 61 (with NAVI)
● to rear air control terminal 1 (with auto A/C)
● to pedal adjusting switch terminal 5 (with adjustable pedals)
● to door mirror remote control switch terminal 16
● to electric brake (pre-wiring) terminal 4 (with trailer tow 7 pin)
● to A/T device terminal 3
● to front heated seat switch LH and RH terminal 5 (with heated seats)
● to VDC OFF switch terminal 3 and
● to HDC switch terminal 5 (with hill descent control and hill start assist).
Illumination is controlled
● through combination meter terminal 22
● to AV switch terminal 4 (with NAVI)
● to hazard switch terminal 4
● to audio unit terminal 7
● to 4WD switch terminal 8 (with 4-wheel drive)
● to front air control terminal 9
● to DVD player terminal 10 (with DVD entertainment system)
● to pedal adjusting switch terminal 6 (with adjustable pedals)
● to door mirror remote control switch terminal 15
● to A/T device terminal 5
● to front heated seat switch LH and RH terminal 6 (with heated seats)
● to VDC OFF switch terminal 4 and
● to HDC switch terminal 6 (with hill descent control and hill start assist).
Ground is supplied
● to glove box lamp terminal 2
● to display control unit terminal 3 (with NAVI)
● to electric brake (pre-wiring) terminal 1 (with trailer tow 7 pin) and

Revision: September 2005 LT-136 2006 Pathfinder


ILLUMINATION

● to rear air control terminal 3 (with auto A/C)


● through grounds M57, M61 and M79, and A
● to NAVI control unit terminal 1 (with NAVI)
● through grounds B117 and B132.
B
With power and ground supplied, illumination lamps illuminate.
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 1ST or 2ND position (or if auto light system is acti- C
vated), and the ignition switch is turned from ON or ACC to OFF, the battery saver control function is activated.
Under this condition, the illumination lamps remain illuminated for 5 minutes, then the illumination lamps are
turned off.
D
When the lighting switch is turned from OFF to 1ST or 2ND position (or if auto light system is activated) after
illumination lamps are turned off by the battery saver control, the illumination lamps illuminate again.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-II.
E
CAN Communication System Description EKS00FXM

Refer to LAN-25, "CAN COMMUNICATION" .


F

LT

Revision: September 2005 LT-137 2006 Pathfinder


ILLUMINATION

Schematic EKS00FXN

WKWA4240E

Revision: September 2005 LT-138 2006 Pathfinder


ILLUMINATION

LT

WKWA2074E

Revision: September 2005 LT-139 2006 Pathfinder


ILLUMINATION

WKWA4241E

Revision: September 2005 LT-140 2006 Pathfinder


ILLUMINATION

Wiring Diagram — ILL — EKS00FXO

LT

WKWA4242E

Revision: September 2005 LT-141 2006 Pathfinder


ILLUMINATION

WKWA2077E

Revision: September 2005 LT-142 2006 Pathfinder


ILLUMINATION

LT

WKWA4243E

Revision: September 2005 LT-143 2006 Pathfinder


ILLUMINATION

WKWA2079E

Revision: September 2005 LT-144 2006 Pathfinder


ILLUMINATION

LT

WKWA2080E

Revision: September 2005 LT-145 2006 Pathfinder


ILLUMINATION

WKWA4244E

Revision: September 2005 LT-146 2006 Pathfinder


ILLUMINATION

LT

WKWA4389E

Revision: September 2005 LT-147 2006 Pathfinder


ILLUMINATION

WKWA4245E

Revision: September 2005 LT-148 2006 Pathfinder


ILLUMINATION

LT

WKWA4246E

Revision: September 2005 LT-149 2006 Pathfinder


ILLUMINATION

Removal and Installation EKS00FXP

ILLUMINATION CONTROL SWITCH


The illumination control switch is a function of the combination meter,
and not serviced separately. For replacement, refer to IP-14, "COM-
BINATION METER"

LKIA0579E

Revision: September 2005 LT-150 2006 Pathfinder


BULB SPECIFICATIONS

BULB SPECIFICATIONS PFP:26297


A
Headlamp EKS00FXQ

Item Wattage (W)*


Low/High 65/55 (HB5) B
*: Always check with the Parts Department for the latest parts information.

Exterior Lamp EKS00FXR C


Item Wattage (W)*
Turn signal lamp/parking lamp 28/8
Front combination lamp D
Side marker 3.8
Stop/Tail lamp 27/8
Rear combination lamp Turn signal lamp 27 E
Back-up lamp 18
Front fog lamp 55
F
License plate lamp 5
High-mounted stop lamp *
*: Always check with the Parts Department for the latest parts information. G
Interior Lamp/Illumination EKS00FXS

Item Wattage (W)* H


Glove box lamp 3.4
Room/Map lamp 8
I
A/T device lamp 3
Cargo lamp 8
Vanity lamp * J
Personal lamp 8
*: Always check with the Parts Department for the latest parts information.
LT

Revision: September 2005 LT-151 2006 Pathfinder


BULB SPECIFICATIONS

Revision: September 2005 LT-152 2006 Pathfinder

You might also like