CONTENTS

BEFORE USING THE WASHING MACHINE

PRECAUTIONS AND GENERAL
RECOMMENDATIONS
INSTALLATION
DESCRIPTION OF THE WASHING MACHINE
DOOR
BEFORE THE FIRST WASH CYCLE
PREPARATION OF THE WASHING
DETERGENTS AND ADDITIVES
REMOVING THE FILTER/DRAINING
RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
ACCESSORIES
BUILT-IN MODELS

BEFORE USING THE WASHING MACHINE

Please, read these instructions carefully before connecting and using the appliance.
Before connecting the appliance read these instructions carefully. Repairing the
failure arising from inappropriate connections or use of the appliance is not
covered by the guarantee.

1.Removing the packaging and inspection

After unpacking, make sure that the washing
machine is undamaged. If in doubt, do not use the
washing machine. Contact After-Sales Service or
your local retailer.
Check that the accessories and supplied parts are
all present.
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children,
as they are potentially dangerous.
If the appliance was exposed to the cold before
delivery, keep it at room temperature for a few
hours before operating.

Water tap:

Cold water only (unless

otherwise indicated on
the programme chart)
3/4 threaded hose
connector

Water pressure
(flow pressure):
100-1000 kPa (1-10 bar).
Use only new hoses to connect the washing
machine to the water supply. Used hoses must
not be used and should be discarded,

5.Drain

Connect the drain hose to the siphon or hook it

over the edge of a sink by means of the U bend
supplied.
If the washing machine is connected to an
integrated drainage system, ensure the latter is
equipped with a vent to avoid simultaneous
loading and draining of water (siphoning effect).

2.Remove the transport bolts

The washing machine is fitted with transport

bolts to avoid any possible damage to the interior
during transport. Before using the washing
machine, it is imperative that the transport bolts
are removed.
After their removal, cover the openings with the
4 enclosed plastic caps.

3.Install the washing machine

Water supply:

6.Electrical connections

You are advised not to install the appliance in a

room where the temperature could drop to
below 0C.
Given the weight of the appliance, attention must
be paid to safety standards when it is being moved.
When positioning the appliance, make sure that
the power cable is not kinked or compressed and
that it can be easily accessed if required.
Remove the protective film from the control
panel (if available on your model).
Move the appliance without carrying it by the
worktop.
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
Make sure that all four feet are stable and resting
on the floor and then check that the washing
machine is perfectly level (use a spirit level).
In case of wooden or so-called floating floors
(for instance certain parquet or laminate floors),
place the appliance on a 60 x 60 cm sheet of
plywood at least 3 cm in thickness which is
secured to the floor.
If the washing machine is installed on a carpeted
floor, leave sufficient space between the
appliance and the floor to guarantee the free
circulation of air.

Electrical connections must be carried out by a

qualified technician in compliance with the
manufacturers instructions and current standard
safety regulations.
Voltage, power consumption and electrical
protection data are supplied on the inside of the
appliance door.
The washing machine must be connected
exclusively by means of a socket with an earth
connection in accordance with current
regulations. The washing machine must be
earthed by law. The manufacturer declines all
liability for possible damage to property or injury
to persons or pets deriving from failure to
observe the a/m directions.
Do not use extension leads or multi sockets.
Before any maintenance on the washing machine
disconnect it from the mains supply.
After installation, access to the mains plug or to
disconnection from mains supply must be
ensured at all times via a double-pole switch.
Do not operate the washing machine if it has
been damaged during transport. Inform the
After-Sales Service.
Mains cable replacement is only to be carried out
by After-Sales Service.
Use the appliance only for domestic washing and
for its intended applications.

Minimum housing dimensions:

Width:
Height:
Depth:

4.Water supply

Connect the water supply inlet hose in

accordance with the regulations of your local
water company.
GB 2

600 mm
850 mm
600 mm

PRECAUTIONS AND GENERAL

RECOMMENDATIONS
1.Packing

If necessary, the power cable may be replaced

with an identical one obtained from our AfterSales Service. The power cable must only be
replaced by a qualified technician.
Lighters must not be left in pockets.
For washer/dryer models
Do NOT dry items that have been washed or
treated with chemical stain removers, cooking
oil, petroleum, acetone, alcohol, petrol, paraffin,
white spirit, wax.
Remove these substances by means of a hot wash
with abundant detergent before drying.
Do NOT dry items made from foam rubber,
latex, raincoats, waterproof fabrics, rubber
airbeds, printed objects, clothes or pillows filled
with foam rubber. These materials could melt
and damage other items in the wash or damage
the appliance.
The use and quantities of detergent, softener and
bleach must comply with the instructions
reported on the packaging.
Never dry unwashed items.
WARNING!!! The final part of a drying cycle is
the cooling down phase. Consequently, never
switch off the dryer before the cycle has been
completed. Otherwise, the washing must be
taken out quickly and hung out to allow the heat
to dissipate.

The packaging material is entirely recyclable, and

marked with the recycling symbol
. Adhere
to local regulations when disposing of packaging
material.

2.Disposing of packaging and scrapping

old washing machines

The appliance is built from reusable materials. It

must be disposed of in compliance with current
local waste disposal regulations.
Before scrapping, remove all detergent residues
and cut off the power cable so that the washing
machine is made unusable.
This appliance is marked according to European
Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
By ensuring that this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment and
human health.
The symbol
on the product, or on the
documents accompanying the product, indicates
that this appliance may not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling
of electrical and electronic equipment.
Disposal must be carried out in accordance with
local environmental regulations for waste disposal.
For more detailed information about treatment,
recovery and recycling of this product, please
contact your local city office, your household
waste disposal service or the shop where you
purchased the product.

3.Safety Instructions

4.Advice on saving energy

The washing machine can only be used indoors.

Do not store flammable fluids near the appliance.
If you want to place a dryer on top of your
washing machine, first contact our After-Sales
Service or your specialist dealer to verify if this is
possible. Placing a dryer on your washing
machine is only admitted by using an appropriate
stacking kit available through our After-Sales
Service or your specialist dealer.
Do not leave the appliance plugged in when not
in use.
Turn off the tap when not in use.
Before any cleaning and maintenance switch off
the machine or disconnect it from the mains.
Never open the door forcibly or use it as a step.
Children must not be allowed to play with the
washing machine or to climb into the drum.
This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.

To achieve the best use of energy, water,

detergent and time use the recommended
maximum load size.
Do not exceed the recommended dosages on
the detergent packet.
The Eco Flap - a special system in the outlet prevents detergent loss from the drum to avoid
detergent loss into the environment.
Use the Pre-wash programme for heavily soiled
laundry only. Use a programme with no Prewash cycle for slightly or normally soiled items;
You save on water, energy and time as a result.
Before using the washing machine, treat laundry
with a stain remover or soak dry stained items in
water so as to avoid having to use high
temperature wash programmes.
Save energy by using a 60 C instead of a 95 C
wash programme or a 40 C instead of a 60 C
wash programme.
Save energy and time by selecting a high spin
speed to reduce the water content in laundry
before using a drying programme (for machines
with adjustable spin speed).

5.EC Declaration of Conformity

The appliance conforms to the following

European Standards:
73/23/EEC Low voltage directive
89/336/EEC EMC Directive
93/68/EC CE Marking Directive
.

GB 3

INSTALLATION
WARNING!!! The washer/dryer version must not be installed behind a
locked door, a sliding door or with a hinged door on the opposite wall to
the washer/dryer itself.
Remove the transport bolts
1. Loosen the three or four bolts (A).

2. Unscrew the bolts by hand.

3. Take hold of the bolts and plastic spacers and
remove them. Keep the transport safety bolts for
possible future use.
4. Close the holes with the plastic covers (supplied
with the documents).

TRANSPORT/HANDLING
Never lift the appliance by the worktop when transporting.
1. Unplug the appliance.
2. Shut off the water tap.
3. Check that the door and detergent dispenser are properly closed.
4. Remove the water supply and drain hose from the domestic connection.
5. Remove any water remaining in the hoses and the appliance (see Removing The Filter/Draining
Residual Water).
6. Pry off the plastic covers with a screwdriver and remove them.
7. Insert the transit screws following the removal procedure in reverse.

GB 4

DESCRIPTION OF THE WASHING MACHINE

1

2
3

2
3
4

6
6
7

1.
2.
3.
4.
5.
6.
7.

Worktop
Control panel
Detergent drawer
After-Sales Service sticker (inside door)
Door
Pump access behind plinth or cover (depending on the model)
Adjustable feet

DOOR
To open the door, hold the door handle, press the inside handle (if available on your model) and pull the
door. Close the door by pressing it without excessive force until it clicks shut.

BEFORE THE FIRST WASH CYCLE

To remove any residual water used in testing by the manufacturer, we recommend that you carry out a
short wash cycle without laundry.
1. Turn on the water supply tap.
2. Close the door.
of the detergent dispenser.
3. Pour a little detergent (about 30 ml) into the main wash chamber
4. Select and start a short programme (see separate Programme Chart).

GB 5

PREPARATION OF THE WASHING

1.Sort the load according to...

Stain removal

Type of fabric / care label symbol

Cottons, mixed fibres, easy care/synthetics,
wool, handwash items.
Colour
Separate coloured and white items. Wash new
coloured items separately.
Loading
Wash items of different sizes in the same load to
improve washing efficiency and distribution in the
drum.
Delicates
Wash small items (e.g. nylon stockings, belts etc.)
and items with hooks (e.g. bras) in a washbag or
pillow case with a zip fastener. Always remove
curtain glides or wash curtains with the glides
inside a cotton bag.

Blood, milk, eggs etc. are generally removed by

the automatic enzyme phase of the programme.
For stains made by red wine, coffee, tea, grass,
fruit etc. add a stain remover to the main wash
chamber
of the detergent dispenser.
Pre-treat heavily-soiled areas with stain remover
if necessary.

2.Empty all pockets

Coins, safety pins etc. can damage your laundry
as well as the appliance drum and tub.

3.Fasteners
Close zips and fasten buttons or hooks; loose
belts or ribbons should be tied together.

Dyeing and bleaching

Only use dyes and bleaches that are suitable for
washing machines.
Follow the manufacturers instructions.
Plastic and rubber parts of the washing machine
can be stained by dyes or bleaches.

LOADING THE LAUNDRY

1. Open the door.
2. Unfold the laundry and place it loosely in the
drum. Observe the load sizes given in the quick
reference guide.
Note: Overloading the machine reduces the
wash efficiency and encourages creasing.
3. Close the door.

DETERGENTS AND ADDITIVES

Keep detergents and additives in a dry
place out of the reach of children.
The type of detergent depends on:
type of fabric (cottons, easy care/synthetics,
delicate items, wool).
Note: Use only specific detergents for wool.
Colour.
washing temperature.
Degree and type of soiling.
Remarks:
Whitish residues on dark fabrics are due to the
insoluble water softeners in modern phosphatefree detergents. If you notice this problem, shake
or brush the affected items or use a liquid
detergent.
Use only detergents and additives specifically
produced for domestic washing machines.
When using descaling agents, dyes or bleaches
for the pre-wash, make sure that they are
suitable for use in domestic washing machines.
Descalers could contain products which could
damage your washing machine.
Do not use any solvents (e.g. turpentine,
benzine). Do not wash fabrics in the machine
which have been treated with solvents or
flammable liquids.
Do not use liquid detergent for the main wash
when having activated the prewash option (if
available on your model).
Do not use liquid detergents when activating the
Start Delay function (if available on your
washing machine).

Dosage
Follow the dosage recommendations on the
detergent pack. They depend on:
Degree and type of soiling
size of wash full load: follow the detergent
manufacturers instructions;
half load: 3/4 the amount used for a full load;
minimum load (about 1 kg):
1/2 the dose recommended for a full load
water hardness in your area (request information
from the water company). Soft water requires
less detergent than hard water (refer to the
water hardness table in the operating
instructions).
Note:
Too much detergent can result in excess foam
formation, which reduces washing efficiency.
If the washing machine detects too much foam, it
may prevent spinning. Insufficient detergent may
result in grey laundry in time and also calcifies the
heating system, drum and hoses.

GB 6

Pouring in the detergents and additives

The detergent drawer has three chambers (fig. A).

Separator

Prewash Chamber
Detergent for the prewash
Main Wash Chamber
Detergent for the main wash
Stain remover
Water softener

Softener Chamber
Fabric Softener
Liquid starch
Pour additives only up to the MAX mark.

Type 1 basin

Using bleach
Wash your laundry with the desired programme (Cotton,
Synthetics), adding an appropriate amount of bleach to the
SOFTENER chamber (close the detergent dispenser carefully)
Immediately after the end of the programme, start the Rinse and
Spin programme to eliminate any residual bleach smell; if you
want, you can add softener.
Never put both chlorine bleach and softener into the softener
chamber at the same time.

Separator

Rails

Using starch
Select the Rinse and Spin programme and check that the spin
speed is set to not more than 800 rpm.
Start the programme, pull out the detergent dispenser so that you
can see approximately 3 cm of the softener chamber.
Pour the starch solution prepared into the softener chamber
while the water is running into the detergent dispenser.

Position the liquid detergent separator in the main

wash chamber.
When you use a liquid detergent (recommended for non pre-wash
programmes), position the separator in the main wash chamber
on the guides so that it touches the bottom of the chamber
then pour in the detergent until it reaches the full mark.

Type 2 basin
Separator

Remember to remove the separator when you use a powder

detergent.

GB 7

REMOVING THE FILTER/DRAINING

RESIDUAL WATER
We recommend that you check and clean the filter
regularly, at least two or three times a year.

Especially:
If the appliance does not drain correctly or if single spin
cycles do not take place.
If the Clean filter indication lights up:
IMPORTANT: make sure the water has cooled
before draining the appliance.
1. Switch off the appliance and unplug it.
2. Remove the plinth or open the cover (depending on
the model) by using the separator of the detergent
dispenser (fig. A / B).
3. Place a bowl beneath the filter. If the filter is located
behind the plinth (see pictures A e C), use a wide
and very flat container with a maximum height of 2 cm.
4. Open the filter but do not remove it completely.
Slowly turn the filter counterclockwise (fig. C) until the
water begins to drain out.
5. Wait until all the water has drained.
6. Now unscrew the filter completely and extract it.
7. Tilt the appliance forwards carefully to allow the water
to flow out.
8. Clean the filter and the filter chamber.
9. Check that the pump impeller can still rotate.
10. Re-insert the filter and screw it in clockwise as far as it
will go.
11. Pour about 1 l of water into the detergent dispenser to
reactivate the ecosystem. Check that the filter is
inserted properly and securely.
12. Reinstall the plinth or the cover, depending on the
model.
13. Plug in the appliance again.
14. Select a programme and start it.

GB 8

B
C

CARE AND MAINTENANCE

Appliance exterior and control panel

Door seal

Can be washed down with a soft, damp cloth.

A little neutral detergent (non abrasive) can also
be used
Dry with a soft cloth.

Clean with a damp cloth when necessary.

Check the condition of the door seal regularly.

Appliance internal parts

After each wash, leave the door open for some
time to allow the inside of the appliance to dry.
If you never or seldom wash your laundry at
90C, we recommend to occasionally run a 90C
programme without laundry, adding a small
amount of detergent, to keep the interior of the
appliance clean.

Filter
Check and clean the filter regularly, at least two
or three times a year (see Removing the filter /
Draining residual water)

Water supply hose

Check the hose regularly for brittleness and
cracks.
Regularly check and clean the mesh filter inside
the inlet hose (see Cleaning the mesh filter in
the water supply hose(s)).

Do not use flammable fluids for cleaning the appliance.

Detergent drawer
Clean the detergent dispenser regularly, at least three or
four times a year to prevent a build-up of detergent.
1. Press PUSH and extract the dispenser drawer.
2. Remove the cover grid from the fabric softener compartment.
Remove the separator from the main wash compartment by
pulling it upwards (see dark arrows).
3. Wash all the parts under running water.
4. Clean detergent from the dispenser with a damp cloth.
5. Refit the separator and the cover grid in the detergent dispenser
and fit the dispenser back inside its housing.

Inlet hose
If a supply hose shows a damage, replace it by a new hose of the
same type, available through our After-Sales Service or your
specialist dealer.
Contact our After-Sales Service team or specialist dealer to obtain a
replacement hose.

Cleaning the mesh filter in the water supply hose(s)

1. Close the tap and loosen the inlet hose on the tap.
2. Clean the internal mesh filter and screw the water inlet hose back
onto the tap.
3. Now unscrew the inlet hose on the rear of the washing machine.
4. Pull off the mesh filter from the washing machine connection
with universal pliers and clean it.
5. Refit the mesh filter and screw the inlet hose on again.
6. Turn on the tap and check that the connections are water-tight.
GB 9

TROUBLESHOOTING GUIDE
The appliance is fitted with automatic safety functions that detect faults at an early stage and allow the safety
system to react appropriately. These faults are frequently so minor that they can be dealt with a few minutes.
Problem
The machine will not
turn on and no lamps
are lit

Causes, Solutions, Suggestions

The plug has not been properly inserted in the socket.
The socket or fuse is faulty (use another lamp or electrical device to test the
socket).
The On/Off switch (if present) has not been pressed.
The door has not been closed correctly.

The machine will not

start even though the
Start button has been
pressed
The machine stops
The Rinse Hold function (if present) is turned on and the Anticrease light
during the programme
goes on in the programme sequence indicator; terminate Rinse Hold
and the Start light
by pressing the Start button or by choosing and starting the Drain
flashes
programme.
the programme has been changed: select the new programme and press
Start.
The programme has been interrupted and the door opened: close the door
and re-start the programme by pressing Start.
The appliance's safety system has been activated (see Description of red
indications).
The water tap is not open or the water inlet hose is kinked (Water tap
closed indication lights up).
The dispenser contains The separator in the main wash chamber has not been correctly fitted or is
not suitable for the use of powder and liquid detergents (see Detergents and
detergent and/or
additives).
additive residue
The water level is insufficient; the mesh filters of the water supply may be
blocked (see Care and maintenance).
The washing machine
The transport bolts have not been removed; Before using the machine, it
vibrates during the spin
is imperative that the transport bolts are removed.
cycle
The appliance is not level/not standing firmly on all four feet (see separate
Installation Guide).
The washing machine has an imbalance detection and correction system. If
Final spin results are
individual heavy items are loaded (e.g. bathrobes), this system may reduce the
poor
spin speed automatically or even interrupt the cycle in order to protect the
washing machine .
Heavy items may prevent the spin cycle from being carried out; add small
items and repeat the spin cycle.
The excessive formation of foam may prevent the spin cycle from being
carried out; select and start the Rinse & Spin programme. Avoid using
excessive amounts of detergent (see Detergents and additives).
The Variable Spin button (if present) has been set to a low spin speed or
the No Spin option (if present) has been activated.
It is normal for the washing machine to adjust to factors that might affect the
The programme time
duration of the wash cycle, e.g. the excessive formation of foam, an
initially shown on the
unbalanced load of very heavy items or extended heating time due to a low
display can be
lengthened/shortened water temperature.
For reasons like these, the wash time is recalculated and up-dated if necessary.
by a given amount of
time (only on appliances On some displays (depending on the model), an animation appears
with a display indicating during such update periods.
remaining programme
time)

GB 10

Description of red indications

The red light
will go on
(if fitted to the
appliance)

Alphanumeric
indications shown
on the display
(on models fitted
with them)

Description
Cause
Solutions

E00

The appliance has insufficient or no water supply.

The Start light goes on.
Check that:
The water tap is fully open and the water pressure
is sufficient.
The water supply hose is kinked.
the mesh filters of the water supply could be
blocked (see Care and maintenance.
The water hose is frozen up.
When the problem has been resolved, re-start the
programme by pressing the Start button. If the
fault occurs again, contact the After-Sales Service
[see next chapter).

E01

The water is not pumped out of the washing

machine. The appliance stops in mid programme;
unplug the appliance and check if:
there are kinks in the drain hose.
the filter or pump is blocked (see chapter
Removing The Filter/Draining Residual Water;
make sure the water has cooled before
draining the appliance).
the water in the water inlet hose is frozen.
When you have resolved the problem, turn the
programme selector to Off/O to reset the
appliance; next re-start the desired programme. If
the fault occurs again, contact the After-Sales
Service [see next chapter).

Water Tap
Closed

Clean Pump

Electrical module fault

E02
Service

E03
Fod
E04

Door locking error

Unplug the appliance and turn the programme

selector to Off/O, then turn the appliance ON
again. Select the Drain/Spin programme and restart within 15 seconds.
Turn the appliance OFF by turning the programme
selector to Off/O; Open and close the door again
with more force then reselect the programme and
press Start.
If any of the faults described above persists, unplug
the appliance, turn off the water supply and contact
our After-Sales Service (see next chapter).

GB 11

AFTER-SALES SERVICE
Before contacting After-Sales Service:

Specify:
The nature of the problem.
The washing machine model.
The service code (number after the word
SERVICE)

1. Try to remedy the problem yourself (see

Troubleshooting Guide).
2. Restart the programme to check whether the
problem has solved itself.
3. If the washing machine continues to function
incorrectly, call After Sales Service.

The After Sales Service sticker can be found

inside the door.
Your full address.
Your telephone number and area code.
After-Sales Service phone numbers and
addresses are given on the guarantee card.
Alternatively, consult the dealer where you
purchased the appliance.

ACCESSORIES
For some models, you can obtain accessories from
our After-Sales Service or from an authorised
dealer:
a Pedestal Drawer which can be installed
beneath your washing machine It raises your
machine to allow for more comfortable loading
and unloading, as you now no longer need to
bend as far to access the unit. Furthermore, it
offers a great space-management tool and
storage solution.
a Stacking Kit by means of which you can fix
your dryer on top of your washing machine and
thus effectively save space.

Some models are able to be installed under your

kitchen worktop; in that case, please contact our
After-Sales Service (see above). Attention:
the appliance MUST be installed under a
continuous worktop.
according to the legal safety regulations, the
installation of the appliance MUST be carried out
by an authorized technician or by our After-Sales
Service.
the appliance MUST be installed using the
intermediate cover panel of the UBS Base Set
which can be obtained from specialist dealers or
our After-Sales Service.

GB 12

BUILT-IN MODELS
INSTALLATION TIPS
Washer dryer housing dimensions:

Due to the need for the washer dryer filter to be cleaned periodically the plinth should be easily
removable.
For easy care and maintenance water supply and drain should not be positioned behind the appliance.
The electrical connections should be positioned so that the appliance can be disconnected when fitted in
position.

GB 13

FITTING A DCOR DOOR TO THE APPLIANCE

The appliance front part has been fitted to accommodate the hinges so that the door can be opened either
from the left or from the right hand side.
Proceed as follows:
1. Screw the hinges onto the dcor door, if a dummy drawer front is also being used ensure it to be fastened
to the top edge of the door. Ensure the gap between door and drawer matches the units either side.
2. Fix the two hinge plates to the front of the washer dryer using the two plastic backing pieces.
Note: an 8mm box spanner can be used to screw the thread cutting screws into position.
3. Fasten the two magnetic catches to the opposite side to the hinges and ensure the metal straps are
fastened to the back of the door.
4. Locate the hinges on the door into the two hinge plates on the appliance.
5. If adjustment is necessary this can be achieved by either the hinge plates (vertical) or by the hinge fixing
screws (horizontal).

FITTING A FULL HEIGHT DOOR

If a full height door is to be fitted (no dummy drawer front is being used) a top hinge hole has to be drilled
in the door.
The distance between the two hinge hole centres is 360 - 384mm and the distance from the edge of the
door is 21.5mm.
The hinge hole should be max 12mm deep and its diameter 35mm: make sure you do not drill through the
door.
The two fixing holes for the hinge screws are 2mm.

DCOR STRIP
A dcor strip can be screwed into position on the edge of the washer dryer. If needed, the strip can be cut
to be adjusted to your furniture but normally this will not be necessary.

TO LINE UP

TO DRILL

GB 14

5019 301 20032a

SM2424/05

Stampa TLF 25/01/2010

461307267