HC1 A Manual EN

TECORP Electronics
HC1-A User Manual
Contents
1. Introduction----------------------------------------------------- 1
1.1 Confirmations upon delivery ------------------------------- 2
1.2 Nameplate information -------------------------------------- 2
2. Safety Precautions -------------------------------------------- 2
2.1 Before delivery of current ----------------------------------- 2
2.2 In delivery of current ---------------------------------------- 4
2.3 In running ----------------------------------------------------- 4
3. Inverter standard specifications ---------------------------- 4
3.1 Individual specifications ------------------------------------ 4
3.2 Common specifications ------------------------------------ 6
4. Storage & Installation ---------------------------------------- 7
4.1 Storage --------------------------------------------------------- 7
4.2 Location ------------------------------------------------------- 7
4.3 Position -------------------------------------------------------- 8
5. Wiring ---------------------------------------------------------- 9
5.1 Main circuit schematic diagram ---------------------------- 9
5.2 Terminals ----------------------------------------------------- 10
5.3 Standard Connection Diagram----------------------------- 12
5.4 Wiring Precautions ------------------------------------------ 13
6. Using the digital operator ------------------------------------ 15
6.1 Explanations of the digital operator----------------------- 15
6.2 Display data -------------------------------------------------- 17
6.3 Instructions of the digital operator ------------------------ 18
1
TECORP Electronics
HC1-A User Manual
7. Trial Operation ------------------------------------------------ 19

7.1 Inspection before operation -------------------------------- 19
7.2 Trial operation procedures --------------------------------- 19
8. Function List ------------------------------------------------- 20
9. Explanations of the functions ------------------------------- 27
10. Maintenance,Inspection&Trouble shooting-------------- 72
10.1 Precautions about maintenance and inspection -------- 72
10.2 Regular Inspection items---------------------------------- 72
10.3 Error information and its troubleshooting -------------- 74
10.4 Error and its analysis -------------------------------------- 75
11. Peripheral devices and specifications of options -------- 77
11.1 Peripheral devices------------------------------------------ 77
11.2 Proper specifications of options ------------------------ 78
12. Appendices --------------------------------------------------- 81
12.1 Application demonstrations------------------------------- 81
This operation manual is 1.37 versions. Specifications are

subject to change without notice for ongoing modifications and
improvements.
TECORP Electronics
HC1-A User Manual
1. Introduction
Thank you for purchasing our high quality HC1-A series inverters.
Before installation and operation please read these instructions in
this manual thoroughly. For your safety, the product should only be
installed, tested and adjusted by professional personnel. If you have any
questions or problems, please contact our local agency.
The information contained in this manual is subject to change
without notice.
WARNING Indicates precautions that, if not avoided, could

result in death or serious injury to personnel.
! CAUTION Indicates precautions that, if not avoided, could
result in minor or moderate injury to personnel and damage to
equipment.
WARNING
Always turn off the input power supply before wiring.
Do not touch any inner part of the inverter when the charging lamp is
still on shortly after the AC power is cut off.
Do not check signals while the inverter is running.
Do not attempt to modify or alter the inverter by yourself, doing so
can result in electrical shock or injury or even explosion.
Be sure to ground the E terminal.
! CAUTION
Do not perform voltage withstand tests on the inverter.
Never connect the AC main circuit power supply to output terminals
U.V and W.
A CMOS IC is used in the control board. Handle the control board
and CMOS IC carefully. The CMOS IC can be destroyed by static
electricity if touched directly.
Installation, testing and maintenance must be performed by
professional personnel.
The inverter should be discarded as industrial waste. Avoid burning.
TECORP Electronics
HC1-A User Manual
1.1 Receiving
Before unpacking please check the following:
Inspect the entire exterior of the inverter to see there are any scratches
or other damage resulting from shipping.
Check if there is an inverter and an operation manual in the package
as soon as you open the package.
Check the model on the nameplate on the side of the inverter to see if
this is the right model you want.
Check if there is something wrong with the inner parts, wiring and
circuit board.
Use a screwdriver or other tools to check for tightness.
Check if there is any other things in the machine.
Check if the operator buttons are all right.
Check if the optional device you ordered is contained in it.
1.2 Nameplate information

MODEL
INPUT
HC1A07D543B
3 Ph 400V 50/60Hz
OUTPUT
3 Ph 400V 17.5A 7.5KW
Freq- Range:
0.1400Hz
TECORP ELECTRONICS CO., LTD.
MODELHC1 A 07D5 43 B
Software version
Voltage grade 43 means 3 phases 400V
Inverter capacity,07D5 means 7.5KW
Serial number
Product name
TECORP Electronics
HC1-A User Manual
2.Safety precautions
2.1 Before delivery of current
! CAUTION
Check to be sure that the voltage of the main circuit AC power
supply matches the rated voltage of the inverter.
! CAUTION
E symbol is the ground terminal, Be sure to ground the ground
terminal.
Do not Connect electromagnetic switches or contactors to the output
circuits.
! WARNING
R.S.T terminals are power input terminals, never mixed with U.V.W
terminals. Be sure that the wiring of the main circuit is correct.
!CAUTION
Always hold the case when carrying the inverter. If the inverter is
held by the front cover, the main body of the inverter may fail,possible
resulting in injury.
Mount the inverter to a metal or other noncombustible material.
Install the inverter in a safe site, avoid high temperature, direct
sunlight, humid air or water.
Keep the inverter from the reach of children or non-workers.
Install a cooling fan or other cooling device when installing more
than one inverters in the same enclosure so that the temperature of the
air entering the inverter is below 40.
X
Check to be sure that the front cover
KM
is attached before turning on the
u
power supply. Do not remove the front
v
M
Inverters
cover during operation.
w
Do not install the inverter in a space
with explosive gas.
If the inverter is used at or above
1000m above seal level, the cooling
X
efficiency will be worse, so please run
it downgraded.
Do not connect contactors and related capacitor or voltage
dependent resistor etc,to the output circuits.
If it is a must to connect such devices, be sure there is no inverter
output when operating these devices.Otherwise,it will result in damage
3
TECORP Electronics
HC1-A User Manual
to the inverter. The installation diagram like this is forbidden.

Do not connect contactor to the input circuits. The service life of the
inverter can be much longer if you start or stop the inverter by pressing
the buttons FOR or REV,especially in those frequently starting and
stopp conditions.
2.2 In delivery of current

WARNING
Do not remove connectors on the inverter when in delivery of current.
Always have the protective cover in place before delivery of current
to avoid electrical shock.
2.3 In running
WARNING
Never add or remove motor group while in running, the surge
current it created will cause damage to the inverter, even burn-up of
the main circuit.
WARNING
Never remove the front cover of the inverter while in running.
Do not come close to the machine when the fault restart function is
used. If the alarm is cleared, the machine may start moving suddenly.
The function of the STOP button can only be available after setting.
It is different from the emergency stop button. Please note.
! CAUTION
Do not touch the heat sink, braking resistor, or Braking Resistor
Unit. These can become very hot.
Be sure that the motor and machine is within the applicable ranges
before starting operation.
Do not check the signals while the inverter is running.
Be careful when changing inverter settings. The inverter has been
set to suitable for general using in factory.
Do consider the noise,vibration,and the speed limit of the motor and
the mechanical devices when the inverter is running at or above the
frequency of 50Hz.
4
TECORP Electronics
HC1-A User Manual
3. Standard Specifications
3.1 Individual Specifications
MODEL
Input Voltage
Power
(KW)
Driver
Capacity
(KVA)
HC1A00D423B
HC1A0D7523B
HC1A01D523B
HC1A02D223B
HC1A0D7543B
HC1A01D543B
HC1A02D243B
HC1A03D743B
HC1A05D543B
HC1A07D543B
HC1A001143B
HC1A001543B
HC1A18D543B
HC1A002243B
HC1A003043B
HC1A003743B
HC1A004543B
HC1A005543B
HC1A007543B
HC1A009043B
HC1A011043B
HC1A013243B
HC1A016043B
HC1A018543B
HC1A020043B
HC1A022043B
HC1A025043B
1/3220V
1/3220V
1/3220V
1/3220V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
3400V
0.4
0.75
1.5
2.2
0.75
1.5
2.2
3.7
5.5
7.5
11
15
18.5
22
30
37
45
55
75
90
110
132
160
185
200
220
250
HC1A028043B
3400V
280
1.0
2.0
2.8
4.0
2.2
3.2
4.0
6.8
10
14
19
26
32
37
52
64
72
84
116
134
160
193
230
260
290
325
368
Output
Current
(A)
2.5
5.0
7.0
10
2.7
4.0
5.0
8.5
12.5
17.5
24
33
40
47
65
80
91
110
152
176
210
253
304
340
380
426
483
Suitable
Motor
(KW)
0.4
0.75
1.5
2.2
0.75
1.5
2.2
3.7
5.5
7.5
11
15
18.5
22
30
37
45
55
75
90
110
132
160
185
200
220
250
412
540
280
5
TECORP Electronics
HC1-A User Manual
MODEL
Input Voltage
Power
(KW)
Driver
Capacity
(KVA)
HC1A030043B
HC1A031543B
HC1A037543B
HC1A041543B
HC1A045043B
3400V
3400V
3400V
3400V
3400V
300
315
375
415
450
450
461
550
610
665
Output
Current
(A)
580
605
800
880
960
Suitable
Motor
(KW)
300
315
375
415
450
3.2 Common Specifications

ITEM
Control Method
Input Power Supply
Frequency Control
Frequency Range
Frequency
Accuracy
Frequency Setting
Resolution
Output Resolution
Operator Setting
Method
Analog Setting
Method
Other functions
General Control
6
Acceleration/Dec
eleration time
V/F Curve
Torque Control
Multi-function
input terminals
HC1-A
SPWM
400V Power Supply340 VAC - 460VAC
220V Power Supply180 VAC 250 VAC
0.10~400.00Hz
Digital0.01%-10~40
Analog0.1% 2510
Digital0.01Hz
Analog1% of Max Operating Frequency
0.01Hz
Pressor or to set
0-5V / 0-10V
4-20mA / 0-20mA
Frequency up/lower limit, start frequency, stopping
frequency, three skip frequencies can be
individually set.
0.1-6500s four selectable combinations of
independent acceleration and deceleration
setting.
Set V/F curve at will.
Max Torque 10.0% Max Output Voltage. The
starting torque can reach 150% at 1.0Hz
6 multifunction input terminals for 8
multi-speed, easy PLC, 4 Accel/Decel
time,UP/DOWN command, external
emergency stop.
TECORP Electronics
Protection Function
ITEM
Communication
Control
Operating
Temperature
Humidity
Vibration
Instantaneous
over current
Over Load
Motor Overload
Protection
Over Voltage
Under Voltage
Momentary
Power Loss
Heat Sink over
heat
Multi-function
output terminals
Other functions
Digital operator
monitor
HC1-A User Manual
HC1-A
RS485
-10~40
0-95% relative humidity
0.5G or lower
Approx. 200% rated current.
Inverter:150% 1 minute.
Electronic thermal overload relay.
23 series: DC bus over 400Vdc
43 series: DC bus over 800Vdc
23 series: DC bus voltage drop 200Vdc
43 series: DC bus voltage drop 400Vdc
0-2 seconds: The inverter can be restarted by
speed search.
Protected by thermistor
5 multifunction output terminals for the
displaying and warning of on-running, zero
speed, counting and external fault information.
AVR, Decelerating stop or free-stop, DC brake,
auto restart tracking, easy PLC auto energy
saving, adjustable carrier Frequency (Max
20KHz) etc.
Frequency command,output frequency, speed
output current, output voltage. DC bus voltage
and rotation direction.
4.Storage &Installation
4.1 Storage
This product must be stored in its package box before installation.Pay
more attention to the followings when in storage.
It must be stored in a dry place without rubbish or dust.
7
TECORP Electronics
HC1-A User Manual
The suitable temperature for storage is between -20and +65.

The relative humidity required is 0-95%,no condensation.
There is no corrosive gas or liquid.
Its better to lay the inverter in its original package on a shelf.
4.2 Location
Note: The working conditions of the inverter will affect its service
life,please install the inverter under the following conditions.
Ambient operating temperature -10 to 40.
IP rating: IP 20 for all models.
Protected from rain moisture.
Shielded from direct sunshine.
Free from metallic particles and corrosive gas.
Free from excessive vibration.
4.3 Positioning
120
There must be enough space left around the inverter for easy
maintenance and effective ventilation.See Diagram 1.
The inverter must be installed with heat sink ribs oriented vertically
for effective ventilation..
If there is any instability when installing the inverter, please put a flat
board under the inverter bottom base and install again. If the inverter is
installed on a loose surface, stress may cause damage in main circuit.
The inverter should be installed on non-combustible materials, such
as iron plates.
If several inverters are installed together in one cabinet, please add
heat dissipation plates and provide enough space between the inverters.
See Diagram 2.
50
50
HCI-A
CAUTION
Hig h vol ta ge In aid e
WARNING
Do no t c on nect AC po we r t o o ut put tu rbin a ls( U.V.W )
Dis ch ar gi ng time le g rea te r t ha n 5 an co ne s.
Do no t Lns pect comp one nts un less I ns ide H ARGE
120
la mp Is tu rn ed o ft.
Unit:mm
Diagram 1
Diagram 2
TECORP Electronics
HC1-A User Manual
5. Wiring
5.1 Main circuit schematic diagram
Power supply: Verify that the inverter rated voltage
coincides with AC power supply voltage.
No fuse breaker or ground fault interrupter.
Magnetic contactor
Note: Dont use the magnetic contactor as the power
supply on/off button for the inverter.
AC reactor for power factor improvement.
HCI-A
TECORP Inverter (HC1-A series)
C A U T I O N
Hig h vo ltag e I nai de
W A R N I N G
Do n ot c on nec t AC powe r t o ou tp ut t ur bin als( U.V.W)
Disc har gi ng t ime le gr ea te r th an 5 ancon es .
Do n ot L ns pec t co mpo ne nt s un less I nsid e H AR GE
la mp I s tu rn ed o ft.
3 phases squirrel cage induction motor.
TECORP Electronics
HC1-A User Manual
5.2 Terminals
5.2.1 Main Circuit Terminals Arrangement
HC1A00D423B-HC1A02D223B
Pr
S
P1
HC1A001143B-HC1A030043B
R
5.2.2 Control circuit terminals arrangement

FA FB FC
KA KB
UPF
EV SPL SPM SPH RST DCM REV FOR

DRV +10 VI AI ACM AM
RS- RS+
FA
FB
FC
KA
KB
IPV
UPF
DRV
DCM
SPH RST REV FOR +10 VI AI ACM AM

HC1A02D223B
SPL
RS-
SPM
RS+
UPF DRV FOR REV DCM RST SPH SPM SPL P24 AM
ACM AI
VI
+10
EKB EKA EFC
HC1A02D223B
10
EFB
EFA
PR
TECORP Electronics
HC1-A User Manual
5.2.3 Function description of main circuit terminals

SYMBOL
R.S.T
P.Pr
P.P1
P.N
U.V.W
E
FUNCTION DESCRIPTION
Input terminals of AC line power.
External braking resistor terminals.
External DC reactor terminals.
External Braking unit terminals.
Output terminals to motor.
Ground terminal.
5.2.4 Function description of control circuit terminals

Symbol
FOR
REV
RST
SPH
SPM
SPL
DCM
EV(IPV)
P24
+10
VI
AI
ACM
DRV
UPF
FA(EFA)
FB(EFB)
FC(EFC)
KA(EKA)
KB(EKB)
AM
RS+RS-
Functions
Multi-function input1
Ground common for input
terminals
+12V power supply
+24V power supply
Power supply for analog frequency
Analog frequency reference
input(voltage)
Analog frequency reference
input(current)
Common for analog input signal
Multi-function output terminal 1
Factory setting
Forward run
Reverse run
Reset
High speed
Medium Speed
Low Speed
Max output current 200mA

Max output current 200mA
+10V
0~+10V corresponding to
highest operating frequency
4~20mA corresponding to
highest operating frequency
Optical couple output DC
24V/100mA

Digital frequency output terminal
RS-485 communications
Fault Relay output(N/O or

N/C) 3A/250VAC,3A/30VDC
Fault Relay output (N/O)
3A/250AC,3A/30VDC
0-10V
11
TECORP Electronics
HC1-A User Manual
5.3 Standard Connection Diagram

The whole wiring is divided into two parts. Main circuit terminal
connections and control circuit terminal connections. Users can see the
main circuit terminals and the control circuit terminals after removing
the outer cover. The terminals must be connected correctly as the
following diagrams.
The following diagram shows the standard connection of HC1-A.
Braking Resistor
Pr
P
R
Ac power supply
U
V
W
S
T
Motor
VI
ACM
KA
Multi-function output <relay N/0>
KB
3A/250VAC 3A/30VDC
EV(IPV)
+12V
AI
FC
Multi-function output <relay N/0 N/C>
FA
FB
3A/250VAC
3A/30VDC
DRV
Multi-function output <OP>

24V/100mA
VR(+10V)
10K
Analog Current
input
FOR
REV
SPH
SPM
SPL
UPF
DCM
RST
AM
Analog frequency output

0~10V
DCM
ACM
RS+
HC1A00D423B~HC1A02D223B
RSHC1A0D7543B~HC1A03D743B
Dc Reactor
R
Ac power supply
Braking Resistor
P1
Pr
U
V
S
T
Motor
E
VR(+10V)
10K
Analog Current
input
KA
VI
ACM
Multi-function output <Relay N/O>

KB
3A/250VAC 3A/30VDC
EV(IPV)
+12V
AI
FC
Multi-function output <Relay N/O N/C>
FA
FB
3A/250VAC
SPH
DRV
SPM
SPL
UPF
DCM
Multi-function output <Relay OP>

24V/100mA
FOR
REV
RST
AM
DCM
ACM
12
RS+
RS-
HC1A05D543B~HC1A07D543B
3A/30VDC
Analog frequency output

0~10V
TECORP Electronics
HC1-A User Manual
Motor
5.4 Cautions on Wiring

5.4.1 For main circuit wiring
No Fuse Breaker between the power supply and the input terminals
(R.S.T).
(If using ground fault interrupter, please choose the one corresponding
to high frequency)
Never connect AC power to the output terminals of U.V.W on the
inverter.
Output wires mustnt be in touch with the metal part of the outer
cover, or it will cause short-circuit.
Phase-shifting capacitor,LC,RC noise filters,etc,can never be
connected between motor and output terminals (U.V.W)
The main circuit wire must be enough far away from other control
equipments.
If there is a relatively long distance between the inverter and the
motor, please lower the carrier frequency. Because the high leak current
will cause damage to the inverter and other equipments.
If the wire is more than 15m for 220V class products (or 30m for
13
TECORP Electronics
HC1-A User Manual
400V class products) between the inverter and the motor, please choose
a AC motor special for inverters or add a AC reactor on the output side
of the inverter, because a very high dV/dT produced in the motor coil
will cause damage to the insulation of the motor.
Specifications for NFB and Wire
220V
Class
400V
Class
Model
HC1A00D423B
HC1A0D7523B
HC1A01D523B
HC1A02D223B
HC1A03D723B
HC1A0D7543B
HC1A01D543B
HC1A02D243B
HC1A03D743B
HC1A05D543B
HC1A07D543B
HC1A001143B
HC1A001543B
HC1A18D543B
HC1A002243B
HC1A003043B
HC1A003743B
HC1A004543B
HC1A005543B
HC1A007543B
HC1A009043B
HC1A011043B
HC1A013243B
HC1A016043B
HC1A018543B
HC1A022043B
HC1A030043B
Screw
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M5
M6
M6
M6
M8
M8
M8
M8
M8
M10
M10
M10
M12
M12
M16
M16
M16
Wire size
2~5.5
2~5.5
2~5.5
3.5~5.5
5.5
2~5.5
2~5.5
2~5.5
3.5~5.5
3.5~5.5
5.5
8
8
14
22
22
30
50
38~100
38~100
38~100
60~100
60~100
100~200
250~325
325
250*2p
Note: The parameters above are only for reference, not a standard.
5.4.2 For control circuit wiring (signal line)

Separate control circuit wire from main circuit wire and other
high-power lines.
Use twisted-pair or shielded twisted-pair cables for control circuits to
prevent operating faults. The size should be 0.5-2mm2..
14
TECORP Electronics
HC1-A User Manual
Use the control terminals correctly according to your needs.
5.4.3 Grounding
Grounding terminal:E
220V class: The third grounding method. (grounding resistance should
be 100 ohm or lower.)
380V class: Special grounding method. (earth resistance should be 10
ohm or lower.)
Choose grounding wires according to the requirements of the electric
equipment.
Avoid sharing grounding wire with other large power equipment. The
grounding wire should be kept away from the power supply wires.
The grounding method for several inverters together should be done
as the first and second diagrams. Avoid the third diagram.
The shorter grounding wire is the better it is.
1Correct
2Correct
3Wrong
15
TECORP Electronics
HC1-A User Manual
6. Description of Digital Operator
Operation Mode Indicators

forward run, reverse run,
frequency, current, Speed.
Forward or reverse run key
FOR
REV
HZ
F/
R
R/min
PROG
Numerical change key

ENTER
Run key
STOP
RUN
RESET
HC002
Operation Mode Indicators
forweard run, reverse run,
frequency, current, Speed.
Forward or reverse run key
FOR REV
HZ
A ROTT
FOR
REV
PROG
DISP
SET
Numerical change key
Run key
RUN
HC001
16
STOP
TECORP Electronics
HC1-A User Manual
6.2 Display status

6.2.1 Display status description
Indicator
Status
FOR
On
Forward run
REV
On
Reverse run
HZ
On
Display set frequency or output frequency
On
Display output current
ROTT
On
Display motor speed
HZ A
On
Display DC voltage
ROTT
On
Display output voltage
HZ
ROTT
On
Display counting data
On
Display inverter temperature
HZ A ROTT
Explanation
6.2.2 Explanation to data display

Display item
050.00
5.5
1440
30.0
CD100
EOC.A
Indicator
HZ
ROTT
HZ
A
HZ
on
Explanation
Present set frequency or
output frequency
Current
Motor speed
ROTT
Present inverter heat sink

temperature
Function item
Error information
17
TECORP Electronics
HC1-A User Manual
6.3 Operation Example

Procedures
Power on
Data
dsp.1 flashing
Display
Explanation
FOR
Hz
FOR
Hz
FOR
Hz
FOR
Hz
FOR
Hz
FOR
Hz
FOR
Hz
Switching to display running

frequency.
FOR
Switching to display output

current.
FOR
ROTT
uEr1.3
000.00
P RO G
E NTER
CD000
000.00
50.00
E NTER
PROG
RUN
DISP
END 50.00
CD001
050.00
50.00
50.00
0.00 50.00
0005.0
Self inspection after power on,

showing its version number
(flashing),then its set frequency.
Function number Cd000.
Modify the value of Function

CD000. Display:END50.00
CD001 Withdraw from the
programming status.
Display:Forward run status and
set frequency.
DISP
01440
Switching to display rotating

speed.
DISP
PROG
F/R
050.00
050.00
050.00
030.00
ENTER
STOP
030.00
030.00
Note: (1) means flashing

18
Return to main display,showing

set frequency.
FOR
Hz
REV
Hz
REV
Hz
Switching to frequency
adjustable status.
REV
Hz
Adjust the set frequency,that is

the value of CD000.
REV
Hz
Enter the new value which will

be remembered as CD000.
REV
Hz
means on
Stop.
TECORP Electronics
HC1-A User Manual
7. Trial Operation
7.1 The important check before running
Is there any wrong connected wires? Pay special attention to the
terminals:U.V.W;
Make sure the power supply wires are connected to R.S.T not U.V.W.
Is there any metal powder or other wires left on the base plate of the
inverter or at the terminals?
Is there any looseness in the parts of screws and terminals?
Is there any short circuit or earth fault in the output parts?
7.2 Trial operation procedures

Trial operation can be carried out by the digital operator.
Generally, trial operation is done at 5.00 Hz.
Procedures Data Display Indicator
Explanations
Self
inspection after power on,
POWER ON dsp1.1uEr1.3
FOR Hz
display version number, at last
000.00
display set frequency.
FOR Hz
Switching to data adjustable
000.00
status.
FOR Hz
Set a new frequency value that
050.00
is the new CD000 value.

FOR Hz
Confirm this new setting.
ENTER
050.00
RUN
050.00
STOP
050.00
FOR
FOR
Hz
Hz
Running at 50Hz.
Stop.
Note: means indicator on,

means indicator flashing
0 Means the number flashing
19
TECORP Electronics
HC1-A User Manual
8.Function list
Basic parameter
Function
Item
code
CD000
CD001
CD002
CD003
CD004
CD005
CD006
CD007
CD008
CD009
CD010
20
CD011
Parameter and Function List (Part 1)

Set range&function
Function
explanation
Main frequency
0.00~400.00Hz
Max output voltage
0.1V*
Base frequency
0.01~400.00Hz
Voltage at medium frequency 0.1V*
Medium frequency
0.01~400.00 Hz
Voltage at lowest frequency
0.1~50.0V
Lowest frequency
0.01~20.00 Hz
Max operating frequency
50.00~400.00 Hz
Frequency upper limit
0.01~400.00 Hz
Frequency lower limit
0.00~400.00 Hz
Parameter lock select
0:invalid 1:valid
00~10 only No.08
Factory setting
means to reset to
factory setting
Accel.Time 1
0.1~6500.0S
Decel.Time 1
0.1~6500.0S
Accel.Time 2
0.1~6500.0S
Decel.Time 2
0.1~6500.0S
Accel.Time 3
0.1~6500.0S
Decel.Time 3
0.1~6500.0S
Accel.Time 4
0.1~6500.0S
Decel.Time 4
0.1~6500.0S
CD012
CD013
CD014
CD015
CD016
CD017
CD018
CD019
CD020
Reserved
CD030
Factory
Setting
0.00
220/380
50.00
15/27.5
2.50
8.0/13.5
0.50
50.00
50.00
0.00
0
00
10.0/25.0
10.0/25.0
50.0
50.0
100.0
100.0
200.0
200.0
TECORP Electronics
HC1-A User Manual

Function
Set range &function
Item
Function
code
explanation
0:start from starting
frequency 1:start by
CD031 Start mode
former frequency track
CD032 Stop mode
0:decelerate to stop 1:free

run to stop
Factory
Setting
0
0:digital operator
CD033 Control Mode Select 1:external terminals
2:communications
0:digital operator
Frequency command 1:external terminals
CD034
method select
2:communications
Applied Parameter
CD035 Carrier frequency

CD036 Jog frequency
CD037 FOR/REV select
CD038
CD039
CD040
CD041
CD042
CD043
CD044
CD045
CD046
STOPkey
definition
0~15
0.00~400.00Hz
0:Reverse run forbidden
1:Reverse run available
5
5.00
1
0:STOP key ineffective in

remote control mode
1:STOP key effective in
remote control mode
Reserved
Starting Frequency
Stopping Frequency
Torque Boost
Skip Frequency 1
Skip Frequency 2
Skip Frequency 3
0.1~10.0Hz
0.1~10.0Hz
010%
0.00~400.00 Hz
0.00~400.00 Hz
0.00~400.00 Hz
0.5
0.5
2.0%
0.00
0.00
0.00
21
TECORP Electronics
HC1-A User Manual
Applied
Parameter

Function
Set range &function
Factory
Item
Function
code
explanation
Setting
Skip Frequency
CD047
0.00~2.00 Hz
0.5
Range
CD048 Reserved
CD049
CD050 Multi-input1(FOR) 00:invalid 01:run 02:forward
02
CD051 Multi-input 2(RST) run 03:reverse run 04:stop
03
CD052 Multi-input 3(RST) 05:for/rev run 06:jog
10
07:forward jog 08:reverse jog
CD053 Multi-input 4(SPL) 09:external emergency stop
17
CD054 Multi-input 5(SPL) 10:reset 11:reserved
18
CD055 Multi-input 6
19
12:overheat of motor 17:high
speed 18:medium speed
(SPL)
Input,Output Terminals
CD056
CD057
CD058
CD059
19:low speed 20:multi-speed1

21:multi-speed2
22:multi-speed3
23:accel/decel select1
24:accel/decel select2
00:Invalid 01:run mode
Multi-output
02:Fault signal 03:zero speed
1(DRV)
Multi-output 2(UPF) 04:Brake indication 05:Up to
setting frequency 06:Up to
Multi-output 3(FA
desired frequency1 07:Up to
FB FC)
desired frequency2 08:In
Multi-output 4
accelerating 09:In
(KA KB)
decelerating 10:Inverter
overload 11:Motor overload
13:Under voltage 14:Finish
indication for single stage
15:Finish indication for
process 16:counting arrival
27:Drafting arrival 28:PID
lower limit alarm 29:PID
upper limit alarm 30:Fan
running 31:Reserver
32:Braking resistor action
CD060 Multi-output 5(AM)

UP-to desired
CD061
frequency1 setting
22
01
05
02
00
1
0.00~400.00Hz
TECORP Electronics
Item
Function
code
CD062
CD063
CD064
CD065
Input Output Terminals
CD066
CD067
CD068
CD069
CD070
CD071
CD072
HC1-A User Manual

Set range & function
Function
explanation
UP-to
desired
0.00~400.00 Hz
frequency 2 setting
UP-to frequency setting
0.10~10.00 Hz
detection width
Counter set
00~65500
0:0~10V
1:0~5V
2:0~20mA 3:4~20mA
Analog input select
4:0~10V plus 4
20mA
Lower
analog 0.00400.00Hz
frequency set point
Lower
analog 0:positive
frequency bias direction 1:negative
Higher
analog 0.00~400.00Hz
frequency set point
Higher
analog 0:positive 1:negative
frequency bias direction
Negative bias reverse
0:invalid 1:valid
select
Analog output gain
0.0~100.0%
Up/down
function 0:recorded
select
1:non-recorded
Factory
Setting
0.00
0.50
00
0
0
0
50.00
0
1
100
1
CD073
Reserved
CD075
23
TECORP Electronics
HC1-A User Manual

Function
Item
code
Multi-section speed and simple PLC

24
Function
CD076
PLC mode select
CD077
Auto PLC select
CD078
CD079
CD080
CD081
CD082
CD083
CD084
CD085
CD086
CD087
CD088
CD089
CD090
CD091
CD092
CD093
CD094
CD095
CD119
PLC running
direction
PLC
accel/decel.time
Multi-speed 2
Multi-speed 3
Multi-speed 4
Multi-speed 5
Multi-speed 6
Multi-speed 7
Multi-speed 8
Timer 1
Timer 2
Timer 3
Timer 4
Timer 5
Timer 6
Timer 7
Timer 8
Reserved
Factory
setting
Set range & function explanation

0:normal running
0
1:externalcontrol four speed
2:external control multi
speed3:disturbance 4:inner
control multi speed
0:stop after one circle
0
1:circulating running 2:stop after
auto running one circlewith
STOP interval 3:auto
circulating runningwith STOP
interval
0~255(0:Positive 1:Negative)
0
0~65535
0.00~400.00Hz
0.00~400.00Hz
0.00~400.00Hz
0.00~400.00Hz
0.00~400.00Hz
0.00~400.00Hz
0.00~400.00Hz
0.0~6500.0s
0.0~6500.0s
0.0~6500.0s
0.0~6500.0s
0.0~6500.0s
0.0~6500.0s
0.0~6500.0s
0.0~6500.0s
15.00
20.00
25.00
30.00
35.00
40.00
0.50
10.0
10.0
0.0
0.0
0.0
0.0
0.0
0.0
TECORP Electronics
Protective function parameter
Item Function
code
CD120
CD121
CD122
CD123
CD124
CD125
CD126
CD127
CD129
CD130
HC1-A User Manual

Function
explanation
Stall prevention select
0:invalid 1:valid
Stall prevention level
0~200%
during accel
0~200%
during running
0~200%
during decel
Reserved
Over torque detection
0~200%
level Over torque
0.1~20.0s
detection time
Reserved
Rated voltage
Motor specifications
Special function parameter
CD131
Rated current
CD132
CD133
CD134
CD139
CD140
CD141
Motor poles
Rated rotational speed
Reserved
CD142
CD143
CD144
CD145
CD146
CD147
CD148
CD149
According to the motor

nameplate
According to the motor
nameplate
0210
009999
DC braking level
0.0~20.0%
DC braking time at
0.0~25.0S
starting
DC braking time at stopping
0.0~25.0S
Speed search time
0~20.0S
Speed search current level
0~200%
Power loss allowable
0:invalid 1:restart by
Momentary power ride
speed search
through time
0.1~5.0s
Number of auto restart
010
Auto voltage regulation
0:invalid 1:valid
Auto energy saving
0~10%
Factory
setting
1
150
0
150
1.0
*
*
04
1440
2.0
0.0
0.0
5.0
150
0
0.5
00
1
0
25
TECORP Electronics
HC1-A User Manual

Item
Special function parameter
Communicatio
n Function
Monitor Parameter
Factory Setting
26
Functio
n code
CD150
CD151
CD152
CD153
CD154
Function
P
I
D
Target Value
Target Value Source
CD155
CD156
CD157
CD159
CD160
CD161
CD162
CD163
CD167
CD168
CD169
PID Upper Limit

PID Lower Limit
Reserved
CD170
CD171
CD172
CD173
CD174
CD175
CD176
Rated current of the inverter

Software version
Fault Record 1
Fault Record 2
Fault Record 3
Fault Record 4
Fault cleared
CD177
Reserved
CD178
Frequency standard of the

inverter
CD179
Manufacture Date
CD180
Sequence Number
CD181
CD250
Reserved
Communication identified NO
Baud rate of communication
Communication agreement

explanation
0.01000.00%
0.1~3600.00s
0.01~10.00s
0.0~100.0%
0:digital operator
1:external terminals
(0- 10V)
0~100%
0~100%
Factory
setting
100%
5.0
*
*
100%
0%
0~250
0~3
05
0
1
0
015
According to the
actual model
According to the
actual model
Note:means no fault
record
00
*
*
*
001001 is fault
cleared
00
Reserved
Display mode select
Rated voltage of the inverter
0:50Hz 1:60Hz
Factory Set
*
*
TECORP Electronics
HC1-A User Manual
9. Detail Explanations of the Function

CD000 Main frequency
Set range:0.00400.00Hz
Unit:0.01Hz
Factory setting:0.00
In the digital operator method. The inverter will run at the setting
value of CD000.During running, users can press the or key to
change the running frequency. During multi-speed running, the main
frequency is the first speed frequency.
In the external terminals method. The inverter will run at the analog
reference frequency decided by the external terminals.
Main frequency is limited by Max.Operating frequency.
Related parameter: CD034, CD076, this setting can be change during
running.
CD001 Max output voltage
Set range:0.1*
Unit:0.1V
Factory setting:220/400V
This value is set according to the rated value on the nameplate of the
motor. Factory setting for 400V class is 400V, 220V class is 220V.
This setting is limited by the voltage grade of the inverter. If the
motor is a little far away from the inverter, users can properly raise its
set value to make up the voltage loss caused by the long distance.
CD002 Base frequency
Unit:0.1Hz
This value must be set according to the rated frequency shown on the
nameplate of the motor. Under most circumstances, please dont change
the set value. If matching a special motor, please change the set value
carefully and properly according to the motor characteristics.
CD003 Voltage at medium frequency
Set range:0.1500.0V
Unit:0.1V
Factory setting:15/27.5
This parameter can set any medium voltage in the V/F curve. If it is
set improperly, it will cause motor over current or deficient torque, or
even an inverter tripping. The set value for 220V class inverter is
15.And the set value for 400V class inverter is 27.5.
This set value is limited by the Max voltage value. When the voltage
at medium frequency increases to certain value, torque boost will be
ineffective. So when adjusting this setting, users should according to the
actual load slowly increases the value to match the starting requirements.
Dont increase it by a big margin.
27
TECORP Electronics
HC1-A User Manual
CD004 Medium frequency set

Unit:0.01Hz
This parameter can set any medium frequency in the V/F curve. If
users set improperly, it will cause motor over current or deficient torque,
or even an inverter tripping. This set value is limited by the base
frequency.
CD005 Voltage at lower frequency
Set range:0.150.0V
Unit:0.1V
Factory setting:8/13.5
This parameter sets the lowest starting voltage in the V/F curve.
This set value for 220V class inverter is 8.And the set value for 400V
class is 13.5.
This set value is limited by the voltage at the highest operating
frequency.
CD006 Lowest frequency set
Unit:0.01Hz
Factory setting:0.50Hz
This parameter set the lowest starting frequency in the V/F curve.
CD007 Highest operating frequency
Unit:0.01Hz
Factory setting:50.00Hz
This parameter set the highest operating frequency of the inverter.
The following curves and set value are for your reference.
V
220
220
220
55
24
15
8
8
0 0.5 2.5
50
25
50
0 0.5 2.5
380
380
380
110
45
27.5
16
13.5
0 0.5 2.5
50
Constant torque curve
28
9
0 0.5
50
20
0 0.5
25
50
Low torque curve
0 0.5 2.5
50
htigh torque curve
TECORP Electronics
HC1-A User Manual
CD008 Frequency upper limit

**
Set range:0.01400.00Hz Unit:0.01Hz Factory setting:50.00Hz
This is set for preventing workers from false operation, avoiding and
mechanical abrasion caused by high speed, or other damage.
CD009 Frequency lower limit
**
Set range:0.00400.00Hz Unit:0.01Hz Factory setting:0..00Hz
This is set for preventing workers from false operation, avoiding
overheat or some other mechanical faults caused by the too low running
frequency.
This set value must be lower than the frequency upper limit.
CD010

**
Set range:01
Unit:1
Factory setting:0
0: invalid
1: valid (which means the other parameters have been locked and
unchangeable)
This function can prevent other personnel from changing your set value.
CD011
Factory setting
Set range:0010
Unit:1
Factory setting:00
If the parameter you have set is improper or abnormal. You can
change it into 08 first to return to the factory setting, and then reset it.
But if CD010 is set for 1, you should unlock the parameter first. Related
parameter: CD010.
CD012 Accel.Time 1
Set range:0.16500.0s
Unit:0.1s
**
Factory setting:10.0/25.0
CD013 Decel.Time 1
Unit:0.1s
**
Factory setting:10.0/25.0
CD014
Accel.Time 2
Unit:0.1s
**
29
TECORP Electronics
CD015
CD016
CD017
CD018
HC1-A User Manual
Decel.Time 2
Unit:0.1s
**
Accel.Time 3
Unit:0.1s
**
Decel.Time 3
Unit:0.1s
**
Accel.Time 4
Unit:0.1s
**
CD019
Decel.Time 4
**
Unit:0.1s
Accelerating Time means time needed for inverter accelerating from
0Hz to 50Hz (See t1 in the diagram)
Decelerating Time means time needed for inverter decelerating from
50Hz to 0Hz (See t2 in the diagram)
F
50Hz
T
t1
t2
HC1-A Series of inverters have 4 accelerating time and 4 decelerating

time.F Accel.time 2.3.4/Decel.time 2.3.4 can be controlled by on/off
signal of external input terminals according to actual needs. In the
inner-controlled multi-speed running,Accel/Decel time can be controlled
by simple PLC.
Generally, the inverter accepts the first accelerating and decelerating
time which has been set by the factory according to actual models as
below. Inverters of 7.5KW or lower: 10 seconds; Inverters from 11KW
to 37KW:25 seconds; Inverters of 55KW or higher: 60 seconds.
Related setting: CD050CD055
CD078
30
TECORP Electronics
CD020CD030
HC1-A User Manual
Reserved
CD031
Starting method select

Set range: 01
Unit: 1
Factory setting: 0
Two starting methods are available for different equipment.
0: means start from the starting frequency.
When CD141 is set for 0.0 (meaning: DC brake is invalid), it starts
at its starting frequency. When CD141 is set for any other parameters, it
will first have a DC braking, and then start from the starting frequency.
Related setting referring to CD040CD140CD141.
1: means start by former speed search
This function can be used in the re-starting of large inertia equipment.
When re-start, the inverter searches the former speed from set. And
when restart, its not necessary to wait for the equipments complete
stop and it can run the executive command right away by doing the
former frequency track and save a lot of time.
Note: When the inverter makes a track starting, it will start tracking
the frequency from its set frequency, and will make it at the highest
speed. When starting, the current will be high, and over current or stall
may appear, so the adjustment for current standard position of speed
search is important.Generally, CD144 should be set around100.The
specific value should be set according to actual situation.
Running Command
Output Frequency
Set frequency
Output Current
CD032 Stop method select
Set range01
Unit1
Factory setting0
Two stop methods are available for meeting different equipment.

0means decelerating to stop
31
TECORP Electronics
HC1-A User Manual
When CD142 is set for 0, DC brake is invalid. When DC brake is

invalid, the inverter will decelerate to the stopping frequency, and
stop output, the motor will have a free running to final stop. When
CD142 is set for any other parameter except 0 (meaning the DC
brake is valid), the inverter will first decelerate to the stopping
frequency, and then stop finally by DC brake.
The DC brake is usually used in high position stopping or for location
control. Special attention should be paid that frequent use of DC
brake will cause the motor overheat.
Related setting referring to CD042CD140CD142
1means free-running to stop
When the inverter receives a stopcommand, it will immediately
stop output and the motor will have a free running to stop. When you
choose the motor free-running stop method, DC brake is invalid.
CD033
Control Mode Select

Set range02
Unit 1
Factory setting0
0 controlled by digital operator

The running command is given by digital operator.
1 controlled by external terminals
The running command is given by external terminals
(multi-function input terminals).
2 controlled by the communications
The running command is given by the communications.
CD034
Command Method Select

Set range02
Unit1
Factory setting0
0 set by digital operator

The running frequency is set by the digital operator.
1 set by external terminals
The running frequency is controlled by the analog singal through
external terminals. The signal type is decided by CD065.Related
introduction refer to CD065-CD070
32
TECORP Electronics
HC1-A User Manual
2 set by the communications

The running frequency is set by serial communications.
CD035
Carrier frequency (Note0-15corresponding to 0-20K Hz

Set range015
Unit1
Factory setting5
The carrier frequency will affect the electromagnetic noise of the

motor, the heating capacity of the inverter and the interference to the
environment. See the following table
Carrier
Electromagnetic
Heating
Interference to
frequency
noise
capacity
the
environment
low
loud
small
little
high
low
large
strong
Carrier frequency corresponding table

Set value
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Carrier
0.7 1 1.5 2 3 4 5 7 8 9 10 11 13 15 17 20
frequency
From the table above, we can see that with a higher carrier frequency,
the electromagnetic noise will be lower, but the interference to other
systems and the heating capacity will be larger. So if the inverter is
working in a space with high temperature, and the motor load is heavy,
carrier frequency should be properly lowered to reduce the heating
capacity.
CD036 Jog frequency
**
Set range0.00400.00
Unit0.01 Factory setting5.00
This parameter can realize the jog function in trial running. It is
controlled only by the external terminals (the multi-function input
terminals).The jog frequency is limited by the Max and Min frequency.
When the jog function is acting, other running commands are not
acceptable. The accelerating time of jog frequency is determined by the
first accelerating time. After relaxing the jog button the inverter will
immediately stop output. When running in jog function, please set the
corresponding multi-function terminal at 07 or 08.The jog function can
33
TECORP Electronics
HC1-A User Manual
only be executed when the machine is in the stop state. It will not be
effective when in running. Related setting refers to CD050-CD055.
CD037
Selection for For/Rev Run

Set range01
Unit1
Factory setting1
0: Forward Run only. Reverse Run is forbidden.

1: Reverse Run is available.
This function is suitable for the motor which cannot allow reverse
rotation. It prevents workers from false operation. When the
reverse rotation is forbidden, the motor will not have reverse
rotation, only forward rotation.
CD038 Stop key valid or not
Set range01
Unit1
Factory setting1
0: the command of STOP is invalid.
1: the command of STOP is valid.
This parameter set is only valid when CD033 is set for l or2.
When the control method is set to external terminals or
communications, the stop key can be chosen to be valid or not.
When you choose it as valid, you can stop the running inverter by
pressing the stop key. When it needs restarting, the former
running signal should be released first.
CD039~CD040 Reserved
CD041 Starting frequency
Set range0.110.0Hz
Unit0.1Hz
Factory setting0.5
Starting frequency is the initial frequency when the inverter begins
to work. If the starting frequency is set for 4.0Hz, the inverter will begin
to run at 4.0Hz, and later between 4Hz and its Max operation frequency.
(The actual Max operation frequency is confined to the lower/upper
limit of the frequency).
Related setting refer to: CD031, CD140, CD141
CD042 Stopping frequency
Set range0.110.0 Hz
Unit0.1Hz
Factory setting0.5
When the inverter receives a stop command, it will immediately
decelerate to the stopping frequency, stop output or start DC brake to a
final stop.
34
TECORP Electronics
HC1-A User Manual
If CD142 is set for 0, the inverter will stop output DC brake is

invalid when it decelerate to the stopping frequency
If CD142 is set for any other parameter except 0, DC brake is valid;
the inverter will stop by DC braking. When it decelerate to the stopping
frequency.
Related setting refer to CD032CD140CD142
CD043 Torque Boost
Set range0.120.0%
Unit0.1%
Factory setting2.0
This parameter setting can make the inverter output extra voltage
automatically when in running and get a high torque to compensate for
the deficit torque when the motor is running in low frequency. The
torque boost should not be
too large. It should be set
V
gradually from the low point
100%
to the high point according to
actual situations. If the boost
is insufficient it will cause
the motors torque
insufficient at low frequency. Torque Boost
But if the boost is too large, it
F
will cause too large torque, which will give impulse to the machinery,
and even cause inverter to trip when being serious.
CD044 Skip frequency 1
**
Set range0.00400.00 Hz
Unit0.01Hz Factory setting0.0
CD047 Skip frequency range
Unit0.01Hz
**
Factory setting0.5
F
CD046
CD045
CD044
Jump point
CD047
CD047
In order to avoid meeting the mechanical resonance point, these three

35
TECORP Electronics
HC1-A User Manual
skip points are set. When CD047is set for 0, all the set skip
frequencies are invalid; the actual skip frequency range is twice of the
setting value of CD047.
Shown as above.
CD048 CD049
Reserved
CD050 Multi-function Input Terminal 1 (FOR) Factory setting:02

CD051 Multi-function Input Terminal 2 (REVFactory setting: 03
CD052 Multi-function Input Terminal 3 (RSTFactory setting: 10
CD053 Multi-function Input Terminal 4 (SPHFactory setting: 17
CD054 Multi-function Input Terminal 5 (SPMFactory setting: 18
CD055 Multi-function Input Terminal 6 (SPLFactory setting: 19
Set range0032
Unit1
ITEM
NAME
00
Terminal Invalid
01
Run
02
03
04
05
FOR
REV
STOP
FOR/REV
06
07
08
09
JOG
JOG FOR
JOG REV
Emergency stop
10
RST
11
Reserved
12
Overheat
36
DESCRIPTIONE
Empty terminal, avoid false
operation.
Control the run and stop of the
inverter, and also used to make up
multiple control methods combining
with other terminals.
Forward run.
Reverse run.
Stop.
Forward run, Reverse run shift
switch.
Jog.
Jog forward rotation.
Jog reverse rotation.
The inverter would stop immediately
when there was emergency.
The inverter can be reset when the
fault is cleared.
Using this function to protect heat
TECORP Electronics
HC1-A User Manual
sink and motor from overheat.

13-16
Reserved
17
High speed
18
Medium speed
19
Low speed
20
Multi-speed 1
21
Multi-speed 2
22
Multi-speed 3
23
ACCEL/DECEL
time select 1
ACCEL/DECEL
time select 2
UP
DOWN
These three speeds provide three

different running patterns, and they
are determined by the second, the
third, and the forth frequency
These three speeds can provide seven
different speed
The acceleration and deceleration

time can be selected by these
terminals, altogether 4 patterns are
24
available
Every single press on these keys will
25
make the inverter frequency go up or
26
down for one unit, while if either key
is kept pressing, the frequency value
will swiftly go up and down
continuously. If the power recovers
after loss, the frequency set by
UP/DOWN key will not exist any
more
27
Counter
This terminal can receive pulse signal
(<250Hz) and count the number.
28
Counter Reset
Pressing this key will clean up the
former display data and reset the
CD00, ready for the next counting.
29
Drafting
This function is special for chemical
fiber instrument.
30
PID
This terminal is used to begin the PID
function.
AThree-lines system connection using RUN. STOP .DCM
STOP RUN
FOR
REV
DCM
1) Using multi-function terminals FOR and

REV
2) Parameter setting: CD033=1
CD050=01
37
TECORP Electronics
HC1-A User Manual
CD051=04
BUsing RUN.DCM.F/R to start,stop,forward and reverse run and
reverse rotation.
1) Using multi-function terminals FOR and REV.
K
FOR
2) Parameter setting: CD033=1
K
CD050=01
REV
CD051=05
DCM
K2 open for FOR run; K2 closed for REV run.
1
CIntroduction of the acceleration or deceleration time select One and

Two.
1. This function is only valid when CD076 is set for0.1or 2 .When in
disturbance and inner control multi-control speed method it is invalid.
2. Any two multi-function input terminals can make up 4 patterns of
acceleration or deceleration time.
3. Take the SPH.SPM terminals as an example. When CD053 for SPH is
set for 23, and CD054 for SPM is set for 24, the four acceleration or
deceleration patterns are shown in the following table.
SPH
SPM
Results
terminal
terminal
OFF
OFF
The first acceleration or deceleration time
ON
OFF
The second acceleration or deceleration time
OFF
ON
The third acceleration or deceleration time
ON
ON
The fourth acceleration or deceleration time
DIntroduction of high speed, medium speed and low speed terminals
F
High speed
Medium speed
Low speed
Main frequency
RUN C ommand
Low speed
Medium speed
High speed
38
TECORP Electronics
HC1-A User Manual
RUN SPL
terminal
ON OFF
SPM
SPH
Results
terminal terminal
OFF
OFF
Main speed and the run frequency
are determined by CD000.
ON ON
OFF
OFF
Low speed and the run frequency
ON ON/OFF ON
OFF
Medium speed and the run
frequency are determined by
CD081.
ON ON/OFF ON/OFF ON
High speed and the run frequency
Note1This function is only valid when CD076 is set for1(i.e. in
external control four speed)
2The frequency of low speed, medium speed and high speed
are determined by the second,third,fourth frequencies.
3The acceleration or deceleration time is controlled by the
acceleration or deceleration selection terminals.
4When multiple signals are received, it will have the priority
from the high to the low.
EUP/DOWN terminals
F
Max operation frequency
Set frequency
Frequency Lower limit
Up command
Down Command
39
TECORP Electronics
UP
ON
OFF
ON
HC1-A User Manual
DOWN
OFF
ON
ON
RESULTS
Frequency up
Frequency down
Neither up nor down
Note1UP/DOWN functions are only valid when the command

method is set by digital operator(i.e. CD043 is set for 0)
2If the UP terminal is closed, the inverter output frequency
will gradually increase.
3If the DOWN terminals is closed, the inverter output
frequency will gradually decrease.
4If the UP and DOWN terminals are closed at the same time,
the frequency will not increase nor decrease.
5When the frequency reaches its highest operation frequency,
it will not go up any more.
6When the frequency reaches its lowest operation frequency
or its lower limit, it will not go down any further.
7If a momentary power loss occurs, the former frequency will
not be remembered by the inverter and it will recover to its
original CD000.
8Using UP/DOWN functions, thekeys on the digital
operator are valid. After the data value is changed, users
should press the enter key, and then the inverter will
receive the new setting. And meanwhile this value will be
stored into CD000.If power loss occurs; this data value will
not be lost.
9Press the UP or DOWN terminals continuously, the
frequency will swiftly go up or down.
(10)If data value is changed through UP and DOWM
terminals ,by setting CD072,users can decide whether to
forever modify and remember the new value or hot.(Refer to
CD072)
40
TECORP Electronics
HC1-A User Manual
FMulti speed 1.2.3.

This function is only valid when CD076 is set for 2.Related
introduction refer to CD076.
G Counting
C00
C00
cn
t1
t2
Counting Arrival
Counting Reset
Note1Trigger signal width mustnt be narrow than 2msect1t2

2msec
(2) When the counter arrives at its setting value, the
corresponding multi-function output contact act.
3The counter cannot do a new counting until it is reset.
4When the counter arrives at its Max point 65535 it will not
display the correct number with the number still going up.
CD056 Multi-function Output OneDRV terminal
Factory setting 01 **
CD057 Multi-function Output TwoUPF terminal Factory setting 05
CD058 Multi-function Output Three - FA
FB
FC terminal Factory setting 02
CD059 Multi-function Output Four -KAKB terminal Factory setting 00
Setting range0032
Unit1
00: no function
01: running
02: fault signal
This is only for preventing false operation.

The contact will act when the inverter is in
running or receiving running command
signals.
The contact will act when the inverter
detected fault.
41
TECORP Electronics
03: zero speed
HC1-A User Manual
when the inverter output frequency is

lower than its starting frequency.
04: DC brake indication
The contact will act when the inverter is in
DC braking condition.
05: Up to set frequency
The contact will act when the output
frequency has reached the set frequency.
06: Up to desired frequency1 The contact will act when the output
frequency has reached the desired
frequency (CD061).
07: Up to desired frequency2 The contact will act when the output
frequency has reached the desired
frequency (CD062).
08: on accelerating
The contact will act when the inverter is
accelerating.
09: on decelerating
The contact will act when the inverter is
decelerating.
10: overload alarm
detected overload fault.
11: Motor overload alarm
detected motor overload fault.
12: Over torque alarm
detected over torque.
13: Under voltage alarm
detected under voltage fault.
14: Single stage end
The contact will act when the inverter has
finished a single stage in its program
running.
15: Whole process end
The contact will act when the inverter has
finished the whole process in its program
running.
16: Counting arrival
The contact will act when the internal
counter has reached the setting value
(CD064).
27: Drafting arrival
This contact will act when drafting is
42
TECORP Electronics
28: PID Lower alarm
29: PID Upper limits alarm
30: Fan run
32: Braking resistor
HC1-A User Manual
finished, when the inverter stops it will

auto reset.
This contact will act when the PID
feedback value is lower than the lower
limit (CD156 setting).
This contact will act when the PID
feedback value is larger than the upper
limit (CD155 setting).
When the inverter is working in high
temperature or in running, this contact will
act.
When the inverter is running and the DC
voltage reaches its brake voltage, this
contact will act.
CD060
Multi-function output 5
**
Set range:07
Unit:1
Factory setting:1
Function: Analog frequency output terminal, output 0-10V.It can be
Joined together with CD071 for external monitoring if connected to a
Frequency meter with a measuring range of 10V or below.
0: invalid
1: output frequency 2: output current (010V)
3: DC voltage (010V)
4: output voltage (010V)
567:invalid
CD061
Up to desired frequency 1 setting
**
CD062
Up to desired frequency 2 setting
Set range:0.00400.00Hz Unit:0.01Hz
CD063
Up to frequency setting detection width
**
Set range:0.0010.00Hz Unit:0.01Hz Factory setting:0.50
When the output frequency is in the range of up to frequency setting
detection, the corresponding multi-function output will act. If it is not in
the range, no contact will begin to act.
43
TECORP Electronics
HC1-A User Manual
F
Frequency agreed
2*CD063
Frequency agreed
CD064
Counter set
**
Set range065500
Unit1 Factory setting0
The counter takes the multi-function external terminal as its contact
Terminal. When the counting value reaches the set value of CD064, the
corresponding multi-function output contact will act. The counter can go
on for a new counting only after the former numerical value is cleared
Up and the counter gets a reset. The trigger signal can be sent by
Proximity switch and photoelectric switch,etc.
CD065
Analog input select

Set range04
Unit:1
Factory setting0
00~10V
10~5V
20~20mA
34~20mA
4both 0-10V and 4-20mA
This parameter setting can meet different analog input signals.
When CD065=4,output frequency=1/2(U/Umax+I/Imax)50Hz
U: Analog Voltage
Umax: Max Analog Voltage
I: Analog Current
Imax: ax Analog Current
When the analog value is +10V and 20mA, the output frequency is
50Hz.
CD066 Lower analog frequency set point
Unit0.01 Hz
Factory setting0.00
CD067
44
Lower analog frequency bias direction

Set range01
Unit:1
Factory setting0
0Positive direction
TECORP Electronics
HC1-A User Manual
1Negative direction
Bias direction means commands for FOR or REV run. Positive bias
means FOR run; negative bias means REV run; Related setting, refer to
CD070.
CD068
Higher analog frequency set point
Set range0.00400.00 Hz Unit0.01Hz Factory setting50.00
CD069
Higher analog frequency bias direction

Set range01
Unit:1
Factory setting0
0Positive direction
1Negative direction
Bias direction means commands for FOR or REV run. Positive bias
means FOR run; negative bias means REV run; Related setting, refer to
CD070.
CD070
Negative bias reverse select

Set range01
Unit:1
Factory setting0
0Negative bias reverse is invalid.
1Negative bias reverse is valid.
This parameter group can set the measuring range and zero point of the
external. Analog terminals and also can build any curve to control the
motor running.
For example
F
Reverse rotation area
0V
4mA
50Hz
Forward rotation area
5V
10V
12mA
20mA
settingCD066=50
CD067=1
CD068=50
CD069=0
CD070=1
F
50
0
4mA
10V
20mA
Setting: CD066=50
CD067=0
CD068=0
CD069=0
CD070=1
45
TECORP Electronics
HC1-A User Manual
Setting: CD066=10
CD067=1
CD068=40
CD069=0
CD070=1
40
0
4
10v
20mA
10
40
0v
4mA
10
2v
4.8mA
10v
20mA
Setting: CD066=10
CD067=1
CD068=40
CD069=0
CD070=0
CD071 Analog output gain

**
Set range0.0100.0%
Unit:0.1%
Factory setting100.0
This setting can adjust the output voltage of the six multi-function
output terminals to adapt to the frequency meters with different
measuring ranges and also it can help adjust the frequency meters
according to this parameter.
CD072
UP /DOWN Function Select
**
Set range:01
Unit:1
Factory setting:1
0: Recorded
1: non-recorded
This setting can decide whether the new setting frequency modified
by up/down function will be recorded or not. If CD072 is set for 0, then
the new value will be recorded and when the inverter is re-started, the
new data will be valid. If CD072 is set for 1, then any change of the
frequency will be missed and the parameters shown on the display
screen is their former settings after restarting the inverter.
46
TECORP Electronics
HC1-A User Manual
CD073~CD075
Reserved
CD076
PLC mode select

Set range: 04
Unit: 1
Factory setting: 0
0: normal running
i.e. run by normal control method
1: external control four speed (related introduction refer to
CD050-055)
2: external control multi speed
F
Main frequency
Multi speed1
Multi speed2
Multi speed3
Multi-function Terminal
Multi Multi Multi
speed 1 speed 2 speed 3
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
ON
Result
Main frequency and the frequency are determined
by CD00 or external analog input.
Speed 1 and the frequency are determined by
CD080.
CD081.
CD082.
CD083.
CD084.
47
TECORP Electronics
OFF
ON
ON
ON
HC1-A User Manual

CD085.
ON
CD086.
ON
NoteOnly when the multi-function input terminals are set to be multi

speed 1,2,3 and CD076 is set for 2.The function of external
control eight speed running method can be realized.
Seven speeds can be made up by different combinations of
Multi speed 1,2,3,plus the main frequency. Thus eight speeds
are available.
The frequencies of speed1speed7are determined by
CD080CD086.
Every single acceleration or deceleration time is determined by
external multi-function terminals.
Every single program running direction is determined by
external multi-function terminals.
The main frequency is decided by two methods. One is set by
CD000; the other is set by external analog input signal. When
CD034 is set for 1, the main frequency is set by the external
analog input signal. Rated setting, refer to CD000, CD034,
CD080094.
3Disturbance(the function of cross traverse)
This parameter is set particularly for the realization of cross
traverse in the chemical fibre, printing and dyeing industry. In running,
any other command will not be accepted except for stop, external fault
and emergency stop.
F
CD000
CD086
CD087
CD088
CD086
CD080
48
TECORP Electronics
Note
HC1-A User Manual
Every break frequency is determined by CD000 and CD080.

Skip frequency is determined by CD086.
Running time is controlled by timer CD087,CD088.
Related setting: refer to CD000,CD080088.
4Inner control multi speed

F
CD087 CD088
CD089 CD090
CD091 CD092 CD093 CD094
Note Main speed and seven-step speed make up eight-step speed.

Every single acceleration or deceleration time is set by PLC
acceleration or deceleration time (CD079).Related introduction
refer to CD079.
Running time is controlled by timer CD087-CD094.The timer
should be set for 0 for idle control step.
The running direction of every single step is set by CD078.
When in inner control multi speed running, the running time and
direction are both set by inner paremeters.The external
command for time switch or FOR/REV rotation switch is
invalid.
5. Drafting
This setting is especially for the realization of constant speed for giving
and receiving the rolled string.
F
CD080
CD081
CD000
T
Multi-function input
Multi-function output
49
TECORP Electronics
HC1-A User Manual
Note:Drafting is energized by the external multi-function terminal.

When executing the drafting is running action, the running time
is:T=CD08710
When drafting is finished, the inverter at a constant
speed(CD081),and at the same time, the corresponding
multi-function output contact is energized until a stop
command is received.
CD077
Auto PLC Select

Set range: 03
Unit: 1
Factory setting: 0
0: stop after running one circle

1: circulating running
2: stop after auto running one circle (with stop interval)
3: auto circulating running (with stop interval).
This parameter setting is valid only when CD076 is set for 4.
Related introduction refer to CD000, CD076, CD078~CD094,
Note: 0: stop after running one circle the inverter will start to execute
the circulating running command at its
inner parameter set value and stop after running one circle. Only when
the inverter receives a new running command, will it start to run again.
1. Circulating running
The inverter will start to have a circulating running in its set order at
its inner parameter set value of step frequency and running time when
the inverter receives the running command. Any other command will not
be accepted in the circulating running, except for stop, external fault,
and emergency stopped.
50
TECORP Electronics
Manual
HC1-A User
2Stop after auto running one circle(with stop interval)

F
CD081
CD085
CD082
CD000
CD086
CD083
CD087 CD088
CD089
CD090 CD091 CD092 CD093
CD094
CD084
CD080
Note
1) When the auto running command is received, the inverter begin to
run at its parameter set value .When every stage changes, the
inverter will first stop and then restart again. The inverter will
automatically stop after running for one circle. Only when a new
running command is received, will the inverter begin to run again.
2) The frequency for different steps is set by CD000, CD080-CD086.
3) The running time for different steps is set by CD087-CD094.
4) The running direction is set by CD078.
3Auto circulating running(with stop interval)

F
CD086
CD084
CD082
CD085
CD083
CD000
CD087 CD088 CD089
CD090
CD000
CD091 CD092 CD093 CD094 CD087

CD080
CD084
CD084
Note1When the inverter receives the auto running command, it begin

to run in its parameter set order. When every stage changes, it
will first stop and then restart, and go on running till the auto
running command turns to OFF.
51
TECORP Electronics
Manual
HC1-A User
2) When a single step is finished, the corresponding

multi-function output contact will act.
3When a process is finished, the corresponding multi-function
output contact will act.
4Output pulse width is 20ms.
CD078
PLC running direction
Set range0255
Unit1
Factory setting0
This parameter setting is only valid, when CD076 is set for 4.
This parameter will determine the running directions of different
frequency steps of CD080~CD086.CD00 in PLC running.
The running direction is set by the binary 8 BIT method, and then be
changed into decimal system to set this parameter. See the following
diagram.
Bit07
7 6 5 4 3 2 1 0
0 1 0 0 1 0 1 0
Parameter value 01001010 to be changed into decimal system, i.e.

126+123+121=64+8+2=74
So the parameter of CD078 should be 74.
CD079
PLC Accel./Decel.time
Set range0~65535
Unit1
Factory setting0
This parameter setting valid only when CD076 is set for 4.

This parameter setting determines the acceleration or deceleration time
of the inner control multi-step speed and every signal step speed. It is set
as follows:
52
TECORP Electronics
Manual
HC1-A User
1 Binary 2BIT method

BIT BIT Acceleration or Deceleration Time
1
0
0
0
The first acceleration or deceleration time CD012,CD013
0
1
The second acceleration or deceleration time
CD014,CD015
1
0
The third acceleration or deceleration time CD016,CD017
1
1
The fourth acceleration or deceleration time
CD018,CD019
2 Binary 16BIT method
Speed8 Speed7 Speed6 Speed5 Speed4 Speed3 Speed2 Speed1
t8
t7
t6
t5
t4
t3
t2
t1
0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 1
t1 choose the fourth acceleration or deceleration time
t2 choose the first acceleration or deceleration time
t3 choose the third acceleration or deceleration time
Set parameter
t4 choose the second acceleration or deceleration time
120+121+125+126=99
So CD079 should be set 99

CD080
CD081
CD082
CD083
CD084
CD085
CD086
The second frequency setting

The third frequency setting
The fourth frequency setting
The fifth frequency setting
The sixth frequency setting
The seventh frequency setting
The eighth frequency setting
Factory setting
Factory setting
Factory setting
Factory setting
Factory setting
Factory setting
Factory setting
Unit0.01 Hz
15**
20
25
30
35
40
0.5
This setting combining the multi-function input terminal can form

external control 4-step speed, external control multi-step speed,and inner
control multi-step speed.
53
TECORP Electronics
Manual
HC1-A User
Related setting: refer to CD076, CD087~CD094.

CD087
Timer one
CD088
Timer two
CD089
Timer three
CD090
Timer four
CD091
Timer five
CD092
Timer six
CD093
Timer seven
CD094
Timer eight
Set range0.06500.0S
Factory setting
Factory setting
Factory setting
Factory setting
Factory setting
Factory setting
Factory setting
Factory setting
Unit0.1S
10.0**
10.0
0.0
0.0
0.0
0.0
0.0
0.0
This setting is to determine the running time of executing drafting

function and inner multi-step speed running.
Related setting: refer to CD076, CD080~CD088.
CD095CD119
CD120
Reserved

Set range01
Unit:1
Factory setting1
0The function of stall prevention is invalid.

1The function is valid.
When the inverter is in decelerating, because of the effect of load,
the motor will produce a return energy to the inverter and cause the DC
side voltage of the inverter increase. So when the function of over
voltage stall prevention is set valid and the DC voltage of the inverter
becomes too high, the inverter will stop decelerating till the DC bus
voltage decreases to allowed value, then the inverter will go on to
execute deceleration and of course the deceleration time will be longer.
CD121
Stall prevention level during acceleration
Set range0200%
Unit1%
Factory setting150
When the inverter is in accelerating, because of over load or too
short acceleration time, the output current of the inverter will go up
54
TECORP Electronics
Manual
HC1-A User
quickly and exceed the rated value level. When this happens, the
inverter will stop accelerating, until the current returns under its rated
value, will the inverter go on to accelerate.
100% current is the motor rated current. If this parameter is set for0,
stall prevention function is invalid.
CD122
Stall prevention level during running

Set range0200%
Unit1%
Factory setting
0
When the inverter is in constant speed running, because of the
change of load and some other reasons, the current will go up. When the
current exceeds its rated value, the inverter will lower the output
frequency. When the output current returns to its normal range the
inverter will accelerate to its set frequency again.
stall prevention standard level

current
output frequency
100% current is the motor rated current.

If this parameter is set for 0, stall prevention function is invalid.
CD123
Stall prevention level during decelerating

Set range: 0200%
Unit1
Factory setting150
Related introduction refer to CD120
current
output frequency
T
55
TECORP Electronics
Manual
HC1-A User
100% current is the motor rated current.

CD124
CD125
Reserved
Over torque detection level
Set range0200%
Unit1%
Factory setting
0
When the output current exceeds the over torque detection level and
also exceeds half of the over torque detection time (factory setting: 1.0s),
the over torque detection will begin to work, and the corresponding
multi-function contact will act. When it exceeds the set time value, the
inverter will turn into self-protection. But when this parameter is set for
0, the over torque detection will be invalid.
CD126
Over torque detection time

Set range: 0.120.0s
Unit: 0.1s
Factory setting: 1.0
When the inverter detects that the output current has exceeded the
rated current, the inverter begins to calculate the over torque time. When
the over torque time has exceeded half of the over torque detection time,
the corresponding multi-function output contact will act, the over torque
warning will be produced, while the inverter will continue running.
When the over torque time has exceeded the set detection time (set by
CD126), the inverter will turn into self-protection, display the fault
signal and stop output.
Related introduction refer to CD125.
CD127CD129
CD130
56
Reserved
Rated voltage
Unit: 0.1V
Factory setting:*
TECORP Electronics
Manual
HC1-A User
Set according to the rated voltage shown on the nameplate of the

motor .The factory setting for 230-v class inverters is 220, for 440-v
class inverters is380.
CD131
Rated current
Unit: 0.1A
Factory setting:*
Set according to the rated current shown on the nameplate of the

motor. With this parameter users can limit the inverter output current,
pervert overc urrent,and protect the motor.If the motor current exceeds
this set value, The inverters will turn into self-protection.
CD132
Motor Poles
Set range0210
Unit:1
Factory setting04
This parameter should be set according to the motor nameplate.

CD133
Rated rotational speed
Set range09999
Unit:1r/min
Factory setting1440
This parameter should be set according to the actual motor rotation

speed. The display value is the same as this parameter. It can be used
as monitoring parameter which brings convenience for users to
monitor the running state. This parameter set value is corresponding
to the rotational speed at 50Hz.
CD134~CD139
Reserved
CD140
DC braking level
Set range0.020.0%
Unit0.1%
Factory setting2.0
This setting determines the DC brake voltage of the motor when

starting or stopping. Adjustments of this parameter can result in different
brake voltage values. When adjustments are being done, users must
increase the parameter value slowly until it gets enough brake torque.
100% voltage is the output voltage at Max frequency.
57
TECORP Electronics
Manual
HC1-A User
CD141
DC braking time at starting
Set range0.025.0S
Unit0.1S
Factory setting0.0
This setting determines the DC

braking lasting time during DC
brake at starting.
If it is set for 0 it means DC
CD041
brake is invalid.
T
The DC brake at starting is usually
CD141
used in the cases in which the load
is movable in the stop state.
Such as cooling fan and some other machines. Because of the load, the
motor is always in a free running state, with an uncertain running
direction.
Users can first start the DC brake before starting the inverter to prevent
the inverter from tripping.
This setting is valid only when CD131 is set for 0.Related
introduction refer to CD031,CD140.
F
CD142
Set range0.025.0
Unit0.1S
F
CD042
T
CD142
58
Factory setting0.0
Note:This setting determines the DC

braking time at stopping when it is
not set for 0.The DC brake at
stopping is usually used in high
position shutdown or for location
control. This setting is valid only
when CD032 is set for 0.Related
introduction refer to CD032, CD042,
CD140.
TECORP Electronics
Manual
CD143
Speed search time

Set range0.120.0S
HC1-A User
Unit0.1S
Factory setting2.0
This parameter is set as speed search time when the inverter

restarts by the speed search method after clearing the external faults or a
momentary power less.For the starting and stopping of some large
inertia load,because of its large inertia,if users restart the machine after
its complete stop,it will waste much time.But using the speed search
function,things are different.You neednt wait for the machines fully
stop,the inverter will make a frequency tracking from high to low at its
set frequency.After tracking the inverter will continue to accelerate to
reach the set frequency.
CD144 Speed search current level
Set range0200%
Unit1%
Factory setting150
When the inverter is making a speed search, If the output current is

higher than this standard level, the inverter will decrease the frequency
to make the current return to its normal range and then execute the
command of speed search again.
CD145
Restarting select after a momentary power loss

Set range01
Unit:1
Factory setting0
0 invalid
no auto restarting after a momentary power loss
1restart by speed search
Related introduction refer to CD143
CD146
Momentary power loss ride through time

Set range0.15.0S
Unit0.1S
Factory setting0.5
This setting determines the longest time allowable for momentary power
loss.If it exceeds the allowable time; the inverter will still be in a stop
state after the power recovery occurs. If users want to restart the inverter,
you need to follow the normal starting steps again.
CD147
Number of auto restarting attempt

Set range0010
Unit1
Factory setting00
When meeting abnormal situations such as over current, over

59
TECORP Electronics
Manual
HC1-A User
voltage, etc, the inverter will have an auto reset and restart itself. If the
starting method is set as normal starting, the inverter will start in the
normal method. If the starting method is set as speed search starting, the
inverter will start in the speed search method. After restarting, if meeting
no new abnormal situation after 60 second, the parameter will return
to its set value again. If meeting new abnormal situations again and
again, and reaching the Number of auto restarting attempt, the inverter
will stop output. Only after reset can the inverter restart again. If CD147
is set for 0, the inverter will not have auto reset and restart function in
abnormal situations.
CD148
Auto voltage regulation

Set range01
Factory setting1
0invalid
1valid
Under the situation of unstable power supply, if the voltage is too
high and the motor is running at a higher voltage than its rated, this will
cause the motor temperature to increase, the insulation to be destroyed,
and output torque to be unstable. The auto voltage regulation function
can keep the output voltage within the rated motor voltage.
When this function is set for 0 there will be fluctuation of the
output voltage.
CD149
Auto energy saving
Set range020%
Unit 1%
Factory setting 0
If this parameter is set for 0, the energy saving function is
invalid. In auto energy saving, it will run at its full voltage when
accelerating or decelerating; when in constant running it will run at the
best voltage value which is auto calculated by the load power and thus
reach the purpose of energy saving.
The Max energy saving rate can
reach30% But for those
have
frequent load changes or are almost
full loaded, this function is not
suitable.
Output voltage
100%
70%
F
60
TECORP Electronics
Manual
HC1-A User
CD150 Proportional Constant: P

**
Set range: 0.0~1000.0%
Unit: 0.1%
Factory setting: 100%
This setting determines the error value gain. If I=0, D=0, it is only for
proportion control.
CD151 Integral Time: I
**
Set range: 0.1~3600.0s
Unit: 0.1s
Factory setting: 5.0s
This setting determines the reaction speed for PID.
The larger the I value is the slower the reaction speed is. But if the
integral time value is set too small, it will cause vibration.
CD152 Differential Time:D
**
Set range: 0.01~10.00s
Unit: 0.01s
Factory setting: 0
This setting determines the depression operation of PID.
The larger the D value is, the more obvious the depression operation
is. When D is set for 0, it means this function invalid.
CD153
Target Value
**
Set range:0~100.0%
Unit:1%
Factory setting:*
The target value can be set through external voltage signal or the
digital operator.100% target value is corresponding to the frequency
when the analog voltage is 10V.
PID closed-loop control is usually used in the control of processed of
no fast physical quantity changes, such as pressure control, temperature
control,etc.The feedback signal is usually taken from temperature, or
pressure translator etc.When under PID control, the feedback signal
input path is the analog current signal 4-20mA.
PID closed-loop control is valid only when the multi-function inputs
PID are open.
PID Control Diagram:
Target
value
CD150
CD151
+
VVVF
+
CD152
D
61
Feedback
TECORP Electronics
Manual
HC1-A User
General operating methods of PID control:

(1) Choose the correct translator (with output specification of standard
current signal 4-20mA)
(2) Set the right target value.
(3) If the output doesnt have oscillation, increase the proportional
constant (P);
(4)If the output doesnt have oscillation, decrease the integral time (Ti);
(5) If the output doesnt have oscillation, increase the differential time
(Td);
(6) Application Examples as follows:
1. Decrease the Over
Before regulating
Output
Output
a. decrease the
Target value
differential time (D)
After regulating
b. increase the integral
time (I)
Time
Output
Before regulating
Target value
After regulating
Time
2. Decrease the
oscillation
a. decrease the
differential time (D) or
set it for 0
b. decrease the
proportional constant
(P)
CD154
PID Target Value Source

**
Set range: 0~1
Unit: 1
Factory setting: 0
The target value can be set through the digital operator and the external
analog signals. The external analog signal is given by 0-10V signal or
Variable Resistor.
When CD154=0, the target value of PID is set by CD153.
62
TECORP Electronics
Manual
HC1-A User
When CD154=1, the target value of PID is set by external analog

signal 0-10V (corresponding 0-100%), the setting of CD153 is invalid.
CD155
PID Upper Limit

**
Set range: 0~100 %
Factory setting: 100%
When the PID feedback value is higher than the setting of CD155, the
corresponding multi-function output contact will be energized. While
the machine will not stop working.
CD156
PID Lower Limit

**
Set range: 0~100%
Factory setting: 0%
When the PID feedback value is lower than the setting for CD156, the
corresponding multi-function output contact will be energized. While
the machine will not stop working.
CD157~CD159
Reserved
CD160
Communication identified no
Set range: 00~250
NO.
Factory setting: 00
When the inverter is set to be RS-485 Communication control. The
inverter will be set an individual identified No.
00: no communication function
01~250: inverter individual identified No.
CD161
Baud rate of communication

Set range: 0~3
Unit: 1
Factory setting: 1
0: 4800 bits/second
1: 9600 bits/second
2: 19200 bits/second
3: 38400 bits/second
CD162
Communication Data Method

Set range: 0~5
Unit: 1
0: 8N1 For ASC
1: 8E1 For ASC
3: 8N1 For RTU
4: 8E1 For RTU
Factory setting: 0
2: 8O1 For ASC
5: 8O1 For RTU
63
TECORP Electronics
Manual
HC1-A User
HC1 MODBUS communication agreement

When we use inverter with RS485 communication interface each of
them must be set an individual address Thus the computer can use this
address to control the inverter.
1: communication agreement has two modes
1) RTU mode (Remote Terminal Unit)
2) ASC mode( America Standard Code for information interchange)
Information of code.
RTU mode:
Each of 8-BIT data is composed of two 4-BIT data, for example: 64H
ASC mode:
Each of 8-BIT data is composed of two ASCbyte, for example:
64H(hexadecimal)is composed of ASCbyte64,included6(36H)
and 4(34H).
Character symbol
ASCII
30H
31H
32H
33H
34H
35H
36H
37H
2: Communication data mode

Character symbol
ASCII
38H
39H
41H
42H
43H
44H
45H
46H
3: Communication data format

3.1 ASC mode
Communication data format
STX
ADDR FUNC LEN DATE(n-1)DARA0 LRC END
:
CR0DH
(3AH)
LF0AH
1) STX: start data :( 3AH)
2)ADDR communication address,8-BIT data is composed of two ASC
byte.
00: broadcast for all inverter
01 250: the address of the inverter.
3) FUNC:function code,8-BIT data is composed of two ASC byte.
01: read the data of function code
02: write the data of function code
03: control command
64
TECORP Electronics
Manual
HC1-A User
04: read status data

05: write inverter frequency data
06: keep
07: keep
08: loop test
a.Read function code data
format:
ADDR 01 LEN FUNC DATA
ADDR=0 means no answer
ADDR=1-250 Means having answer from inverter with this address
When the inverter reply normally the format is as below.
ADDR 01 LEN FUNC DATA
If DATA is one word, the LEN=3
If DATA is one byte, the LEN=2
When the inverter has not gotten this function code. Or the reply is
ineffective, the format is as below
ADDR 81H 01FUNC.
b.Write function code data
format: 02 LEN
ADDR FUNC DATA
ADDR=0 for broadcast, it would write to all inverters, but no reply
ADDR=1-250 could set data and have answer from the inverter with
this address.
When the inverter has not gotten this function code. Or the reply is
ineffective, the format is as below
ADDR 82H 01 FUNC.
c.Control command
format:LEN
ADDR 03 CNTR
ADDR=0 for broadcast, it would write to all inverters, but no reply
ADDR=1-250 could set data and have answer from the inverter with
this address.
65
TECORP Electronics
Manual
HC1-A User
CNTR format
7
6
Jog REV
Jog
FOR/REN
STOP
REV
FOR
Run
Jog FOR
When inverter reply normal, format as follows

ADDR 03H 01 CNST
CNST format
7
Start
DC Brake
FOR/REV
joggin
running
FOR/REV
Jog
Run
By speed search
When the command is in correct or the reply is ineffective, the format

is as below ADDR 83H 01 CNST.
d.Read status data
format:
ADDR 04 01 CFG
ADDR=0 for broadcast, it would write to all inverters but no reply.
ADDR=1-250 would have reply from inverter with this address
CFG=0 reply all data
CFG=1-8 reply single data
CFG data is defined as following
1:Set F
Set frequency
2: Out F Output frequency
3: Out A Output current
4: Rot T Rotational speed
5: DCV
DC voltage
6:ACV
Output AC voltage
7:Cont
Count
8:Tmp
Temperature
4) LEN: data length
it means the length of D (n-1) - D (0)
If the data is one word the LEN is 3
If the data is one byte the LEN is 2
5) DATA: data content
each of 8-BIT data is composed of two ASC byte, it have fifty
ASC at most.
66
TECORP Electronics
Manual
HC1-A User
6) LRC: longitudinal redundancy check

The method to get LRC is that add all the data from ADDR to the last
byte of DATA, if the result is more than 256,then the result subtract 256
until the result is less then 256,then 100H subtract the result get LRC.
7) For example: write 30.00Hz to inverter with the address 01.
STX
ADDR
:
0 1
3AH 30H31H
FUNC
0 2
30H32H
LEN
0 3
30H33H
DATA
0 0 0 B B 8
30H30H30H42H42H38H
LRC
3 7
33H37H
END
CR LF
0DH0AH
Calculate LRC:
01H+02H+03H+00H+0BH+B8H=C9H,
100H-C9H=37H
so the sent data is following
3AH 30H 31H 30H 32H 30H 33H 30H 30H 30H 42H 42H 38H
33H 37H 0DH 0AH
3.2 RTU mode
QUIET
50ms
ADDR
FUNC
LEN
D(n-1)~D0
CRC
QUIET
50ms
1) QUIET: the time of no data is more than 50ms

2) ADDR: communication address, 8 bit data.
3) FUNC: function code, 8-BIT data, refer to 3.1-3
4) LEN: data length, the length of D (n-1) D (0)
5) DATA: data content,n*8-BIT data
6) CRC: cyclical redundancy check
The CRC calculation method is shown as following.
1: make a register and set value 0FFFFH (call CRC register)
2: done first byte of data Exclusive OR with low byte of CRC register
3: done right shift with CRC register and fill zero to the leftist BIT,
then check low BIT of CRC register
4: if the low BIT is zero, then repeat setp3, else CRC register do
Exclusive OR with 0A001H
5: repeat step 3 and 4, until CRC register does right shift 8 times
6: repeat step 2 to 5 for the next byte of data, until the process for all
data is complete.
The final value of CRC, register is CRC when send CRC data, Low
byte and high must exchange each other; it is to say the low byte would
67
TECORP Electronics
Manual
HC1-A User
be seat first.
7: Example:
Write 30.00Hz to inverter with address 01
command data
ADDR
FUNC
LEN
DATA
CRC
01H
02H
03H
00H 0BH B8H 7FH 0CH
Send data 01H 02H 03H 00H 0BH B8H 7FH 0CH
8: Example 2:
the following is that get CRC value with C language.
The function has two parameters
Unsigned char data the point of data buffer
Unsigned char length number of data buffer
This function will send back the CRC value with unsigned integer
format.
unsigned int crc_chk(unsigned char data unsigned char length)
int j;
unsigned int reg_crc=0xffff;
while(length)
reg_crc^=*data++;
for(j=0;j8;j++=
if(reg_crc&0x01)/*LSB(b0)=1*/
reg_crc=(reg_crc1)^0xa001;
else
reg-crc=reg_crc1;
return reg_crc;
CD163~CD167
CD168
68
Reserved
Display mode select

Set range: 015
Unit: 1
Factory setting: 0
TECORP Electronics
Manual
HC1-A User
0: not display
4
1: on display
1
DC
AC
CNT
T
DC bus voltage
Output voltage
Counter
Temperature
This parameter setting can be used to choose different items to be
displayed, such as the counting,DC voltage,AC voltage and inverter
temperature,etc.Its easy for users to monitor running status and the
items are displayed in the order by switching.
Set methodbinary 4 BIT first, then be changed into decimal system.
Related introduction refer to CD078.
CD169
Voltage class of the inverter

Unit:1V
Factory setting*
Different factory settings according to different models. Only
for checking and verifying.
CD170
Rated current of the inverter
Factory setting:*
Unit:1A
Different settings according to different models. It can not be
changed.
CD171
Software edition
Factory setting*
Only for checking and verifying.
CD172
Fault Record 1
CD173
Fault Record 2
CD174
Fault Record 3
CD175
Fault Record 4
Notemeans no fault record.
Factory setting
Factory setting
Factory setting
Factory setting
CD176
Fault cleared
**
Set range0010
Unit:1
Factory setting00
Only 01means fault cleared. Others are not valid.
69
TECORP Electronics
Manual
CD177
HC1-A User
Reserved
CD178
Frequency standard of the inverter

Set range:01
Unit:1
Factory setting*
050Hz
160Hz This parameter is a factor setting only for checking and
verifying.
CD179
Manufacture date
Factory setting*
4 3
CD180
This parameter is a factory setting, only

week for checking and verifying.
month
year
Manufacture sequence number
Factory setting*
This parameter is a factory setting, only for checking and verifying.
CD181~CD250
Reserved
Note: * means: this setting has several choices and it should be set
according to actual situation or condition.
** Means: this setting can be changed during run mode.
70
TECORP Electronics
Manual
HC1-A User
10. Maintenance, Inspection, Error Information and

Troubleshooting.
The inverter will be efficient and its service life function efficiently and
its normal operation lifetime will be longer if it has been maintained and
inspected maintenance and inspection periodically.
10.1. Precautions about maintenance and inspection:
During inspection, turn off AC power supply first.
When perform maintenance and inspection make sure that the
CHARGE lamp in the power circuit board has gone off.
During inspection, do not change the wiring, or remove connectors,
it will cause damage to the inverter.
Do not leave any metal objects in the inverter after the service, or it
will result in short circuit.
Keep the inverter clean, and dry, avoid dust, oil mist and moisture.
10.2. Periodic maintenance and inspection items
Whether the power supply voltage conforms to the rated voltage of
the inverter. (Pay special attention that whether there is any damage on
the power supply wires and the motor.)
Whether the wiring terminals and the connectors are tight.
Whether there is dust, iron filings or corrosive fluid in the inverter.
Never measure the inverter insulation impedance.
Examine the output voltage, output current and output frequency.
Whether the temperature of the inverter working space is between
-5 and 40.
Whether the humidity is kept below 90 %( no condensation).
Whether the motor is vibrating or making unusual noises in running.
Periodic cleaning of the vent holes should be done.
71
TECORP Electronics
Manual
HC1-A User
10.3. Fault indication and troubleshooting

Fault Code Content
Solution
E.OC.A Over current during
1: check whether the motor has got
acceleration
short circuit and the insulation of the
output is wires is well.
2: extend the accelerating time.
3: select a larger inverter.
4: lower the torque set value
E.OC.n Over current during
1: check whether the motor has got
constant speed
short circuit, whether the insulation
of the output wires is well.
2: check whether the motor is rotating
with some external jamming force,
whether there is a sudden change of
mechanical load.
3: select a larger inverter
4: whether there is a sudden change
of network voltage.
E.OC.d Over current during
1: whether the insulation of the
E.OC.S deceleration
output wires is well, whether the
motor has got short circuit.
2: extend the decelerating time.
4: lower the DC braking voltage.
E.GF.S Short circuit to earth 1: check whether the motor has got
E.GF.a
any short circuit.
E.GF.n
2: check whether the insulation of the
E.GF.d
output wires is well.
3: notify your supplier to check.
E.ou.S Over voltage during
1: extend the decelerating time or add
stopping
a braking resistor.
E.ou.a Over voltage during
2: correct the input voltage of the
acceleration
network source; check whether there
E.ou.n Over voltage during
is a sudden change in voltage.
constant speed
E.ou.d
Over voltage during
deceleration
72
TECORP Electronics
Manual
Fault code
E.Fb.S
E.Fb.n
E.Fb.a
E.Fb.d
E.Lu.s
E.Lu.A
E.Lu.n
E.Lu.d
E.OH.S
E.OH.A
E.OH.n
E.OH.d
Content
Fuse break
Solution
Notify your supplier to check.
Low voltage
1: check whether the input voltage in normal.

2: check whether there is sudden change of
load.
3: check whether there is any absent phase.
1: check whether the fan works well, whether
there is any foreign matter stuck in the heat
sink.
2: check whether the environment
temperature is suitable for normal working.
3: check whether there is enough ventilation
space and good air convection.
2: check whether there is any jamming in the
mechanical load.
3: select optimum V/F pattern.
1: check whether there is a sudden change of
mechanical load.
3: check whether the insulation of the motor is well.
4: check whether there is any big unsteady voltage
wave.
5: check whether there is any absent phase.
1: check whether there is any fluctuation of
mechanical load.
Inverter overheating
E.OL.A Inverter overload

E.OL.n
E.OL.d
E.OA.A Motor overload
E.OA.n
E.OA.d
E.OT.A
E.OT.n
E.OT.d
E.bS.A
E.bS.n
E.bS.d
E.bS.S
E.bT.A
E.bT.n
E.bT.d
HC1-A User
Over torque
No feedback of the
auxiliary coil of the
electromagnetic
contactor in the
inverter
Braking transistor in Notify your supplier to check.
fault
73
TECORP Electronics
Manual
Fault code
E.EC.S
E.EC.n
E.EC.d
E.EC.A
E.EE.S
E.EE.n
E.EE.d
HC1-A User
Content
Solution
CPU fault
E2 Prom fault
Notify your supplier to check
Er
External Interference Isolate from the interference source
ES
Emergency Stop
In Emergency Stop Status
20
4-20mA wire broken Join the broken wires
Pr
Setting error
Correct the setting
DCb DC braking
In DC braking status
Note:Fault Code Description:
E XX Y
means: status
means: warning information
means: fault
S: in stop status
A: in accelerating status
n: in constant speed status
d: in decelerating status
Code Comparison:
A B C D E F G H O
S
Y
N L T
10.4 Trouble shooting

(1) If the motor does not operate:
1) The operation method setting is wrong.
2) The frequency reference is too low or isnt given.
3) Multi-function input terminals function setting error.
4) Peripheral wiring is wrong, for example, the 2-wire sequence,
3-wire sequence or related setting is wrong.
5) The inverter is in the fault protection status.
6) Motor fault.
74
TECORP Electronics
Manual
HC1-A User
7) Inverter fault.
(2) The parameter can not be set:
1) Unlock the parameter lock function (CD010).
2) The inverter is in running.
3) Abnormal connection of the connectors, abnormal communication
of the digital operator. Cut off the power supply, take down the digital
operator and fit it again.
(3) The motor only rotates in FOR direction.
Reverse run prohibited is selected.
(4) If the direction of the motor rotation is reversed.
The motor output wiring is faulty. Switching two wires among U.V.W
will settle the problem.
(5) If motor deceleration is too long
1) The deceleration time setting is too long.
2) Add braking resistor.
3) Add DC brake.
(6) If the motor overheats.
1) The load is too big. Consider increasing the motor capacity.
2) The ambient temperature is too high. The motor will burn out if it
is run continuously at the rated torque in an environment in which the
maximum ambient operating temperature is exceeded. Lower the
motors ambient operating temperature.
3) The withstand voltage between the motor phases is in sufficient.
When the motor is connected to the inverter output, a surge is
generated because of the on/off of the IGBT in the and inverter.
Normally the maximum surge voltage is three times the inverters input
power supply voltage. Be sure the motor withstand voltage is high than
the maximum surge voltage.
(7) If the inverter produces interference to other devices.
1) Lower the carrier frequency.
2) Add a nose filter on the power supply input side.
3) Add a noise filter on the output side of the inverter.
4) Confirm the inverter and motor in good earth-connection status.
5) Have the wires shielded.
6) Get the main circuit wires and the control circuit wires separated.
75
TECORP Electronics
Manual
HC1-A User
(8) If the inverter detects over current when the output load is fan.
1) Get DC braking valid at starting.
2) If DC braking is already valid, please increase the DC braking
value.
(9) If there is Mechanical Vibration
1) There may be resonance between the mechanical systems
characteristic frequency and the carrier frequency.
2) There may be resonance between a machine characteristic
frequency and the output frequency of the inverter.
To prevent this, either use the jump frequency functions or install
rubber padding on the motor base to reduce vibration.
11. Peripheral devices and specification of options
11.1 Peripheral Devices
Name
Purpose and descriptions
Protect inverter wiring. Always connect a
NFB or Ground fault
breaker to the power supply line to protect
interrupter
inverter wiring. Use a ground fault
interrupter suitable for high frequencies.
Prevent burning when a Braking Resistor
Magnetic contactor
is used. Always attach a surge absorber to
the coil.
Absorb surge from the magnetic contactor
Surge absorber
and control relays.
Isolate the I/O signals of the inverter and
Isolator
is effective to reduce to interference to
other electric devices.
Used to improve the input power factor of
DC Reactor
the inverter.
Used to improve the input power factor of
AC Reactor
the inverter.
Braking resistor ,braking
Consume the regenerative energy of the
resistor unit
motor and reduce deceleration time.
76
TECORP Electronics
Manual
HC1-A User
11.2 Proper specifications of options.

11.2.1 DC Reactor
Currency Inductance
Model
Model
(A)
(mH)
001143B
40
1.10
009043B
001543B
50
1.00
011043B
18D43B
65
0.92
013243B
002243B
70
0.90
016043B
003043B
80
0.86
018543B
003743B
100
0.70
020043B
004543B
120
0.58
022043B
005543B
146
0.47
030043B
007543B
200
0.35
Currency
(A)
238
291
326
395
494
557
700
800
Inductance
(mH)
0.29
0.24
0.215
0.177
0.142
0.126
0.10
0.08
11.2.2 Input AC Reactor
Model
00D423B
0D7523B
01D523B
02D223B
0D7543B
01D543B
02D243B
03D743B
05D543B
07D543B
001143B
001543B
18D543B
002243B
003043B
003743B
004543B
005543B
Currency (A)
2.5
5
10
15
2.5
3.7
5.5
9
13
18
24
34
38
50
60
75
91
112
Inductance (mA)
4.2
2.1
1.1
0.7
8.4
2.239
2.18
1.85
1.56
1.0
0.52
0.397
0.352
0.26
0.24
0.235
0.17
0.16
77
TECORP Electronics
Manual
HC1-A User
007543B
009043B
011043B
013243B
016043B
018543B
020043B
022043B
030043B
150
180
220
265
300
360
400
560
640
0.12
0.10
0.09
0.08
0.07
0.06
0.05
0.03
0.215
11.2.3 Output AC Reactor
400V
Class
78
Model
Currency (A)
0D7543B
01D543B
02D243B
03D743B
05D543B
07D543B
001143B
001543B
18D543B
002243B
003043B
003743B
004543B
005543B
007543B
009043B
011043B
013243B
016043B
018543B
3.0
3.0
6.3
11
16
18
28
35
40
50
63
80
60
40
35
30
20
16
13
11
Inductance
(uA)
2100
2100
1450
1100
800
650
330
250
200
180
90
80
60
40
35
30
20
16
13
11
TECORP Electronics
Manual
HC1-A User
020043B
022043B
030043B
9
8
6
9
8
6
11.2.4 Braking resistor

Model
HC1A00D423B
HC1A0D7523B
HC1A01D523B
HC1A02D223B
HC1A0D7543B
HC1A01D543B
HC1A02D243B
HC1A03D743B
HC1A05D543B
HC1A07D543B
HC1A001143B
HC1A001543B
HC1A18D543B
HC1A002243B
HC1A003043B
HC1A003743B
HC1A004543B
HC1A005543B
HC1A007543B
HC1A009043B
HC1A011043B
HC1A013243B
HC1A016043B
HC1A018543B
HC1A020043B
HC1A022043B
HC1A030043B
Specifications of braking
resistor
W
80
200
100
200
300
100
300
70
80
750
300
400
300
250
400
150
500
100
1000
75
1000
50
1500
40
4800
32
4800
27.2
6000
20
9600
16
9600
13.6
12000
20/2
18000
13.6/2
18000
20/3
18000
20/3
24000
20/4
36000
13.6/4
38400
13.6/4
45000
13.6/5
48000
13.6/5
57600
13.6/6
Braking
torque
10%ED
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
Motor
power
(KW)
0.4
0.75
1.5
2.2
0.75
1.5
2.2
3.7
5.5
7.5
11
15
18.5
22
30
37
45
55
75
90
110
132
160
185
200
220
300
Braking resistor unit should be installed for inverters of 11KW or above.

79
TECORP Electronics
Manual
HC1-A User
12 Appendices
(1) Mounting Dimensions of inverters
Model
Mounting
Dimensions
B
A
CA UTION
HCI-A
High vol tageInaide
WA RNING
Do not connect ACpower to
output turbi nals( U.V.W)
Dischargi ng ti me legreater
than5 ancones.
Do not Lnspect components
unless Ins ide HARGE
lamp Is turned oft.
HC1A00D423B
HC1A01D523B
HC1A0D7543B
HC1A02D243B
10
unitmm
B
A
F
HCI-A
CAUTION
High voltage Inaide
WARNING
Do not connect AC power to
output turbinals(U.V.W)
Discharging ti me l e greater
than 5 ancones.
unless Inside HARGE
lamp Is turned oft.
10
HC1A02D223B
HC1A03D743B
unitmm
80
TECORP Electronics
Manual
HC1-A User
B
E
HCI-A
CAUTION
High voltage Inaide
HC1A05D543B
HC1A07D543B
WARNING
Do not connect AC power to
output turbinals(U.V.W)
Discharging time le greater
than 5 ancones.
unl ess Inside HARGE
lamp Is turned oft.
unitmm
B
A
HCI-A
CA UTIO N
Hig h voltag e Ina ide
HC1A001143B
HC1A004543B
W AR NING
Do n ot conn ect A C pow er t o
ou tpu t t ur bina ls(U .V.W)
Disch ar ging tim e le g re ate r
th an 5 anco nes.
Do n ot Lnsp ect comp one nts
un less I nside H ARG E
lam p I s t ur ned of t.
unitmm
81
TECORP Electronics
Manual
HC1-A User
2Specifications
Model
HC1A00D423B
HC1A0D7523B
HC1A01D523B
HC1A07D543B
HC1A01D543B
HC1A02D243B
HC1A02D223B
HC1A03D743B
HC1A05D543B
HC1A07D543B
HC1A001143B
HC1A001543B
HC1A18D543B
HC1A002243B
HC1A003043B
HC1A003743B
HC1A004543B
HC1A005543B
HPA007543B
HPA009043B
HC1A011043B
HC1A013243B
HC1A016043B
82
116
125
161
170
141
128
140
238
250
157
184
200
306
318
183
182
253
437
457
241
206
277
490
510
241
239
311
490
510
241
250
341
650
670
326
10
10
300
300
450
450
768
768
800
800
350
350
16
16
16
16
500
650
868
900
400
16
16
TECORP Electronics
Manual
HC1-A User
(2) Mounting Dimensions of Digital Operator

Model
Mounting Dimensions
54.5
58.0
FOR
REV
66.5
13.5
A ROTT
PROG
DISP
SET
RUN
STOP
13.5
HC001
70.0
FWD REV Hz
7.0
2.0
13.0
7.0
unitmm
15.3
128.0
6.3
F/R
129.6
129.0
HC002
6.3
6.2
FWD REV Hz A r/min
75.4
38.0
17.3
16.0
69.0
75.4
6.2
1.5
unitmm
83
TECORP Electronics
Manual
HC1-A User
No.4 Users feedback

Function
code
CD000
CD001
Main frequency
Max output voltage
Factory
setting
0.00
220/400
CD002
Base frequency
50.00
CD003
Function
Voltage at medium frequency 15/27.5
Function
code
CD046
CD047
CD048~
CD049
CD050
Factory
setting
Skip frequency 3
0.00
Skip frequency range
0.5
Function
Reserved
Multi-input 1
02
CD004
Medium frequency
2.50
CD051
Multi- input 2
03
CD005
Voltage at lowest frequency
8.0/13.5
CD052
Multi- input 3
10
CD006
CD007
Lowest frequency
Max operating frequency
0.50
50.00
CD053
CD054
Multi- input 4
Multi- input 5
17
18
CD008
Frequency upper limit
50.00
CD055
Multi- input 6
19
CD009
CD010
CD011
Frequency lower limit

Factory setting
0.00
0
00
CD056
CD057
CD058
Multi- output 1
Multi- output 2
Multi- output 3
01
05
02
CD012
Accel.time 1
10.0/25.0
CD059
Multi- output 4
00
CD013
Decel.time 1
10.0/25.0
CD060
Multi- output 5
CD014
Accel.time 2
50.0
CD061
0.00
CD015
Decel.time 2
50.0
CD062
CD016
Accel.time 3
100.0
CD063
Up-to desired frequency

1 setting
Up-to desired frequency
2 setting
Up-to frequency setting
detection width
CD017
Decel.time 3
100.0
CD064
Counter set
00
CD018
Accel.time 4
200.0
CD065
Analog input select
CD066
Lower analog frequency

set point
Lower analog frequency
bias direction
Higher analog frequency
set point
Higher analog frequency
bias direction
CD019
Decel.time 4
CD020~
CD030
200.0
Reserved
CD031
Start mode
CD068
CD032
Stop mode
CD069
CD067
0.00
0.50
0
50.00
0
CD033
Control mode select
CD070
Negative bias reverse

select
CD034
Frequency command
method select
CD071
Analog output gain
100
CD035
Carrier frequency
CD072
Up/down frunction
select
Reserved
CD036
Jog frequency
5.00
CD073~
CD075
CD037
FOR/REV select
CD076
PLC mode select
CD038
STOP key definition
CD077
Auto PLC select
CD039~
CD040
Reserved
CD078
PLC running direction
84
TECORP Electronics
Manual
Function
code
Function
HC1-A User
Factory
setting
Function
code
Function
Factory
setting
CD041
Starting frequency
0.5
CD079
PLC accel./decel.time
CD042
Stopping frequency
0.5
CD080
Multi-speed2
15.00
CD043
Torque boost
2.0
CD081
Multi-speed3
20.00
CD044
CD045
Skip frequency 1
Skip frequency 2
0.00
0.00
CD082
CD083
25.00
30.00
CD084
Multi-speed6
35.00
CD146
CD085
Multi-speed7
40.00
CD147
CD086
Multi-speed8
0.50
CD148
Multi-speed4
Multi-speed5
Power loss time
allowable
Number of auto
restart attempt
Auto voltage
regulation
CD087
Timer 1
10.0
CD149
Auto energy saving
CD088
Timer 2
10.0
CD150
100%
CD089
Timer 3
0.0
CD151
5.0
CD090
Timer 4
0.0
CD152
CD091
Timer 5
0.0
CD153
Target value
CD092
Timer 6
0.0
CD154
Target value source
CD093
Timer 7
0.0
CD155
PID upper limit
100%
CD094
Timer 8
0.0
CD156
PID lower limit
0%
CD095~
CD119
CD120
CD121
CD122
CD123
CD124
CD157~
CD159
Reserved
during accel
during running
during decek
CD160
150
CD161
CD162
150
CD163~
CD167
Reserved
CD168
CD125
Over torque detection level
CD169
1.0
CD170
CD126
Over torque detection time
CD127~
CD129
Reserved
CD130
Rated voltage
CD131
0.5
00
1
Reserved
Communication
identified no.
Baud rate of
communication
Communication
agreement
0
1
0
Reserved
Display mode
Rated voltage of the
inverter
Rated current of the
inverter
00
*
*
CD171
Software version
CD172
Fault record 1
Rated current
CD173
Fault record 2
CD132
Motor poles
04
CD174
Fault record 3
CD133
Rated rotating speed
1440
CD175
Fault record 4
85
TECORP Electronics
Manual
Function
code
CD134~
CD139
Function
DC braking level
CD141
DC braking time at starting
CD142
CD143
CD145
86
Factory
setting
Reserved
CD140
CD144
HC1-A User
Function
Factory
setting
CD176
Fault cleared
00
CD177
Reserved
0.0
CD178
Frequency standard of the

inverter
0.0
CD179
Manu faction date
Speed search time
5.0
CD180
Sequence number
150
CD181~
CD250
Reserved
Speed search current level
2.0
Function
code

HC1 A Manual EN

Uploaded by

Copyright:

Available Formats

HC1 A Manual EN

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HC1 A Manual EN

Uploaded by

Copyright:

Available Formats

TECORP Electronics

HC1-A User Manual

HC1-A User Manual

7. Trial Operation ------------------------------------------------ 19

This operation manual is 1.37 versions. Specifications are

HC1-A User Manual

WARNING Indicates precautions that, if not avoided, could

HC1-A User Manual

1.2 Nameplate information

HC1-A User Manual

HC1-A User Manual

to the inverter. The installation diagram like this is forbidden.

2.2 In delivery of current

HC1-A User Manual

HC1-A User Manual

3.2 Common Specifications

HC1-A User Manual

HC1-A User Manual

The suitable temperature for storage is between -20and +65.

HC1-A User Manual

No fuse breaker or ground fault interrupter.

AC reactor for power factor improvement.

TECORP Inverter (HC1-A series)

3 phases squirrel cage induction motor.

HC1-A User Manual

5.2.2 Control circuit terminals arrangement

EV SPL SPM SPH RST DCM REV FOR

SPH RST REV FOR +10 VI AI ACM AM

HC1-A User Manual

5.2.3 Function description of main circuit terminals

5.2.4 Function description of control circuit terminals

Max output current 200mA

Multi-function output terminal 2

Fault Relay output(N/O or

HC1-A User Manual

5.3 Standard Connection Diagram

Multi-function output <relay N/0 N/C>

Multi-function output <OP>

Analog frequency output

Multi-function output <Relay N/O>

Multi-function output <Relay N/O N/C>

Multi-function output <Relay OP>

Analog frequency output

HC1-A User Manual

5.4 Cautions on Wiring

HC1-A User Manual

Specifications for NFB and Wire

5.4.2 For control circuit wiring (signal line)

HC1-A User Manual

Use the control terminals correctly according to your needs.

HC1-A User Manual

6. Description of Digital Operator

Operation Mode Indicators

Forward or reverse run key

Numerical change key

Forward or reverse run key

Numerical change key

HC1-A User Manual