Cisco Aironet 350 340 AP350higp

Cisco Aironet Access Point
Hardware Installation Guide

340 Series and 350 Series
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Text Part Number: OL-0738-02
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Ciscos installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Ciscos written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
Turn the television or radio antenna until the interference stops.
Move the equipment to one side or the other of the television or radio.
Move the equipment farther away from the television or radio.
Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCBs public
domain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CCSP, the Cisco Square Bridge logo, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live,
Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco
Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation,
Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness
Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect,
RateMUX, Registrar, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are
registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0406R)
Cisco Aironet Access Point Hardware Installation Guide

Copyright 2004 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
vii
Objectives
vii
Audience
vii
Organization
vii
Conventions
viii
Related Publications
viii
Obtaining Documentation ix
Cisco.com ix
Ordering Documentation ix
Documentation Feedback
ix
Obtaining Technical Assistance x

Cisco TAC Website x
Opening a TAC Case x
TAC Case Priority Definitions x
Obtaining Additional Publications and Information
CHAPTER
Overview
xi
1-1
Key Features 1-2

Inline Power 1-2
Omni-Directional Antennas 1-2
Ethernet and Serial Ports 1-3
Ethernet Port 1-3
Serial Port 1-3
Metal Enclosure 1-3
Indicators 1-4
Network Configuration Examples 1-5
Root Unit on a Wired LAN 1-5
Repeater Unit That Extends Wireless Range 1-6
Central Unit in an All-Wireless Network 1-7
Access Point Specifications
CHAPTER
Installation
1-8
2-1
Cautions and Warnings
2-2

OL-0738-02
iii
Contents
Installation Guidelines 2-3

Basic Guidelines 2-3
Special Considerations 2-3
Coverage Options 2-3
Minimal Overlap Coverage Option 2-4
Multiple Overlapping Networks Coverage Option
Heavy Overlap Coverage Option 2-5
Site Surveys 2-5
2-4
Unpacking the Access Point 2-6

Package Contents 2-6
Connecting the Ethernet and Power Cables 2-7
Connecting Cables on 340 Series Access Points
CHAPTER
Basic Configuration
Before You Start
3-2
3-2
Using the IP Setup Utility 3-2

Obtaining and Installing IPSU 3-3
Finding the Access Points IP Address 3-3
Setting the Access Points IP Address and SSID
Entering Basic Settings 3-5
Using an Internet Browser 3-5
Using a Terminal Emulator 3-7
Selecting Pages and Settings 3-7
Applying Changes to the Configuration
Assigning Basic Settings 3-7
Default Basic Settings
4
Troubleshooting
2-8
3-1
Summary of Configuration Steps
CHAPTER
2-7
3-4
3-7
3-10
4-1
Checking the Top Panel Indicators

Checking Basic Settings
SSID 4-3
WEP Keys 4-3
4-2
4-3
Resetting to the Default Configuration 4-4

Steps for Firmware Versions 11.07 or Later 4-4
Steps for Firmware Versions 11.06 or Earlier 4-5
Determining the Boot-Block Version 4-5
iv
OL-0738-02
Contents
Reconfiguration Steps for Boot Block Version 1.01 or Earlier 4-6

Reconfiguration Steps for Boot Block Version 1.02 or Later 4-7
APPENDIX
Translated Safety Warnings
A-1
Explosive Device Proximity Warning

Lightning Activity Warning
Installation Warning
A-3
A-3
Circuit Breaker (15A) Warning

Power Injector Warning
APPENDIX
A-2
A-4
A-6
Declarations of Conformity and Regulatory Information
B-1
Manufacturers Federal Communication Commission Declaration of Conformity Statement
B-2
Department of Communications Canada B-3

Canadian Compliance Statement B-3
European Community, Switzerland, Norway, Iceland, and Liechtenstein B-4
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC
Declaration of Conformity for RF Exposure
B-5
Guidelines for Operating Cisco Aironet Access Points and Bridges in Japan
Japanese Translation B-6
English Translation B-6
Declaration of Conformity Statements
B-4
B-6
B-7
Declaration of Conformity Statement for European Union Countries
B-7
INDEX

OL-0738-02
Contents
vi
OL-0738-02
Preface
This section describes the objectives, audience, organization, and conventions of the Cisco Aironet
Access Point Hardware Installation Guide.
Objectives
This publication explains the steps for initial setup and configuration of the access point. This
publication also provides troubleshooting information and detailed specifications.
Audience
This publication is for the person installing and configuring a Cisco Aironet Access Point for the first
time. The installer should be familiar with network structures, terms, and concepts.
Organization
This guide contains the following sections:
Chapter 1, Overview, describes the features and specifications of access points.
Chapter 2, Installation, provides basic installation instructions.
Chapter 3, Basic Configuration, describes how to enter basic configuration settings.
Chapter 4, Troubleshooting, provides solutions to potential problems encountered during setup.
Appendix A, Translated Safety Warnings, lists translations of the safety warnings in this publication.
Appendix B, Declarations of Conformity and Regulatory Information, describes the regulatory
conventions to which the access point conforms and provides guidelines for operating access points in
Japan.

OL-0738-02
vii
Preface
Conventions
Conventions
This publication uses the following conventions to convey instructions and information:
Note
Caution
Warning
Commands and keywords are in boldface type.
Means reader take note. Notes contain helpful suggestions or references to materials not contained in
this manual.
Means reader be careful. In this situation, you might do something that could result in equipment
damage or loss of data.
The warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. To see translations of the warnings that appear
in this publication, refer to Appendix A in this manual.
Related Publications
For more information about access points and related products, refer to the following publications:
Quick Start Guide: Cisco Aironet Access Points describes how to attach cables, power on, and assign
an IP address and default gateway for the access point.
Cisco Aironet Access Point Software Configuration Guide describes the access points management
system and explains how to configure the access point.
Release Notes for Cisco Aironet Access Points describes features and caveats for access points
running firmware release 10.14.
Cisco Secure Access Control Server for Windows 2000/NT Servers Version 2.6 User Guide provides
complete instructions for using Cisco Secure ACS, including steps for configuring Cisco Secure
ACS to support access points.
Quick Start Guide: Cisco Aironet Wireless LAN Adapters describes how to install and configure PC
and PCI card client adapters for use in a wireless LAN.
Cisco Aironet Wireless LAN Adapters Hardware Installation Guide provides hardware features,
physical and performance characteristics, and installation instructions for PC and PCI card client
adapters.
Cisco Aironet Wireless LAN Adapters Software Configuration Guide provides instructions for
installing and using the wireless client adapter utilities.
viii
OL-0738-02
Preface
Obtaining Documentation
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation on the World Wide Web at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
http://www.cisco.com
International Cisco websites can be accessed from this URL:
http://www.cisco.com/public/countries_languages.shtml
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from
the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/index.shtml
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 800 553-NETS (6387).
Documentation Feedback
You can submit e-mail comments about technical documentation to bug-doc@cisco.com.
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
San Jose, CA 95134-9883
We appreciate your comments.

OL-0738-02
ix
Preface
Obtaining Technical Assistance
Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco
Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services,
online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for
technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.
Cisco TAC Website

The Cisco TAC website provides online documents and tools for troubleshooting and resolving technical
issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365
days a year. The Cisco TAC website is located at this URL:
http://www.cisco.com/tac
Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password. If you
have a valid service contract but do not have a login ID or password, register at this URL:
http://tools.cisco.com/RPF/register/register.do
Opening a TAC Case

Using the online TAC Case Open Tool is the fastest way to open P3 and P4 cases. (P3 and P4 cases are
those in which your network is minimally impaired or for which you require product information.) After
you describe your situation, the TAC Case Open Tool automatically recommends resources for an
immediate solution. If your issue is not resolved using the recommended resources, your case will be
assigned to a Cisco TAC engineer. The online TAC Case Open Tool is located at this URL:
http://www.cisco.com/tac/caseopen
For P1 or P2 cases (P1 and P2 cases are those in which your production network is down or severely
degraded) or if you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC engineers
are assigned immediately to P1 and P2 cases to help keep your business operations running smoothly.
To open a case by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete listing of Cisco TAC contacts, go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
TAC Case Priority Definitions

To ensure that all cases are reported in a standard format, Cisco has established case priority definitions.
Priority 1 (P1)Your network is down or there is a critical impact to your business operations. You
and Cisco will commit all necessary resources around the clock to resolve the situation.
Priority 2 (P2)Operation of an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco
will commit full-time resources during normal business hours to resolve the situation.
OL-0738-02
Preface
Priority 3 (P3)Operational performance of your network is impaired, but most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Priority 4 (P4)You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.

Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Go
to this URL to visit the company store:
http://www.cisco.com/go/marketplace/
The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as
ordering and customer support services. Access the Cisco Product Catalog at this URL:
http://cisco.com/univercd/cc/td/doc/pcat/
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press online at this URL:
http://www.ciscopress.com
Packet magazine is the Cisco quarterly publication that provides the latest networking trends,
technology breakthroughs, and Cisco products and solutions to help industry professionals get the
most from their networking investment. Included are networking deployment and troubleshooting
tips, configuration examples, customer case studies, tutorials and training, certification information,
and links to numerous in-depth online resources. You can access Packet magazine at this URL:
http://www.cisco.com/packet
iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet
business strategies for executives. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
TrainingCisco offers world-class networking training. Current offerings in network training are
listed at this URL:
http://www.cisco.com/en/US/learning/index.html

OL-0738-02
xi
Preface
xii
OL-0738-02
C H A P T E R
Overview
The Cisco Aironet access point is a wireless LAN transceiver that serves as the center point of a
stand-alone wireless network or as the connection point between wireless and wired networks. In large
installations, wireless users within radio range of an access point can roam throughout a facility while
maintaining uninterrupted access to the network.
This chapter provides information on the following topics:
Key features
Network configuration examples
Access point specifications

OL-0738-02
1-1
Chapter 1
Overview
Key Features
Key Features
This section describes the key features of the access point:
Inline power
Omni-directional antennas
Ethernet and serial ports
Indicators
Industrial temperature range and UL 2043 rating for 350 series metal case access point
Inline Power
Cisco Aironet 350 series access points receive power through the Ethernet cable, so you do not need to
run a separate power cord to the access point. Plug the Ethernet cable into the Ethernet port on the back
of the access point and plug the other end into one of three possible power sources:
A Cisco Aironet power injector
A switch with inline power, such as the Cisco Catalyst 3524-PWR-XL switch
A power patch panel, such as the Cisco Catalyst Inline Power Patch Panel
Note
Cisco Aironet 340 series access points rely on a separate power supply plugged into the power port on
the back of the access point.
Caution
Cisco Aironet power injectors are designed for use with 350 series access points and bridges only. Using
the power injector with other Ethernet-ready devices can damage the equipment.
Caution
Cisco Aironet Power Injectors are not rated for operation in a buildings environmental air space, such
as above suspended ceilings.
Caution
The operational voltage range for Cisco Aironet 350 series access points and bridges is 24 to 60 VDC.
Higher voltage can damage the equipment.
Omni-Directional Antennas
The access points omni-directional, 2.2 dBi antennas provide diversity coverage for your wireless LAN
area. Diversity coverage helps maintain a clear radio signal between the access point and wireless client
devices. Just as you can improve signal clarity on your car radio at a stoplight by creeping ahead a few
inches, the access point can improve signal quality by choosing the antenna that is receiving the best
signal from a client device.
Some access points models are equipped with dual reverse-polarity TNC connectors that you can use to
connect to your own antennas for special applications.
1-2
OL-0738-02
Chapter 1
Overview
Key Features
Ethernet and Serial Ports

Ethernet Port
The access points Ethernet port accepts an RJ-45 connector, linking the access point to your 10/100
Ethernet LAN. The 350 series access point receives power through the Ethernet cable from a switch with
inline power, from a power patch panel, or from the access points power injector.
Serial Port
The access points serial port provides console access to the access points management system. Use a
nine-pin, straight-through, male-to-female serial cable to connect your computers COM 1 or COM 2
port to the access points serial port. Assign the following port settings to a terminal emulator to open
the management system pages: 9600 baud, 8 data bits, No parity, 1 stop bit, and Xon/Xoff flow control.
Metal Enclosure
The 350 series metal case access point contains a metal enclosure having adequate fire resistance and
low smoke-producing characteristics suitable for operation in a buildings environmental air space in
accordance with Section 300-22(c) of the NEC. The 350 series metal case access point also supports an
industrial temperature operating range.

OL-0738-02
1-3
Chapter 1
Overview
Key Features
Indicators
The three indicators on top of the access point report Ethernet activity, association status, and radio
activity. The indicators are labeled in Figure 1-1 and Figure 1-2.
Figure 1-1
Indicators on the 340 and 350 Series Access Point
CISCO AIRONET 350 SERIES

W I R E L E S S AC C E S S P O I N T
Radio
Figure 1-2
49075
Ethernet
Status
Indicators on the 350 Series Metal Case Access Point

WIRELESS ACCESS POINT
ETHERNET ACTIVITY
ASSOCIATION STATUS
60511
RADIO ACTIVITY
Ethernet
Status
Radio
The Ethernet indicator signals Ethernet traffic on the wired LAN. This indicator blinks green when
a packet is received or transmitted over the Ethernet infrastructure. The indicator blinks red when
the Ethernet cable is not connected.
The association status indicator signals operational status. Blinking green indicates that the access
point is operating normally but is not associated with any wireless client devices. Steady green
indicates that the access point is associated with at least one wireless client device.
The radio indicator blinks green to indicate radio traffic activity. The light is normally off, but it
blinks green whenever a packet is received or transmitted over the access point radio.
1-4
OL-0738-02
Chapter 1
Overview
Network Configuration Examples

This section describes the access points role in three common wireless network configurations. The
access points default configuration is as a root unit on a wired LAN. The other two possible roles,
repeater unit and central unit in an all-wireless network, require specific changes to the default
configuration.
Root Unit on a Wired LAN

An access point connected directly to a wired LAN provides a connection point for wireless users. If
more than one access point is connected to the LAN, users can roam from one area of a facility to another
without losing their connection to the network. As users move out of range of one access point, they
automatically connect to the network (associate) through another access point. The roaming process is
seamless and transparent to the user. Figure 1-3 shows access points acting as root units on a wired LAN.
Figure 1-3
Access Points as Root Units on a Wired LAN
Access Point
(Root Unit)
Access Point
(Root Unit)
45835
Wired LAN

OL-0738-02
1-5
Chapter 1
Overview
Repeater Unit That Extends Wireless Range

An access point can be configured as a stand-alone repeater to extend the range of your infrastructure or
to overcome an obstacle that blocks radio communication. The repeater forwards traffic between
wireless users and the wired LAN by sending packets to either another repeater or to an access point
connected to the wired LAN. The data is sent through the route that provides the greatest performance
for the client. Figure 1-4 shows an access point acting as a repeater.
Figure 1-4
Access Point as Repeater

Access Point
(Root Unit)
Wired LAN
45836
Access Point
(Repeater)
1-6
OL-0738-02
Chapter 1
Overview
Central Unit in an All-Wireless Network

In an all-wireless network, an access point acts as a stand-alone root unit. The access point is not
attached to a wired LAN; it functions as a hub linking all stations together. The access point serves as
the focal point for communications, increasing the communication range of wireless users. Figure 1-5
shows an access point in an all-wireless network.
Figure 1-5
Access Point as Central Unit in All-Wireless Network
45834
Access Point
(Root Unit)

OL-0738-02
1-7
Chapter 1
Overview

Table 1-1 lists specifications for the access point.
Table 1-1
Category
Specification
Physical
Size
6.30 in. (16 cm) W x 4.72 in. (12 cm) D x 1.45 in. (3.7 cm) H
Status indicators
Three indicators on the top panel: Ethernet traffic, status, and

radio traffic
Connectors
On the back panel: An RJ-45 jack for 10/100 Ethernet

connections; a nine-pin serial connector; a power connector
(plug-in AC adapter) for a regulated 5V input (340 series
only)
Voltage range
24 to 60 VDC (regulated 5 VDC for 340 series only)
Operating temperature range
32 to 122oF (0 to 50oC) for 340 and 350 series

4 to 131oF (20 to 55oC) for 350 series metal case
32 to 104oF (0 to 40oC) for power injectors
Weight
Less than 1 lb (0.45 kg) for 340 and 350 series

1.43 lbs (0.64 kg) for 350 series metal case
Radio
Power output
100, 50, 30, 20, 5, or 1 mW for 350 series

30, 20, 5, or 1 mW for 340 series
(Depending on the regulatory domain in which the access point
is installed)
Frequency
2.400 to 2.497 GHz (Depending on the regulatory domain in

which the access point is installed)
Range
Indoor:
150 ft at 11 Mbps (100 ft for 340 series only)
Outdoor:
Modulation
Direct Sequence Spread Spectrum
Data rates
1, 2, 5.5, and 11 Mbps
1-8
OL-0738-02
Chapter 1
Overview
Table 1-1
Category
Access Point Specifications (continued)
Specification
Antenna
Two captured 2.2 dBi gain antennas or a diversity system with

two reverse-TNC connectors (antennas for this model are sold
separately). Some models in the 340 series have one 2.2 dBi
gain antenna.
Compliance
Operates license-free under FCC Part 15 and complies as a

Class B computing device. Complies with DOC regulations.
Complies with the following: ETS 300.328, FTZ 2100, MPT
1349, FCC Part 15.107 and 15.109 Class B, ICES-003 Class
B (Canada), CISPR 22 Class B, AS/NZS 3548 Class B, VCCI
Class B, EN 50082-1, UL1950, CSA 22.2 No. 950, EN 60950,
IEC 60950, VCCI, and others (see Appendix B).
350 series metal case access point complies with UL 2043 for
products installed in air handling spaces, such as above
suspended ceilings.
Caution
Cisco Aironet Power Injectors are not

rated for UL 2043 and should not be
placed in air handling spaces, such as
above suspended ceilings.

OL-0738-02
1-9
Chapter 1
Overview
1-10
OL-0738-02
C H A P T E R
Installation
This chapter describes the setup of the access point and includes the following sections:
Installation Guidelines
Unpacking the Access Point
Connecting the Ethernet and Power Cables

OL-0738-02
2-1
Chapter 2
Installation

Translated versions of the following safety warnings are provided in Appendix A, Translated Safety
Warnings.
Note
The FCC, with its action in ET Docket 96-8, has adopted a safety standard for human exposure to
radiated frequency (RF) electromagnetic energy emitted by FCC-certified equipment. Cisco Aironet
products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper
operation of this radio device according to the instructions in this publication will result in user exposure
substantially below the FCC recommended limits.
Caution
Caution
The operational voltage range for Cisco Aironet 350 series access points and bridges is 24 to 60 volts.
Caution
Warning
Do not operate your wireless network device near unshielded blasting caps or in an explosive
environment unless the device has been modified to be especially qualified for such use.
Warning
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Warning
Read the installation instructions before you connect the system to its power source.
Warning
This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that
a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the
phase conductors (all current-carrying conductors).
2-2
OL-0738-02
Chapter 2
Installation
This section describes things to keep in mind when installing your access point. Sections include:
Basic Guidelines
Special Considerations
Coverage Options
Site Surveys
Basic Guidelines
Because the access point is a radio device, it is susceptible to common causes of interference that can
reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:
Install the access point in an area where large steel structures such as shelving units, bookcases, and
filing cabinets do not obstruct radio signals to and from the access point.
Install the access point away from microwave ovens. Microwave ovens operate on the same
frequency as the access point and can cause signal interference.
Special Considerations
The 350 series metal case access point provides adequate fire resistance and low smoke-producing
characteristics suitable for operation in a buildings environmental air space, such as above suspended
ceilings. This access point is intended for indoor use and can be used in environments where the temperature
ranges from -4 to 131oF (-20 to 55oC).
Caution
Coverage Options
The network architecture options of wireless stations and access points provide for a variety of coverage
alternatives and flexibility. The network can be designed to provide a wide coverage area with minimal
overlap or a narrow coverage area with heavy overlap. A narrow coverage area with heavy overlap
improves network performance and protection against downtime if a component fails.

OL-0738-02
2-3
Chapter 2
Installation
Minimal Overlap Coverage Option

By arranging the access points so that the overlap in a coverage area is minimized, a large area can be
covered with minimal cost (see Figure 2-1). The total bandwidth available to each wireless client device
depends on the amount of data each mobile station needs to transfer and the number of stations located
in each cell. Seamless roaming is supported as a client device moves in and out of range of each access
point, thereby maintaining a constant connection to the wired LAN. Each device in the radio network
must be configured with the same SSID to provide roaming capability.
Figure 2-1
Minimal Overlap Coverage Option
46223
Wired LAN

Multiple networks can operate in the same vicinity (see Figure 2-2). The architecture provides multiple
channels that can exist in the same area with virtually no interference to each other. In this mode, each
system must be configured with different SSIDs and different channels, which may (depending on
configurations) prevent clients from roaming to access points of a different wireless network.
Figure 2-2

Wired LAN 2
46225
Wired LAN 1
2-4
OL-0738-02
Chapter 2
Installation
Heavy Overlap Coverage Option

By arranging the access points so the overlap in coverage area is nearly maximized, a large number of
mobile stations can be supported in the same wireless infrastructure (see Figure 2-3). However, devices
in overlapping coverage areas on the same frequency will detect adjacent cell traffic and delay
transmissions that would cause collisions. This configuration reduces the aggregate radio system
throughput. Heavy cell overlap is not recommended for maximum system throughput.
Because of the redundancy in coverage overlap, network access is not lost if an access point fails. Upon
failure of the access point, the station automatically roams to an operational access point. With this
architecture, each device in the RF network must be configured with the same SSID to provide the
roaming capability.
Figure 2-3
Heavy Overlap Coverage Option
46224
Wired LAN
Site Surveys
Because of differences in component configuration, placement, and physical environment, every
network application is a unique installation. Before installing multiple access points, you should perform
a site survey to determine the optimum utilization of networking components and to maximize range,
coverage, and network performance.
Consider the following operating and environmental conditions when performing a site survey:
Data rates Sensitivity and range are inversely proportional to data bit rates. The maximum radio
range is achieved at the lowest workable data rate. A decrease in receiver threshold sensitivity occurs
as the radio data increases.
Antenna type and placement Proper antenna configuration is a critical factor in maximizing radio
range. As a general rule, range increases in proportion to antenna height.
Physical environment Clear or open areas provide better radio range than closed or filled areas.
Also, the less cluttered the work environment, the greater the range.
Obstructions A physical obstruction such as metal shelving or a steel pillar can hinder performance
of wireless devices. Avoid locating the devices in a location where there is a metal barrier between
the sending and receiving antennas.

OL-0738-02
2-5
Chapter 2
Installation
Building materials Radio penetration is greatly influenced by the building material used in
construction. For example, drywall construction allows greater range than concrete blocks. Metal or
steel construction is a barrier to radio signals.

Follow these steps to unpack the access point:
Step 1
Open the shipping container and carefully remove the contents.
Step 2
Return all packing materials to the shipping container and save it.
Step 3
Ensure that all items listed in the Package Contents section are included in the shipment. Check each
item for damage.
Package Contents
Each access point is shipped with the following items:
Note
Cisco Aironet Access Point
AC to DC power adapter (340 series only)
Cisco Aironet power injector (350 series only)
Nine-pin, male-to-female, straight-through serial cable
Quick Start Guide: Cisco Aironet Access Points
Cisco Aironet Access Point CD-ROM
Cisco Information Packet, which contains warranty, safety, and support information
Cisco product registration card
If any item is damaged or missing, notify your authorized Cisco sales representative.
2-6
OL-0738-02
Chapter 2
Installation

Because of hardware differences, setup procedures differ for 340 series access points and 350 series
access points. Cabling instructions for each series are included in the following sections:

Follow these steps to connect the Ethernet cable and power supply on 340 series access points:
Step 1
Plug the RJ-45 Ethernet connector into the Ethernet port on the back of the access point.
Step 2
Connect the other end of the Ethernet cable to the 10/100 Ethernet LAN.
Caution
Note
Do not connect the Ethernet cable when the access point is powered up. Always connect the Ethernet
cable before you apply power to the access point.
The access point does not have an on/off switch, so power is applied to the unit when you plug it in.
Step 3
Plug the power adapter into a suitable power receptacle.
Step 4
Plug the power connector into the back of the access point.
At start-up, all three LEDs on the top of the access point slowly blink amber, red, and green in sequence;
the sequence takes a few minutes to complete. During normal operation, the LEDs blink green. Refer to
Chapter 4, Troubleshooting, for LED descriptions.
Step 5
Follow the steps in Chapter 3, Basic Configuration to assign basic settings to the access point.

OL-0738-02
2-7
Chapter 2
Installation

Follow these steps to connect the Ethernet cable and power supply on 350 series access points:
Step 1
Plug the RJ-45 Ethernet connector into the Ethernet port on the back of the access point.
Step 2
Choose a power option for the access point. The 350 series access point receives power through the
Ethernet cable. Figure 2-4 shows the three power options for the access point.
Figure 2-4
Access Point Power Options
Option 1
Option 2
Option 3
Switch
(without inline power)
Switch with
inline power
SYST
RPS
STAT
UTIL DUPLX
SPEED
MODE
10Base-T
10
11
12
Switch
(without inline power)
/ 100Base-TX
13
14
15
16
17
18
19
20
Catalyst 2950
21
22
23
24
SERIES
100Base-FX
23
24
SYST
RPS
STAT
UTIL DUPLX
MODE
SYST
RPS
STAT
UTIL DUPLX
SPEED
MODE
10Base-T
10
11
12
SPEED
10Base-T
10
11
12
/ 100Base-TX
13
14
15
16
17
18
19
20
Catalyst 2950
21
22
23
24
SERIES
100Base-FX
23
24
/ 100Base-TX
13
14
15
16
17
18
19
20
Catalyst 2950
21
22
23
24
SERIES
100Base-FX
23
24
Inline Power
Patch Panel
O
T OR
W
T
E
Power injector
SYST
UTIL DUPLX
SPEED
A
O G
T ID
R
B
/
MODE
RPS
STAT
Power
cord
Universal
power supply
Access Point
Power options include:
A switch with inline power, such as a Cisco Catalyst 3524-PWR-XL
An inline power patch panel, such as a Cisco Catalyst Inline Power Patch Panel
A Cisco Aironet power injector
Caution
Caution
The operational voltage range for Cisco Aironet 350 series access points and bridges is 24 to 60 VDC.
2-8
OL-0738-02
Chapter 2
Installation
Step 3
Connect the other end of the Ethernet cable to the device that will supply power.
If you use a power injector, follow these additional steps:
a.
Plug the cable from the access point into the end of the power injector labeled To AP/Bridge.
b.
Run an Ethernet cable from the end of the power injector labeled To Network to the 10/100 Ethernet
switch.
c.
Plug the female end of the power cord into the universal power supply.
d.
Plug the male end of the power cord into a power outlet or power strip.
At start-up, all three LEDs on the top of the access point slowly blink amber, red, and green in sequence;
the sequence takes a few minutes to complete. During normal operation, the LEDs blink green. Refer to
Chapter 4, Troubleshooting, for LED descriptions.
Step 4
Follow the steps in Chapter 3, Basic Configuration, to assign basic settings to the access point.

OL-0738-02
2-9
Chapter 2
Installation
2-10
OL-0738-02
C H A P T E R
Basic Configuration
This chapter describes initial configuration of the access point using the Internet browser-based
management system. You can also reach the management system through the access points serial port
or through Telnet. Consult Chapter 2 in the Cisco Aironet Access Point Software Configuration Guide
for complete instructions on using these interfaces.
This chapter includes the following sections:
Before You Start
Using the IP Setup Utility
Entering Basic Settings

OL-0738-02
3-1
Chapter 3
Basic Configuration
Before You Start
Before You Start

Before configuring the access point, ask your network administrator for the following information:
The service set identifier (SSID) for the access point.
A system name for the access point. The name should describe the location or principal users of the
access point.
If your network does not use DHCP to assign IP addresses, you will need an IP address for the access
point.
If your network uses subnets, you will need a default gateway and an IP subnet mask for the access
point.
The access points MAC address, which is printed on the label on the bottom of the access point.

You use the Express Setup page to assign basic settings to the access point. For instructions on setting
up security, filtering, and other access point features, consult the Cisco Aironet Access Point Software
Configuration Guide on the access point CD.
You will follow these steps to enter the access points basic settings:
1.
Connect the access point as described in the Quick Start Guide: Cisco Aironet Access Points.
2.
Use an Internet browser to open the access points management system by browsing to the access
points IP address. If your network uses a DHCP server, use the IP Setup Utility (IPSU) to find the
access points DHCP-assigned IP address. The Using the IP Setup Utility section on page 3-2
describes how to use IPSU.
You can also use a nine-pin, straight-through, male-to-female serial cable to connect your
computers COM1 or COM2 port to the serial port on the back of the access point and use a terminal
emulator to open the management system. The Using a Terminal Emulator section on page 3-7
describes using a terminal emulator to assign basic settings.
3.
Enter basic settings on the Express Setup page.

The IP Setup utility (IPSU) allows you to find the access points IP address when it has been assigned
by a DHCP server. You can also use IPSU to set the access points IP address and SSID if they have not
been changed from the default settings.
Note
IPSU can be used only on the following operating systems: Windows 95, 98, NT, 2000, ME, or XP. For
other operating systems, you must use the access point console port and a terminal emulator program to
configure the access point.
The sections below explain how to install the utility, how to use it to find the access points IP address,
and how to use it to set the IP address and the SSID.
3-2
OL-0738-02
Chapter 3
Basic Configuration
Obtaining and Installing IPSU

IPSU is available on the Cisco web site. Follow these steps to obtain and install IPSU:
Step 1
Use your Internet browser to access the Cisco Software Center at the following URL:
http://www.cisco.com/public/sw-center/sw-wireless.shtml
Step 2
Click Option 2: Aironet Wireless Software Display Tables.
Step 3
Locate the access point firmware and utilities section and click Cisco Aironet 350 Series (VXWorks).
Step 4
Click IPSUvxxxxxx.exe. The vxxxxxx identifies the software package version number.
Step 5
On the Encryption Authorization Form, enter the requested information, read the encryption
information, and check the boxes that apply.
Step 6
Click Submit.
Step 7
Read and accept the terms and conditions of the Software License Agreement.
Step 8
Select the file again to download it.
Step 9
Download and save the file to a temporary directory on your hard drive and then exit the Internet browser.
Step 10
Double-click IPSUvxxxxxx.exe in the temporary directory to expand the file.
Step 11
Double-click Setup.exe and follow the steps provided by the installation wizard to install IPSU.
The IPSU icon appears on your computer desktop.
Finding the Access Points IP Address

If your access point receives an IP address from a DHCP server, use IPSU to find its IP address. Run
IPSU from a computer on the same network as the access point. Follow these steps to find the access
points IP address:
Step 1
When the utility window opens, make sure Get IP addr is selected in the Function box.
Step 2
Type the access points MAC address in the Device MAC ID field. The access points MAC address is
printed on the label on the bottom of the unit. It should contain six pairs of hexadecimal digits. Your
access points MAC address might look like the following example:
004096xxxxxx
Note
The MAC address field is not case-sensitive.
Step 3
Click Get IP Address.
Step 4
When the access points IP address appears in the IP Address field, write it down.
If IPSU reports that the IP address is 10.0.0.1, the default IP address, then the access point did not receive
a DHCP-assigned IP address. Steps for assigning an IP address are included in the Default IP Address
section in Chapter 3 of the Cisco Aironet Access Point Software Configuration Guide.
Step 5
To check the IP address, browse to the access points browser-based management pages. Open an
Internet browser.

OL-0738-02
3-3
Chapter 3
Basic Configuration
Step 6
Type or paste the access points IP address in the browsers location or address field. (If you are using
Netscape, the field is labeled Netsite or Location; if you are using Microsoft Explorer, the field is labeled
Address.)
Step 7
Press Enter. The access points home page appears.
Setting the Access Points IP Address and SSID

If your access point does not receive an IP address from a DHCP server, or if you want to change the
default IP address, you can use IPSU to assign an IP address. You can set the access points SSID at the
same time.
Note
The computer you use to assign an IP address to the access point must have an IP address of its own.
Note
IPSU can change the access points IP address and SSID only from their default settings. After the IP
address and SSID have been changed, IPSU cannot change them again. (For additional information see
Using an Internet Browser or Using a Terminal Emulator sections.)
Follow these steps to assign an IP address and an SSID to the access point:
Step 1
Double-click the IP Setup icon on your computer desktop. (If IPSU is not installed on your computer,
follow the steps in the Obtaining and Installing IPSU section on page 3-3 to install it.)
Step 2
When the utility window opens, make sure Set Parameters is selected in the Function box.
Step 3
Type the access points MAC address in the Device MAC ID field. The access points MAC address is
printed on the label on the bottom of the unit. It should contain six pairs of hexadecimal digits. Your
access points MAC address might look like the following example:
004096xxxxxx
Note
The MAC address field is not case-sensitive.
Step 4
Type the IP address you want to assign to the access point in the IP Address field.
Step 5
Type the SSID you want to assign to the access point in the SSID field.
Note
You cannot set the SSID without also setting the IP address. You can set the IP address without setting
the SSID, however.
Step 6
Click Set Parameters.
Step 7
To test the IP address, open an Internet browser.
3-4
OL-0738-02
Chapter 3
Basic Configuration
Step 8
Type or paste the access points IP address in the browsers location or address field. (If you are using
Netscape, the field is labeled Netsite or Location; if you are using Microsoft Internet Explorer, the field
is labeled Address.)
Step 9
Press Enter. The access points home page appears.

You can open the access points management system through your Internet browser or through the access
points serial port using a terminal emulator. Each method is described below.
Using an Internet Browser

Follow these steps to enter basic settings with an Internet browser:
Step 1
Open an Internet browser.
Step 2
Type or paste the access points IP address in the browsers location field. (If you are using Netscape
Communicator, the field is labeled Netsite or Location; if you are using Microsoft Explorer, the field is
labeled Address.) Press Enter.
Step 3
When the access points Summary Status page appears, click Setup. When the Setup page appears, click
Express Setup.
Note
If the access point is new and its factory configuration has not been changed, the Express Setup
page appears instead of the Summary Status page when you first browse to the access point.
Step 4
Type a system name for the access point in the System Name field. A descriptive system name makes it
easy to identify the access point on your network.
Step 5
Select a configuration server protocol from the Configuration Server Protocol pull-down menu. The
configuration server protocol you select should match your networks method of IP address assignment.
The Configuration Server link takes you to the Boot Server Setup page, which you use to configure the
access point to work with your networks BOOTP or DHCP servers for automatic assignment of IP
addresses.
The Configuration Server Protocol pull-down menu options include:
Step 6
NoneYour network does not have an automatic system for IP address assignment.
BOOTPWith Bootstrap Protocol, IP addresses are hard-coded based on MAC addresses.
DHCPWith Dynamic Host Configuration Protocol, IP addresses are leased for predetermined
periods of time.
Type an IP address in the Default IP address field. If DHCP is not enabled for your network, the IP
address you enter in this field will be the access points static IP address. If DHCP or BOOTP is enabled,
the address you enter in this field provides the IP address only when no server responds with an IP
address for the access point.

OL-0738-02
3-5
Chapter 3
Basic Configuration
Step 7
Enter an IP subnet mask in the Default IP Subnet Mask field to identify the subnetwork so the access
points IP address can be recognized on the LAN. If DHCP or BOOTP is not enabled, this field is the
subnet mask. If DHCP or BOOTP is enabled, this field provides the subnet mask only when no server
responds to the access points DHCP or BOOTP request.
Step 8
Enter the IP address of your default internet gateway in the Default Gateway field. The entry
255.255.255.255 indicates no gateway. Clicking the Gateway link takes you to the Routing Setup page,
which you use to configure the access point to communicate with the IP network routing system.
Step 9
Type an SSID for the access point in the Radio Service Set ID (SSID) field. The SSID is a unique
identifier that client devices use to associate with the access point. The SSID can be any alphanumeric
entry from two to 32 characters long.
Step 10
Select a network role for the access point from the Role in Radio Network pull-down menu. The menu
contains the following options:
Step 11
Step 12
Step 13
Access Point/RootA wireless LAN transceiver that connects an Ethernet network with wireless
client stations. Use this setting if the access point will be connected to the wired LAN.
Repeater/Non-RootAn access point that transfers data between a client and another access point.
Use this setting for access points not connected to the wired LAN.
Client/Non-rootA station with a wireless connection to an access point. Use this setting for
diagnostics, such as when you need to test the access point by having it communicate with another
access point.
Select an Optimize Radio Network For option to assign either preconfigured settings or customized
settings for the access point radio:
ThroughputMaximizes the data volume handled by the access point but might reduce the access
points range.
RangeMaximizes the access points range but might reduce throughput.
CustomThe access point will use the settings you enter on the AP Radio Hardware page. Click
the Custom link to go to the AP Radio Hardware page.
To automatically configure the access point to be compatible with other devices on your wireless LAN,
select an Ensure Compatibility With option:
2-Mbps clientsSelect this setting if your network contains Cisco Aironet devices that operate at 2
Mbps.
non-Aironet 802.11Select this setting if there are non-Cisco Aironet devices on your wireless
LAN.
To use Simplified Network Management Protocol (SNMP), enter a community name in the SNMP
Admin. Community field. This name automatically appears in the list of users authorized to view and
make changes to the access points management system.
Click the SNMP link to go to the SNMP Setup page, where you can edit other SNMP settings.
You can define other SNMP communities with User Management. The Security Setup section in
Chapter 3 of the Cisco Aironet Access Point Software Configuration Guide describes User Management.
Step 14
Click OK. The Setup page appears. If you changed the Role in Radio Network setting, your access point
reboots.
3-6
OL-0738-02
Chapter 3
Basic Configuration
Using a Terminal Emulator

This section provides instructions for Microsofts HyperTerminal; other programs are similar.
Selecting Pages and Settings

When you type names and settings that appear in brackets you jump to that page or setting.
HyperTerminal jumps to the page or setting as soon as it recognizes a unique name, so you need to type
only the first few characters in the page or setting name. To jump from the home page to the Setup page,
for example, you would only need to type se.
Applying Changes to the Configuration

The console interfaces auto-apply feature is on by default, so changes you make to any page are applied
automatically when you move to another management page. To apply changes and stay on the current
page, type apply and press Enter.
Assigning Basic Settings

Follow these steps to assign basic settings to the access point with a terminal emulator:
Step 1
Connect a nine-pin, male-to-female, straight-through serial cable to the COM port on a computer and to
the RS-232 serial port on the back of the access point. Figure 3-1 and Figure 3-2 show the location of
the access points serial port.
Figure 3-1
5VDC
Connecting the Serial Cable for 340 Series and 350 Series Access Points
SERIAL
SERIAL
ETHERN
ET
RS-232
9-pin serial extension
cable to PC COM port

OL-0738-02
3-7
Chapter 3
Basic Configuration
Figure 3-2
Connecting the Serial Cable for 350 Series Metal Case Access Points
IS
S
IE
R
E
S
0 N
5 I
3 O
T P
E S
N S
O CE
IR C
ETHERN
RADIOASSOCIATION ET ACTIVITY
ACTIVITY
STATUS
5VDC
SERIAL PO
RT
LEFT
SERIAL PO
RT
ONLINE
RIGHT/PRI
MARY
POWER
ETHERN
ET
RS-232
9-pin serial extension
cable to PC COM port
Step 2
Open a terminal emulator.
Step 3
Enter these settings for the connection:
Bits per second (baud rate): 9600
Data bits: 8
Parity: No parity
Stop bits: 1
Flow control: Xon/Xoff
Step 4
Press = to display the home page of the access point. If the access point is new and its factory
configuration has not been changed, the Express Setup page appears; if the access point has been
configured, the Summary Status page appears.
Step 5
Press n to select System Name. Type a system name for the access point and press Enter. A descriptive
system name makes it easy to identify the access point on your network.
Step 6
Press t and then press Enter to select Terminal Type. Press t and then press Enter to select teletype
display on the console interface. Press a and then press Enter to select ANSI display on the console
interface.
Step 7
Press pr and then press Enter to select Config Server Protocol. Press n to select none; press b to select
BOOTP; press d to select DHCP. Press Enter after you make your selection.
Step 8
Press ad and then press Enter to select IP Address. Enter an IP address for the access point. If DHCP is
not enabled for your network, the IP address you enter is the access points static IP address. If DHCP
is enabled, the address you enter provides the IP address only when no DHCP server responds with an
IP address for the access point.
Step 9
Press su and then press Enter to select IP Subnet Mask. Enter an IP subnet mask to identify the
subnetwork so the access points IP address can be recognized on the LAN. If DHCP is not enabled, the
subnet you enter is the static subnet mask. If DHCP is enabled, your entry provides the subnet mask only
when no DHCP server responds to the access points DHCP request.
Step 10
Press g and then press Enter to select Default Gateway. Enter the IP address of your default internet
gateway. The entry 255.255.255.255 indicates no gateway.
Step 11
Press ra and then press Enter to select Radio Service Set ID (SSID). Enter an SSID for the access point.
The SSID is a unique identifier that client devices use to associate with the access point. The SSID can
be any alphanumeric entry from two to 32 characters long.
3-8
OL-0738-02
Chapter 3
Basic Configuration
Step 12
Step 13
Step 14
Step 15
Press ro and then press Enter to select Role in Radio Network. The network roles include the following
options:
Access Point/RootPress a and then press Enter to select this setting. A wireless LAN transceiver
that connects an Ethernet network with wireless client stations. Use this setting if the access point
will be connected to the wired LAN.
Repeater/Non-RootPress r and then press Enter to select this setting. An access point that
transfers data between a client and another access point. Use this setting for access points not
connected to the wired LAN.
Client/Non-rootPress c and then press Enter to select this setting. A station with a wireless
connection to an access point. Use this setting for diagnostics, such as when you need to test the
access point by having it communicate with another access point.
Press op and then press Enter to select Optimize Radio Network For. These options assign either
preconfigured settings or customized settings for the access point radio:
ThroughputPress t and then press Enter to select this setting. Maximizes the data volume handled
by the access point but might reduce the access points range.
RangePress r and then press Enter to select this setting. Maximizes the access points range but
might reduce throughput.
CustomPress c and then press Enter to select this setting. The access point will use the settings
you enter on the AP Radio Hardware page. Chapter 3 of the Cisco Aironet Access Point Software
Configuration Guide describes the AP Radio Hardware page.
Use the Ensure Compatibility With setting to automatically configure the access point to be compatible
with other devices on your wireless LAN:
2-Mbps clientsPress 2 and then press Enter to select this setting. Select this setting if your
network contains Cisco Aironet devices that operate at 2 Mbps.
non-Aironet 802.11Press no and then press Enter to select this setting. Select this setting if there
are non-Cisco Aironet devices on your wireless LAN.
Press sn and then press Enter to select SNMP Admin. Community. Enter an SNMP community name.
This name automatically appears in the list of users authorized to view and make changes to the access
points management system.
You can define other SNMP communities with User Management. The Security Setup section in
Chapter 3 of the Cisco Aironet Access Point Software Configuration Guide describes User Management.
Step 16
Press ap and press Enter to apply your basic settings. If you changed the Role in Radio Network setting,
your access point reboots.

OL-0738-02
3-9
Chapter 3
Basic Configuration

Table 3-1 lists the default settings on the access points Express Setup page.
Table 3-1
Default Settings on the Express Setup Page
Setting Name
Default Value
System Name
AIR-AP350_xxxxxx (the last six characters of the

units MAC address)
Terminal Type (on Console interface only)
teletype
Config Server Protocol
DHCP
IP address
10.0.0.1
IP Subnet Mask
255.255.255.0
Default Gateway
255.255.255.255
SSID
tsunami
Role in Radio Network
Access Point/Root
Optimize Radio Network For
Throughput
Ensure Compatibility With
SNMP Admin. Community
admin
3-10
OL-0738-02
C H A P T E R
Troubleshooting
This chapter provides troubleshooting procedures for basic problems with the access point. For the most
up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at
http://www.cisco.com/tac. Select Wireless LAN under Top Issues.
Sections in this chapter include:
Resetting to the Default Configuration

OL-0738-02
4-1
Chapter 4
Troubleshooting

If your access point is not communicating, check the three indicators on the top panel. You can use them
to quickly assess the units status. Figure 4-1 and Figure 4-2 show the indicators, and Table 4-1 lists the
meanings of the indicator signals.
Figure 4-1
Indicators on the 340 Series and 350 Series Access Point

W I R E L E S S AC C E S S P O I N T
Radio
Figure 4-2
49075
Ethernet
Status
Indicators on 350 Series Metal Case Access Points

WIRELESS ACCESS POINT
ETHERNET ACTIVITY
ASSOCIATION STATUS
60511
RADIO ACTIVITY
Ethernet
Status
Radio
The indicators signals have the following meanings:
The Ethernet indicator signals traffic on the wired LAN, or Ethernet infrastructure. This indicator
blinks green when a packet is received or transmitted over the Ethernet infrastructure.
The status indicator signals operational status. Blinking green indicates that the access point is
operating normally but is not associated with any wireless devices. Steady green indicates that the
access point is associated with a wireless client.
For repeater access points, blinking 50% on, 50% off indicates the repeater is not associated with
the root access point; blinking 7/8 on, 1/8 off indicates that the repeater is associated with the root
access point but no client devices are associated with the repeater; steady green indicates that the
repeater is associated with the root access point and client devices are associated with the repeater.
The radio indicator blinks green to indicate radio traffic activity. The light is normally off, but it
blinks green whenever a packet is received or transmitted over the access points radio.
4-2
OL-0738-02
Chapter 4
Troubleshooting
Table 4-1
Top Panel Indicator Signals
Message
type
Ethernet
indicator
Status
indicator
Radio
indicator
Meaning
Association
status
Steady
green
At least one wireless client device is

associated with the unit.
Blinking
green
No client devices are associated; check the

units SSID and WEP settings.
Steady
green
Blinking
green
Transmitting/receiving radio packets
Blinking
green
Steady
green
Transmitting/receiving packets.
Steady
green
Blinking
amber
Maximum retries or buffer full occurred on

the radio.
Blinking
amber
Steady
green
Transmit/receive errors.
Blinking red
Ethernet cable is disconnected (340 series

only).
Blinking
amber
General warning
Failure
Steady red
Steady red
Steady red
Firmware failure; disconnect power from

the unit and reapply power.
Firmware
upgrade
Steady red
Unit is loading new firmware.
Operational
Error/warning

Mismatched basic settings are the most common causes of lost connectivity with wireless clients. If the
access point does not communicate with client devices, check the following settings.
SSID
Wireless clients attempting to associate with the access point must use the same SSID as the access point.
The default SSID is tsunami.
WEP Keys
The WEP key you use to transmit data must be set up exactly the same on your access point and any
wireless devices with which it associates. For example, if you set WEP Key 3 on your wireless LAN
adapter to 0987654321 and select it as the transmit key, you must also set WEP Key 3 on the access point
to exactly the same value. The access point does not need to use Key 3 as its transmit key, however.
Refer to the Security section in Chapter 3 of the Cisco Aironet Access Point Software Configuration
Guide for instructions on setting the access points WEP keys.

OL-0738-02
4-3
Chapter 4
Troubleshooting

If you forget the password that allows you to configure the access point, you might need to completely
reset the configuration. Follow the steps below to delete the current configuration and return all access
point settings to the factory defaults.
Steps for Firmware Versions 11.07 or Later

Follow the steps in this section if your access point is running firmware version 11.07 or later.
Note
The following steps reset all configuration settings to factory defaults, including passwords, WEP keys,
the IP address, and the SSID. If you do not need to reset the entire configuration, use the Configuration
Reset buttons on the System Configuration Setup page in the web-browser interface. Consult the Cisco
Aironet Access Point Software Configuration Guide for more information on the reset buttons in the
web-browser interface.
Step 1
Use a straight-through cable with 9-pin male to 9-pin female connectors to connect the COM 1 or COM
2 port on your computer to the RS-232 port on the access point.
Step 2
Open a terminal-emulation program on your computer.
Note
These instructions describe HyperTeminal; other programs are similar.
Step 3
In the Connection Description window, enter a name and select an icon for the connection and click
OK.
Step 4
In the Connect To window, select the port to which the cable is connected and click OK.
Step 5
In the Port Settings window, enter the following settings:
9600 baud,
8 data bits,
No parity,
1 stop bit, and
Xon/Xoff flow control
Step 6
Click OK, and press Enter.
Step 7
When the Summary Status screen appears, reboot the access point by unplugging the power connector
and then plugging it back in.
Step 8
When the access point reboots and the Summary Status screen reappears, type :resetall, and press Enter.
Step 9
Type yes, and press Enter to confirm the command.
Note
The resetall command is valid for only 2 minutes immediately after the access point reboots. If you do
not enter and confirm the resetall command during that 2 minutes, reboot the access point again.
4-4
OL-0738-02
Chapter 4
Troubleshooting
Step 10
After the access point reboots and the Express Setup screen appears, reconfigure the access point by
using the terminal emulator or an Internet browser.
Steps for Firmware Versions 11.06 or Earlier

Follow the steps in this section if your access point is running firmware version 11.06 or earlier.
Note
The following steps reset all configuration settings to factory defaults, including passwords, WEP keys,
the IP address, and the SSID. If you do not need to reset the entire configuration, use the Configuration
Reset buttons on the System Configuration Setup page in the web-browser interface. Consult the Cisco
Aironet Access Point Software Configuration Guide for more information on the reset buttons in the
web-browser interface.
Determining the Boot-Block Version

The steps you follow to reconfigure the access point depend on the version of the access points boot
block. Follow these steps to find out which boot block version is on your access point:
Step 1
Open a Telnet session to the access point.
Note
You can also use these instructions while communicating with the access point through the
console port or with an SNMP manager. Skip to Step 3 if you use an SNMP manager.
Step 2
Type :cmd and press Enter to switch from text-browser mode to SNMP mode.
Step 3
Type bootblockVersion and press Enter. Text appears with information about the system. If your access
points boot block version is 1.01, the text might look like this:
OID: iso.org.dod.internet.private.enterprises.aironet.awcVx.awcSystem.
bootblockVersion
Value [RO]: 1.01
Step 4
Type exit and press Enter to return to text-browser mode.
Step 5
If your boot block version is 1.01 or earlier, follow the instructions in the Reconfiguration Steps for
Boot Block Version 1.01 or Earlier section on page 4-6. If your boot block version is 1.02 or later,
follow the instructions in the Reconfiguration Steps for Boot Block Version 1.02 or Later section on
page 4-7.

OL-0738-02
4-5
Chapter 4
Troubleshooting
Reconfiguration Steps for Boot Block Version 1.01 or Earlier

Follow these steps to reconfigure your access point if the boot block version on your access point is
version 1.01 or earlier and the firmware version on your access point is 11.06 or earlier. To find which
boot block version is on your access point, follow the steps in the Determining the Boot-Block Version
section on page 4-5.
Caution
Failure to follow these instructions correctly can result in a nonoperational access point that must be
returned to the factory. If your access point stops working after you attempt this procedure, contact Cisco
TAC for assistance.
Step 1
Step 2
Note
Step 3
OK.
Step 4
Step 5
In the Port Settings window, make the following settings: 9600 baud, 8 data bits, No parity, 1 stop bit,
and Xon/Xoff flow control.
Step 6
Click OK and press Enter three times.
Step 7
When the Summary Status screen appears, reboot the access point by unplugging the power connector
and then plugging it back in, or by pressing Ctrl-X.
Step 8
When the message Type <esc> within 5 seconds for menu appears, press Esc.
Step 9
Write down the list of files for future reference.
Caution
Perform the next six steps carefully to avoid accidentally deleting the installation key files or the
firmware files. You must carefully note the file selection letters, because they change during the
following steps. If you forget to copy the access points installation key file to DRAM in Step 10, or if
you do not copy it back to configuration memory in Step 13, your access point will stop functioning.
Step 10
Copy the access points installation key file to the access points DRAM by pressing c to select Copy
file, then 1 to select DRAM, then the selection letter for the file called AP Installation Key.
Step 11
If the list of configuration files contains a file called VAR Installation Key, copy that file to DRAM along
with the AP Installation Key. Copy the VAR installation key file to DRAM by pressing c to select Copy
file, then 1 to select DRAM, then the selection letter for the file called VAR Installation Key.
Caution
Step 12
Make sure you select the Configuration memory bank for formatting in Step 12. If you accidentally
format a different memory bank your access point will stop functioning.
Reformat the access points configuration memory bank by pressing ! to select FORMAT memory
bank, then 2 to select Config, then upper-case Y to confirm the FORMAT command.
4-6
OL-0738-02
Chapter 4
Troubleshooting
Step 13
Copy the installation key back to the configuration memory bank by pressing c to select Copy file, then
2 to select Config, then the selection letter for the AP Installation Key.
Step 14
If you copied a VAR installation key to DRAM in Step 11, copy it back to the configuration memory
bank by pressing c to select Copy file, then 2 to select Config, then the selection letter for the file VAR
Installation Key. If the access point does not have a VAR installation key file, skip to Step 15.
Step 15
Run the access point firmware by pressing r to select Run, then the selection letter for the firmware file
which is displayed. The message Inflating [firmware file name] appears while the access point starts
the firmware.
Step 16
When the Express Setup screen appears, begin reconfiguring the access point using the terminal
emulator or an Internet browser.
Reconfiguration Steps for Boot Block Version 1.02 or Later

Follow these steps to reconfigure your access point if the boot block version on your access point is
version 1.02 or later and the firmware version on your access point is 11.06 or earlier. To find which boot
block version is on your access point, follow the steps in the Determining the Boot-Block Version
section on page 4-5.
Caution
Failure to follow these instructions correctly can result in a nonoperational access point that must be
returned to the factory. If your access point stops working after you attempt this procedure, contact Cisco
TAC for assistance.
Step 1
Step 2
Note
Step 3
OK.
Step 4
Step 5
In the Port Settings window, make the following settings: 9600 baud, 8 data bits, No parity, 1 stop bit,
and Xon/Xoff flow control.
Step 6
Click OK and press Enter.
Step 7
When the Summary Status screen appears, reboot the access point by pressing Ctrl-X or by unplugging
the power connector and then plugging it back in.
Step 8
When the memory files are listed under the heading Memory:File, press Ctrl-W within 5 seconds to
reach the boot block menu.

OL-0738-02
4-7
Chapter 4
Troubleshooting
Step 9
Caution
Write down the list of files for future reference.
Perform the next six steps carefully to avoid accidently deleting the installation key files or the firmware
files. You must carefully note the file selection letters, because they change during the following steps.
If you forget to copy the access points installation key file to DRAM in Step 10, or if you do not copy
it back to configuration memory in Step 13, your access point will stop functioning.
Step 10
Copy the access points AP Installation Key to the access points DRAM by pressing c to select Copy
file, then 1 to select DRAM, then the selection letter for the file AP Installation Key.
Step 11
If the list of configuration files contains a file called VAR Installation Key, you must copy that file to
DRAM along with the AP Installation Key file. If the access point does not have a VAR installation key
file, skip to Step 12.
Caution
If you forget to copy the access points VAR installation key file to DRAM in Step 11, or if you do not
copy it back to configuration memory in Step 14, your access point will stop functioning.
Copy the VAR Installation Key to DRAM by pressing c to select Copy file, then 1 to select DRAM, then
the selection letter for the file VAR Installation Key.
Step 12
Caution
Reformat the access points configuration memory bank by pressing Ctrl-Z to reach the reformat menu.
When the menu appears, press ! to select FORMAT memory bank, then 2 to select Config, then
upper-case Y to confirm the FORMAT command.
Make sure you select the Configuration memory bank for formatting. If you accidentally format a
different memory bank your access point will stop functioning.
Step 13
Copy the installation key back to the configuration memory bank by pressing c to select Copy file, then
2 to select Config, then the selection letter for the file AP Installation Key.
Step 14
If you copied a VAR installation key to DRAM in Step 11, copy it back to the configuration memory
bank by pressing c to select Copy file, then 2 to select Config, then the selection letter for the file VAR
Installation Key. If the access point does not have a VAR installation key file, skip to Step 15.
Step 15
Run the access point firmware by pressing r to select Run, then the selection letter for the firmware file
that is displayed. The message Inflating [firmware file name] appears while the access point starts the
firmware.
Step 16
When the Express Setup screen appears, begin reconfiguring the access point using the terminal
emulator or an Internet browser.
4-8
OL-0738-02
A P P E N D I X

This appendix provides translations of the safety warnings that appear in this publication. These
translated warnings apply to other documents in which they appear in English.

OL-0738-02
A-1
Appendix A

Warning
Do not operate your wireless network device near unshielded

blasting caps or in an explosive environment unless the device
has been modified to be especially qualified for such use.

Waarschuwing
Gebruik dit draadloos netwerkapparaat alleen in de buurt van

onbeschermde ontstekers of in een omgeving met explosieven
indien het apparaat speciaal is aangepast om aan de eisen voor
een dergelijk gebruik te voldoen.
Varoitus
l kyt johdotonta verkkolaitetta suojaamattomien

rjytysnallien lheisyydess tai rjytysalueella, jos laitetta ei
ole erityisesti muunnettu sopivaksi sellaiseen kyttn.oen.
Attention
Ne jamais utiliser un quipement de rseau sans fil proximit

d'un dtonateur non blind ou dans un lieu prsentant des risques
d'explosion, sauf si l'quipement a t modifi cet effet.
Warnung
Benutzen Sie Ihr drahtloses Netzwerkgert nicht in der Nhe

ungeschtzter Sprengkapseln oder anderer explosiver Stoffe, es
sei denn, Ihr Gert wurde eigens fr diesen Gebrauch modifiziert
und bestimmt.
Avvertenza
Advarsel
Non utilizzare la periferica di rete senza fili in prossimit di un

detonatore non protetto o di esplosivi a meno che la periferica
non sia stata modificata a tale proposito.
Ikke bruk den trdlse nettverksenheten nrt inntil uisolerte
fenghetter eller i et eksplosivt milj med mindre enheten er
modifisert slik at den tler slik bruk.
Aviso
No opere o dispositivo de rede sem fios perto de cpsulas

explosivas no protegidas ou num ambiente explosivo, a no ser
que o dispositivo tenha sido modificado para se qualificar
especialmente para essa utilizao.
Advertencia!
No utilizar un aparato de la red sin cable cerca de un detonador

que no est protegido ni tampoco en un entorno explosivo a
menos que el aparato haya sido modificado con ese fin.
Varning!
Anvnd inte den trdlsa ntverksenheten i nrheten av

oskyddade tndhattar eller i en explosiv milj om inte enheten
modifierats fr att kunna anvndas i sdana sammanhang.
A-2
OL-0738-02
Appendix A


Warning
Waarschuwing
Varoitus
Do not work on the system or connect or disconnect cables

during periods of lightning activity.
Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan
het systeem te werken of kabels aan te sluiten of te ontkoppelen.
l tyskentele jrjestelmn parissa lk yhdist tai irrota
kaapeleita ukkosilmalla.
Attention
Ne pas travailler sur le systme ni brancher ou dbrancher les

cbles pendant un orage.
Warnung
Arbeiten Sie nicht am System und schlieen Sie keine Kabel an

bzw. trennen Sie keine ab, wenn es gewittert.
Avvertenza
Advarsel
Aviso
Non lavorare sul sistema o collegare oppure scollegare i cavi

durante un temporale con fulmini.
Utfr aldri arbeid p systemet, eller koble kabler til eller fra
systemet nr det tordner eller lyner.
No trabalhe no sistema ou ligue e desligue cabos durante
perodos de mau tempo (trovoada).
Advertencia!
No operar el sistema ni conectar o desconectar cables durante

el transcurso de descargas elctricas en la atmsfera.
Varning!
Vid ska skall du aldrig utfra arbete p systemet eller ansluta

eller koppla loss kablar.
Installation Warning
Warning
Waarschuwing
Varoitus
Read the installation instructions before you connect the system

to its power source.
Raadpleeg de installatie-aanwijzingen voordat u het systeem
met de voeding verbindt.
Lue asennusohjeet ennen jrjestelmn yhdistmist
virtalhteeseen.

OL-0738-02
A-3
Appendix A
Attention
Avant de brancher le systme sur la source d'alimentation,

consulter les directives d'installation.
Warnung
Lesen Sie die Installationsanweisungen, bevor Sie das System

an die Stromquelle anschlieen.
Avvertenza
Advarsel
Aviso
Advertencia!
Varning!
Consultare le istruzioni di installazione prima di collegare il

sistema allalimentatore.
Les installasjonsinstruksjonene fr systemet kobles til
strmkilden.
Leia as instrues de instalao antes de ligar o sistema sua
fonte de energia.
Ver las instrucciones de instalacin antes de conectar el sistema
a la red de alimentacin.
Ls installationsanvisningarna innan du kopplar systemet till
dess strmfrsrjningsenhet.

Warning
This product relies on the buildings installation for short-circuit

(overcurrent) protection. Ensure that a fuse or circuit breaker no
larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used
on the phase conductors (all current-carrying conductors).
Waarschuwing
Dit produkt is afhankelijk van de installatie van het gebouw voor

kortsluit- (overstroom)beveiliging. Controleer of er een zekering
of stroomverbreker van niet meer dan 120 Volt wisselstroom, 15 A
voor de V.S. (240 Volt wisselstroom, 10 A internationaal) gebruikt
wordt op de fasegeleiders (alle geleiders die stroom voeren).
Varoitus
Tm tuote on riippuvainen rakennukseen asennetusta

oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, ett
vaihevirtajohtimissa (kaikissa virroitetuissa johtimissa)
kytetn Yhdysvalloissa alle 120 voltin, 15 ampeerin ja monissa
muissa maissa 240 voltin, 10 ampeerin sulaketta tai
suojakytkint.
Attention
Pour ce qui est de la protection contre les courts-circuits

(surtension), ce produit dpend de l'installation lectrique du
local. Vrifier qu'un fusible ou qu'un disjoncteur de 120 V alt.,
15 A U.S. maximum (240 V alt., 10 A international) est utilis sur
les conducteurs de phase (conducteurs de charge).
A-4
OL-0738-02
Appendix A

Warnung
Avvertenza
Dieses Produkt ist darauf angewiesen, da im Gebude ein

Kurzschlu- bzw. berstromschutz installiert ist. Stellen Sie
sicher, da eine Sicherung oder ein Unterbrecher von nicht mehr
als 240 V Wechselstrom, 10 A (bzw. in den USA 120 V
Wechselstrom, 15 A) an den Phasenleitern (allen stromfhrenden
Leitern) verwendet wird.
Questo prodotto dipende dallinstallazione delledificio per
quanto riguarda la protezione contro cortocircuiti
(sovracorrente). Verificare che un fusibile o interruttore
automatico, non superiore a 120 VCA, 15 A U.S. (240 VCA, 10 A
internazionale) sia stato usato nei fili di fase (tutti i conduttori
portatori di corrente).
Advarsel
Dette produktet er avhengig av bygningens installasjoner av

kortslutningsbeskyttelse (overstrm). Kontroller at det brukes en
sikring eller strmbryter som ikke er strre enn 120 VAC, 15 A
(USA) (240 VAC, 10 A internasjonalt) p faselederne (alle
strmfrende ledere).
Aviso
Este produto depende das instalaes existentes para proteco

contra curto-circuito (sobrecarga). Assegure-se de que um
fusvel ou disjuntor no superior a 240 VAC, 10A utilizado nos
condutores de fase (todos os condutores de transporte de
corrente).
Advertencia!
Este equipo utiliza el sistema de proteccin contra cortocircuitos

(o sobrecorrientes) del propio edificio. Asegurarse de que se
utiliza un fusible o interruptor automtico de no ms de
240 voltios en corriente alterna (VAC), 10 amperios del estndar
internacional (120 VAC, 15 amperios del estndar USA) en los
hilos de fase (todos aqullos portadores de corriente).
Varning!
Denna produkt r beroende av i byggnaden installerat

kortslutningsskydd (verstrmsskydd). Kontrollera att skring
eller verspnningsskydd anvnds p fasledarna (samtliga
strmfrande ledare) fr internationellt bruk max. 240 V
vxelstrm, 10 A (i USA max. 120 V vxelstrm, 15 A).

OL-0738-02
A-5
Appendix A

Warning
The Cisco Aironet power injector is designed for use with Cisco
Aironet 350 series access points and 350 series wireless bridges
only. Using the power injector with other Ethernet-ready devices
can damage the equipment.
Waarschuwing
De stroominjector van Cisco Aironet is uitsluitend ontworpen

voor gebruik met toegangspunten en draadloze bruggen van de
350-serie van Ciso Aironet. Als u de stroominjector gebruikt met
andere apparaten die geschikt zijn voor gebruik met het Ethernet,
kunt u de apparatuur beschadigen.
Varoitus
Cisco Aironet Power Injector on suunniteltu kytettvksi

ainoastaan Cisco Aironet 350 -sarjan access point -tukiasemien
sek 350-sarjan langattomien siltojen kanssa.
Jnnitteensyttyksikn kyttminen muiden
Ethernet-valmiiden laitteiden kanssa voi vahingoittaa laitteistoa.
Attention
Linjecteur dalimentation en ligne Cisco Aironet a t conu pour

tre utilis uniquement avec des points daccs et des ponts sans
fil Cisco Aironet 350. Lutilisation de linjecteur avec dautres
priphriques compatibles Ethernet risque dendommager
lappareil.
Warnung
Die Cisco Aironet-Einspeiseweiche sollte nur mit den

Zugangspunkten der Cisco Aironet 350-Serie und den drahtlosen
Bridges der 350-Serie verwendet werden. Die Verwendung der
Einspeiseweiche mit anderen Ethernet-fhigen Gerten kann zu
Schden am Gert fhren.
Avvertenza
Il dispositivo per lalimentazione di Cisco Aironet ideato per

lutilizzo esclusivo con punti di accesso e bridge wireless Cisco
Aironet 350 Series. Lutilizzo del dispositivo di alimentazione con
altri dispositivi Ethernet potrebbe danneggiare
lapparecchiatura.
Advarsel
Cisco Aironet Power Injector er bare utviklet for bruk sammen

med Cisco Aironet 350-serien av tilgangspunkter og 350-serien av
trdlse broer. Bruk av strmforsyningen med andre
Ethernet-forberedte enheter kan skade utstyret.
Aviso
O injector de potncia da Cisco Aironet foi concebido para

utilizao exclusiva com os pontos de acesso 350 Series e as
pontes sem fios 350 Series da Cisco Aironet. A utilizao do
injector de potncia com outros dispositivos preparados para a
Ethernet pode danificar o equipamento.
A-6
OL-0738-02
Appendix A

Advertencia!
Varning!
El dispositivo de alimentacin Aironet de Cisco est diseado

para ser utilizado nicamente con puntos de acceso y puentes
inalmbricos de la serie Aironet 350 de Cisco. Si se utiliza con
otros dispositivos para Ethernet, el equipo puede daarse.
Cisco Aironets strmfrsrjningsenhet r utformad fr att endast
anvndas med Cisco Aironets tkomstpunkter ur 350-serien och
trdlsa bryggor ur 350-serien. Om du anvnder enheten med
ngot annat Ethernet-anpassat hjlpmedel kan utrustningen
skadas.

OL-0738-02
A-7
Appendix A
A-8
OL-0738-02
A P P E N D I X
Declarations of Conformity and Regulatory

Information
This appendix provides declarations of conformity and regulatory information for Cisco Aironet access
points.
This appendix contains the following sections:
Department of Communications Canada
European Community, Switzerland, Norway, Iceland, and Liechtenstein

OL-0738-02
B-1
Appendix B
Manufacturers Federal Communication Commission

Declaration of Conformity Statement
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Models:
AIR-AP340, AIR-AP341, AIR-AP342, AIR-AP352
FCC Certification number:
LDK102035 (AIR-AP34x),
LDK102040 (AIR-AP35x)
Manufacturer:
Cisco Systems, Inc.
San Jose, CA 95134-1706
USA
This device complies with Part 15 rules. Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. This equipment generates,
uses, and radiates radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference. However, there is no guarantee that interference will not
occur. If this equipment does cause interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to correct the interference by one of the
following measures:
Caution
Reorient or relocate the receiving antenna.
Increase separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from which the receiver is connected.
Consult the dealer or an experienced radio/TV technician.
The Part 15 radio device operates on a non-interference basis with other devices operating at this
frequency. Any changes or modification to said product not expressly approved by Cisco could void the
users authority to operate this device.
B-2
OL-0738-02
Appendix B


Canadian Compliance Statement
This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du
Canada.
This device complies with Class B Limits of Industry Canada. Operation is subject to the following two
conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired
operation.
The device is certified to the requirements of RSS-139-1 and RSS-210 for 2.4-GHz spread spectrum
devices. The use of this device in a system operating either partially or completely outdoors may require
the user to obtain a license for the system according to the Canadian regulations. For further information,
contact your local Industry Canada office.

OL-0738-02
B-3
Appendix B
European Community, Switzerland, Norway, Iceland, and Liechtenstein
European Community, Switzerland, Norway, Iceland, and

Liechtenstein
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC
English:
This equipment is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Deutsch:
Dieses Gert entspricht den grundlegenden Anforderungen und den weiteren

entsprecheneden Vorgaben der Richtlinie 1999/5/EU.
Dansk:
Dette udstyr er i overensstemmelse med de vsentlige krav og andre relevante

bestemmelser i Directiv 1999/5/EF.
Espaol:
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de
la Directive 1999/5/EC.

1999/5/E.
Franais:
Cet appareil est conforme aux exigencies essentialles et aux autres dispositions
pertinantes de la Directive 1999/5/EC.
slenska:
essi bnaur samrmist lgbonum krfum og rum kvum tilskipunar

1999/5/ESB.
Italiano:
Questo apparato conforme ai requisiti essenziali ed agli altri principi sanciti dalla
Direttiva 1999/5/EC.
Nederlands:
Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van

richtlijn 1999/5/EC.
Norsk:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante

bestemmelser i EU-directiv 1999/5/EC.
Portugus:
Este equipamento satisfaz os requisitos essenciais e outras provises da Directiva

1999/5/EC.
Suomalainen:
Tm laite tytt direktiivin 1999/5/EY oleelliset vaatimukset ja on siin asetettujen

muidenkin ehtojen mukainen.
Svenska:
Denna utrustning r i verensstmmelse med de vsentliga kraven och andra relevanta

bestmmelser i Direktiv 1999/5/EC.
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
B-4
OL-0738-02
Appendix B

The Declaration of Conformity related to this product can be found at the following URL:
http://www.ciscofax.com
For the 340 series, the following standards were applied:
Radio: ETS 300.328
EMC: ETS 300.826
Safety: EN 60950
49325
The following CE mark is affixed to the 340 series equipment:
For the 350 series, the following standards were applied:
Radio: EN 300.328-1, EN 300.328-2
EMC: EN 301 489-1, EN 301 489-17
Safety: EN 60950
54613
The following CE mark is affixed to the 350 series equipment:
The above CE mark is required as of April 8, 2000 but might change in the future
Note
This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to
certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate
Compliance.
Note
Combinations of power levels and antennas resulting in a radiated power level of above 100 mW eirp are
considered as not compliant with the above mentioned directive and are not allowed for use within the
European community and countries that have adopted the European R&TTE directive 1999/5/EC and/or
the CEPT recommendation Rec 70.03. For more details on legal combinations of power levels and
antennas, contact Cisco Corporate Compliance.

The radio module has been evaluated under FCC Bulletin OET 65C and found compliant to the
requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure
from radio frequency devices.

OL-0738-02
B-5
Appendix B
Guidelines for Operating Cisco Aironet Access Points and

Bridges in Japan
This section provides guidelines for avoiding interference when operating Cisco Aironet access points
and bridges in Japan. These guidelines are provided in both Japanese and English.
03-5549-6500
43768
Japanese Translation
English Translation
This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices
such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio
stations and unlicensed specified low-power radio stations) used in factory production lines.
1.
Before using this equipment, make sure that no premises radio stations or specified low-power radio
stations of RF-ID are used in the vicinity.
2.
If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the
frequency or stop using the device; contact the number below and ask for recommendations on
avoiding radio interference, such as setting partitions.
3.
If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact
the number below.
Contact Number: 03-5549-6500
B-6
OL-0738-02
Appendix B


All the Declaration of Conformity statements related to this product can be found at the following URL:
http://www.ciscofax.com
Declaration of Conformity Statement for European Union Countries

The Declaration of Conformity statement for the European Union countries is listed below:

OL-0738-02
B-7
Appendix B
B-8
OL-0738-02
INDEX
conventions, document
viii
coverage
access point/root
antenna
3-6, 3-9
minimal overlap
1-2
multiple overlapping networks
antenna connector
audience
2-4
1-9
vii
D
data rates
1-8, 2-5
declarations of conformity
basic settings
checking
3-10
entering
B-1
default configuration, resetting

4-3
default
3-5, 3-7
boot block version

BOOTP
2-4
default gateway
3-6, 3-8
default settings
3-10
DHCP
4-5
4-4
3-2, 3-5, 3-8
documentation
3-5, 3-8
conventions
viii
related publications
viii
C
cautions
2-2
CD-ROM
2-6
CE mark
ensure compatibility setting
B-5
environmental conditions
central unit
1-7
ET Docket 96-8
Cisco TAC
4-1
Ethernet indicator
client/non-root
compliance
3-6, 3-9
1-9
configuration
basic
3-6, 3-9
2-5
2-2
4-2
Ethernet port
1-3
express setup
3-2, 3-5
extended temperature range
1-8, 2-3
3-1
server
3-5, 3-8
summary
3-2
connecting cables
340 series
2-7
350 series
2-8
connectors
F
FCC
2-2, B-2
frequency range
1-8
1-8

OL-0738-02
IN-1
Index
power
340 series
indicators
1-4, 4-2
350 series options
information packet
inline power
2-6
adapter
1-2
2-3
injector
3-5
IPSU
2-7
2-8
inline (350 series)
IP address, finding and setting
3-3
3-2
output
1-2
1-8
power injector
2-8
2-6
connecting
installation guidelines
Internet browser
2-7
2-6
LAN transceiver
1-1
R&TTE
LED indicators
Ethernet
status
radio indicator
4-2
radio traffic
B-4
4-2
radio specifications
4-2
range
4-2
1-8
1-8, 3-6, 3-9
regulatory
1-9, B-1
related publications
repeater/non-root
M
MAC
viii
3-6, 3-9
repeater operation
RF exposure
3-3, 3-4
metal case
modulation
roaming
1-4, 1-8, 4-2
B-5
2-4, 2-5
role, radio network
1-8
1-6
root unit
3-6, 3-9, 3-10
1-5
N
network configurations
1-5
S
safety warnings, translated
seamless roaming
A-1
2-4
serial
optimize radio network

overview
3-6, 3-9
cable
2-6
connecting cable
1-1
port
1-3
site survey
size
package contents
password reset
3-6, 3-9, 3-10
specifications
4-4
ports, Ethernet and serial
2-5
1-8
SNMP
2-6
1-3
SSID
3-2, 3-7
1-8
3-2, 3-6, 3-8, 3-10, 4-3
IN-2
OL-0738-02
Index
status indicators
1-8, 4-2
subnet mask
3-6, 3-8
system name
3-10
T
TAC
4-1
temperature range
1-8
terminal emulator
3-2, 3-7
terminal type
throughput
3-10
3-6, 3-9
troubleshooting
4-1
U
unpacking
2-6
V
voltage range
1-8
W
warnings
2-2
warnings, translated safety
A-1
web site
Cisco Software Center
weight
3-3
1-8
WEP key
4-3

OL-0738-02
IN-3
Index
IN-4
OL-0738-02

Cisco Aironet 350 340 AP350higp

Uploaded by

Copyright:

Available Formats

Cisco Aironet 350 340 AP350higp

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cisco Aironet 350 340 AP350higp

Uploaded by

Copyright:

Available Formats

Cisco Aironet Access Point

Hardware Installation Guide

Text Part Number: OL-0738-02

Cisco Aironet Access Point Hardware Installation Guide

Obtaining Technical Assistance x

Key Features 1-2

Cautions and Warnings

Cisco Aironet Access Point Hardware Installation Guide

Installation Guidelines 2-3

Unpacking the Access Point 2-6

Using the IP Setup Utility 3-2

Summary of Configuration Steps

Checking the Top Panel Indicators

Resetting to the Default Configuration 4-4

Cisco Aironet Access Point Hardware Installation Guide

Reconfiguration Steps for Boot Block Version 1.01 or Earlier 4-6

Translated Safety Warnings

Explosive Device Proximity Warning

Circuit Breaker (15A) Warning

Declarations of Conformity and Regulatory Information

Manufacturers Federal Communication Commission Declaration of Conformity Statement

Department of Communications Canada B-3

Declaration of Conformity Statement for European Union Countries

Cisco Aironet Access Point Hardware Installation Guide

Cisco Aironet Access Point Hardware Installation Guide

Cisco Aironet Access Point Hardware Installation Guide

Commands and keywords are in boldface type.

Cisco Aironet Access Point Hardware Installation Guide

Cisco Aironet Access Point Hardware Installation Guide

Obtaining Technical Assistance

Cisco TAC Website

Opening a TAC Case

TAC Case Priority Definitions

Cisco Aironet Access Point Hardware Installation Guide

Obtaining Additional Publications and Information

Cisco Aironet Access Point Hardware Installation Guide

Cisco Aironet Access Point Hardware Installation Guide

Network configuration examples

Access point specifications

Cisco Aironet Access Point Hardware Installation Guide

Ethernet and serial ports

A Cisco Aironet power injector

Cisco Aironet Access Point Hardware Installation Guide

Ethernet and Serial Ports

Cisco Aironet Access Point Hardware Installation Guide

Indicators on the 340 and 350 Series Access Point

CISCO AIRONET 350 SERIES

Indicators on the 350 Series Metal Case Access Point

CISCO AIRONET 350 SERIES

Cisco Aironet Access Point Hardware Installation Guide

Network Configuration Examples

Root Unit on a Wired LAN

Access Points as Root Units on a Wired LAN

Cisco Aironet Access Point Hardware Installation Guide

Network Configuration Examples

Repeater Unit That Extends Wireless Range

Access Point as Repeater

Cisco Aironet Access Point Hardware Installation Guide

Central Unit in an All-Wireless Network

Access Point as Central Unit in All-Wireless Network