Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
685 views

Distributed Control System Assignment

Distributed control systems (DCS) are used to control complex, continuous processes across various industries. A DCS consists of distributed controllers throughout a system that are connected by a network for communication and monitoring. Each controller monitors and controls its local sub-system. Information is transmitted between controllers and to a central human-machine interface to oversee the entire process. DCS are commonly used in applications like power plants, oil refineries, chemical plants, and other industrial processes requiring distributed, real-time monitoring and control.

Uploaded by

Ghulam Mustaqeem
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
685 views

Distributed Control System Assignment

Distributed control systems (DCS) are used to control complex, continuous processes across various industries. A DCS consists of distributed controllers throughout a system that are connected by a network for communication and monitoring. Each controller monitors and controls its local sub-system. Information is transmitted between controllers and to a central human-machine interface to oversee the entire process. DCS are commonly used in applications like power plants, oil refineries, chemical plants, and other industrial processes requiring distributed, real-time monitoring and control.

Uploaded by

Ghulam Mustaqeem
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 11

Distributed

Control
System
(DCS)
SUBMITTED BY WASEEM SANGI
IN RESPECT OF
FARUKH HABIB

Distributed Control System (DCS)


Introduction
A distributed control system (DCS) refers to a control system usually of a manufacturing system,
process or any kind of dynamic system, in which the controller elements are not central in
location (like the brain) but are distributed throughout the system with each component subsystem controlled by one or more controllers. The entire system of controllers is connected by
networks for communication and monitoring. DCS is a very broad term used in a variety of
industries, to monitor and control distributed equipment.
A DCS typically uses custom designed processors as controllers and uses both proprietary
interconnections and communications protocol for communication. Input and output modules
form component parts of the DCS. The processor receives information from input modules and
sends information to output modules. The input modules receive information from input
instruments in the process (or field) and transmit instructions to the output instruments in the
field. Computer buses or electrical buses connect the processor and modules through multiplexer
or demultiplexers. Buses also connect the distributed controllers with the central controller and
finally to the Humanmachine interface (HMI) or control consoles.
Architecture:

CPU:
CPU CARD:

There are two models of CPU card: The CP701 for basic systems and CP 703 for enhanced
systems. The basic system model has 8 MB of memory, while the enhanced system model has 16
MB. The model chosen depends on the type of system software used. The main memory is
ensured of high reliability by error correction code (ECC).
The redundancy architecture of the CPU is referred to as a synchronous hot standby system,
which is the fundamentally the same as that of the CENTUM CS, the only difference being the
addition of the new error detection and protection functions. These functions set write protected
areas in each CPU card to protect the program and database areas against illegal address writing
instruction from the other CPU card, and thereby prevents both card from failing due to illegal
accesses caused by malfunctions in MPU. Other newly added functions include the memory
management unit (MMU) and write protection which ensure data integrity, the parity check of
addresses and data, the ECC memory, and a two wire signal self checker.
Power Supply Card:
The power supply card is designed to supply power to the common nests, such as the CPU cards,
and up to five I/O module nests. Standardizing the output voltages to +5 V DC has simplified the
circuit and structure and reduced the number of parts. This allowed a power-factor Improvement

unit to be built in so as to comply with the aforementioned EN61000-3-2, class A standard


(relating to power line harmonics). The +5V DC outputs from the two power supply cards pass
through diodes so that they can be coupled externally for redundancy purposes.
The input-voltage monitoring signal (AC ready) and output-voltage monitoring signal (DC
ready) together with the guaranteed retention time of the +5V DC output, enable to control to
continue over a temporary power failure. The output voltage retention time immediately after a
power failure is clearly defined in the specifications since it is closely related to the software
saving process in the CPU card.
Nest Configuration:
The FCS nest is composed of VL Net couplers, battery units for backing up the CPUs main
memory, a backboard, a power distribution board, and a ready signal output unit in addition to
the CPU cards and power supply card. A FCS model has five I/O modules nest.

Input & Output Modules:


The I/O modules convert the analog or digital signals from the field equipment then pass to field
control stations or vice versa to convert the signals from the field control station to the signals for
the field equipment. The I/O module can be categorized into the following seven main types Analog I/O module
Multipoint control analog I/O module
Relay I/O module
Multiplexer module
Digital I/O module
Communication module
Communication card

Analog Input Module

Wiring of Analog I/O Module:


Models AAM10, AAM11, AAM11B, AAM21, AAM21J, APM11, AAM50, AAM51

If output signal between 1 - 5V DC needs to be output to a recorder, etc., connect the Model
AKB301 cable to the (CN1) connector. For example, to output signal from the terminal block
TE16 to the recorder, connect cable Model AKB301 between CN1 and the terminal block.

The digital I/O module is configured by the card unit and either the terminal unit or connector
unit. It inputs and outputs 16 or 32 signal points and converts signals. Since the types or I/O
signals are software-set, no control switch or knob is found on this module.
The table below shows the types of digital I/O modules.

Wiring of Digital I/O Module (Connector Type):


Digital I/O module (connector type)
Models ADM11C, ADM12C, ADM51C, ADM52C

Communication Cards:
The communication cards are used to realize the general-purpose communication of field control
station and subsystems via serial links, so that the subsystem may be controlled or monitored.

Different from the above mentioned cards, the communication package with subsystems is
prepared for ACM21 and ACM22 so that the general-purpose communication may be
conveniently realized. The ACM71 Ethernet communication module receives/sends data from/to
subsystems such as MELSEC via Ethernet.
HIS Operation And Monitoring Windows:
There are different operational and monitoring windows, which have to define during designing
Human Interface Station (HIS).The different windows are shown below:

How the HIS looks like:


The human interface system programmed for a project/plan is designed in such a way that it
would be easy for the operator to understand all the operations occurred in the plant. The
example of visualization of a reactor control power plant has been given below:

Applications:
A typical DCS consists of functionally and/or geographically distributed digital controllers
capable of executing from 1 to 256 or more regulatory control loops in one control box. The
input/output devices (I/O) can be integral with the controller or located remotely via a field
network. Todays controllers have extensive computational capabilities and, in addition to
proportional, integral, and derivative (PID) control, can generally perform logic and sequential
control. Modern DCSs also support neural networks and fuzzy application.
DCSs may employ one or more workstations and can be configured at the workstation or by an
off-line personal computer. Local communication is handled by a control network with
transmission over twisted pair, coaxial, or fiber optic cable. A server and/or applications
processor may be included in the system for extra computational, data collection, and reporting
capability.
Distributed control systems (DCSs) are dedicated systems used to control manufacturing
processes that are continuous or batch-oriented, such as
1) Electrical power grids and electrical generation plants
2) Environmental control systems
3) Traffic signals
4) Radio signals
5) Water management systems
6) Oil refining plants
7) Metallurgical process plants

8) Chemical plants
9) Pharmaceutical manufacturing
10) Sensor networks
11) Dry cargo and bulk oil carrier ships etc.

You might also like