Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 455 views

    S103C E - Magnetici Flowmter CH2200 - 2500 Flanged Pipe

    Uploaded by

    Adam Samy
    The CH 2200 EL and CH 2500 EL sensors represent the state of the art for water cycle and process applications. They feature an extremely wide measurement range of more than 1:1000 without linearization software. This allows for very accurate measurements over a wide flow rate range, including lower flow rates previously too small to measure. The sensors operate using the Faraday principle where a conductor in a magnetic field generates a voltage perpendicular to the field.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    S103C E - Magnetici Flowmter CH2200 - 2500 Flanged Pipe

    Uploaded by

    Adam Samy
    455 views7 pages
    The CH 2200 EL and CH 2500 EL sensors represent the state of the art for water cycle and process applications. They feature an extremely wide measurement range of more than 1:1000 without linearization software. This allows for very accurate measurements over a wide flow rate range, including lower flow rates previously too small to measure. The sensors operate using the Faraday principle where a conductor in a magnetic field generates a voltage perpendicular to the field.

    Original Description:

    S103C E_magnetici Flowmter CH2200_2500 Flanged Pipe

    Original Title

    S103C E_magnetici Flowmter CH2200_2500 Flanged Pipe

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The CH 2200 EL and CH 2500 EL sensors represent the state of the art for water cycle and process applications. They feature an extremely wide measurement range of more than 1:1000 without linearization software. This allows for very accurate measurements over a wide flow rate range, including lower flow rates previously too small to measure. The sensors operate using the Faraday principle where a conductor in a magnetic field generates a voltage perpendicular to the field.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    455 views7 pages

    S103C E - Magnetici Flowmter CH2200 - 2500 Flanged Pipe

    Uploaded by

    Adam Samy
    The CH 2200 EL and CH 2500 EL sensors represent the state of the art for water cycle and process applications. They feature an extremely wide measurement range of more than 1:1000 without linearization software. This allows for very accurate measurements over a wide flow rate range, including lower flow rates previously too small to measure. The sensors operate using the Faraday principle where a conductor in a magnetic field generates a voltage perpendicular to the field.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 7

    SENSORS CH 2200/2500EL

    CH 2200 EL / CH 2500 EL sensors represent the state of the art of


    CHEMITEC production for water cycle and process applications.
    The new structure for the generation of the magnetic field, the
    innovative route of the signal generated by the electrodes, provide a
    sensor with an extremely wide measurement range:
    EL= Extended Linearity.
    This new sensors series introducing a measurement range of
    more than 1:1000 without linearization software.
    These kinds of performances allow very accurate measures on a
    wide flow rate range and to count lower flow rates that, before, would
    have been reset because of the effect of the converters cut off.
    This flanged sensors series bases its operation on the Faraday
    Principle, by which a conductor crossing a magnetic field
    generates a potential perpendicularly orientated to the same field.
    In this case the flow tube made in stainless steel AISI 304 is
    equipped with carbon or stainless steel flanges,
    two coils are installed on the top and inferior part; the magnetic field,
    generated by the electric current crossing the coil, induces in the
    electrodes a difference in the potential proportional to the
    flow rate.
    With the aim of measuring such potential of very low values, the
    interior of the flow tube is electrically insulated, thus the process liquid is no longer in contact neither with the material of
    the flow tube nor with that of the flange. The converter used generates the current supplying the coil, acquires the
    electrodes difference of potential, process the signal to calculate the flowrate and administers the communication with
    the exterior. The entire sensor, when installed in the separate version, has a degree of protection IP 68 suitable for a
    permanent immersion in water up to a depth of 1.5m thanks to a welded plate structure containing the coil and the
    electrodes.
    BODY AND FLANGE
    The flange and the sensor external surface are acrylic painted. This treatment gives the sensor an excellent resistance to
    water, even in permanent immersion. When special ambient conditions require it, the CH 2000 EL / CH 2500 EL may be
    supplied in stainless steel, flange included (see Table 2).

    INTERNAL LINING
    The standard internal insulating lining is in PTFE for diameters from ND 15 to ND 200, in hard rubber (ebonite for food)
    for diameters of more than ND 200. On request, the sensors may be supplied coated with PTFE with diameters of more
    than ND 200. The temperature of the liquid to be measured is limited by the kind of internal lining used. (see Table 4).
    ELECTRODES
    The standard electrodes are in Hastelloy C and, therefore, guarantee a wide compatibility with the process liquids, if
    required, they may be supplied in the materials shown in Table 3.

    COUPLING AND CONNECTING TO SENSORS


    CH 2200 EL / CH 2500 EL sensors may be coupled with any CHEMITEC converters. In the separate version thesensor
    is connected to the converter by means of a cable whose length depends on the liquid conductivity; the maximum length
    not exceeding 100 metres as shown in Figure 1. If these sensors are inserted in a plastic or lined pipe line, they require
    the use of two grounding rings of the liquid, which are inserted between the flange and the counter flange or the
    installation of the grounding electrode. An empty pipe device is also installed .
    CHOICE OF DIAMETRER
    When choosing the diameter we advice keeping at the full scale flow rate, a liquid velocity of at least 23 m/s. The
    maximum acceptable velocity is of 10 m/s. Figure 3 provides the flow rate for each ND (nominal diameter) according to
    the liquid velocity.

    Chemitec S.r.l. Via I.Newton, 30 50018 Scandicci (FI)- ITALY


    tel +39 0557576801 fax +39 055756697
    E-mail: sales@chemitec.it Web Site: www.chemitec.it

    MAXIMUM TEMPERATURE OF THE LIQUID


    In the separate version the maximum liquid temperature allowed is shown in Table 4. In the compact version instead, the
    maximum temperature allowed depends on the ambient temperature. This is due to the required cooling of the
    electronics. The maximum liquid temperature allowed for the compact version should be 80C.
    CALIBRATION AND MAXIMUM ERROR
    CH2200 EL / CH2500 EL sensors belong to the reference Group B1 (ISO 11631). Each sensor is calibrated by a
    hydraulic bench equipped with a reference weighting system and ACCREDIA certified. The uncertainty of the measure
    is equal to 0.2% of the read flowrate value when the velocity of the liquid is more than 0.2 m/s. The repeatability of the
    measure is in the order of 0.1%
    REFERENCE STANDARDS
    The CHEMITEC magnetic meters are marked CE and are
    manufactured according to the following standards:
    * CEI EN 61010-1 * EN 50081 - 1
    * UNI EN ISO 6817 * EN 50082 - 1
    * 2006/95/CE, 93/68 (LVD) * EN 1434
    * 2004/98/CE, 92/31 (EMC)
    On request, CH2200 EL and CH2500 EL sensors can be provided
    with certification ATEX II 2 GD EEx mb IIC T4 U.

    Chemitec S.r.l. Via I.Newton, 30 50018 Scandicci (FI)- ITALY


    tel +39 0557576801 fax +39 055756697
    E-mail: sales@chemitec.it Web Site: www.chemitec.it

    GENERAL CHARACTERISTICS OF SENSOR CH2200 EL / CH 2500 EL

    Chemitec S.r.l. Via I.Newton, 30 50018 Scandicci (FI)- ITALY


    tel +39 0557576801 fax +39 055756697
    E-mail: sales@chemitec.it Web Site: www.chemitec.it

    CH 2200 EL Separate PN10

    CH 2200 EL Separate PN16

    CH 2500 EL Separate PN10

    CH 2500 EL Separate PN16

    Chemitec S.r.l. Via I.Newton, 30 50018 Scandicci (FI)- ITALY


    tel +39 0557576801 fax +39 055756697
    E-mail: sales@chemitec.it Web Site: www.chemitec.it

    CH 2200 EL Separate PN25

    CH 2200 EL Separate PN40

    CH 2500 EL Separate PN25

    CH 2500 EL Separate PN 40

    Chemitec S.r.l. Via I.Newton, 30 50018 Scandicci (FI)- ITALY


    tel +39 0557576801 fax +39 055756697
    E-mail: sales@chemitec.it Web Site: www.chemitec.it

    CH 2200 EL Separate ANSI 150

    CH 2200 EL Separate ANSI 300

    CH 2500 Separate ANSI 150

    CH 2500 EL Separate ANSI 300

    Chemitec S.r.l. Via I.Newton, 30 50018 Scandicci (FI)- ITALY


    tel +39 0557576801 fax +39 055756697
    E-mail: sales@chemitec.it Web Site: www.chemitec.it

    Flowrate Table (Blue values are preferable)

    Chemitec S.r.l. Via I.Newton, 30 50018 Scandicci (FI)- ITALY


    tel +39 0557576801 fax +39 055756697
    E-mail: sales@chemitec.it Web Site: www.chemitec.it

    You might also like