MT - Gen
MT - Gen
Question : GENERAL
FINAL EXAMINATION
-----------------------------------------------------------------------------------------------------------1.0
2.0
3.0
Iron
Nickel
Cobalt
All of the above
5.0
4.0
Strong indication
Fuzzy indication
No indication
Weak indication
What is the maximum current required to magnetize the part 10 long and
2 dia by solenoid coil method having 5 turns?
a)
b)
c)
d)
1400Amps
1000Amps
2000Amps
700Amps
Page 1 of 7
6.0
The field produced in a hollow magnetic cylinder pipe of dia 80mm with a
central conductor of copper material will be
a)
b)
c)
d)
7.0
8.0
10.0
True
False
Partially can be done
None of the above
11.0
By longitudinal magnetization
By circular magnetization
By vector magnetization
By polarized magnetization
After carrying out magnetic particle testing on the part which requires heat
treatment for inducing better material properties, the examined part shall
be demagnetized
a)
b)
c)
d)
9.0
AC + wet
DC+ dry
DC + wet
HWDC+ dry
700Amps
540Amps
1200Amps
110Amps
Page 2 of 7
12.0
For effective coil magnetization, the L/D ratio of the specimen inside the
coil shall be
a)
b)
c)
d)
13.0
Greater than 2
Less than 1
Equal to 2
None of the above
The purpose of filter for mercury arc vapour lamp in carrying out
Fluorescent magnetic particle test
a) Supplying light of correct wavelength to cause fluorescence on
material
b) To pass all the wavelength of light falling on the specimen
c) To increase the intensity of light falling on the specimen
d) None of the above
14.0
15.0
16.0
Flux meter
Field indicator
Lacto meter
Hydrometer
17.0
Discontinuity
Defect
An indication
Magnetic writting
Drop test
Visual examination under black light
Settling test
Visibility test
Page 3 of 7
18.0
19.0
Which is the best for detecting the discontinuity with high sensitivity in
Ferro magnetic materials
a)
b)
c)
d)
20.0
23.0
22.0
Residual method
Continuous method
Vibration method
None of the above
The most convenient and widely used method of preserving the indication
is
a)
b)
c)
d)
21.0
Amperes
Amperes turns
Lifting power by using known standard weight
Not necessary to check the field adequacy
Page 4 of 7
24.0
25.0
The system performance of horizontal units by dry and wet methods using
a ring with holes at various depth and a conductor at the centre, is
adapted by what type of method and magnetization
a)
b)
c)
d)
26.0
Shrinkage
Hot tear
Porosity
Cold shut
The name of the sub surface defect that will occur in the manufacture of
piping and tubing is
a)
b)
c)
d)
29.0
Lack of fusion
Change of thickness
Drilled hole near the surface
Both b& c
The type of defect that will occur in casting solidification caused by non
uniform cooling as well as change of thickness resulting in rupture of the
surface of the metal
a)
b)
c)
d)
28.0
27.0
Field indicator
Pie gauge
Artificial flaw shim
All of the above
cold shut
Stringer
Lack of fusion
Piping
One of the false indication that will occur during the MT of butt welds of
plates and pipes by prod method is
a)
b)
c)
d)
Lack of penetration
Excess penetration
Magnetic writing
Blow hole
Page 5 of 7
30.0
If one inch and two inch dia of bars are magnetized by passing the same
current individually through them, the magnetic field will be
a)
b)
c)
d)
31.0
A one inch thick butt welded mild steel was welded using metal arc
process. On testing with prod method with dry powder star shaped
indication appearing in the middle of the weld width is most likely due to
a)
b)
c)
d)
32.0
Batteries
Rectified AC
Generators
All of the above
35.0
34.0
Crater cracks
Micro cracks
Transverse crack
Heat treatment cracks
33.0
Forging laps
Surface cracks
Seams in pipes
Deep seated cavities
Page 6 of 7
36.0
During the testing of Magnetic particle testing for finding sub surface
discontinuities. 6mm length crack appeared an austenitic stainless steel
weld of thick 25mm
a)
b)
c)
d)
37.0
True
False
More information required
% of chromium shall be increased
38.0
Which one of the following elements is not among the those strongly
attracted by magnetism?
a)
b)
c)
d)
39.0
40.0
A weld was inspected after the rework. Some odd hazy indications were
seen in cluster at various locations along the weld in the parent material
that seemed to have no connection with the weld. What could be the
significance of these indications
a)
b)
c)
d)
Non relevant residual field left by the original test that had used prod
Magnetic writing with no significance
Cracks in the parent metal
Arc tracks with no significance
Page 7 of 7
Page 8 of 7