Chapter 1

Chapter-1
1.1 Introduction:
A most important & significant look in our modern civilization is energy of different
forms. Many necessary functions can be at a stand still with out energy. So energy is a
part of our life. There are various form of energy consumption process such raw
energy in falling water, in deposits of coal, oil and gas etc are most well known form.
Energy sources which are regenerated after a regular time cycle are commonly known
as renewable sources of energy like hydro power, solar energy, wind energy, tidal
energy, biomass fuels etc. In a particular location available renewable energy sources
are finite quantity, which depends on their respective characteristics feature. When
renewable energy sources is extracted at a higher rate then its regenerative rate is
becomes non renewable. Energy produced from renewable natural resources &
technologies.
The present energy demand is increasing day by day in Bangladesh due to various
reasons such as increasing population, the aspiration for improved living standard and
general economic and industrial growth. The power generation system is principally
depended on imported petroleum oil and own natural gas. On the other hand, as the
information about the deposits of fossil fuels in Bangladesh, if they are consumed at
the present rate, the reversed natural gas and coal will be exhausted by the year 2020 to
2030. To reduce the dependency on imported fuel and the pressure on natural gas, the
present power generation system must be diversified and at the same time indigenous
energy resources have to be explored and developed. It may be mentioned that concern
for environment is a now a universal issue and conventional energy gives rise to
greenhouse gases with adverse consequences for health and climate. In these
perspectives, harnessing of renewable energies and development of relative
technologies is a highly important strategic option. Communities in rural areas and
mainly in remote areas of Bangladesh have very little possibilities to participate on the
national electricity supply. Therefore, and in the context of environment protection,
renewable energies can contribute substantial to the delivery of alternative energy to
the users etc. are some of the key issues that determine the need for technological
inventions in solving energy problems in the rural areas.
1.2 Definition of Energy:

Energy:
Energy is the measure of a physical system. It defines the quality of the changes and
processes, which take place in the Universe, beginning with movement and finishing
with thinking.
1.3 Renewable Energy

Renewable energy is energy generated from natural resourcessuch as sunlight, wind,
rain, tides, and geothermal heatwhich are renewable (naturally replenished). In
2006, about 18% of global final energy consumption came from renewable, with 13%
coming from traditional biomass, such as wood-burning. Hydroelectricity was the next
largest renewable source, providing 3% of global energy consumption and 15% of
global electricity generation. Wind power is growing at the rate of 30 percent annually,
with a worldwide installed capacity of 121,000 megawatts (MW) in 2008, and is
widely used in European countries and the United States. The annual manufacturing
output of the photovoltaic industry reached 6,900 MW in 2008, and photovoltaic (PV)
power stations are popular in Germany and Spain. Solar thermal power stations
operate in the USA and Spain, and the largest of these is the 354 MW SEGS power
plant in the Mojave Desert. The world's largest geothermal power installation is The
Geysers in California, with a rated capacity of 750 MW. Brazil has one of the largest
renewable energy programs in the world, involving production of ethanol fuel from
sugar cane, and ethanol now provides 18 percent of the country's automotive fuel.
Ethanol fuel is also widely available in the USA. While most renewable energy
projects and production is large-scale, renewable technologies are also suited to small
off-grid applications, sometimes in rural and remote areas, where energy is often
crucial in human development. Kenya has the world's highest household solar
ownership rate with roughly 30,000 small (20100 watt) solar power systems sold per
year. Some renewable-energy technologies are criticized for being intermittent or
unsightly, yet the renewable-energy market continues to grow. Climate-change
concerns, coupled with high oil prices, peak oil, and increasing government support,
are driving increasing renewable-energy legislation, incentives and commercialization.
New government spending, regulation and policies should help the industry weather
the 2009 economic crisis better than many other sectors.
Main forms/sources of renewable energy
Fig: 1.1
1.4 Types of Renewable Energy:

Biomass
Geothermal Energy
Wind Energy
Photovoltaic (PV) Cells
Hydropower
Hydropower:
Hydropower is the largest source of renewable energy. This renewable source of
energy provides 10% of the nations electricity. As of now, there are 77,000
Megawatts of hydropower, enough to provide 35 million homes with energy.
Converting flowing water into usable energy produces hydropower. Most of this water
comes from rivers and is released through turbines to produce energy. Although this
power source does not release pollution, it can possibly harm fish and wildlife,
displace people, and alter the quality of water. Better technology is trying to reduce
the loss of aquatic life, but the problem with this technology is that it is highly
expensive and takes a long time to build.
Biomass/Bioenergy:
Biomass makes up about 7,000 Megawatts of renewable electricity. Biomass fuels
stem from industrial processing, such as forestry and wood products, agriculture and
wood products, and construction and transportation. Biomass can replace coal in
power plants because it produces less sulfur dioxide than coal. Mill operations seem to
be the main source of biomass energy in the U.S. Europe, on the other hand, draws its
main source of bioenergy from urban wood waste. Third world countries make timber
their main source of bioenergy. According from statistics from the International
Energy Agency, 11% of the world derives its energy from biomass. Developing
countries use about 35%, while the poorest ones use roughly 90%. One way to convert
biomass into usable energy is through gasificationconverting biomass to gas and
burning it in a gas turbine.
Wind Energy:
Wind energy produces about 2,500 Megawatts of energy, and generates a mere .1% of
our electricity. The wind rotates blades around a hub, which is connected to the main
shaft. The main shaft spins a generator. The size of turbines is determined by how
much energy is needed. Small wind turbines are usually used for homes, farms and
ranches. Other ways to use wind energy include grinding grain and pumping water.
Wind is classed in categories of 1 through 7, with 7 being the highest and 1 being the
lowest. A good wind source that has a class of 3 or higher is the east coast and along
the Appalachian Mountains. North Dakota is an excellent wind source.
The disadvantages of wind energy are that again, the technology is very expensive, the
machinery is known to be noisy, birds have been killed by running into the turbines,
and the wind might not be present at certain times throughout the year.
Photovoltaic (PV) Cells:

Solar Module:
PV cells produce electricity from sunlight. Materials used in computer chips are
similar to materials used in PV cells. These materials absorb sunlight, which frees the
electrons from their atoms and allows them to generate electricity. PV cells are great
because they dont require high maintenance, are very reliable, and dont produce
pollutants.
Geothermal Energy:
Geothermal energy is capable of producing about 2,800 Megawatts of energy per year,
0r roughly .2% of the energy in the U.S. Geothermal energy is produced from naturally
occurring steam and hot water from under the Earths surface. The steam rotates a
turbine, which in turn powers an electric generator. Also, hot water can be used to
directly heat building. The downside to geothermal energy is that land sites is very
hard to find and extremely rare. A positive fact is that geothermal energy is very cost
effective and reliable.
1.5 Advantages of Renewable Energy:

With the goal of reducing air pollution and advancing public health, renewable energy
methods like solar and wind are being embraced around the world. Renewable energy
has several environmental and economic benefits.
Environmental Benefits:
Because renewable energy sources like solar and wind do not require the use of fossil
fuels, they do not emit carbon dioxide. Carbon dioxide is a bi-product of burning coal
and gas. By reducing the amount of fossil fuels we burn, we are decreasing the amount
of pollutants and chemicals being emitted into the atmosphere.
Wind Energy:
Electricity generated by wind through turbines is a fast-growing renewable energy
source around the world. These turbines can be placed on land or offshore. One turbine
can create enough energy to power 500 homes that use average levels of electricity.
Solar:
Solar energy is generated through the sun's heat. To put into context the immense
power of the sun, the entire supply of coal, oil and natural gas is equivalent to the
power put off by the sun in just 20 days. This energy can be harnessed through the use
of photovoltaic solar panel that can be put on roofs, atop building and even on cars.
Public Health:
Pollution coming from power plants taints our air supply and causes asthma. Through
the use of renewable energy, we could eliminate these harmful substances in the air,
leading to a healthier population.
Cost and Supply:
Once the solar panels are installed and the windmills are put up, renewable energy is
essentially free. It costs nothing to use the suns rays, and taking advantage of a windy
day is free. Furthermore, the supply of wind is not going to diminish. The sun's rays
are also prevalent and will exist for millions of years.
Chapter 2
Renewable Energy in Bangladesh
2.1 Renewable Energy Technologies Suitable for Bangladesh:
Different types of renewable energy technologies (RET) applications suitable for
Bangladesh are described in the subsequent headings.
Solar Thermal
Solar photovoltaic (SPV)
Biomass
Small Hydro
Waste Energy
2.2 Present Scenario of Conventional and renewable energy

(Electric power) Utilization in Bangladesh
Total insulated power in grid

electricity is 5254 MW
Hydro
230 MW
Furnace Foil
280 MW
Coal
250MW
Diesel
200MW
Gas
4285MW
Total insulated power off grid electricity

is 22.55 MW
2.3 Significant Progress of
Micro Hydro
0.1MW
Biomass/Biogas
0.5MW
Wind
2.5MW
Solar
18.55MW
Renewable Energy Technology in

Bangladesh:
Total installed Power for off grid electricity is 20MW from RE
Technology
Capacity
Solar PV stand
alone system with
ownership model
365,000 SHS and

its integrated
capacity is 18.5
MW
6000 SHS
Solar PV stand
alone system (fee
for services)
Centralized PV
300 KW
system
Micro Hydro
10KW
Biomass/biogas
400 KW
Wind
2.5 MW
Improved Cooking 80,000 nos
Stove
Source: www.reein.org
Implementing
Agency
14 partner
organizations of
IDCOL like RSF,
GS, BRAC etc.
REB
Financial partner
LGED , BPDB
IDCOL (World
Bank, GEF, GTZ
and KFW, ADB,
IDB)
World Bank, GEF,
GTZ and French
grant
UNDP, GOB
LGED
Private/Public
BPDB
Pos of GTZ
UNDP
IDCOL, GTZ
UNDP, WB
GTZ
2.4 Government Support in Renewable Energy Sector in

Bangladesh:
Sector
Opportunity
Government policy
Government setup a target that at least 5% electricity by

2015 and 10% by 2020 will be generated from RE
Duty & VAT
Government wipe out all sort of duty from renewable

energy commodities
Tax Holiday (according to According to declared RE policy, Renewable energy

RE policy)
company will enjoy 5 years tax holiday from its inception
however current budget doesn't support it
Manufacturing plant for

PV module
Duty of capital machinery for assembling of PV module is

exempted.
2.5 Ongoing Renewable Energy Technology (RET)

Projects in Bangladesh:
Renewable energy development project- REB/IDCON.
Sustainable rural energy- LGED
Solar & Wind resource assessment project- RERC, DU
SHS project- Grameen Sakti.
PREGA- REB/BPDB
GTZ funded project REB.
Biogas pilot project LGED.
RET in Asia- CMES/KUET
SHS project- BRAC.
CHT SHS project- BPDB.
RET feasibility study- BCSIR.
SHS project-TMSS.
Solar home lighting system- Centre for mass education in science (CMES)
Solar home system- Integrated Development Foundation (IDF)
Wind power generation- BPDB
Hybrid system- Grameen Sakti, BRAC.
Wind mill water pumping-LGED.
Micro hydro power plant- LGED.
Biogas plants- BCSIR, BRAC.
Chapter 3
Energy and Sun
3.1 Definition of Energy:

Energy is the measure of a physical system. It defines the quality of the changes and
processes, which take place in the Universe, beginning with movement and finishing
with thinking. The unity and the connection between the movement forms of
substance, their lively capacity of mutual transformation, allowed the measuring of
different forms of substance through a common aspect: energy.
3.2 Types of Energy:

The name of energy forms is related to:
1. The way energy is perceived (for example: mechanical energy, electrical energy,
energy of light)
2. What carries the energy (for example: thermal energy)
3. The origins of energy (for example: nuclear energy, hydraulic energy, wind energy,
geothermal energy, and solar energy).
3.3 Sun:
The Sun
Figure 1. The Su
Figure 1: The source of all energy
3.4 Surface temperature:

We know that the sun is a sphere of diameter 1,400,000 km, that its outer regions are
hot gases, mostly hydrogen and helium, and that its surface temperature is about 6,000
degrees Celsius (about 11,000 degrees Fahrenheit). Any surface at that temperature
will generate heat and light. The burners of an electric stove or a toaster oven, for
example, are not at 6,000 C., but when they're turned on they are "red hot"; they emit
heat and light and the light is red. If we could raise the temperature to 6,000 C. they
would become "white hot", and emit light very much like the sun's. Similarly, a fire is
a region of gases at a temperature high enough to generate heat and light.
So the question becomes not so much why is there heat and light, but where does the
energy come from to keep the surface temperature of the sun at 6,000 degrees?
3.5 Conversion of sunlight into electricity:

Light knocks loose electrons from silicon atoms. Free electrons have extra energy.
Internal electric field (junction) pushes electrons to front of cell. Electric current flows
on to other cells or to the load. Cells never run out of electrons.
Sun -Earth relation-1
Sun-Earth relation-2
3.6 Extraterrestrial radiation:

It is also important to know the spectral distribution of extraterrestrial radiation, i.e. the
radiation that would be received in the absence of atmosphere. The extraterrestrial
solar spectrum at mean earth sun distance can be divided into following three main
regions, usually divided into wave bands (1 micron = 1m = 10-6, mm = 10-6 meter).
.Ultraviolet region (l < 0.38 mm). Percentage of solar radiation 7%.
.Visible region (0.38 < l < 0.78 mm) Percentage radiation 47.3%.
.Infrared region (l > 0.78mm) percentage ration 45.7%
Figure: Extraterrestrial radiation
Extraterrestrial radiation at any time of the year is given by
Ion = Isc 1
0.033 cos
360 n
365
where Isc is the solar constant and Ion is the extraterrestrial radiation measured on a
plane normal to the radiation on the n day of the year counted from January 1st as
n=1.
Solar Constant is defined as the energy from the sun received on a unit area of the
surface perpendicular to radiation at mean earth sun distance. WRC adopted a value of
1367W/m2
3.7 Equation of time:

E=
229.2(0.000075+0.001868 B- 0.032077 sin B - 0.014615 cos 2B-
0.04089sin2B)
Where, B = (n-1)360/365 and n is the day of the year.
Monthly averaged daily global radiation (kWh/m2/day)
Jan
Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Average
4.02
4.64 5.01 5.37 4.83 4.22 4.00 4.13 4.15 4.23 4.04 3.80 4.37
3.8 Solar Energy Spectrum:
Figure 2: Spectrum of Solar Radiation
FIGURE 3. Definition of the angles for the description of the position of the sun
Figure 4: Angles to define the position of the sun and the orientation of a tilted
plane
Chapter 4
Aspects of Solar Energy in Bangladesh
4.1 Solar energy uses:
Solar energy uses in various respects. Such as;
Generate electricity using photovoltaic solar cells.

Generate electricity using concentrated solar power.
Generate electricity by heating trapped air, which rotates turbines in a solar
updraft tower.
Heat buildings, directly, through passive solar building design.
Heat foodstuffs, through solar ovens.
Heat water or air for domestic hot water and space heating needs using solarthermal panels.
Heat and cool air through use of solar chimneys.
Generate electricity in geosynchronous orbit using solar power satellite.
Solar air conditioning.
4.2 Solar Photovoltaic:

4.2.1 Photovoltaic:
Becquerel first discovered that sunlight could be converted directly into electricity in
1839, when he observed the photogalvanic effect. But the first solar cell, developed by
Chapin, Fuller and Pearson, revealed in 1954. It had an efficiency of 6% only. In 1956,
the invention of 10% efficient silicon solar cell was reported. Only two years later, the
first solar cells were used on the Vanguard I orbiting satellite. Since then, the use of
solar electricity (also known as photovoltaics) is going on increasing year by year and
some have been in continuous outdoor operation on Earth or in space for over 30
years.
4.2.2 Advantages of Photovoltaic:

Photovoltaic has shown, since the 1970s, that the human race can get a substantial
portion of its electrical power without burning fossil fuels (coal, oil or natural gas) or
creating nuclear fission reactions. Photovoltaic helps us avoid most of the threats
associated with our present techniques of electricity production and also has many
other benefits. Photovoltaic has shown that it can generate electricity for the human
race for a wide range of applications, scales, climates, and geographic locations. It can
provide electricity to remote transmitter stations in the mountains allowing better
communication without building a road to deliver diesel fuel for its generator. It can
supply electricity to the community in an island, which is very far from utility grid, or
can supply electricity to the people of poor countries like African countries, where
people are scattered and grid electricity is not feasible.
Fossil-fuel plants have many disadvantages: a wide range of environmentally
hazardous emissions, parts which wear out, steadily increasing fuel costs, they are not
modular (deployable in small increments), and they suffer low public opinion (no one
wants a coal burning power plant in their neighborhood). Photovoltaic suffers none of
these problems. Some other advantages of photovoltaic are given below-
Fuel source of photovoltaic is vast and essentially infinite.

No emissions, no combustion or radioactive fuel for disposal.
Low operating cost.

No moving parts.
No high temperature corrosion or safety issue.
High reliability in modules (>20 years).
Completely modular (small or large increment is possible).
Quick installation.
Can be integrated into new or existing building structures.
Can be installed at nearly any point-of-use.
Daily output peak may match local demand.
High public acceptance.
Excellent safety record.
4.3 Solar Heating:
Figure: The family living in this house enjoys hot water heated
by the sun with a solar thermal system
Solar heating harnesses the power of the sun to provide solar thermal energy for solar
hot water, solar space heating, and solar pool heaters. A solar heating system saves
energy, reduces utility costs, and produces clean energy. The efficiency and reliability
of solar heating systems have increased dramatically, making them attractive options
in the home or business. But there is still room for improvement.
4.3.1 Solar Heating Basics:

Solar heat can be used for solar water heating, solar space heating in buildings, and
solar pool heaters. Solar water heaters and solar space heaters are constructed of solar
collectors, and all systems have some kind of storage, except solar pool heaters and
some industrial systems that use energy "immediately."
Figure: These solar collectors are part of

the solar domestic hot water system.
The systems collect the sun's energy to heat air or a fluid. The air or fluid then
transfers solar heat directly to a building, water, or pool.
4.3.2 Solar Heating in Use:
Figure: This evacuated-tube solar water heating collector is on the roof of the
Rhode Island School of Design's Solar Decathlon competition house.
Since the early 1970s, the efficiency and reliability of solar heating systems and
collectors have increased greatly, and costs have dropped. Today's solar thermal
systems are used for solar water heating, solar pool heating, and in solar space heating.
4.4 Solar Thermal Electricity:

Solar energy can also be used to make electricity. Some solar power plants, like the
one in the picture to the right in California's Mojave Desert, use a highly curved mirror
called a parabolic trough to focus the sunlight on a pipe running down a central point
above the curve of the mirror. The mirror focuses the sunlight to strike the pipe, and it
gets so hot that it can boil water into steam. That steam can then be used to turn a
turbine to make electricity.
Figure 2.5: Curved mirror to produce electricity

In California's Mojave Desert, there are huge rows of solar mirrors arranged in what's
called "solar thermal power plants" that use this idea to make electricity for more than
350,000 homes. The problem with solar energy is that it works only when the sun is
shining. So, on cloudy days and at night, the power plants can't create energy. Some
solar plants are a "hybrid" technology. During the daytime they use the sun. At night
and on cloudy days they burn natural gas to boil the water so they can continue to
make electricity.
4.5 Solar Cooking:

Solar cookers use sunlight for cooking, drying and pasteurization. Solar cooking
offsets fuel costs, reduces demand for fuel or firewood, and improves air quality by
reducing or removing a source of smoke.
Concentrating solar cookers use reflectors to concentrate light on a cooking container.
The most common reflector geometries are flat plate, disc and parabolic trough type.
These designs cook faster and at higher temperatures (up to 350 C) but require direct
light to function properly.
Figure 2.6: Solar cooking dish
4.6 Solar Water Heater:

Where heat from the Sun is used to heat water in glass panels in our roof. This means
we don't need to use so much gas or electricity to heat our water at home. Water is
pumped through pipes in the panel. The pipes are painted black, so they get hot when
the Sun shines on them. Many homes used solar water heaters.
Figure 2.4: Solar water heating mechanism

Today, solar water heaters are making a comeback. They heat water for use inside
homes and businesses. They also heat swimming pools like in the picture. Panels on
the roof of a building, like this one on the right, contain water pipes. When the sun hits
the panels and the pipes, the sunlight warms them.
4.7 Solar dryer:

Agricultural and other products have been dried by the sun and wind in the open air for
thousands of years. The purpose is either to preserve them for later use, as is the case
with food; or as an integral part of the production process, as with timber, tobacco and
laundering. In industrialized regions and sectors, open air-drying has now been largely
replaced by mechanized dryers, with boilers to heat incoming air, and fans to force it
through at a high rate. Mechanized drying is faster than open-air drying, uses much
less land and usually gives a better quality product. But the equipment is expensive
and requires substantial quantities of fuel or electricity to operate.
4.7.1 Solar dryer Application:

For centuries people of various nations have been preserving dates, figs, apricots,
grapes, bananas, pineapples, other fruits, herbs, cassava, yams, potatoes, corn, peas,
onions, garlic, carrots, peppers, milk, coffee, meat, and fish by drying.
But drying is also beneficial for hay, copra (kernel of the coconut), tea and other income
producing non-food crops. It is worth noting that until around the end of the 18th century when
canning was developed, drying was virtually the only method of food preservation.
4.7.2 Solar Drying Can Improve Agricultural Products:

Dehydration of vegetables and other food crops by traditional methods of open-air sun drying
is not satisfactory, because the products deteriorate rapidly. Furthermore, traditional methods
do not protect the products from contamination by dirt, debris, insects, or germs. A study by
Akwasi Ayensu from the Dept. of Physics at the University of Cape Coast, Cape Coast, Ghana
demonstrates that food items dried in a solar dryer were superior to those which were sun dried
when evaluated in terms of taste, color, and mould counts. He asserts, and many others agree
that solar drying systems must be developed to utilize this energy resource to improve food
preservation.
This translates into quality products that can be stored for extended periods, easily transported
at less cost while still providing excellent nutritive value.
Chapter 5
Solar PV Equipment
5.1 Solar cells:
Photovoltaic (PV) or solar cells are PN junction Semiconductor devices. It converts
sun light into direct current electricity. Groups of solar cells are electrically connected
into PV modules, arrays. PV modules or arrays can be used to charge batteries .This
system can be used to power any number of Electrical loads. PV systems can produce
alternating currents or Inverter. Compatible with any conventional appliances and
operate in parallel with and interconnected to the Utility grid.
Solar cells often are distinguished by their type of semiconductor junction(A) Homojunction (n + p layer is of the same material)
(B) Heterojunction (n + p layer is of different material)
(c) Schottky junction (semiconductor / metal)
(d) MIS (Metal / Isolator / Semiconductor

(e) SIS (Semiconductor / Isolator / Semiconductor)
5.1.1 Connect cell to make modules:

One silicon solar cell produces 0.5V to 0.6V
Usually 36 cells are connected together to make a Module
Such one module has enough voltage to charge 12 volt batteries and Run
pumps and motors
PV Module is basic building block of a PV power system
Modules can be connected to produce more power
Figure: Cells, Modules, Panels and Arrays
5.1.2 Types of Solar Cells:

Solar cells can be classified according to semiconductor materials of the cell,
according to the crystalline structure of the material, and according to the number of
junctions of the cell. According to the crystalline structure of the material there are
three types of solar cells.
1. Single-crystalline or monocrystalline cells
2. Multi-crystalline or polycrystalline cells and
3. Amorphous cells
Amorphous solar
cell
Polycrystalline
solar cell
Single Crystal
solar cell
5.1.2.1. Monocrystalline Cells

Monocrystalline cells are the most important type, because they have the highest
conversion efficiency (25%), and the base material, which is extremely pure silicon, is
already well established in the field of semiconductor production. Currently, the
methods of producing silicon single-crystals are primarily either the Czochralsky
process or the floating zone technique. In the Czochralsky process, monocrystalline
silicon grows on a seed, which is pulled slowly out of the silicon melt. With both
methods, silicon rods are produced, which are cut into slices of 0.2 to 0.4 mm
thickness. The discs (wafers) produced in this way, then, undergo several further
production steps. These are, for instance:
a. Grinding and cleaning
b. Doping
c. Metallization
d. Antireflection coating
Figure: Monocrystalline Cells
5.1.2.2 Polycrystalline Cells:

The manufacturing process for monocrystalline silicon is highly energy-intensive and
therefore very expensive. For this reason, in many cases polycrystalline silicon (PolySi) is preferred. Poly-Si develops, when a silicon melt is cooled down slowly and
controlled. The yielded silicon ingot is sliced and further processed, as described
before. The pulling of the single-crystal can be omitted this way. Inside the Poly-Si
crystal, there are crystalline regions, which are separated by grain boundaries. The
losses occurring at these grain boundaries cause the lower efficiency (less than 20%)
of polycrystalline cells compared with monocrystalline ones. Despite this
disadvantage, the importance of polycrystalline cells is growing, because of the lower
production costs.
Figure: Polycrystalline Cells
5.1.2.3 Amorphous Cells:

In order to avoid the energy-intensive production process mentioned above, and to
avoid the cutting loss of the slicing process, a vapor-phase technique has been
developed in which a thin film of silicon is deposited from a reactive gas such as silane
(SiH4) on a carrier material like glass and doped in a further step. The semi conducting
material grown in this way is called amorphous silicon.
This technology has two disadvantages: first, the conversion efficiency is considerably
low, i.e., less than 10%; second, the cells are affected by a degradation process during
the initial months of operation, which reduces the efficiency furthermore.
These disadvantages are compensated by the Relatively simple and inexpensive manufacturing process
The possibility of producing cells with a larger area
The lower energy consumption and
Easy to use in small electronic equipment.
Figure: Amorphous Cells
5.2 Charge Controller:

Charge controller is an electronic device which is used in solar system. A solar charge
controller is needed in virtually all solar power systems that utilize batteries.
The job of the solar charge controller is to regulate the power going from the solar
panels to the batteries. Overcharging batteries will at the least significantly reduce
battery life and at worst damage the batteries to the point that they are unusable.
The most basic charge controller simply monitors the battery voltage and opens the
circuit, stopping the charging, when the battery voltage rises to a certain level. Older
charge controllers used a mechanical relay to open or close the circuit, stopping or
starting power going to the batteries.
Modern charge controllers use pulse width modulation (PWM) to slowly lower the
amount of power applied to the batteries as the batteries get closer and closer to fully
charged. This type of controller allows the batteries to be more fully charged with less
stress on the battery, extending battery life. It can also keep batteries in a fully
charged state (called float) indefinitely. PWM is more complex, but doesnt have
any mechanical connections to break.
The electricity produced in the solar panel is stored in the battery. The electricity
stored in the battery is used at night. This whole process is monitored by the charge
controller.
A typical charge controller (Phocos) is shown in the figure bellow-
Figure: Charge controller
5.2.1 Function of charge controller:

The main function of a charge controller or regulator is to fully charge a battery without
permitting overcharge while preventing reverse current flow at night. Other functions are-
Stop the process of the battery when it is fully charged.

Disconnect the load during low voltage.
Disconnect the load during high voltage.
Monitor the battery voltage, state of charge, SOC etc.
To give alarm during fault condition.
Current measurement.
Detect when no energy is coming from the solar panels and open the circuit,
disconnecting the solar panels from the batteries and stopping reverse current
flow.
Charge controller is used for co-ordination and control among the battery, load and
solar panel. Charge controller stores the electricity in the battery during day time and
supplies the same to the load (mainly lamp) at night. On the other hand, if battery is
fully charged,
Then charge controller can directly supply electricity to the load (Fan, mobile charger
etc) from the solar panel during day time.
A charge controller or charge regulator is mainly worked as a voltage regulator.
Generally it controls the voltage and current of the solar panel to save in battery. Solar
panel mainly produces 16 volts to 21 volt and 14 volt to 14.4 volt is required to keep
the battery in full charged state. The charge controller woks as a Buck converter to
minimize this voltage level. Charge controller is mainly a Chopper or DC-DC
converter. Buck converter is usually used in the solar panel which converts the high
level DC voltage to the low level DC voltage.
5.2.2 Block diagram of processing of charge controller:

12V photovoltaic array
Charge controller
Optional
remote
telemetry
Temperature
compensation
probe
Optional
lightning
control
12V battery storage
Optional inverter
DC
loads
Trans
mission
Lighting
loads
AC
loads
Figure: Block diagram of processing of charge controller
5.2.3 Types of Charge controller:

Charge controller connection mainly two types1. Parallel or shunt controller
2. Series controller
5.2.3.1 Parallel Controller:
Figure: Use of Shunt controller in solar home system

In this system, charge controller is in parallel with the battery and load. When the
battery is fully charged, then the solar panel is short circuited by the controller.
In this system, a Blocking diode is needed. So that reverse current would not flow
from battery to the panel. When the battery is charged through this blocking diode, it
gets hot.
Disadvantages of shunt controller:
Lose of electricity
When the panel is short circuited, huge amount of short circuit current (Isc)
flows through the switch (FET).
Shunt controller gets hotter compared to series controller.
There is a chance of hot spot on the panel.
5.2.3.2 Series Controller:
Figure: Use of Shunt controller in solar home system
In this system, charge controller is connected in between with the solar panel and
battery. In order to terminate the flow of electricity to the battery, the series controller
must be removed from the battery. Theres no need of blocking diode in this system,
but in many reasons it is used to terminate the process of discharging at night. The
resistance should be maintained as low as possible in order to minimize lose of the
electricity.
Advantages of series controller:
Blocking diode is not required.
Series controller switch is handled with low voltage compared to shunt
controller.
Low switching noise.
It is possible of precision charge and PWM of the battery.
No chance of hot spot like the shunt controller.
5.2.4 Panel charging and characteristics of controller:
Figure: Relation between different types of charge controller and

battery voltage and current
Above figure shows how different kinds of charge controller controls the voltage and
current. The upper curve shows the battery voltage and the lower curve shows panel
current. a,b,c,d indicates controllers action.
5.2.5 Charge Controller Operation:

Fixed Set Point:
To terminate the panel current when it reaches to the maximum voltage level and then
continue it again when it reaches to the minimum voltage level is called Set point.
The relation between charging-discharging of a battery and voltage is shown in the
figure bellow-
VB
SOC=90%
SOC Calculation
With Fuzzy Logic
SOC=30%
SOC=f(Vb,I;SOC;T;Age;..)
I
L
IS
Figure: Set point of controller (Micro-controller based)
Theres a possibility of the damage of the battery (50-100%) if the voltage level is set
as the red dotted line of the above figure.
We can match the controllers voltage-current with the state of charge (SOC) by using
micro-controller and Fuzz logic. This will reduce the probability of damaging the
battery (10-20%).
5.2.6 Selection of charge controller:

Solid state series controller is suitable for small system (4 ampere). Solid state shunt
controller is suitable for the system of 4 to 30 ampere.
A good controller must have following featuresLow voltage disconnection.
Battery charging current indicator (LED or meter).

Battery voltage indicator (LED or meter).
Sense lead.
Adjustable set point.
Ability of Communication (for large system).
Data logger
Computer interface
.
5.2.7 Voltage setting of controller:

The following factors are responsible for the voltage setting of controllerTypes of battery
Charging characteristics of charge controller
Size of the battery
Maximum panel current
Depth of last charge
Power
MOSFETs
CML PIC
Load LED
SOC LEDs
Charging LED
Figure: A solid state series controller and its various parts
5.2.8 MPPT Charge controller:
MPPT charge controller is a maximum power point tracker which is an electronic DC

to DC converter which takes the DC input from the solar panels, changes it to high
frequency AC and converts it back to a different DC current to match with the
batteries. This is a solely electronic tracking system and not concerned with the panel
system at all.
Figure: Phocos MPPT 100/20(20 amps
5.3 Battery:
5.3.1 Battery Storage:
Batteries are often used in PV systems for the purpose of storing energy produced by
the PV array during the day, and to supply it to electrical loads as needed (during the
night and periods of cloudy weather).
Other reasons batteries are used in PV systems are to
operate the PV array near its
maximum power point, to power electrical loads at stable voltages, and to supply surge
currents to electrical loads and inverters.
In most cases, a battery charge controller is used in these systems to protect the battery
from overcharge and over discharge.
12 volt, 100 Ah solar battery
2 volt, 200 Ah Industrial battery
Figure: Battery
5.4 Inverter:
An inverter is an electrical device that converts direct current (DC) to alternating
current (AC); the resulting AC can be at any required voltage and frequency with the
use of appropriate transformers, switching, and control circuits.
Inverters are commonly used to supply AC power from DC sources such as solar
panels or batteries. The electrical inverter is a high-power electronic oscillator. It is so
named because early mechanical AC to DC converters was made to work in reverse,
and thus was "inverted", to convert DC to AC.
5.4.1 Applications:
An inverter converts the DC electricity from sources such as batteries, solar panels, or
fuel cells to AC electricity. The electricity can be at any required voltage; in particular
it can operate AC equipment designed for mains operation, or rectified to produce DC
at any desired voltage.
Figure: Inverter designed to provide 115 VAC from the 12 VDC source provided in
an automobile. The unit shown provides up to 1.2 Amps of alternating current, or just
enough to power two sixty watt light bulbs
5.4.6 String inverter:
Figure: String inverter

Good look
Available in small- and medium-sized PV power station
User-friendly Interface
Power level 1.5KW to 6KW.
Figure: Power plant inverter
5.4.7 Power plant inverter:

Professional design for large-sized PV power station
Transformer type and transformer less type
Satisfy different requirement, predigest design of power station
5.4.8 Grid tie inverter:

A grid-tie inverter or a (GTI) is a special type of Inverter (electrical) that is used in a
renewable energy power system to convert direct current into alternating current and
feed it into the utility grid. The technical name for a grid-tie inverter is "gridinteractive inverter". They may also be called synchronous inverters. Grid-interactive
inverters typically cannot be used in standalone applications where utility power is not
available.
Figure: Inverter for grid connected PV
Chapter 6
Solar System Design
6.1 Solar home system design:
Basic Components:
1.
2.
3.
4.
Module
Battery
Charge Controller
Load
Figure: A typical solar home system design
6.1.1 Flow chart of solar home system design process:

Start
Screening
of the site
Yes
SHS
suitable?
No
New
site
No
Load analysis
Battery sizing
Sizing of the system
Selecting the components

Charge controller unit
DC-AC converter /
DC-DC converter
Detail design
End
The process of solar home system design is shown in the above flow chart. The
process is started with the site screening. It means that it must be located in a place
where there is enough sunlight. Then first stage is load estimation and after that battery
sizing. Then other components of the system such as charge controller unit and voltage
converter (if needed) are selected. In this way, the whole system design is processed.
But one thing must be remembered that Infrastructure Development Company Limited
(IDCOL) has published some standard for solar system design in Bangladesh. A
designer must have knowledge about that.
6.1.2 Site screening:

In this part of the design, we will first analysis the location of the installation of the
solar system where there is available sunshine. As we know sunshine isnt equal in all
places so this part very important. Because the price of the whole system depends on
it.
6.1.3 Load determination:

To find out the daily average load, we need some calculation. For example, a family
consists of five persons using TV for 2 hours, three Fluorescent lamps for 5 hours,
Video cassette player for 1.5 hours daily.
So power requirement of various types of loads are given bellow:
Item /loads
TV
Fluorescent lamp
Radio
Video cassette player
Rated power
25W
15W
12W
12W
Solution: The daily energy needed for the given family =

2*25+2*12+3*5*15+1.5*12=317Wh
6.1.4 Battery sizing:

The following characteristics are needed for a solar home system battery:
For deep cycle, long lifetime
Low maintenance
High charging capacity
The ability of completely discharge
Low internal discharging rate
Reliability
Minimum change under excessive temperature
6.1.5 Array sizing:

Array sizing of a PV system means the calculation of the number of PV modules.
6.1.6 Selection of charge controller:

Functional parameter of solar home system charge controller
Maximum current receive from PV panel
Ability of maximum power supply on the load
Mark it low voltage level
Mark it high voltage level
Electric protection from thunder
Good regulation
Protection from reverse polarity
Adjust with system voltage
6.1.7 Selection of converter:

A solar home system use for appliance needs ac and dc voltage. As Solar module
output voltage is dc, so this system dc-dc converter or dc-ac converter needed. Some
of the load is connected necessary converter.
6.1.8 System wiring:

From PV module up to system component electric wiring is needed. Voltage drop
occurs in internal resistance of the wire. Solar home system this voltage drop should
keep under a limit.
Wire cost is very important and wire length must be small size. Connection the solar
component under dement must be fulfill:
System must be safe
These wire are not make defect for system components performance
Each components works according their maximum performance
If possible use centralized 12volt dc system
If possible use centralized 24volt dc system
Wire Standard Size :

Cross sectional
area(mm)
1.0
1.5
2.5
4.0
Wire Gauge(AWG or
SWG)
18
16
14
12
Current Rating (A)
6.0
10.0
16.0
25.0
10
8
6
4
35
50
70
90
10
15
20
30
Maximum length of wire for 0.6 volt drop in 12 volt system:

Cable
Maximum cable Length (m) for various load Requirement
size(mm)
Load
24
36
48
60
72
96
power(w)
Current at 2
3
4
5
6
8
12 v (A)
1.5
12
8
7
5
5
4
2.5
20
13
10
8
7
6
4.0
31
21
16
13
11
8
6.0
46
31
23
19
16
12
10
76
51
38
31
26
20
120
10
3
5
7
10
16
Maximum length of wire for 1.2 volt drop in 12 volt system:
Cable
Maximum cable Length (m) for various load Requirement
size(mm)
Load
48
72
96
120 144 192
power(w)
Current at 2
3
4
5
6
8
12 v (A)
1.5
23
16
12
10
8
7
2.5
38
26
20
16
13
10
4.0
61
41
31
25
21
16
6.0
91
61
46
37
31
23
10
151
101
76
61
51
38
240
10
5
8
13
19
31
6.1.9 A small size 12 volt home system Design:

Let, according to under table for 90Wh/day design a 12 volt solar home system. Here
40Wp module (Isc = 2.54a, Imp = 2.31A & nominal voltage = 12) and 12volt, 55 Ah
battery (DOD = 60%, Efficiency = 80%) will use. Here must remain low cost battery
&module will used.
Load
type(230 AC
load)
Fluorescent
lamp
TV 14
Total
Device
watts(w)
Daily use
(hours)
No. of unit
Total watts
7.5
22.5
Total watthours per

day
67.5
15
1.5
15
37.5
22.5
90
IEE & NSE standard solar home system cabal voltage drop maximum 5%
So, maximum power loss 5%
And inverter efficiency 90%
Battery sizing:
90
DC Wh/day = --------------- =105.26
0.9*0.95
105.26
Daily load Ah = --------- =8.77 Ah
12v
Battery efficiency = 80%
DOD = 60%
If autonomy of battery 3 day
8.77*3
So Amp-hour for battery = ---------- = 54.8 Ah
0.6*.08
As battery voltage is 12 volt and system volage is 12 volt, and output of battery is 55
Ah then here one battery is needed.
Array sizing:
Daily PV module output = 12*2.31*4.2
= 116.42 Ah
Daily avg. pick insulation = 4.2 hours
Summarizing 20% loss PV array sizing

So this system requirement DC watt-hours = 105.26 Wh/day
105.26
So no. of module =--------------- = 1
116.42*.8
Charge controller size
Given Isc = 2.54A
Charge controller design current = 1.25*2.54A = 3.175A
37.5
Maximum DC current =---------- =3.47A
12*0.9
Here needed charge controller rating = 3.5A
Wire size:
Design current = 3.17A
Maximum load current = 3.47A
Current from PV module to charge controller = 3.175*1.25 = 4.0A
So, wire size 1.0mm
6.1.10 a big size 24 volt home system Design:

Let, according to under table for 2090Wh/day design a 24 volt solar home system.
Here 50Wp module (Isc = 3.22A, Imp = 2.94A & nominal voltage = 12) and 2volt,
660 Ah battery (DOD = 60%, Efficiency = 80%) will use. Here must remain low cost
battery &module will used.
Load
type(230
AC load)
CFL
TV 14
color
Computer
Mobile
charger
Fan
Total
Device
watts(w)
Daily use
(hours)
No. of unit
Total watts
11
60
5
3
6
1
66
60
Total watthours per

day
330
180
400
4
2
4
1
4
400
16
800
64
60
120
662
720
2090
IEE & NSE standard solar home system cabal voltage drop maximum 5%
So, maximum power loss 5%
And inverter efficiency 90%
All appliance input voltage = 230volt
Battery size
2090
DC Wh/day = --------------- =2444Wh
0.9*0.95
2444Wh
Daily load Ah = --------- =102Ah
24v
Battery efficiency = 80%
DOD = 60%
If autonomy of battery 3 day
102*3
So Amp-hour for battery = ---------- = 638Ah
0.6*0.8
As battery voltage is 2 volt and system voltage is 24 volt,
So 12 battery are needed
Output of battery is 660 Ah
Battery requirement 638Ah
Array sizing
Daily PV module output = 12*2.94*4.2
= 148.2 Ah
Module nominal voltage = 12V
Daily avg. pick insulation = 4.2 hours
Summarizing 20% loss PV array sizing
So this system requirement DC watt-hours = 2444Wh/day
2444
So no. of module =--------------- = 21
148.2*0.8
For getting 24V, 2 no of module connect in series and like this 11 no of set connect in
parallel are needed
Charge controller
Given Isc = 3.22A

Total short circuit current = 11*3.22A = 35.42A
Charge controller design current = 1.25*35.42A = 44.275A
662
Maximum DC current =---------- =31A
12*0.9
Here needed charge controller rating = 45A
Inverter size
Size of the inverter = 662/(.9) *1.25= 920W
So 1.0KW inverter is needed
Wire size
Design current (PV array to charge controller)= 44.275A
Maximum load current (charge controller to inverter) = 33A
Current from PV module to charge controller = 44.275*1.25 = 55.34A
So, wire size 16mm
6.1.11 Design of 50 watt solar PV system:

Array sizing:
If energy demand is 50W, Rate of insulation is 4.2 KW/m and efficiency is 0.7 then,
The size of module = 50/(4.2* 0.7 )=17W
But 17W module is not available. So we need 50Wp PV module.
No of PV module:
If, per day energy output is Pdm, module output voltage is Vmm and current is ILm then,
Per day energy output is,
Pdm=ILm*D*Vmm
No of module
Nm=PAR/Pdm
Where,
Nm= No of module
PAR= Per day energy requirement
Battery sizing:
If the system voltage 12V, Battery depth of discharges 70% and autonomy 3 days then
we need, we know,
P=VI
If energy demand is 50WH, then,
For, 12 volts battery, we need power= 50WH/ 12V = 4.16Ah
Autonomy of 3 days, So 4.16*3 = 12.48 Ah
But, depth of discharge is 75%
So, power = 12.48Ah/(0.75*0.8) = 20.8Ah[If efficiency is 80%]
So, we need to battery those absorbed of capacity is 21 Ah
So, we need = 21 /100 = 0.21 = 1 battery
Standard size of wire:
For the wire selection we need to concentrate below the characteristic:
Length of wire
Wire receptivity
Cross sectional area of wire
Flow of electricity of wire
If, L = length
I = Amperes,
= Receptivity,
a = Area of wire,
Then,
Voltage drop, Vd = 2LI /a
Where,
= 0.0183 /m /mm

Array sizing:
The size of module = 60/(4.2* 0.7 )=20.40W

No of PV module:
Pdm=ILm*D*Vmm
No of module
Nm=PAR/Pdm
Where,
Nm= No of module
PAR= Per day energy requirement
Battery sizing:
we need, we know,
P=VI
For, 12 volts battery, we need power= 60WH/ 12V = 5 Ah
Autonomy of 3 days, so 5* 3 = 15 Ah
So, power = 15 Ah / (0.75*0.8) = 25 Ah [If efficiency is 80%]
Length of wire
Wire receptivity
If, L = length
I = Amperes,
= Receptivity,
a = Area of wire,
Then,
Voltage drop , Vd = 2LI /a
Where,
= 0.0183 /m /mm

Array sizing:
The size of module = 110/ (4.2* 0.7) =37.41W
No of PV module:
Pdm=ILm*D*Vmm
No of module
Nm=PAR/Pdm
Where,
Nm= No of module
PAR= per day energy requirement
Battery sizing:
we need, we know,
P=VI
For, 12 volts battery, we need power= 110WH/ 12V = 9.167Ah
Autonomy of 3 days, so 9.167* 3 = 27.5 Ah

So, power = 27.5 Ah / (0.75*0.8) = 45.83 Ah [If efficiency is 80%]
So, we need to battery those absorbed of capacity is 45.83 Ah
So, we need = 45.83 /100 = 0.458 = 1 battery
Length of wire
Wire receptivity
If, L = length
I = Amperes,
= Receptivity,
a = Area of wire,
Then,
Where,
= 0.0183 /m /mm

Array sizing:
The size of module = 85/ (4.2* 0.7) =28.91W
No of PV module:
Pdm=ILm*D*Vmm
No of module
Nm=PAR/Pdm
Where,
Nm= No of module
PAR= per day energy requirement
Battery sizing:
we need, we know,
P=VI
For, 12 volts battery, we need power= 85WH/ 12V = 7Ah
Autonomy of 3 days, so 7 * 3 = 21 Ah
So, power = 21 Ah / (0.75*0.8) = 35 Ah [If efficiency is 80%]
Length of wire
Wire receptivity
If, L = length
I = Amperes,
= Receptivity,
a = Area of wire,
Then,
Where,
= 0.0183 /m /mm
Chapter 7
Software of Solar Energy in Bangladesh
7.1 Project:
A specific complex and time bound set of tasks or activities undertaken to achieve a
given objective according to a defined budget and timetable.
7.2 Program:
A combination of personnel, facilities, money, equipment, supplies and other items
directed to accomplish a specific objective. It is a cluster of project.
7.3 Activity or a Task:

It is a very short term effort performed by one or several members of a project team
7.4 Project categories:

Project may be categorized in-terms of number of context and some of these are:
A. According to objective
Social project
Development project
Economic growth oriented project
B. According to sector
Agricultural project
Educational project
Health project
C. According to purpose
Single purpose project
Multi purpose project
D. According to relationship with other project
Mutually exclusive project
Independent project
Complementary project
7.7 Project Design:

Project design is an offshoot of two stages comprised of the following:
Identification of project ideas to to resolve the priority problems.
Preliminary selection of a project concept and of alternative design approaches
as suitable for further feasibility
7.8 Aspect of Project Preparation and Analysis:

Following are the different aspects of project preparation and analysis:
1. Market and commercial aspects
2. Technical aspects
3. Institutional-Organizational-Managerial Aspects
4. Socio Economic aspects
5. Financial aspects
6. Economic aspects
7.10 Identifying Direct Costs:

Direct costs items are usually classified into two types:
A. Capital costs
B. Operating and maintenance Costs
7.10.1 Capital costs:

Land and other natural resources that have current
alternative uses
Detailed engineering and design

Preparatory installation work
Cost of equipment, raw materials and supplies for construction
Cost of building and auxiliary installations
Engineering and administrative cost during construction
Organization costs
Expenses of running in periods
Contingencies
7.10.2 Operating and maintenance Cost:

Raw materials and other supplies
Energy and Fuels
Labor
Rent and Insurance
Depletion of natural resources
Contingencies
The above mentioned items are identified in the technical study and should also
be reflected in the financial analysis
Sunk Cost
These are those costs which have been incurred on the project before its
appraisal.
Shadow prices
These prices are the values of project inputs and out puts reflecting their
relative scarcity or availability.
Suppose that the economic value of foreign exchange is 20% higher than the
official rate for the Taka. If the official rate is US$ 1 = Tk-68.00 then the
shadow price is (1.2 x 68) = Tk- 81.60 for each dollar.
7.13 Solar Power System (100w-h):

Details of cost involved in a 100-w-h solar power system are:
Sl.#
Description of item
Tk.
1.
Solar panel (100 w-h)
24,500.00
2.
Battery 150 AmH
12,000.00
3.
Charge controller
2,000.00
4.
Wiring
2,000.00
5.
Panel mounting
2,000.00
6.
Miscellaneous
1,000.00
Total Tk-
45,500.00
7.15 Software & data:
In RETScreen Version 4, the software's capabilities have been expanded from

renewable energy, cogeneration and district energy, to include a full array of
financially viable clean power, heating and cooling technologies, and energy
efficiency measures.
7.16. Five step standard analysis:
Chapter 7
Field Work
Solar Energy:
Data from Center for Solar Energy Studies, AUST, Dhaka
File Name:;CX
Date of Reading:24-10- 2009 12:57:23 PM
Location: Dhaka, Bangladesh
Latitude: 23 43 23
Charge Controller Identification: Phocos CX, 12V
Battery capacity: 12V, 135Ah
PV Power:85 Watt
General Data logger Data:

Number of low battery load disconnects: 11
Number of weeks without fully charged battery: 6
Number of months without fully charged battery: 0

Average battery state in the mornings in %: 85
Used PV Ampere hours: 2756
Load Ampere hours: 2597
Start Of Recording (Days): 371
Day:
14.4
12 .2
14.2
12 .1
12
14
11.9
13.8
Volt11.8
Volt 13.6
11.7
13.4
11.6
13.2
11.5
13
11.4
Day
Fig:1 Maximum Battery Voltage Day
Maximum Voltage
12
Minimum Voltage
10
Volt
8
6
4
2
0
1
Day
Fig: 2 Minimum Battery Voltage Day
16
14
Day
Fig: 3 Maximum and Minimum Battery Voltage Day
PV Ah
10
20
18
16
14
12
Load Ah
Ah
Ah 10
0
1
Day
7.4
7.2
Day
Fig: 5 PV Excess Ampere hours
Fig: 4 PV and Load Ampere hours
6.8
6.6
6.4
6.2
0
1
Day
Fig: 6 Maximum Load Current in A
Day
Fig: 7 Maximum PV Current in A
100
100
98
98
96
96
94
94
Charge92
90
in % 88
Charge
in %
92
90
88
86
86
84
84
82
82
80
1
80
Day
Fig: 8 State of Battery Charge in %
Morning and Evening
Low Battery Disconnect

Full Charge Battery
PV over current
Load over current
Battery Over voltage
PV Over temperature
Load Over temperature
1
False
True
False
False
False
False
False
Day
Fig: 9 Charge State of Battery
Morning and Evening
2
False
True
False
False
False
False
False
Day
3
False
True
False
False
False
False
False
4
False
True
False
False
False
False
False
5
False
True
False
False
False
False
False
6
False
True
False
False
False
False
False
7
False
True
False
False
False
False
False
Week:
14.6
12.2
14.4
12
14.2
Volt
Volt
14
11.8
11.6
13.8
11.4
13.6
11.2
13.4
11
13.2
10.8
10.6
13
1
Week
Fig 10: Max. Battery Voltage
Week
Fig 11: Min. Battery Voltage
16
14
12
10
Volt 8
6
4
2
0
1
Week
Fig12: Max and Min Voltage
9.2
25
9
8.8
20
PV Ah
8.6
Amp15
8.4
Amp8.2
10
Load Ah
7.8
7.6
7.4
1
Week
Fig 13: PV and Load Ampere hours
0
1
Week
Fig 14: PV Access Ampere-hour
1.8
1.6
1.4
1.2
Current 1
in A 0 .8
Current
in A
5
4
3
0 .6
0 .4
0 .2
0
1
Week
Fig 15 : Maximum Load Current in A
Week
Fig 16: Maximum PV Current in Amp
120
10 0
100
90
Charge
in %
80
80
Charge
in % 60
70
60
50
40
40
30
20
20
10
0
1
Week
Fig 17: Charge State of Battery in
Morning & Evening in %
Low Battery Disconnect

Full Charge Battery
PV over current
Load over current
PV Over temperature
Load Over temperature
1
False
True
False
False
False
False
False
Week
Fig 18: Charge State of Battery in
Morning & Evening in %
2
False
True
False
False
False
False
False
Week
3
False
True
False
False
False
False
False
4
False
True
False
False
False
False
False
Month:
14.1
12.4
14
12.35
13.9
12.3
12.25
13.8
Volt
Volt
13.7
12.2
12.15
13.6
12.1
13.5
12.05
13.4
12
13.3
11.95
9 10 11 12
Month
Fig 19: Max. Battery Voltage
14.5
9 10 11 12
Month
Fig 20: Min. Battery Voltage
Max. Voltage
14
13.5
Volt
13
12.5
12
Min. Voltage
11.5
12
11
10
11
Month
Fig 21: Max. & Min. Battery Voltage Each Month
PV Current
10
25
9
8
20
Current
Current 15
6
5
Load Current
10
3
2
0
1
9 10 11 12
Month
Fig 22: PV & Load Ampere-hours
9 10 11 12
Month
Fig 23: PV Access Ampere-hours
1.8
1.6
1.4
1.2
Current
Current
0.8
0.6
0.4
0.2
0
1
10 11 12
Month
Fig 24: Max. Load Current in Amp.
9 10 11 12
Month
Fig 25: Max. PV Current in Amp.
100
80
60
% of Charge
40
20
0
1
10 11 12
Month
Fig 26: Charge State of Battery in Morning & Evening in %
120
Evening Charge
100
80
% of Charge 60
Morning Charge
40
20
Month
Fig 27: Charge State of Battery in Morning & Evening in %
12
11
10
Low Battery
Disconnect
Full Charge Battery
PV over current
Load over current
PV Over temperature
Load Over
temperature
1
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse
2
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse
3
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse
4
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse
5
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse
6
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Month
7
8
Fal Fa
se
lse
Tru Tr
e
ue
Fal Fa
se
lse
Fal Fa
se
lse
Fal Fa
se
lse
Fal Fa
se
lse
Fal Fa
se
lse
9
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse
10
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse
11
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse
12
Fa
lse
Tr
ue
Fa
lse
Fa
lse
Fa
lse
Fa
lse
Fa
lse

Chapter 1

Uploaded by

Copyright:

Available Formats

Chapter 1

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 1

Uploaded by

Copyright:

Available Formats

Chapter-1

1.2 Definition of Energy:

1.3 Renewable Energy

Main forms/sources of renewable energy

1.4 Types of Renewable Energy:

Photovoltaic (PV) Cells:

1.5 Advantages of Renewable Energy:

2.2 Present Scenario of Conventional and renewable energy

Total insulated power in grid

Total insulated power off grid electricity

2.3 Significant Progress of

Renewable Energy Technology in

365,000 SHS and

2.4 Government Support in Renewable Energy Sector in

Government setup a target that at least 5% electricity by

Duty & VAT

Government wipe out all sort of duty from renewable

Tax Holiday (according to According to declared RE policy, Renewable energy

Manufacturing plant for

Duty of capital machinery for assembling of PV module is

2.5 Ongoing Renewable Energy Technology (RET)

3.1 Definition of Energy:

3.2 Types of Energy:

3.4 Surface temperature:

3.5 Conversion of sunlight into electricity:

Sun -Earth relation-1

3.6 Extraterrestrial radiation:

.Infrared region (l > 0.78mm) percentage ration 45.7%

Figure: Extraterrestrial radiation

Extraterrestrial radiation at any time of the year is given by

3.7 Equation of time:

229.2(0.000075+0.001868 B- 0.032077 sin B - 0.014615 cos 2B-

3.8 Solar Energy Spectrum:

Figure 2: Spectrum of Solar Radiation

Solar energy uses in various respects. Such as;

Generate electricity using photovoltaic solar cells.

Solar air conditioning.

4.2 Solar Photovoltaic:

4.2.2 Advantages of Photovoltaic:

Fuel source of photovoltaic is vast and essentially infinite.

Low operating cost.

4.3 Solar Heating:

4.3.1 Solar Heating Basics:

Figure: These solar collectors are part of

4.3.2 Solar Heating in Use:

4.4 Solar Thermal Electricity:

Figure 2.5: Curved mirror to produce electricity

4.5 Solar Cooking:

Figure 2.6: Solar cooking dish

4.6 Solar Water Heater:

Figure 2.4: Solar water heating mechanism

4.7 Solar dryer:

4.7.1 Solar dryer Application:

4.7.2 Solar Drying Can Improve Agricultural Products:

(d) MIS (Metal / Isolator / Semiconductor

5.1.1 Connect cell to make modules:

Figure: Cells, Modules, Panels and Arrays

5.1.2 Types of Solar Cells: