Lte Ofdm, Ofdma and Sc-Fdma

LTE OFDM, OFDMA and SC-FDMA
One of the key elements of LTE is the use of OFDM (Orthogonal Frequency Division
Multiplex) as the signal bearer and the associated access schemes, OFDMA
(Orthogonal Frequency Division Multiplex) and SC-FDMA (Single Frequency Division
Multiple Access).
OFDM is used in a number of other of systems from WLAN, WiMAX to broadcast
technologies including DVB and DAB. OFDM has many advantages including its
robustness to multipath fading and interference. In addition to this, even though, it
may appear to be a particularly complicated form of modulation, it lends itself to
digital signal processing techniques.
In view of its advantages, the use of ODFM and the associated access technologies,
OFDMA and SC-FDMA are natural choices for the new LTE cellular standard.
OFDM basics
The use of OFDM is a natural choice for LTE. While the basic concepts of OFDM are
used, it has naturally been tailored to meet the exact requirements for LTE.
However its use of multiple carrier each carrying a low data rate remains the same.
Note on OFDM:
Orthogonal Frequency Division Multiplex (OFDM) is a form of transmission that uses a
large number of close spaced carriers that are modulated with low rate data. Normally
these signals would be expected to interfere with each other, but by making the signals
orthogonal to each other there is no mutual interference. The data to be transmitted is
split across all the carriers to give resilience against selective fading from multi-path
effects..
Click on the link for an OFDM tutorial
The actual implementation of the technology will be different between the downlink
(i.e. from base station to mobile) and the uplink (i.e. mobile to the base station) as
a result of the different requirements between the two directions and the
equipment at either end. However OFDM was chosen as the signal bearer format
because it is very resilient to interference. Also in recent years a considerable level
of experience has been gained in its use from the various forms of broadcasting
that use it along with Wi-Fi and WiMAX. OFDM is also a modulation format that is
very suitable for carrying high data rates - one of the key requirements for LTE.
In addition to this, OFDM can be used in both FDD and TDD formats. This becomes
an additional advantage.
LTE channel bandwidths and characteristics

One of the key parameters associated with the use of OFDM within LTE is the choice
of bandwidth. The available bandwidth influences a variety of decisions including
the number of carriers that can be accommodated in the OFDM signal and in turn
this influences elements including the symbol length and so forth.
LTE defines a number of channel bandwidths. Obviously the greater the bandwidth,
the greater the channel capacity.
The channel bandwidths that have been chosen for LTE are:
1. 1.4 MHz
2. 3 MHz
3. 5 MHz
4. 10 MHz
5. 15 MHz
6. 20 MHz
In addition to this the subcarriers are spaced 15 kHz apart from each other. To
maintain orthogonality, this gives a symbol rate of 1 / 15 kHz = of 66.7 s.
Each subcarrier is able to carry data at a maximum rate of 15 ksps (kilosymbols per
second). This gives a 20 MHz bandwidth system a raw symbol rate of 18 Msps. In
turn this is able to provide a raw data rate of 108 Mbps as each symbol using
64QAM is able to represent six bits.
It may appear that these rates do not align with the headline figures given in the
LTE specifications. The reason for this is that actual peak data rates are derived by
first subtracting the coding and control overheads. Then there are gains arising
from elements such as the spatial multiplexing, etc.
LTE OFDM cyclic prefix, CP

One of the primary reasons for using OFDM as a modulation format within LTE (and
many other wireless systems for that matter) is its resilience to multipath delays
and spread. However it is still necessary to implement methods of adding resilience
to the system. This helps overcome the inter-symbol interference (ISI) that results
from this.
In areas where inter-symbol interference is expected, it can be avoided by inserting
a guard period into the timing at the beginning of each data symbol. It is then
possible to copy a section from the end of the symbol to the beginning. This is
known as the cyclic prefix, CP. The receiver can then sample the waveform at the
optimum time and avoid any inter-symbol interference caused by reflections that
are delayed by times up to the length of the cyclic prefix, CP.
The length of the cyclic prefix, CP is important. If it is not long enough then it will
not counteract the multipath reflection delay spread. If it is too long, then it will
reduce the data throughput capacity. For LTE, the standard length of the cyclic
prefix has been chosen to be 4.69 s. This enables the system to accommodate
path variations of up to 1.4 km. With the symbol length in LTE set to 66.7 s.
The symbol length is defined by the fact that for OFDM systems the symbol length
is equal to the reciprocal of the carrier spacing so that orthogonality is achieved.
With a carrier spacing of 15 kHz, this gives the symbol length of 66.7 s.
LTE OFDMA in the downlink

The OFDM signal used in LTE comprises a maximum of 2048 different sub-carriers
having a spacing of 15 kHz. Although it is mandatory for the mobiles to have
capability to be able to receive all 2048 sub-carriers, not all need to be transmitted
by the base station which only needs to be able to support the transmission of 72
sub-carriers. In this way all mobiles will be able to talk to any base station.
Within the OFDM signal it is possible to choose between three types of modulation:
1. QPSK (= 4QAM)
2 bits per symbol
2. 16QAM
4 bits per symbol
3. 64QAM
6 bits per symbol
The exact format is chosen depending upon the prevailing conditions. The lower
forms of modulation, (QPSK) do not require such a large signal to noise ratio but
are not able to send the data as fast. Only when there is a sufficient signal to noise
ratio can the higher order modulation format be used.
Downlink carriers and resource blocks

In the downlink, the subcarriers are split into resource blocks. This enables the
system to be able to compartmentalise the data across standard numbers of
subcarriers.
Resource blocks comprise 12 subcarriers, regardless of the overall LTE signal

bandwidth. They also cover one slot in the time frame. This means that different
LTE signal bandwidths will have different numbers of resource blocks.
Channel bandwidth
1.4
10
15
20
15
25
50
75
100
(MHz)
Number of resource blocks
LTE SC-FDMA in the uplink

For the LTE uplink, a different concept is used for the access technique. Although
still using a form of OFDMA technology, the implementation is called Single Carrier
Frequency Division Multiple Access (SC-FDMA).
One of the key parameters that affects all mobiles is that of battery life. Even
though battery performance is improving all the time, it is still necessary to ensure
that the mobiles use as little battery power as possible. With the RF power amplifier
that transmits the radio frequency signal via the antenna to the base station being
the highest power item within the mobile, it is necessary that it operates in as
efficient mode as possible. This can be significantly affected by the form of radio
frequency modulation and signal format. Signals that have a high peak to average
ratio and require linear amplification do not lend themselves to the use of efficient
RF power amplifiers. As a result it is necessary to employ a mode of transmission
that has as near a constant power level when operating. Unfortunately OFDM has a
high peak to average ratio. While this is not a problem for the base station where
power is not a particular problem, it is unacceptable for the mobile. As a result, LTE
uses a modulation scheme known as SC-FDMA - Single Carrier Frequency Division
Multiplex which is a hybrid format. This combines the low peak to average ratio
offered by single-carrier systems with the multipath interference resilience and
flexible subcarrier frequency allocation that OFDM provides.

Lte Ofdm, Ofdma and Sc-Fdma

Uploaded by

Copyright:

Available Formats

Lte Ofdm, Ofdma and Sc-Fdma

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lte Ofdm, Ofdma and Sc-Fdma

Uploaded by

Copyright:

Available Formats

LTE OFDM, OFDMA and SC-FDMA

Click on the link for an OFDM tutorial

LTE channel bandwidths and characteristics

LTE OFDM cyclic prefix, CP

LTE OFDMA in the downlink

2 bits per symbol

4 bits per symbol

6 bits per symbol

Downlink carriers and resource blocks

Resource blocks comprise 12 subcarriers, regardless of the overall LTE signal

LTE SC-FDMA in the uplink

You might also like