Determining Energy Production of Cdte Photovoltaic System: Abstract

Jan LAMBERGER1, Peter VIRTI1
University of Maribor, Faculty of Energy Technology (1)
Determining energy production of CdTe photovoltaic system

Abstract. This paper presents a method for determining energy production of Cadmium-Telluride photovoltaic system, which has a different working
performance than the most used Silicon photovoltaic systems. The main difference is sensitivity to the temperature and the solar irradiance. The
CdTe cells are less sensitive to the temperature and in contrast to the Si Cells they have a higher efficiency at lower irradiance.
Streszczenie. W artykule przedstawiono metod wyznania energii wytworzonej przez system paneli fotowoltaicznych z tellurku kadmu (CdTe),
rnicych si od klasycznych krzemowych. Gwnymi rnicami midzy nimi jest wraliwo na zmiany temperatury i nasonecznienia, gdzie
system CdTe wykazuje mniejsz wraliwo na temperatury natomiast Si wysz sprawno przy niskim nasonecznieniu. (System fotowoltaiczny
CdTe wyznaczanie wytwarzanej energii).
Keywords: photovoltaic module, energy production, annual energy yield, Cadmium-Telluride.

Sowa kluczowe: panel fotowoltaiczny, wytwarzanie energii, roczna wydajno energetyczna, tellurek kadmu.
Introduction
One of the most important parameters in the recovery of
investment costs of photovoltaic (PV) power plant is the
energy yield, which tells how much electrical energy the
plant will produce in a given period. The energy yield
generally depends on four elements: the components of the
plant, the plant location, the weather and the losses.
The basic components of the photovoltaic systems are
photovoltaic modules, inverters and cables. For better
energy yield the components with high quality have to be
chosen, because the PV power plant will operate for many
decades. Besides the guarantee of the modules operation
the classifying to the classes and subclasses has an
important role as well. The entire branch of the modules will
work as the worst module. For more accurate calculation of
energy yield, it is important to know the PV module
performance [1, 2]. It is also important to be careful with the
choice of inverters and cables. By the inverters the
maximum power, the maximum permissible voltage, the
maximum permissible current and the conversion efficiency
have important role. By the cables a comparison between
the losses and price has to be done. In practice, the cables
are determined to have the voltage drop less than 1% [3].
For better energy yield the fixed PV plant must be
oriented to the south with the tilt that is closest to the
optimal tilt for a given area. The optimal tilt fixed power
plant for Slovenia is around 30 [3]. Even greater energy
yield could be achieved with sun tracking systems. With the
optimal regulation, the annual energy yield will increase for
approximately 40% to 50% [4]. It must be ensured that the
PV modules are not shadowed in any season. By setting up
the modules on the roof, the sufficient cooling of modules
must be ensured, which means that the air bridge between
the roof and the modules has to be built.
The energy yield is strongly associated with the weather
because the electrical energy is produced directly from the
solar energy. The exact weather cannot be predicted in the
form of equations and it can be calculated only for clear
days [5] or be predicted from long-term averages,
minimums and maximums. The weather data can be
obtained from various databases. The most accurate data
can be obtained from the meteorological data stations, of
course, if they are in the vicinity of the plant location.
Otherwise
the
interpolation
of
several
remote
meteorological data stations or a satellite images has to be
used. Of the last two the satellite pictures are more
accurate, but generally they give average values between
two meridians and two parallels. The data from various
databases can vary up to 10%.
84
Energy yield of PV system is, beside the meteorological

data, strongly connected with the losses. As a source of the
energy, the solar radiation on a horizontal surface of the
earth will be taken. After that the losses follow in
subsequent order:
losses due to the inclination of the surface (to the south
orientations are generally increments);
losses due to reflection on the glass of module;
losses due to glass contamination (dust, snow);
losses due to temperature;
losses due to irradiance;
losses resulting from the conversion of solar energy into
electricity;
losses due to mismatch of the power of modules;
losses due to mismatch of the characteristics of
modules in branches;
losses in the wires on the DC side;
losses resulting from the conversion of DC voltage into
AC voltage;
losses in the wires on AC sides.
All these losses can be divided into two groups. The first
group contains losses, which can be accurately determined
at any time. These are losses due to the inclination of the
surface, losses due to reflection on glass modules, losses
due to temperature, losses due to irradiance, losses in the
conversion of solar energy into electrical energy, losses in
the wires on the DC side, losses in the conversion of DC
voltage into AC voltage and losses in the wires on AC side.
The second group contains losses that cannot be
accurately measured, but can be based on experience and
determined assumptions. These are losses due to
contamination of glass, loss of power due to the mismatch
of modules and loss due to mismatch of connected modules
in the branches. When calculating the energy yield the
maximum values of losses have to be considered.
Table 1. The nominal data for module FS-277
Nominal power (5%)
Pmpp [W]
Voltage at maximum-Power
Vmpp [V]
Current at maximum-Power
Impp [A]
Open Circuit Voltage
Voc [V]
Short Circuit Current
Isc [A]
Temperature Coefficient of Current
i [%/C]
Temperature Coefficient of Voltage
v [%/C]
Normal Operation Cell Temperature
Tc,NOCT [C]
77,5
69,9
1,11
90,5
1,22
0,04
-0,25
45
PV module performance
In order to prescribe the PV module performance, the
test under real conditions must be made. Based on the
results of the test, the coefficients of equation (1) [1] are
determined. The CdTe PV module type FS-277 of the First
PRZEGLD ELEKTROTECHNICZNY, ISSN 0033-2097, R. 89 NR 2b/2013
0.6
0.4
I mpp [A]
0.2
200
400
600
800
1000
Solar irradiance on the plane =30 =0 [W/m2]
Voltage and power in

the maximum-power point
80
70
60
70
Power in the maximum-power

point Pmpp [W]
0.8
Fig.1. The current in the maximum-power point
60
50
40
30
Measurements
PVsyst
Fitting
20
10
0
0
50
200
40
30
Umpp [V]
20
10
0
Pmpp [W]
200
400
600
800
1000
Fig.2. The voltage and the power in the maximum-power point

Temperature of the ambient and
temperature of the PV module
Table 2. The coefficients of the equation of the PV module

performance
2
Coefficient
C0 [ ]
C1 [ ]
C2 [1/V]
C3 [1/V ]
Value
0,7761
0,1093
-0,1363
-1,032
Figures 4 and 5 show the comparison between the results

of the measurements, the equation (1) and the commercial
software package for calculating the energy yield of PV
systems PVsyst. The relative efficiency is the ratio between
the efficiency by the real conditions and efficiency by the
standard test conditions (2).
60
50
Tamb [C]
Tmod [C]
40
30
400
600
800
Solar irradiance [W/m2]
1000
Fig.4. The power in the maximum-power point at the real conditions
rel
(2)
Pm GSTC A
Gc A PSTC
where: A surface area of the PV module. In comparison to

silicon PV modules, the CdTe PV modules have higher
efficiency at lower solar irradiance. The relative efficiency at
lower solar irradiance is even greater than 100%. The
reason for a big difference between measured values and
values calculated with software PVsyst is in a bad
performance model of CdTe module in PVsyst. The relative
efficiency of CdTe module calculated with PVsyst is similar
to the relative efficiency of silicon modules, where the value
of relative efficiency is lower than 100 %.
120
20
0
200
400
600
800
1000
Fig.3. The temperature of the ambient and the PV module
The equation (1) has been adjusted according to the

results of test. The coefficients of equation (1) are
presented in table 2.
(1)
Gc irradiance on the cell, Tc cell temperature, Ns

number of cells in series, T thermal voltage.
Gc
Gc
Pm PSTC C0
C1
GSTC
GSTC
G
1 i Tc Tc,STC 1 C2 N s T ln c
GSTC
G
C3 N s T ln c
GSTC
v Tc Tc,STC
where: PSTC nominal power by STC, GSTC irradiance by

STC (1000 W/m2), Tc,STC cell temperature by STC (25 C),
Relative efficiency rel [%]
Current in the maximum-power

point
Solar manufacturer was tested under real conditions by

using instrument HT IV-400. The nominal data of tested PV
module are given in table 1.
Figures 1 and 2 show the results of the PV module test.
Figure 3 shows the ambient and module temperature
measured at the time of the test.
Measurements
PVsyst
Fitting
110
100
90
80
70
0
200
400
600
800
Solar irradiance [W/m2]
1000
Fig.5. Relative efficiency at the real conditions
Input data
Values of the solar irradiance on the PV cell and the PV
cell temperature are also required for calculation of the
power of a PV module. Previously mentioned parameters
can be obtained from meteorological data stations, global
irradiance, diffuse irradiance and ambient temperature.
These data are collected for time periods of 15-60 minutes,
depending on the meteorological data station. The solar
irradiance on the module can be calculated with the
following equation [6, 7]:
85
(3)
cos i
1 cos
Gd
Gc Gb
sin
2
G g
1 cos
1
1 b0
2

cos i
where: Gb beam irradiance, Gd diffusive irradiance, Gg

global irradiance, angular height of the sun, tilt of the
module, reflective factor of the surrounding area, b0
reflective factor of the glass, i angle of incidence of solar
ray. The angular height of the sun can be calculated with
the equation (4):
(4)
arcsin sin L sin

cos L cos cos h
where: L geographical latitude, declination, h hour

angle. The hour angle can be calculated with equation (5):
(5)
h 180 l H 0 H H 15
where: l geographical longitude, l0 time zone, H time

of the day, H summer / winter time (-1 / 0). The
temperature of the cell can be calculated with the following
expression [8]:
(6)
Tc Tc,NOCT Tamb,NOCT
Gc
Tamb
GNOCT
where: Tamb,NOCT temperature of the ambient by NOCT (25

C), GNOCT solar irradiance of the ambient by NOCT (800
2
W/m ).
Calculation of the energy yield

Once the power of a PV module is determined, the
power of the whole system can be calculated as well. The
power on the AC side can be calculated by using the
equation (7).
PAC Pm nm 1 con 1 pow 1 arr

(7)
1 ohmDC inv 1 ohmAC
Table 3. Meteorological and geographical data on August 18 2011

at 10:45
Parameter
Symbol
Value
L
Geographical longitude
16,176
H0
+1
Time zone
H
-1
Summer/winter time (-1/0)
L
46,633
Geographical latitude
2
Gg
752 W/m
Global irradiance
2
Gd
165 W/m
Diffuse irradiance
Tm
48,9 C
Temperature of module
Tamb
22,3C
Temperature of ambient
Table 4 presents measured and calculated results for each

inverter and the sum of all inverters in the last row. In the
last column, the relative differences between measured and
calculated results are presented. These values are between
-4,67% and +6,85%. The relative difference between
measured and calculated results for all inverters is -0.79%.
The reason why the difference among the results occurs
lies within the losses, which are different for different
systems. The losses, which are taken into account in
calculations, are determined on the basis of the usual
recommendations given in [9]. These losses are presented
in table 5.
Table 4. Comparison of measured and calculated power
nm
[]
[]
Pme [W]
Pca [W]
252
8
14
12.003,0
12.525,6
234
8
14
12.205,0
11.632,6
234
8
14
11.631,0
11.632,6
234
8
14
12.135,0
11.632,6
234
8
14
11.649,0
11.632,6
234
8
14
12.105,0
11.632,6
234
8
14
11.634,0
11.632,6
234
8
14
11.496,0
11.632,6
225
8
-166
10.513,0
10.481,8
225
8
-166
10.679,0
10.481,8
225
8
-166
10.795,0
10.481,8
225
8
-166
10.904,0
10.481,8
251
8
-166
11.633,0
11.693,1
251
8
-166
11.789,0
11.693,1
251
8
-166
10.943,0
11.693,1
226
9
14
11.562,0
11.258,4
3769
x
X
183.676,0
182.218,7
[%]
4,35
-4,67
0,01
-4,14
-0,14
-3,90
-0,01
1,19
-0,30
-1,85
-2,90
-3,87
0,52
-0,81
6,85
-2,63
-0,79
Figure 6 shows the division of the power for the first

inverter.
where: nm number of modules, con losses due to

contamination, pow losses due to mismatch of the powers,
arr losses due to mismatch of the characteristics, ohmDC
ohmic losses in wires, inv efficiency of the inverter, ohmAC
ohmic losses in wires. The energy yield is calculated as
integral of the produced power on the AC side, as it is given
by the equation (8).
(8)
W AC PAC dt PAC t
Results
The power of the PV power plant with 3769 modules of
the manufacturer First Solar, type FS-277 and 16 inverters
of manufacture SMA type STP1700TL is measured. The
results of the measured power are obtained by the
communication unit Sunny WebBox produced by the SMA.
The meteorological data are measured by using sensor unit
Sunny SensorBox produced by the SMA. The
meteorological and the geographical data are presented in
the table 3.
86
Fig.6. Diagram of the power calculated for the system connected to

the first inverter
Table 5. Losses taken into account by calculations
con
pow
arr
ohmDC
inv
1%
2,5%
1,5%
1%
97,8%
The analysis of the meteorological data is required in

order to calculate the energy yield. In Fig. 7, 8 and 9 are
presented
meteorological
data
obtained
from
meteorological data station Murska Sobota (source: ARSO
Slovenian Environment Agency) and they refer for the last
10 years period of time. All the data are collected in periods
of 30 minutes.
Global irradiance [W/m2]
1200
1000
800
400
200
2002
2004
2006
Year
2008
2010
2008
2010
Diffuse irradiance [W/m2]
Fig.7. Global irradiance on horizontal plane
800
600
400
200
0
Table 6. Meteorological data

Annual
global
irradiation
2
[kWh/m ]
Mean value
1.274,2
The worst
1.194,9
year (2004)
Sum of the
1.078,0
worst months
The best year
1.371,9
(2003)
Sum of the
1.477,2
best months
2002
2004
2006
Year
20
0
-20
2004
2006
Year
2008
10,49
579,5
11,15
523,1
7,69
637,9
9,36
701,4
13,14
The best
year
(2003)
523,4
Sum of
the best
months
562,4
REFERENCES
40
2002
Annual average
ambient
temperature [C]
Conclusion
This paper presents a methodology for the
determination of energy production of the CdTe photovoltaic
system. The energy yield is directly calculated from the
meteorological and geographical data with known PV
module performance and losses of the system.
The exact value of the future annual energy yield cannot
be determined, because of the two main factors. Firstly, no
equation, which can reliably describe the future weather,
can be obtained. It can only be calculated on the basis of a
long-term averages, minimums and maximums. Secondly,
some losses cannot be accurately calculated and need to
be chosen on the basis of the experiences and
recommendations. For more accurate calculation of the
energy yield, the PV module characteristics of the particular
module have to be known.
Fig.8. Diffuse irradiance on horizontal plane
Ambient temperature [C]
Annual
diffuse
irradiation
2
[kWh/m ]
605,3
Table 7. Produced energy in MWh

Mean
The worst
Sum of
value
year (2004)
the worst
months
491,8
464,6
422,4
600
annual energy yield are by annually conditions

491,8(10,06) MWh, or in the worst/best case
491,8(10,14) MWh by monthly conditions.
2010
Fig.9. Ambient temperature
On the basis of these data, some statistics are made.

The mean value, minimum annual value, maximum value,
sum of the worst months and sum of the best months of
annual global irradiation on horizontal plane, annual diffuse
irradiation on horizontal plane and annual average ambient
temperature can be obtained. The results of the previous
calculations are presented in table 6. The energy yield of
the PV power plant with nominal power of 442,8 kW located
nearby the meteorological data station Murska Sobota is
calculated for five different conditions. The data of energy
yields are presented in table 7. On the basis of the
meteorological data from the last 10 years, the value of the
[1] King D.L., Boyson W.E., Kratochvil J.A., Photovoltaic array

performance model, 2004
[2] Huld T., Gottschalg R., Beyer H.G., Topi M., Mapping the
performance of PV modules, effects of module type and data
averaging, Solar Energy, 84 (2010), 324-338
[3] Lenardi D., Fotonapetostni sistemi (Photovoltaic systems),
instructions, 2009
[4] Seme S., tumberger G., A novel prediction algorithm for solar
angles using solar radiation and differential evolution for dualaxis sun tracking purposes, Solar energy, 85 (2011), 27572770
[5] Seme S., tumberger G., Vori J., Maximum efficiency
trajectories of a two-axis sun tracking system determined
considering tracking system consumption, IEEE Trans. Power
Electron., 26 (2011), 1280-1290
[6] Rummich E., Nichtkoventionelle Energieumwandlung, TU Wien
[7] Seme S., tumberger G., Vori J., The optimal tracking
strategies for two-axis PV system. Prz. Elektrotech., 87 (2011),
Iss. 3, 170-174
[8] Huld T., uri M., Dunlop E.D., Geographical Veriation of the
Conversion Efficiency of Crystalline Silicon Photovoltaic
Modules in Europe, Prog. Photovolt: Res. Appl., 16 (2008),
595-607
[9] PVsyst V5.1 Study of Photovoltaic system, Users manual,
2011
Authors: assist. Jan lamberger B. Sc. E. E., University of
Maribor, Faculty of Energy Technology, Hoevarjev trg 1, 8270
Krko, E-mail: jan.slamberger@uni-mb.si; asst. prof. Peter Virti,
Ph.D., University of Maribor, Faculty of Energy Technology,
Hoevarjev trg 1, 8270 Krko, E-mail: peter.virtic@uni-mb.si.
87

Determining Energy Production of Cdte Photovoltaic System: Abstract

Uploaded by

Copyright:

Available Formats

Determining Energy Production of Cdte Photovoltaic System: Abstract

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Determining Energy Production of Cdte Photovoltaic System: Abstract

Uploaded by

Copyright:

Available Formats

Jan LAMBERGER1, Peter VIRTI1

University of Maribor, Faculty of Energy Technology (1)

Determining energy production of CdTe photovoltaic system

Keywords: photovoltaic module, energy production, annual energy yield, Cadmium-Telluride.

Energy yield of PV system is, beside the meteorological

PRZEGLD ELEKTROTECHNICZNY, ISSN 0033-2097, R. 89 NR 2b/2013

Voltage and power in

Power in the maximum-power

Fig.1. The current in the maximum-power point

Fig.2. The voltage and the power in the maximum-power point

Table 2. The coefficients of the equation of the PV module

Figures 4 and 5 show the comparison between the results

Fig.4. The power in the maximum-power point at the real conditions

where: A surface area of the PV module. In comparison to

Fig.3. The temperature of the ambient and the PV module

The equation (1) has been adjusted according to the

Gc irradiance on the cell, Tc cell temperature, Ns

where: PSTC nominal power by STC, GSTC irradiance by

Relative efficiency rel [%]

Current in the maximum-power

Solar manufacturer was tested under real conditions by

Fig.5. Relative efficiency at the real conditions

PRZEGLD ELEKTROTECHNICZNY, ISSN 0033-2097, R. 89 NR 2b/2013

where: Gb beam irradiance, Gd diffusive irradiance, Gg

arcsin sin L sin

where: L geographical latitude, declination, h hour

where: l geographical longitude, l0 time zone, H time

where: Tamb,NOCT temperature of the ambient by NOCT (25

Calculation of the energy yield

PAC Pm nm 1 con 1 pow 1 arr

1 ohmDC inv 1 ohmAC

Table 3. Meteorological and geographical data on August 18 2011

Table 4 presents measured and calculated results for each

Figure 6 shows the division of the power for the first

where: nm number of modules, con losses due to

Fig.6. Diagram of the power calculated for the system connected to

PRZEGLD ELEKTROTECHNICZNY, ISSN 0033-2097, R. 89 NR 2b/2013

Table 5. Losses taken into account by calculations

The analysis of the meteorological data is required in

Global irradiance [W/m2]

Diffuse irradiance [W/m2]

Fig.7. Global irradiance on horizontal plane

Table 6. Meteorological data

Fig.8. Diffuse irradiance on horizontal plane

Ambient temperature [C]

Table 7. Produced energy in MWh

annual energy yield are by annually conditions

Fig.9. Ambient temperature

On the basis of these data, some statistics are made.

[1] King D.L., Boyson W.E., Kratochvil J.A., Photovoltaic array

PRZEGLD ELEKTROTECHNICZNY, ISSN 0033-2097, R. 89 NR 2b/2013

You might also like