S2255053 Function Moveable Contact

Voltage Regulators
Service Information
QD5 Main Movable Contact Replacement Kit Number

5740785B33
Contents
General 1
Parts Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Tools Required 1
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Information 2
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . 3
GENERAL
The purpose of this replacement kit is to provide the parts
and installation instructions for replacing the main movable
contacts on a QD5 Quick Drive Tap Changer.
PARTS SUPPLIED
Item
Part Number
Description
5740785B33
Main Movable Contact

Replacement Kit
Qty
1
Tools Required
Description
Qty
3/8 inch drive ratchet wrench
3/8 inch drive - 3/4 inch (19 mm) deep well socket
3/8 inch drive - 3/8 inch (10 mm) socket
3/8 inch drive - 7/16 inch (11 mm) deep well socket
3/8 inch drive - 9/16 inch (14 mm) socket
3/4 inch (19 mm) open end wrench
5/8 inch (16 mm) open end wrench
3/8 inch drive 0-300 lbs-in torque wrench
Small flat bladed screwdrivers
5/32 inch (4 mm) hex wrench
Pliers
S225-50-53
Read This Manual First
Read and understand the contents of this manual and

follow all locally approved procedures and safety practices
before installing or operating this equipment.
Additional Information
These instructions cannot cover all details or variations
in the equipment, procedures, or process described nor
provide directions for meeting every possible contingency
during installation, operation, or maintenance. For
additional information, contact your representative.
Acceptance and Initial Inspection

Each kit is in good condition when accepted by the
carrier for shipment. Upon receipt, inspect the shipping
container for signs of damage. Unpack the kit and inspect
it thoroughly for damage incurred during shipment. If
damaged is discovered, file a claim with the carrier
immediately.
Handling and Storage

Be careful during handling and storage of the kit to
minimize the possibility of damage. If the kit is to be stored
for any length of time prior to installation, provide a clean,
dry storage area.
Standards
ISO 9001:2000 Certified Quality Management System
Product Information
Introduction
The QD5 Main Movable Contact Replacement Kit and
installation instructions from Cooper Power Systems gives
customers the ability and guidance to replace the QD5
Main Movable Contact during maintenance cycles when
contact erosion has occurred to the point of needing
replacement.
July 2009 New Issue
QD5 Main Movable Contact Replacement Procedure Kit 5740785B33
SAFETY
FOR LIFE
SAFETY FOR LIFE
SAFETY
FOR LIFE
Cooper Power Systems products meet or exceed all applicable industry standards relating to product safety. We actively
promote safe practices in the use and maintenance of our products through our service literature, instructional training
programs, and the continuous efforts of all Cooper Power Systems employees involved in product design, manufacture,
marketing and service.
We strongly urge that you always follow all locally approved safety procedures and safety instructions when working around
high-voltage lines and equipment and support our Safety For Life mission.
SAFETY Information
The instructions in this manual are not intended as a
subs titute for proper training or adequate experience
in the safe operation of the equipment described.
Only competent technicians, who are familiar with this
equipment should install, operate and service it.
A competent technician has these qualifications:
n Is thoroughly familiar with these instructions.
n Is trained in industry-accepted high- and low-voltage
safe operating practices and procedures.
n Is trained and authorized to energize, de-energize, clear,
and ground power distribution equipment.
n Is trained in the care and use of protective equipment
such as flash clothing, safety glasses, face shield, hard
hat, rubber gloves, hotstick, etc.
Following is important safety information. For safe
installation and operation of this equipment, be sure to
read and understand all cautions and warnings.
Safety Instructions
Following are general caution and warning statements that
apply to this equipment. Additional statements, related to
specific tasks and procedures, are located throughout the
manual.
DANGER:
WARNING:
Hazardous voltage. Contact with high voltage will

cause death or severe personal injury. Follow all
locally approved safety procedures when working
around high- and low-voltage lines and equipment.
Before installing, operating, maintaining, or testing

this equipment, carefully read and understand
the contents of this manual. Improper operation,
handling or maintenance can result in death, severe
personal injury, and equipment damage.
Hazard Statement Definitions

This manual may contain four types of hazard
statements:
DANGER:
Indicates a hazardous situation which, if not

avoided, will result in death or serious injury.
WARNING:

avoided, could result In death or serious injury.
CAUTION:

avoided, could result in minor or moderate injury.
Caution: Indicates a hazardous situation which,
if not avoided, could result in equipment damage
only.
2
2
WARNING:
This equipment is not intended to protect human

life. Follow all locally approved procedures and
safety practices when installing or operating this
equipment. Failure to comply may result in death,
severe personal injury and equipment damage.
WARNING:
Power distribution and transmission equipment

must be properly selected for the intended
application. It must be installed and serviced
by competent personnel who have been trained
and understand proper safety procedures. These
instructions are written for such personnel and
are not a substitute for adequate training and
experience in safety procedures. Failure to properly
select, install or maintain power distribution and
transmission equipment can result in death, severe
personal injury, and equipment damage.
S225-50-53
SAFETY
FOR LIFE
Installation Procedure
1. The QD5 should be secured to a bench before starting
the replacement procedure if the tap changer has been
removed from the unit.
2. The QD5 should be in the neutral position before
starting the replacement procedure. Refer to Figure
1. If the QD5 is not in the neutral position, turn the
shaft on the back of the motor shaft using a 3/8 inch
(10 mm) socket on a ratchet until the QD5 is in the
neutral position.
4. Remove the two bolts that mount the actuator finger

with a 7/16 inch (11 mm) socket wrench. Remove the
actuator finger. Refer to Figure 3.
Remove
These Two
Bolts
Actuator
Finger
Figure 3.
Actuator Finger.
5. Remove the nut on the end of the main shaft using

a 3/4 inch (19 mm) socket wrench. Use a 5/8 inch
(16 mm) open end wrench positioned on the flats of
the main shaft to hold the shaft in place during this
procedure. Refer to Figures 4 and 5.
Contacts in
the Neutral
Position
Figure 1.
Neutral Position.
Flats on the
Main Shaft
3. Remove the first stationary contact on the raise side of

the neutral stationary contact from the molded panel
using a 9/16 inch (14 mm) deep well socket wrench.
Refer to Figure 2.
Figure 4.
Main Shaft.
Molded
Panel
Neutral
Stationary
Contact
Nut on the end of

the Main Shaft
First Raise
Stationary
Contact
Removed
Main Shaft
Figure 2.
Stationary Contact.
Figure 5.
Fastening Nut for Main Shaft.
3
6. Slide and position the main shaft so that the retaining

ring on the main shaft is centered between the
movable contact panel and the washer/Geneva gear
hub. Refer to Figure 6.
Retaining Ring
Movable Contact
Panel
Washer
8. Push the threaded end of the main shaft through the

steel panel toward the molded panel. Support the
Geneva gear with one hand and pull the main shaft out
from the back of the molded panel until the main shaft
is out of the Geneva gear hub making sure the washer
remains on the shaft. Remove the Geneva gear and
slide the washer off the shaft. Refer to Figure 8.
Geneva Gear
Hub
Figure 6.
Shaft Positioning.
7. Use a pair of pliers to remove the retaining ring. Slide

the washer up against the movable contact panel.
Refer to Figure 7.
Figure 8.
Removal of Shaft.
9. Pull the main shaft completely out of the back of the

molded panel. Rotate the movable contacts off of the
neutral stationary contact into the space provided by
the removed stationary contact. Pull the contact rings
out of the button contacts and remove the movable
contact panel assembly. Refer to Figure 9.
Washer
Button Contacts
Figure 7.
Washer.
Figure 9.
Removal of Main Contacts.
S225-50-53
SAFETY
FOR LIFE
10. Remove the three button head screws, nuts and

washers that secure each contact to the movable
contact panel using a 5/32 inch (4 mm) hex wrench
and a 7/16 inch (11 mm) deep well socket wrench.
Refer to Figures 10 and 11.
Note: The center button head screw on each movable
contact assembly has a flat washer and a Belleville
washer under the nut.
Movable Contact
Assemblies
Button Head
Screw
11. The two replacement movable contact assemblies

are identical; therefore, they can be installed in either
position on the movable contact panel. Position one of
the replacement movable contact assemblies between
the contact ring and the movable contact panel and
align the holes. Insert the three button head screws
from the contact ring side of the assembly so the
screw heads secure the contact ring in place. On the
side opposite the contact ring, place a flat washer
on all three screws. Place a Belleville washer on the
center screw and thread a Nylok nut onto all three
screws. Tighten the Nylok nuts to 65 to 75 in-lbs
using a 7/16 inch (11 mm) deep well socket wrench
while holding the screw in place with a 5/32 inch
(4 mm) hex wrench. Refer to Figures 10 and 11.
Repeat this procedure for the other movable contact
assembly.
12. Position and center the movable contact panel
assembly in the molded panel cavity with the contact
rings facing the molded panel. Locate the movable
contacts in the area of the removed stationary contact.
Rotate the movable contact panel and slide the
movable contacts onto the neutral stationary contact.
Align the contact rings with the button contacts. Refer
to Figure 12.
Figure 10.
Movable Contact Removal from Insulating Arm and Rings.
Movable Contacts
on Stationary Neutral
Contact
Nut and Flat

Washer
Center Screw with

Nut, Flat Washer
and Belleville
Washer
Contact Ring Aligned

with Button Contact
Figure 12.
Installation of Movable Contacts and of Rings.
Figure 11.
Removal of Contacts.
13. From the back of the molded panel, insert a small

blade screwdriver between the button contact spring
and the button contact shunt on each side of the
contact. Refer to Figure 13.

Squeeze the handles of the small screwdrivers
together to spread apart the button contacts. Push
the aligned ring contact in between the button contact
so the buttons are fully engaged with the contact ring.
Refer to Figures 14 and 15. Repeat this process on
the other button contact assembly.
Small Blade
Screwdriver
Button Contact
Shunt
Figure 15.
Ring and P Contacts.
Button Contact
Spring
14. Insert the threaded end of the main shaft through the
back of the molded panel, then through the movable
contact panel until the threads of the shaft are just
protruding out of the movable contact panel. Slide the
washer onto the main shaft and position it against the
movable contact panel. Refer to Figure 16.
Figure 13.
Installing Rings into P1 and P2.
Figure 16.
Installing Main Shaft.
Figure 14.
Installing Ring into P2 Contact.
S225-50-53
SAFETY
FOR LIFE
15. Position the Geneva gear so the pin on the back of

the Geneva gear lines up with the slot in the Geneva
section and the half-moon shaped groove on the
outer edge of the Geneva gear lines up with the halfmoon shaped drive on the sprocket. Push the main
shaft into the center hole of the Geneva gear until the
end of the shaft hits the metal panel. Install the e-clip
into the e-clip groove on the main shaft. Align the main
shaft with the 1/2 inch through hole in the steel panel.
Push the main shaft into the steel panel ensuring that
the neutral switch activator arm is depressed by the
Geneva gear activator and not pinched under the
Geneva gear activator. Secure the steel shaft to the
steel panel using the kit supplied 1/2 inch -13 lock nut.
Use a 5/8 inch (16 mm) open end wrench to hold the
steel shaft while securing the nut on the threaded end
of the shaft with a 3/4 inch (19 mm) socket wrench.
Torque the nut to 180 to 400 in-lbs. Refer to Figures
17 and 18. Ensure the Geneva pin is engaged with the
Geneva section by checking the viewing hole in the
steel panel. Refer to Figure 19.
Viewing Hole in
the Steel Panel
Geneva Section
Geneva Pin
Main Shaft
Figure 19.
Viewing Hole for Geneva and Reversing Actuator.
16. Use the nuts that were removed in Step 4 to reinstall

the 2-raise stationary contact. Torque the nuts for the
stationary contact to 110 to 120 in-lbs.
Half-moon Shaped Slots

on the Outer Edge of the
Geneva Gear
Geneva Section
Figure 17.
Aligning Geneva Gear.
E-Clip
Washer
Figure 18.
Locating of E-Clip.
Reversing Neutral
Stationary Contact
SAFETY
FOR LIFE
2009 Cooper Industries. All Rights Reserved.

Cooper Power Systems is a valuable trademark of Cooper Industries in the U.S. and
other countries. You are not permitted to use the Cooper Trademarks without the prior
written permission of Cooper Industries.
Nylok is a registered trademark of the Nylok Corporation.
S2255053 Rev.0
2300 Badger Drive

Waukesha, WI 53188 USA
www.cooperpower.com

S2255053 Function Moveable Contact

Uploaded by

Copyright:

Available Formats

S2255053 Function Moveable Contact

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

S2255053 Function Moveable Contact

Uploaded by

Copyright:

Available Formats

Voltage Regulators

QD5 Main Movable Contact Replacement Kit Number

Main Movable Contact

3/8 inch drive ratchet wrench

3/8 inch drive - 3/8 inch (10 mm) socket

3/8 inch drive - 9/16 inch (14 mm) socket

3/4 inch (19 mm) open end wrench

5/8 inch (16 mm) open end wrench

3/8 inch drive 0-300 lbs-in torque wrench

Small flat bladed screwdrivers

5/32 inch (4 mm) hex wrench

Read This Manual First

Read and understand the contents of this manual and

Acceptance and Initial Inspection

Handling and Storage

July 2009 New Issue

QD5 Main Movable Contact Replacement Procedure Kit 5740785B33

SAFETY FOR LIFE

Hazardous voltage. Contact with high voltage will

Before installing, operating, maintaining, or testing

Hazard Statement Definitions

Indicates a hazardous situation which, if not

Indicates a hazardous situation which, if not

Indicates a hazardous situation which, if not

This equipment is not intended to protect human

Power distribution and transmission equipment

4. Remove the two bolts that mount the actuator finger

5. Remove the nut on the end of the main shaft using

3. Remove the first stationary contact on the raise side of

Nut on the end of

QD5 Main Movable Contact Replacement Procedure Kit 5740785B33

6. Slide and position the main shaft so that the retaining

8. Push the threaded end of the main shaft through the

7. Use a pair of pliers to remove the retaining ring. Slide

9. Pull the main shaft completely out of the back of the

10. Remove the three button head screws, nuts and

11. The two replacement movable contact assemblies

Nut and Flat

Center Screw with

Contact Ring Aligned

QD5 Main Movable Contact Replacement Procedure Kit 5740785B33

13. From the back of the molded panel, insert a small

15. Position the Geneva gear so the pin on the back of

16. Use the nuts that were removed in Step 4 to reinstall

Half-moon Shaped Slots

QD5 Main Movable Contact Replacement Procedure Kit 5740785B33

2009 Cooper Industries. All Rights Reserved.

2300 Badger Drive

You might also like