A) Positive Allowance + Negative Allowance
A) Positive Allowance + Negative Allowance
a)
b)
c)
d)
2.
a)
b)
c)
d)
12. Load is applied per square inch a material can withstand without
resulting in a permanent elongation more than 0.0001 per inch of
gage length after complete release of stress is known as
a) elastic limit
b) proof stress
c) proportional limit
d) yield strength
3.
a)
b)
c)
d)
13.
a)
b)
c)
d)
4.
8.
a)
b)
c)
d)
proof stress
proper final limit
modulus of elasticity
elastic limit
Pin is used
in non-load carrying part
in shear application
is not reused
both b & c
16.
a)
b)
c)
17.
a)
b)
c)
d)
Tolerance means
positive allowance + negative allowance
positive allowance
in orthography not more than 3 view are possible
both a & c
18.
a)
b)
c)
d)
19.
a)
b)
c)
20.
a)
b)
c)
d)
21.
a)
b)
c)
d)
Lockbolt is combination of
rivet +
lock nutt
bolt +
rivet +bolt
24.
a)
b)
c)
d)
25.
a)
b)
c)
d)
26.
a)
b)
c)
28.
a)
b)
c)
d)
Purpose of tempering is
to reduce strength
to reduce ductility and increase brittleness
to reduce hardness and reduce brittleness
to increase hardness and reduce brittleness
29.
a)
b)
c)
d)
30.
a)
b)
c)
d)
Spherodising is done
prolonged heating just above critical temp
prolonged cooling just below critical temp
prolonged heating just below critical temp
smaller time
31.
a)
b)
c)
d)
32.
a)
b)
c)
d)
Paint is combination of
Enamel = pigment
Varnish + Enamel
Pigment +Vehicle
Pigment + Varnish
33.
a)
b)
c)
d)
Working drawing-9A 35
given rough idea about the component, system drawn
it includes assembly drawing
as in b + includes installation drawing
all of the above
39.
a)
b)
c)
d)
40.
a)
b)
c)
d)
41.
a)
b)
c)
Brinell no indicated by
weight applied in lbs divided inch sq. impression
weight applied in kgs and divided by mm sq. impression
weight applied in kgs and divided m2 impression
weight applied in lbs and divided by clia-at impression
54.
a)
b)
c)
d)
55.
a)
b)
c)
d)
56.
a)
b)
c)
d)
57.
a)
b)
c)
d)
47.
a)
b)
c)
d)
58.
a)
b)
c)
d)
SCR is
two junction diode
three junction diode
two junctions are forward biased, two ae reverse biased
all of the above
48.
a)
b)
c)
d)
59.
a)
b)
c)
d)
49.
a)
b)
c)
d)
50. Before jacking an a/c few steps are taken regarding this mark
the correct statement -9A
a) for heavy a/c and smaller a/c same procedure & precaution should
be observed
b) jack must be of capacity 20% more than the weight to be lifted
c) for proper capacity, condition of locking pin or arm , proper
functioning
d) all of the above
51.
a)
b)
c)
-9A 536
Alodine is applied by
cladding
dipping
priming
as per manufactures diagonosis
65.
a)
b)
c)
d)
66.
a)
b)
c)
d)
67.
a)
b)
c)
d)
72.
a)
b)
c)
d)
76. During refueling chock is set at little distance from wheel because
-CAP
a) to absorb shock when tire is set
b) electro static generated
c) chock may be trapped into the fire
d) chock can be applied if a/c moves during refueling
77. Close tolerance bolts are -9A 123
a) pushed into the hole by hand pressure
b) it is machined accurately than general purpose bolt and installed
by hammering
c) used where light drive fit is required
d) all of the above
78.
a)
b)
c)
d)
79.
a)
b)
c)
d)
84.
a)
b)
c)
85. MTCS:
a) Bolt has right hand threads except in special cases
86.
a)
b)
c)
87.
a)
b)
c)
88.
a)
b)
c)
89.
a)
b)
c)
d)
92.
a)
b)
c)
93.
a)
b)
c)
94.
a)
b)
c)
d)