Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
166 views

(Journal) Design and Implementation of Zigbee Transmitter On Fpga Using VHDL

fpga vhdl

Uploaded by

FranxCuckoo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
166 views

(Journal) Design and Implementation of Zigbee Transmitter On Fpga Using VHDL

fpga vhdl

Uploaded by

FranxCuckoo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

DESIGN AND IMPLEMENTATION OF

ZIGBEE TRANSMITTER ON FPGA USING VHDL


1

PUNIT RAMACHANDRA RAMAJI, 2MANJUNATH G ASUTI


1

M-Tech VLSI Design and Embedded Systems, RITM Bangalore


2
Assistant Professor ECE Dept, RITM Bangalore

Abstract- This paper explores the implementation of a digital transmitter for 2.4 GHz Zigbee IEEE 802.15.4 applications on
a field programmable gate array (FPGA) for an Acknowledgement frame. Zigbee technology was developed for a
Wireless Personal Area Networks (WPAN), aimed at control and military applications with low data rate and low power
consumption. Zigbee is a standard defines the set of communication protocols for low data-rate, short-range wireless
networking. Zigbee based wireless devices operate in 868 MHz, 915 MHz, and 2.4 GHz frequency bands. Digital Zigbee
Transmitter comprises of Cyclic Redundancy Check, Bit-to-Symbol block, Symbol-to-chip block, Offset QPSK Modulator.
The work here is to show how we can design Zigbee transmitter with its specifications by using VHDL code through Xilinx
ISE version 12 was developed to design these blocks.

I. INTRODUCTION
Zigbee is a low data rate, low power, and low cost
wireless networking protocol based on the IEEE
802.15.4, which is a set of new communication
protocols for wireless transmission. Zigbee protocol
defines the media access control (MAC) and physical
(PHY) layers for low rate WPANs. It supports the
frequency bands 868 MHz for European countries,
915 MHz for the United States, and 2.4 GHz for
worldwide.

Figure1. The acknowledgment frame

The acknowledge frame used contains 11 octets (i.e.


88 bits) of physical protocol data unit (PPDU). The
binary data from the PPDU packet are inserted into
the cyclic redundancy check block to detect errors
during transmission. The Cyclic Redundancy Check is
the most powerful of the redundancy checking
techniques, the CRC is based on binary division. In
CRC a sequence of redundant bits, called the CRC or
the CRC remainder is appended to the end of a data
stream. The resulting data becomes exactly divisible
by a second, predetermined binary number. At its
destination, the incoming data is divided by the same
number.

Main network topologies used in ZigBee wireless


networking are star and peer-to-peer networks. In the
star topology, every device in the network can
communicate only with the personal area network
coordinator. A Full Function Device takes up a role as
PAN coordinator; the other nodes can be Reduced
Function Device or Function Device. In the peer-topeer topology, each device can communicate directly
with any other device if the devices are close enough
together to establish a successful communication link.
Any Function Device in this topology can play the
role of the personal area network coordinator.

The diagram below will show you the Sequence of


Events that takes place when using CRC. CRCs can
detect all one bits and two bits errors as well as all odd
number of bits in error. Since CRC is a technique for
detecting errors, but not for making corrections when
errors are detected, the whole packet data will be
retransmitted if error occurs. For Zigbee Standard,
CRC involves a division of the transmitted packet data
by a constant called the generator polynomial. The
CRC block contains the SHR, PHR and PHY payload.
In the PHY payload, the FCS mechanism employs a
16-bit CRC in order to detect errors. The FCS is
calculated over the MHR and MFR payload parts of
the frame using the algorithm Every four bits of
PPDU octet are mapped onto one data symbol, which
will take place in bit-to-symbol block. The symbols

Zigbee digital transmitter in 2.4GHz band is designed


using VHDL for acknowledgement frame. MAC
frame structures consist of beacon, data,
acknowledgment, and MAC command frames. The
MAC layer defines two types of nodes: Reduced
Function Devices and Full Function Devices .The
beacon frame is used by a coordinator to transmit
beacons.
The function of beacons is to synchronize the clock of
all the devices within the same network. The data
frame is used to transmit data. Meanwhile, the
acknowledgement frame is used to confirm successful
frame reception. The Zigbee digital transmitter is
designed for acknowledgment frame which is shown
in Figure 1 based on IEEE 802.15.4standard.

Proceedings of 10th IRF International Conference, 01st June-2014, Pune, India, ISBN: 978-93-84209-23-0
148

Design and Implementation of Zigbee Transmitter on FPGA Using VHDL

will be spread into 32-chip PN sequence by utilizing


Direct Sequence Spread Spectrum method in Symbolto-chip block. Then, the chips will be modulated using
OQPSK technique.

frames which is originated from MAC sub-layer is


inserted into the CRC block. Then, every 4 bits are
mapped into one data symbol in the bit-to-symbol
block. The symbol-to-chip block performs the DSSS
where each symbol is mapped into a 32-chip PN
sequence as shown in Table 1. After that, these chips
are processed by OQPSK (Offset Quadrature Phase
Shift Keyed) modulator.

Fig 3: Transmitter Architecture

II. DESIGN METHODOLOGY


The behaviour of the Zigbee digital transmitter can be
modelled using VHDL through Xilinx ISE. The
VHDL module for each transmitter can be combined,
then synthesized, simulated, and implemented on
Spartan3E FPGA.

OQPSK (offset QPSK) is a special version of QPSK


in which the transmitted signal has no amplitude
modulation. This disadvantage of a amplitude
modulation are a result of 180 shifting in the phase.
In OQPSK the incoming signal is divided in the
modulator into two portions I and Q which are then
transmitted shifted by a half symbol duration. The
phase plane of a OQPSK is shown in Figure 2. There
is no phase shift through the zero crossing which
means there are no phase shifts by 180 as in a
standard QPSK.

The input data comprise 22 symbols. Each data


symbol from the bit-to-symbol block is append onto
a 32-chip PN sequence using the DSSS method. The
output data are 704 chips in total with the frequency of
2 MHz . The numbers of chips produced are based
on[88 bits/4] symbols x 32 = 704 chips Based on this
equation, each even chip of output data is registered as
C0, C2 .. C704, and each odd chip is registered as
C1, C3 C703, which is totally 352 chips each for Iphase and Q-phase.
III. RESULTS AND DISCUSSION
Simulation and implementation were performed for
the digital Transmitter. The output waveforms were
compared to verify their functionality. The simulation
waveform shown in below Figure.
Waveform for Transmitter Data Bits

Figure 3: Cyclic Redundancy Check

Table 1: Symbol to chip mapping using DSSS


The proposed digital transceiver for Zigbee
applications is shown in Fig 3. The acknowledgment

Waveform for BIT-TO-SYMBOL Simulation

Proceedings of 10th IRF International Conference, 01st June-2014, Pune, India, ISBN: 978-93-84209-23-0
149

Design and Implementation of Zigbee Transmitter on FPGA Using VHDL

CONCLUSION
This paper shows the VHDL based design of digital
transmitter for 2.4GHz band Zigbee applications. The
behaviour of CRC and Bit-to-symbol were
characterized using VHDL. The functionality of the
proposed transmitter matches its theoretical
expectation. With VHDL, the transmitter design area
could be reduced to a smaller scale.
REFERENCES
[1]

Zigbee Alliance, available at: www.zigbee.org.

[2]

A. Mohammed Mian and Divyabharathi. R, Design and


Simulation of ZIGBEE Transmitter Using Verilog

[3]

RAFIDAH AHMAD*, OTHMAN SIDEK, SHUKRI


KORAKKOTTIL KUNHI MOHD, IMPLEMENTATION
OF A VERILOG-BASED DIGITAL RECEIVER FOR 2.4
GHz ZIGBEE APPLICATIONS ON FPGA

[4]

Somya Goel1, Dr Ranjit Singh2, FIETE, VHDL Based


Design and Implementation of Zigbee Transreceiver on
FPGA

[5]

Wireless Communications: The Future William Webb


2007 John Wiley & Sons, Ltd. ISBN: 0-470-03312-6

[6]

Rafidah Ahmad, Othman Sidek, Wan Md. Hafizi Wan


Hassin, Shukri Korakkottil Kunhi Mohd, and Abdullah
Sanusi Husain, Verilog-Based Design and Implementation
of Digital Transmitter for Zigbee Applications

[7]

Alberto Camilli, Carlos E. Cugnasca, Antonio M. Saraiva,


Andre R. Hirakawa, Pedro L.P. Correa, From wireless
sensors to field mapping: Anatomy of an application for
precision agriculture.

Waveform for SYMBOL-TO-CHIP Simulation

Proceedings of 10th IRF International Conference, 01st June-2014, Pune, India, ISBN: 978-93-84209-23-0
150

You might also like