Ce2404 Pcs Notes

www.Vidyarthiplus.
com
www.Vidyarthiplus.com
PRESTRESSED CONCRETE STRUCTURES
UNIT-I INTRODUCTION THEORY AND BEHAVIOUR

Sem/Year: VII/IV
PART-A
1. What are the advantages of PSC construction
In case of fully prestressed member, which are free from tensile stresses under
working loads, the cross section is more efficiently utilized when compared with a
reinforced concrete section which is cracked under working loads.
The flexural member is stiffer under working loads than a reinforced concrete
member of the same length.
2. Define Pre tensioning and Post tensioning
Pre tensioning: A method of Pre stressing concrete in which the tendons are
tensioned before the concrete is placed. In this method, the prestress is imparted
to concrete by bond between steel and concrete.
Post tensioning: A method of pre stressing concrete by tensioning the tendons
against hardened concrete. In this method, the prestress is imparted to concrete by
bearing.
3. What is the need for the use of high strength concrete and tensile steel in Pre stressed
concrete?
High strength concrete is necessary for prestress concrete as the material offers
highly resistance in tension, shear bond and bearing. In the zone of anchorage the
bearing stresses being hired, high strength concrete is invariably preferred to
minimizing the cost. High strength concrete is less liable to shrinkage cracks and
has lighter modulus of elasticity and smaller ultimate creep strain resulting in a
smaller loss of prestress in steel. The use of high strength concrete results in a
reduction in a cross sectional dimensions of prestress concrete structural element
with a reduced dead weight of the material longer span become technically and
economically practicable.
Tensile strength of high tensile steel is in the range of 1400 to 2000 N/mm2 and
if initially stress upto 1400 N/mm2 their will be still large stress in the high tensile
reinforcement after making deduction for loss of prestress. Therefore high tensile
steel is made for prestress concrete.
4. Define Kern Distance.

Kern is the core area of the section in which if the load applied tension will not
be induced in the section
Kt = Zb/A,
Kb = Zt/A,
If the load applied
at www.Vidyarthiplus.com
Kt compressive stress will be the maximum at the top most
fiber and zero stress will be at the bottom most fiber. If the load applied at Kb
compressive stress will be the maximum at the bottom most fiber and zero stress
will be at the top most fiber.
5. What is Relaxation of steel?
When a high tensile steel wire is stretch and maintained at a constant strain the
initially force in the wire does not remain constant but decrease with time. The
decrease of stress in steel at constant strain is termed relaxation of steel.
6. What is concordant prestressing?
Pre stressing of members in which the cable follow a concordant profile. In case
of statically indeterminate structures. It does not cause any changes in support
reaction.
7. Define bonded and non bonded prestressing concrete.
Bonded prestressing: Concrete in which prestress is imparted to concrete
through bond between the tendons and surrounding concrete. Pre tensioned
members belong to this group.
Non-bonded prestressing: A method of construction in which the tendons are
not bonded to the surrounding concrete. The tendons may be placed in ducts
formed in the concrete members or they may be placed outside the concrete
section.
8. Define Axial prestressing
Members in which the entire cross-section of concrete has a uniform
compressive prestress. In this type of prestressing, the centroid, of the tendons
coincides with that of the concrete section.
9. Define Prestressed concrete.
It is basically concrete in which internal stresses of a suitable magnitude and
distribution are introduced so that the stresses resulting from external loads (or)
counteracted to a desire degree in reinforced concrete member the prestress is
commonly introduced by tensioning the steel reinforcement
10. Define anchorage.
A device generally used to enable the tendon to impart and maintain prestress to
the concrete is called anchorage. e.g. Fressinet, BBRV systems,etc.,
PART-B:
1. a) What are the advantages of Prestressed Concrete
In case of fully prestressed member, which are free from tensile stresses under
working loads.
The cross section is more effectively utilized when compared with a reinforced
concrete section which is cracked under working loads.
Within certain limits,
a permanent dead load may be counteracted by increasing
the eccentricity of the prestressing force in a prestressed structural elements, thus
effecting saving in the use of materials.
Prestressed concrete members possess improved resistance to shearing forces, due
to the effect of compressive prestress, which reduces the principal tensile stress.
The use of high strength concrete and steel in prestressed members results in
lighter and slender members than is possible with reinforced concrete.
It is free from cracks, contributes to the improved durability of the structure under
aggressive environmental conditions.
The economy of prestressed concrete is well established for long span structures.
A prestressed concrete flexural member is stiffer under working loads than a
reinforced concrete member of the same depth.
b) Describe briefly Fressinet system of post tensioning

PRINCIPLES OF POST-TENSIONING:
In post-tensioning, the concrete units are first cast by incorporating ducts
or grooves to house the tendons. When the concrete attains sufficient strength, the hightensile wires are tensioned by means of jack bearing on the end face of the member and
anchorags by wedges or nuts.
FREYSSINET SYSTEM OF POST TENSIONING:
The Freyssinet system of post-tensioning anchorages which was
developed in 1939.
The Freyssinet anchorage system, which is widely used in Europe and
India, consists of a cylinder with a conical interior through which the high-tensile wires
pass and against the walls of which the wires are wedged by a conical plug lined
longitudinally with grooves to house the wires. The main advantages of the Freyssinet
system is that a large number of wires or strands can be simultaneously tensioned using
the double-acting hydraulic jack.
2. a) Discuss about the importance of control of deflections and the factors influencing the
deflection of PSC beams
IMPORTANCE OF CONTROL OF DEFLECTION:
The structural concrete
members should be designed to have adequate stiffness to
limit deflections, which may adversely affect the strength or serviceability oof the
structure at working loads.
Suitable control on deflection is very essential for the following reasons:
Excessive, sagging of principal structural members is not only unsightly,
but at times, also renders the floor unsuitable for the intended use.
Large deflections under dynamic effects and under the influence of
variable loads may cause discomfort to the users.
Excessive deflections are likely to cause damage to finishes, partitions
and associated structures.
FACTORS INFLUENCING DEFLECTIONS:
The deflections of prestressed concrete members are influenced byy the following
salient factors:
Imposed load and self weight

Magnitude of the prestressing force
Cable profile
Second moment of area of cross section
Modulus of elasticity of concrete
Shrinkage, creep and relaxation of steel stress
Span of the member
Fixity conditions
b) Describe the various types of losses in prestress. What steps may be taken to reduce
these losses
LOSS DUE TO ELASTIC DEFORMATION OF CONCRETE:
The loss of prestress due to elastic deformation of concrete depends on the
modular ratio and the average stress in concrete at the level of steel.
If
fc= prestress in concrete at the level of steel.
Es= modulus of elasticity of steel.
Ec= modulus of elasticity of concrete.
e= Es/ Ec = modular ratio.
Strain in concrete at the level of steel = (fc/ Ec)
Stress in steel corresponding to this strain = (fc/ Ec) Es
Loss of stress in steel = e fc
If the initial stress in steel is known, the percentage loss of stress due to the
elastic deformation of concrete can be computed.
LOSS DUE TO SHRINKAGE OF CONCRETE:
The shrinkage of concrete in prestressed members results in a shortening
of tensioned wires and hence contributes to the loss of stress. The
shrinkage of concrete is influenced by the type of cement and aggregates
and the method
of curing used. Use of high-strength concrete with low
water cement ratios result in a reduction in shrinkage and consequent loss
of prestress.
According IS1343 for the loss of prestress due to the shrinkage of
concrete
cs = total residual shrinkage strain having values of 300x106 for pre
tensioning and [200x106/log10(t+2)]
Where, t = age of concrete at transfer in days.
The loss of stress in steel due to the shrinkage of concrete is estimated as,
Loss of stress = cs x Es
LOSS DUE TO CREEP OF CONCRETE:
The sustained prestress in the concrete of a prestressed member results in
creep of concrete which effectively reduces the stress in high-tensile steel.
The loss of stress in steel due to creep of concrete can be estimated if the
magnitude of ultimate creep strain or creep coefficient is known.
ULTIMATE CREEP STRAIN METHOD:
If cc = ultimate creep strain for a sustained unit stress
fc = Compressive stress in concrete at the level of steel.
Es = modulus of elasticity of steel.
Loss of stress in steel due to creep of concrete = cc fc Es
CREEP COEFFICIENT METHOD:
If
= creep coefficient
c = creep strain
e = elastic strain
e = modular ratio
fc = stress in concrete
Ec = modulus of elasticity of concrete.
Creep coefficient() = (c/ e)
Loss of stress in steel = fc e
LOSS DUE TO RELAXATION OF STRESS INN STEEL:
Most of the code provides for the loss of stress due to relaxation of steel as
a percentage of the initial stress in steel. The Indian standard code
recommends a value varying from 0 to 90 N/mm2 for stress in wire
varying from 0.5 fup to 0.8 fup .
LOSS OF STRESS DUE TO FRICTION:
On tensioning the curved tendons, loss of stress occurs in the posttensioned members due to friction between the tendons and the
surrounding concrete ducts. The magnitude of this loss is of the following
types:
(a) Loss of stress due to the curvature effects, which depends upon
the tendon from or alignment which generally follows a curved profile along the
length of the beam.
(b)www.Vidyarthiplus.com
Loss
of stress due to the wobble effect, which depends upon
the local deviation in the alignment of the cable. The wobble or wave effect is the
result of accidental or unavoidable misalignment, since ducts or sheaths cannot be
perfectly located to follow predetermined profile throughout the length of the
beam.
Px = Poe-(+ kx)
LOSS DUE TO ANCHORAGE SLIP:
In most post-tensioned system, when the cable is tensioned and the jack is
released to transfer prestress to concrete, the friction wedges, employed to
grip the wires, slip over a small distance before the wires are firmly
housed between the wedges. The magnitude of slip depends upon the type
of wedge and the stress in the wire.
= (PL/AEs)
Where = slip of anchorage, mm
L = length of the cable,mm
A = cross sectional area of the cable, mm2
P = Prestressed force in the cable.
PRESTRESSED CONCRETE STRUCTURES
UNIT-II DESIGN
Sem/Year: VII/IV
PART-A
1. What is meant by end block in a post tensioned member?
The zone between the end of the beam and the section where only longitudinal
stress exists is generally referred to as the anchorage zone or end block.
2. List any two applications of partial prestressing.
Used in large diameter concrete pipes
Used in railway sleepers
Water tanks
Precast concrete piles to counter tensile stress during transport and erection.
used in bridges construction
3. What is meant by partial prestressing?
The degree of prestress applied to concrete in which tensile stresses to a limited
degree are permitted in concrete under working load. In this case, in addition to
tensioned steel, a considerable proportion of untensioned reinforcement is
generally used to limit the width of cracks developed under service load.
4. Define degree of prestressing
A measure of the magnitude of the prestressing force related to the resultant
stress occurring in the structural member at working load.
5. Define Bursting tension.
The effect of transverse tensile stress is to develop a zone of bursting tension in a
direction perpendicular to the anchorage force resulting in horizontal cracking.
6. Define Proof stress
The tensile stress in steel which produces a residual strain of 0.2 percent of the
original gauge length on unloading.
7. Define cracking load.
The load on the structural element corresponding to the first visible crack.
8. Define Debonding.
Prevention of bond between the steel wire and the surrounding concrete.
9. Write formula for Moment of resistance in BIS code.
Mu = Apb Aps (d-dn)
10. What are the types of flexural failure?
Fracture of steel in tension
Failure of under-reinforced section
Failure of over-reinforced section
Other modes of failure
PART-B
1. a) What is meant by partial prestressing? Discuss the advantages and disadvantages when
partial prestressing is done
PARTIAL PRESTRESSING:
The degree of prestress applied to concrete in which tensile stresses to a
limited degree are permitted in concrete under working load. In this case,
in addition to tensioned steel, a considerable proportion of untensioned
reinforcement is generally used to limit the width of cracks developed
under service load.
ADVANTAGES:
Limited tensile stresses are permitted in concrete under service

loads with controls on the maximum width of cracks and
depending upon the type of prestressing and environmental
condition.
Untensioned reinforcement is required in the cross-section of a
prestresseed member for various reasons, such as to resist the
differential shrinkage, temperature effects and handling stresses.
Hence this reinforcement can cater for the serviceability
requirements, such as control of cracking, and partially for the
ultimate limit state of collapse which can result in considerable
reduction in the costlier high tensile steel.
Saving in the cost of overall structure.
DISADVANTAGES:
The excessive upward deflections, especially in bridge structure

where dead loads from a major portion of the total service loads,
and these deflections may increase with time of creep.
(b) Explain about the types of flexure failure occurs in prestressed concrete section
3.
Discuss about the anchorage zone reinforcement. The end block of a post
tensioned PSC beam 300mm x 300mm is subjected to concentric anchorage force of
800KN by a Freyssinet anchorage of area 10000mm2. Design and detail the anchorage
reinforcement for the block.
ANCHORAGE ZONE REINFORCEMENT:
The main reinforcement in the anchorage zone should be designed to
withstand the bursting tension, which is determined by the transverse stress distribution
on the critical axis, usually coinciding with the line of action of the largest individual
force for plate and embedded ( Freyssinet) type of anchorage the typical arrangement of
reinforcement in end block, mat, helical, loops or links are generally provided in
perpendicular directions. test by Zielinski and Rowe have shown that helical
reinforcement is more efficient than mat reinforcement . in view of the shot available
bond length , loops, hooks , (or) right angle bends are necessary, even with deformed
bars.
6. (a) Explain concept of limit states, partial safety factor.
Partial safety factors, are therefore used for each limit state being reached.
The values of partial safety loads recommended in the British, Indian
and American codes.
IS code:
Load combination
Limit state of collapse
Limit state of serviceability
DL
LL
WL
DL
LL
WL
DL+LL
1.5
1.5
1.0
1.0
DL+WL
1.5
1.5
1.0
1.0
DL+LL+WL
1.2
1.2
1.2
1.0
0.8
0.8
Partial safety factor for materials has a values which depends on the
important of limit states being materials to which is applies difference between
strength of materials when tested and when incorporated in construction during the
service life.
(b) Discuss difference in load deflection of under prestressed, partially prestressed and
fully prestressed.
The load deflection characteristics of a typical prestressed concrete members
and discussed below:
If the beam is sufficient loaded, tensile stresses is develop in the soffit and
when this exceed the tensile strength of concrete, cracks are likely to develop in the
member.
The load deflection curve is approximately linear upto the stage of visible
cracking, but beyond this stage the deflection increase at a faster rate due to the
reduced stiffness of the beam.
In the port- cracking of the beam of beam is parallel to that of reinforced
concrete member.
The deflection of cracked structural member, may be estimated by the unilinear
or bilinear method recommended by the ECC.
In the unilinear method, the deflection will be,
a= L2M/ Ec Ir
where a = Max deflection
L = Effective span
M = Max moment
Ec = Modulus of elasticity of concrete
Ir = IInd commend of area.
In the bilinear method, the moment curvature is approximately by second straight
line.
The instantaneous deflection in the post cracking stage is obtained as the sum of
deflection upto cracking load based on gross section and beyond the cracking load
considering the cracked section.
Hence deflection are estimated by
a= L2 {(Mcr/ EcIc)+((M-Mc)/0.85Ecfck)}
SUDHARSAN ENGINEERING COLLEGE

DEPARTMENT OF CIVIL ENGINEERING
SUBJ. CODDE AND NAME: CE 1402 PRESTRESSED CONCRETE STRUCTURES
FACULTY NAME: S.ARUNKUMAR
CLASS &SEC :IV yr CIVIL
Academic year: 2013-14
Semester :VI
UNIT 3
Part A
1. Sketch the loop reinforcement, hair-pin bars in end blocks.(NOV-DEC 2009)
2. Sketch the correct arrangement of sheet cage in anchorage zone.(NOV-DEC 2009)
3. Define two stage constructions.(NOV-DEC 2012)

One-stage construction: Construct and initialize the object in one stage, all with
the constructor.
Two-stage construction: Construct and initialize the object in two separate stages.
The constructor creates the object and an initialization function initializes it.
4. Write any two general failures of prestressed concrete tanks.(NOV-DEC 2012)
deformation of the pre-cast concrete units during construction
Manufacturing inaccuracies led to out of tolerance units being delivered to the site
under investigation and may have affected the ability to achieve a good seal.
5. Mention the importance of shrinkage in composite construction?(NOV-DEC
2010)
The time dependent behavior of composite prestressed concrete beams
depends upon the presence of differential shrinkage and creep of the concretes of
web and deck, in addition to other parameters, such as relaxation of steel, presence
of untensioned steel, and compression steel etc.
Part B
1. The end block of a post-tensioned PSC beam, 300 x 300 mm is subjected to a
concentric anchorage force of 832.8 kN by a Freyssinet anchorage of area 11720
mm2. Design and detail the anchorage reinforcement for the end block.(NOV-DEC
2009)
2ypo = (/4xd2) (1/2) = (11720)(1/2) = 108.25mm
2yo = 300/2 = 150mm
Ypo/yo = 0.72
Fc = P/A = 832.8/(300x300) = 9.25N/mm2
Fv(max) =fc(0.98 0.825 ypo/yo) = 9.25(0.98 0.825x0.72) = 3.57N/mm2
Fbst = p(0.48 0.4 ypo/yo) = 832.8(0.48-0.4x0.72) = 159.89kN
Ast = Fbst/0.87fy = (159.89x103)/(0.87x260) = 706.85mm2
2. Explain the different types of joints between the walls and floor slab of prestressed
concrete tanks.(NOV-DEC 2009)
3. Explain the effect of varying the ratio of depth anchorage to the depth of end block
on the distribution of bursting tension. (8) (NOV-DEC 2012)
Bursting tensile forces
a) The bursting tensile forces in the end blocks, or regions of bonded posttensioned members, should be assessed on the basis of the tendon jacking load.
For unbonded members, the bursting tensile forces should be assessed on the basis
of the tendon jacking load or the load in the tendon at the limit state of collapse,
whichever is greater ( see Appendix B ).
The bursting tensile force, Fbst existing in an individual square end block loaded
by a symmetrically placed square anchorage or bearing plate, may be derived from
the equation below:
b) The force Fbst will be distributed in a region extending from 0.1 yo to yo from
the loaded face of the end block. Reinforcement provided to sustain the bursting
tensile force may be assumed to be acting at its design strength (0.87 times
characteristic strength of reinforcement) except that the stress should be limited to
a value corresponding to a strain of 0.001 when the concrete cover to the
reinforcement is less than 50 mm.
c) In rectangular end blocks, the bursting tensile forces in the two principal
directions should be assessed on the basis of 18.6.2.2. When circular anchorage or
bearing plates are used, the side of the equivalent square area should be used.
Where groups of anchorages or bearing plates occur, the end blocks should be
divided into a series of symmetrically loaded prisms and each prism treated in the
above manner. For designing end blocks having a cross-section different in shape
from that of the general cross-section of the beam, reference should be made to
specialist literature.
d) Compliance with the requirements of (a), (b) and (c) will generally ensure that
bursting tensile forces along the load axis are provided for. Alternative methods of
design which make allowance for the tensile strength of the concrete may be used,
in which case reference should be made to specialist literature.
e) Consideration should also be given to the spalling tensile stresses that occur in
end blocks where the anchorage or bearing plates are highly eccentric; these reach
a maximum at the loaded face.
4. (i) Explain the general features of prestressed concrete tanks. (8)

(ii) Explain the junctions of tank wall and base slab with neat sketch. (8) (NOVDEC 2012)
Joint in the concrete introduced for convenience in construction at which
special measures are taken to achieve subsequent continuity without provision for
further relative movement, is called a construction joint. A typical application is
between successive lifts in a reservoir.
The position and arrangement of all construction joints should be predetermined

by the engineer. Consideration should be given to limiting the number of such
joints and to keeping them free from possibility of percolations in a similar
manner to contraction joints.
A gap temporarily left between the concrete of adjoining parts of a structure which
after a suitable interval and before the structure is put into use, is filled with mortar
or concrete either completely ( Fig. 5A) or as provided below, with the inclusion
of suitable jointing materials ( Fig. 5B and SC). In the former case the width of the
gap should be sufficient to allow the sides to be prepared before filling.
Where measures are taken for example, by the inclusion of suitable jointing
materials to maintain the water tightness of the concrete subsequent to the filling
of the joint, this type of joint may be regarded as being equivalent to a contraction
joint ( partial or complete ) as defined above.
5. (a) What are the different types of joints used between the slab of prestressed
concrete tanks.
Joints shall be categorized as below:
a) Movetnent Joints - There are three categories of movement joints:
contraction joint - A movement joint with a deliberate discontinuity but no initial
gap between the concrete on either side of the joint, the joint being intended to
accommodate contraction of the concrete ( see Fig. 1 ).
A distinction should be made between a complete contraction joint (see Fig. 1A )
in which both concrete and reinforcing steel are interrupted, and a partial
contraction joint (. see Fig. 1B ) in which only the concrete is interrupted, the
reinforcing steel running through.
Expansion joint - A movement joint with complete discontinuity in both
reinforcement and concrete and intended to accommodate either expansion or
contraction of the structure (see Pig. 2).
In general, such a joint requires the provision of an initial gap between the
adjoining parts of a structure which by closing or opening accommodates the
expansion or contraction of the structure. Design of the joint so as to incorporate
sliding surfaces, is not, however, precluded and may sometimes be advantageous.
b) Construction Joint-A joint in the concrete introduced for convenience in

construction at which special measures are taken to achieve subsequent continuity
without provision for further relative movement, is called a construction joint. A
typical application is between successive lifts in a reservoir.
The position and arrangement of all construction joints should be predetermined

by the engineer. Consideration should be given to limiting the number of such
joints and to keeping them free from possibility of percolations in a similar
manner to contraction joints.
c) Temporary Open Joints - A gap temporarily left between the concrete of
adjoining parts of a structure which after a suitable interval and before the
structure is put into use, is filled with mortar or concrete either completely ( Fig.
5A) or as provided below, with the inclusion of suitable jointing materials ( Fig.
5B and SC). In the former case the width of the gap should be sufficient to allow
the sides to be prepared before filling.
Where measures are taken for example, by the inclusion of suitable jointing
materials to maintain the water tightness of the concrete subsequent to the filling
of the joint, this type of joint may be regarded as being equivalent to a contraction
joint ( partial or complete ) as defined above.
(b) Design the circular tank (only procedure).(NOV-DEC 2010) .(NOV-DEC

2010)
in the construction of concrete structures for the storage of liquids, the
imperviousness of concrete is an important basic requirement. Hence, the design
of such construction is based on avoidance of cracking in the concrete. The
structures are prestressed to avoid tension in the concrete. In addition, prestressed
concrete tanks require low maintenance. The resistance to seismic forces is also
satisfactory.
Prestressed concrete tanks are used in water treatment and distribution systems,
waste water collection and treatment system and storm water management. Other
applications are liquefied natural gas (LNG) containment structures, large
industrial process tanks and bulk storage tanks. The construction of the tanks is in
the following sequence. First, the concrete core is cast and cured. The surface is
prepared by sand or hydro blasting. Next, the circumferential prestressing is
applied by strand wrapping machine. Shotcrete is applied to provide a coat of
concrete over the prestressing strands.
Analysis
The analysis of liquid storage tanks can be done by IS:3370 - 1967, Part 4, or by
the finite element method. The Code provides coefficients for bending moment,
shear and hoop tension (for cylindrical tanks), which were developed from the
theory of plates and shells. In Part 4, both rectangular and cylindrical tanks are
covered. Since circular prestressing is applicable to cylindrical tanks, only this
type of tank is covered in this module.
The following types of boundary conditions are considered in the analysis of the
cylindrical wall.
a) For base: fixed or hinged
b) For top: free or hinged or framed.
For base
Fixed: When the wall is built continuous with its footing, then the base can be
considered to be fixed as the first approximation.
Hinged: If the sub grade is susceptible to settlement, then a hinged base is a
conservative assumption. Since the actual rotational restraint from the footing is
somewhere in between fixed and hinged, a hinged base can be assumed.
The base can be made sliding with appropriate polyvinyl chloride (PVC) waterstops for liquid tightness.
For top
Free: The top of the wall is considered free when there is no restraint in expansion.
Hinged: When the top is connected to the roof slab by dowels for shear transfer,
the boundary condition can be considered to be hinged.
Framed: When the top of the wall and the roof slab are made continuous with
moment transfer, the top is considered to be framed. The hydrostatic pressure on
the wall increases linearly from the top to the bottom of the liquid of maximum
possible depth. If the vapour pressure in the free board is negligible, then the
pressure at the top is zero. Else, it is added to the pressure of the liquid throughout
the depth. The forces generated in the tank due to circumferential prestress are
opposite in nature to that due to hydrostatic pressure.
If the tank is built
underground, then the earth pressure needs to be considered. The hoop tension in
the wall, generated due to a triangular hydrostatic pressure is given as follows.
The hoop tension in the wall, generated due to a triangular hydrostatic pressure is
given as follows.
T = CT w H Ri (9-6.15)
The bending moment in the vertical direction is given as follows.
M = CM w H3 (9-6.16)
The shear at the base is given by the following expression.
V = CV w H2 (9-6.17)
In the previous equations, the notations used are as follows.
CT = coefficient for hoop tension
CM = coefficient for bending moment

CV = coefficient for shear
w = unit weight of liquid
H = height of the liquid
Ri = inner radius of the wall.
The values of the coefficients are tabulated in IS:3370 - 1967, Part 4, for various
values of H2/Dt, at different depths of the liquid. D and t represent the inner
diameter and the thickness of the wall, respectively. The typical variations of CT
and CM with depth, for two sets of boundary conditions are illustrated.
The roof can be made of a dome supported at the edges on the cylindrical wall.
Else, the roof can be a flat slab supported on columns along with the edges.
IS:3370 - 1967, Part 4, provides coefficients for the analysis of the floor and roof
slabs.
Design
IS:3370 - 1967, Part 3, provides design requirements for prestressed tanks. A few
of them are mentioned.
1) The computed stress in the concrete and steel, during transfer, handling and
construction, and under working loads, should be within the permissible values as
specified in IS:1343 - 1980.
2) The liquid retaining face should be checked against cracking with a load factor
of 1.2. CL/WL 1.2 (9-6.18)
Here,
CL = stress under cracking load
WL = stress under working load.
Values of limiting tensile strength of concrete for estimating the cracking load are
Specified in the Code.
3) The ultimate load at failure should not be less than twice the working load.
4) When the tank is full, there should be compression in the concrete at all points
of at least 0.7 N/mm2. When the tank is empty, there should not be tensile stress
greater than 1.0 N/mm2. Thus, the tank should be analysed both for the full and
empty conditions.
5) There should be provisions to allow for elastic distortion of the structure during
prestressing. Any restraint that may lead to the reduction of the prestressing force,
should be considered.
6. (a) What are the design considerations of prestressed concrete poles? (4)
The pre stressed concrete pole for power transmission line are generally designed
as member with uniform prestress since they are subjected to bending moment of
equal magnitude in opposite directions. The poles are generally designed for
following critical load conditions,
1. Bending due to wind load on the cable and on the exposed face.
2. Combined bending and torsion due to eccentric snapping of wire.
3. Maximum torsion due to skew snapping of wires.
4. Bending due to failure of all the wires on one side of the pole.
5. Handling and erection stresses.
(b) What are the advantages of partially prestressed concrete poles?

Resistance to corrosion in humid and temperature climate and to erosion in
desert areas.
Freeze thaw resistance in cold region.
Easy handling due to less weight than other poles
Fire resisting, particularly grassing and pushing fire near ground line.
Easily installed in drilled holes in ground with or without concrete fill.
Lighter because of reduced cross section when compared with reinforced
concrete poles.
Clean and neat in appearance and requiring negligible maintenance for a
number of years, thus ideal suited for urban installation.
SUDHARSAN ENGINEERING COLLEGE

DEPARTMENT OF CIVIL ENGINEERING
SUBJ. CODDE AND NAME: CE 1402 PRESTRESSED CONCRETE STRUCTURES
FACULTY NAME: S.ARUNKUMAR
CLASS &SEC :IV yr CIVIL
Academic year: 2013-14
Semester :VI
UNIT 4
Part A
1. Sketch the arrangement of Tendons & anchorages in circular prestressing of
concrete pipe.(NOV-DEC 2009)
2. Give the advantages of precast prestressed units.(NOV-DEC 2009)
The C/S is more efficiently utilized when compared with a RC section
Effective saving in use of materials.
Improves the ability of material for energy absorption under impact load.
The economy of PSC is well established for long span structures.
There is considerable saving on the quantity of materials used in it.
3. How do you compute the shrinkage and resultant stresses in composite member?
(NOV-DEC 2012)
4. Distinguish between propped and unpropped construction methods. (NOV-DEC
2012)
Here,
A = area of the precast web
c = distance of edge from CGC of precast web
/
c = distance of edge from CGC of composite section

e = eccentricity of CGS
I = moment of inertia of the precast web
/
I = moment of inertia of the composite section.
5. What is circular prestressing?(NOV-DEC 2010)

The term refers to prestressing in round members such as tanks and pipes.
Liquid retaining structures such as circular pipes,tanks and pressure vessels are
admirably suited for circular prestressing.
6. What are the advantages of prestressed concrete sleepers?(NOV-DEC 2010)

It is economical.
Full cross-section of member is utilized.
Increases durability.
Reduces corrosion of steel.
Increase in shear capacity.
Larger spans can be constructed.
It allows rapid construction.
Part B
1. A precast pre-tensioned beam of rectangular section has a breadth of 100 mm and
a depth of 200 mm. The beam with an effective span of 5 m is prestressed by
tendons with their centroid coinciding with the bottom kern. The initial force in
the tendons is 150 kN. The loss of prestress may be assumed to be 157%. The
beam is incorporated in a composite T-beam by casting a top flange of breath 400
mm and t = 400 mm. If a composite beam supports a live load of 1 kN/m.
Calculate the resultant stresses developed in precast & in-situ cast concrete.
(NOV-DEC 2009)
Stress in pre tensioned beam:
A = 20000mm2
Z = (100x2002)/6 = 666.67x103mm2
Self weight of pre tensioned beam = 0.1x0.2x24 = 0.48kN/m
Self weight moment = (0.48x52)/8 = 1.5kNm
Stress at top & bottom = (1.5x106/666.67x103) = 2.25N/mm2
Stress in cast insitu slab:
A = 16000mm2
Z = (400x402)/6 = 10.6x103mm2
Self weight of pre tensioned beam = 0.4x0.04x24 = 3.84kN/m
Self weight moment = (0.348x52)/8 = 1.2kNm
Stress at top & bottom = (1.2x106/10.6x103) = 1.13N/mm2
Stress in composite member
Ixx = (400x403)/12 - (300x2003)/12 = 1.9x109mm4

Zt= (1.9x109)/233.3 = 8.14x106mm2
Zb = (1.9x109)/366.7 = 5.18x106mm2
Live load moment = (1x52)/8 = 2.08kNm
Stress at top = (2.08x106/8.14x106) = 0.25N/mm2
Stress at bottom = (2.08x106/5.18x106) = 0.45N/mm2
2. A composite T-girder of span 5 m is made up of a pre-tensioned rib, 100 mm wide
by 200 mm depth, with an in situ cast slab, 400 mm wide and 40 mm thick. The
rib is prestressed by a straight cable having an eccentricity of 33.33 mm and
carrying initial force of, 150 kN. The loss of prestress is 15%. Check the
composite T-beam for the limit state of deflection if its supports an imposed load
of 3.2 kN/m for (i) unpropped(ii) propped. Assume modulus of Elasticity of 35
kN/mm2 for both precast & in situ cast elements.(NOV-DEC 2009)
Properties of precast prestressed beam
A = 20000 mm2
g = 0.1x0.2x24 = 0.48 kN/m
I = (100x2003)/12 = 66.66x106 mm4
Properties of composite section
A = 16000 mm2
g = 0.04x0.4x24 = 0.384 kN/m
yb = 146mm
yt = 94mm
I = 226x106 mm4
Deflection of prestressed beam
ap = (pel2)/(8EI) = -6.69mm(upward)
Deflection of composite beam due to self weight
ag+q = (5wl4)/(384EI)
q = 8kN/m
g = (0.48 + 0.384) = 0.864kN/m
w = (g+q) = 0.864+8 = 8.864kN/m

ag+q = 9.12mm
Long term deflection
aRL = (1+)( a p + ag+q) = (1+1.6)(0.85(-6.69)+9.12) = 8.99mm
Permissible limit according to IS 1343,
Span/250 = 5000/250 = 20mm.
Hence the actual deflection is within the Permissible limit
3. i) Explain the types of composite construction with neat sketch. (8)
(ii) Explain the precast prestressed concrete stresses at serviceability limit state.
(8)(NOV-DEC 2012)
Limit State of Serviceability : Deflection The deflection of a structure or part
thereof shall not adversely affect the appearance or efficiency of the structure or
finishes or partitions. The deflection shall generally be limited to the following:
a) The final deflection, due to all loads including the effects of temperature, creep
and shrinkage and measured from the as-cast level of the supports of floors, roofs
and all other horizontal members, should not normally exceed span/250.
b) The deflection including the effects of temperature, creep and shrinkage
occurring after erection of partitions and the application of finishes should not
normally exceed span/350 or 20 mm whichever is less.
c) If finishes are to be applied to prestressed concrete members, the total upward
deflection should not exceed span/300, unless uniformity of camber between
adjacent units can be ensured.
Limit State of Serviceability : Cracking Cracking of concrete shall not affect
the appearance or durability of the structure. The criteria of limit state of cracking
for the three types of prestressed concrete members shall be as follows:
a) For type 1, no tensile stresses.
b) For type 2, tensile stresses are allowed but no visible cracking.
c) For type 3, cracking is allowed, but should not affect the
appearance or durability of the structure; the acceptable limits of cracking would

vary with the type of structure and environment and will vary between wide limits
and the prediction of absolute maximum width is not possible.
4. (a) What are shear connectors? Explain the different types of shear connectors in
detail.
(b) A PSC beam of cross section 150 mm x 300 mm is SS over a 6pan of 8m and
is prestressed by means of symmetric parabolic cables @ a distance of 76 mm
from the soffit @ mid span and 125 mm @ top @ support section. If the force in
the cable ie 350 KN. Calculate deflection @ midspan the beam is supporting its
own weight The point load which must be applied at midspan to restore the beam
to the level of its support. (8)(NOV-DEC 2010)
5. A composite T-section is made up of a pretension rib 100 mm wide and 200 mm
deep and a cast in situ slab 400 mm wide and 40 mm thick baring a modulus of
elasticity of 28 kN/mm2. lf the differential shrinkage is 100x104 units. Determine
the shrinkage stresses developed in the precast and cast in situ units. (16)(NOVDEC 2010)
Properties of composite section
A = 36000 mm2
Yt = ((400x40x20)+(200x100x140))/36000 = 86.66mm
Yb = 153.33mm
Ixx = (400x2403)/12 - (300x2003)/12 = 260x106mm4
Zt= (260x106)/86.67 = 3x106mm2
Zb = (260x106)/153.33 = 1.7x106mm2
Zj = (260x106)/40 = 6.5x106mm2
Uniform tensile stress in cast insitu slab = ecs.Ec = 100x10-6x28x103 = 2.8 N/mm2
Pre stressing force = ecs.Ec.A = 2.8x16000 = 44.8kN
Eccentricity of force =86.67-20 = 66.67mm
Moment = 44.8x103x66.67 = 2.99x106Nmm
Direct compressive stress = 44.8/36000 = 1.24 N/mm2
Bending stress:
Stress at top = (2.99x106/3x106) = 0.9N/mm2
Stress at bottom = (2.99x106/1.7x106) = 1.75N/mm2
Stress at junction = (2.99x106/ 6.5x106) = 0.46N/mm2
Shrinkage stresses:
a. In PSC beam
At top = 1.24+0.46 = 1.7 N/mm2
At bottom = 1.24 1.75 = -0.55 N/mm2
b. In insitu slab
At top = 1.24+0.99-2.8 = -0.57 N/mm2
At bottom = 1.24 +0.36 -2.8 = -1.2 N/mm2

Ce2404 Pcs Notes

Uploaded by

Copyright:

Available Formats

Ce2404 Pcs Notes

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ce2404 Pcs Notes

Uploaded by

Copyright:

Available Formats

www.Vidyarthiplus.

UNIT-I INTRODUCTION THEORY AND BEHAVIOUR

4. Define Kern Distance.

b) Describe briefly Fressinet system of post tensioning

Imposed load and self weight

PRESTRESSED CONCRETE STRUCTURES

Limited tensile stresses are permitted in concrete under service

The excessive upward deflections, especially in bridge structure

SUDHARSAN ENGINEERING COLLEGE

CLASS &SEC :IV yr CIVIL

Academic year: 2013-14

2. Sketch the correct arrangement of sheet cage in anchorage zone.(NOV-DEC 2009)

3. Define two stage constructions.(NOV-DEC 2012)

4. (i) Explain the general features of prestressed concrete tanks. (8)

The position and arrangement of all construction joints should be predetermined

b) Construction Joint-A joint in the concrete introduced for convenience in

The position and arrangement of all construction joints should be predetermined

(b) Design the circular tank (only procedure).(NOV-DEC 2010) .(NOV-DEC

If the tank is built

CM = coefficient for bending moment

(b) What are the advantages of partially prestressed concrete poles?

SUDHARSAN ENGINEERING COLLEGE

CLASS &SEC :IV yr CIVIL

Academic year: 2013-14

2. Give the advantages of precast prestressed units.(NOV-DEC 2009)

The C/S is more efficiently utilized when compared with a RC section

Effective saving in use of materials.

The economy of PSC is well established for long span structures.

There is considerable saving on the quantity of materials used in it.

c = distance of edge from CGC of composite section

I = moment of inertia of the composite section.

5. What is circular prestressing?(NOV-DEC 2010)

6. What are the advantages of prestressed concrete sleepers?(NOV-DEC 2010)

Ixx = (400x403)/12 - (300x2003)/12 = 1.9x109mm4

w = (g+q) = 0.864+8 = 8.864kN/m

appearance or durability of the structure; the acceptable limits of cracking would

You might also like