DatasheetSMT 160 Temp Sens

Temperature sensor
with
digital output
Specification sheet
SMT 160-30
Contents
1.Introduction
page 2
2. Smart temperature sensor
page 2
3. Pin-out and housing
page 4
4. Product discription
page 5
5. Specifications
page 6
6. Understanding the specifications page 7

7. General operation
page 9
page - 1 -
1. Introduction
The Smartec temperature sensor is a sophisticated full silicon temperature sensor with a
digital output. The one wire (duty cycle) output can be connected to all kind of microcontrollers directly without the need of A/D conversion. The temperature range is
45 C to 150 C. The sensor is available in various housing like T018, T092, T0220
and for high volume production in SOIC.
2. Smart temperature sensor

Most important features
* No A-D converter necessary
* Absolute accuracy .7 C
* Linear output within .2 C
* Output fully digital interpretable
* Output fully analogue interpretable
* Calibrated on chip.
* TTL, CMOS compatible
* Temperature range 175 C (-45 to +130 C)
* Directly connectable to data input of micro processor
* Easy multiplexing when using more sensors to one micro processor
* Low power consumption (< 1 mW)
Typical applications
* Heater systems
* Air conditioners
* Climatizing units
* Washing machines
* Overheating protection
* Appliances
page - 2 -
Product highlights
1.
The SMART TEMPERATURE SENSOR represents a significant totally new

development in transducer technology. Its new on-chip interface responds to the
progressively stringent demands of both the consumer and industrial electronics
sectors for a temperature sensor directly connectable to microprocessor input and
thus capable of direct and reliable communication with microprocessors.
The SMART TEMPERATURE SENSOR features a duty-cycle modulated square

waveoutput voltage with linear response to temperatures in the -45 C to +130 C
range to an accuracy of better than 1.2 C. In the range from -30 to +100 C the
linearity is better than 0.2 C. (TO18)
3.
The SMART TEMPERATURE SENSOR is calibrated during test and burn-in of

the chip. The integral modulator ensures that the sensor unit can communicate
effectively with low-cost processors without the need of (onboard) A-D convertors.
The SMART TEMPERATURE SENSOR combines digital output and on-chip

calibration to ensure major cost reductions and performance-related advantages.
5.
Direct connection of the sensor output to the microprocessor input reduces the
number of components and terminals to a minimum, cutting costs and boosting
reliability.
6.
In applications where more sensors are used, easy multiplexing can be obtained by
using more micro processor inputs or by using simple and cheap digital
multiplexers.
7.
Since the sensor requires no subsequent calibration, optimal cost savings are
recorded both during manufacturing and in the course of after-sales servicing.
page - 3 -
3. Pin-out and housing

SO8L housing
6.1 mm
HE housing
Pin 1
2.5
8.0 mm
2
3
1 2 3
1 3 2
TO-92 housing
TO-18 housing
bottom view
TO-220 housing
housing / pinning
TO-18
TO-92
TO-220
SO8L
HE
+ V cc
Pin 2
Pin 2
Pin 2
Pin 1
Pin 2
GND
Pin 3
Pin 3
Pin 3
Pin 7
Pin 3
Output
Pin 1
Pin 1
Pin 1
Pin 8
Pin 1
page - 4 -
4. Product description
The SMT160-30 is a three terminal integrated temperature sensor, with a duty-cycle
output. Two terminals are used for the power supply of 5 Volts and the third terminal
carries the output signal. A duty cycle modulated output is used because this output is
interpretable by a micro-processor without A-D converter, while the analogue
information is still available.
The SMT160-30 (TO18 model) has an overall accuracy of 0.7 C in the range from -30
C to +100 C and an accuracy of 1.2 C from
-45 to +130 C. This makes the sensor especially useful in all applications where
"human" (climate control, food processing etc.) conditions are to be controlled.
The C-mos output of the sensor can handle cable length up to 20 meters. This makes the
SMT160-30 very useful in remote sensing and control applications.
Parameters
Value
unit
Supply voltage
4.75 - 7
Supply current
max 200
Short circuit protection
infinite (within supply

voltage range)
Operating temperature
range
-45 to +130
Storage temperature
-50 to +150
page - 5 -
5. Specifications
TO18
TO92
TO220
HE
SOIC
parameters
min.
typ
max.
max. 1
max.
max.
max.
Units
Supply voltage 2
4.75
V.
Supply current
160
200
A.
130
-30 + 100 C
0.7
1.2
1.7
1.5
-45 + 130 C
1.2
1.7
1.5
1.5
Non-linearity 5
0.2
0.4
0.5
1.0
1.0
Supply voltage
sensitivity
0.1
C/V
Repeatability
0.1
0.2
0.2
0.2
0.2
Long term drift
0.05
0.05
temperature range 3 -45

Total accuracy 4
Output:
- duty cycle =
0.320 + 0.00470*t (t = temperature in C)
-frequency
Khz
- noise
0.005
- impedance
200
Ohm
All not mentioned specifications are the same as TO18
Case connected to ground
The SMT 30-160-18 can be used from -65 to +160 C for a short periods without physical
damage to the device. The specified accuracy applies only to the rated performance
temperature range.
Total accuracy includes all errors.
Applicable from -30 to +100 C
page - 6 -
6. Understanding the specifications.

The way in which the SMT160-30 is specified makes it easy to apply in a wide variety
of different applications. It is important to understand the meaning of the various
specifications and their effects on accuracy. The SMT160-30 is basically a bipolar
temperature sensor, with accurate electronics to convert the sensor signal into a duty
cycle. During production the devices are calibrated.
The output signal

As stated in the specifications the output is a square wave with a well-defined
temperature-dependent duty cycle. The duty cycle of the output signal is linearly related
to the temperature according to the equation:
D.C. = 0.320+0.00470*t
D.C. = duty cycle

t = Temperature in C
Easy calculation shows that for instance that at 0 C the

D.C.= 0.320 or 32.0 % and at 130 C the
D.C.= 0.931 or 93.1 %
Total accuracy
The above mentioned equation is the nominal one. The maximum deviation from the
nominal equation is defined as total accuracy. With temperatures above 100 C the
accuracy decreases.
Non linearity
Non-linearity as it applies to the SMT160-30 is the deviation from the best-fit straight
line over the whole temperature range. For the temperature range of -30 C to +100 C
the non-linearity is less than 0.2 C (TO18).
Long-term drift
This drift strongly depends on the operating condition. At room temperature the drift is
very low (< 0.05 C). However at higher temperatures the drift will be worse, mainly
because of changes in mechanical stresses. This drift is partly irreversible and causes
non-ideal repeatability and long-term effects. At temperatures above
100 C but in the operating range a long-term drift better than 0.1 C is to be expected.
page - 7 -
Noise
The resolution is better than 0.005 C. The standarddeviation of the noiselevel
(measured over a 20 ms. period) is below this 0.005 C.
Time constants
The time constants of the sensor is measured under different circumstances. To compare
this with other types of sensors the same kind of measurements were done. The time
constant is defined as the time required to reach 63% of an instananeous temperature
change.
condition
time constant
(sec) (TO18)
mounted in an alu block of a certain

temperature (mean value of different
measurements)
0.6
in a bath filled with oil that was

stirred
1.4
(mean value of different

measurements)
Moving air with a speed of about 3
m/s
13.5
- without heatsink
Moving air with a speed of about 3
m/s
5.0
- with heatsink
Non moving air
60
- without heatsink
Non moving air
100
- with heatsink
The above mentioned figures are hard to measure, an accuracy of around 5 % is a reasonable
estimation. These figures only concern the sensor built in a TO-18 housing and not the TO92 nor the chip itself.
page - 8 -
7. General operation
An easy way of measuring a duty cycle is to use a microcontroller. It is only necessary
to connect the sensors output to one of the microcontrollers inputs. With help of a small
program it is possible to sense that input wether it is high or low. The speed of this
sampling is limited due to the instruction time of the controller. So to achieve the
wished accuracy it is necessary to sample over more than one sensor period. This way
of working has also the advantage to filter noise. From the theory of signal processing it
can be derived that there is a fixed ratio between the sensors signal frequency, the
sampling rate and the sampling noise. This sampling noise limits the accuracy and
amounts to:
Terror= 200 * t s /sqrt(6*tm *tp)

Terror = measurement error (= standard deviation of the sampling noise)
ts
= microcontrollers sampling rate
tm
= total measurement time
tp
= output signal periodicity of the sensor
Microcontrollers can sample at a high frequency so with a small program it is possible

to measure the sensor's duty cycle within 50 ms and a resolution of .01 C.
NOTE:
The above mentioned error has in principle nothing to do with the accuracy of the
sensor; it gives only an impression of the accuracy of measuring duty cycles with
microcontrollers (standard deviation).
For more information how to measure duty cycles with microcontrollers we refer to our
application notes.
For additional information and/or samples, please contact:
page - 9 -

DatasheetSMT 160 Temp Sens

Uploaded by

Copyright:

Available Formats

DatasheetSMT 160 Temp Sens

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DatasheetSMT 160 Temp Sens

Uploaded by

Copyright:

Available Formats

Temperature sensor

2. Smart temperature sensor

3. Pin-out and housing

6. Understanding the specifications page 7

2. Smart temperature sensor

The SMART TEMPERATURE SENSOR represents a significant totally new

The SMART TEMPERATURE SENSOR features a duty-cycle modulated square

The SMART TEMPERATURE SENSOR is calibrated during test and burn-in of

The SMART TEMPERATURE SENSOR combines digital output and on-chip

3. Pin-out and housing

Short circuit protection

infinite (within supply

Long term drift

temperature range 3 -45

0.320 + 0.00470*t (t = temperature in C)

All not mentioned specifications are the same as TO18

Case connected to ground

Total accuracy includes all errors.

Applicable from -30 to +100 C

6. Understanding the specifications.

The output signal

D.C. = duty cycle

Easy calculation shows that for instance that at 0 C the

mounted in an alu block of a certain

in a bath filled with oil that was

(mean value of different

Terror= 200 * t s /sqrt(6*tm *tp)

= microcontrollers sampling rate

= total measurement time

= output signal periodicity of the sensor

Microcontrollers can sample at a high frequency so with a small program it is possible

For additional information and/or samples, please contact:

You might also like

Terror= 200 * t s /sqrt(6tm tp)