Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
23 views

Lecture-3 (Microprocessors and Microcontrollers)

This document discusses microprocessors and microcontrollers, specifically the 8051. It covers machine cycles, delay calculations using NOP instructions and nested loops, I/O port programming, and single bit instructions. The main topics are how the 8051 machine cycle works based on crystal frequency, using NOP and loops to generate delays, programming the I/O ports P0-P3 including individual bit access, and instructions like JNB and JB for single bit operations.

Uploaded by

KhuleedShaikh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
23 views

Lecture-3 (Microprocessors and Microcontrollers)

This document discusses microprocessors and microcontrollers, specifically the 8051. It covers machine cycles, delay calculations using NOP instructions and nested loops, I/O port programming, and single bit instructions. The main topics are how the 8051 machine cycle works based on crystal frequency, using NOP and loops to generate delays, programming the I/O ports P0-P3 including individual bit access, and instructions like JNB and JB for single bit operations.

Uploaded by

KhuleedShaikh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 31

Microprocessors and

Microcontrollers
(EE-231)

Main Objectives
Machine Cycle and Time Delay of 8051
I/O port programming of 8051

Machine Cycle
CPU executing an instruction takes a certain number of
clock cycles which are referred as to as machine cycles.
The length of machine cycle depends on the frequency of
the crystal oscillator connected to 8051
In original 8051, one machine cycle lasts 12 oscillator
periods. 4K
32K

Delay Calculation
Example

4K
32K

Delay Calculation
Example

4K

Solution

32K

Delay Using NOP

NOP instruction takes 1 Machine Cycle and does nothing. So it can be


used for generating delay.
Example

4K
32K

Delay Using Nested Loops


Example

4K
32K

Delay for other 8051s

Two factors can affect the accuracy of the delay


Crystal frequency
The duration of the clock period of the machine cycle is a function of
this crystal frequency
8051 design
The original machine cycle duration was set at 12 clocks
Advances in both IC technology and CPU design in recent years have
made the 1-clock machine cycle a common feature
32K

Delay for other 8051s

32K

I/O Port Programming

32K

Ground

I/O Ports

The four 8-bit I/O ports P0, P1, P2 and P3 each uses 8 pins
All the ports upon RESET are configured as input, ready to be used as
input ports
When the first 0 is written to a port, it becomes an output
To reconfigure it as an input, a 1 must be sent to the port
To use any of these ports as an input port, it must be programmed
32K

I/O port
internal
structure

Port 0

It can be used for input or output


Each pin must be connected externally to a 10K ohm pull-up resistor
This is due to the fact that P0 is an open drain, unlike P1, P2, and P3
Open drain is a term used for MOS chips in the same way that open
collector is used for TTL chips.

32K

Port 0

In order to make port 0 an input, the port must be programmed by


writing 1 to all the bits

32K

Port 0 is also designated as AD0-AD7, allowing it to be used for both


address and data
When connecting an 8051/31 to an external memory, port 0 provides
both address and data

Port 1

Port 1 can be used as input or output


In contrast to port 0, this port does not need any pull-up resistors since
it already has pull-up resistors internally
Upon reset, port 1 is configured as an input port

32K

To make port 1 an input port, it must be programmed as such by


writing 1 to all its bits

Port 2
Port 2 can be used as input or output
Just like P1, port 2 does not need any pull-up resistors since
it already has pull-up resistors internally
Upon reset, port 2 is configured as an input port
To make port 2 an input port, it must be programmed as
such by writing 1 to all its bits
In 8031-based systems, port 2 must be used along with P0
to provide the 16-bit address for the external memory
Port 2 is also designated as A8 A15, providing upper
address
Port 0 provides the lower 8 bits via A0 A7

Port 3

Port 3 can be used as input or output and does not need any pull-up
resistors
Port 3 is configured as an input port upon reset
Port 3 provides some extremely important signals

32K

Different way of accessing Ports

32K

I/O Bit Manipulation Programming

Sometimes we need to access only 1 or 2 bits of the port, in that case


we use bit-manipulation programming
I/O ports of 8051 are bit addressable i.e., there bits can be individually
programmed

32K

I/O Bit Manipulation Programming

These are the bit names for different ports

32K

Bit Addressability of I/O ports

32K

Single Bit Instructions

Instructions that are used for signal-bit operations are as following

32K

Single Bit Instructions

The JNB and JB instructions are widely used single-bit operations


They allow you to monitor a bit and make a decision depending on
whether its 0 or 1
These instructions resemble if-else in C
These two instructions can be used for any bits of I/O ports 0, 1, 2, and
3
32K

Checking an Input Bit

32K

Checking an Input Bit

32K

Checking an Input Bit

32K

Reading a single Bit into Carry Flag

32K

Reading a single Bit into Carry Flag

Reading Input Pins vs Port Latch


In reading a port
Some instructions read the status of port pins
Others read the status of an internal port latch

Therefore, when reading ports there are two possibilities:


Read the status of the input pin
Read the internal latch of the output port
Confusion can cause errors in programming, especially when external
hardware is concerned

Reading Latch for Output port


Some instructions read the contents of an internal port
latch instead of reading the status of an external pin
For example, look at the ANL P1,A instruction and the
sequence of actions is executed as follow
1. It reads the internal latch of the port and brings that data
into the CPU
2. This data is ANDed with the contents of register A
3. The result is rewritten back to the port latch
4. The port pin data is changed and now has the same value
as port latch

Read Modify Write


Read-Modify-Write instructions
Read the port latch
Perform an Operation on the value and then
Rewrite it back to the port latch

Read Modify Write


The ports in 8051 can be accessed by the Read-modify-write technique
This feature saves many lines of code by combining in a single
instruction all three actions
Reading the port
Modifying it
Writing to the port

You might also like