Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 147 views

    GTST Protection Test

    Uploaded by

    luriah
    This document outlines procedures for testing the automatic start functions of various turbine lubrication pumps. It describes 5 steps: 1) Preparation and confirmation of operational data for the fluid coupling and protective devices. 2) Criteria for automatic start pressures of the main lube oil pump (MOP), emergency lube oil pump (EBOP), and emergency seal oil pump (ESOP). 3) Process for testing the MOP's automatic start including operating a test to simulate low pressure and verifying both pumps start. 4) Same test for the EBOP using a test valve to simulate low pressure. 5) Same test for the ESOP using the test valve to simulate

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    GTST Protection Test

    Uploaded by

    luriah
    147 views3 pages
    This document outlines procedures for testing the automatic start functions of various turbine lubrication pumps. It describes 5 steps: 1) Preparation and confirmation of operational data for the fluid coupling and protective devices. 2) Criteria for automatic start pressures of the main lube oil pump (MOP), emergency lube oil pump (EBOP), and emergency seal oil pump (ESOP). 3) Process for testing the MOP's automatic start including operating a test to simulate low pressure and verifying both pumps start. 4) Same test for the EBOP using a test valve to simulate low pressure. 5) Same test for the ESOP using the test valve to simulate

    Original Description:

    Gas Turbine Protection Test Procedure

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document outlines procedures for testing the automatic start functions of various turbine lubrication pumps. It describes 5 steps: 1) Preparation and confirmation of operational data for the fluid coupling and protective devices. 2) Criteria for automatic start pressures of the main lube oil pump (MOP), emergency lube oil pump (EBOP), and emergency seal oil pump (ESOP). 3) Process for testing the MOP's automatic start including operating a test to simulate low pressure and verifying both pumps start. 4) Same test for the EBOP using a test valve to simulate low pressure. 5) Same test for the ESOP using the test valve to simulate

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    147 views3 pages

    GTST Protection Test

    Uploaded by

    luriah
    This document outlines procedures for testing the automatic start functions of various turbine lubrication pumps. It describes 5 steps: 1) Preparation and confirmation of operational data for the fluid coupling and protective devices. 2) Criteria for automatic start pressures of the main lube oil pump (MOP), emergency lube oil pump (EBOP), and emergency seal oil pump (ESOP). 3) Process for testing the MOP's automatic start including operating a test to simulate low pressure and verifying both pumps start. 4) Same test for the EBOP using a test valve to simulate low pressure. 5) Same test for the ESOP using the test valve to simulate

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    GT/ ST Protection Test

    - Procedure

    & Test Reports

    Procedure for MOP Auto cut i n Test

    check

    1. PREPARATION & CONFIRMATION


    1-1. CONFIRMATION OF FSNL OPERATION.
    Confirm GT GAS Control valve stability at rated speed.
    1-2. All operational data should be confirmed during "FSNL operation.
    On FSNL operation, protective device checkout is carried out
    Auto start test on MOP/EBOP/ESOP
    CRITERIA
    2-1. MOP Auto Start Header Pressure
    2-2.EBOP Auto Start Header Pressure
    2-3.ESOP Auto Start Header Pressure
    2-4.BRG Oil Header Pressure Low Alarm

    113 psi / 7.79bar


    90psi / 6.2 bar
    90psi / 6.2 bar
    25psi / 1.7 bar

    2-5.BRG Oil Header Pressure Low Trip

    10psi / 0.7

    .Auto start test of MOP


    A)

    MOP{B)AUTO START TEST

    3-1.MOP {A) is running. Check the lube oil Header press


    (>8 Bar) and Lube oil pressure > 1.8 Bar
    3-2. Put the control switch of MOP (B) to be on AUTO, and verify that MOP {B)
    is on standby mode.
    3-3. Operate the Main Lube Pump Test "ON" from Mark-V
    Solenoid valve operate, (draining the oil pressure from the pressure switch
    at the moment when the MOP (B) starts automatically due to lube oil pressure
    low. Make sure the pressure {checked by press. Gauge at turbine front
    standard) Both A & B will be running.

    3-4. Successful completion of test, the Main Lube Pump Test will go
    to "OFF" mode.

    3-5. Stop MOP (A) from Mark-V. MOP (A) AUTO START TEST

    3-6. MOP {B) is running (ln service)


    Check the lube oil Header press (>8 Bar) and Lube oil pressure >
    1.8 Bar

    3-7. Put the control switch of MOP (A) to be on AUTO, and verify that
    MOP (A) is standby.

    3-8.Operate the Main Lube Pump Test "ON" from Mark-V


    Solenoid valve operate, (draining the oil pressure from pressure
    switch) at the moment when the MOP (A) starts automatically due to
    lube oil pressure low. Make sure the pressure (checked by press.
    Gauge at turbine front standard with both A & B running.
    3-9. Successful completion of test, the Main Lube Pump Test will go to
    "OFF" mode.
    3-10.Stop MOP (B) from Mark-V.

    4. Auto start test of ESOP with test valve at local panel)


    4-1.MOP (A) is running Check the Lube Oil Pump Header Press (>8 Bar)
    and Lube Oil Pressure > 1.8 Bar
    4-2.Put the control switch of EBOP to Auto, and verify that EBOP is
    standby mode.
    4-3.Operate the test valve at oil tank gauge panel
    to reduce the detecting pressure of Pressure Switch
    EBOP starts automatically when sensed oil' pressure low'
    4-4.Restore the test valve to normal position.
    4-5. Stop EBOP from Local starter panel, and put CS to "Auto" position.
    4-6.Check that the Brg.oil pressure and Brg. metal temperature are
    steady.

    5. Auto start test of ESOP (with test valve at local)


    5-1. MOP (A) is running Check the Lube Oil Header Press (>8 Bar)
    and Lube Oil Pressure > 1.8 Bar
    5-2.Put the controlswitch of ESOP to Auto, and verify that ESOP is
    standby mode.
    5-3.Operate the test valve at oil tank gauge panel
    to reduce the detecting pressure of Pressure Switch
    confirm ESOP starts automatically when sensed "Low pressure"

    5-4.Restore the test valve to normal position.

    5-5. Stop ESOP from local starter panel, and put CS to "Auto" position.
    5-6.Check that the Brg.oil pressure and Brg. Metal temperature are steady.

    You might also like