8050 JD

1-1-2 Switching Mode Regulator ICs
SI-8000JD Series
Surface-Mount, Separate Excitation Step-down Switching Mode Regulator ICs
Features
Lineup
Surface-mount package (TO263-5)
Part Number
SI-8033JD
SI-8050JD
SI-8090JD
SI-8120JD
VO(V)
3.3
5.0
9.0
12.0
Output current: 1.5A
IO(A)
High efficiency: 77 to 88%

Requires only 4 discrete components
1.5
Absolute Maximum Ratings
Internally-adjusted phase correction and

output voltage
Parameter
Symbol
Ratings
Unit
VIN
43
Output Current
IO
1.5
Power Dissipation*
PD
W
C
DC Input Voltage
Capable of downsizing a choke-coil due to IC's

high switching frequency (125 kHz). (Compared with conventional Sanken devices)
Built-in foldback-overcurrent and thermal
protection circuits
Output ON/OFF available (Circuit current at
output OFF: 200A max)
Junction Temperature
Tj
+125
Storage Temperature
Tstg
40 to +125
Thermal Resistance (Junction to Case)
j-c
C/W
Thermal Resistance (Junction to

Ambient Air)
j-a
33.3
C/W
Conditions
When mounted on glass-epoxy board 40 40 mm (copper

area 100%)
When mounted on glass-epoxy board 40 40 mm (copper

area 100%)
*: Limited by thermal protection circuit
Soft start available by ON/OFF pin Conditions
Applications
Power supplies for telecommunication equipment
Onboard local power supplies, etc.
Recommended Operating Conditions

Ratings
Parameter
Symbol
DC Input Voltage Range
SI-8033JD
SI-8050JD
SI-8090JD
SI-8120JD
VIN1
5.3 to 40
7 to 40
11 to 40
14 to 40
VIN2
6.3 to 40
8 to 40
12 to 40
15 to 40
DC Output Current Range*
Unit
Conditions
IO=0 to 1A
IO=0 to 1.5A
VINVO+3V
IO
0 to 1.5
Operating Junction Temperature Range
Tjop
30 to +125
Operating Temperature Range*
Top
30 to +125
*: Limited by TaPD characteristics
Electrical Characteristics
(Ta=25C)
Ratings
Parameter
Symbol
VO
Output Voltage
SI-8033JD
typ.
max.
min.
3.234
3.30
3.366
4.90
Conditions
Efficiency
Conditions
f
Oscillation Frequency
Conditions
Load Regulation
Temperature Coefficient of Output Voltage
Overcurrent Protection
Starting Current
ON/OFF*
Pin
Conditions
IS1
Conditions
typ.
max.
min.
typ.
max.
5.00
5.10
8.82
9.00
9.18
11.76
12.00
12.24
VIN=21V, IO=0.5A
VIN=24V, IO=0.5A
77
82
86
88
VIN=15V, IO=0.5A
VIN=20V, IO=0.5A
VIN=21V, IO=0.5A
VIN=24V, IO=0.5A
125
125
125
125
VIN=20V, IO=0.5A
80
40
VIN=21V, IO=0.5A
100
VIN=10 to 30V, IO=0.5A
10
10
30
VIN=15V, IO=0.2 to 0.8A
50
10
VIN=20V, IO=0.2 to 0.8A
0.5
1.6
10
mV/ C
1.6
A
VIN=24V
VSSL
0.5
0.5
0.5
0.5
Outflow Current
at Low Voltage
ISSL
100
100
100
100
Quiescent Circuit Current
Conditions
Iq(oFF)
Conditions
VSSL=0V
7
VIN=15V, Io=0A
VIN=20V, Io=0A
200
VIN=15V, VON/OFF=0.3V
VIN=21V, Io=0A
200
*: Pin 5 is the ON/OFF pin. Soft start at power on can be performed with a capacitor connected to
this pin.
The output can also be turned ON/OFF with this pin.
The output is stopped by setting the voltage of this pin to VSSL or lower.
ON/OFF-pin voltage can be changed with an open-collector drive circuit of a transistor.
When using both the soft-start and ON/OFF functions together, the discharge current from C3
flows into the ON/OFF control transistor. Therefore, limit the current securely to protect the
transistor if C3 capacitance is large.
The ON/OFF pin is pulled up to the power supply in the IC, so applying the external voltage is
prohibited.
mA
VIN=24V, Io=0A
200
200
SI-8000JD
SI-8000JD
SI-8000JD
5 ON/OFF
5 ON/OFF
5 ON/OFF
C3
VOUT. ON/OFF
ICs
mV
VIN=24V, IO=0.2 to 0.8A
VIN=21V
Conditions
mV
40
1.0
1.6
VIN=20V
kHZ
130
1.0
1.6
VIN=15V
60
40
VIN=21V, IO=0.2 to 0.8A
0.5
VIN=24V, IO=0.5A
120
40
Low Level Voltage
Iq
46
Unit
min.
VO/Ta
SI-8120JD
max.
VIN=20V, IO=0.5A
25
VOLOAD
Conditions
SI-8090JD
typ.
VIN=15V, IO=0.5A
VIN=15V, IO=0.5A
VOLINE
Line Regulation
SI-8050JD
min.
Soft Start
C3
Soft Start
+VOUT. ON/OFF
SI-8000JD Series
External Dimensions (TO263-5)
(Unit : mm)
0.2
10.0
(8.0)
Case Temperature Measurement Point

0.2
(6.8)
15.30
0.3
0.1
0.2
(R0.3)
0.2
4.9
0.3
2.0
(0.75)
0.2
0.10
Pin Assignment
q VIN
w SWOUT
e GND
r VOS
t ON/OFF
2.4
(R0.3)
2.54
9.2
0.3
15.3
0.15
0.10
(3)
(3)
4.9
0.88
0.2
(4.6)
(2R0.45)
(3)
0.2
0.2
+0.10
1.3 0.05
3-R0.3
1.5 Dp:
(4.4)
0.2
(1.75)
1.2
(0.40)
4.5
9.2
0.2
9.90
(15)
0~6
(0.5)
0.1
0.1
(1.7
0.8
0.25
)
(1.7
0.25
)
1
0.8
0.25
(1.7
)
0.25
(1.7
Plastic Mold Package Type

Flammability: 94V-0
Product Mass: Approx. 1.48g
(3)
(3)
2-R0.3
10.0
0.02
Typical Connection Diagram
Block Diagram
L1
VIN
1
SW OUT
VIN
PReg.
SI-8000JD
OCP
C1
Latch &
Drive
Reset
SW
VIN
5 ON/OFF
ON/OFF
Soft
Start
VS
VOUT
4
+
ON/OFF GND
5
3
Di
C2
C3
OSC
GND
TSD
Comp.
Error Amp.
C1
C2
C3
L1
Di
VREF
GND
3
:
:
:
:
:
GND
50V/220F
25V/470F
10V/0.47F (Only when using soft-start function)
100H
SJPB-H6 (Sanken)
Reference Data
Thermal Resistance (junction to ambient air)

j-a (C/W )
Copper Laminate Area on Glass Epoxy Board vs.

Thermal Resistance (Junction to Ambient Air) (Typical Value)
Output Current vs. Power Dissipation (Typical)
50
Power Dissipation Pd (W)
55
With glass epoxy board of 40 40 mm
45
40
35
30
0
200
400
600
800
1000
1200
1400
1600
1800
Copper Laminate Area (mm2)
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
40V
30V
20V
VIN 8V
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
Output Current IO (A)
Ta-PD Characteristics
3.5
Power Dissipation PD (W)
Copper Area
4040 mm
( j-a : 33.3C/W)
PD=VOIO
2040 mm
( j-a : 37C/W)
2.5
2020 mm
( j-a :44C/W)
1010 mm
( j-a : 53C/W)
100
VO
1 VFIO 1
VIN
The efficiency depends on the input voltage and the output current. Therefore, obtain the value
from the efficiency graph and substitute the percentage in the formula above.
VO : Output Voltage
1.5
VIN : Input Voltage

IO : Output Current
: Efficiency (%)
0.5
VF : D1 forward voltage
0
25
25
50
75
100
125
0.4V(IO=2A)(SJPB-H6)
Ambient Temperature Ta (C)
Thermal design for D1 must be considered separately.
ICs
47

8050 JD

Uploaded by

Copyright:

Available Formats

8050 JD

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

8050 JD

Uploaded by

Copyright:

Available Formats

1-1-2 Switching Mode Regulator ICs

Surface-Mount, Separate Excitation Step-down Switching Mode Regulator ICs

Surface-mount package (TO263-5)

Output current: 1.5A

High efficiency: 77 to 88%

Absolute Maximum Ratings

Internally-adjusted phase correction and

Capable of downsizing a choke-coil due to IC's

Thermal Resistance (Junction to Case)

Thermal Resistance (Junction to

When mounted on glass-epoxy board 40 40 mm (copper

When mounted on glass-epoxy board 40 40 mm (copper

*: Limited by thermal protection circuit

Soft start available by ON/OFF pin Conditions

Recommended Operating Conditions

DC Input Voltage Range

DC Output Current Range*

Operating Junction Temperature Range

Operating Temperature Range*

*: Limited by TaPD characteristics

VIN=10 to 30V, IO=0.5A

VIN=15V, IO=0.2 to 0.8A

VIN=20V, IO=0.2 to 0.8A

Quiescent Circuit Current

VIN=24V, IO=0.2 to 0.8A

VIN=18 to 30V, IO=0.5A

VIN=21V, IO=0.2 to 0.8A

VIN=15 to 30V, IO=0.5A

Low Level Voltage

VIN=8 to 30V, IO=0.5A

External Dimensions (TO263-5)

Case Temperature Measurement Point

Plastic Mold Package Type

Typical Connection Diagram

Thermal Resistance (junction to ambient air)

Copper Laminate Area on Glass Epoxy Board vs.

Output Current vs. Power Dissipation (Typical)

Power Dissipation Pd (W)

With glass epoxy board of 40 40 mm

Copper Laminate Area (mm2)

Output Current IO (A)

Power Dissipation PD (W)

VIN : Input Voltage

Ambient Temperature Ta (C)

Thermal design for D1 must be considered separately.

You might also like