D Escriptio: S Feature
D Escriptio: S Feature
FEATURES
s s s s s s s s
DESCRIPTIO
Operates from a Single 3.3V Supply Low Supply Current: ICC = 200A ICC = 35A in Driver Disable Mode ICC = 0.2A in Shutdown Mode ESD Protection Over 10kV Uses Small Capacitors: 0.1F Operates to 120kBaud Output Overvoltage Does Not Force Current Back into Supplies EIA/TIA-562 I/O Lines Can Be Forced to 25V Without Damage Pin Compatible with LT1180A
The LTC1385 is an ultra-low power, 2-driver/2-receiver EIA / TIA-562 transceiver which operates from a single 3.3V supply. The charge pump requires only four spacesaving 0.1F capacitors. The transceiver operates in one of three modes: Normal, Driver Disable or Shutdown. In the Normal mode, ICC is only 200A in the unloaded condition. In the Driver Disable mode, the charge pump is turned off, the driver outputs are forced into three-state, both receivers are kept active, and ICC drops to 35A. In the Shutdown mode, everything is turned off and ICC drops to 0.2A. The LTC1385 is fully compliant with all data rate and overvoltage EIA / TIA-562 specifications. The transceiver can operate up to 120kbaud with a 1000pF, 3k load. Both driver outputs and receiver inputs can be forced to 25V without damage, and can survive multiple 10kV ESD strikes.
APPLICATI
s s
TYPICAL APPLICATI
VCC = 3.3V
500
0.1F 562 OUTPUT 0.1F
QUIESCENT CURRENT (A)
400 300 200 100 0 20 SHUTDOWN CURRENT 0 20 40 TEMPERATURE (C) 60 QUIESCENT CURRENT
16
U
0.8 0.6 0.4 0.2 0 80
UO
UO
NC 10
DC ELECTRICAL CHARACTERISTICS
VCC = 3.3V, C1 = C2 = C3 = C4 = 0.1F, VON/OFF = VCC, Driver Disable = VCC, unless otherwise noted.
PARAMETER Any Driver Output Voltage Swing Logic Input Voltage Level Logic Input Current Output Short-Circuit Current Output Leakage Current CONDITIONS 3k to GND Positive Negative
q q q q q q q
Input Low Level (VOUT = High) Input High Level (VOUT = Low) VIN = VCC VIN = 0V VOUT = 0V Shutdown or Driver Disable or VCC = 0V (Note 3,4), VOUT = 20V
W W
TOP VIEW DRIVER DISABLE 1 C1+ 2 V+ 3 C1 4 C2+ 5 C2 6 V 7 TR2 OUT 8 RX2 IN 9 18 ON/OFF 17 VCC 16 GND 15 TR1 OUT 14 RX1 IN 13 RX1 OUT 12 TR1 IN 11 TR2 IN 10 RX2 OUT
MAX
UNITS V V V V A A mA A
0.8 5 40 500
LTC1385
DC ELECTRICAL CHARACTERISTICS
VCC = 3.3V, C1 = C2 = C3 = C4 = 0.1F, VON/OFF = VCC, Driver Disable = VCC, unless otherwise noted.
PARAMETER Any Receiver Input Voltage Thresholds Hysteresis Input Resistance Output Voltage Output Short-Circuit Current Output Leakage Current Power Supply Generator V + Output Voltage V Output Voltage Supply Rise Time Power Supply VCC Supply Current Supply Leakage Current (VCC) Digital Input Threshold Low Digital Input Threshold High CONDITIONS Input Low Threshold Input High Threshold 10V VIN 10V Output Low, IOUT = 1.6mA (VCC = 3.3V) Output High, IOUT = 160A (VCC = 3.3V) Sinking Current, VOUT = VCC Sourcing Current, VOUT = 0V Shutdown (Note 4), 0V VOUT VCC IOUT = 0mA IOUT = 5mA IOUT = 0mA IOUT = 5mA Shutdown or Driver Disable to Turn-On No Load (Note 2) Shutdown (Note 4) Driver Disable (Note 3)
q q q q q q q q q q
TYP 1.3 1.7 0.4 5 0.2 3.2 20 7 1 5.7 5.5 5.3 5.0 0.2 0.2 0.2 35 1.4 1.4
MAX
UNITS V V V k V V mA mA A V V V V ms
10
0.5 10 50 0.8
2.0
mA A A V V
AC CHARACTERISTICS
PARAMETER Slew Rate Driver Propagation Delay (TTL to EIA / TIA-562) Receiver Propagation Delay (EIA / TIA-562 to TTL)
The q denotes specifications which apply over the operating temperature range 0C TA 70C. Note 1: Absolute maximum ratings are those values beyond which the life of the device may be impaired. Note 2: Supply current is measured with driver and receiver outputs unloaded.
Note 3: Measurements made in the Driver Disable mode are performed with VDRIVER DISABLE = GND and VON/OFF = VCC. Note 4: Measurements made in the Shutdown mode are performed with VON/OFF = 0V.
3 2 1 0 1 2 3 4 5 0 10
VTH+
40 30 20 50 TEMPERATURE (C)
2 DRIVERS LOADED RL = 3k
1 DRIVER LOADED RL = 3k
20 30 50 40 TEMPERATURE (C)
LTC1385 TPC04
LTC1385 TPC06
U W
60
LTC1385 TPC01
15
10
70
LTC1385 TPC02
LTC1385 TPC03
ISC
ISC+
60
70
10
30 20 40 50 TEMPERATURE (C)
10
50 30 40 20 TEMPERATURE (C)
60
70
LTC1385 TPC05
LTC1385 TPC06
INPUT INPUT
LTC1385 TPC08 LTC1385 TPC09
LTC1385
PI FU CTIO S
VCC: 3.3V Input Supply Pin. This pin should be decoupled with a 0.1F ceramic capacitor. GND: Ground Pin. ON/OFF: TTL/CMOS Compatible Shutdown Pin. A logic low puts the device in the Shutdown mode independent of the Driver Disable pin. The supply current drops to 0.2A and all driver and receiver outputs are forced into three-state. DRIVER DISABLE: TTL/CMOS Compatible Input Pin. With the ON/OFF pin held high, a logic low forces the part into the Driver Disable mode with the charge pump turned off and the driver outputs forced into three-state. Both receivers remain active and the supply current drops to 35A. A logic high forces the part into the Normal mode. V +: Positive Supply Output (EIA/TIA-562 Drivers). V + 2VCC 1V. This pin requires an external capacitor C = 0.1F for charge storage. The capacitor may be tied to ground or VCC. With multiple devices, the V + and V pins may share a common capacitor. For a large number of devices, increasing the size of the shared common storage capacitors is recommended to reduce ripple. V : Negative Supply Output (EIA/TIA-562 Drivers). V (2VCC 1.3V). This pin requires an external capacitor C = 0.1F for charge storage. C1+, C1, C2+, C2 : Commutating Capacitor Inputs. These pins require two external capacitors C = 0.1F: one from C1+ to C1, and another from C2+ to C2. To maintain charge pump efficiency, the capacitors effective series resistance should be less than 2. TR IN: EIA/TIA-562 Driver Input Pins. Inputs are TTL/ CMOS compatible. The inputs of unused drivers can be left unconnected since 300k input pull-up resistors to VCC are included on chip. To minimize power consumption, the internal driver pull-up resistors are disconnected from VCC in the Shutdown mode. TR OUT: Driver Outputs at EIA/TIA-562 Voltage Levels. Outputs are in a high impedance state when in the Shutdown or Driver Disable mode or VCC = 0V. The driver outputs are protected against ESD to 10kV for human body model discharges. RX IN: Receiver Inputs. These pins can be forced to 25V without damage. The receiver inputs are protected against ESD to 10kV for human body model discharges. Each receiver provides 0.4V of hysteresis for noise immunity. RX OUT: Receiver Outputs with TTL/CMOS Voltage Levels. Outputs are in a high impedance state when in the Shutdown mode.
SWITCHI G TI E WAVEFOR S
DRIVER INPUT DRIVER OUTPUT t LHD VCC 1.4V 1.4V 0V V+ 0V t HLD
1385 F01
1.7V
0V V
DRIVER INPUT
1385 F04
1385 F03
VCC
0.1F
16
LTC1385
PACKAGE DESCRIPTION U
Dimensions in inches (millimeters) unless otherwise noted. G Package 20-Lead SSOP
0.278 0.289* (7.07 7.33) 20 19 18 17 16 15 14 13 12 11
0.045 (1.14)
1 2 3 4 5 6 7 8 9 10 0.205 0.212* (5.20 5.38) 0.045 (1.14) 0.068 0.078 (1.73 1.99)
0 8
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm).
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
LTC1385
PACKAGE DESCRIPTION
NOTE: 1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS. 2. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm).
Dimensions in inches (millimeters) unless otherwise noted. S Package 18-Lead Plastic SOL
0.447 0.463 (11.354 11.760) (NOTE 2) 18 17 16 15 14 13 12 11 10
SEE NOTE