Ningbo YP 970

DAVID RR
NINGBO DAVID
OPERATOR
OPERATORS MANUAL
970
YP-970
YPINFANT INCUBATOR
Please take well care of it.
SPECIAL STATEMENT
STATEMENT:: All of the content in the manual is checked carefully, if there is
any error or content of printing misunderstanding, our company
retains finally explanation of this card-usage.
NOTE: The product
products appearances maybe differ from the one in this manual, but it dose
not affect the capability of product. Please understand if it brings you troubles.
NINGBO DAVID MEDICAL DEVICE CO., LTD.

ADD:
NO.
35,
JINXING
ROAD,
BINHAI
INDUSTRIAL
PARK,
XIANGSHAN
ECONOMIC
DEVELOPMENT ZONE, NINGBO, ZHEJIANG PROVINCE, P.R.CHINA

12
POST CODE: 3157
315712
FAX: 0086-574-65962111
MARKETING CENTER: NO. 100

00,, JINGHUA ROAD
ROAD,, HI-TECH INDUSTRIAL DEVELOPMENT ZONE,
NINGBO, CHINA
00
POST CODE: 3150
315000
TEL: 0086-574-87800008, 87800009
E-MAIL: sales@chinadavid.cn
FAX: 0086-574-87801111
sales@nbdavid.com
WEBSITE: http://www.nbdavid.com
EUROPEAN REPRESENTATIVE: SHANGHAI INTERNATIONAL HOLDING CORP. GMBH (EUROPE)
ADD: EIFFESTRASSE 80, 20537 HAMBURG, GERMANY
TEL: 0049-40-2513175
FAX: 0049-40-255726
EDITION/REVISION C/0
Guidance and manufacture

manufactures declaration electromagnetic emissionsfor all EQUIPMENT and SYSTEMS

manufactures declaration electromagnetic emission
The YP-970 Infant Incubator is intended for use in the electromagnetic environment specified below. The customer of
the user of the YP-970 Infant Incubator should assure that it is used in such and environment.
Emission test
Compliance
RF emissions
CISPR 11
Electromagnetic environment guidance

The YP-970 Infant Incubator uses RF energy only
Group 1
for
its
internal
function.
Therefore,
its
RF
emissions are very low and are not likely to cause

any interference in nearby electronic equipment.
RF emission
CISPR 11
Harmonic emissions
IEC 61000-3-2
Class B
Class A
establishments, including domestic establishments and

those directly connected to the public low-voltage
power supply network that supplies buildings used for
domestic purposes.
Voltage fluctuations/
flicker emissions
The YP-970 Infant Incubator is suitable for use in all
Complies
IEC 61000-3-3
Page 1 of 4

manufactures declaration electromagnetic immunity
for all EQUIPMENT and SYSTEMS

The YP-970 Infant Incubator is intended for use in the electromagnetic environment specified below. The customer or
the user of YP-970 Infant Incubator should assure that it is used in such an environment.
Immunity test
IEC 60601 test level
Compliance level
Electromagnetic environment
- guidance
Electrostatic
6 kV contact
6 kV contact
Floors should be wood, concrete
discharge (ESD)
8 kV air
8 kV air
or ceramic tile. If floor are
IEC 61000-4-2
covered with synthetic material,

the relative humidity should be
at least 30%.
Electrical fast
2 kV for power supply
2kV for power
Mains power quality should be
transient/burst
lines
supply lines
that of a typical commercial or
IEC 61000-4-4
hospital environment.
Surge
1 kV differential mode
1 kV differential
IEC 61000-4-5
2 kV common mode
mode
2 kV common mode
hospital environment.
Voltage dips, short
<5% UT
<5% UT
interruptions and
(>95% dip in UT)
(>95% dip in UT)
voltage variations on
for 0.5 cycle
for 0.5 cycle
hospital environment. If the user

of the YP-970 Infant Incubator
power supply input

lines
40% UT
40% UT
requires
continued
operation
IEC 61000-4-11
(60% dip in UT)
(60% dip in UT)
during
for 5 cycles
for 5 cycles
interruptions, it is recommended
power
mains
that the YP-970 Infant Incubator
NOTE
70% UT
70% UT
be
(30% dip in UT)
(30% dip in UT)
uninterruptible power supply or
for 25 cycles
for 25 cycles
a battery.
<5% UT
<5% UT
(>95% dip in UT)
(>95% dip in UT)
for 5 sec
for 5 sec
UT is the a.c. mains voltage prior to application of the test level.
Page 2 of 4
powered
from
an

for EQUIPMENT and SYSTEMS that are LIFE-SUPPORTING

The YP-970 Infant Incubator is intended for use in the electromagnetic environment specified below. The customer or
the user of YP-970 Infant Incubator should assure that it is used in such an environment.
Immunity test
IEC 60601 test level
Compliance
level
Electromagnetic environment - guidance

Portable and mobile RF communications equipment
should be used no closer to any part of the YP-970
Infant Incubator, including cables, than the
recommended separation distance calculated from
the equation applicable to the frequency of the
transmitter.
Recommended separation distance
Conducted RF
3Vrms
IEC 61000-4-6
150 kHz to 80 MHz
3 Vrms
3.5
d = P
V1
outside ISM bands a
10 Vrms
10 Vrms
150 kHz to 80 MHz

in ISM bands
Radiated RF
10 V/m
IEC 61000-4-3
80 MHz to 2.5 GHz
10 V/m
80 MHz to 800 MHz
800 MHz to 2.5 GHz

Where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter
manufacturer and d is the recommended separation
distance in metres (m). b
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey,c
should be less than the compliance level in each
frequency range.d
Interference may occur in the vicinity of equipment
marked with the following symbol:
NOTE 1
At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2
These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
a
The ISM(industrial, scientific and medical) bands between 150kHz and 80MHz are 6.765MHz to 6.795MHz; 13.553
MHz to 14.567 MHz; 26.957 MHz to 27.283 MHz; and 40.66 MHz to 40.70 MHz.
b
The compliance levels in the ISM frequency bands between 150kHz and 80MHz and in the frequency range 80 MHz
to 2.5GHz are intended to decrease the likelihood that mobile/portable communications equipment could cause
interference if it is inadvertently brought into patient areas. For this reason, an additional factor of 10/3 is used in
calculating the recommended separation distance for transmitters in these frequency ranges.
c
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile
radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with
accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey
should be considered. If the measured field strength in the location in which the YP-970 Infant Incubator is used
exceeds the applicable RF compliance level above, the YP-970 Infant Incubator should be observed to verify normal
operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or
relocating the YP-970 Infant Incubator.
d
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 10 V/m.
Page 3 of 4
Recommended separation distances between portable and mobile

RF communications equipment and the EQUIPMENT or SYSTEM
for EQUIPMENT or SYSTEM that are LIFE-SUPPORTING
Recommended separation distances between
portable and mobile RF communications equipment and the YP-970 Infant Incubator
The YP-970 Infant Incubator is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the YP-970 Infant Incubator can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications
equipment (transmitters) and the YP-970 Infant Incubator as recommended below, according to the maximum output
power of the communications equipment.
Separation distance according to frequency of transmitter
Rated
(m)
maximum
150 kHz to 80 MHz
150 kHz to 80 MHz
80 MHz to 800
output power
outside ISM bands
in ISM bands
MHz
of transmitter
800 MHz to 2.5 GHz
(W)
3.5
d = P
V1
0.01
0.1167
0.12
0.12
0.23
0.1
0.3689
0.3795
0.3795
0.7273
1.1667
1.2
1.2
2.3
10
3.6893
3.7947
3.7947
7.2732
100
11.6667
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in
metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the
maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1
At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2
The ISM(industrial, scientific and medical) bands between 150kHz and 80MHz are 6.765MHz to
6.795MHz; 13.553 MHz to 14.567 MHz; 26.957 MHz to 27.283 MHz; and 40.66 MHz to 40.70 MHz.
NoTE 3 An additional factor of 10/3 is used in calculating the recommended separation distance for transmitters in
the ISM frequency bands between 150kHz and 80 MHz and in the frequency range 80 MHz to 2.5 GHz to decrease
the likelihood that mobile/portable communications equipment could couse interference if it is inadvertently brought
into patient areas.
NOTE 4 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.
Page 4 of 4
OPERATORS MANUAL FOR INFANT INCUBATOR
WARRANTY
The product being described in this manual is warranted against defects in materials or
workmanship for one year from the date of shipment, with the following exceptions.
1. All consumable and disposable products are guaranteed to be free from defects upon
shipment only.
2. Calibrations are considered normal maintenance and are not included in the 1-year
warranty.
During the warranty period any defective parts other than those listed above will be replaced
at no charge to the customer.
This warranty is rendered void and our company cannot be held liable for conditions resultant
therefrom if:
1. Damage to the unit is incurred as a result of mishandling.
2. The customer fails to maintain the unit in a proper manner.
3. The customer uses any parts, accessories, or fittings not specified or sold by our company.
4. Sale or service is performed by the non-certified service/dealer agency.
This warranty is in lieu of all other warranties, expressed or implied, and our company shall in
no event be liable for incidental or consequential damages including loss of use, property damage,
or personal injury resulting from breach of warranty.
The Accreditation Manual for Hospitals requires each piece of equipment to be tested prior to
initial use and at least annually thereafter. To comply with this standard, we recommend that you
participate in our accreditation Testing compliance Program during the warranty period. This
service can be performed through our company and authorized dealers.
SERVICE
For optimal performance, product service should be performed only by authorized and
qualified service personnel. Please contact the local agency or the After-Sales of our company to
get more technical information about maintenance.
I4
OPERATING PRECAUTIONS
1. INFANT INCUBATOR (incubator) belongs to high risk medical device which can endanger
infant's life. Therefore please use the device only in neonate nursing room, children nursing
room, pediatric intensive care unit or similar sickroom in hospital. Operator for the device should
be special trained and operate the device under the instruction of medical practitioner.
2. The operator must keep observing the patient's condition while the device is working. Supervise
and record baby's temperature regularly to check whether the temperature of the patient is over
high/low or any other unusual conditions happen.
3. Please stop using the device when it failure or disfunction. Turn off the power and tansfer the
patient out from the device, then inform our company or our authorized agency for service. DO
NOT ask for service from person who's not been authorized by our company.
4. Direct radiation from sunlight or other infrared source could cause overheating of the infant
without activating the Over Temperature Alarm. DO NOT leave the INCUBATOR in direct
sunlight or near other sources of radiant heat.
5. DO NOT leave the INCUBATOR in the presence of flammable anaesthetic gases or other
flammable materials, such as some types of cleaning fluids.
6. DO NOT leave the INCUBATOR in the presence of strong electromagnetic field.
7. Devices which are easily interfered by magnetic field should not be used near the INCUBATOR
because they may interfered by the INCUBATOR.
8. The incubator does not equip the air cleaner, to make sure the good air quality inside hood, the
incubator should be used in the environment with clean air.
9. Please DO NOT use the INCUBATOR under working environment not stipulated in table 1.1, or
else, it may cause the failure or the INCUBATOR can not reach the requirements.
10. To prevent harm to the infant, the hood should not be raised while leads are connected to the
infant or if the mattress tilted.
11. There should be no need to raise the hood at any time while the infant is cared for in the
incubator. All necessary access to the infant can be achieved by means of the Access Panel and
Access Doors.
12. When the Access Panel is open, the temperature from the air temperature indicator maybe not
the real temperature inside incubator. Therefore, do not leave the Access Panel open much
longer.
13. All access panels latch should be firm plugged, in case accidental open.
14. For infant safety, DO NOT leave the infant unattended when the Access Panel is open.
15. Other accessories within the incubator which can alter the air flow pattern may affect
temperature uniformity and temperature variability.
16. Turning on Phototherapy unit may affect hood wall temperature, incubator air temperature and
infant skin temperature, at this time, we suggest the incubator should be worked in the baby
mode, otherwise the set air temperature of the thermotherapy devices has to be reduced
according to body temperature measurement.
ii
I4
17. Patient safety and incubator performance may be compromised if air flow passages are not
kept clear of obstructions (blankets, stuffed animals, etc.) during clinical usage.
18. Do not place surgical covers or blankets over the infant and warm air curtain or side vents
simultaneously. This may cause heat induced injury and burns.
19. Removing the incubator should be finished at least by two persons with great strength. Please
pull out all power cords before moving.
20. To prevent the harm on patient for accidental moving, please lock the casters during usage.
21. To prevent accidental disconnection, secure all patient leads, infusion lines and ventilator
tubing to the mattress with sufficient excess length to allow for the full range of mattress
height adjustment.
22. To avoid water over flow from water chamber, and keeping the most stable position of infant
incubator, before moving all of accessories should be fixed to the right position and let out all
of the water.
23. Do not switch on for longer time than essential, when the machine not connect to the power
supply, otherwise, power supply failure alarm will be actively and the internal battery current
waste.
24. When using X-Ray tray via incubator hood, the shadow of hood will reflect on the X-ray
negative. That maybe influence the doctors diagnose.
25. Do not place any article higher than incubators caster under its VHA cabinet which may affect
the stabilization of VHA cabinet.
26. When operating the VHA cabinet, support the incubator with one hand on to prevent it from
unbalance.
27. When replacing the fuse, you must cut off the power supply and replace it according to the
stipulated specification.
28. The device must be fully cleaned and sterilized for the first time for initial use, after nursing for
one baby, after used it for one week or there's dirt in the incubator. Cleaning and sterilizing
methods please refer to Section 5.
29. Please use the neutral deterge/ disinfectant registered by nation. Other disinfectant (like
alcohol) will destroy some parts of the incubator. Please follow the instruction for detergent
usage.
30. The customer uses any parts, accessories, or fittings only specified or sold by our company, or
else, it will reduce the safety of device.
31. Damages will be easily caused if using the incubator after it reached its lifetime. Previous
capability guideline and requirement cannot be reached as well.
32. The device, accessories and the packaging have to be disposed of waste correctly at the end
of the usage. Please follow Local Ordinances or Regulations for disposal.
I4
iii
ELECTRICAL PRECAUTIONS
1. To ensure grounding reliability, connect the ac power cord only to a properly grounded 3-wire
hospital grade or hospital use outlet. Do not use extension cords. If any doubt exists as to the
grounding connection, do not operate the equipment.
2. An electric shock hazard exists within the Controller and VHA base assembly when the cover is
removed. Servicing should be performed only by qualified personnel with appropriate service
documentation.
3. To prevent equipment damage or accidental power disconnection, Do NOT connect an
Incubator power cord directly to an ac wall socket when the Incubator is mounted on a VHA
stand. Always provide power to the Incubator using the power cord coming directly form the
VHA stand.
4. Make sure the building power source is compatible with the electrical specifications shown on
the rear center column of the VHA stand or on the Incubator.
5. This device adopts mains plug or appliance coupler as isolation form the supply mains when the
Incubator is mounted on a mobile stand, for safety, and please pull off the power cord when
stopping using the device or repair it.
6. Improbably using of the assistant device will cause the decrease of our devices safety. The
safety of auxiliary devices shall comply with the general requirements for safety according to
IEC601-1, and have acquired the certificate by relative institution.
HUMIDITY PRECAUTIONS
1. The incubator is with the humidity controller, it can increase the Humidity of incubator according
to the clinical demands.
2. Higher relative humidity will, at any given time, decrease an infants evaporative water loss and
may cause an increase in infant temperature. Monitor the infants temperature as required.
3. Use only distilled water to fill or refill the Reservoir. Tap water may contain organisms that may
flourish in the heated water of the humidifier.
4. Make sure all hood access door gaskets and tubing ports are properly installed. Any open gaps
in the incubator hood will reduce the incubators internal relative humidity.
5. Fill the humidity chamber to the bottom of the MAXIUM LIMIT line. DO NOT OVERFILL. Or else
water spillage may result.
6. Following the doctors advice when setting the relative humidity.
iv
I4
OXYGEN PRECAUTIONS
1. This incubator is with oxygen control system, please use iatric oxygen when feeding oxygen.
2. Abusing of supplemental oxygen may result in serious aftereffects which include blindness,
brain damage, even death. Therefore, keeping to the main doctor's direction strictly and
monitoring the oxygen supplement condition for the patient in a regularly time.
3. If it is necessary to administer Oxygen in an emergency, notify the attending physician
immediately.
4. When supplementing the oxygen, calibrated oxygen analyzer must be turned on for monitoring
the oxygen concentration.
5. Oxygen feeding may increase the noise level inside the hood.
6. As Oxygen use increases the danger of fire. To ensure the device safety, make all flammable
material far away from incubator, and auxiliary equipment producing sparks should not be
placed near incubator.
7. When the oil, grease, other fat substance and the compressed oxygen meet, it will self-ignite
seriously, therefore, try to avoid the oxygen pressure reducing valve/adjustment valve, valve for
oxygen cylinder, pipe, connector containing these substance.
8. Do not use combustible material like aether, alcohol etc. because once even a little aether,
alcohol, or other combustible material mixed with oxygen in the incubator, itll cause fire.
9. When modulating the oxygen flux every time, please leave 30min. at least for the incubator
regaining the new oxygen concentration.
10. Theres a pressurize device filling with potassium hydroxide electrolyte installed inside the
oxygen sensor. If the sensor leaks, please stop using and chuck it. If the leaking electrolyte
touches skin or clothes, please wash with clean water immediately. If the leaking electrolyte
touches eyes, please wash eyes with clean water for 15 min. and keep them open, notify the
doctor immediately.
11. Seasonal check the gas and the oxygen transporting parts to see if they are eroded or broken.
12. Seasonal check the battery of oxygen sensor to if they are leaking or aging. Replace them if it
is necessary.
13. A little flammable material left inside of hood will meet oxygen and cause fire, such as aether or
alcohol.
14. Please refer to the relevant user's manual when the auxiliary oxygen device is used together
with the incubator.
I4
WEIGHING PRECAUTIONS
1. The electrical scale installed in the bassinet must work after 30 minutes warm-up in the
incubator, that is to say the electrical scale cant work until being put in the incubator which is
set the using temperature and begins working for at least 30min. Or else, the number read on
the scale will surpass the regulated value.
2. Please keep the patient aclinic and in the middle of the bassinet while weighing.
3. The maximum weighing weight of Infant scale is 8 kg, please dont over loading, or else the
scale will be damaged.
4. Lay the bassinet with infant scale gently when loading or unloading, dont press surface of the
bassinet to avoid damage the weight sensor inside the bassinet.
5. The displayed weighing value is just for reference.
SEASONAL SAFETY CHECK

1. Please clean the plug of power cord at least once a year. Too much dust on plug may cause the
fire.
2. The following safety checks should be performed at least every 12 months by a qualified person
who has adequate training, knowledge, and practical experience to perform these tests. The data
should be recorded in an equipment log.
1 . Inspect the equipment and accessories for mechanical and functional damage.
2 . Inspect the safety relevant labels for legibility.
3 . Inspect the fuse to verify compliance with rated current and breaking characteristics.
4 . Verify that the device functions properly as described in the instructions for use.
5 . Test the protection earth resistance according IEC 60601-1:1988 + A1:1991 + A2:1995:
Limit 0.1.
6 . Test the earth leakage current according IEC 60601-1:1988 + A1:1991 + A2:1995: Limit:
NC 500A, SFC: 1000A.

7 . Test the enclosure leakage current according to IEC 60601-1:1988 + A1:1991 + A2:1995:
Limit: NC 100A, SFC: 500A.

8 . Test the patient leakage current according IEC 60601-1:1988 + A1:1991 + A2:1995: Limit:
for a.c.: 100A (BF), for d.c.: 10A (BF).

9 . Test the patient leakage current under single fault condition with mains voltage on the
applied part according IEC 60601-1:1988 + A1:1991 + A2:1995: Limit: for a.c.:500A (BF), for d.c.:
50A (BF).
10 . According to the test methods of IEC 60601-1:1988 + A1:1991 + A2:1995, the patient
leakage current (net voltage should be added on the applied part) of the testing device must less
than 5000A.
11 . Test the patient auxiliary leakage current according IEC 60601-1:1988 + A1:1991+
A2:1995: Limit: NC for a.c.: 100A (BF), for d.c.: 10A (BF).SFC 500A (BF), for d.c.: 50A (BF).
vi
I4
TABLE OF DEFINITIONS AND SYMBOLS

TECHNICAL DEFINITIONS
SKIN TEMPERATURE SENSOR: A sensing device including the link with the equipment intended
to measure the infants skin temperature.
INCUBATOR TEMPERATURE: Air temperature at a point 10cm above and centered over the
mattress surface.
CONTROL TEMPERATURE: The temperature set at the temperature control.
AVERAGE INCUBATOR TEMPERATURE
TEMPERATURE:: The average of the maximum and minimum Incubator
temperatures achieved during Temperature Condition.
STEADY TEMPERATURE CONDITION: A condition which is reached when the temperature does
not vary by more than 1 over a period of 1 hour.
MPERATURE ALARM CHECKOUT STATE: The difference between real temperature and
TEMPERATURE
TE
control temperature is within 0.5 and such state lasts for over 10 minutes. The equipment must
stay in such state when check up the alarm about temperature
TEMPERATURE UNIFORMITY
UNIFORMITY:: The amount by which the average temperature at each of four
points 10cm above the mattress surface differs from the Average incubator Temperature at steady
Temperature Condition. The four points are the centers of four quadrants formed by lines that
divide the width and length of the mattress surface.
VARIABILITY:: The variability of the Incubator Temperature that will be observed
TEMPERATURE VARIABILITY
over a one hour period after Incubator Temperature Equilibrium has been reached.
TEMPERATURE RISING TIME
TIME:: The time required for the Incubator Temperature to rise 11 ,
when the Air Control Temperature is at least 12 above ambient.
STEADY HUMIDITY CONDITION: A condition that the disparity between the indicated humidity
value and control value is less than 5%RH, and maintains over 2 min.
NOTE
NOTE,, IMPORTANT, CAUTION AND WARNING
NOTE: A note is inserted in text to point out procedures or conditions, which may otherwise be
misinterpreted or overlooked. A note may also be used to clarify apparently contradictory or
confusing situations.
IMPORTANT
IMPORTANT:: Similar to a Note but be used where greater emphasis is required.
CAUTION: A caution is inserted in text to call attention of a procedure which, It not followed
exactly, can lead to damage or destruction of the equipment.
WARNING: A warning is inserted in text to call attention to dangerous or hazardous conditions
inherent to the operation, cleaning, and maintenance of the equipment which may result in
personal Injury or death of the operator or patient.
I4
vii
SYMBOLS
CLASS I
Consult instructions for us
Protective Earth (Ground)
Class I Equipment
Type BF Applied Part
Main power on
Main power off
On (only for a part of equipment)
Off (only for a part of equipment)
AH/250V Fuse Type F 6.3AH/250V

F 6.3
6.3AH/250V
/50
Hz AC Power 220-230V, 50Hz
220-230V~
220-230V~/50
/50Hz
Weight Limit
RS
RS--232
O2
ON/OFF
>37
>37
CAL.
SN
High pressure, dangerous
RS-232 Connector
LOW
HIGH
Mattress Tilt Direction
Socket for skin temperature 1
Socket for skin temperature 2
High temperature warning
Heating Power Indicator
Oxygen supplement indication

mark
Humidifying indication mark
Indicator ON/OFF
SEL
Switch indicator key
Silence / Reset Key
Keypad Key
Set up key/raise devices height
Set down key/lower devices height
Air Mode Key
Baby Mode Key
37 setting key
ZERO
Reset zero key
Calibration key
CE Marking
Water high-level mark
Water low-level mark
Serial Number
Date Of Manufacture
Manufacturer
Authorised representative in the

european community
/50Hz MAX:1.6A
220-230V~
220-230V~/50Hz
Assistant net power outlet, MAX1.6A
viii
I4
CONTENTS
PAGE
SECTION
1. GENERAL INFORMATION
INFORMATION1-1
1.1 Introduction1-1
1.2 Intended use1-1
1.3 Composition of products1-1
1.4 Description1-1
1.5 Specifications1-3
2. INSTALLATION
INSTALLATION2-1
2.1 General2-1
2.2 Unpacking2-1
2.3 Installation2-1
DESCRIPTION3-1
3. FUNCTION DESCRIPTION
3.1 General function description3-1
3.2 Temperature control principle3-1
3.3 Data communication connector3-2
3.4 Alarming and system indication information3-3
OPERATION4-1
4. OPERATION
4.1 General4-1
4.2 Power supply connection and switch control4-1
4.3 Controller, indicators4-2
4.4 Operation checkout procedure4-5
4.5 General operation procedure4-14
5. CLEANING AND MAINTENANCE
MAINTENANCE5-1
5.1 General5-1
5.2 Cleaning5-1
5.3 Sterilization5-10
5.4 Maintenance5-10
5.5 Trouble shooting5-10
SYSTEM6-1
6. OXYGEN CONCENTRATION CONTROL SYSTEM
6.1 General6-1
6.2 Installation of oxygen sensor6-1
I4
ix
6.3 Function description6-2

6.4 Connection of oxygen input connector6-2
6.5 Operation and calibration procedures6-3
6.6 Using of oxygen supply system6-4
6.7 Maintenance6-5
SYSTEM7-1
7. HUMIDITY CONTROL SYSTEM
7.1 General7-1
7.4 Using of humidity control system7-2
7.5 Maintenance7-3
8. WEIGHING SYSTEM
SYSTEM8-1
8.1 General8-1
8.2 Installation8-1
8.5 Operation of weighing system8-2
8.6 Maintenance8-3
NOTE: The product composition maybe different from this manual, but it does not affect
product function. Please understand.
I4
SECTION 1
GENERAL INFORMATION
INTRODUCTION
1.1
1.1INTRODUCTION
This manual provides instructions for installation, debugging, operation, cleaning and
maintenance of Infant Incubator (incubator). We are not responsible for the malfunction which is
caused due to not following the instruction on our manual.
The operator should read and understand of the content of this manual.
This manual should be put together with the device so as to the client to check at any
moment.
VHA cabinit and weighing system are optional accessories. Besides, for air circulation fan
motor, user can choose either AC motor or DC motor. Disposable skin temperature sensor is also
provided as option. You can ignore the relative contents if you havent buy them. Neonate jaundice
phototherapy is optional assessory, if you buy it with the incubator, please refer to the operation
manual of Neonate jaundice phototherapy to see the relative operation.
E
1.2 INTENDED US
USE
The Infant Incubator is intended to provide a controlled thermal environment and isolation
from ambient air for premature and neonatal infants. The infant incubator is not intended for the
transport of infants.
3 COMPOSITION OF PRODUCTS
1.
1.3
The infant incubator consists of four components: the double wall hood, the base, the mobile
cabinet, and the controller. The sponge based mattress positions centrally within the confines of
the hood.
4 DESCRIPTION
1.
1.4
The following diagram shows the main parts of the Infant Incubator.
Neonate Bilirubin Phototherapy Equipment
I.V. Pole
Baby compartment
Shelf
Controller
Base
Mobile Cabinet
1-1
I4
DESCRIPTION OF PART
EXPLANATION
V. pole
I.
I.V
A kind of bearing part, which is used for hanging the infusion bottle.
Max. Load: 2Kg
Controller
The core part with two kinds of temperature control modes: air
mode, baby mode, moreover, it also have the function of weighing,
humidity control and oxygen concentration controling system which
are used for autocontrol the heat output and the huminidy and
oxygen concentration in the incubator. The detail operation to
temperature please refer to the section 4, to oxygen concentration
please refer to the section 6, to huminidy please refer to the section
7, to weighing please refers to the section 8.
Shelf
A kind of bearing part, which is used for putting some small objects.
Max. Load: 3.5Kg
Baby compartment
It is used for place the infant inside, including the Acrylic hood,
bassinet, and so on. The bassinet can be tilted at the request of
clinical needs. The baby scale is optional part, and the Max. Load
of bassinet is 10 Kg.
Max load of bassinet with weighting system is 8Kg.
Size of mattress: 630mm 355mm
Base
An important part of Infant Incubator, and it is mainly composed of

the Aluminium tank, humidity chamber, air filter, and so on.
Mobile Cabinet
A part which can support the main body of Infant Incubator. We

have two kinds of cabinet: fixed type and vertical height adjustment
type. Usually we equip the former one, and the second one is
optional part.
Neonate bilirubin
phototherapy
equipment
It is intended for treating the bilirubin of patient.

This part is mounted on top of Infant Incubator, and its light source
has two kinds: fluorescent lamp and LED lamp, the user can
choose this.
for the Neonate Bilirubin Phototherapy Equipment with fluorescent
lamp, please refer to the users manual XHZ-90, while for the
Neonate Bilirubin Phototherapy Equipment with LED lamp, please
refer to the users manual XHZ-90L.
The maximum bearing weight of shelf and other accessories is described in

the table. Please do not overload to avoid damages to accessories.
NOTE: Size of Infant Incubator:
mm
W650 H1560 D1440
1440mm
(for Infant Incubator with fixed cabinet);
mm ~ W650 H1640 D1440
mm
W650 H1500 D1440
1440mm
1440mm
(for Infant Incubator with vertical height adjustment cabinet).
Distance from the bassinet to the floor:
980mm (for Infant Incubator with fixed cabinet);
950mm ~ 1090mm (for Infant Incubator with vertical height adjustment cabinet).
Kg
Weight of Infant Incubator with fixed cabinet
cabinet:: 116
116Kg
Weight of Infant Incubator with vertical height adjustment cabinet: 126Kg
1-2
I4
1.5 SPECIFICATIONS
Specifications for the Infant Incubator are provided in table 1.1.
TABLE 1.1 SPECIFICATIONS

This equipment belongs to Class I, Type BF applied part, normal device (IP20) continuously
operated.
Power Requirements
equirements
AC220V-230V/50Hz, 1000VA
Maximum Heater Power Output

utput
377W/240V
Auxiliary Mains Power Output

Output
AC220V-230V/50Hz, MAX. CURRENT 1.6A
Heater power display

display
0 to 100%, adjustable in 10% increments
Temperature control modes

modes
Air mode
Baby mode
Air Temperature Control range

range
..
25~37
override mode: 37~39
..
Baby Temperature Control range

..
..
34~37
override mode: 37~38
Temperature sensor display range

range
5~65
Temperature rise Time* (environment temperature is +22
+22))
..
.. 30min
Temperature Variation*
Variation*
0.5
Temperature Uniformity* (level mattress
mattress))
0.8
Temperature Uniformity* (Tilt mattress)
1.0
Accuracy of skin temperature sensor

sensor
0.3
Deviation between the indicated air temperature and the real temperature
temperature
0.8
See table 3.1) Power failure alarm
ALARM(
ALARM(S
Fan motor alarm
Sensor failure alarm
High deviation alarm
Low deviation alarm
Over temperature alarm
The sensor box position alarm
Low Water alarm
Tank position alarm
System alarm
1-3
I4
continued

SPECIFICATIONS
continued
HUMIDITY CONTROLLING
Running time after the Reservoir filled by distilled water

water
Humidity<60%RH, 24h at least
.......
Reservoir
Reservoirs cubage
cubage
.......
.......
1600ml
..
..
Humidity display range

range
..
..
..
..
0%RH 99%RH Humidity
Control range
range
..
0%90%adjustable in 1% each time
ENVI TEM. 20
40
ENVI humidity 10%
90%
10%RH
Accuracy of humidity display
display
2040
40ENVI
10%90%
90%
NOTE: In the surrounding of high humidity, it may not control the humidity to a relatively low
level.
OXYGEN CONTROLLING
Oxygen display range

range
0%99%
Resolving power of Oxygen display

display
1%
Accuracy of oxygen display

display
3%
Oxygen setting range

range
20%60%adjustable in 1% each time
Life time of oxygen sensor

sensor
..
10000h MAX. with 100% oxygen
WEIGHING DISPLAY
Weight range
range
1008000g
Resolving power of weight display

display
1g
Accuracy of weight display

display
1%
ENVIRONMENT TEMP (Not to use in the environment exceed specified)
...
Operating Range
Range
...
...+20+30
..
Storage Range
Range
..
..
-20+55
ENVIRONMENT HUMIDITY
Operating Range
Range
.. 30%75%RH
Storage Range
Range
.. 93%RH
ATMOSPHERIC PRESSUR
Shipment and Store atmospheric pressure range

range
500hPa1060hPa
Operating atmospheric pressure range

range
700hPa1060hPa
AIR FLOW RATE
..
Ambient air movement rate
rate
..
..
..<0.3m/s
1-4
I4
continued

SPECIFICATIONS
continued
OTHER SPECIFICATION
equipped with AC motor)
Noise inside hood

hoodequipped
55dB(A)
[Ambient noise: 45dB(A)]
Noise inside hood
hood((equipped with DC motor
motor))Under the steady temperature condition 45dB(A)
under other conditions50dB(A)
[Ambient noise: 35dB(A)]
Carbon dioxide(CO2) concentration within the hood

hood
Less than 0.5% when a mixture
CO2 is delivered at 750ml/min at a point 10cm above the center of the mattress.
Air Flow rate above Mattress

Mattress
0.35m/s
SILENCE/RESET KEY
nce/Reset key to cancel the auditory alarm for 4min
If the following alarming active, press the Sile
Silence/Reset
(for oxygen sensor failure alarm and oxygen deviation alarm, this operation will stop the alarm for
110 seconds). If the failure is excluded, alarm will cancel after 4min/110sec. or press the
silence/reset twice to cancel the alarming directly. The system of the device comes back to the set
state.
Sensor failure Alarm
High Deviation alarm
Low Deviation alarm
Over temperature alarm
Fan motor alarm
The lifetime
8 years
(Lifetime means the period from sell-by date to the date of discarding as useless.))
* Refer to Table of Definitions and Symbols
NOTE: If opening the front Access Panel or Access door or using infant bed, supplies or
other equipment within incubator can alter the air flow pattern so as to affect the
temperature uniformity, temperature variability, the correlation of the incubator
temperature reading to center mattress temperature and skin temperature.
1-5
I4
SECTION 2
INSTALLATION
2.1 GENERAL
This section provides installing procedures about Infant Incubator.
2.2 UNPACKING
Generally, the Infant Incubator is usually packed to two cartons: main body and fixed cabinet
or Vertical Height Adjustment cabinet (VHA cabinet). When taking out the equipment from the
cartons, take care not to damage the spare parts of the Infant Incubator.
3 INSTALLATION
2.
2.3
At least two professionals are required to do the installation of the Infant Incubator with
spanners.
1. Install the main body onto the fixed cabinet or Vertical Height Adjustment cabinet
A. The installation of main body onto the fixed cabinet
a. As figure 2.1 indicates, put on the spring washer, flat washer on the casters, and then
connect with cabinet firmly. Note: The caster with brake must be installed in front of the cabinet.
FIGURE 2.1
b. As figure 2.2 indicates, lock the casters with brake, and put the guard rail and main body
on the cabinet, and then fix them with the lock mechanism on two sides of cabinet.
Main body of Incubator
Guard Rail
Lock
II
Cabinet
2-1
I4
(Enlarged figure I)
(Enlarged figure II)

2

1
Cabinet
wheel unlocked
wheel
locked
hang on the lock
close the lock spanner
NOTE: See Enlarged figure I, lock the casters as the arrow 1 indicates, and unlock the
casters as the arrow 2 indicates.
See Enlarged figure II, hang on the lock, and close the lock spanner.
IMPORTANT: Be careful not to install the guard rail in wrong direction, or else, the
controller can not be taken out. The front access panel and the cabinet door
should be in the same direction.
therefore, fixing the guard
bolt
The guard rail ensure grounding through bolt
railon the cabinet with bolts.
FIGURE 2.2
B. Install the main body onto the Vertical Height Adjustment Stand
a. The method of installlation casters is same as part A.
b. The method of installlation main body, guard rail on the Vertical Height Adjustment cabinet
samw as part A.
c. After installation, insert the power cord on the right side of Vertical Height Adjustment
cabinet into the power socket in figure 4.2.
Guard Rail
Power cord
Lock
Cabinet
FIGURE 2.3
2-2
I4
WARNING
WARNING:: Firm the main body onto the fixed cabinet or Vertical Height Adjustment
cabinet with lock mechanism. If not, it will cause the main body to deviate
from the fixed cabinet or Vertical Height Adjustment cabinet when the cabinet
tilts, especially when the hood is open.
2. Install the NEONATE BILIRUBIN PHOTOTHERAPY EQUIPMENT, I.V.Pole and shelf
A. Install the NEONATE BILIRUBIN PHOTOTHERAPY EQUIPMENT
Please refer to the method of installation for incubator mounted PHOTOTHERAPY unit
XHZ-90 and XHZ-90L in the accompanying documents.
B. Install I.V. Pole and shelf
1 Install the I.V. Pole beside the incubator as figure 2.4 indicates, and then adjust the hook
to a proper height, fix it with the turnbuckle.

Hexagon bolt
Infusion rod
Fixed seat
Step 1: loose the hexagon bolts on the fixed seat with spanner, insert the I.V. Pole to the bottom,
and fix the bolt to fasten the infusion rod.
Hook
for
infusion rod
Hexagon bolts
Turnbuckle
Step 2: Tight the hexagon bolts on the
Step 3: Rotate the hook into the I.V. Pole,
bottom of infusion rod to fix the rod.
and then tighten the hexagon bolts.
FIGURE 2.4
2 Install shelf
loose the hexagon bolts on the fixed seat as figure 2.5 indicatesinsert the fixed seat to the
infusion rod. Ensure the top of fixed seat is uniform with the position line on the infusion rod as
2-3
I4
enlarged figure A showes. Then tighten the hexagon bolts.

Enlarged figure A
Infusion rod
Position limit mark
A
Hexagon bolt
Fixed seat
When installing the shelf, the side with note label should face the front of incubator
incubator..
FIGURE 2.5
C. Install I.V. Pole and shelf without NEONATE BILIRUBIN PHOTOTHERAPY EQUIPMENT
equiped.
1 Install the I.V. Pole
Install the I.V. Pole beside the incubator as figure 2.6 indicates, and then adjust the I.V. Pole
to a proper height, fix it with the turnbuckle.
Hexagon bolt
Infusion rod
F ixed seat
Step 1: loose the hexagon bolts on the fixed seat with spanner, insert the I.V. Pole to the bottom,
and fix the bolt to fasten the infusion rod.
Hook of infusion rod
Turnbuckle
Hexagon bolt
Infusion rod
Step 2: Tight the hexagon bolts on the bottom
Step 3: Insert the hook of infusion rod into the
of infusion rod to fix the rod.
infusion rod, then tighten the turnbuckle

according to the direct as the arrow shows.
FIGURE 2.6
2 Install Shelf
loose the hexagon bolts on the fixed seat as figure 2.7 indicatesinsert the fixed seat to the
infusion rod. Ensure the top of fixed seat is uniform with the position limit mark on the infusion rod
2-4
I4
as enlarged figure A showes. Then tighten the hexagon bolts.
Enlarged figure A
Position limit mark
Shelf
A
Fixed seat
When installing the shelf, the side with note label should face the front of incubator
incubator..
FIGURE 2.7
3. Connect the sensor
Connect the sensor connector with sensor socket which is on the side of the incubators main
body as figure 2.8 directed. Then tighten the bolt in the connector.
Connection between the sensor connector and socket should in the right orientation
NOTE
NOTE
for these two parts have their own direction.
Fixed bolt
Sensor connector
FIGURE 2.8
4. Install oxygen sensor
Refer to the section 6 to see the detail.
5. Install weighing system
Refer to the section 8 to see the detail.
6. Insert the power cord
Insert the power cord into the socket of general power supply in figure 4.1 (for VHA cabinet);
Insert the power cord into the socket of general power supply in figure 4.2 (for fixed cabinet).
Check the INCUBATOR according to the instruction in section 4.4.
2-5
I4
SECTION 3
FUNCTIONAL DESCRIPTION
3.1 GENERAL FUNCTIONAL DESCRIPTION
Air Mode and Baby Mode
The Infant Incubator adopts temperature control system (Air
Mode),
humidity controlling system, oxygen concentration controlling system and weighing system (if it
is applicable).
Heat output control in Air Mode: it will control the heaters output automatically according
to the Air temperature sensor, see instruction in section 4.5.2.1;
Heat output control in Baby Mode: it will control the heaters output automatically
according to the Skin temperature sensor, see instruction in section 4.5.2.2.
Oxygen input control
controlAutocontrol the valve according to the oxygen concentration in the
incubator which detected by the oxygen concentration sensor. Please refer the section 6 to see
the details.
Reservoir humidifying output control Autocontrol the humidifier according to the
humidity in the incubator which detected by the humidity sensor. Please refer the section 7 to
see the details.
The set temperature, air temperature, skin temperature, oxygen concentration oxygen
setvalue, humidity value, humidity and weight (if it is applicable) can be indicated separately.
Except for the listed parts in section 1.4, the Infant Incubator also has 4pcs casters. (Two of
them with brakes)
3.2 TEMPERATURE CONTROL PRINCIPLE

The control of temperature, humidity and oxygen concentration inside hood is achieved by
means of the forced air circulation system as shown in Figure 3.1.
When the oxygen control function is locked, the outside air is filtered, it will flow through the
heater which can heat the air, and then the air enters into the hood through the inlet port under
the drive of fan motor, after then, it will be cycled back to the fan motor through the inlet port to
form the heat air cycle flow. And this heat air flow will come to the top of water tank and enter
into the hood with the vapor above the water.
When turning on the oxygen control function oxygen flow through the oxygen input
connector, then pass the electromagnetism valve and enters into the air-oxygen seprating
device through the oxygen input connector, after then, it enters into the heat air cycle flow under
the drive of the fan motor to supply the oxygen in the incubator.
3-1
I4
In addition, the air curtain outfited in the incubator will drive the air circle inside 1 flow
upwards and form a heat air circle flow at the access panel when the access panel of the hood is
open, thereby the temperature inside the hood will fall down.
Access panel close
Access door open
FIGURE 3.1
3 DATA COMMUNICATION CONNECTOR

3.
3.3
The incubator is equipped with RS-232 data communication connector and used for data
terminal output.
1. If connect the auxiliary device on this connector, this auxiliary device should be
proved by the corresponding national standard, moreover, the whole system should
accord with the corresponding IEC601-1 or the adjusted relative standard.
2. Everyone should be responsible for the safety requirement to the whole system. If
there is any question, please consult our after sale service department or local agent.
3-2
I4
3.4 ALARMING AND SYSTEM INDICATION INFORMATION

Refer to Table 3.1 listed alarm condition or process, the incubator will alarm.
TABLE 3.1 DETAILS OF ALARM MESSAGE

ALARM MESSAGE
DESCRIPTION
Power Failure Alarm
If the mains power supply fails or no power supply, the alarm with
audible and visual will active.
Box Position
Alarm
If the sensor box wrongly placed, the Alarm
Alarm light will flash with
continuous audible sound. At the same time, Message Indicator
.
displays Box Position
Position
Air Sensor
If the temperature sensor short-circuit, open-circuit or bad

Alarm
connected, the Alarm
Alarm light will flash with continuous audible
.
sound. At the same time, Message Indicator displays Air Sensor
Sensor
Isolated Sensor
If the isolated temperature sensor short-circuit, open-circuit or bad

Alarm
sound. At the same time, Message Indicator displays Isolated
Sensor
Sensor.
Temp Not Same
If the temperature difference deteceted between air temperature

Alarm
sensor and isolated temperature sensor over 0.8 the Alarm
Alarm
light will flash with continuous audible sound. At the same time,
.
Message Indicator displays Temp Not Same
Same
Airflow Sensor
If the air flow sensor short-circuit, open-circuit or bad connected, the

Alarm
Alarm
Alarm light will flash with continuous audible sound. At the same
.
time, Message Indicator displays Airflow Sensor
Sensor
Skin Sensor 1
In Baby Mode
Mode, If the skin sensor1 short-circuit, open-circuit or bad
Alarm
sound.
At the same time, Message Indicator displays Skin
Sensor 1.
Skin Sensor 1
Position
In Baby Mode
Mode, If thetemperature detected by skin sensor 1 always
Alarm
2 below the set temperature, the Alarm
.
displays Skin Sensor 1 Position
Position
Humidity Sensor
If the humidity sensor short-circuit, open-circuit or bad connected,

Alarm
the Alarm
Alarm light will flash with continuous audible sound. At the
.
same time, Message Indicator displays Humidity Sensor
Sensor
Oxygen Sensor 1
If the oxygen sensor1 short-circuit, open-circuit or bad connected,

Alarm
the Alarm
same time, Message Indicator displays Oxygen Sensor 1.
Oxygen Sensor 2
If the oxygen sensor2 short-circuit, open-circuit or bad connected,

Alarm
the Alarm
same time, Message Indicator displays Oxygen Sensor 2.
Oxygen Not Same
If the oxygen concentration difference deteceted between oxygen

Alarm
sensor1 and oxygen sensor2 over 3%O2, the Alarm
Alarm light will flash
with continuous audible sound. At the same time, Message
.
Same
Indicator displays Oxygen Not Same
3-3
I4
TABLE 3.1 DETAILS OF ALARM MESSAGE (continued)

ALARM MESSAGE
DESCRIPTION
Air Error
Alarm
Alarm
After the air circulate inner the device stop for a while, the Alarm
light will flash with continuous audible sound. At the same time,
Message Indicator displays Airflow Error
.
Error
Motor Error
Fan Error
When the fan motor stops working or its running too slow, the
Alarm
Alarm
Alarm light will flash with continuous audible sound. At the same
. (When it is not
time, Message Indicator displays Motor Error
Error
applied for configuration of DC motor)
Alarm
When the fan inside the sensor box failure, the Alarm
Alarm light will
flash with continuous audible sound. At the same time, Message
.
Indicator displays Fan Error
Error
In Air Mode
Mode, If the air temperature is 3 higher than the set
Alarm
temperature, the Alarm
.
sound. At the same time, Message Indicator displays High Temp
Temp
High Temp
In Baby Mode
Mode, If the temperature detected by skin sensor1 is
Alarm
1higher than the set temperature, the Alarm
.
displays High Temp
Temp
High Humidity
If the humidity detected by humidity sensor is higher than 15%RH,

Alarm
the Alarm
.
same time, Message Indicator displays High Humidity
Humidity
High Oxygen
If the oxygen concentration detected by oxygen sensor1 is higher

Alarm
than 5%O2, the Alarm
sound. At the same time, Message Indicator displays High
Oxygen.
Oxygen
In Air Mode
Mode, If the air temperature is 3 lower than the set
Alarm
temperature, the Alarm
.
sound. At the same time, Message Indicator displays Low Temp
Temp
Low Temp
In Baby Mode
Mode, If the temperature detected by skin sensor1 is
Alarm
1lower than the set temperature, the Alarm
.
displays Low Temp
Temp
Low Humidity
If the humidity detected by humidity sensor is lower than 15%RH,

Alarm
the Alarm
.
same time, Message Indicator displays Low Humidity
Humidity
Low Oxygen
If the oxygen concentration detected by oxygen sensor1 is lower

Alarm
than 5%O2, the Alarm
sound. At the same time, Message Indicator displays Low
Oxygen
Oxygen.
Ove
Overr Temp
In Air Mode
Mode, when the incubator temperature is less than 38(set
temperature 37) or less than 40 (set temperature 37),
Alarm
the Alarm
.
same time, Message Indicator displays Over Temp
Temp
In Baby Mode
Mode, when the incubator temperature is less than 40,
Alarm
the Alarm
.
same time, Message Indicator displays Over Temp
Temp
3-4
I4
TABLE 3.1 DETAILS OF ALARM MESSAGE (continued)

ALARM MESSAGE
DESCRIPTION
Low Water
Alarm
When the water in the water tank burned off, the Alarm
Alarm light will
flash with continuous audible sound. At the same time, Message
.
Indicator displays Low Water
Water
Tank Position
Alarm
When the water tank is not in the correct location, the Alarm
Alarm light
will flash with continuous audible sound. At the same time, Message
.
Indicator displays Tank Position
Position
System Alarm
System
When the internal system failure, the System
System light will flash with
continuous audible sound. And Message Indicator displays the
system alarm code. At the same time, please ask the qualified service
personnel to repair it.
NOTE: 1. If alarms active, the incubator will cut off the heater power supply
automatically. (Except low deviation alarm,oxygen concentration alarm and
humidity sensor alarm)
2. The class of system alarm is arranged according to the serial number of the
alarm code, the larger the serial number, the lower the class, when many failure
occur, the superior class will alarm first.
3-5
I4
SECTION 4
OPERATION
4.1 GENERAL
This section provides operation procedures for Infant Incubator.
4.2 POWER SUPPLY CONNECTION AND SWITCH CONTROL

See figure 4.1, for the infant incubator with VHA cabinet, general power socket and the
general power switch are located under the cabinet; See figure 4.2, for the infant cubator with fixed
cabinet, general Power supply socket and general power switch, auxiliary mains output socket are
located on the back of controller.
General power switch
General power socket
FIGURE 4.1
Data communication connector

Socket for skin temperature sensor
Power switch
Auxiliary mains output socket
(To phototherapy)
Power supply socket

FIGURE 4.2
See figure 4.3, for the infant incubator with VHA cabinet, the height adjustment foot button is
on the bottom of stand.
Down foot button

Up foot button
FIGURE 4.3
CAUTION: The vertical height adjustment Stand should be restarted after 30s.
I4
4-1
TORS
4.3 CONTROLLERS, INDICA
INDICAT
1
4 5
6 7
10
11
12 13
14 15 16
17
O2
>37
>37
18 19 20 21 22
23
24
25 26
27 28 29 30
31 32
FIGURE 4.4
1. Oxygen concentration indicator key
Press this key to turn on or off the oxygen concentration indicator and oxygen concentration
control system.
2. Humidity indicator key
Press this key to turn on or off the humidity indicator and humidity control system.
3. Oxygen concentration indicator
Turnning the oxygen concentration indicator on to observe current oxygen concentration
valuedetected by oxygen concentration sensor, turnning it off, it indicates OF.
4. Humidity indicator
Display the current humidity value detected by the humidity sensor when it is on when
ternning it off, it display OF.
5. Humidifying indicator light
This light on indicates the humidifying system is on working.
6. Humidity set indicator
When the humidity control is turned on, it displays the humidity value.
7. Oxygen concentration set indicator
When the oxygen concentration control is turned on, it displays the oxygen concentration
value.
8. Set temperature indicator
Indicates the control value of air temperature in Air Mode
Mode; indicate the control value of baby
temperature in Baby Mode
ode.
9. Air temperature indicator
Indicate air temperature.
4-2
I4
10. Keypad lock indicator

If this light is on, it means entering into the set state and all functional keys active; if the light is
off, it means the system is not in set state, and all keys are locked.
NOTE: Except for the Oxygen Concentration Indicator key, Humidity Indicator key, Zero
NOTE:
key, Calibration key and Switch Setting Indicator key
key.
11. Heater power indicator
Indicate the heater output proportion.
12. Baby mode indication light
This light is on when it is in Baby Mode
ode.
13. Battery condition indication light
It will show the condition of the electricity, and the yellow light means it is charging, while the
green one means it is full. The temperature control will check the condition of the battery during
incubator working and charge and discharge automatically.
14. 37 indicator
This light is on means the incubator is working under the state of 37, and the patient is in
the environment of high temperature.
15. Skin temperature indicator
Display the baby temperature detected by skin temperature sensor 1, press Baby Mode key
key, it display the baby temperature detected by skin temperature sensor 2.
and Set Up key
16. Message indicator
When the device normally working, it displaying the current time. When the device is alarming,
it displaying the alarm information.
17. System alarming indicator light
It shines when incubator inner system failure.
WARNING: Please stop operating immediately and repairing by qulified personnel
once this light shines.
18. Zero key
Press this key to reset the weight display on the indicatorthe reset range is 0~2000g.
19. Calibration key
This key is used only for calibrate the weigh sensordo not press in the normal operation.
20. Weight indicator
Display the weight tested by weighing sytem
21. Oxygen supplement indicating light
When the light of this indicator enlightened, the oxygen supplement system is on working.
I4
4-3
22. Switch setting indicator key

Press this key to select the setted value of temperature, humidity and oxygen concentrition
displayed in the indicator in turn.
23. Air mode key
In set state, press to come into Air Mode
Mode.
24. Air temperature mode indication light
This light is on when it is in Air Mode
ode.
25. Keypad lock
Press to active all functional keys.
NOTE: Except for the Oxygen Concentration Indicator key, Humidity Indicator key, Zero
(NOTE:
key, Calibration key and Switch Setting Indicator key
key.)
26. Baby mode key
In set state, pressing this key to enter into Baby Mode
Mode.
27. 37 key
When incubator works under the state of 37, in set state, press to make the control value
override 37 to set temperature.
37,, pressing this key does not work.
NOTE: Before setting temperature at 37
37,, the patient is in the environment of high
Under the state of 37
temperature, and the nurse should examine the patient carefully.
28. Power failure alarm indicating light
This light enlightening when the power failure alarm activies.
29. Silence /Reset key
When alarm actived, press it once to clear the auditory alarm, and press this key twice to clear
the alarm.
30. Alarm indicating light
When something wrong with the device, this light will be enlightened (except for system
alarm
31. Set down key
In set state, press this key to decrease the set temperature. Press this key constantly to
speed the decreasing temperature.
32. Set up key
In set state, press this key to increase the setting temperature. Press this key constantly to
speed the increasing temperature.
4-4
I4
4 OPERATION CHECKOUT PROCEDURE

4.
4.4
WARNING
1. Please stop using this model once some function losts or te spare parts for front access
panel is loose.
2. Set temperature must be high 3 than ambient temperature. And then you can proceed
this checkout procedure.
3. Please do not damage the VHA cabinet during moving. And lower the cabinet to the
lowest position before moving so that the incubator is stable
stable..
Incubator should be only operated by trained personnel which knows familiar about the
general risk of operating the incubator and under the instructions of medical practitioner.
Please do the following checkout procedure each time before operation.
4.4.1 CHECK THE INTEGRITY OF INCUBATOR
Make sure that the device has been sterilized;
Make sure that the hood are locked firmly;
Make sure that there is no crack or the sharp edge on the hood;
Make sure that the I.V.Pole and shelf are locked firmly;
Make sure that the tilt mechanism of bed can work properly ;
Make sure that the needed accessories and other devices are available;
Make sure that the power cord is connected and is safe.
Make sure that the casters are installed well.

Check whether the caster can drop when lifting the incubator 2cm above the ground. The
drop of the caster will cause danger during transporting.

4.4.2 CHECK CONTROLLER
NOTE: Make sure that the power supply is compatible with the electrical specifications
lapelled on the incubator, for proper grounding reliability, connect the power cord
only to properly grounded 3-wire hospital-grade or hospital-use outlet. Do not use
extension cords.
A. START-UP THE CONTROLLER
Under the condition of power supplying, turn on the main power switch (if it is applicable) and
the power switch of the controller. The controller will briefly sounds like Ding as well as the
information indicator displays system Test, that shows the controller is in the self-checking
mode which will last for 5sec. After the self-checking process finishing, the Set Temperature
indicator shines and displays the set temperature for latest time before the device is stop working,
the Keypad Lock indicator enlightened, Air Temperature indicator displays the real temperature
detected by the air sensor, the Skin Temperature indicator displays the real temperature detected
by the skin sensor1 and the Weight indicator displays the real weight detected by the weighing
sensor. If the indicator for humidity and oxygen concentration is off, it displays OF, if they are on
working, they display the real value detected by the humidity sensor and the oxygen sensor
separately, and Humidity Set indicator and Oxygen Concentration Set indicator display the
value. If something abnormal or the displayed numbers incomplete, the controller need to be
maintained.
I4
4-5
B. CHECK POWER FAILURE ALARM
Pull off the power cord of whole unit, the Power failure alarm should active, and the Power
Power
light will flash with continuous audible sound.
This operation is used for checking if the power failure is normal or not. Insert the power cord
again after finishing checking.
IMPORTANT: Make sure that the rechargeable battery is full before usage. If not full, it may
cause the power failure without the alarming indication. If full, and there is no
any indication after disconnecting the main power supply, please refer to the
qualified service personnel
personnel..
C. CHECK HEATER
Control the environment temperature at 21 ~ 26, and choose the Air Mode
Mode, and set the
temeprature at 33.0, and all heat power indicator are on, and heater wll output heat completely.
NOTE: When the incubator works under the set state, and continue the following operation
procedure.
D. CHECK THE ACCURACY OF TEMPERATURE CONTROL
Select the Air Mode
Mode, and set the air temperature at 36, after the air temperature enters into
the STEADY TEMPERATURE CONDITION
CONDITION, put the calibrated temperature measuring device on
the position above 10cm from the center of mattress to measure the air temperature, compared
with the indicated air temperature to check whether the deviation between them is within 0.8.
E. CHECK BABY MODE
Insert two skin temperature sensors into the socket of skin sensor1 and skin sensor2
sepratelythe arrow sign on the plug should aim to the opening on the sensor socket so that the
sensor is inserted correctly.
Skin temperature Sensor 1
Arrow
oxygen concentration sensor
Opening
Sensor plug
Humidity sensor and air temperature sensor are located in the position A
Insert or pull out the skin sensor, you must hold the plug of skin sensor,
1.
1.Insert
pulling the leads is forbidden.
Please do not bend the connection of sensor.
2.
2.Please
4-6
I4
When the Air Mode works stablly, change it into the Baby Mode
Mode, set temperature at 37.
Keep the temperature detected by skin temperature sensor is 2 lower than the set temperature
while making the displayed air temperature 4 lower than the set skin temperature. The sensor
Alarm
failure alarm should be actived then.The Alarm
Alarm light will flash with continuous audible sound,
Skin Sensor 1 Position
and the Message indicator will show Skin
Position.
Alarm
Pull off the skin temperature sensor1, the sensor failure alarm should active. The A
larm
Skin Sensor
light will flash with continuous audible sound, and the Message indicator will show Skin
1.
F. CHECK PRECISION OF SKIN TEMPERATURE SENSOR
Put the skin temperature sensor with the mercury thermograph for the accuracy with 0.1C
into the water cup with the temperature as 30C5C. Make the probe of the skin temperature
sensor and the mercury ball as closely as possible and stir enough, then read the value of mercury
thermograph. Compare the value of the skin temperature sensor and the mercury thermograph,
and the deviation must be within 0.5C.
NOTE: Please check again if the accuracy of the skin temperature sensor exceeds the
permissibility deviation. Please let the professional maintenance man service
machine if the accuracy the skin temperature sensor exceeds the permissibility of
deviation again.
G. CHECK THE SENSOR BOX
Check the connection between the modular and its socket. Only when the interface of the
sensor box is correctly facing the interface of the sensor socket, they can be successfully
connected.
STATOR
Undraw the left stator of sensor box as the arrow indicates; under the condition of stator
undrawing, undraw the sensor box outwards, to check if the Sensor box slides in or out of the
Alarm
hood smoothly. When the modular falls off from the hood, The Alarm
Box Position
continuous audible sound, and the Message indicator will show Box
Position. After the modular
being put into the correct location and being fixed by stator, the alarm cancels automaticly as well
as the sensor connect indicating light off.
I4
4-7
WARNING
WARNING:: 1. All gaps in the sensor module must not be blocked.
2. Please pull out and plug in the sensor module correctly.
3. Sensor Module is an important part which supply Temperature Control to
Incubator, and must operate carefully.
H. CHECK FAN MOTOR ALARM
Block the inlet port and outlet port on the left and right side of main deck, after several minutes,
Alarm
larm light will flash with continuous audible sound, and the
the device gives alarms, the A
Airflow Error
Message indicator will show Airflow
Error.
When the incubator is equiped with AC motor, turn off the power supply of controller, and pull
off the power cord, and take out the controller.Reconnect the power cord, and hold the fan slightly,
Alarm
and turn on the switch of controller, and the fan motor alarm occurs, the Alarm
Motor Error
continuous audible sound, and the Message indicator will show Motor
Error.
WARNING: 1. If the temperature of heater inside controller is too high, you can
remove the conteoller or touch the heater after the unit is switched
off at least 45min to avoid the burn.
2starting after taking out the controller, please pay attention to the
power plug of oxygen concentration and humidity control system
to avoid electrical shock.
ERATURE ALARM
I. CHECK OVER-TEMP
OVER-TEMPERATURE
In Air Mode
Mode, enter into the working state, press Up
Up, Down and Silence/Reset key
key, there is
no indication on the Set Temperature indicator, and the heat power indicator is on in full, and the
controller has entered into the overtemp checkout state, and when the incubator temperature is
Alarm
less than 38.0 , the over-temperature alarm should active. The Alarm
Over Temp
37
continuous audible sound, and the Message indicator will show Over
Temp. In the state of 37
Override Mode
Mode, enter into the working state, press Up
key, there is
no indication on the Set Temperature indicator, and the heat power indicator is on in full, and the
controller has entered into the overtemp checkout state, and when the incubator temperature is
Alarm
less than 40.0 , the over-temperature alarm should active. The Alarm
Over Temp
continuous audible sound, and the Message indicator will show Over
Temp.
Mode, press Up
key, there is no indication on the Set
In Baby Mode
Temperature indicator, and the heat power indicator is on in full, and the controller has entered
into the overtemp checkout state, and when the incubator temperature is less than 40.0, the
Alarm
over-temperature alarm should active. The Alarm
Over Temp
and the Message indicator will show Over
Temp.
4-8
I4
J.CHECK DEVIATION ALARM

In Air Mode
Mode, close all door and panelss, set the temperature at 32 C. Enter TEMPERATURE
STATErefer to descriptions of terms and symbols concerned, fan into the
ALARM CHECKOUT STATE
hot air inside the hood. When the air temperature indicates 35.1C, the high deviation alarm will
Alarm
active. The Alarm
Alarm light will flash with continuous audible sound, and the Message indicator will
High Temp
Temp; set the temperature at 35, after the device enters into the temperature
show High
alarming checkout state, open the front access panel, when the air temperature indicates 31.9 C,
Alarm
the low deviation alarm should active. The Alarm
Low Temp
Temp.
and the Message indicator will show Low
NOTE: If the system can not enter into the TEMPERATURE ALARM CHECKOUT STATE or
the air Temperature does vary wihtin 3 than the setting temperature, the
deviation alarm can not occur.
In Baby Mode
Mode, set the temperature at 35 C. Enter TEMPERATURE ALARM CHECKOUT
STATE
STATE, put the skin sensor into the water cup at 37 C. When the skin temperature indicates 36.1
Alarm
C, the high deviation alarm will active. The Alarm
High Temp
and the Message indicator will show High
Temp; Set the temperature at 35, after the device
enters into the temperature alarming checkout state, put the skin sensor into the water cup at
temperature 33, when theskin temperature indicates to 33.9C, the low deviation alarm should
Alarm
active. The Alarm
Alarm light will flash with continuous audible sound, and the Message indicator will
Low Temp
show Low
Temp.
NOTE: If the system can not enter into TEMPERATURE ALARM CHECKOUT STATE or the
skin temperature does vary within 1 than the setting temperature, the
deviation alarm can not occur.
K. CHECK THE WATER LACKING ALARM
When humidifying system is on working, pour out the water in the water tank. After a while, the
Alarm
incubator will alarm. The Alarm
Alarm light will flash with continuous audible sound, and the Message
Low Water
indicator will show Low
Water.
L. CHECK THE WATER TANK IN INCORRECT LACATION ALARM
When the incubator is in the working state, pulling out the water tank, the incubator will alarm.
Alarm
The Alarm
Alarm light will flash with continuous audible sound, and the Message indicator will show
Tank Position
Tank
Position.
M. CHECK THE TIMER
When the controller is normally working, the Message shall diaplays the current realtime. If
the displayed time is not correct, please reset the time. The seting method is as following:
I4
4-9
Pressing Air Mode key while put the power of the controller on for more than 3 seconds until
the set interface appears. At that time, the Set Temperature indicator displays the set code and
Air Temperature indicator displays the corresponding value of each set item (the set code, set
item and set range please refer to the following table), the Skin Temperature indicator displays
P002 (which means the system has entered into the time seting interface). The operator could
select the set items through pressing the Baby Mode key or the Air Mode key and set the item
value through pressing Up Key or Down Key
Key. After seting one item, press Keypad Lock key to
save the seted value as well as press Silence/Reset key after seting all items for exit the seting
interface. If put off the power directly without pressing Keypad Lock key or Silence/Reset key
after seting, the time set will failure this time, system keeps the previous set value.
Table of time seting items
Set Code
Indicating Items
Set Range
001
two front numbers of year
19 ~20
002
two back numbers of year
00 ~99
003
month
01 ~12
004
day
01 ~31
005
week
006
hour
00~23 (for 24hours)
007
minute
00~59
008
second
00~59
01~0701stand for sundaydeduced accordingly
4.4.3 MECHANICAL EXAMINATION

A. CHECK THE HOOD OPERATION
See the following figure, raise the hood until you hear the sound kata, and the hood is in the
lock state. Press the lock downward as the arrrow indicates so that the hood can return the original
position.
CAUTION: Before raise the hood, ensure all accessories are disconnected to avoid
interfere operating.
Oritention lock
4-10
I4
B. CHECK FRONT ACCESS PANEL

The Pawl Latch
LOCKED
The Latch Seat
UNLOCK
Rotate the panel Latches and make it stays opening. Press the latch seat to open the Access
Panel to the full open position (rotate downward). Close the Access Panel, the seat latch fastened
automatically and then rotate both latches until they are fully locked. Both latches and the seat
latch must be fully locked to avoid accidental opening of the panel.
C. CHECK IRIS ENTRY PORTS
Rotate the outer ring of each enrty Port, the port should be open and close as rotation is
continued through 360 degree.
D. CHECK THE LATCH AND GASKET OF ACCESS DOOR
Press on-off of each access door to open it automatically and check the seal of gaskets.
I4
4-11
E. CHECK THE INNER WALL

Back inner wall
Limit hole of back inner wall
bottom of the back inner wall in
should insert in the fixing bolt
frontaccess panel
Inner wall in front

access panel:
Open the front access panel slightly press the front access panel towards the arrow1 and
move follow the arrow 2 directs, the inner wall of the front access door should be taken out easily.
After replace the inner wall, dont take it out.
F. CHECK MATTRESS TILT MECHANISM
Rotate the mattress tilt mechanism to adjust it.

4-12
I4
G. CHECK BASSINET
Open the Access Panel and slide it out to the fully extended position indicated by the arrow.
Lean on Mattress Tray to make sure it is properly supported to provide a firm infant platform.
Return the mattress and close Access Panel.
H. CHECK THE AIR INTAKE FILTER
Loosen the two thumb screws of the Air Intake Filter Cover and remove the cover and inspect
the filter, if dirty, it should be cleaned. Put the filter cover back.
WARNING: A dirty Air Intake filter may affect oxygen concentration and /or cause Carbon
Dioxide build-up. The filter must be checked on a routine basis and changed
at least every two months.
I. CHECK THE HIGHT ADJUSTMENT OF THE CABINET

Step the Up and Down button with your feet in figure 4.3 to adjust the height of whole unit.
I4
4-13
4.5 GENERAL OPERATION PROCEDURE

WARNING
1. Please read this operator
operators manual carefully before use.
2. You should not use the incubator without the checkout procedure, and please refer
to the qualified person.
person.
3. For the incubator
incubators normal function, the setting temperature must 3 higher than
environment temperature.
4.5.1 PREPARATION
4.5.1.1 Connect the power supply cord, sensor modular and skin temperature sensor1 correctly.
4.5.1.2 Pre-warm the incubator, put the patient on the bassinet after the air temperature reaches
the stable temperature to avoid the body temperature of the patient decreasing in the
non-prewarm incubator. The specific prewarm method is as follows:
Choose Air Mode
Mode, and set a proper control temperature, and make the device continue
working until the air temperature reaches the control value.
IMPORTANT: Please ask the physician to decide the set temperature.
4.5.2 OPERATION
4.5.2.1 AIR MODE
Air Mode means the controller will control the incubator temperature automatically to keep the
air temperature close to set temperature.
Incubator temperature is monitored the sensor probe and compared with the set air
temperature. The result of comparing is passed to the heater control circuit to control the heat for
keeping the set air temperature. The isolated temperature sensor as backup can control the
maximum incubator temperature. If the temperature is over high, and the heat protective device
will active, and the heater is cut off.
Press the Keypad Lcok key to select the Air Mode
Mode. Set the remperature at the wanted one.
The air temperature will keep within the range of 0.2 compared the set temperature.
When the incubator is working, if need changing the set temperature (decrease or increase),
press the Keypad Lock key to enlighten its indicating light, choose the Air Mode key to adjust the
37
set temperature through pressing Up and Down Key
Key. Set 37
37 Override Mode
Mode, you need to
37
press the Up key until the air temperature indicates 37, press 37
37 key , and the device will
enter into the temperature override mode, and 37 indicator is on, press Up key to set. After
chose the proper temperature, press Keypad Lock key to enter into the control mode, or without
pressing any key for 10s, and the controller will enter into the control mode automatically. Set
Temperature indicator displays the set temperature, and Air Temperature indicator displays the
air temperature, and Skin Temperature indicator displays the baby temperature tested by skin
temperature sensor1 (If the sensor is connected).
4-14
I4
4.5.2.2 BABY MODE

Baby Mode is one temperature control method which means the controller will control the
incubator temperature automatically to keep the baby temperature close to set temperature.
There are two skin sensors equipped in the device, one is skin sensor 1 and the other is skin
sensor 2. Between which skin sensor1 works as the temperature controlling sensor, which makes
the controller controls the temperature according to its detected temperature; skin sensor 2 is for
the clinical requirement which used for the assistant observation for the infant temperature (the
detailed observation method for skin sensor 2 please refer to the section 4.3). The probe of Skin
temperature sensor 1 required closely attached to the skin of patient, and the information from
probe is passed to the heater control circuit to control the heat for keeping the set baby
temperature. The isolated temperature sensor as backup can control the maximum incubator
temperature. If the temperature is over high, and the heat protective deice will active, and the
heater is cut off.
When the incubator is working, if need changing the set temperature (decrease or increase),
key, choose the Baby Mode key to adjust the set temperature through
press the Keypad Lock key
37
pressing Up and Down Key
Key. Set 37
37 Override Mode
Mode, you need to press the Up key until the
37
key
baby temperature indicates 37, press 37
37key
key, and the device will enter into the temperature
override mode, and 37 indicator is on, press Up key to set . After chose the proper
temperature, press Keypad Lock key to enter into the control mode, or without pressing any key
for 10s, and the controller will enter into the control mode automatically. Set Temperature
indicator displays the set temperature, and Air Temperature indicator displays the air temperature,
and Skin Temperature indicator displays the baby temperature tested by skin temperature
sensor1.
For seting the appropriate temperature and correctly control the baby temperature of the
infant, the incubator hold the following functions:
When the temperature detected by the skin temperature sensor 1 is always below the set
temperature for more than 2, the incubator will rise the air temperature in the incubator in the
speed of 1 per hour to enable the slowly rising of the infants temperature and avoids the
damage bringed by the rapid rising of the temperature as well. If the baby temperature detected is
Skin Sensor 1 Position
always 2below the set temperature in 1 hour, Skin
Position alarm will be actived by
system. At that time, the incubator still rise the air temperature in the hood slowly until the air
temperature reaches the STEADY TEMPERATURE CONDITION which its temperature is equal
to set skin temperatur -4. For example, in Baby Mode
Mode, if the set temperature is 36.5, finally
the air temperature in the incubator will reach the STEADY TEMPERATURE CONDITION
which
its temperature is 32.5.

For avoiding the incubator unnecessarily decreases its temperature for the reason of infant
pyrexia or something else, the incubator holds the following functions:
If the baby skin temperature surpasses the set temperature for less than 0.5, the air
temperature in the incubator will not lower 5 than the baby skin temperature. If the baby skin
temperature surpasses the set temperature for over than 0.5, the air temperature in the
incubator will not below 25.
I4
4-15
For example, in Baby Mode

Mode, if the set temperature is 36 while the baby temperature rising
to 36.3, the air temperature in the incubator will not lower than 31.3; while the baby
temperature rising to 36.7 which is higher 0.5 than the set temperature, the air temperature in
the incubator will not lower than 25.
CONNECT THE PROBE OF SKIN TEMPERATURE SENSOR TO THE PATIENT:
In Baby Mode
Mode, make sure that the probe of skin sensor1 is attached closely on the skin of
patient. Put the probe on the right position of skin, and clean the position of skin where the skin
sensor located and the metal surface of skin sensor probe with alcohol or the moderate water to
wipe off the grease and dirt. In order to fix the probe'position, medical tape or the like can be used
to fix it Disposable skin temperature sensor can be fixed with its glue. If the patient lies on back,
please stick the metal surface of skin sensor probe between the xiphoid of the belly and the
bellybutton, to avoid the liver; if the patient bends over, stick the metal surface of skin sensor probe
on the back of patient, the best place is on the kidney. To make sure that the probe and the skin of
patient is attached closely; please fix it with medical staple. If the patient lies on back, as for the
position of probe, please follow the instruction of doctor.
NOTE: 1. Skin temperature sensor must be cleaned and disinfected before use.
2. Please do not put the skin sensor under the patient.
3. Skin sensor probe can not be regarded as the rectum thermometer.
WARNING
1. Make sure that the probe of skin sensor is attached closely on the skin of patient. If
the probe falls off the patient, the measured temperature from sensor is not the real
skin temperature, maybe the air temperature or the mattress temperature, and it may
cause the patient receive more heat or lose heat, even scald or death.
2. Please do not cover the blanket or diaper on the probe of skin sensor, because it will
affect the accuracy of temperature.
Skin sensor will measure the skin temperature of patient, not the real body
temperature, Therefore, measure the body temperature regularly, and check whether
the patient has a fever or not, whether the temperature of patient decreases.
4.5.3 OTHER OPERATION
A. Raise the head or foot of patient
Please raise the head or foot of patient according to the step F in section 4.4.3.
CAUTION: 1. Please do not add the over load on the mattress.
2. The mattress tilt will affect the temperature uniformity on the mattress, the
horizontal position of mattress is best state.
4-16
I4
B. Operation to the oxygen concentration control system.

Please reffer to the section 6.
C. Operation to the humidity control system
D. Operation of Neonate Bilirubin Phototherapy Equipment (if applicable)
Please find the accompany documents, the users manual for NEONATE BILIRUBIN
PHOTOTHERAPY EQUIPMENT XHZ-90, XHZ-90L.
E. Operation to the weighting control system
I4
4-17
SECTION 5
CLEANING AND MAINTENANCE
5.1 GENERAL
This section provides cleaning and maintenance instructions.
WARNING
1. Disconnect all the connections with oxygen feeding device before cleaning and
maintenance. Cleaning or maintenance in the environment full with oxygen will cause
fire or explosion.
2. The incubator with cabinet adopts the connector of power cord as the isolation
mains power supply, therefore, to make sure the safety, and pull off all powre cords
before cleaning.
5.2 CLEANING
This device must be cleaned and sterilized for the first time for initial use, or after used it for
one week.
5.2.1 DISASSEMBLY BEFORE CLEANING
A. Remove The Controller
Disconnect the Power Cord and Sensors from the side of the Incubator.Release the latch on
each side of the Controller as shown in Figure 5.1 to take out the controller.
Spanner
The controller can be taken out from the incubator, when the Spanner pull out to
>90
>90 direction.
WARNING: The Controller heater can be sufficiently hot to cause burns; avoid
removing the Controller or touching the heater until the unit has
switched..
been switched
FIGURE 5.1
I4
5-1
B. Remove the bassinet

Push bassinet inward as figure 5.2 directs and raise its right side as the arrow 1 indicates, till
the bassinet limitation horn is higher than the inlet (as enlarged figure 1 showes) and remove the
bassinet as the arrow 2 indicates and remove the bedsheet.
Limitation horn
Enlarged figure I
Inlet
FIGURE 5.2
C. Remove the air curtain
Raise the hood slowly as figure 5.3 directed, make the air curtain upright to the bassinet shelf
and move it out follow the direction of the arrow.
CAUTION: Before raising the hood, make sure that all installed accessories are all cut off.
FIGURE 5.3
5-2
I4
D. Remove the Main Deck

Refer to figure 5.4, rotate the knob to the unlocked position and take out the Main Deck.
Fixed knob
Locked
Unlocked
FIGURE 5.4
I4
5-3
E. Remove the inner wall

Remove the hood inner wall as figure 5.5 directed.
Step 1Move the limit hole in hood away from the position of fixed inner wall bolt
Step 2Remove the inner wall coping in the hood away from the fixed slot of inner wall, remove the
inner wall of the hood as well.
Step 3Press the inner wall on the access panel slightly as the arrow1 directed andremove the
inner wall out as arrow 2 directed.
FIGURE 5.5
5-4
I4
F. Remove Air Intake Tube Connector

See Figure 5.6, Move the Air Intake Tube out in direction of arrow 2 after disconnecting Air
Intake Tube from Air Tube Connector in direction of arrow 1
FIGURE 5.6
G. Remove Reservoir
Pull the Reservoir out slowly till it is locked as the figure 5.7 directs, then press it down slightly,
it can be pulled out.
Affusion meatus
Reservoir
FIGURE 5.7
CAUTION
CAUTION:: 1. Because the temperature of the water tank is high after the power of the
device is on as well as the heating groups are tighten then, so please take out
the water tank after it is totally cooling down to avoid damage to the heating
group.
2. The humidifying system is in the bottom of the reservoir. Don
ont put hands
into the reservoir to avoid being burned.
H. Remove the Access door gasket and Access door cuff, and Iris port sleeve from hood.
I. Remove the soft tubing from hood.
I4
5-5
5.2.2 CLEANING PROCEDURE

CAUTION: Some chemical cleaning agents may be conductive and/or leave a residue which
may permit a build-up of dust or dirt which may be conductive. Do not permit
cleaning agents to contact electrical components. Do not spray cleaning
solutions onto any of those surfaces.
A. Clean the skin temperature sensor
Use a disinfectant-detergent to thoroughly clean all surfacesincluding probe), then sterilize
with neutral disinfectants or ultraviolet disinfection.
CAUTION: Do not steep Sensor into disinfectant-detergent, and autoclave sterilization is
not allowed. Disposable skin temperature sensor is for single patient use only,
please discard after use.
B. Clean the Soft tubing, Gaskets, Iris Port Sleeves
Allow parts to soak as national registered neutral disinfectant-detergent, then remove them
and dry completely with a clean cloth or paper tower.
C. Clean the Hood, inner wall and sensor modular
Use a national registered neutral disinfectant-detergent to thoroughly clean all surfaces,
including all holes, indentations, Access Doors and Iris Ports then dry them with a clean cloth or
paper towel.
NOTE: Alcohol can cause crazing of the clear Acrylic panel. Do not use alcohol, acetone,
or any organic solvents for cleaning. Do not expose the panel assembly to direct
ultraviolet radiation.
D. Clean the controller
Use national registered neutral disinfectant-detergent to clean the all surfaces thoroughly.
Then dry it with clean cloth.
NOTE: Pay particular attention to avoid liquid seeping into the Controller Shell.
Please clean the heater after it is totally cooled down.
WARNNING
WARNNING:: Not clean the heater and fan will result in accumulate of fibre dust, baffle the
air flow. That will infulence the temperature control and result in high CO2
concentration.
E. Clean the bassinet, Main Deck, shelf and tray
paper towel.
CAUTION: Do not lubricate the Mattress Tilt Mechanism with oil or other potentially
F. Clean mattress cover
Use a national registered neutral disinfectant-detergent to thoroughly clean it and sun it after
washing it with clean water.
G. Clean Air filter
paper towel. If the air filter is dirt or is used for more than 2 months, please replace it.
5-6
I4
H. Clean Water tank and Humidity chamber fill spout

Open the two cover boards on the humidifying chamber and pull up the water proof as
figure5.8 indicates. Use the national registered neutral disinfectant-detergent to clean the all
surfaces and cupped place thoroughly. Clean it again with clean water and then dry it with clean
cloth or paper.
Please pay special attention that clean the inner and outter surface of the probe with the
around the detect point can control the microorganism breed in the water tank and ensure the
accuracy of the water level detecting.
When the scale appears visibly on the radiating cover inside the water tank, it is
recommended to soak it with table vinegar or the scale cleaning detergents which is used
exclusively for casting water dispenser. The soaking time is about 15min to 20 min. (The longer
the radiating cover be soaked, the better) .In the process of soaking, make sure that the cover is
immersed entirely. After soaking, scrub with bottle brush and rinse the cover till the scale is
cleaned completely.
Cover board
Reek outlet
Detecting probe
Radiating cover
Water proof
Water inlet hole on the bottom

CAUTION:: 1. Please clean the water tank after the radiating cover inside the water tank
CAUTION
totally cooleddown.
2. Make sure the water inlet hole on the bottom and the reek outlet hole of tank
throughable after cleaning.
3. If the water tank is uncleaned, especially there're dusts near the probe, there
will be a possibility that water-lacking alarm failure.
4. Please use soft cloth to wipe the surface of the probe when it is covered by
nobel metal. Do not use the hard material to scrape the probe so as not to
damage it.
5. When the scale appears on the radiating cover visibly, you must clean it in
time, or it will easily breed ground for bacterium and affect the humidification.
FIGURE 5.8
I. Clean NEONATE BILIRUBIN OHOTOTHERAPY EQUIPMENT
See the users manual for XHZ-90 and XHZ-90L.
J. Clean surface of device
paper towel.
5.2.3 REASSEMBLY AFTER CLEANING
NOTE: Before reassembling parts into Incubator, check carefully if there is any crack or
damage. Some disinfectant-detergent may cause crazing of plastic parts in
Incubator.
A. Install Humidity chamber fill spout in the reverse steps as they are moved out.
I4
5-7
B. Install Air Intake Tube in the reverse steps as they are moved out. Installed Air Intake Tube
must comply to Figure 5.9.
WARNING: Air Intake Tube must be placed inside the Air Intake Tube Connector
and completely sealed.
FIGURE 5.9
C. Place Main Deck back.
Be sure the two thumb screws that hold the Mattress Tray are tightened.
D. Install the air curtain and the inner wall as figure 5.3 and 5.4 direct.
E. Install the controller as the figure 5.1 directs
Controller is the key unit of Incubator and must be installed carefully.
Insert Controller into Base Assembly. After the whole part is inserted into Base Assembly,
depress the snaps at both sides of Controller until they are parallel to the side then pull the
Controller outward. If the Controller is not loosened, it is already locked. (See Figure 5.10)
Power socket of humidity

control on the base
Power socket of humidity

control on the controller
Correctinstallation state
CAUTION
CAUTION:: Power socket and plug of the humidity control are the power supply of the
incubator
incubators humidity control system. Do not force the controller in, or else the
power supply system will be dameged.
FIGURE 5.10
F. Rotating the iris entry sleeves, see figure 5.11.
Step 1: Install the elastic band over the inner ring of the port housing. Fold back and slip elastic
band over the outer ring of the port housing.
5-8
I4
Step 2: Rotate outer ring. If properly installed, the sleeve will open when reversing the rotation.
FIGURE 5.11
G. See figure 5.12, install the Access door gasket, and then isnatall the Access door cuff.
nner wall of hood
Inner
Hood inner side

Access door gasket
Outside of hood
Installation groove of Access door cuff
FIGURE 5.12
H. Install the soft tubing in figure 5.13.
NOTE: The opening of soft tubing should face outward.
Opening
FIGURE 5.13
I. Install the Mattress cover with the mattress, and put the bassinet inside hood according to
the opposite order. (see Figure 5.2)
Place the bassinet as the label indicates on the infant bed.
I4
5-9
5.3 STERILIZATION
NOTE: Please do not steam autoclave.
Please sterilize under low temperature.
5.4 MAINTENANCE
Please check the condition of the build-in rechargeable battery before the first use of device
or in the alternation of device using.
A. Operate the unit for a period of 12 to 24 hours.
B. Trigger a power failure alarm by disconnecting the AC power cord.
C. The power failure alarm should activate and continue to alarm for at least 10 minutes.
D. Reconnect the unit to the AC line and recharge the battery.
If the power failure alarm cannot last more than 10 minutes, please replace the rechargeable
battery. For this battery, it should be replaced by authorized and qualified service personnel.
5.5 TROUBLE SHOOTING

Troubleshooting of the infant incubator is presented in the following table. If the fault cannot
be localized from the table, the unit should be removed from service and servicing should be
referred to our company or authorized and qualified service personnel.
TROUBLESHOOTING TABLE
SYMPTOM
No indication, no alarm
POSSIBLE CAUSE
REMEDY
Power switched off
Switch on the power
Power off
Switch off the power
Power cord disconnected
Connect the power cord
The sensor box wrongly

placed
The sensor box right placed
Skin temperature sensor1

unconnect or illconnect
Connect the Skin temperature

sensor1 correctly.
Skin temperature sensor1

damaged
Replace the skin temperature

sensor1
Power supply is cut off
Alarm
The Alarm
Alarm light will flash,
and the Message indicator
Box Position
will show Box
Position
Alarm
The Alarm
Skin Sensor 1
will show Skin
5-10
I4
TROUBLESHOOTING TABLE (continued)

SYMPTOM
REMEDY
Oxygen sensor not

installed
Install the oxygen sensor1

correctly
Oxygen sensor damaged
Replace the Oxygen sensor1
Oxygen sensor2 not

installed
Install the oxygen sensor2

correctly
Oxygen sensor damaged
Replace the Oxygen sensor2
Ambient temperature
overhigh
Far away from the heat source

or decrease the ambient
temperature
High humidity
Decrease the humidity inside

hood
Door or panel of hood is

open
Close the door or panel of

hood
Ambient temperature
changes a lot
Check the Ambient

temperature
Alarm
The Alarm
Alarm light will flash, and
the Message indicator will
High Temp
show High
Temp
Heat source nearby
Far away from the heat source
Ambient temperature
changes a lot
Check the Ambient

temperature
Vertical Height adjustment

cabinet cant work up and down
(if applicable)
Power cord disconnected
Connect the power cord
Power switched off
Switch on the power
Alarm
The Alarm
Oxygen Sensor 1
show Oxygen
Alarm
The Alarm
Oxygen Sensor 2
show Oxygen
Alarm
The Alarm
Over Temp
show Over
Temp
Alarm
The Alarm
Low Temp
show Low
Temp
I4
POSSIBLE CAUSE
5-11
SECTION 6
OXYGEN CONCENTRATION CONTROL SYSTEM
6.1 GENERAL
This Section provides operation checkout procedure and operation instruction for the Oxygen
concentration control system.
6.2 INSTALLATION OF OXYGEN SENSOR

Stator
Sensor Cover
Stopper
Pull out the stator on the left side of sensor box as the arrow indicates, and pull out the sensor
box, unscrew 2 Cross groove countersunk head bolts, and take out the sensor cover, and then
unscrew the stopper on it.
Oxygen Sensor
Sensor Cover
Screw 2 oxygen sensors into the sensor cover clockwise.
Pull the connecting wire of oxygen sensor out and connect the sensor with the double wire of
green and black, and please connect another oxygen sensor with the other double wire of yellow
and black. After correctly connecting them, screw the sensor cover board down with two M38
cross groove head bolt, then push the sensor box into the original place in the hood.
CAUTION: 1. Do not block any of the holes on the sensor box.
2. Please pull out and push in the sensor box in correct way.
3. Sensor box is the important part of controlling the temperature of the
incubator, please treat it carefully.
FIGURE 6.1
6-1
I4
3 FUNCTIONAL DESCRIPTION
6.
6.3
Oxygn Sensor 1
The incubator has the function of controling the oxygen concentration. The O
Oxygen Sensor 2 alarm, Oxygen
Oxygen Not Same
High Oxygen
alarm, the Oxygen
Same alarm, High
Oxygen alarm and
Low Oxygen
Oxygen alarm are all applying for the function of controlling. The details of alarm message,
Low
please see the table 3.1. If the above alarms are actived, press the Silence /Reset key to stop
alarming for about 110s. The power of the heater is not cut off, and the oxygen control system will
Low Oxygen
cut off the oxygen supplying automatically (Except for L
Oxygen alarm).
4 CONNECTION OF OXYGEN INPUT CONNECTOR

6.
6.4
WARNING
1. Please read the operation manual carefully before operating.
2. Oxygen concentration control system must use oxygen analyzer to supply oxygen
through the oxygen input connector the relative operation must refer to the
operation manual of oxygen analyzer or other documents similarly.
3. Only given decompress valve or pressure adjusting valve can be used on the oxygen
cylinder.
4. According to the theory that the oxygen concentration inbreathed by the patient can
not judge his artery PO2 accurately, so other acceptable clinical measures should be
B
taken to testify the patient

patients artery PO2.
Connect the oxygen input tube which pass through the monitor with the oxygen input valve on
the left of the base (see the figure follows). Ensure they are sealed while connecting.
FIGURE 6.2
6-2
I4
5 OPERATION AND CALIBRATION PROCEDURES

6.
6.5
The system support with two kinds oxygen concentration calibration: 21% oxygen
concentration and 100% oxygen concentration. When the oxygen concentration of the
environment is below 21%, we suggest using 100% oxygen concentration calibration.
21% OXYGEN CONCENTRATION CALIBRATION
Keep the incubator in the environment which oxygen concentration is 21%.
a. Take out the sensor box under the condition of controller is turned off.
b. After press Oxygen Concentration Indicator key
key, turnning the controlleron to enter the
interface of 21% oxygen concentration calibration. The Oxygen Concentration indicator displays
CA, Set Temperature indicator displays 21. Press the Keypad Lock key
key, system starts
calibrating the 21% oxygen concentration automatically. If the calibration is correct, the Oxygen
Concentration indicator displays "21", if not, it displays "Er". When the displayed value is
incorrect, please calibrate the system again according to the steps listed above. If the displayed
value by the indicator is still incorrect, please ask the qualifyed service personnel to mend it.
% OXYGEN CONCENTRATION CALIBRATION
100%
100
a. Turn off the controller, pull the sensor box out as figure 6.3 shows, connect the oxygen
calibration device which equiped with oxygen connecting pipe with sensor box, supplying the
100% oxygen and maintain for more than 2min.
b. Press the Oxygen Concentration Indication key and turn on the power switch of the
controller, the system will enter into Oxygen Concentration calibration interface and the Oxygen
Concentration indicator displays CA, press Set Up key or Set Down key untill the Set
Temperature indicator displays "100". Press the Keypad Lock key
key, system starts celibrating the
100% oxygen concentration automatically. If the calibration is correct, the Oxygen Concentration
indicator displays "99", if not, it displays "Er". When the displayed value is incorrect, please
calibrate the system again according to the steps listed above. If the displayed value by the
indicator is still incorrect, please ask the qualifyed service personnel to mend it.
Sensor box
Oxygen concentration
calibration device
FIGURE 6.3
6-3
I4
CHECK THE OXYGEN CONCENTRATION MONITOR FUNCTION

1. Place a calibrated oxygen concentration analyzer in the middle of the bassinet.
2. Connect the oxygen input system, waitting until the oxygen concentration steady, between
the value displays in the Oxygen Concentration indicator and the oxygen concentration analyzer
displays should in the range of 3%.
CHECK THE FUNCTION OF OXYGEN CONCENTRATION DEVIATION ALARM

Connect the oxygen supply system with oxygen input connector and set the oxygen
concentration basic value at 30%. Waitting until the oxygen concentration display value reach the
basic value, then increase the oxygen flow rate rapidly. When the displayed oxygen concentration
Alarm
value deviates the basic value to +5%, the incubator alarming, the A
larm light will flash with
High Oxygen
continuous audible sound, and the Message indicator will show High
Oxygen. Set the oxygen
concentration basic value at 30%. Waitting until the oxygen concentration display value reach the
basic value, then decrease the oxygen flow rate rapidly.
When the displayed oxygen
Alarm
concentration value deviates the basic value to -5%, the incubator alarming, the A
larm light will
Low Oxygen
Oxygen. When
flash with continuous audible sound, and the Message indicator will show Low
alarm actived, press Silence /Reset key to stop alarming, but the alarm indicator light continously
shines until the deviation is less than 5%.
6 USING OF OXYGEN SUPPLY SYSTEM

6.
6.6
6.6.1 Preparation
Connecting the oxygen flowmeter and oxygen input valve with one PU-106.5 medical pipe.
6.6.2 Operation
Slect the oxygen concentration control value according to the requirement of the chief doctor.
Turn on the Oxygen Concentration indicator and press the Keypad Lock key
key, keypad lock
indicating light brighten up then. Press the Switch Setting Indicator key, and select the oxygen
concentration set indicator, which light will brighten up then. Press the Up/Down key to set the
oxygen concentration value. Select the suitable setting value, then press Keypad Lock key to
start work directly, or waiting for 10s without pressing any key to start working.
WARNING Over-high oxygen concentration will damage the patient seriously, so
follow the doctor
doctors requirement while using it and taking the relevant
oxygen input monitor to ensure oxygen flow and its concentration is
setted by the doctor.
6-4
I4
7 MAINT
EN
ANCE
6.
6.7
MAINTEN
ENANCE
A. Oxygen concentration sensor
When the oxygen concentration lifetime is in due, replace it even it is workable to ensure the
varacity of the detecting value. That is because:
The detecting accuracy of oxygen concentration sensor is influenced by the electrolyte inside
the sensor modular, and the electrolyte will be consumed along with the working time. So using the
over lifetime oxygen concentration sensor will result in wrong detected value.
B. Troubleshooting
Roubleshooting of the oxygen concentration sensor is presented in the following table. If the
fault cannot be localized from the table, the unit should be removed from service and servicing
should be referred to our company or authorized and qualified service personnel.
SYMPTOM
No indication of oxygen
concentration value
Alarm
The Alarm
Alarm light will
flash, and the Message
High
indicator will show High
Oxygen
Oxygen
Alarm
The Alarm
Alarm light will
flash, and the Message
Low
indicator will show Low
Oxygen
Oxygen
POSSIBLE CAUSE
Not install the oxygen sensor
Displayed oxygen concentration

too high
install the oxygen sensor
Please calibrate
sensor again
the
oxygen
Adjust the proper oxygen flow
Displayed oxygen concentration

too low
Please calibrate
sensor again
the
oxygen
Adjust the proper oxygen flow

Open the access door
6-5
I4
REMEDY
Close the access door
SECTION 7
HUMIDITY CONTROL SYSTEM
7.1 GENERAL
This section provides operation and checkout procedures and operation manual about
humidity control system.
7.2 FUNCTION DESCRIPTION

When the humidifying system is on working, user can set the humidity control value in
therange from 0% to 90%RH. The deviaton alarm value is 15%RH. In the humidity steady
condition, the incubator will alarming if the humidity is higher or lower than the setted value.
Vapour produced when the water in the humidity chamber flow by the heat pipe on the bottom
of the chamber, enters into the hood by vapour letout. The humidity control system enable the
humidity increasing inside the chamber. The evaporating speed decided by the power of the
heater. Theres a humidity sensor in thside the sensor modular of the hood which adjust the output
power of the evaporator. The details of alarm message, please see the table 3.1. If the alarms
about humidity are actived, press the Silence/Reset key to stop alarming for about 4 minute, the
power of the temperature heater is not cut off, the power of the humidity heater will automatic cut
High Humidity
off when the High
Humidity alarm is actived.
7.3 OPERATION AND CALIBRATION PROCEDURES

A. Raising the water in humidity chamber to the highest level, place a calibrated humidity
analyzer in the middle 10cm of the bassinet.
B. Prewarm the incubator to 36, set the humidity value to 50%.
C. Waiting until the value in the indicator to 50%RH, the Humidity indicator should display
50%RH10%RH.
D. Check the humidity deviation alarm
Turn the controller on, in the condition of starting the Humidity indicator, it should display the
value detected by humidity sensor. When the humiditying system is on working, set the humidity
value to 40%RH. Waitting until the humidity display value reach the setted value, then increase the
humidity display value to make it 15%RH higher than the setted value, the incubator alarming, the
Alarm
High
Alarm
Alarm light will flash with continuous audible sound, and the Message indicator will show High
Humidity
Humidity. Set the humidity value to 50%RH. Waitting until the humidity display value reach the
setted value, then decrease the humidity display value to make it 15%RH lower than the setted
Alarm
value, the incubator alarming, the Alarm
Alarm light will flash with continuous audible sound, and the
Low Humidity
Message indicator will show Low
Humidity. Press Silence /Reset key to stop alarming, but the
alarm indicator light continously shines until the deviation is less than 15%RH. If 4m later, the
alarming condition still exists, it will alarm again.
7-1
I4
7.4 USING OF HUMIDITY CONTROL SYSTEM

Apply the humidity celibration and operation procedure when first using the incubator orreuse
it after disassembly, clean, and maintain.
In any temperature, the relatively high humidity in the incubator will decrease
WARNING
WARNING
the heat vaporing from the patient and result in increasing the pacient
pacients
temperature. This is especially distincness in the neonate. Therefore,
temperature control mode
mode,, temperature value and humidity value should
certified by the chief doctor. Monitor the patient
patients recta and armpit
temperature according to the doctor
doctors instruction.
A. Connect the humidity control power plug of the controller with the humidity control power
socket inside the base (See figure 5.10) to complete the humidity control system.
B. Set the incubator in Air Mode and prewarm it according to the doctors director.
C. Pull the water tank out as figure 5.7 indicates, adding proper distilled water intothe tank.
1. Please do not use humidi
humiditty function under the water-lacking condition, or
else the humidify system will be damaged.
2. While the incubator is working, please make sure the water tank is pushed to
the correct location. Or else, it will effect the normally working of the controller.
3. For prolong the humidity device
devices lifetime, using clean distilled water only, don
dont
replace it with disinfected water.
4. Please clean the water tank and change the distilled water every 24 hours to
avoid the breed of microorganism and the pollution to the humidifying chamber.
Please wait to change the water until the water tank cools down, so as not to get
burned.
1. Please clean the water tank every time before add water in the tank. Dry it
IMPORTANT
IMPORTANT
with a clean cloth or paper towel for both inside and outside of the water
tank to ensure than water lacking alarm will normally working.
2. Please set the humidity value to 0%RH when you're not using the
"humidify" function. (It can also be turned down by humidity indicator
switch)
D. Turn on the Humidity Indicator key and press the Keypad Lock to enlighten its indicating
light. Press the Switch Setting Indicator key to select the humidity set indicator to make it shining.
Then set the humidity value by pressing Up/Down key
key. Slect the suitable setting value, then press
Keypad Lock to start work directly, or waiting for 10s without pressing any key to start working.
NOTE The actual humidity in the system is determined by the setted humidity of
theincubator and the surrounding condition.
7-2
I4
EN
ANCE
7.5 MAINT
MAINTEN
ENANCE
Troubleshooting of the humidity control system is presented in the following table. If the fault
cannot be localized from the table, the unit should be removed from service and servicing should
be referred to our company or authorized and qualified service personnel.
SYMPTOM
POSSIBLE CAUSE
Alarm
The Alarm
High Humidity
will show High
Humidity
Environmental humidity change

greatly
Check the surrounding

humidity condition
Alarm
The Alarm
Low Humidity
will show Low
Humidity
No distilled water in the tank
Add distilled water into the tank
Alarm
The Alarm
Low Water
will show Low
Water
No distilled water in the tank
Add distilled water into the tank

Wash it when there's a
need.
Alarm
The Alarm
Tank Position
will show Tank
Position
Bad connection between water

tank and the main body of the
device
Push the water tank to the

correct position to fully
connecting with the main body
of the device.
Alarm not be actived when

the water tank is lack of
water
Excessive microorganism breed

in the water tank or the water
tank haven't been cleaned for
many days.
Thoroughly clean the water

tank and clean around the
detect point with soft cloth in
disinfector.
After filling water to the

Low
water tank after Low
water
water alarm activing, the
function of "humidify" can't
be started immediately
Humidifier over-heat protection

unrecovered
Waiting for about 10 minutes
7-3
I4
REMEDY
SECTION 8
WEIGHING SYSTEM
8.1 GENERAL
This section provides operation and checkout procedures and operation manual about
weighing system.
Weighing system is selectable.
8.2 INSTALLATION
Install the weighing system in the incubator as figure 8.1 directs.
Refer the F in section 4.4.3, Rotate the mattress mechanism to the lowest, then open the front
access panel, place the bassinet accessoried with electrical scale on the mattress mechanism and
make sure it can be push in and pull out as the arrow1 and arrow2 figure.
Arrow
Opening
The arrow on the weight sensor must coherent

to the opening on the sensor socket to enable
insert correctly.
Weight sensor
WARNING: 1. Insert or pull out the skin sensor, you must hold the plug of skin sensor,
pulling the leads is forbidden.
2. Please do not bend the connection of sensor.
Insert the sensor plug of the electrical scale into the socket on the sensor modular correctly
FIGURE 8.1
I4
8-1
8.3 FUNCTION DESCRIPTION

The weighing system own the function of celebration and reset. These operation can be
actualized by operating the Zero key and Calibration key on the controller board. The display
range of weighing system is 100~8000g, and its display distinguish rate is 1g, the display precision
is 1%, and the reset range is 0~2000g.
8.4 OPERATION AND CALIBRATION PROCEDURES

E Apply the weight sensor celibration and operation procedure when first using the
NOTE
NOT
incubator orreuse it after disassembly, clean, and maintain.
CELIBRATE THE WEIGHING SYSTEM
A. take out all articles on the bassinet and make sure the mattess is clean.
B. Zero. Press the Zero key
key, the weighing value displayed by Weight indicator should be in
the range of 0000g5g, if not, please press the key again. If the reset value overs 0~2000g, after
pressing the key, the Weight indicator displays Err which mean the reset for the weighing system
failure.
C. Celibration. After reset the weighing system, please place standard poise of 5000g on the
center of the basinet and press the Calibration key for more than 10 seconds. After hearing the
sound like Ding, calibration is over. Then the Weight indicator should displays the value in the
range of 50005g, if not, please celibrate the weighing system again until the displayed value is in
the range of 50005g. If the displayed value cannot reach the standard value range, please ask
the qualifyed personnel to mend it.
CHECK THE CONNECTING CIRCUITRY OF THE WEIGHT SENSOR
If the connection between the weight sensor and the sensor modular failure, the Weight
indicator displays Err, when reconnect them, the indicator displays the actual weight weighing by
sensor.
8.5 OPERATION OF WEIGHING SYSTEM

After calibrating and reset the weighing system, lay the patient in, the Weight indicator will
display the patients weight by weight sensor.
8-2
I4
8.6 MAINTENANCE
Troubleshooting of the humidity control system is presented in the following table. If the fault
cannot be localized from the table, the unit should be removed from service and servicing should
be referred to our company or authorized and qualified service personnel.
SYMPTOM
No indication on
Weight indicator
POSSIBLE CAUSE
No power supply
Turn on the power of the

controller
The reset range is over 0~2000g
Take out every article on the

bassinet and keep the mattress
clean
The connection of weight sensor

is failure
Connect the weight sensor

correctly
The bassinet is not placed aclinic
Adjust the bassinet into aclinic
Infant is not placed in the centre

of the mattress
Lay the infant in the centre of

the mattress
Environmental temperature varies

greatly
Check the environmental

temperature
Weight indicator
displaysErr
Weighing inaccurate
I4
REMEDY
8-3

Ningbo YP 970

Uploaded by

Copyright:

Available Formats

Ningbo YP 970

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ningbo YP 970

Uploaded by

Copyright:

Available Formats

DAVID RR

NINGBO DAVID MEDICAL DEVICE CO., LTD.

DEVELOPMENT ZONE, NINGBO, ZHEJIANG PROVINCE, P.R.CHINA

MARKETING CENTER: NO. 100

Guidance and manufacture

Guidance and manufacture

Electromagnetic environment guidance

emissions are very low and are not likely to cause

establishments, including domestic establishments and

The YP-970 Infant Incubator is suitable for use in all

Guidance and manufacture

Guidance and manufacture

IEC 60601 test level

Floors should be wood, concrete

or ceramic tile. If floor are

covered with synthetic material,

2 kV for power supply

2kV for power

Mains power quality should be

that of a typical commercial or

Mains power quality should be

that of a typical commercial or

Voltage dips, short

Mains power quality should be

(>95% dip in UT)

(>95% dip in UT)

that of a typical commercial or

for 0.5 cycle

for 0.5 cycle

hospital environment. If the user

power supply input

(60% dip in UT)

(60% dip in UT)

that the YP-970 Infant Incubator

(30% dip in UT)

(30% dip in UT)

uninterruptible power supply or

(>95% dip in UT)

(>95% dip in UT)

UT is the a.c. mains voltage prior to application of the test level.

Guidance and manufacture

Guidance and manufacture

IEC 60601 test level

Electromagnetic environment - guidance

150 kHz to 80 MHz

outside ISM bands a

150 kHz to 80 MHz

80 MHz to 2.5 GHz

800 MHz to 2.5 GHz

Recommended separation distances between portable and mobile

150 kHz to 80 MHz

150 kHz to 80 MHz

outside ISM bands

800 MHz to 2.5 GHz

OPERATORS MANUAL FOR INFANT INCUBATOR

OPERATORS MANUAL FOR INFANT INCUBATOR

OPERATORS MANUAL FOR INFANT INCUBATOR

OPERATORS MANUAL FOR INFANT INCUBATOR

OPERATORS MANUAL FOR INFANT INCUBATOR