Motor Basics

AGSM 325

Motors vs Engines

Motors convert
electrical energy to
mechanical energy.
Engines convert
chemical energy to
mechanical energy.

www.PAControl.com 1
 Motors
Advantages
Low Initial Cost - $/Hp
Simple & Efficient Operation
Compact Size cubic inches/Hp
Long Life 30,000 to 50,000 hours
Low Noise
No Exhaust Emissions
Withstand high temporary overloads
Automatic/Remote Start & Control
Disadvantages
Portability
Speed Control
No Demand Charge

Magnetic Induction

Simple Electromagnet

Like Poles Repel

Opposite Poles Attract

www.PAControl.com 2
 Operating Principle

Motor Parts

Enclosure
Stator
Rotor
Bearings
Conduit Box
Eye Bolt

www.PAControl.com 3
 Enclosure
Holds parts together
Helps with heat dissipation
In some cases, protects internal components
from the environment.

Stator (Windings)
Stationary part of the motor sometimes referred to as the
windings.
Slotted cores made of thin sections of soft iron are wound
with insulated copper wire to form one or more pairs of
magnetic poles.

www.PAControl.com 4
 Rotor
Rotating part of the
motor.
Magnetic field from
the stator induces an
opposing magnetic
field onto the rotor
causing the rotor to
push away from the
stator field.

Wound Rotor Motors

Older motor designed to operate at variable speed
Advantages
Speed Control, High Starting Torque, Low Starting Current
Disadvantages
Expensive, High Maintenance, Low Efficiency

www.PAControl.com 5
 Bearings
Sleeve Bearings
Standard on most motors
Quiet
Horizontal shafts only
Oil lubricated
Ball (Roller) Bearings
Support shaft in any
position
Grease lubricated
Many come sealed
requiring no maintenance

Other Parts

Conduit Box
Point of connection of
electrical power to the
motors stator windings.
Eye Bolt
Used to lift heavy motors
with a hoist or crane to
prevent motor damage.

www.PAControl.com 6
 Motor Speed
Synchronous Speed
Speed the motors
magnetic field rotates.
Theoretical speed with
not torque or friction.
Rated Speed
Speed the motor
operates when fully
loaded.
Actual speed at full
load when supplied
rated voltage.

Synchronous Speed
Theoretical Speed
A well built motor may
approach synchronous
speed when it has no load.
Factors
Electrical Frequency
(cycles/second)
# of poles in motor

www.PAControl.com 7
 Rated Speed

Speed the motor

runs at when fully
loaded and supplied
rated nameplate
voltage.

Motor Slip
Percent difference between a motors
synchronous speed and rated speed.
The rotor in an induction motor lags slightly
behind the synchronous speed of the changing
polarity of the magnetic field.
Low Slip Motors
Stiff.High Efficiency motors
High Slip Motors
Used for applications where load varies significantlyoil
pump jacks.

www.PAControl.com 8
 Torque

Measure of force
producing a rotation
Turning Effort
Measured in pound-feet
(foot-pounds)

Torque-Speed Curve

Amount of Torque
produced by motors
varies with Speed.
Torque Speed Curves
Starting Torque
Pull Up Torque
Breakdown Torque

www.PAControl.com 9
 Motor Power
Output Power
Horsepower
Amount of power
motor can produce at
shaft and not reduce
life of motor.
Input Power
Kilowatts
Amount of power the
motor consumes to
produce the output
power.

Calculating Horsepower

Need Speed and

Torque
Speed is easy
Tachometer
Torque is difficult
Dynamometer
Prony Brake

www.PAControl.com 10
 Watts Law

Input Power
Single Phase
Watts = Volts X Amps X p.f.
Three Phase
Watts = Avg Volts X Avg Amps X p.f. X 1.74

Example

Is a 1 Hp 1-phase motor driving a fan overloaded?

Voltage = 123 volts
Current = 9 amps
p.f. = 78%
Watts = Volts X Amps X p.f.
Watts = 123 volts X 9 amps X 0.78 = 863.5 Watts
864 Watts / 746 Watts/Hp = 1.16 Hp
Is the motor overloaded?

www.PAControl.com 11
 Electrical = Input
We measured Input
Motors are rated as Output
Difference?
Efficiency 1.16 Hp
If the motor is 75% Input
efficient, is it overloaded?
Eff = Output / Input
Output = Eff X Input
0.75 X 1.16 Hp = 0.87 Hp
HP
The motor is NOT Output?
overloaded

Example #2
Is this 10 Hp, 3-phase motor overloaded?
Voltages = 455, 458, and 461 volts
Currents = 14.1, 14.0 and 13.9 amps
P.f. = 82%
Watts = Voltsavg X Ampsavg X p.f. X 1.74
Watts = 458v X 14a X 0.82 X 1.74 = 9148.6 Watts
9148.6 Watts / 746 Watts/Hp = 12.26 Hp
Is the motor overloaded?

www.PAControl.com 12
 Example #2
We measured Input
Motor is rated as Output
Difference? 12.26 Hp
Efficiency Input
If the motor is 90%
efficient, is it overloaded?
Eff = Output / Input
Output = Eff X Input
Hp
0.90 X 12.26 Hp = 11.0 Hp
Output ?
The motor IS overloaded!
How bad is the overload?

Motor Types
CLASSIFICATION OF MOTORS
AC MOTORS

Polyphase Universal Single-Phase

Synchronous Induction Synchronous Induction

Hysteresis Hysteresis
Reluctance Squirrel Reluctance Squirrel
Cage Wound Cage
Rotor Wound
Permanent
Rotor
Magnet Split Phase
Design A
Design B Capacitor Run
Wound Rotor Design C Repulsion Capacitor Start
Synchronous Design D Repulsion Start Capacitor Start/Run

www.PAControl.com 13
 Synchronous vs Induction Motors

Synchronous Motors Induction Motors

Turn at exactly the Turn at less than
same speed as the synchronous speed
rotating magnetic field. under load.
3600 rpm, 1800 rpm, 3450 rpm, 1740 rpm,
etc. etc.

NEMA 3 Phase Motors

3 Phase Induction
Motors
NEMA Torque-
Speed Design
Types
A,B,C,D,E

www.PAControl.com 14
 Design Type B

Todays Standard 3-
Phase Motor
Good Starting Torque
In-rush amps 4-6 times
full load amps
Good breakdown-
torque
Medium Slip

Design Type A

The old Standard

Higher starting torque
than B.
Higher in-rush current
(5-8 times full load
amps)
Good breakdown
torque

www.PAControl.com 15
 Design Type C
Common OEM
equipment on
reciprocating pumps,
compressors and other
hard starting loads.
High starting torque
Moderate starting
current (5-8 times
FLA)
Moderate breakdown
torque

Design Type D

Common on
applications with
significant loading
changes as a machine
operates.
Impact Loads
Punch Presses, Metal
Shears, etc.
Pump Jacks

www.PAControl.com 16
 Design Type E

Newest NEMA Category

Newer ultra-high efficiency motors
Higher Starting Torque
Higher Starting Current (8-12 times Running)
Ultra Low Slip (Higher Rated Speed)

Single Phase Induction Motors

Are not self starting
Require a starting mechanism.
The name generally
describes its starting
mechanism.
Split Phase
Capacitor Run
Capacitor Start
Capacitor Start-Capacitor Run
Shaded Pole
Synchronous
Universal

www.PAControl.com 17
 Split Phase Motor

Common small single

phase motor
Good Starting Torque
Moderate Efficiency
Moderate Cost
Small conveyors, augers,
pumps, and some
compressors
1/20th to Hp, available
to 1.5 Hp

Split Phase Motor

Starting winding in
parallel with Running
winding
Switch operates at
70-80% of full speed.
Centrifugal Switch
Sticks Open
Sticks Shut

www.PAControl.com 18
 Capacitor Run Motor
(Permanent Split Capacitor or PSC)

Primarily a fan
and blower
motor.
Poor starting
torque
Very low cost
motor.

Permanent Split Capacitor (PSC)

Capacitor in
Capacitor Winding
Provides a phase
shift for starting.
Optimizes running
characteristics.
No centrifugal switch

www.PAControl.com 19
 Capacitor Start Motor

Larger single phase

motors up to about 10
Hp.
A split phase motor
with the addition of a
capacitor in the
starting winding.
Capacitor sized for
high starting torque.

Capacitor Start Motor

Very high starting

torque.
Very high starting
current.
Common on
compressors and other
hard starting
equipment.

www.PAControl.com 20
 Capacitor Start-Capacitor Run

Both starting and

running characteristics
are optimized.
High starting torque
Low starting current
Highest cost
For hard starting loads
like compressors and
pumps.
Up to 10 Hp or higher
is some situations.

Capacitor Start-Run Motor

Larger single phase

motors up to 10 Hp.
Good starting torque
(less than cap start)
with lower starting
current.
Higher cost than cap
start.

www.PAControl.com 21
 Synchronous Motor

Special design for

constant speed at
rated horsepower and
below.
Used where
maintaining speed is
critical when the load
changes.

Universal Motor

Runs on AC or DC
Commutator and
brushes
Generally found in
portable power tools.
Lower Hp sizes

www.PAControl.com 22
 Universal Motor

Very high starting

torque.
Higher torque on DC
than AC (battery
operated tools)
The higher the rpm,
the lower the torque.

www.PAControl.com 23