Cellular Wireless Networks

Cellular Wireless Networks
Chapter 14
CS420/520 Axel Krings Page 1 Sequence 14
Principles of Cellular Networks

Underlying technology for mobile phones,
personal communication systems, wireless
networking etc.
Developed for mobile radio telephone
Replace high power transmitter/receiver systems
Typical support for 25 channels over 80km
Use lower power, shorter range, more transmitters
1
Cellular Network Organization
Multiple low power transmitters
100W or less
Area divided into cells
Each with own antenna
Each with own range of frequencies
Served by base station
Transmitter, receiver, control unit
Adjacent cells on different frequencies to avoid
crosstalk
Shape of Cells
Square
Width d cell has four neighbors at distance d and four at
distance 2 d
Better if all adjacent antennas equidistant
Simplifies choosing and switching to new antenna
Hexagon
Provides equidistant antennas
Radius defined as radius of circum-circle
Distance from center to vertex equals length of side
Distance between centers of cells radius R is 3R
Not always precise hexagons
Topographical limitations
Local signal propagation conditions
Location of antennas
2
Cellular Geometries
Frequency Reuse
Power of base transceiver controlled
Allow communications within cell on given frequency
Limit escaping power to adjacent cells
Allow re-use of frequencies in nearby cells
Use same frequency for multiple conversations
10 50 frequencies per cell
E.g.
N cells all using same number of frequencies
K total number of frequencies used in systems
Each cell has K/N frequencies
Advanced Mobile Phone Service (AMPS) K=395, N=7 giving 57
frequencies per cell on average
3
Characterizing Frequency
Reuse
D = minimum distance between centers of cells that use the same
band of frequencies (called co-channels)
R = radius of a cell
d = distance between centers of adjacent cells (d = 3 R)
N = number of cells in repetitious pattern
Reuse factor
Each cell in pattern uses unique band of frequencies
Hexagonal cell pattern, following values of N possible
N = I2 + J2 + (I x J), I, J = 0, 1, 2, 3,
Possible values of N are 1, 3, 4, 7, 9, 12, 13, 16, 19, 21,
D/R= 3N
D/d = N
Frequency
Reuse
Patterns
4
Increasing Capacity (1)
Add new channels
Not all channels used to start with
Frequency borrowing
Taken from adjacent cells by congested cells
Or assign frequencies dynamically
Cell splitting
Non-uniform distribution of topography and traffic
Smaller cells in high use areas
Original cells 6.5 13 km
1.5 km limit in general
More frequent handoff
More base stations
Cell Splitting
5
Increasing Capacity (2)
Cell Sectoring
Cell divided into wedge shaped sectors
3 6 sectors per cell
Each with own channel set
Subsets of cells channels
Directional antennas
Microcells
Move antennas from tops of hills and large buildings to
tops of small buildings and sides of large buildings
Even lamp posts
Form microcells
Reduced power
Good for city streets, along roads and inside large
buildings
Frequency Reuse Example

Assume: 32 cells, cell radius = 1.6 km, frequency bandwidth supports 336 channels,
reuse factor N=7.
How many channels per cell? What is total # of concurrent calls?
6
Operation of Cellular Systems
Base station (BS) at center of each cell
Antenna, controller, transceivers
Controller handles call process
Number of mobile units may in use at a time
BS connected to Mobile Telecommunications Switching
Office (MTSO)
One MTSO serves multiple BS
MTSO to BS link by wire or wireless
MTSO:
Connects calls between mobile units and from mobile to fixed
telecommunications network
Assigns voice channel
Performs handoffs
Monitors calls (billing)
Fully automated
Overview of Cellular System
7
Channels
Control channels
Setting up and maintaining calls
Establish relationship between mobile unit and
nearest BS
Traffic channels
Carry voice and data
Typical Call in
Single MTSO Area (1)
Mobile unit initialization

Scan and select strongest set up control channel
Automatically selected BS antenna of cell
Usually but not always nearest (propagation anomalies)
Handshake to identify user and register location
Scan repeated to allow for movement
Change of cell
Mobile unit monitors for pages (see below)
8
Typical Call in
Mobile originated call
Check if set up channel is free
Monitor forward channel (from BS) and wait for idle
Send number on pre-selected channel
Paging
MTSO attempts to connect to mobile unit
Paging message sent to BSs depending on called
mobile number
Paging signal transmitted on set up channel
Typical Call in
Call accepted
Mobile unit recognizes number on set up
channel
Responds to BS which sends response to
MTSO
MTSO sets up circuit between calling and
called BSs
MTSO selects available traffic channel within
cells and notifies BSs
BSs notify mobile unit of channel
9
Typical Call in
Ongoing call
Voice/data exchanged through respective BSs
and MTSO
Handoff
Mobile unit moves out of range of cell into
range of another cell
Traffic channel changes to one assigned to
new BS
Without interruption of service to user
Call Stages
10
Other Functions
Call blocking
During mobile-initiated call stage, if all traffic
channels busy, mobile tries again
After number of fails, busy tone returned
Call termination
User hangs up
MTSO informed
Traffic channels at two BSs released
Other Functions
Call drop
BS cannot maintain required signal strength
Traffic channel dropped and MTSO informed
Calls to/from fixed and remote mobile subscriber

MTSO connects to PSTN
MTSO can connect mobile user and fixed subscriber
via PSTN
MTSO can connect to remote MTSO via PSTN or via
dedicated lines
Can connect mobile user in its area and remote
mobile user
11
Mobile Radio
Propagation Effects
Signal strength
Strength of signal between BS and mobile unit strong enough to
maintain signal quality at the receiver
Not strong enough to create too much co-channel interference
Noise varies
Automobile ignition noise greater in city than in suburbs
Other signal sources vary
Signal strength varies as function of distance from BS
Signal strength varies dynamically as mobile unit moves
Fading
Even if signal strength in effective range, signal propagation
effects may disrupt the signal
Design Factors
Propagation effects
Dynamic
Hard to predict
Maximum transmit power level at BS and mobile
units
Typical height of mobile unit antenna
Available height of the BS antenna
These factors determine size of individual cell
Model based on empirical data
Apply model to given environment to develop
guidelines for cell size
12
Fading
Time variation of received signal
Caused by changes in transmission path(s)
E.g. atmospheric conditions (rain)
Movement of (mobile unit) antenna
Multipath Propagation
Reflection
Surface large relative to wavelength of signal
May have phase shift from original
May cancel out original or increase it
Diffraction
Edge of impenetrable body that is large relative to wavelength
May receive signal even if no line of sight (LOS) to transmitter
Scattering
Obstacle size on order of wavelength
Lamp posts etc.
If LOS, diffracted and scattered signals not significant
Reflected signals may be
If no LOS, diffraction and scattering are primary means
of reception
13
Reflection, Diffraction,
Scattering
Effects of Multipath
Propagation
Signals may cancel out due to phase differences
Inter-symbol Interference (ISI)
Sending narrow pulse at given frequency between
fixed antenna and mobile unit
Channel may deliver multiple copies at different times
Delayed pulses act as noise making recovery of bit
information difficult
Timing changes as mobile unit moves
Harder to design signal processing to filter out multipath
effects
14
Two Pulses in Time-Variant
Multipath
Types of Fading
Fast fading
Rapid changes in strength over distances about half wavelength
900MHz wavelength is 0.33m
20-30dB
Slow fading
Slower changes due to user passing different height buildings,
gaps in buildings etc.
Over longer distances than fast fading
Flat fading
Nonselective
Affects all frequencies in same proportion
Selective fading
Different frequency components affected differently
15
Error Compensation
Mechanisms (1)
Forward error correction
Applicable in digital transmission applications
Typically, ratio of total bits sent to data bits
between 2 and 3
Big overhead
Capacity one-half or one-third
Reflects difficulty of mobile wireless environment
Error Compensation
Mechanisms (2)
Adaptive equalization
Applied to transmissions that carry analog or
digital information
Used to combat inter-symbol interference
Gathering the dispersed symbol energy back
together into its original time interval
Techniques include so-called lumped analog
circuits and sophisticated digital signal
processing algorithms
16
Error Compensation
Mechanisms (3)
Diversity
Based on fact that individual channels experience independent
fading events
Provide multiple logical channels between transmitter and
receiver
Send part of signal over each channel
Does not eliminate errors
Reduce error rate
Equalization, forward error correction then cope with reduced
error rate
May involve physical transmission path
Space diversity
Multiple nearby antennas receive message or collocated multiple
directional antennas
More commonly, diversity refers to frequency or time diversity
Frequency Diversity
Signal is spread out over a larger frequency
bandwidth or carried on multiple frequency
carriers
E.g. spread spectrum
17
First Generation Analog
Original cellular telephone networks
Analog traffic channels
Early 1980s in North America
Advanced Mobile Phone Service (AMPS)
AT&T
Also common in South America, Australia, and
China
Spectral Allocation In North

America
Two 25-MHz bands are allocated to AMPS
One from BS to mobile unit (869894 MHz)
Other from mobile to base station (824849 MHz)
Bands is split in two to encourage competition
In each market two operators can be accommodated
Operator is allocated only 12.5 MHz in each direction
Channels spaced 30 kHz apart
Total of 416 channels per operator
Twenty-one channels allocated for control
395 to carry calls
Control channels are 10 kbps data channels
Conversation channels carry analog using frequency modulation
Control information also sent on conversation channels in bursts as
data
Number of channels inadequate for most major markets
For AMPS, frequency reuse is exploited
18
Operation
AMPS-capable phone has numeric assignment module
(NAM) in read-only memory
NAM contains number of phone
Assigned by service provider
Serial number of phone
Assigned by the manufacturer
When phone turned on, transmits serial number and phone
number to MTSO
MTSO has database of mobile units reported stolen
Uses serial number to lock out stolen units
MTSO uses phone number for billing
If phone is used in remote city, service is still billed to user's
local service provider
Call Sequence
1. Subscriber initiates call by keying in number and
presses send
2. MTSO validates telephone number and checks user
authorized to place call
Some service providers require a PIN to counter theft
3. MTSO issues message to user's phone indicating traffic
channels to use
4. MTSO sends ringing signal to called party
All operations, 2 through 4, occur within 10 s of initiating call
5. When called party answers, MTSO establishes circuit
and initiates billing information
6. When one party hangs up MTSO releases circuit, frees
radio channels, and completes billing information
19
AMPS Control Channels
21 full-duplex 30-kHz control channels
Transmit digital data using FSK
Data are transmitted in frames
Control information can be transmitted over
voice channel during conversation
Mobile unit or the base station inserts burst of data
Turn off voice FM transmission for about 100 ms
Replacing it with an FSK-encoded message
Used to exchange urgent messages
Change power level
Handoff
Second Generation (CDMA)

Higher quality signals
Higher data rates
Support of digital services
Greater capacity
Digital traffic channels
Support digital data
Voice traffic digitized
User traffic (data or digitized voice) converted to analog signal for
transmission
Encryption
Simple to encrypt digital traffic
Error detection and correction
(See chapter 6)
Very clear voice reception
Channel access
Channel dynamically shared by users via Time division multiple access
(TDMA) or code division multiple access (CDMA)
20
Code Division Multiple Access
Each cell allocated frequency bandwidth
Split in two
Half for reverse, half for forward
Direct-sequence spread spectrum (DSSS)

Advantages
Frequency diversity
Frequency-dependent transmission impairments (noise bursts, selective
fading) have less effect
Multipath resistance
DSSS overcomes multipath fading by frequency diversity
Also, chipping codes used only exhibit low cross correlation and low
autocorrelation
Version of signal delayed more than one chip interval does not interfere
with the dominant signal as much
chips per second (number of bits per second)
Privacy
From spread spectrum
Graceful degradation
With FDMA or TDMA, fixed number of users can access system
simultaneously
With CDMA, as more users access the system simultaneously, noise
level and hence error rate increases
Gradually system degrades
21
Self-jamming
Unless all mobile users are perfectly synchronized, arriving
transmissions from multiple users will not be perfectly aligned
on chip boundaries
Spreading sequences of different users not orthogonal
Some cross correlation
Distinct from either TDMA or FDMA
In which, for reasonable time or frequency guardbands,
respectively, received signals are orthogonal or nearly so
Near-far problem
Signals closer to receiver are received with less attenuation than
signals farther away
Given lack of complete orthogonality, transmissions from more
remote mobile units may be more difficult to recover
RAKE Receiver
If multiple versions of signal arrive more than one chip interval
apart, receiver can recover signal by correlating chip sequence with
dominant incoming signal
Remaining signals treated as noise
Better performance if receiver attempts to recover signals from
multiple paths and combine them, with suitable delays
Original binary signal is spread by XOR operation with chipping
code
Spread sequence modulated for transmission over wireless channel
Multipath effects generate multiple copies of signal
Each with a different amount of time delay (1, 2, etc.)
Each with a different attenuation factors (a1, a2, etc.)
Receiver demodulates combined signal
Demodulated chip stream fed into multiple correlators, each delayed by
different amount
Signals combined using weighting factors estimated from the channel
22
Principle of RAKE Receiver
IS-95
Second generation CDMA scheme
Primarily deployed in North America
Transmission structures different on forward
and reverse links
23
IS-95 Channel Structure
IS-95 Forward Link (1)

Up to 64 logical CDMA channels each occupying
the same 1228-kHz bandwidth
Four types of channels:
Pilot (channel 0)
Continuous signal on a single channel
Allows mobile unit to acquire timing information
Provides phase reference for demodulation process
Provides signal strength comparison for handoff
determination
Consists of all zeros
Synchronization (channel 32)
1200-bps channel used by mobile station to obtain
identification information about the cellular system
System time, long code state, protocol revision, etc.
24
IS-95 Forward Link (2)
Paging (channels 1 to 7)
Contain messages for one or more mobile stations
Traffic (channels 8 to 31 and 33 to 63)
55 traffic channels
Original specification supported data rates of up to
9600 bps
Revision added rates up to 14,400 bps
All channels use same bandwidth
Chipping code distinguishes among channels
Chipping codes are the 64 orthogonal 64-bit codes
derived from 64 64 Walsh matrix
Forward Link Processing

Voice traffic encoded at 8550 bps
Additional bits added for error detection
Rate now 9600 bps
Full capacity not used when user not speaking
Quiet period data rate as low as 1200 bps
2400 bps rate used to transmit transients in background noise
4800 bps rate to mix digitized speech and signaling data
Data transmitted in 20 ms blocks
Forward error correction
Convolutional encoder with rate
Doubling effective data rate to 19.2 kbps
For lower data rates encoder output bits (called code symbols)
replicated to yield 19.2-kbps
Data interleaved in blocks to reduce effects of errors by spreading
them
25
Scrambling
After interleaver, data scrambled
Privacy mask
Prevent sending of repetitive patterns
Reduces probability of users sending at peak power at same
time
Scrambling done by long code
Pseudorandom number generated from 42-bit-long shift register
Shift register initialized with user's electronic serial number
Output of long code generator is at a rate of 1.2288 Mbps
64 times 19.2 kbps
One bit in 64 selected (by the decimator function)
Resulting stream XORed with output of block interleaver
Power Control
Next step inserts power control information in
traffic channel
To control the power output of antenna
Robs traffic channel of bits at rate of 800 bps by
stealing code bits
800-bps channel carries information directing mobile
unit to change output level
Power control stream multiplexed into 19.2 kbps
Replace some code bits, using long code generator to
encode bits
26
DSSS
Direct-Sequence Spread Spectrum
Spreads 19.2 kbps to 1.2288 Mbps
Using one row of Walsh matrix
Assigned to mobile station during call setup
If 0 presented to XOR, 64 bits of assigned row sent
If 1 presented, bitwise XOR of row sent
Final bit rate 1.2288 Mbps
Bit stream modulated onto carrier using QPSK
Data split into I and Q (in-phase and quadrature)
channels
Data in each channel XORed with unique short code
Pseudorandom numbers from 15-bit-long shift register
Forward
Link
Transmission
27
Reverse Link
Up to 94 logical CDMA channels
Each occupying same 1228-kHz bandwidth
Supports up to 32 access channels and 62 traffic
channels
Traffic channels mobile unique
Each station has unique long code mask based on
serial number
42-bit number, 242 1 different masks
Access channel used by mobile to initiate call, respond to
paging channel message, and for location update
Reverse Link Processing

and Spreading
First steps same as forward channel
Convolutional encoder rate 1/3
Tripling effective data rate to max. 28.8 kbps
Data block interleaved
Spreading using Walsh matrix
Use and purpose different from forward channel
Data from block interleaver grouped in units of 6 bits
Each 6-bit unit serves as index to select row of matrix (26 = 64)
Row is substituted for input
Data rate expanded by factor of 64/6 to 307.2 kbps
Done to improve reception at BS
Because possible codings orthogonal, block coding enhances decision-
making algorithm at receiver
Also computationally efficient
Walsh modulation form of block error-correcting code
(n, k) = (64, 6) and dmin = 32
In fact, all distances 32
28
Data Burst Randomizer
Reduce interference from other mobile stations
Using long code mask to smooth data out over
20 ms frame
DSSS
Long code unique to mobile XORed with output
of randomizer
1.2288-Mbps final data stream
Modulated using orthogonal QPSK modulation
scheme
Differs from forward channel in use of delay
element in modulator to produce orthogonality
Forward channel, spreading codes orthogonal
Coming from Walsh matrix
Reverse channel orthogonality of spreading codes not
guaranteed
29
Reverse
Link
Transmission
Third Generation Systems

Objective to provide fairly high-speed wireless communications to
support multimedia, data, and video in addition to voice
ITUs International Mobile Telecommunications for the year 2000
(IMT-2000) initiative defined ITUs view of third-generation
capabilities as:
Voice quality comparable to PSTN
144 kbps available to users in vehicles over large areas
384 kbps available to pedestrians over small areas
Support for 2.048 Mbps for office use
Symmetrical and asymmetrical data rates
Support for packet-switched and circuit-switched services
Adaptive interface to Internet
More efficient use of available spectrum
Support for variety of mobile equipment
Flexibility to allow introduction of new services and technologies
30
Driving Forces
Trend toward universal personal telecommunications
Ability of person to identify himself and use any communication system
in globally, in terms of single account
Universal communications access
Using ones terminal in a wide variety of environments to connect to
information services
e.g. portable terminal that will work in office, street, and planes equally
well
GSM cellular telephony with subscriber identity module, is step
towards goals
Personal communications services (PCSs) and personal
communication networks (PCNs) also form objectives for third-
generation wireless
Technology is digital using time division multiple access or code-
division multiple access
PCS handsets low power, small and light
Alternative Interfaces (1)

IMT-2000 specification covers set of radio interfaces for
optimized performance in different radio environments
Five alternatives to enable smooth evolution from
existing systems
Alternatives reflect evolution from second generation
Two specifications grow out of work at European
Telecommunications Standards Institute (ETSI)
Develop a UMTS (universal mobile telecommunications system)
as Europe's 3G wireless standard
Includes two standards
Wideband CDMA, or W-CDMA
Fully exploits CDMA technology
Provides high data rates with efficient use of bandwidth
IMT-TC, or TD-CDMA
Combination of W-CDMA and TDMA technology
Intended to provide upgrade path for TDMA-based GSM systems
31
Alternative Interfaces (2)
CDMA2000
North American origin
Similar to, but incompatible with, W-CDMA
W-DCMA = Wideband Code Division Multiple Access
In part because standards use different chip rates
Also, cdma2000 uses multicarrier, not used with W-CDMA
IMT-SC designed for TDMA-only networks
IMT-FC can be used by both TDMA and FDMA
carriers
To provide some 3G services
Outgrowth of Digital European Cordless
Telecommunications (DECT) standard
IMT-2000 Terrestrial Radio

Interfaces
32
source: wikipedia
CDMA Design Considerations

Bandwidth and Chip Rate
Dominant technology for 3G systems is CDMA
Three different CDMA schemes have been adopted
Share some common design issues
Bandwidth
Limit channel usage to 5 MHz
Higher bandwidth improves the receiver's ability to resolve
multipath
But available spectrum is limited by competing needs
5 MHz reasonable upper limit on what can be allocated for 3G
5 MHz is enough for data rates of 144 and 384 kHz
Chip rate
Given bandwidth, chip rate depends on desired data rate, need
for error control, and bandwidth limitations
Chip rate of 3 Mcps or more reasonable
33
CDMA Design Considerations
Multirate
Provision of multiple fixed-data-rate logical channels to a given user
Different data rates provided on different logical channels
Traffic on each logical channel can be switched independently
through wireless fixed networks to different destinations
Flexibly support multiple simultaneous applications from user
Efficiently use available capacity by only providing the capacity
required for each service
Achieved with TDMA scheme within single CDMA channel
Different number of slots per frame assigned for different data rates
Subchannels at a given data rate protected by error correction and
interleaving techniques
Alternative: use multiple CDMA codes
Separate coding and interleaving
Map them to separate CDMA channels
Time and Code Multiplexing
34
Summary
principles of wireless cellular networks
operation of wireless cellular networks
first-generation analog
second-generation CDMA
third-generation systems
35

Cellular Wireless Networks

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cellular Wireless Networks

Uploaded by

Copyright:

Available Formats

Cellular Wireless Networks

CS420/520 Axel Krings Page 1 Sequence 14

Principles of Cellular Networks

CS420/520 Axel Krings Page 2 Sequence 14

CS420/520 Axel Krings Page 3 Sequence 14

CS420/520 Axel Krings Page 4 Sequence 14

CS420/520 Axel Krings Page 5 Sequence 14

CS420/520 Axel Krings Page 6 Sequence 14

CS420/520 Axel Krings Page 7 Sequence 14

CS420/520 Axel Krings Page 8 Sequence 14

CS420/520 Axel Krings Page 9 Sequence 14

CS420/520 Axel Krings Page 10 Sequence 14

Frequency Reuse Example

CS420/520 Axel Krings Page 12 Sequence 14

Overview of Cellular System

CS420/520 Axel Krings Page 14 Sequence 14

CS420/520 Axel Krings Page 15 Sequence 14

Mobile unit initialization

CS420/520 Axel Krings Page 16 Sequence 14

CS420/520 Axel Krings Page 17 Sequence 14

CS420/520 Axel Krings Page 18 Sequence 14

CS420/520 Axel Krings Page 19 Sequence 14

CS420/520 Axel Krings Page 20 Sequence 14

CS420/520 Axel Krings Page 21 Sequence 14

Calls to/from fixed and remote mobile subscriber

CS420/520 Axel Krings Page 23 Sequence 14

CS420/520 Axel Krings Page 25 Sequence 14

CS420/520 Axel Krings Page 27 Sequence 14

CS420/520 Axel Krings Page 28 Sequence 14

CS420/520 Axel Krings Page 29 Sequence 14

CS420/520 Axel Krings Page 30 Sequence 14

CS420/520 Axel Krings Page 31 Sequence 14

CS420/520 Axel Krings Page 32 Sequence 14

CS420/520 Axel Krings Page 33 Sequence 14

CS420/520 Axel Krings Page 34 Sequence 14

CS420/520 Axel Krings Page 35 Sequence 14

Spectral Allocation In North

CS420/520 Axel Krings Page 37 Sequence 14

CS420/520 Axel Krings Page 38 Sequence 14

CS420/520 Axel Krings Page 39 Sequence 14

Second Generation (CDMA)

CS420/520 Axel Krings Page 41 Sequence 14

Code Division Multiple Access

CS420/520 Axel Krings Page 43 Sequence 14

CS420/520 Axel Krings Page 44 Sequence 14

CS420/520 Axel Krings Page 45 Sequence 14

CS420/520 Axel Krings Page 46 Sequence 14

CS420/520 Axel Krings Page 47 Sequence 14

IS-95 Forward Link (1)

CS420/520 Axel Krings Page 49 Sequence 14

Forward Link Processing

CS420/520 Axel Krings Page 50 Sequence 14

CS420/520 Axel Krings Page 51 Sequence 14

CS420/520 Axel Krings Page 52 Sequence 14

CS420/520 Axel Krings Page 54 Sequence 14

CS420/520 Axel Krings Page 55 Sequence 14

Reverse Link Processing

CS420/520 Axel Krings Page 57 Sequence 14

CS420/520 Axel Krings Page 58 Sequence 14

CS420/520 Axel Krings Page 59 Sequence 14

Third Generation Systems

CS420/520 Axel Krings Page 60 Sequence 14