Eliwell Kontrolori PDF

Index
1 Indicators temperature, humidity and pressure 10
2 Controllers temperature, humidity and pressure 18
3 Temperature Regulators 36
4 Timers and Pulse Counters 44
5 Controllers for Refrigeration 50
6 Data Acquisition and Printing 104
7 Systems 110
8 Accessories 134
9 Electrical measurements 150
10 Mechanical Controllers 150
11 Product Selection Guide 174
Disclaimer 185
2
Index of Contents
1 Indicators 10
temperature, humidity and pressure
Eliwell Meters
1.1 EM300 - EM300LX temperature 11
1.2 EM300 - EM300LX humidity 12
EWTM
1.3 EWTM 053 13
EWTL
1.4 EWTL 300 14
1.5 EWTL 310 15
EWMETER
1.6 EWMETER 900 16
2 Controllers 18
temperature, humidity, pressure
IC - Universal Controllers
2.1 IC 901 19
2.2 IC 901/A 20
2.3 IC 902 21
2.4 IC 912 IC 912 LX 22
2.5 IC 915 IC 915 LX 23
2.6 IC 917 IC 917 LX 24
2.7 IC 974 IC974 LX 25
EWPC 800
2.8 EWPC 800 26
EWDR 900
2.9 EWDR 902 27
2.10 EWDR 905 28
EWTR 900
2.11 EWTR 910 29
2.12 EWTR 920 30
2.13 EWTR 930 31
2.14 EWTR 940 32
3
WM - Wall Mounting Controllers
2.15 WM 901 (/A /B) 33
2.16 WM 100/150 34
2.17 WM 500/550 35
3 Temperature Regulators 36
3.1 EWTN 970 37

3.2 EWTN 980 38
3.3 EWTQ 905 39
3.4 EWTQ 915/985 40
3.5 EWTQ 995 41
4 Timers and Pulse Counters 44
Timers
4.1 EWPH 480 45
4.2 EWTS 950 46
4.3 EWTS 330/S 47
Pulse Counters
4.4 EWCH 485 49
5 Controllers for Refrigeration 50
Digifrost Line
5.1 ID 961 ID 961 LX 52
5.2 ID 970 ID 970 LX 53
5.3 ID 971 ID 971 LX 54
5.4 ID 974 ID 974 LX 55
5.5 ID 975 LX 56
5.6 ID 983LX - ID985 LX 57
5.7 IS 972 LX with EWEM 233 Slave module 59
5.8 IS 974 LX with EWEM 243 Slave module 61
4
Index of Contents
Defrost Timers and

Blind Controllers for Refrigeration
5.9 EWTS 70 63
5.10 EWTS 72 64
5.11 EWTS 90 65
5.12 EWLC 74 66
5.13 EWDR 981 67

5.14 EWDR 983 /C /CS LX 68
5.15 EWDR 984 69
5.16 EWDR 985 /CS LX 71
5.17 IWC 720 73

5.18 IWC 730 74
5.19 IWC 740 75
5.20 IWC 750 76
5.21 IWP 740 LX 77

5.22 IWP 750 LX, IWP 760 LX 79
5.23 IWP 985 LX /CS LX 81
EWPC 1000
5.24 EWPC 1000(/C, /S) 83
EWTB 1000
5.25 EWTB 1000(/C, /S) 85
Compressor Control
5.26 EWCM 400 (412 415 418) 87
5.27 EWCM 800 89
5.28 EWCM 900 91
5.29 EWCM 809/NH3/S 93

5.30 WM 961 (/A, /B) 31
Solutions for Refrigeration

5.31 EWFC 1000 95
5.32 MT6 96
5
Fans Controllers
5.33 FASEC 33 97
5.34 FASEC 43/43C 98
5.35 FASEC 53 99
5.36 FASEC 100 100
5.37 FASEC 500 101
5.38 WM 203 102
5.39 WM 253 103
6 Data Acquisition and Printing 104
6.1 PRINTWELL 1200 105

6.2 PRINTWELL 1200 Slave Module 106
6.3 EWLP 120 107
7 Systems 110
Monitoring and Remote Assistance solutions

7.1 Televis 150 111
7.2 Televis 200 113
7.3 TelevisStation 3500/3700 115
7.4 TelevisCompact 20/40/60 117
7.5 TelevisInteractive Family 119
Televis Network
7.6 Example and notes for the installation 121
7.7 PCInterface1100 123
Data Control and Acquisition Modules

7.9 EWTV 200 125
7.10 EWTV 240 126
7.11 EWTV 270 127
7.12 EWTV 280 128
7.13 EWTV 150 129
Accessories
7.14 BusAdapter 130 130
7.15 BusAdapter 150/350 131
7.16 SmartAdapter 132
6
Index of Contents
8 Accessories 134
8.1 Temperature Probes 135

8.2 EWHS 280, 300, 310 137
8.3 EWPA 007, 030 138
8.4 Miscellaneous 139
8,5 Switches 141
8,6 Fan Controllers 142
9 Electrical Measurement 144
Multimeters
9.1 IE 103 145
9.2 IE 123 146
9.3 IE 203 147
9.4 IE 303 148
10 Mechanical Controllers 150

temperature and pressure
10.1 O16/O52 for Temperature 151

10.2 O16/O52 for Pressure 153
10.3 O17 155
10.4 P30 157
10.5 K Series (1450, 22, 52, 5461) 159
10.6 Varifix 164
10.7 G Series (G60, G63) 165
10.8 J10J11 167
10.9 2001 Series (Paragon Defrost Timer) 168
10.10 V/VH Cycle reversing valves 169
10.11 T24/T25 Electronic Timers 171
10.12 V16 (Solenoide valve) 173
7
11 Product Selection Guide 174
11.1 Selection Guide for Controllers 175

11.2 Selection Guide for Refrigeration Controllers 177
Disclaimer 185
8
Please use this blank section for your personal notes
1 Indicators
The range provides the Eliwell Meters

possibility to view temperature, 1.1 EM300 - EM300LX temperature 11
pressure, or humidity values 1.2 EM300 - EM300LX humidity 12
using different instrument
EWTM
formats: front panel 32x74 mm 1.3 EWTM 053 13
or 72x72 mm with square
casing, both for panel EWTL
mounting. 1.4 EWTL 300 14
1.5 EWTL 310 15
Liquid crystal, battery powered
temperature meters are also EWMETER
available. 1.6 EWMETER 900 16
10
EM 300, EM 300LX
Electronic digital temperature indicators
Description Technical Data

The range of Eliwell digital indicators represents an Front panel protection: IP65.
excellent measurement solution for all commercial and light Casing: plastic body in PC+ABS resin, UL94 V-0,
industry applications. polycarbonate window, keys in thermoplastic resin.
EM300(LX) is a device that measures temperature values by
Dimensions: 74 x 32 mm (front part) and 30 mm depth
means of PTC or NTC temperature probes. The precision of
(without terminals).
their digital conversion enables display of the measured
values with a resolution of a tenth, when required. Mounting: panel-mounting with 71x 29 mm drilling
A special algorithm delivers a signal which activates a template (+0.2/-0.1 mm).
maximum and minimum alarms if the measured values Operating temperature: -5...55C
exceed the threshold values specified by the user by means Storage temperature: -30...85C.
of the parameters available in the programming menu.
Operating and storage humidity: 10...90 %RH (non
The direct power supply at 230V also eliminates the need
condensing).
for an external transformer. Standard models have sizes of
32x74 mm with a depth of 30 mm, which ensures Display: 3 digits and a half + sign.
maximum installation flexibility and their adaptability to all Analogue input: 1 input see table
kinds of systems. Measuring range: -999...1000
Precision: above 0.5% of the bottom scale +1 digit.
EM 300LX:
models LX can also be connected to TelevisSystem and to Resolution: 0.1C.
the optional Copy Card for the quick programming of Buzzer output: only for models equipped with this
parameters when equipped with a TTL serial port. component.
Consumption: 3VA max.
Model Analogue input Range(C)
Power supply: 230V.
EM 300(LX) NTC -50...110
EM 300(LX) PTC -55...150
EM 300(LX) Pt100 -100...600 EM 300LX Models:
EM 300(LX) tc-J-K 0...600 / 0...999
Serial connection: TTl for the connection of:
- Copy Card
- TelevisSystem
Wiring Diagram Description of Wiring Diagram

Common:
1-2 Power supply
3-4 Temperature probe input
EM300(LX) - 230 V A
T Temperature probe
EM 300LX:
A TTL input for Copy Card
1 2 3 4 5 and TelevisSystem
11
EM 300, EM 300LX
Electronic digital humidity indicators

Eliwell digital indicators represent the best measurement Front panel protection: IP65.
solution for all commercial and light industry applications. Casing: plastic body, PC+ABS resin, UL94 V-0, polycarbonate
EM300(LX) measures humidity values by means of a probe window, keys in thermoplastic resin.
or 4...20mA current signals. Thanks to the accuracy of the
Dimensions: 74 x 32 mm (front part) and 30 mm depth
digital conversion function, this indicator can also display
(without terminals).
the measured values with a resolution of one tenth, if
required. Mounting: panel-mounting with 71x 29 mm drilling
Its special algorithm enables the configuration of maximum template (+0.2/-0.1 mm).
and minimum alarms for values exceeding the thresholds Operating temperature: -5...55C
specified by the user. Thresholds can be configured using Storage temperature: -30...85C
the parameters in the main programming menu.
Operating and storage humidity: 10...90 %RH (non
This indicator has a 230V DC power supply that eliminates
condensing)
the need of using an external transformer. Standard models
have a size of 32x74 mm and depth of 30 mm, which Display: 3 digits and a half + sign.
ensures maximum installation flexibility and their Analogue input: 1 V-I input see table
adaptability to all kinds of systems. Measuring range: -999...1000
Precision: above 0.5% of the bottom scale +1 digit
EM 300LX:
LX indicators can also be connected to TelevisSystem and to Resolution: 0.1 digit
the optional Copy Card to quickly configure programming Buzzer output: only for models equipped with this
parameters. This option requires the use of a TTL serial port. component.
Consumption: 3VA max.
Model Analogue input
Power supply: 230V
EM 300(LX) EWHS 280/300/310
EM 300(LX) 0...1/5/10V; 0/4...20mA EM 300LX Models:
Serial connection: TTl for the connection of:
- Copy Card
- TelevisSystem

Common:
1-2 Power supply
3 Input - with current and voltage
EM300(LX) - 230 V A 4 Input + with current and voltage
5 Power supply 12Vc
EM 300LX:
1 2 3 4 5 A TTL input for Copy Card and TelevisSystem
V-I
12
EWTM 053
electronic digital thermometer

The EWTM 053 electronic temperature indicators are Front panel protection: IP65
designed to display and record minimum and maximum Casing: plastic, PC+ABS plastic, self-extinguishing, UL94 V0
values on a 3 digit display + sign, with or without decimal
Size: front panel 31x64 mm, depth 33 mm (harness
point.
excluded)
Measuring range: 50110 C (58230 F).
These indicators have a LED (for calibration function, on the Mounting: panel-mounting, 59x26 mm hole
side of the display) in addition to a LED for the minus sign. Connections: faston 2.8 for probe, 6.3 mm for power
The availability of the decimal point (and its automatic supply
display) varies according to models. Operating temperature: from 0 to 60C, humidity
If available, the decimal point is displayed for values
1090% (non condensing)
50.099.9 (C, F) included.
The minus sign is displayed by means of a LED. The Storage temperature: from 30 to 75C, humidity
standard probe, with NTC probe, is in PVC with reinforced 1090% (non condensing)
insulation and Fast-on connector. 2 2.8 mm Fast-on Display: 3 digits plus sign, 12.5 mm high
connectors are used for connection purposes.
Analogue input: for NTC probe with reinforced insulation
These indicators are able to record and display the
and Fast-on connector
minimum and maximum temperature measured. The
recording function enables 10 seconds after the indicator Measurement range: 50110C
has been switched on. Resolution: 0.1 C or 1C
It is also possible to store the minimum and maximum Accuracy: above 0.5 C
temperature values as soon as the indicator is switched on.
Consumption: 0.5 VA.
The data storage function interrupts if an E1 alarm occurs
while a key is pressed. Power supply: 230 Va 10% or 12 Va/c 10%, 50/60 Hz.

12 Probe input
34 Power supply
EWTM 052/053
1 2 3 4
13
EWTL 300
LCD digital thermometer

EWTL 300 LCD digital thermometers have a temperature Mounting: 2 mm thick panel, 45.8x26.4 mm hole
probe linked to the instrument through a 1, 2 3.5 mm thick panel, 46x26.4 mm hole
or 3 meter cable.
>3.5 mm thick, 46.2x26.4 mm hole
Measuring range: from 20 to 70 C.
These thermometers are powered by a 1.5 V LR 44 battery Measurement range: 2070C; (0160F)
or equivalent model with a 12 months life. Resolution: 0.1 C.
Accuracy: 1 C from 0 to 40 C.
Battery: one (1) battery 1.5 V LR 44 or equivalent model.
Battery life: about 12 months.
Refreshing frequency: 10 seconds.
Probe: linked to the instrument, 1.5 m cable.
Dimensions
44,5
48 13,5
11,3
28,6
25
14
EWTL 310
LCD digital thermometer

EWTL 310 LCD digital thermometers have a temperature Size: front panel 62x30mm, depth 19 mm
probe linked to the instrument through a 0.5, Mounting: panel, on 58 x 26 mm hole.
1 or 2 meter cable.
Display: 2 and a half digit LCD display.
The measurement range goes from 20 to 70 C.
These thermometers are powered by 1.5 V LR 44 battery or Measurement range: 2070C.
equivalent model with a 12 months life. Resolution: 1C.
(Front battery access) Accuracy: above 0.5% of bottom scale.
Power supply: one (1) battery 1.5 V LR 44 or equivalent model.
Refreshing frequency: 12 seconds.
Probe: linked to the instrument with 0.5 m, 1 m, 2 m or 3 m
cable.
Dimensions
58
62 19
30
26
15
EWMETER 900
temperature, humidity and
pressure indicator

EWMETER 900 electronic indicators can measure or detect Casing: plastic, PC+ABS, V0 selfextinguishing.
temperature, humidity or pressure. Size: front panel 72x72 mm, depth 102 mm (terminals
These instruments have an input that can be immediately excluded).
used for temperature (PTC, Ni100, TcJ, TcK), humidity
Mounting: panel-mounting, 67x67 mm hole.
(EWHS 280/300/310) or pressure (EWPA 007/030) probes
or with a 420 mA current input. Connections: screw terminals for 4 mm2 leads (power
EWMETER 900 indicators have a standard size of 72x72 mm connections require one lead per terminal only).
and a 230 Va power supply. Operating temperature: 560C.
Storage temperature: 3075C.
Operating humidity: 1090 % non condensing.
Analogue Input Range
Display: 3 digits plus sign, 12.5 mm high.
PTC -55...150
Pt100-Ni100 -100...600 / -50...650 Analogue input: PTC, Ni100, Pt100, Tc (J, K) probe, (420
TcJ-TcK 0...600 / 0...999 mA, Ri = 41) current, EWHS 280/300/310, EWPA 007/030.
EWPA 007/030 0,5...0,8 / 0...30 Bar Display range: depending on probe.
EWHS 280/300/310 20...100/0...100/20...100 RH% Resolution: 1 or 0.1 C, 1 or 0.1% R.H., 1 or 0.1 Bar.
Accuracy: above 0.5% of bottom scale.
NOTE: overall range for different kinds of probes (the
range may be limited with specific types of cables, tips and Consumption: 5 VA max.
sensors). Special probes are available on request. Power supply: 230 Va 10%, 50/60 Hz.

78910 Probe input
T 8 9 10 8 9 10 8 9 10 7 8 9 10 8 9 10
EWMETER 900 1112 Power supply
+
11 PTC Pt100 / Ni100 Pt100 / Ni100 420 mA TcJ / TcK
12
P 7 8 9 RH 7 8 9 10
EWPA 007 EWHS 300 RH.

EWPA 030
NC
NC
RH 7 8 9 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10
7
8
9 EWHS 28/280 EWHS 31 T EWHS 31 RH EWHS 310 T EWHS 310 RH
10
T RH T RH
T + RH 7 8 9 10 7 8 9 10 7 8 9 10 7 8 9 10
EWHS 31 T + RH EWHS 310 T + RH
16
2 Controllers
Eliwell offers a complete IC - Universal Controllers

range of instruments to 2.1 IC 901 19
control temperature, relative 2.2 IC 901/A 20
2.3 IC 902 21
humidity, pressure and
2.4 IC 912 IC 912 LX 22
industrial processes. 2.5 IC 915 IC 915 LX 23
Five different sizes: with 2.6 IC 917 IC 917 LX 24
32x74 mm front panel, with 2.7 IC 974 IC974 LX 25
72x72 mm front panel and
EWPC 800
round body, with 72x72 mm 2.8 EWPC 800 26
front panel and square body,
in standard size for wall-mounting EWDR 900
and for 4 DIN modules. 2.9 EWDR 902 27
2.10 EWDR 905 28
All these controllers have 1
or 2 intervention points, EWTR 900
ON/OFF function and mode 2.11 EWTR 910 29
programming options 2.12 EWTR 920 30
2.13 EWTR 930 31
(heating or cooling or
2.14 EWTR 940 32
neutral zone).
Some models are available WM - Wall Mounting Controllers
with 1 or 2 intervention 2.15 WM 901 (/A /B) 33
2.16 WM 100/150 34
points and PID function.
2.17 WM 500/550 35
A selection of probes
designed to meet all possible
operating requirements in
the -80 and 1.200C range.
18
IC 901
single stage temperature controller

IC 901 controllers have one point of intervention only and Front panel protection: IP65
can be used both for heating and cooling applications. Casing: plastic in PC+ABS UL94V0 resin, polycarbonate
These controllers also have an input for the PTC glass, thermoplastic resin keys
thermostatic probe (the NTC input can be selected with a
Front panel dimensions: 32x74 mm, depth 60 mm
parameter) and a relay output for management of the load.
The values measured by the probes are displayed with two Mounting: panel-mounting, with 29x71 mm (+0.2/0.1mm)
digits and sign. All models have TTL connections that enable drilling template
the controllers to be used with Copy Card, the quick Connections: screw terminals for <2,5mm2 (one lead per
programming accessory. bracket, in compliance with VDE regulations)
Operating temperature: 555C
Storage temperature: 3085C
Probe Measurement range (C) Display Operating environment humidity: 1090% RH (non condensing)
NTC 50110,0 -50...99
Storage environment humidity: 1090% RH (non condensing)
PTC 55150,0 -50...99
Digital output: refer to attached table
Relay output Amp. capacity* Hp power Analogue input: refer to attached table
Regulation 8 (3) 1/2
Serial: TTL port for Copy Card
Regulation 15 1
Display: 2 digits plus sign
Regulation 20 2
Resolution: 1C (F)
*Maximum rating varies according to the type of terminal Accuracy: above 0.5% of bottom scale + 1 digit.
block used and the applicability of standards.
Consumption: 3 VA (115/230 V model), 1.5 VA (12 V model)
Power supply: 230, 115 Va, or 12 Va/c 10%, 50/60 Hz.

12 Relay N.C.
IC 901 - 12 V A 13 Relay N.O.

67 Power supply
89 Probe input
1 2 3 6 7 8 9 A TTL input for Copy Card
Warning: check the power supply specified on the

instrument label: contact the Sales Office for further
information on relay capacity and power supply.
IC 901 - 230 V A
1 2 3 6 7 8 9
19
IC 901/A
with alarm output

IC 901 controllers have one point of intervention only and Front panel protection: IP65.
can be used both for heating and cooling applications. Casing: plastic, PC+ABS UL94V0 resin, polycarbonate glass,
These controllers also have an input for the PTC thermoplastic resin keys.
Front panel dimensions: 32x74 mm, depth 60 mm.
The values measured by the probes are displayed with two Mounting: panel-mounting, with 29x71 mm (+0.2/0.1mm)
digits and sign. All models have TTL connections that enable drilling template.
the controllers to be used with Copy Card, the quick Connections: screw terminals for <2,5mm2
programming accessory. (one lead per bracket, in compliance with VDE regulations).
The IC 901A model also has an output for the alarm relay
Operating temperature: 555C;
and acoustic signal buzzer.
Operating environment humidity: 1090% RH (non condensing).
Probe Measurement range (C) Display
NTC 50110,0 -50...99 Storage environment humidity: 1090% RH (non condensing).
PTC 55150,0 -50...99 Digital output: refer to attached table.
Analogue input: refer to attached table.
Relay output Amp. capacity* Hp power
Serial: TTL port for Copy Card.
Regulation 8 1/2
Regulation 15 1 Display: 2 digits plus a sign.
Regulation 20 2 Resolution: 1C (F).
Alarm 8 1/2 Accuracy: better of 0.5% than the end of scale + 1 digit.
Consumption: 3 VA (115/230 V model), 1.5 VA (12 V
*Maximum rating varies according to the type of terminal
model).
Power supply: 230, 115 Va, or 12 Va/c 10%, 50/60 Hz.

12 Relay N.O.
IC 901A - 12 V A 13 Relay N.C.

45 Alarm relay
67 Power supply
1 2 3 4 5 6 7 8 9 10 810 Probe input


IC 901A - 230 V A
1 2 3 4 5 6 7 8 9 10
20
IC 902

IC 902 controllers have one point of intervention only and Frontal protection: IP65.
can be used both for heating and cooling applications. Casing: plastic, PC+ABS UL94V0 resin, polycarbonate glass,
These controllers also have an input for the PTC thermoplastic resin keys.
Front panel dimensions: 32x74, depth 60 mm.
The values measured by the probes are displayed with three Mounting: panel-mounting, with 29x71 mm (+0.2/0.1mm)
and a half digits and sign. All models have TTL connections drilling template.
that enable the controllers to be used with Copy Card, the Connections: screw terminals for <2,5mm2 (one lead per
quick programming accessory. bracket, in compliance with VDE regulations).
Operating temperature: 555C.
Storage temperature: 3085 C.
Operating environment humidity: 1090% RH (non condensing).
Storage environment humidity: 1090% RH (non condensing).
Digital output: refer to attached table.
Serial: TTL port for Copy Card and Televis.
Probe Measurement range (C)
NTC 50110,0 Display: 3 and half digits plus sign.
PTC 50140,0 Resolution: 1C or 0.1C (selectable with a parameter).
Accuracy: above 0.5% of bottom scale + 1 digit.
Relay output Amp. capacity* Hp power
Consumption: 3 VA (115/230 V model), 1.5 VA (12 V model).
Regulation 8 1/2
Regulation 15 1 Power supply: 230, 115 Va, or 12 Va/c 10%, 50/60 Hz.
Regulation 20 2
*Maximum rating varies according to the type of terminal

12 Relay N.C.
13 Relay N.O.
IC 902 - 12 V A
67 Power supply
89 Probe input
A TTL input for
1 2 3 6 7 8 9 10
Copy Card

IC 902 - 230 V A
1 2 3 6 7 8 9 10
21
IC 912, 912LX
one stage temperature, humidity and
pressure controller

IC 912, IC 912/R, IC 912/P, IC 912/V-I Front panel protection: IP65.
IC 912 controllers have one point of intervention only and Casing: plastic, PC+ABS UL94V0 resin, polycarbonate glass,
can be used for temperature (IC 912), relative thermoplastic resin keys.
humidity (IC 912/R) and pressure (IC 912/P) control,
provided for ONOFF operation.
Some models have an input for PTC/NTC thermostatic Mounting: panel-mounting, with 29x71 mm (+0.2/0.1mm)
probes or for Pt100/Tcj/Tck probes, drilling template.
EWHS280/300/310 humidity probes, for EWPA007/030 Connections: screw terminals for <2,5mm2 (one lead per
pressure transducers, for 0/4..20 mA, 0..1/5/10 V current bracket, in compliance with VDE regulations).
and voltage signals (selectable with a parameter). Operating temperature: 555C.
The values measured by the probes are displayed with three
and a half digits and a minus sign. All models have TTL
connections that enable the controllers to be used with Operating and storage environment humidity: 1090% RH*
Copy Card, the quick programming accessory. *(non condensing).
IC 912LX Digital output: refer to attached table.
The IC 912LX version includes a connection for
TelevisSystem, or alternatively for networks with ModBUS
protocol. Digital input: 1 free from voltage input (LX model).
Serial: TTL port for Copy Card and TelevisSystem (LX mod).
Model Analog input
Display: 3 and half digits plus sign.
IC 912 NTC/PTC/Pt100/TcJ/TcK
IC 912/P EWPA 007/030 Resolution: 1 or 0.1.
IC 912/R EWHS 280/300/310 Accuracy: above 0.5% of bottom scale + 1 digit.
IC 912/V-I 01/5/10 V 0/420 mA Consumption: 3 VA (115/230 V model), 1.5 VA(12 V model).
Power supply: 1224 Va/c; 230, 115 Va, or 12 Va/c 10%,
Relay output Amp. capacity Hp power
50/60 Hz. Please contact the Sales Office for further
Regulation 8 1/2
information on relay and power supply ratings.

Common
IC 912 - 12 V A 12 Relay N.O. 9 + voltage input
8 9 10 11 12 13 Relay N.C. 10 + current input
67 Power supply 11 12 Vc input
1 2 3 6 7 8 current and A TTL input for Copy Card
voltage input T Temperature probe input
+ -
IC 912 LX
8 9 10 11 A TTL input for Copy Card and TelevisSystem
8-9 Digital Input (Pt100/TC model)
IC 912 - 230 V A
T
8-11 Digital Input (PTC/NTC model)
1 2 3 6 7 8 9 10 11
22
IC 915, 915LX
two stage temperature, humidity and
pressure controller

IC 915, IC 915/R, IC 915/P, IC 915/V-I Front panel protection: IP65.
IC 915 controllers have two points of intervention only and Casing: plastic, PC+ABS UL94V0 resin, polycarbonate glass,
can be used for temperature (IC 915), relative thermoplastic resin keys.
humidity (IC 915/R) and pressure (IC 915/P) control,
provided for ONOFF operation.
Depending on models, they may have an input for PTC/NTC Mounting: panel-mounting, with 29x71 mm (+0.2/0.1mm)
thermostatic probes or for Pt100/Tcj/Tck probes, drilling template.
EWHS280/300/310 humidity probes, for EWPA007/030 Connections: screw terminals for <2,5mm2 (one lead per
pressure transducers, for 0/4..20 mA, 0..1/5/10 V current bracket, in compliance with VDE regulations).
and voltage signals (selectable with a parameter). Operating temperature: 555C
and a half digits and a minus sign. All models have TTL
connections that enable the controllers to be used with Operating environment humidity: 1090% RH*
Copy Card, the quick programming accessory. Storage environment humidity: 1090% RH*
IC 915LX *(non condensing)
The IC 915LX version includes a connection for
Digital output: refer to attached table
TelevisSystem , or alternatively for networks with ModBUS
protocol. Analogue input: refer to attached table
Serial: TTL port for Copy Card and TelevisSystem (LX mod).
Model Analog input
Display: 3 and half digits plus sign
IC 915 NTC/PTCPt100/TcJ/TcK
IC 915/P EWPA 007/030 Resolution: 1 or 0.1(selectable with a parameter)
IC 915/R EWHS 280/300/310 Accuracy:above 0.5% of bottom scale + 1 digit
IC 915/V-I 01/5/10 V 0/420 mA Consumption: 3 VA (115/230 V model), 1.5 VA (12 V model)
Power supply: 1224 Va/c; 230, 115 Va, or 12 Va/c 10%,
Relay output Amp. capacity Hp power
50/60 Hz. Please contact the Sales Office for further
Out 1 8(3) 1/2
Out 2 8(3) 1/2

Common
12 Relay 1 N.O. 9 + voltage input
IC 915 - 230 V A 13 Relay 1 N.C. 10 + current input
45 Relay 2 N.O. 11 12 Vc input
8 9 10 11 12 Pt100/TC A TTL input for Copy Card
67 Power supply
1 2 3 4 5 6 7
8 current and T Temperature probe input
voltage input
+ -
IC 915 LX
8 9 10 11 NTC/PTC A TTL input for Copy Card and TelevisSystem
8-9 Digital Input (Pt100/TC model)
T
IC 915 - 12 V A
8-11 Digital Input (PTC/NTC model)
1 2 3 4 5 6 7 8 9 10 11 V-I
23
IC 917, 917LX
two-stage temperature controller with
PID function

IC 917 Front pane protection: IP65.
IC 917 controllers have two points of intervention, Casing: plastic, PC+ABS UL94V0 resin, polycarbonate glass,
dependent or independent, with ONOFF, PD, thermoplastic resin keys.
PID action, and Soft Start function. They can be used for
temperature control.
Depending on the model, they may have an input for Mounting: panel-mounting, with 29x71 mm (+0.2/0.1mm)
PTC/NTC thermostatic probes (selectable with a parameter). drilling template.
The values measured by the probes are displayed with three Connections: screw terminals for <2,5mm2 (one lead per
and a half digits and a minus sign. All models have TTL bracket, in compliance with VDE regulations).
connections that enable the controllers to be used with Operating temperature: 555C.
Copy Card, the quick programming accessory.
IC 917LX Operating environment humidity: 1090% RH*.
The IC 917LX version includes a connection for Storage environment humidity: 1090% RH*
TelevisSystem and a digital input that can be selected with *(non condensing).
a parameter.
Digital output: refer to attached table.
Probe Measurement range (C) Analogue input: refer to attached table.

NTC 50110,0 Serial: TTL port for Copy Card and TelevisSystem (LX mod).
PTC 55150,0 Display: 3 and half digits plus sign
Pt100 -50...650
Resolution: 1 or 0.1(selectable with a parameter)
TcJ/TcK -40...750/-40...1350
Accuracy: above 0.5% of bottom scale + 1 digit
Relay output Amp. capacity Hp power Consumption: 3 VA (115/230 V model), 1.5 VA (12 V model).
Output 1 8(3) 1/2 Power supply: 1224 Va/c; 230, 115 Va, or 12 Va/c 10%,
Output 2 8(3) 1/2 50/60 Hz. Please contact the Sales Office for further

Common IC 917 LX
12 Relay 1 N.O. 8-9 Digital Input
13 Relay 1 N.C. (Pt100/TC model)
IC 917 - 12 V A
45 Relay 2 N.O. 8-11 Digital Input

(PTC/NTC model)
8 9 10 11 12 Pt100/TC 67 Power supply
1 2 3 4 5 6 7
A TTL input for
810 Probe input
Copy Card and
A TTL input for Copy Card TelevisSystem
+ -
IC 917 - 230 V A
8 9 10 11
1 2 3 4 5 6 7
24
IC 974, 974 LX
two-stage temperature controller with
digifrost functions
S
IC 974 Front panel protection: IP65.
IC974 controllers have two analogue inputs for NTC Casing: plastic, PC+ABS UL94 V-0, polycarbonate glass,
temperature probes (the PTC input can be selected with a thermoplastic resin keys.
parameter) and four digital relay outputs, free from voltage,
Dimensions: front panel 74x32 mm, depth 59 mm (without
for the management of heating and cooling functions inside
terminals).
the cell, for defrost functions and for the control the
evaporator fans. Mounting: panel-mounting, with 71x29 mm (+0,2/0,1 mm)
The defrost cycle can be timed or controlled by the drilling template.
evaporator probe using the cycle end temperature. Operating temperature: 555C.
The values measured by the probes are displayed with three Storage temperature.: 3085C.
and a half digits and a minus sign. The decimal point can be Operating and storage humidity: 1090 % RH (non
programmed with a parameter. The buzzer is optional. All
condensing).
models have TTL connections that enable the controllers to
be used with Copy Card, the quick programming accessory. Display: 3 digits and a half + sign.
Analogue input: one PTC or NTC input (selectable with a
IC 974 LX parameter).
LX models can also be connected to TelevisSystem. The input Digital input: 1 free from voltage digital input, selectable
of this model can also be used to select the operating mode with a parameter.
(manual changeover). Serial: TTL for Copy Card and TelevisSystem.
All models have a 12 V power supply.
Digital output: 4 relay outputs (see table).
Probe Display range (C) See the label on the instrument for information on the
NTC 50110,0 capacity of relays.
PTC 55150,0 Buzzer output: only for models with this feature.
Measuring range: 55 a 140C.
Relay output Rating (amp) Power (hp) Accuracy: above 0.5% of bottom scale + 1 digit.
Out A 8 (3) 1/2 Resolution: 0.1C (0.1F) (selectable with a parameter).
Out B 8 (3) 1/2 Consumption:
Out C 8 (3) 1/2 230V model: 3 VA max.
Out D 5 (3) 1/4 12/24V model: 1,5 VA max.
Power supply: 12/24 Va/c 10% or 230Va 10% 50/60 Hz.

1-2 Input probe 1 (temperature control)
1-3 Input probe 2 (evaporator)
5-7 Digital input 1
10 - 11 12Va power supply
1 2 3 4 5 6 7 10 11 A
12 - 13 13 Relay A N.O.
12 - 14 14 Relay A N.C.
15 - 16 16 Relay B N.O.
15 - 17 17 Relay C N.O.
12 13 14 15 16 17 18 19 IC 974 LX - 12V 18 - 19 19 Relay D N.O.
A A TTL input fo r Copy Card and Televis
25
EWPC 800
one stage temperature controller

EWPC 800 controllers have one point of intervention only Front panel protection: IP65.
and be used both for hot and cold Casing: plastic, ABS.
applications. Depending on models, they have inputs for
Size: front panel 72x72 mm, back of the instrument
PTC, Pt100, TcJ or TcK thermostatic probes.
The values measured by the probes are displayed with three 60 mm, depth 98 mm.
and a half digits and a minus sign. All these controllers are 60 mm, depth 98 mm.
available in 72x72 standard format with round casing. Mounting: panel on a 61 mm. hole, with fixing bracket.
Analogue input Range
PTC -55...150 Storage temperature: 3075C.
Pt100-Ni100 -100...600 / -50...650 Display: 3 digits, 12.5 mm high.
TcJ-TcK 0...600 / 0...999 Inputs (depending on models): PTC, Pt100, Tc (J, K).
EWPA 007/030 0,5...0,8 / 0...30 Bar
Main output: 1 output on 8(3)A 250Va SPDT relay.
EWHS 280/300/310 20...100/0...100/20...100 RH%
Resolution: 1C for reading without a decimal point, 0,1C
NOTE: overall range for different kinds of probes (the for decimal point measurements (a resolution of 5C or
range may be limited with specific types of cables, tips and 0,5C respectively can also be set).
sensors). Special probes are available on request. Accuracy: better of the 0.5% than the end of scale.
Power supply (depending on model): 230, 115, 24 Va 10%,
50/60 Hz; 12 Va/c 15%, 50/60 Hz.

12 Relay N.O.
13 Relay N.C.
EWPC 800
45 Power supply
6 7 8 6 7 8 678 Probe input
PTC TcJ / TcK

1
2 8 6 7 8 6 7 8
3 7
4 6
5
Pt100 Pt100
26
EWDR 902
pressure controller

EWDR 902 controllers have one point of intervention and Casing: for 4 DIN rail mounting, 70x85 mm, plastic, ABS
can be used to control temperature resin, self-extinguishing, UL94V0.
(EWDR 902/T), relative humidity (EWDR 902/R) and pressure Size: front panel 70x85 mm, depth 61 mm.
(EWDR 902/P). Depending on models, they may have an
Mounting: DIN rail (Omega 3, connected to the ground) or
input for thermostatic probes (PTC, Ni100, Pt100, TcJ, TcK,
wall-mounting.
420 mA current), humidity probes (EWHS 280/300/310) or
pressure probes (EWPA 007/030). The values measured by Connections: screw terminals for 2.5 mm2 leads.
the probes are displayed with three digits. These controllers Operating temperature: 560C.
are available in 4 DIN standard size with 230, 115, 24 Va or Storage temperature: 3075C.
12 Va/c. power supplies.
Display: 3 digits, 12.5 mm high.
Data storage: on permanent memory (EEPROM).
Analogue input Range Inputs (depending on model): PTC, RTD (Ni100, Pt100), Tc
PTC -55...150 (J, K), current (420 mA; Ri = 41 ) for EWDR 902/T; EWHS
Pt100-Ni100 -100...600 / -50...650 280/300/310 for EWDR 902/R and EWPA 007/030 for EWDR
TcJ-TcK 0...600 / 0...999 902/P.
EWPA 007/030 0,5...0,8 / 0...30 Bar Main output: 1 output on 8(3)A 250Va SPDT relay.
EWHS 280/300/310 20...100/0...100/20...100 RH%
Resolution: 1C , 0,1C (a resolution of 5C or 0,5C
respectively can also be set).
range may be limited with specific types of cables, tips and Accuracy: better than 0.5 % of the end of scale.
sensors). Special probes are available on request. Power supply (depending on model): 230, 115, 24 Va 10%;
12 Va/c 15%, 50/60 Hz.

13 Power supply
EWDR 902/T EWDR 902/R 101112 Probe input
1 3 10 11 12 10 11 12 10 11 12 10 11 12 10 11 12
1317 Relay N.O.
PTC Pt100 / Ni100 Pt100 / Ni100 EWHS 280 1517 Relay N.C.
EWDR 902
10 11 12
10 11 12 10 11 12
13 17 +
15
EWHS 310
TcJ / TcK 420 mA
EWDR 902/P
10 11 12
EWPA 007/030
27
EWDR 905
pressure controllers

EWDR 905 controllers are devices with two points of Casing: for 4 DIN rail mounting, 70x85 mm, plastic, ABS
intervention with a neutral zone; they can be used to resin, self-extinguishing, UL94V0.
control temperature (EWDR 905/T), relative humidity (EWDR Size: front panel 70x85 mm, depth 61 mm.
905/R), and pressure (EWDR 905/P). Depending on models,
Mounting: DIN rail (Omega 3, connected to the ground) or
they may have an input for thermostatic probes (PTC,
wall-mounting.
Ni100, Pt100, TcJ, TcK, 420 mA current), humidity probes
(EWHS 280/300/310) or pressure probes (EWPA 007/030). Connections: screw terminals for 2.5 mm2 leads.
The values measured by the probes are displayed with three Operating temperature: 560 C.
digits. These controllers are available in 4 DIN standard size Storage temperature: 3075 C.
with 230, 115, 24 Va, 12 Va/c. power supplies.
Analogue input Range Data storage: on permanent memory (EEPROM).
PTC -55...150 Inputs (depending on model): PTC / RTD (Ni100, Pt100) / Tc
Pt100-Ni100 -100...600 / -50...650 (J, K) / current (420 mA; Ri = 41 ) for EWDR 905/T;
TcJ-TcK 0...600 / 0...999 EWHS 280/300/310 for EWDR 905/R and EWPA 007/030 for
EWPA 007/030 0,5...0,8 / 0...30 Bar EWDR 905/P
EWHS 280/300/310 20...100/0...100/20...100 RH% Main output: 2 outputs on 8(3)A 250Va SPDT relay.
Resolution: 1C, 0.1C (a resolution of 5C or 0.5C
respectively can also be set).
range may be limited with specific types of cables, tips and
sensors). Special probes are available on request. Accuracy: above 0.5 % of bottom scale
Power supply (depending on model): 230, 115, 24 Va 10%;
12 Va/c 15%, 50/60 Hz.

13 Power supply
EWDR 905/T EWDR 905/R 101112 Probe input

1 3 10 11 12 10 11 12 10 11 12 10 11 12 10 11 12 1317 Relay 1 N.O.
1517 Relay 1 N.C.
PTC Pt100 / Ni100 Pt100 / Ni100 EWHS 280
EWDR 905
10 11 12
2024 Relay 2 N.C.
10 11 12 10 11 12
2022 Relay 2 N.O.
13 15 17 20 22 24 +
EWHS 310
TcJ / TcK 420 mA
EWDR 905/P
10 11 12
EWPA 007
EWPA 030
28
EWTR 910
pressure controller

EWTR 910 controllers have 1 point of intervention only with Casing: plastic in PC+ABS, V0 selfextinguishing.
ON/OFF and PID function (optional). They can be used for Size: front panel 72x72 mm, depth 102 mm.
temperature (EWTR 910), relative humidity (EWHR 910) and
Mounting: panel-mounting with bracket; 67x67 mm drilling
pressure (EWPR 910) control.
template.
Depending on models, they may have an input for
thermostatic probes (PTC, Ni100, Pt100, TcJ, TcK, 420 mA Connections: screw terminals for 2.5 mm2 leads (one lead
current), humidity probes (EWHS 280/300/310) or pressure per terminal only), which can be disconnected.
probes (EWPA 007/030). Operating temperature: 560C.
The values measured by the probes are displayed with three Storage temperature: 3075C.
or four digits, depending on models. These controllers are
Display: 3 or 4 digits, 12.5 mm high.
available in standard 72x72 mm size with square casing and
230, 115, 24 Va or 12 Va/c. power supplies. Data storage: on permanent memory (EEPROM).
Inputs (depending on model): PTC / RTD (Ni100, Pt100) / Tc
Analogue input Range (J, K) / current (420 mA; Ri = 41 ) for EWTR 910; EWHS
PTC -55...150 280/300/310 for EWHR 910 and EWPA 007/030 for EWPR 910.
Pt100-Ni100 -100...600 / -50...650 Main output: 1 output on 8(3)A 250Va SPDT relay or static
TcJ-TcK 0...600 / 0...999 (SSR) 0/12 Vc/40 mA output.
EWPA 007/030 0,5...0,8 / 0...30 Bar
Programmable analogue output (optional): 420 mA or 05
EWHS 280/300/310 20...100/0...100/20...100 RH%
V, depending on the model.
NOTE: overall range for different kinds of probes (the Resolution: 1 , 0.1 (a resolution of 5 or 0.5 can be selected)
range may be limited with specific types of cables, tips and Accuracy: above 0.5 % of bottom scale.
sensors). Special probes are available on request. Power supply (depending on model): 12 Va/c 15%; 230,
115, 24 Va 10%, 50/60 Hz.

56 Analogue output
EWTR 910 EWHR 910 78910 Probe input
8 9 10 8 9 10 8 9 10 7 8 9
910 series
1112 Power supply
11
12
13
PTC Pt100 / Ni100 Pt100 / Ni100 EWHS 280 1315 Relay N.O.
14
7 8 9 10

5
15
8 9 10 8 9 10
1415 Relay N.C.
+ 16
6
+ 17
7
18 + EWHS 310
8
TcJ / TcK 420 mA
9
10
EWPR 910
7 8 9
EWPA 007
EWPA 030
29
EWTR 920
pressure controller

EWTR 920 controllers are devices with two points of Casing: plastic, PC+ABS, V0 selfextinguishing.
intervention and can be used to control temperature Size: front panel 72x72 mm, depth 102 mm.
(EWTR 920), relative humidity (EWHR 920), and pressure
Mounting: panel-mounting with bracket; 67x67 mm drilling
(EWPR 920). Depending on models, they may have an input
template.
for thermostatic probes (PTC, Ni100, Pt100, TcJ, TcK, 420
mA current), humidity probes (EWHS 280/300/310) or Connections: screw terminals for 2.5 mm2 leads (one lead
pressure probes (EWPA 007/030). The values measured by only per terminal), which can be disconnected.
the probes are displayed with three or four digits, Operating temperature: 560C.
depending on models. These controllers are available in Storage temperature: 3075C.
standard 72x72 mm size with square casing and 230, 115, 24
Va or 12 Va/c. power supplies.
Analogue input Range Inputs (depending on model): PTC / RTD (Ni100, Pt100) / Tc
PTC -55...150 (J, K) / current (420 mA; Ri = 41 ) for EWTR 920; EWHS
Pt100-Ni100 -100...600 / -50...650 280/300/310 for EWHR 920 and EWPA 007/030 for EWPR
TcJ-TcK 0...600 / 0...999 920.
EWPA 007/030 0,5...0,8 / 0...30 Bar Main outputs: 2 output on 8(3)A 250Va SPDT relay or static
EWHS 280/300/310 20...100/0...100/20...100 RH% (SSR) 0/12 Vc/40 mA output.
Programmable analogue output (optional): 420 mA or 05
V, depending on model.
sensors). Special probes are available on request. Resolution: 1, 0.1 (a resolution of 5 or 0.5 respectively can
also be set).
Accuracy: above 0.5 % of bottom scale.
Power supply (depending on model): 12 Va/c 15%; 230,
115, 24 Va 10%, 50/60 Hz.

56 Analogue output
EWTR 920 EWHR 920
78910 Probe input
8 9 10 8 9 10 8 9 10 7 8 9
920 series
11
1112 Power supply
12
13
PTC Pt100 / Ni100 Pt100 / Ni100 EWHS 280
1315 Relay 1 N.O.
14
7 8 9 10

+
5
15
16
8 9 10 8 9 10 1415 Relay 1 N.C.
6
+ 17
7
8
18 + EWHS 310 1618 Relay 2 N.O.
TcJ / TcK 420 mA
9
10 1718 Relay 2 N.C.
EWPR 930
7 8 9
EWPA 007
EWPA 030
30
EWTR 930
pressure controller

EWTR 930 controllers have two points of intervention with a Casing: plastic, PC+ABS, V0 selfextinguishing.
neutral zone and can be used to Size: front panel 72x72 mm, depth 102 mm.
control temperature (EWTR 930), relative humidity (EWHR
Mounting: panel-mouting; 67x67 mm drilling template.
930), and pressure (EWPR 930). Depending on models, they
may have an input for thermostatic probes (PTC, Ni100, Connections: screw terminals for 2.5 mm2 leads (one lead
Pt100, TcJ, TcK, 420 mA current), humidity probes (EWHS only per terminal), which can be disconnected.
280/300/310) or pressure probes (EWPA 007/030). Operating temperature: 560 C.
The values measured by the probes are displayed with three Storage temperature: 3075 C.
or four digits, depending on models.
A programmable optional 4,20mA or 0...5V output may be
provided as optional, depending on models. Data storage: on permanent memory (EEPROM).
These controllers are available in standard 72x72 mm size Inputs (depending on model): PTC / RTD (Ni100, Pt100) / Tc
with square casing and 230, 115, 24 Va or 12 Va/c. power (J, K) / current (420 mA; Ri = 41 ) for EWTR 930; EWHS
supplies. 280/300/310 for EWHR 930 and EWPA 007/030 for EWPR
930.
Analogue input Range Main outputs: 2 output on 8(3)A 250Va SPDT relay or static
PTC -55...150 (SSR) 0/12 Vc/40 mA output.
Pt100-Ni100 -100...600 / -50...650
Programmable analogue output (optional): 420 mA or
TcJ-TcK 0...600 / 0...999
EWPA 007/030 0,5...0,8 / 0...30 Bar 05 V, depending on the model.
EWHS 280/300/310 20...100/0...100/20...100 RH% Resolution: 1, 0.1 (a resolution of 5 or 0.5 respectively can
also be set).
NOTE: overall range for different kinds of probes (the Accuracy: above 0.5 % of bottom scale.
Power supply (depending on model): 12 Va/c 15%; 230,
sensors). Special probes are available on request.
115, 24 Va 10%, 50/60 Hz.

56 Analogue output
EWTR 930 EWHR 930 78910 Probe input
8 9 10 8 9 10 8 9 10 7 8 9
930 series 1112 Power supply
11
12
PTC Pt100 / Ni100 Pt100 / Ni100 EWHS 280 1315 Relay 1 N.O.
13
14

5
15
7 8 9 10 1415 Relay 1 N.C.
8 9 10 8 9 10
+ 16
6
+
7
17
+ EWHS 310
1618 Relay 2 N.O.
18
8
9
TcJ / TcK 420 mA
1718 Relay 2 N.C.
10
EWPR 930
7 8 9
EWPA 007
EWPA 030
31
EWTR 940
two stage temperature with PID
function controller

EWTR 940 controllers have two points of intervention with Size: front panel 72x72 mm, depth 102 mm
ON/OFF, PD, PID function (on relay 1) and Mounting: panel-mounting with bracket; 67x67 mm drilling
SOFT START function, which can be set on the main output. template
They can be used both for heating and cooling applications.
Connections: screw terminals for 2.5 mm2 leads (one lead
Depending on models they may have an input for
only per terminal), which can be disconnected.
thermostatic PTC, Ni100, Pt100, TcJ, TcK probes or 420
mA current signals. The values measured by the probes are Operating temperature: 560 C.
displayed with three or four digits, depending on models. Storage temperature: 3075 C.
A programmable optional 4,20mA or 0...5V output may be Display: 3 or 4 digits, 12.5 mm high.
provided as optional, depending on models.
These controllers are available in standard 72x72 mm size
with square casing and 230, 115, 24 Va or 12 Va/c power Inputs (depending on model): PTC / RTD (Ni100, Pt100) / Tc
supplies. (J, K) / current (420 mA; Ri = 41 ).
Main outputs: 2 output on 8(3)A 250Va SPDT relay or 0/12
Analogue input Range Vc/40 mA output.
PTC -55...150 Programmable analogue output (optional): 420 mA or 05
Pt100-Ni100 -100...600 / -50...650 V, depending on model.
TcJ-TcK 0...600 / 0...999
Resolution: 1, 0.1 (a resolution of respectively of 5C or
EWPA 007/030 0,5...0,8 / 0...30 Bar
0.5C can be selected).
EWHS 280/300/310 20...100/0...100/20...100 RH%
Accuracy: above 0.5 % of bottom scale.
NOTE: overall range for different kinds of probes (the Power supply (depending on model): 12 Va/c 15%; 230,
range may be limited with specific types of cables, tips and 115, 24 Va 10%, 50/60 Hz.
sensors). Special probes are available on request.

56 Analogue output
7 Output 12 V dc
8 9 10 8 9 10 8 9 10
EWTR 940
8910 Probe input
11
12
PTC Pt100 / Ni100 Pt100 / Ni100 1112 Power supply
13
14 1315 Relay 1 N.O.
15
5 8 9 10 8 9 10
+
6
16 1415 Relay 1 N.C.
+ 17
7
8
18 +
1618 Relay 2 N.O.
TcJ / TcK 420 mA
9
10 1718 Relay 2 N.C.
32
WM 901(/A, /B)

WM 901 controllers have one point of intervention only, are Front panel protection: IP30.
for wall mounting and can be used both Casing: PC+ABS plastic, with a UL94V0 degree of
for heating and cooling applications. They also have a NTC selfextinguishing
thermostatic probe input and a relay output for the
Size: front panel 80x123 mm, depth 25 mm.
management of loads. The values measured by the probes
are displayed with two digits and a sign. The WM 901/A Mounting: on wall.
model has alarm relay output, while the WM 901/B model Connections: on screw terminals for max 2.5 mm2
has a buzzer for the acoustic alarm. conductors (one conductor only per terminal for power
These controllers are available in 80x123 size for wall- connections).
mounting and with 230 Va or 12 Va/c power supplies. Operating temperature: 555 C.
Display: 2 digits plus sign, 12.5 mm high.
Input: NTC probe with reinforced insulation.
Main output: 1 output on 15A 1 hp 250 Va SPDT relay.
Auxiliary output: 1 output on 12 Vc/20 mA max.
Measurement range: 5050C.
Resolution: 1C.
Power supply: 230 Va or 12 Va/c. 10%, 50/60 Hz.

12 Relay N.O.
+
23 Relay N.C.
45 Power supply
67 Output 12 Vc
9 8 7 6 5 4 3 2 1 89 Probe input
WM 901
33
WM 100, 150

WM 100/150 controllers have one point of intervention Casing: plastic, PC+ABS, V0 selfextinguishing.
only, are for wall mounting and can be used both Size: front panel 75x108 mm, depth 49 mm.
for heating and cooling applications. They also have a PTC
Mounting: wall-mounting with fixing screws.
thermostatic probe input and a relay output for the
management of loads. The WM 100 model has no display, Connections: screw terminals for 2,5 mm2 leads (one lead
the WM 150 model displays the values measured by the only per terminal, according to VDE.
probes with two digits. The set point can be adjusted with a regulations).
graduated knob. The two LED's on the WM 100 and the one Operating temperature: 560C.
LED on the WM 150 provide information on the status of
the relay. These controllers are available in 75x108 size, for
wall-mounting, and with 230, 115, 24 Va or 12 Va/c. power Display: 2 digits 10 mm high (for WM 150 only).
supplies. Set point control: selection on graduated scale through a
knob on the front panel.
Intervention differential: adjustable between 0.5 and 10C
(the differential is adjusted through a trimmer placed inside
the casing).
Input: for PTC probe.
Output: 1 output on 8(3)A 250Va SPDT relay.
Accuracy: above 1.5C.
Power supply (depending on model): 12 Va/c. 15% or 24,
115, 230 Va 10%, 50/60 Hz.

12 Probe input
WM 150 67 Relay N.O.

68 Relay N.C.
910 Power supply
1 10
2 9
8
7
6
34
WM 500, 550
one stage, relative humidity controller

WM 500/550 controllers have one point of intervention only Casing: plastic, PC+ABS, V0 selfextinguishing.
and can be used to control relative humidity. Size: front panel 75x108 mm, depth 49 mm.
They also have a EHWS 280/310 humidity probe input and a
Mounting: wall-mounting with fixing screws.
relay output for the management of loads.
The WM 500 model has no display, the WM 550 model Connections: screw terminals for 2,5 mm2 leads (one lead
displays the values measured by the probes with two digits. only per terminal, according to VDE regulations).
The set point can be adjusted with a graduated knob. The Operating temperature: 560C.
two LED's on the WM 500 and the one LED on the WM 550 Storage temperature: 3075C.
provide information on the status of the relay. These
Display: 2 digits 10 mm high (for WM 550 only).
controllers are available in 75x108 size, for wall-mounting,
and with 230, 115, 24 Va or 12 Va/c. power supplies. Set point control: selection on graduated scale through a
knob on the front panel.
Intervention differential: adjustable between 0.5 and 10%RH
(the differential is adjusted through a trimmer placed inside
the casing).
Input: for EWHS 280 probe.
Output: 1 output on 8(3)A 250Va SPDT relay.
Accuracy: above 1% RH.
Power supply (depending on model): 12 Vc 15% or 24,
115, 230 Va 10%, 50/60 Hz.

12 Probe input
67 Relay N.O.
WM 550
68 Relay N.C.
910 Power supply
1 10
2 9
8
7
6
35
3 Temperature Regulators
A series of controllers 3.1 EWTN 970 37

designed to meet all possible 3.2 EWTN 980 38
heating requirements. 3.3 EWTQ 905 39
3.4 EWTQ 915/985 40
Available in two different 3.5 EWTQ 995 41
sizes: with 48x48 mm and
48x96 mm front panel, with
1 or 2 intervention points,
ON/OFF and PID functions.
All units have 1 or 2
intervention points and
configurable PID, SOFT
START and AUTOTUNING
functions.
A set of probes designed to
meet all possible operating
requirements at
temperatures ranging from -
80 and 1200C
36
EWTN 970
single stage regulator for temperature

EWTN 970 controllers are devices with one point of Casing: plastic, ABS UL94V0
intervention, selectable ON/OFF or PID function Size: front panel 48x96 mm, depth 115 mm
and 2 alarm relay outputs, suitable for heating applications.
Mounting: board, bracket fixing; 45.5x92.5 mm drilling
An optional version with 2 control relay
outputs, both usable for the PID function, is also available template
on request. Connections: 6.3 mm Faston terminals
These controllers are available in several models, with 1 Operating temperature: 565C
input for thermostatic Pt100, TcJ, TcK probes or 420 mA
current signals (optional). The values read by the probes are
displayed on a 3 and a half digit displays. Operating humidity: 4080% non condensing
These regulators come in sizes of 48x96 mm with power Display: 3 and a half digits, 7.5 mm high
supplies of 90240 Va, or 2448 Va/c. Inputs: Pt100, Tc (J, K) (all configurable); optional
0/420 mA or 0/15 V input; terminals have goldplated
contacts to improve signal transmission
Heater breaker input (optional): T.A. 100 A/200 mA
Main output C1: 1 output on SPDT 6(2)A 250Va relay or
static (SSR) 0/24 Vc/25 mA output..
Secondary output C2 (optional): 1 output on SPST 6(2)A
250Va relay or static (SSR) 0/24 Vc/25 mA output.
HB Heater breaker output (optional): 1 output on SPST
6(2)A 250Va relay or static (SSR) 0/24 Vc/25 mA output.
Alarms (optional): 2 outputs on SPST, 6(2)A 250Va relay or
static (SSR) 0/24 Vc/25 mA outputs.
Accuracy: 0.5 % (RTD) or 0.7 % (Tc) of bottom scale
Power supply (depending on model): 90240 Va or 2448
Va/c, 50/60 Hz.

1234 Probe input
EWTN 970 1 2 3 4 1 2 3 4 56 Heater breaker input
11 12 78 24 Vc output
10 13
Pt100 / Ni100 Pt100 / Ni100
9 14
+
8 15
1213 Alarm relay 1 N.O.

7 16 AL1
6 17
1214 Alarm relay 2 N.O.
1 2 3 1 2 3
5 18 AL2
4 19 1215 Heater breaker relay N.O.

+
3 20 HB
2 21 TcJ / TcK / TcS 420 mA 1617 Relay 2 N.O.
1 22
C2 1820 Relay 1 N.C.
C1
1920 Relay 1 N.O.

2122 Power supply
37
EWTN 980

EWTN 980 regulators are devices with one point of Casing: plastic, ABS UL94V0
intervention, selectable ON/OFF or PID functions, and 1 (or Size: front panel 48x96 mm, depth 89 mm
2) alarm relay outputs, suitable for heating and cooling
Mounting: board, bracket fixing; 45.5x92.5 mm drilling
applications. These regulators are available in several
models, with Pt100, and Tc (J, K, L, N), thermostatic probe template
inputs. Connections: screw terminals
This model is supplied with 2/3 digit displays. Operating temperature: from 0 to 50C
These regulators come in sizes of 48x96 mm and with
Storage temperature: from 20 to 70C
power supplies of 100240 Va, or 24 Va/c.
Operating humidity: from 20% to 85% RH non condensing
Display: 2 threedigit displays
Inputs: one input for Pt100 and Tc (J, K, L, N) thermostatic
probes
Output C1: 1 output for heating application on SPDT 3A
250Va relay or static (SSR) 0/24 Vc/25 mA output..
Output C2: 1 output for alarm or cooling application on
SPST 6(2)A 250Va relay or static (SSR) 0/24 Vc/25 mA
output.
Output C3: 1 output for 2nd alarm or heater breaker on
SPST 2A 250Va relay or static (SSR) 0/24 Vc/25 mA outputs.
Accuracy: +0.2% bottom scale value + 1 digit @ 25C vs.
ambient temperature
Consumption: 6 VA max.
Power supply: 100240 Va 10%; 24 Vc/a 10%, 50/60 Hz.

1234 Probe input
EWTN 980 1 2 3 4 1 2 3 4 67 T.A. input.
12 1
13 2
1011 Relay 3 N.O.
Pt100 / Ni100 Pt100 / Ni100
14 3
15 + 4
1213 Power supply
16 5
17 6 1415 Relay 2 SSR
1 2 3 1 2 3
18 7
19 + 8 1617 Relay 2 N.O.
+
20 9
21 10 TcJ / TcK / TcS 420 mA 1819 Relay 1 SSR
C2 22 11
2021 Relay 1 N.O.
C1
C3 2022 Relay 1 N.C.
38
EWTQ 905
Single stage temperature regulator

EWTQ 905 regulators are devices with two points of Casing: plastic, ABS UL94 V0
intervention and ON/OFF, PD, PID and SOFT START or Size: front panel 48x48 mm, depth 115 mm
AUTOTUNING functions configurable via the main output,
Mounting: panel-mounting, 45.5x45.5 mm hole
suitable for heating applications. These regulators are
available in several models with 1 input for thermostatic Connections: screw terminals
PTC, Ni100, Pt100, TcJ, TcK probes or 420 mA current Operating temperature: 565C
signals. The values read by the probes are displayed on a 3 Storage temperature: 3075C
digit display.
Display: 3 digits, 7.5 mm high
These regulators come in sizes of 48x48 and with power
supplies of 230/115 Va, or 24 Va/c. Data storage: permanent memory (EEPROM).
Inputs (depending on model): PTC / RTD (Ni100, Pt100) /
Tc (J, K) / current (420 mA; Ri = 41 ); terminals
contacts are goldplated to improve the transmission of
signals
Main output: on SPDT 3(1)A 250Va relay or static (SSR)
0/24 Vc/10 mA relay.
Secondary output: on SPST 3(1)A 250Va relay or static (SSR)
0/24 Vc/10 mA output.
Resolution: 1C or 0.1C with decimal point
Accuracy: 0.5 % greater than bottom scale
Power supply (depending on model): 230/115 Va 10%, 24
Vc/a 10%; 50/60 Hz.

123 Probe input
45 Relay 2 N.O.
1 2 3 1 2 3
EWTQ 905
67 Power supply
89 Relay 1 N.O.
Pt100 / Ni100 Pt100 / Ni100
1 6 810 Relay 1 N.C.
2 7
3 8
4 9 1 2 3 1 2 3
5 10
C2 C1 +
TcJ / TcK 420 mA
39
EWTQ 915, EWTQ 985

EWTQ 915 Front panel protection: IP65.
The EWTQ 915 regulators are devices with one point of Casing: PC+ABS plastic, UL94 V0.
intervention, ON/OFF, PD, PID action, SOFT START and
AUTOTUNING functions, and a relay output for alarm
signalling; they are suitable for applications in hot Mounting: on panel with 45 x 45 mm. hole.
conditions. Connections: on screw terminals.
These regulators are provided with a configurable input for Operating temperature: from 0 to 50 C.
Pt100 and Tc (J, K, N, L, T) thermostatic probes.
Storage temperature: from 20 to 85 C.
The value of the probes reading is viewed on a threedigit
display. They are available in the 48x48 format and the Usage humidity: from 20% to 85% RH noncondensing.
power supply voltage is, on choice, 100240 Va, or 24 Va/c. Display: 3 digits.
Inputs: Pt100 or Tc (L, J, K, N,T) can be entered using the
EWTQ 985 keyboard.
In the EWTQ 985 model, the second output can be set
Output C1: 1 output for heating application on SPDT 3A
either according to an alarm or by setting. This model uses
250Va relay or static (SSR) 0/24 Vc/25 mA output..
a double 3digit display for viewing.
SPST 6(2)A 250Va relay.
Accuracy: +0.3% end of scale value + 1 digit @ 25 C than
the environment temperature.
Power supply: 100240 Va 10%; 24 Va/c 10%, 50/60 Hz.

123 Probe input
1 2 3 45 Relay 2 N.O.
EWTQ 915/985
67 Relay 1 N.C.
Pt100 / Ni100
78 Relay 1 N.O.
6 1
910 Power supply
7 2 1 2 3
8 3
9 4
C1 10 5
Pt100 / Ni100
C2
1 2 3
+
TcJ / TcK
40
EWTQ 995
Two stage temperature regulators

EWTQ 995 regulators are devices with two points of Front panel protection: IP65
intervention; ON/OFF, PD, PID, SOFT START and Casing: gray polycarbonate (RAL 7043), UL 94 V0
AUTOTUNING functions and 1 relay output for alarm
Size: front panel 48x48 mm, depth 100 mm
signalling; suitable for heating applications. These regulators
have a configurable input for Pt100 and Tc (J, K, N, L, T) Mounting: panel-mounting, 45 x 45mm drilling template
thermostatic probes or 0/420 mA current, and 1 digital input. Connections: screw terminals
These regulators come in sizes of 48x48 mm and with Operating temperature: from 0 to 50C
power supplies of 110..240 Va, or 24 Va/c.
Storage temperature: from 20 to 70C
Operating humidity: from 20 % to 85% RH non condensing
Display: 2 fourdigit displays.
Inputs: 1 configurable input for Pt100 and Tc (J, K, N, L, T)
thermostatic probes or 0/420 mA current
Output C1: 1 output for heating/cooling application on
SPDT 3A 250Va relay.
SPST 6(2)A 250Va relay.
Output C3: 1 outputs for 2nd alarm on SPST 2A 250Va relay.
Accuracy: + 0.2% bottom scale + 1 digit @ 25C vs. ambient
temperature
Power supply: 100240 24 Va 10%; 24 Vc/a 10%,
50/60 Hz.

12 Relay 2 N.O.
23 Relay 3 N.O.
8 9 10
EWTQ 995
45 Power supply
67 Relay 1 N.O.
Pt100 / Ni100
6 11 1 8910 Probe input
7 12 2 8 9 10
8 13 3 1415 Digital input or T.A. input
C2
9 14 4
(through Jumper)
C1 10 15 5
C3 Pt100 / Ni100
8 9 10
+
TcJ / TcK
41
4 Timers and Pulse Counters
Timers are available in Timers

standard Eliwell 32x74 mm 4.1 EWPH 480 45
size or with 48x48 mm front 4.2 EWTS 950 46
4.3 EWTS 330/S 47
panel. Both models are
suitable for panel-mounting. Pulse Counters
The timer operating 4.4 EWCH 485 49
parameters can be defined
on all models: type of count
(count-up or countdown),
timing scale, type of
operation, type of action,
function of front panel keys
and I/Os on terminal blocks.
Programmable impulse
counter, 48x48 mm, with
square body.
Options to select type of
action (restart, restart- lap,
count), counting mode (up o
down) , restart time (in
tenths of seconds), max.
counting frequency, counting
division and backup method
(counting storage or reset).
44
EWPH 480
Programmable electronic timer
with 2 inputs and 1 output

EWPH 480 units are programmable electronic timers, Casing: plastic in selfextinguishing ABS
based on a microprocessor, with 1 relay output and 2 Size: front panel 48x48 mm, depth 73 mm
inputs to enable and reset remote counting. Type of
Mounting: panel-mounting (45 x 45mm. hole) with bracket
counting (up or down), timing scale, backup method,
and fixing screws
operating modes and the functions of terminal block reset
and start inputs can be specified by the user. The internal Connections: on screw clamp
battery maintains the timing function even in the event of Operating temperature: 555 C.
power failure. Storage temperature: 3075 C.
Display: 4 digits
Values can be viewed on a 4digit display. These timers
come in sizes of 48x48 with power supplies of 230, 115, 24 Digital inputs: 2 voltage-free digital inputs to enable and
Va or 12 Va/c. reset remote counting
Output: 8(3)A 250Va relay switching contact.
Resolution: 1 digit.
Counting duration (in backup mode): about 5 hours.
Power supply: 12 Va/c 15%; 24, 115, 230 Va 10%.
Time Range: 9999 hours/99 hours, 59 minutes/99 minutes,
59 seconds/9 minutes, 59 seconds and 9 tenths,
programmable by parameter

210 Power supply
EWPH 480 36 Digital input

37 Digital input
111 Relay output N.O.
4 911 Relay output N.C.
3 9
2 1
6 10
7 11
45
EWTS 950
Programmable electronic timer with
2 inputs and 1 output

EWTS 950 units are programmable electronic timers, based Casing: plastic in selfextinguishing ABS
on a microprocessor, with 1 relay output and 2 inputs to Size: front panel 32x74 mm, depth 67 mm
enable and reset remote counting. Type of counting (up or
Mounting: panel-mounting (71 x 29mm hole) with fixing
down), timing scale, backup method, operating modes and
bracket
the functions of terminal block reset and start inputs can be
specified by the user. Connections: on max 4 mm2 screw terminals.
The internal battery enables to continue the timing even in Operating temperature: 555 C.
the event of power failure. Storage temperature: 3075 C.
Values are displayed on a 4digit display. These timers come
Display: 4 digits.
in standard 32x74 size and with a 12 Va/c. power supply.
Inputs: 2 free-voltage digital inputs to enable and reset
remote counting
Output: on 8(3)A 250Va relay switching contact.
Resolution: 1 digit.
Counting duration (in backup mode): about 5 hours
Power supply: 12 Va/c 15%.

EWTS 950 13 Relay output N.C.

56 Power supply
78 Digital input for enabling backup
1 2 3 4 5 6 7 8 9 10 89 Digital input to enable counting
810 Digital input for reset
46
EWTS 330/S
Timer for the management of work cycles

EWTS 330/S is a digital timer, based on microprocessor, EWTS 330/S Technical Data
with a chronoactuator to manage time cycles. It controls 3
Casing: plastic, 70x85 mm DIN rail mounting
relays which can be configured to manage several loads.
Relays are included in the DIN EWTS SLAVE Depth: 61 mm
module that powers the instrument. All input and piloting Mounting: DIN (Omega 3) rail or wall-mounting
signals sent to the module relays and the power supply Protection class: IP50 on front panel
voltage for the EWTS 330/S master pass through the MULTI-
CProtection class: IP50 on front panel Connections:
POLE CABLE. The EWTS 330/S timer has a four digit LED
telephone connector for the connection to the DIN EWTS
display and four keys to manually configure and manage
SLAVE module, screw terminals for 2.5 mm2 leads for digital
loads.
inputs and alarm outputs, RS-485 connection
The timer also has a 12 Vc/20 mA hot output
which can be used to control a fourth relay and manage Viewing: on 3 or 4 digit display, 13 mm high
operating alarms (i.e. back swing after power failure), and 3 Parameter data storage: permanent memory (EEPROM)
inputs to control remote loads. This timer also has a RS485 Operating temperature: 560 C.
port (split to simplify wiring) for the connection to
Operating humidity: 1090% R.H%
TelevisSystem.
EWTS 330/S has an internal clock to manage timing. ge temperature: 3075 C.
The internal backup battery maintains the running of the 12 Vc/20 mA output: hot output for external alarm
timer for at least 1 hour in the event of sudden power management.
failure. EWTS 330/S and EWTS SLAVE timers come in sizes of Digital inputs: 1 free voltage ON/OFF input.
70x85 mm (4 modules) and are suitable to be mounted on
Serial connection: RS485 double port for the connection to
DIN rails (Omega 3) or wall-mounted.
the TelevisSystem.
Power supply: from the EWTS SLAVE module.
EWTS SLAVE Technical Data

Casing: plastic, 70x85 mm DIN rail mounting
Depth: 61 mm.
Mounting: DIN (Omega 3) rails or wall-mounting
Connections: telephone connector for connection to EWTS
330/S and two screw terminals for 2.5 mm2 leads for other
connections
Operating temperature: 560 C.
Environment humidity: 1090% R.H.
Outputs: three (3) 12 Vc/30 mA outputs to pilot the
auxiliary relays of DIN EWTS SLAVE module
Outputs: 1 output on SPST 15(6)A 250Va relay and 2
outputs on SPDT 8(3)A 250Va relay.
Digital inputs: 2 free-voltage ON/OFF inputs
Absorption: 8 VA.
Isolation class: 2.
Power supply: 24, 110, 230 Va, 10%; 50/60 Hz.
47
Wiring Diagram
10 11 12 1 2 3 4
EWTS SLAVE (330) EWTS 330/S
14 15 16 17 19 20 21 22 23 24 13 14 15 16 17 18
gnd + gnd +
Description of Wiring Diagram

EWTS 330/S EWTS SLAVE
12 12 Vc output for alarm 1012 Digital input 1
34 Digital input 3 1112 Digital input 2
131415 RS485 serial output for connection 1415 Relay output 2 N.C.
to TelevisSystem
1416 Relay output 2 N.O.
161718 RS485 serial output for connection
to TelevisSystem
2122 Relay output 3 N.C.
2324 Power supply
48
EWCH 485
Electronic programmable
pulse counter

EWCH 485 units are electronic programmable pulse counters, Casing: plastic, in ABS UL 94 V0
based on microprocessor, with 1 relay output, 1 input to Size: front panel 48x48 mm, depth 73 mm Mounting: panel-
receive the counting signal and 2 inputs to enable and reset mounting (45 x 45 mm hole) with bracket and fixing screws,
remote counting. Type of action (restart, restart lap, drilling template Connections: screw terminals
counting), type of counting (up or down), restart time (in
tenths of seconds), maximum counting frequency, counting
ratio and backup method (storage or counting reset) can be Storage temperature: 3075 C.
specified by the user. Display: 4 digits.
Inputs: 3 separate inputs for counting and to enable and
Values are displayed on a 4digit display. These counters reset remote counting (voltage free contacts)
come in sizes of 48x48 with power supplies of 230, 115, 24
Output: 8(3)A 250Va SPDT relay.
Va or 12 Va/c.
Power supply: 12 Va/c 15%; 24, 115, 230 Va 10%.

210 Power supply
35 Impulse digital input
EWCH 485
36 Digital input for reset
2
3 37 Digital input to enable counting
4 38 12 Vc output
5 9
6 1
7 10 911 Relay output N.C.
+
8 11
49
5 Controllers
for refrigeration
The new ID and IS products, Digifrost Line

in standard 32x74 Eliwell 5.1 ID 961 ID 961 LX 52
size, are suitable for all 5.2 ID 970 ID 970 LX 53
5.3 ID 971 ID 971 LX 54
models of refrigerating units
5.4 ID 974 ID 974 LX 55
and also for the most 5.5 ID 975 LX 56
advanced plant controllers. 5.6 ID 983LX - ID985 LX 57
The availability of a series of 5.7 IS 972 LX with EWEM 233 Slave module 59
specific algorithms guarantee 5.8 IS 974 LX with EWEM 243 Slave module 61
an excellent preservation of
Defrost Timers and
fresh and deep frozen food, Blind Controllers for Refrigeration
along with efficient 5.9 EWTS 70 63
refrigerating system and low 5.10 EWTS 72 64
energy consumption. 5.11 EWTS 90 65
5.12 EWLC 74 66
By connecting the devices to
TelevisSystem, it is also 5.13 EWDR 981 67
possible to remotely manage 5.14 EWDR 983 /C /CS LX 68
the installations. 5.15 EWDR 984 69
5.16 EWDR 985 /CS LX 71
The range also includes
special controllers for 5.17 IWC 720 73
commercial refrigeration, 5.18 IWC 730 74
which are particularly 5.19 IWC 740 75
suitable for all those 5.20 IWC 750 76
applications that require a
5.21 IWP 740 LX 77
high degree of 5.22 IWP 750 LX, IWP 760 LX 79
personalization in terms of 5.23 IWP 985 LX /CS LX 81
service, operation and
flexibility. EWPC 1000
5.24 EWPC 1000(/C, /S) 83
50
5 Controllers
for refrigeration
EWTB 1000
5.25 EWTB 1000(/C, /S) 85
Compressor Control
5.26 EWCM 400 (412 415 418) 87
5.27 EWCM 800 89
5.28 EWCM 900 91
5.29 EWCM 809/NH3/S 93

5.30 WM 961 (/A, /B) 31

5.31 EWFC 1000 95
5.32 MT6 96
Fans Controllers
5.33 FASEC 33 97
5.34 FASEC 43/43C 98
5.35 FASEC 53 99
5.36 FASEC 100 100
5.37 FASEC 500 101
5.38 WM 203 102
5.39 WM 253 103
51
ID 961, ID 961 LX
Electronic controller for static
refrigerating units

ID 961 Front panel protection: IP65
ID 961 controllers that can be fitted on refrigerating units Casing: plastic, PC + ABS, UL94 V-O
operating at normal temperature.
They have a PTC thermostatic probe input (the NTC input
can be selected with a parameter) and a relay output to Mounting: panel-mounting with 71x29 mm (+0,2/-0,1 mm)
manage compressors. Defrost cycles are controlled at timed drilling template
intervals by stopping the compressor. Operating temperature: -555C
The values measured by the probes are displayed with two Storage temperature: -3085C
digits and a minus sign.
Operating and storage environment humidity: 1090 % RH*
All models have TTL connections that enable the controllers
to be used with the Copy Card, the quick programming *(non condensing)
accessory. Display: oID 961: 2 digits and minus sign
The 16 A compressor relay options and the buzzer are also ID 961LX: 3-digit and a half and minus sign
provided. These controllers are available in standard 32x74
Analogue inputs: a PTC or NTC input (configurable by
standard size and with 230 Va or 12 Va/c power supplies.
means of a parameter).
ID 961 LX HACCP
The range also includes models that are able to manage and Digital inputs: 1 configurable low voltage digital input (LX
store the alarms, in compliance with the HACCP models)
requirements. Serial: TTL for Copy Card connection and TelevisSystem (LX
models).
Digital outputs: 1 output on SPDT 8 (8)A 250Va relay
Resolution: 1C (base models) or 0,1C (LX models)
Consumption: 3 VA.
Power supply: 230 Va or 12 Va/c 10%, 50/60 Hz.
NTC 50110,0
PTC 55150,0 Warning: check the power supply specified on the
Wiring Diagram
A
Common ID 961 LX
ID 961 - 12 V
12 Compressor relay N.C. 810 Digital input
13 Compressor relay N.O. A TTL input for
67 Power supply Copy Card and

1 2 3 6 7 8 9 10
TelevisSystem
89 Probe input
ID 961 - 230 V A
1 2 3 6 7 8 9 10
52
ID 970, ID 970 LX
refrigerating units

ID 970 Front panel protection: IP65
ID 970 controllers that can be fitted on refrigerating units Casing: plastic, PC + ABS, UL94 V-O
operating at normal or low temperature.
can be selected with a parameter) and two relay outputs to Mounting: panel-mounting, with 71x29 mm (+0,2/-0,1 mm)
manage compressors and defrost. Defrost cycles are drilling template
controlled at timed intervals by stopping the compressor. Operating temperature: -555C
The values measured by the probes are displayed with three Storage temperature: 3085 C.
digits and a minus sign. All models have TTL connections
Operating and storage environment humidity: 1090 % RH
that enable the controllers to be used with the Copy Card,
the quick programming accessory. (non condensing).
The 16 A compressor relay options and the buzzer are also Display: 3-digit and a half with minus sign.
provided. These controllers are available in standard 32x74 Analogue inputs: a PTC or NTC input selectable with
standard size and with 230 Va or 12 Va/c power supplies. parameter.
Digital Inputs: 1 configurable low voltage digital input (LX
ID 970 LX
models).
The LX version, usually supplied for NTC probe can also be
connected to TelevisSystem to allow values to displayed Serial: TTL for Copy Card connection and TelevisSystem (LX
with three digits and a minus sign. The decimal point and models).
digital input are programmable. Digital outputs: 2 outputs: on SPDT 8(3)A 250Va relay and
on SPST 8(3)A 250Va relay
Probe Measurement range (C) Resolution: 1 or 0,1 C.
NTC 50110,0 Accuracy: above 0.5% of bottom scale + 1 digit.
PTC 55150,0
Consumption: 3 VA.

Wiring Diagram instrument label: contact the Sales Office for further
ID 970 - 12 V A Description of Wiring Diagram

Common ID 970 LX
1 2 3 4 5 6 7 8 9 10 11 12 Defrost relay N.O. 811 Digital input

13 Defrost relay N.C. A TTL input for
45 Compressor relay output Copy Card and
67 Power supply TelevisSystem
810 Probe input
ID 970 - 230 V A A TTL input for Copy Card
1 2 3 4 5 6 7 8 9 10 11
53
ID 971, ID 971 LX
refrigerating units

ID 971 Front panel protection: IP65.
ID 971 controllers that can be fitted on refrigerating units Casing: plastic, PC + ABS, UL94 V-O.
operating at normal or low temperature.
can be selected with a parameter) and two relay outputs to Mounting: panel, with 71x29 mm (+0,2/0,1 mm) drilling
manage compressors and defrost. Defrost cycles can be template.
stopped at a specific time or as soon as the end cycle Operating temperature: 555 C.
temperature is reached (if the evaporator is equipped with Storage temperature: 3085 C.
a specific probe).
Operating and storage environment humidity: 1090 % RH
(noncondensing).
digits and a minus sign.
The decimal point can be set with a parameter. All models Display: 3digit and a half with a minus sign.
have TTL connections that enable the controllers to be used Analogue inputs: two PTC or NTC inputs selectable with
with the Copy Card, the quick programming accessory. parameter.
The 16 A compressor relay options and the buzzer are also Digital Inputs: 1 configurable low voltage digital input (LX
provided. These controllers are available in standard 32x74 models).
standard size and with 230 Va or 12 Va/c power supplies.
Serial: TTL for Copy Card and TelevisSystem (LX models).
ID 971 LX Digital outputs: 2 outputs: on SPDT 8(3)A 250Va realy and
The LX version, usually supplied for NTC probe, can also be on SPST 8(3)A 250Va relay.
connected to TelevisSystem or, alternatively to ModBUS Accuracy: above 0.5% of bottom scale + 1 digit.
networks, and has a programmable digital input. Resolution: 1 or 0,1 C.
Consumption: 3 VA.
NTC 50110,0 Power supply: 230 Va or 12 Va/c 10%, 50/60 Hz.
PTC 55150,0

Wiring Diagram instrument label: contact the Sales Office for further
ID 971 - 12 V A
Common ID 971 LX
1 2 3 4 5 6 7 8 9 10 11 12 Defrost relay N.O. 811 Digital input

TelevisSystem
67 Power supply
89 Probe 2 input
ID 971 - 230 V A
810 Probe 1 input
1 2 3 4 5 6 7 8 9 10 11
54
ID 974, ID 974 LX
Electronic controller for ventilated
refrigerating units

ID 974 Front panel protection: IP65.
ID 974 controllers can be fitted on ventilated refrigerating Casing: plastic, PC + ABS, UL94 V-O.
units operating at normal or low temperature.
They have two PTC thermostatic probe inputs (the NTC
input can be selected with a parameter) and three relay Mounting: panel-mounting, with 71x29 mm (+0,2/-0,1 mm)
outputs for the management of the compressors, the drilling template.
defrost and evaporator's fans. Operating temperature: 555 C.
Defrost cycles can be stopped at a specific time or as soon Storage temperature: 3085 C.
as the end cycle temperature is reached (if the evaporator
Operating and storage environment humidity: 1090 % RH*
is equipped with a specific probe). The values measured by
the probes are displayed with three digits and a minus sign. (non condensing).
The decimal point can be set with a parameter. All models Display: 3-digit and a half with minus sign.
have TTL connections that enable the controllers to be used Analogue inputs: two PTC or NTC inputs selectable with parameter.
with Copy Card, the quick programming accessory. These
Digital Inputs: 1 configurable low voltage digital input (LX
controllers are available in standard 32x74 size with 230 Va
models).
or 12 Va/c power supplies.
ID 974 LX Serial: TTL for Copy Card connection and TelevisSystem (LX
The LX version, usually supplied for NTC probe, can also be models).
connected to TelevisSystem and has a Digital outputs: 3 outputs: on SPDT 8(3)A 250Va realy, on
programmable digital input. SPST 8(3)A 250Va relay, and on SPST 5(2)A 250Va.
ID 974 LX HACCP Resolution: 1 or 0,1 C.
The range also includes models that are able to manage and
store the alarms, in compliance with the HACCP
requirements. Consumption: 3 VA.
Probe Measurement range (C) Warning: check the power supply specified on the
NTC 50110,0 instrument label: contact the Sales Office for further
PTC 55150,0 information on relay capacity and power supply.

Common ID 974 LX
ID 974 - 12 V A
12 Defrost relay N.O. 811 Digital input

1 2 3 4 5 6 7 8 9 10 11 TelevisSystem
15 Fan relay output
67 Power supply
89 Probe 2 input
810 Probe 1 input
ID 974 - 230 V A A TTL input for Copy Card
1 2 3 4 5 6 7 8 9 10 11
55
ID 975 LX
refrigerating units with programmable
outputs

ID 975 LX controllers can be fitted on ventilated Front panel protection: IP65.
refrigerating units operating at normal or low temperatures. Casing: plastic, PC + ABS, UL94 V-O.
They have two inputs for NTC (the PTC can be set with a
parameter) thermostatic probes and four relay outputs to
manage the compressors, defrost, evaporator's fans and Mounting: panel-mounting, with 71x29 mm (+0.2/-0.1 mm)
alarms (or auxiliary loads like lights). drilling template.
The buzzer is optional. Operating temperature: 555 C.
Defrost cycles can be stopped at a specific time or as soon Storage temperature: 30.85 C.
Operating environment humidity: 1090 % RH*
is equipped with a specific probe).
The values measured by the probes are displayed with three Storage environment humidity: 1090% RH*
digits and a minus sign. The decimal point can be set with a *(non condensing).
parameter. Display: 3-digit and a half with minus sign.
All models have TTL connections that enable the controllers
Analogue inputs: two PTC or NTC inputs configurable by
to be used with Copy Card, the quick programming
means of a parameter.
accessory.
These controllers are available in standard 32x74 size with Serial: TTL for TelevisSystem or a Copy Card.
12 Va/c power supplies. Digital outputs: 4 outputs on relay, the first and second
outputs are SPST 8(3)A 250Va, the third and fourth outputs
are SPST 5(2)A 250Va.
Resolution: 1 or 0.1 C.
NTC 50110,0
PTC 55150,0 Accuracy: above 0.5% of bottom scale +1 digit
Consumption: 3 VA.
Power supply: 12 Va/c 10%, 50/60 Hz.

123 Defrost relay output
124 Compressor relay output
ID 975 LX A
125 Fan relay output
126 Alarm relay output
78 Power supply
1 2 3 4 5 6 7 8 9 10 11 910 Probe 2 input

911 Probe 1 input
A TTL input for Copy Card and for TelevisSystem
56
ID 983 LX - 985 LX
Electronic controller for refrigerating units
with programmable outputs, specifically
designed for supermarkets

ID 983/985 LX controllers can be fitted on ventilated Front panel protection: IP65
refrigerating units operating at normal or low temperature. Casing: plastic, PC + ABS, UL94 V-O
They are have three outputs for NTC (the PTC output can
be set with a parameter) thermostatic probes that can be
used to control temperature, manage the defrost cycle and Mounting: panel-mounting, with 71x29 mm (+0.2/-0.1 mm)
display additional temperature values (or the defrost cycle drilling template
on the second evaporator). Operating temperature: -555C
The four relay outputs (two for ID983LX) can be used to Storage temperature: -3085C
manage compressors, the defrost cycle, the evaporator's
Operating environment humidity: 1090 % RH*
fans and the alarms; the alarm relay can also be configured
to manage auxiliary loads like lights. Storage environment humidity: 1090% RH* *(non
The buzzer is optional. condensing)
The two additional programmable digital inputs can be used Display: 3-digit and a half with minus sign
as door switches or to remotely enable the defrost cycle, Analogue inputs: three PTC or NTC inputs (configurable by
the minimum threshold, an auxiliary load or an alarm signal. means of a parameter)
Defrost cycles can be stopped at a specific time or as soon
Digital inputs: 2 voltage-free digital inputs configurable by
means of a parameter
The values measured by the probes are displayed with three Serial: TTL for TelevisSystem or a Copy Card
digits and a minus sign. Digital outputs: 4 outputs on relay (2 outputs for ID983LX):
The decimal point can be set with a parameter. Models /C first output SPDT 8(3)A 250Va, second and third outputs
and /CK also have clock and LINK functions to manage the SPST 8(3)A 250Va, fourth outputs SPST 5(2)A 250Va
defrost and other weekly events. All models have TTL Output for Link network
connections that enable the controllers to be used with the
Resolution: 1 or 0.1C
Copy Card, the quick programming accessory, or for the
connection to TelevisSystem or alternatively to ModBUS Accuracy: above 0.5% of bottom scale +1 digit
networks. Consumption: 3 VA.
These controllers are available in standard 32x74 size with
12 Va/c power supplies.
ID 983 - 985 LX HACCP
store the alarms, in compliance with the HACCP
requirements.
ID 983-985 LX HACCP with Annual Calendar
There is also a model with HACCP function that enables to
manage yearly events.

NTC 50110,0
PTC 55150,0
57
Wiring Diagram
1 2 3 4 5 6 7 8 9 10 11 A
12 13 14 15 16 17 18 19 ID 983/985 LX
ONLY 985 LX

12 Probe 1 input 1011 Power supply
13 Probe 2 input 1213 Defrost relay N.O.
14 Probe 3 input 1214 Defrost relay N.C.
56 Digital input 1 1516 Compressor relay output
57 Digital input 2 1517 Fan relay output (ID985LX model only)
8 Link connection 1819 Alarm relay output (ID985LX model only)
9 Link + connection A TTL input for Copy Card and connection
to TelevisSystem
58
IS 972 LX
refrigerating units

IS 972 LX controllers can be fitted on ventilated IS 972 LX
refrigerating units operating at normal or low temperatures.
Front panel protection: IP65
These controllers have a master unit and a power slave unit
(EWEM 233, to be ordered separately) that are connected Casing: plastic, PC + ABS, UL94 V-O
to one another by means of a multipolar cable with quick Size: front panel-mounting 32x74 mm, depth 30 mm
coupling. The power unit has two inputs for NTC (the PTC Mounting: panel-mounting, with 71x29 mm (+0.2/-0.1 mm)
probe can be selected with a parameter) temperature drilling template
probes and three relay outputs to manage the compressors,
Operating temperature: -555C
defrost cycle and evaporator's fans.
Defrost cycles can be stopped at a specific time or as soon Storage temperature: -3085C
as the end cycle temperature is reached (if the evaporator Operating humidity: 1090 % RH (non condensing)
is equipped with a specific probe). The master unit with a Storage humidity: 1090% RH (non condensing)
programmable digital input, enables to display the values
Display: 3-digit and a half with minus sign
measured by probes with three digits a minus sign.
The decimal point can be set with a parameter. Digital input: 1 low voltage configurable digital input
The buzzer is optional. Serial: TTL for TelevisSystem or Copy Card
All models have TTL connections that enable the controllers Resolution: 1 or 0.1C
to be used with the Copy Card, the quick programming
accessory, or for the connection to TelevisSystem or
alternatively to ModBUS networks. Power supply: from EWEM Slave module
These controllers are available in standard 32x74 split size
with 230 Va power supplies. EWEM 233
Probe Measurement range (C) Casing: plastic, 4 DIN modules
NTC 50110,0
PTC 55150,0
Mounting: on DIN (Omega 3) rail or wall-mounting
Connections: telephone receptacle for connection to the IS
main module as well as to screw terminals for other
connections
Storage temperature: -3075C
Analogue inputs: two inputs PTC or NTC (configurable by
means of a parameter, accessible from the display on the IS
main module)
Digital outputs: 1 output on SPST relay for 15(12)A 250Va, 1
output on SPDT relay 10(7)A 250Va and 1 output on SPST
relay 16(8)A 250Va (configurable)
Consumption: 3 VA.
Power supply: 230 Va 10%, 50/60 Hz.
59
Wiring Diagram
IS 972 LX
B A
to EWEM 233
Module
3 4 1 2 3 4 5 6 11 12
EWEM 233
to 972 LX
module
16 17 18 22 24

IS 972 LX EWEM 233
34 Digital input 12 Relay output 2 N.O.
A TTL serial input for Copy Card and connection 46 Relay output 3 N.C.
to TelevisSystem 56 Relay output 3 N.O.
B ISEWEM Connection 1112 Power supply
1618 Input for PTC or NTC probe
B ISEWEM connection
60
IS 974 LX
Electronic controller for refrigerating units
with programmable outputs

IS 974 LX controllers can be fitted on ventilated IS 974 LX
refrigerating units operating at low or normal temperatures.
Front panel protection: IP65
These controllers have a master unit and a power slave unit
(EWEM 243, to be ordered separately) that are connected Casing: plastic, PC + ABS, UL94 V-O
to one another by means of a multipolar cable with quick Size: front panel 32x74 mm, depth 30 mm
coupling. The power unit has two inputs for NTC (the PTC Connections: telephone receptacle for EWEM expansion
probe can be selected with a parameter) temperature module and screw terminals for other connections
probes and four relay outputs to manage the compressors,
Mounting: panel-mounting, with 71x29 mm (+0.2/-0.1 mm)
defrost cycle, evaporator's fans and alarms. The alarm relay
drilling template
can also be configured to manage external loads like lights.
Defrost cycles can be stopped at a specific time or as soon Operating temperature: -555C
as the end cycle temperature is reached (if the evaporator Storage temperature: -3085C
is equipped with a specific probe). The master unit with a Operating environment humidity: 1090% RH (non
programmable digital input, enables the display of values condensing)
measured by probes with three digits a minus sign. The
Storage environment humidity: 1090% RH (non
decimal point can be set with a parameter. The buzzer is
condensing)
optional. All models have TTL connections that enable the
controllers to be used with the Copy Card, the quick Display: 3-digit and a half with minus sign
programming accessory, or for the connection to Digital input: 1 low voltage configurable digital input
TelevisSystem. Serial: TTL for TelevisSystem or a Copy Card
The master unit is available in the 32x74 split size while the
Resolution: 1 or 0.1C
power slave unit in the 4 module DIN size.
All models have a 230 Va power supply. Accuracy: above 0.5% of bottom scale + 1 digit
Power supply: from EWEM Slave module

NTC 50110,0 EWEM 243
PTC 55150,0 Casing: plastic, 4 DIN modules
Mounting: on DIN (Omega 3) rail or wall-mounting
Connections: telephone receptacle for IS main module and
screw terminals for other connections
Analogue inputs: two inputs PTC or NTC (configurable by
means of a parameter, accessible from the display on the IS
main module)
Digital outputs: 1 output on SPST relay for 15(12)A 250Va, 1
output on SPDT relay 10(7)A 250Va and 2 outputs on SPST
relay 8(3)A 250Va (configurable)
Consumption: 3 VA.
61
Wiring Diagram
IS 974 LX
B A
to EWEM 243
Module
3 4 1 2 3 4 5 6 11 12
EWEM 243
to 974 LX
module
16 17 18 22 24

IS 974 LX EWEM 243
34 Digital input 12 Relay output 4 N.O.
A TTL serial input for Copy Card and connection 23 Relay output 3 N.O.
to TelevisSystem 24 Relay output 3 N.C.
B ISEWEM Connection 56 Relay output 2 N.O.
1112 Power supply
B ISEWEM Connection
62
EWTS 70
Electronic defrost timers

EWTS 70 electronic defrost timers can be fitted on all types Front panel protection: IP65 (on request, a shelter (roofing
of refrigerating systems. These timers have an output relay tile) with restrained mounting on the back of the
to manage the defrost cycle and a digital input for the instrument is supplied in order to protect the screw
connection of the Klixon thermostat. terminals)
The defrost cycle can be controlled by setting a timeout or
Casing: plastic resin, PC+ABS, UL-94 V0
via the Klixon thermostat; the time intervals
between the defrost cycles (from 4 to 28 hours with steps Size: front panel 32x74 mm, depth 67 mm
of 4 hours) and the defrost duration (from 5 to 60 Mounting: panel-mounting with a bracket (supplied), 71x29
minutes on two different set up scales) are also mm hole
configurable. Connections: screw terminals for max. 2,5 mm2 connectors
Defrost can be enabled manually by pressing the related
button on the front panel.
The timers are available in the 32x74 standard size with a 12 Storage temperature: -3075C
Va/c power supply. Data storage: permanent memory (EEPROM).
Time interval between defrost cycles*: from 4 to 28 hours in
steps of 4 hours
Defrosting time*: from 5 to 60 minutes, with two scales
(5' - 30' and 30' - 60').
Digital input: 1 input for external Klixon thermostat.
Outputs: 1 free-voltage output on SPDT 8(3)A 250Va relay
Consumption: 1 VA max
* By means of a dip-switch and trimmer

12 Power supply
34 Digital input for klixon thermostat
56 Defrosting relay output N.O.
EWTS 70 67 Defrosting relay output N.C.
6 5 7 1 2 3 4
63
EWTS 72
Electronic defrost timer

EWTS 72 electronic defrost timers can be fitted on all types Front panel protection: IP65 (on request, a shelter (roofing
of refrigerating systems. These timers have an output relay tile) with restrained mounting on the back of the
to manage the defrost cycle, and output relay to stop the instrument is supplied in order to protect the screw
fans while the defrost is in progress and a digital input for terminals).
NTC temperature control probes. Casing: PC+ABS resin plastic, UL-94 V0.
is equipped with a specific probe). Mounting: panel-mounting with a bracket (supplied), 71x29
The intervals between the defrost cycles (from 2 to 30 mm hole.
hours in steps of 2 hours) can be configured. Connections: on screw terminals for conductors max 2,5 mm2
The timers are available in the 32x74 standard size with a Operating temperature: -560C
12 Va/c power supply.
Data storage: permanent memory (EEPROM).
Time interval between defrost cycles*: from 2 to 30 hours in
steps of 2 hours.
Defrosting end temperature*: adjustable between 315C.
Defrost forced stop: after 1/2 hour or after 1 hour
(depending on the model).
Defrost output: on SPDT 8(3)A 250Va relay.
Fan use delay: adjustable from 1 to 8 minutes.
Inputs: 1 input for NTC probe.
Outputs: on SPDT 8(3)A 250Va relay and on SPST 8(3)A
250Va relay.
Accuracy: depending on the power supply rate; 1,5% max
with direct current power supply.
Power supply: 12 Va/c 10, 50/60 Hz.
* By means of a dip-switch and trimmer

12 Power supply
34 Input for NTC probe
67 Fans relay output N.O.
EWTS 72 89 Defrosting relay output N.O.
910 Defrosting relay output N.C.
9 8 10 6 7 1 2 3 4
64
EWTS 90
Electronic defrost timer

EWTS 90 electronic defrost timers can be fitted on Front panel protection: IP65 (on request, a shelter (roofing
refrigerating units with heat pumps. They have a relay tile) with restrained mounting on the back of the
output to manage the defrost cycle and an input for NTC instrument is supplied in order to protect the screw
thermostatic probes. terminals).
Defrost cycles can be stopped at a specific time or as soon Casing: plastic resin, PC+ABS, self-extinguishing, UL-94V0.
The intervals between the defrost cycles (from 15 to 105 Mounting: panel-mounting with bracket (supplied), 71x29
minutes in steps of 15 minutes) and the defrost duration mm hole.
(from 10 to 15 minutes) can be configured. Connections: screw terminals for max. 2.5 mm2 connectors.
Defrost can be enabled manually by pressing the related Operating temperature: -560C.
button on the front panel.
Storage temperature: -3075C.
The timers are available in the 32x74 standard size with a 12
Va/c power supply. Data storage: permanent memory (EEPROM).
Defrost cycle end: by means of NTC probe on evaporator.
Defrost forced stop: 10 or 15 minutes, settable with
microswitch 1.
Defrost end temperature: adjustable, 1020C.
Defrost start temperature: adjustable, -55C.
Inputs: 1 input for NTC probe.
Outputs: 1 output on SPDT 8(3)A 250Va relay for the
defrost system.
Power supply: 12 Va/c 10, 50/60 Hz.

67 Power supply
89 Input for NTC probe
EWTS 90 13 Defrosting relay output N.C.
1 2 3 6 7 8 9
65
EWLC 74
Blind electronic controller for static
refrigerating units

EWLC 74 blind controllers can be fitted on refrigerating Protection: (on request, a shelter (roofing tile) with
units operating at normal or low temperature. They have restrained mounting on the back of the instrument is
two inputs for NTC temperature probes and two relay supplied in order to protect the screw terminals).
outputs to manage the compressors and the defrost cycle. Casing: plastic resin, PC+ABS, UL-94 V0.
is equipped with a specific probe). Connections: on screw terminals for max. 2,5 mm2
A series of parameters, preset by the manufacturer, enable connectors.
the instruments to be configured depending on the Mounting: panel-mounting, 29x71 mm hole.
application. Several LEDs on the front panel provide Data storage: permanent memory (EEPROM).
information on the operating status.
Operating temperature: -560C.
The controllers are available in the 32x74 standard size with
a 230 Va power supply. Storage temperature: -3075C.
Analogue inputs: two NTC probes to adjust temperature
and manage the defrost cycle.
Outputs: 1 output on SPST relay for 8 (3)A 250Va
compressor and 1 output on SPDT 8 (3)A 250Va relay for
the defrosting system.

67 Power supply
89 Defrosting probe input
810 Thermostat probe input
EWLC 74
1 2 3 4 5 6 7 8 9 10 45 Compressor relay output N.O.
66
EWDR 981
electronic controller for static refrigerating
units

EWDR981 controller has two analogue inputs for NTC Casing: plastic, 4 DIN module.
temperature probes (parameter selectable PTC) and a digital
Dimensions: front panel 70x85 mm, depth 61mm.
relay output for the compressor. It also has a configurable
12V-20 mA output that can be configured to manage Mounting: DIN rail mounting (Omega 3) or wall-mounting.
additional loads like alarms. Defrost cycle can be controlled Connections: screw terminals for 2.5mm2 leads (one lead
by stopping the compressor. The two analogue inputs are
per terminal for power connections).
used for temperature control or display purposes.
Operating temperature: -5...55C.
The values measured by the probes are displayed with three Storage temperature: -30...85C.
digits and a minus sign. The decimal point can be set with a
parameter. The buzzer is optional. Operating and storage humidity: 10...90 %RH (non
All models have TTL connections that enable the condensing).
controllers to be used with the Copy Card, the quick Display: 3 digits and a half + sign.
programming accessory.
Analogue inputs: 2 voltage free digital inputs configurable
by means of a parameter.
All models have two voltage-free programmable Serial: TTL for Copy Card.
digital inputs.
The power supply is 230Va. Digital outputs: 1 digital output on 16A relay 1hp 250V SPDT.
Configurable 12Vc/20mA output.
Resolution: 1 or 0.1C.
Accuracy: above 0.5% of bottom scale +1 digit.
Consumption: 5VA.
Power supply: 230Va.

1-2 Probe 1 8-9* Alarm Output/
1-3 Probe 2 13-14 Power Supply 230Va
1-4 Probe 3 19-22* Compressor relay N.O.
+ -
5-6 Digital input 1 20-21* Compressor relay N.C.
5-7 Digital input 2
1 2 4 5 6 7 8 9 10 11 12
To TTL input for Copy Card
A
TTL
EWDR981 * Configurable by means of a parameter
13 14 19 20 21 22 23
67
EWDR 983 (/C/CS LX)
electronic controller for static
refrigerating units

The EWDR983 controller has three analogue inputs for NTC Casing: plastic, 4 DIN module.
temperature probes (parameter selectable PTC) and two
digital relay outputs for the compressor and defrosting. This
controller also has a configurable 12V-20mA output to Mounting: DIN rail mounting (Omega 3) or wall-mounting.
manage additional loads like alarms. Defrost cycles can be Connections: screw terminals for 2.5mm2 leads (one lead
stopped at a specific time or as soon as the end cycle
temperature is reached (if the evaporator is equipped with a
specific probe). The three analogue inputs can be used for Operating temperature: -5...55C.
temperature control, to manage the defrost cycle and to Storage temperature: -30...85C.
display the related values (or to manage the defrost cycle of
the second evaporator). Operating and storage humidity: 10...90 %RH (non condensing).
The values measured by the probes are displayed with three Display: 3 digits and a half + sign.
digits and a minus sign. The decimal point can be set with a
parameter. The buzzer is optional. Analogue inputs: 3 voltage free digital inputs configurable
All models have TTL connections that enable the by means of a parameter.
controllers to be used with Copy Card, the quick
Serial: TTL for Copy Card.
programming accessory.
RS485 for TelevisSystem.
EWDR983/C
Digital outputs: 2 digital outputs on relay; 8A 1/2hp 250V
The /C models also have:
an internal clock (RTC) to manage the defrost cycle and the SPDT; 16A 1hp 250V SPDT
night and day function. Configurable 12Vc/20mA output.
EWDR983/CS LX
The /CS LX models also have:
an internal clock (RTC) to manage the defrost cycle and the Accuracy: above 0.5% of bottom scale +1 digit.
night and day function. Consumption: 5VA.
an internal opto-insulated RS485 internal connection and
can be connected to TelevisSystem. Power supply: 230Va.
All models have two voltage-free programmable
digital inputs.
The power supply is 230Va.

1-2 Probe 1 10-12 RS485 network
1-3 Probe 2 13-14 Power supply 230Va
1-4 Probe 3 17-18* N.O. Defrost relay
RS 485 5-6 Digital input 1 17-19* N.C. Defrost relay
+ - + - GND
5-7 Digital input 2 20-21 *N.O. Compressor relay
1 2 3 4 5 6 7 8 9 10 11 12
8-9* Alarm output / 22-23 *N.C. Compressor relay
A A TTL input for Copy Card
TTL
EWDR983/CS LX
* Configurable by means of a parameter
13 14 15 16 17 18 19 20 21 22 23
68
EWDR 984
electronic controller for ventilated
refrigerating units

temperature probes (parameter selectable PTC) and three
digital relay outputs to manage the compressors, defrost
cycle and the fans. Mounting: DIN rail mounting (Omega 3) or wall-mounting.
This controller also has a configurable 12V-20mA Connections: screw terminals for _2.5mm2 leads (one lead
output to manage additional loads like alarms.
Defrost cycles can be stopped at a specific time or as soon as
the end cycle temperature is reached (if the evaporator is Operating temperature: -5...55C.
equipped with a specific probe). The three analogue inputs Storage temperature: -30...85C.
can be used for temperature control, to manage the defrost
cycle and to display the related values (or to manage the Operating and storage humidity: 10...90 %RH (non
defrost cycle of the second evaporator). condensing).
Display: 3 digits and a half + sign.
digits and a minus sign. The decimal point can be set with a Analogue inputs: 3 voltage free digital inputs configurable
parameter. The buzzer is optional. by means of a parameter.
All models have TTL connections that enable the Serial: TTL for Copy Card.
controllers to be used with Copy Card, the quick
programming accessory. Digital outputs: 3 digital outputs on relay: 8A 1/2hp 250V
SPST;
8A 1/2hp 250V SPDT; 16A 2hp 250V SPDT.
digital inputs.
The power supply is 230Va. Configurable 12Vc/20mA output.
Accuracy: above 0.5% of bottom scale +1 digit.
Consumption: 5VA.

1-3 Probe 2 15-16* N.O. Fan relay
1-4 Probe 3 17-19* N.C. Compressor relay
5-6 Digital input 1 18-19* N.O. Compressor relay
+ -
5-7 Digital input 2 20-22* N.O. Compressor relay
8-9* Alarm output / 20-22*N.C. Defrost relay
1 2 3 4 5 6 7 8 9 10 11 12
A
TTL
EWDR984 * Configurable by means of a parameter
13 14 15 16 17 18 19 20 21 22 23
69
EWDR 985(/CS LX)
electronic controller for ventilated refrigerating
units

temperature probes (parameter selectable PTC) and four
digital relay outputs to manage the compressors, defrost
cycle, the luminous indicators and the fans or the auxiliary Mounting: DIN rail mounting (Omega 3) or wall-mounting.
ON/OFF function. Connections: screw terminals for _2.5mm2 leads (one lead
This controller also has a configurable 12Vc-20mA output to per terminal for power connections).
manage additional loads like alarms.
Defrost cycles can be stopped at a specific time or as soon as Operating temperature: -5...55C.
the end cycle temperature is reached (if the evaporator is Storage temperature: -30...85C.
equipped with a specific probe). The three analogue inputs
can be used for temperature control, to manage the defrost Operating and storage humidity: 10...90 %RH (non
cycle and to display the related values (or to manage the condensing).
defrost cycle of the second evaporator). Display: 3 digits and a half + sign.
The values measured by the probes are displayed with three Analogue inputs: 3 voltage free digital inputs configurable
digits and a minus sign. The decimal point can be set with a by means of a parameter.
parameter. The buzzer is optional. All models have TTL Serial: TTL for Copy Card
connections that enable the controllers to be used with Copy
Card, the quick programming accessory. RS485 for TelevisSystem.
Digital outputs: 3 digital outputs on relay: 8A 1/2hp 250V
EWDR 985 /CS LX SPST;
The /CS LX models also have:
an internal clock (RTC) to manage the defrost cycle and the 8A 1/2hp 250V SPDT; 16A 1hp 250V SPST; 8A 1/2hp 250V
night and day function; SPST.
an internal opto-insulated RS485 internal connection and
can be connected to TelevisSystem. Configurable 12Vc/20mA output.
digital inputs. Accuracy: above 0.5% of bottom scale +1 digit.
The power supply is 230Va. Consumption: 5VA.
71
RS 485
+ - + - GND
1 2 3 4 5 6 7 8 9 10 11 12
EWDR985/CS LX TTL
13 14 15 16 17 18 19 20 21 22 23 24
1-2 Probe input 1 13-14 Power supply 230Va

1-3 Probe input 2 15-16* N.O. Compressor relay output
1-4 Probe input 3 17-19* N.C. Defrosting relay input
5-6 Digital input 1 18-19* N.C. Defrosting relay output
5-7 Digital input 2 20-22* N.O. Light relay output
8-9* Auxiliary output / 23-24* N.O. Fan relay output
10-12 RS485 network
72
IWC 720
Compact temperature controllers

IWC 720 controllers can be fitted on ventilated refrigerators Front panel protection: IP65.
operating at medium or low temperature. These controllers Casing: plastic, PC+ABS resin, UL94 V-0, polycarbonate
have two analogue inputs for NTC temperature probes (or window, keys in thermoplastic resin.
alternatively PTC inputs) and two programmable relay
Dimensions: front panel 180x37 mm and depth 69 mm.
outputs for the management of the compressor and defrost
cycle. The outputs for the management of the fans of the (without terminals); 45 mm depth for short models.
evaporator, the alarm, lights, auxiliary output and ON/OFF Mounting: panel-mounting, 150x31 mm drilling.
features are selectable. Template (+0.2/0,1 mm
is equipped with a specific probe). The values measured by Storage temperature: 3085C.
the probes are displayed with three digits and a minus sign. Operating and storage humidity: 1090 % RH (non
The decimal point can be set with a parameter. All models condensing).
have TTL connections that enable the controllers to be used
with Copy Card, the quick programming accessory.
Removable terminals are supplied as standard, while the Analogue inputs: 2 NTC/PTC (factory pre-set).
buzzer for the temperature alarm is optional. The range also Digital inputs: 1 voltage free digital input from mains.
includes a special version with a 2hp relay for the direct (clean contact) configurable by means of a parameter.
management of medium power compressors. Screw
Serial TTL output for Copy Card.
terminals or Faston connectors are available on request.
Digital outputs: 2 relay programmable outputs.
Relay output Capacity Accuracy: above 0.5% of the bottom scale +1 digit.
Compressor 16A
Defrosting 20A(2hp)
NOTE: the amperometric values of the devices vary Consumption: 6 VA.
according to the type of terminal used. Power supply: 230 Va/c 10% 50/60 Hz.

7-8 N.O. Defrosting relay output, configurable
7 -9 N.C. Defrosting relay output, configurable
A
10 -11 N.O. Compressor relay output, configurable
IWC 720 230V
12 -13 Power supply
7 8 9 10 11 12 13 14 15 16 17 18 19 14 - 15 Probe input 1
16 - 17 Probe input 2
18 -19 Digital input
73
IWC 730

operating at medium or low temperature. These controllers Casing: plastic, PC+ABS resin, UL94 V-0, polycarbonate
have two analogue inputs for NTC temperature probes (or window, keys in thermoplastic resin.
alternatively PTC inputs) and three programmable relay
outputs for the management of the compressor, defrost
cycle and evaporator. The outputs for the management of (without terminals); 45 mm depth for short models.
the fans of the evaporator, the alarm, lights, auxiliary Mounting: panel-mounting, 150x31 mm drilling.
outputs and ON/OFF features are selectable. Template (+0.2/0,1 mm).
the probes are displayed with three digits and a minus sign. Operating and storage humidity: 1090 % RH (non
The decimal point can be set with a parameter. All models condensing).
with Copy Card, the quick programming accessory.
Removable terminals are supplied as standard, while the Analogue inputs: 2 NTC/PTC (factory pre-set).
buzzer for the temperature alarm is optional. The range also Digital inputs: 1 voltage free digital input (clean contact)
includes a special version with a 2hp relay for the direct configurable by means of a parameter.
Serial TTL output for Copy Card.
terminals or Faston connectors are available on request.
Relay output Capacity Accuracy: above 0.5% of the bottom scale +1 digit.
Compressor 16A
Defrosting 20A(2hp)
Fans 8A. Consumption: 6 VA.
NOTE: the amperometric values of the devices vary Power supply: 230 Va/c 10% 50/60 Hz.
according to the type of terminal used.

5-6 N.O. fan relay output, configurable
A
IWC 730 230V
10 -11 N.O. compressor relay output, configurable
12 -13 Power supply
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 A TTL input for Copy Card

74
IWC 740

operating at medium or low temperature. These controllers Casing: plastic, PC+ABS resin, UL94 V-0,
have two analogue inputs for NTC temperature probes (or
polycarbonate window, keys in thermoplastic resin.
alternatively PTC inputs) and four programmable relay
outputs for the management of the compressor, defrost Dimensions: front panel 180x37 mm and depth 69 mm
cycle and evaporator's fans. The outputs for the (without terminals).
management of the alarms, auxiliary outputs and ON/OFF Mounting: panel-mounting, 150x31 mm drilling.
features are selectable.
Template (+0.2/0.1 mm).
as the end cycle temperature is reached (if the evaporator Operating temperature: 555C.
the probes are displayed with three digits and a minus sign. Operating and storage humidity:
The decimal point can be set with a parameter. All models
1090 % RH (non condensing).
with Copy Card, the quick programming accessory. Display: 3 digits and a half + sign.
Removable terminals are supplied as standard, while the Analogue inputs: 2 NTC inputs (factory pre-set).
buzzer for the temperature alarm is optional. The range also Digital inputs: 1voltage free digital input (clean
includes a special version with a 2hp relay for the direct
contact) configurable by means of a parameter.
terminals or Faston connectors are available on request. Serial TTL output for Copy Card.
Relay output Capacity
Accuracy: above 0.5% of the bottom scale +1 digit.
Compressor 16A
Defrosting 20A(2hp) Resolution: 1 or 0.1C.
Fans 8A. Consumption: 6 VA.
Alarm 8A. Power supply: 230 Va/c 10% 50/60 Hz.
NOTE: the amperometric values of the devices vary

3-4 N.O. alarm relay output, configurable
5 -6 N.O. fan relay output, configurable
A
IWC 740 230V
10 -11 N.O. compressor relay output, configurable
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 12 -13 Power supply

75
IWC 750

operating at medium or low temperature. These controllers Casing: plastic, PC+ABS resin, UL94 V-0,
have two analogue inputs for NTC temperature probes (or
polycarbonate window, keys in thermoplastic resin.
alternatively PTC inputs) and four programmable relay
outputs for the management of the compressor, defrost Dimensions: front panel 180x37 mm and depth 69 mm
cycle, lights, evaporator's fans and ON/OFF feature. The (without terminals).
outputs for the management of the alarms and auxiliary Mounting: panel-mounting, 150x31 mm drilling.
outputs are selectable.
Template (+0.2/0.1 mm).
as the end cycle temperature is reached (if the evaporator Operating temperature: 555C.
the probes are displayed with three digits and a minus sign. Operating and storage humidity:
The decimal point can be set with a parameter. All models
1090 % RH (non condensing).
with Copy Card, the quick programming accessory. Display: 3 digits and a half + sign.
Removable terminals are supplied as standard, while the Analogue inputs: 2 NTC inputs.
buzzer for the temperature alarm is optional. The range also Digital inputs: 1 voltage free digital input (clean
includes a special version with a 2hp relay for the direct
contact) configurable by means of a parameter.
terminals or Faston connectors are available on request. Serial TTL output for Copy Card.
Relay output Capacity
Precision: above 0.5% of the bottom scale +1 digit.
Compressor 16A
Defrosting 20A(2hp) Resolution: 1 or 0.1C.
Fans 8A Consumption: 6 VA.
Alarm 8A. Power supply: 230 Va/c 10% 50/60 Hz.
AUX/light 8A.
NOTE: the amperometric values of the devices vary

1-2 N.O. AUX-light relay output, configurable
3 -4 N.O. alarm relay output, configurable
A
5 -6 N.O. fan relay output, configurable
IWC 750 230V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 10 -11 N.O. compressor relay output, configurable

12 -13 Power supply
76
IWP 740
multifunctional electronic controller
for ventilated refrigerating units
Description
Controller for monoblocs and IWP 740

cabinets with channels Electronic controller for 4 relay refrigerating units with powers
up to 1 hp, 3 NTC temperature probes (factory pre-set PTC
A full range of special electronic controllers for the probes are also available on request), 1 digital input
management of all applications related to monoblocs and configurable by means of a parameter.
refrigerated cabinets with channels, formed by a power unit and All models have TTL connections that enable the controllers to
remote keyboard. be used with Copy Card, the quick programming accessory, and
Controllers are able to manage up to 6 fully configurable relays Televis.
with powers up to 2 hp, up to 4 analogue inputs for The power base is available only for models with open
temperature probes and up to 4 digital inputs that can also be configuration and sizes of 92x121 mm These controllers can be
fully configured by users. connected to the Link network for the synchronization of the
A special algorithm enables all the controllers to connect to the defrost cycles and compressors.
Link network to synchronize the sequence of defrost cycles and The supply voltage is 230 Vc.
start the compressors of all the refrigerating units connected to The module with RS485 serial output for the direct connection
the master unit. These features significantly reduce the of the controller to Televis is optional.
consumption of energy of the whole system.
The possibility of connecting the unit to Televis and the Basic technical specifications
compliance with HACCP requirements guarantees the quality
Dimensions: open, 92x121
and correct preservation of fresh and frozen food, while
Connections for signal inputs: on terminal block for <2.5 mm2
enhancing the performance of refrigerating plants.
leads
Models can be supplied in a sealed plastic casing (167x158x53
Connections for power and supply outputs: on terminal block
mm) or in open configuration in standard DIN size
with 6.3 mm Faston connectors
(107.5x178.5).
Keyboards are available in open configuration without plastic
Storage temperature: 3085 C
casing, which can be mounted on the rear of the panel-
Working and storage humidity: 1090% RH (non condensing).
mounting.
Analogue inputs: 3 inputs for NTC temperature probes (factory
Models are available with powers of 230 Va and 115 Va.
pre-set PTC temperature probes available on request)
Digital inputs: 1 free from voltage inputs
Digital outputs: see table
Serial connection: TTL output (RS485 optional module)
Technical specifications of keyboard
Dimensions: 68.5x124.5, mounting on panel-mounting rear
Resolution: 1 C or 0.1 C
Precision: above 0.5% of the bottom scale.
Power supply: directly from power base.
IWP 740 LX HACCP
store the alarms, in compliance with the HACCP requirements.
Relay output Capacity (amp) Configuration Power (hp)

Defrost 16 SPST 1
Auxiliary 16 SPST 1
Compressor 8 SPST 1/2
Fans 8 SPDT 1/2
77
Wiring Diagram
RS-485 RS-485
Link
Serial Serial Link D.I. Pb1 Pb2 Pb2
Keyboard
IWP 740
A B C D TTL
neutral
gnd
line

Common:
Serial RS-485 Serial output for the connection to A N.O. Defrosting relay output
TelevisSystem (GND, 485-, 485+) B N.O. AUX/light relay output
Link Link C N.O. compressor relay output
D.I. connection Digital input D N.O. fans relay output
Pb1 Probe input 1 D N.C. fans relay output
Pb2 Probe input 2
Pb3 Probe input 3 TTL Serial TTL output for the connection to the Copy Card.
Keyboard Connection to
DATA keyboard, GND, 12V
78
IWP 750 LX, 760 LX
S
Description
IWP 750 IWP 760

Electronic controller for 5-relay refrigerating units with powers
Electronic controller for 6-relay refrigerating units with powers
up to 2 hp, 3 NTC/PTC temperature probes configurable by
up to 2 hp, 3 NTC/PTC temperature probes configurable by
means of a parameter and 4 digital inputs configurable by
means of a parameter and 4 digital inputs configurable by
means of a parameter. All versions have a TTL connector for the
means of a parameter. All versions have a TTL connector for the
connection of the quick programming card Copy Card and
connection of the quick programming card Copy Card and
Televis supervision system. The power base is available for
Televis supervision system. The power base is available for
models with open configuration (107.5x160). Models differ
models with open configuration (107.5x160). Models differ
depending on the distance between the base and keyboard: for
depending on the distance between the base and keyboard: for
distances above 10 meters (model LONG DISTANCE), wiring is
distances above 10 meters (model LONG DISTANCE), wiring is
carried out with an opto-insulated RS485 serial line. If the
carried out with an opto-insulated RS485 serial line. If the
distance is below 10 meters (model SHORT DISTANCE), wiring is
distance is below 10 meters (model SHORT DISTANCE), wiring is
carried out by means of a powered serial line. The supply
carried out by means of a powered serial line. The supply
voltage is 230 Va.
voltage is 230 Va.
The module with serial RS485 output for the direct connection
The module with serial RS485 output for the direct connection
to Televis system and the Link module, required to synchronize
to TelevisSystem and the Link module, required to synchronize
the defrosting cycles and compressors, are optional.
the defrosting cycles and compressors, are optional.
Basic technical specifications
Basic technical specifications
Dimensions: open configuration, (107.5x160), DIN standard
Dimensions: open configuration (107.5x178.5), DIN standard
leads
leads
Operating humidity: 1090% RH (non condensing)
Operating humidity: 1090% RH (non condensing)
Storage humidity: 1090% RH (non condensing)
Storage humidity: 1090% RH (non condensing)
Analogue inputs: 3 inputs for PTC/NTC temperature probes
Analogue inputs: 3 inputs for PTC/NTC temperature probes
configurable by means of a parameter
configurable by means of a parameter
Power supply: 230 Va 10%, 50/60 Hz
Power supply: 230 Va10%, 50/60 Hz
Dimensions: 68.5x124.5, for mounting on panel-mounting rear
Dimensions: 68.5x124.5, for mounting on panel-mounting rear
Display: 3 digits and a half + sign
Display: 3 digits and a half + sign
Resolution: 1C or 0.1C
Resolution: 1C or 0.1C
Precision: above 0.5% of bottom scale
Precision: above 0.5% of bottom scale
Power supply: directly from power base.
Power supply: directly from power base
IWP 740 LX HACCP
IWP 750 LX HACCP
Relay output Capacity (amp) Configuration Power (hp) Relay output Capacity (amp) Configuration Power (hp)
Compressor 20 SPST 2 Compressor 20 SPST 2
Defrosting 16 SPDT 1 Defrosting 16 SPDT 1
Evaporator fan 20 SPST 2 Evaporator fan 20 SPST 2
Alarm 8 SPST 1/2 Alarm 8 SPST 1/2
Light 16 SPDT 1 Light 16 SPDT 1
Standby 8 SPST 1/2
79
Wiring Diagram
Short Long
Distance Distance
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 G
IWP 750-760 H
A B C D E F
neutral
gnd
line

Common: E Relay output E
11 - 12 Digital input 1 G Serial TTL input for Copy Card
13 - 14 Digital input 2 IWP 760
15 -16 Digital input 3 F Relay output F
17 -18 Digital input 4 IWP 750-760 LX
19 -20 Probe input 1 1 - 2 - 3 RS485 serial input for the connection to TelevisSystem
21 -22 Probe input 2 H TTL serial input for the connection to TelevisSystem
23 -24 Probe input 3
A Relay output A
B Relay output B
C Relay output C
D Relay output D
80
IWP 985 /CS LX

The IWP985LX power board has three analogue inputs for Casing: plastic, 4 DIN modules.
NTC temperature probes (parameter selectable PTC) and
four digital relay outputs for control of the compressor,
defrosting, fans, alarm, or light output, auxiliary output, ON- Mounting: DIN rail (Omega 3) or wall-mounting.
OFF. The value read by the probe is displayed on the IWK Connections: on screw terminal block for _2.5 mm2 leads
standard (32x74) remote keyboard with three digits plus the
(one lead for terminal for power connections).
minus sign.
Reading with a decimal point is parameter-programmable. Operating temperature: -5...55C.
The buzzer is optional. All versions have a TTL connection so Storage temperature: -30...85C.
that the Copy Card quick programming accessory can be
used. Operating and storage humidity: 10...90 %RH (non
The IWP985LX power board is fitted with an RS-485 condensing).
optoinsulated internal connection and can also be Analogue inputs: 3 NTC/PTC inputs configurable by means
connected to the TelevisSystem.
of a parameter.
It has two voltage-free programmable digital inputs.
Serial connection: TTL for Copy Card connection
RS485 for TelevisSystem (LX models)
Digital outputs: 4 relay digital outputs. 8A(3) 1/2hp 250V
SPST; 8A(3) 1/2hp 250V SPDT; 16A 1hp 250V SPST; 8A(3)
1/2hp 250V SPST.
Precision: above 0.5% of bottom scale +1 digit.
Consumption: 6VA.
Power supply: 230V.
81
Wiring Diagram
Keyboard
Tastiera
RS 485
+ - GND
1 2 3 4 5 6 7 10 11 12
B
IWP985/CS LX TTL
13 14 15 16 17 18 19 20 21 22 23 24

1-3 Probe 2 15-16*N.O. Compressor
1-4 relays Probe 3 17-19* N.C. Defrosting relay
5-6 Digital input 1 18-19* N.O. Defrosting relay
5-7 Digital input 2 20-22*N.O. Light relay
B Connection Keyboard 23-24*N.O. Fan relay
10-12 RS485 network A TTL input for Copy Card
82
EWPC 1000 (/C, /S)
multifunctional electronic controller for
ventilated refrigerating units

EWPC 1000 Casing: plastic, ABS UL94 V0.
EWPC 1000 controllers can be fitted on ventilated Size: front 215.5x72 mm, depth 110 mm.
refrigerators operating at medium or low temperature.
Mounting: panel-mounting, 209.5x65.5 mm hole.
These controllers have two analogue inputs for NTC
temperature probes, three digital outputs to control the Connections: 6.3 mm Faston terminals.
pressure switching, pre-heating and door switches and six Operating temperature: 560C.
relay outputs to manage the compressors, the defrost cycle, Storage temperature: 3075C.
evaporator's fans, lights and ON/OFF feature, and a low
voltage output for the alarm relay.
Defrost cycles can be stopped at a specific time or as soon Data storage: permanent memory (EEPROM).
as the end cycle temperature is reached (if the evaporator Analogue inputs: 2 PTC probes for temperature and defrost end
is equipped with a specific probe). The values measured by control.
the probes are displayed with three digits. Digital inputs: 3 digital inputs for microport (all), pressure
These controllers are available in standard 215.5x72 size for switch, and preheating.
panel-mounting and with 230, 115, 24 Va or 12 Va/c power
Outputs on relay: 1 output on SPST 15(7)A 250Va relay for
supplies.
compressor, 1 output on SPDT 8(3)A 250Va for defrosting
system, 4 outputs on SPST 8(3)A 250Va relay for evaporator
EWPC 1000/C , EWPC 1000/S
fans, cell light, ON/OFF load buttons, and auxiliary functions.
The EWPC 1000/C and the EWPC 1000/S models have an
internal clock to manage the defrost cycle (Real Time Clock) Alarm repetition output: one (1) 12 Vc/50 mA output for buzzer
and a buffer battery which allows timing even when power or remote alarm repetition relay.
supply is off. Serial connection: RS485 port for connection to the
The EWPC 1000/S model also has a RS485 port for the TelevisSystem (for EWPC 1000/S only).
connection of TelevisSystem. Resolution: 1C.
Power supply (depending on model): 230, 115, 24 or 12 Va
10%, 50 or 60 Hz; 12 Vc 15% (EWPC 1000 only).
83
Wiring Diagram
EWPC 1000
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
+
gnd

Common 2728 Auxiliary relay output N.O.
12 Power supply 2930 Load shutdown relay output N.O.
34 Temperature PTC probe input
56 Defrosting PTC probe input EWPC 1000/S
78 Digital input for microport 161718 RS485 serial connection
89 12 Vc/50 mA alarm output to the TelevisSystem
1215 Digital input for pressure switch

1315 Digital input for preheating
1920 Compressor relay output N.O.
2122 Fan relay output N.O.
2526 Lights relay output N.O.
84
EWTB 1000 (/C, /S)
wall-mounting electronic controller for
refrigerating units

EWTB 1000 controllers can be fitted on ventilated Casing: plastic, ABS UL94 V0.
refrigerating units operating at normal or low temperatures. Size: front panel 211x178 mm, depth 80 mm.
These controllers have two inputs for PTC thermostatic
Mounting: wall-mounting.
probes, three digital inputs for preheating, pressure switch,
door switch and seven relay outputs to manage the Connections: 6.3 mm Faston terminals.
compressor, the defrost cycle, the evaporators fans, the Operating temperature: 560C.
lights, the ON/OFF function, the alarm and an Storage temperature: 3075C.
auxiliary output.
as the end cycle temperature is reached (if the evaporator Data storage: permanent memory (EEPROM).
is equipped with a specific probe). The values measured by Analogue inputs: 2 PTC probes for temperature and defrost
the probes are displayed with three digits. end control.
These controllers are available in standard size for wall- Digital inputs: 3 digital inputs for door switch, pressure
mounting and with 230, 115, 24 Va or 12 Va/c power switch and preheating.
supplies.
Outputs on relay: 1 output on SPST 15(7)A 250Va relay for
compressor, 1 output on SPDT 8(3)A 250Va for defrost
EWTB 1000/C, EWTB 1000/S
system, 5 outputs on SPST 8(3)A 250Va relay for evaporator
The EWBT EWTB 1000/C and EWTB 1000/S models have an
fans, cell light, ON/OFF load button, alarm and auxiliary
internal clock to manage the defrost cycle (Real Time Clock)
functions.
and a buffer battery which allows timing even when power
supply is off. Serial connection: RS485 port for TelevisSystem (for EWTB
The EWTB 1000/S model also has a RS485 port for the 1000/S only).
connection of TelevisSystem. Resolution: 1C.
Power supply (depending on model): 230, 115, 24 or
12 Va 10%, 50 or 60 Hz; 12 Vc 15% (EWTB 1000 only).
85
Wiring Diagram
EWTB 1000
1 2 3 4 5 6 7 8 12 13 14 15 19 20 21 22 23 24 25 26 27 28 29 30 31 32

12 Power supply 2122 Fan relay output N.O.
34 Temperature PTC probe input 2327 Defrosting relay output N.O.
56 Defrosting PTC probe input 2427 Defrosting relay output N.C.
78 Digital input for microport 2526 Lights relay output N.O.
1215 Digital input for pressure switch 2728 Auxiliary relay output N.O.
1315 Digital input for preheating 2930 Load shutdown relay output N.O.
1920 Compressor relay output N.O. 3132 Alarm relay output N.O.
86
EWCM 400
Controllers for multiple compressors
and condensers

EWCM 400 controllers can be used to manage compressor Front panel protection: IP65
plants with standard Eliwell Casing: plastic, fire extinguishing, UL94V0
32x74 sizes.
Dimensions: front panel 70x32 mm, depth 70 mm
These controllers have 4 relay outputs for the management
of compressors, an analogue input for inlet (NTC Mounting: panel-mounting, 71x29 mm hole
temperature or pressure probe configurable by means of a Connection: COLV power cable
parameter), a condenser analogue input (420 mA for COHV signal cable
pressure probe) and 7 digital inputs for the management of
CORK inverter output cable (EWCM 418 only)
temperature control alarms of compressors, high and low
pressure and generic shutdowns. Operating temperature: 560C
All models have TTL connections that enable the controllers Storage temperature: 2085C
to be used with Copy Card, the quick programming Inlet analogue input: NTC temperature probe or 420 mA
accessory. All models use the ModBUSRTU standard for pressure probe configurable by means of a parameter
communication protocol.
Analogue condensation input: 420 mA for pressure probe
The values measured by probes is displayed with 3 digits.
These controllers have a 12 V power supply. Digital inputs: 7 free-voltage digital inputs reserved to low
and high pressure alarms, remote ON/OFF and four generic
EWCM 412 alarms for compressor.
EWCM 412 has a triac 12...24V output for the management Digital outputs for compressors: 4 2(2)A 250Va relays
of condensing fans with powers up to 2 A, for power in Alarm output: 1 TRIAC output, 12...24 Vc/500 mA max
higher range, a PWM connection to an external fan module (EWCM 412) or 1 2(2)A 250Va relay (for models
is excepted.
EWCM 415 and EWCM 418)
EWCM 415 Analogue output: 1 PWM output for the management of a
EWCM 415 has a relay output for the management of condenser control card (EWCM 412)
alarms. This controller does not control condensation. Inverter output: 420 mA analogue output or 010 V
configurable by means of a parameter for the direct
EWCM 418
management of an inverter module (only for model EWCM 418).
EWCM 418 has a relay output for the management of
alarms and an analogue output (4..20 mA or 010 V) to Serial output: TTL port for quick programming with Copy
enable the control of condensation by means of an inverter. Card or for the connection to remote supervision system.
Communication protocol: protocol Televis or ModBUSRTU
Resolution of inlet probe: 0.1C/1F for NTC temperature
probe, 0.1 bar or 0.01 bar for the inlet pressure probe
(configurable by means of a parameter)
Resolution of condensation probe: 0.1 bar (fixed)
Precision: 0.8C with the 035C range for temperature
sensor, 1% of bottom scale for pressure sensor
Power supply: 12 Va/c10%, 50/60 Hz
87
Wiring Diagram
12a ALL gnd gnd ST2 ST1 ID7 ID6 12a n.c. gnd gnd ST2 ST1 ID7 ID6
S K S K
12a 12c TK1 ID5 ID4 ID3 ID2 ID1 12a 12c n.c. ID5 ID4 ID3 ID2 ID1
EWCM 412 EWCM 415

9 8 7 6 5 4 3 2 1 9 8 7 6 5 4 3 2 1
1 2 3 4 1 2 3 4
12a n.c. gnd gnd ST2 ST1 ID7 ID6

S K
12a 12c n.c. ID5 ID4 ID3 ID2 ID1
EWCM 418
9 8 7 6 5 4 3 2 1
1 2 3 4

12a Power supply 3-7-8-9 Common relay outputs
12c Output for the supply of pressure transducers 1 N.O. compressor relay output, configurable
gnd ground connection with terminals 4
N.C. Not used for 2 N.O. compressor relay output, configurable
TK1 PWM output for the management of with terminals 3
a condenser control card 4 N.O. alarm relay output (models 415/418)
(only for EWCM 412 models) 4 (T) TRIAC output (only for model EWCM 412)
ST1 Suction probe 5 N.O. compressor relay output, configurable
ST2 Condenser probe with terminals 2
ID1 Temperature control input 1 6 N.O. compressor relay output, configurable

with terminals 1
ID2 Temperature control input 2
S Serial port input
K Connection for remote keyboard
E Output 010 V/420 mA
ID5 Unit block input
(only for EWCM 418 models)
ID6 High pressure alarm input
ID7 Low pressure alarm input
88
EWCM 800 series
controller for compressor pack units

EWCM 800 controllers can be used to manage all Casing: plastic, ABS UL94 V0.
compressors in a compressor room of refrigerating plant Size: front panel 72x144 mm, depth 120 mm.
by means of the inlet pressure. These controllers offer
Mounting: panel-mounting with fixing brackets, 67x136 mm
reversal tables for the most used freon gases and enable
hole.
therefore values to be displayed and set in bar, PSI,
C and F. Connections: screws with a disjoining clamp.
Depending models, they can have 4 (EWCM 840/S), 6 Display: 4 digits.
(EWCM 860/S) or 9 (EWCM 890/S) compressors; each Compatible freon gases: 22, R 134 A, 502, 404 A, 407 A, 507A.
compressor must have an alarm input to disconnect the
Low pressure input sensor: 420 mA programmable or NTC
system in the event of failure.
(depending on model).
It is possible to configure two different set points: for
standard operation or for operation with limited Minimum pressure switch: 1 opto-insulated voltage input
requirements. (same voltage as power supply).
The reduced set point can be configured by means of the Alarm output: 6(3)A 250Va SPST relay.
internal clock or by a clock enabled with a digital input.
Alarm controller output: 6(3)A 250Va SPST relay.
EWCM 800 models have a RS485 serial connection for
TelevisSystem. The values measured by the probes are Number of configurable outputs: 4, 6 or 9 on 6(3)A 250Va
displayed with 4 digits. SPST relay, depending on model.
These controllers are available with 230, 115, 24 or 12 Va Alarms: 4, 6 or 9 inputs in opto-insulated voltage (usually
power supplies.
with the same voltage as power supply).
Serial output: RS485 port for connection of TelevisSystem.
Resolution: 0,01 bar; 0,1 PSI (C); 1 F.
Consumption: 6 VA.
Power supply: 230, 115, 24, 12 Va 10%; 50/60 Hz.

12 Alarm relay output 44 45 Relay 1 output
34 Safety relay output 46 47 Relay 2 output
56 Low pressure alarm input 48 49 Relay 3 output
9 10 Power supply 50 51 Relay 4 output
11 12 GND 52 53 Relay 5 output
13 14 Reduced set input 54 55 Relay 6 output
15 16 Evaporator probe input 56 57 Relay 7 output
19 20 21 RS485 serial connection to 58 59 Relay 8 output
the TelevisSystem 60 61 Relay 9 output
22 23 Alarm input
24 25 Alarm input
26 27 Alarm input
89
Wiring Diagram
EWCM 890
+ gnd +
1 2 3 4 5 6 9 10 11 12 13 14 15 16 19 20 21
EWCM 890
22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
C1 t2 t3 C2 t2 t3 C3 t2 t3
K1 K2 K3 K4 K5 K6 K7 K8 K9
K1 K2 K3 K4 K5 K6 K7 K8 K9
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61
EWCM 890
90
EWCM 900/S

EWCM 900/S are controllers for managing compressors and Casing: plastic ABS UL94V0.
fans in the machinery compartment of a refrigerating Size: front panel 72x144 mm, depth 120 mm.
system. The compressor control is performed by detecting
the suction pressure of the system while the fan control is
hole.
performed by monitoring the condensation pressure.
They contain the reversal tables for the most used freon Connections: removable screws terminals.
gases, allowing to display and set data directly in bars, C Compatible freon gases: 22, R 134 A, 502, 404 A, 407 A,
and F. They have 11 outputs on relay for compressor and 507A.
fan management; each compressor is provided with an Inlet sensor input: 420 mA programmable or NTC
alarm input in order to cut off from operation in case of
(depending on model).
fault.
Two different setpoints can be set: one for standard Outlet sensor input: 420 mA programmable or NTC
operation and the other for reduced operation. (depending on model).
The reduced setpoint is set through either an internal clock Minimum pressure switch: 1 opto-insulated voltage input
or by a clock enabled with a digital input. EWCM 900/S are
(same voltage as power supply).
provided with a RS485 serial connection to link to the
TelevisSystem; data are viewed on two displays: a 4digit Outlet pressure switch: 1 opto-insulated voltage input
display and a 3digit display. The power supply voltage can (usually with the same voltage as power supply).
be optionally 230, 115, 24, or 12 Va. Alarm output: 6(3)A 250Va SPST relay.
Failure controller output: 6(3)A 250Va SPST relay.
Number of configurable outputs: 11 on 6(3)A 250Va SPST relay.
Alarms: 11 opto-insulated voltage inputs (usually
with the same voltage as power supply).
Serial output: RS485 port for connection of TelevisSystem.
Consumption: 6 VA.
Power supply: 230, 115, 24, 12 Vc 10%; 50/60 Hz.

12 Alarm relay output 44 45 Relay 1 output
34 Safety relay output 46 47 Relay 2 output
56 Low pressure alarm input 48 49 Relay 3 output
78 High pressure alarm input 50 51 Relay 4 output
9 10 Power supply 52 53 Relay 5 output
11 12 GND 54 55 Relay 6 output
13 14 Reduced set input 56 57 Relay 7 output
15 16 Evaporator probe input 58 59 Relay 8 output
17 18 Condenser probe input 60 61 Relay 9 output
19 20 21 RS232 serial connection to
the TelevisSystem
22 23 Alarm input
24 25 Alarm input
26 27 Alarm input
28 29 Alarm input
30 31 Alarm input
91
Wiring Diagram
EWCM 900
+ + gnd +
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
EWCM 900
22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
C1 t2 t3 C2 t2 t3 V1 V2 V3
K1 K2 K3 K4 K5 K6 K7 K8 K9
K1 K2 K3 K4 K5 K6 K7 K8 K9
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
EWCM 900
92
EWCM 809/NH3/S

EWCM 809/NH3/S controllers can be used to manage all Casing: plastic ABS UL94V0.
compressors in a compressor room. The compressors are Size: front panel 72x144 mm, depth 120 mm.
controlled by means of the inlet pressure. These controllers
offer reversal tables for R-717 gas (ammonia) and enable
hole.
therefore values to be displayed and set in bar, C and F.
These controllers have 9 relay outputs that can be used to Connections: removable screws terminals.
manage compressors and fans. Each compressor has an Type of cooler: ammonia.
alarm input to disconnect the system in the event of failure. Low pressure input sensor: 4...20mA programmable or NTC
In the event of failure, the control switches to an (depending on the model)
emergency system to allow it to run at its minimum load
Minimum pressure switch: 1 optic insulated voltage input
until it is serviced.
(same voltage as power supply)
It is possible to configure two different set points: for
standard operation or for operation with limited Alarm output: on 6(3)A 250Va SPST relay.
requirements. Falling controller output: on 6(3)A 250Va SPST relay.
The reduced set point can be configured by means of the Number of configurable outputs: 9 outputs on 6(3)A 250Va
internal clock or by a clock enabled with a digital input. SPST relay according to the model.
EWCM 809/NH/S models have a RS485 serial connection for
Alarms: 9 optic insulated voltage inputs (usually with the
TelevisSystem. The values measured by the probes are
same voltage as power supply).
displayed with 4 digits.
These controllers are available with 230, 115, 24 or 12 Va Serial output: RS485 port for connection to the
power supplies. TelevisSystem.
Consumption: 6VA.
Power supply: 230, 115, 24, 12Va 10%, 50/60 Hz.
Wiring Diagram
EWCM 809 NH3

+ gnd +
1 2 3 4 5 6 9 10 13 14 15 16 19 20 21
12 Alarm relay output
34 Safety relay output
56 Low pressure alarm input
9 10 Power supply
EWCM 809 NH3
13 14 Reduced set input
22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
15 16 Evaporator probe input
19 20 21 RS232 serial connection to
the TelevisSystem
22 23 Alarm input
C1 t2 t3 C2 t2 t3 C3 t2 t3
24 25 Alarm input
K1 K2 K3 K4 K5 K6 K7 K8 K9 26 27 Alarm input
4461 Relay output 1Relay output 9
K1 K2 K3 K4 K5 K6 K7 K8 K9
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61
EWCM 809 NH3
93
WM 961 (/A, /B)
single stage controller for temperature

WM 961 controllers have one point of intervention only, are Front panel protection: IP30.
for wall-mounting and can be used for refrigeration Casing: plastic, PC+ABS, self-extinguishing, UL94V0.
applications. These controllers have 1 input for NTC
temperature probes and 1 output relay to manage the
loads. Mounting: wall-mounting.
Defrost cycles are controlled through timers that stop the Connections: screw terminals for max 2.5 mm2
compressor at specific intervals of time. leads (one lead per terminal for power connections).
The values measured by the probe are displayed with two
digits and sign. The WM 961/A model also has a alarm relay
output, while the WM 961/B model has a buzzer for Storage temperature: 3075C.
acoustic alarms. These controllers are available in standard Display: 2 digits plus sign, 12.5 mm high.
80x123S size for wall-mounting and with 230 Va or 12 Va/c Data storage: permanent memory (EEPROM).
power supplies.
Input: NTC probe with reinforced insulation.
Main output: 1 output on 15A 1 hp 250 Vc SPDT relay.
Auxiliary output: 1 output on 12 Vc/20 mA max (/A model).
Measurement range: 5050C.
Resolution: 1C.
Power supply: 230 Vc or 12 Va/c10%, 50/60 Hz.

12 Relay N.O.
+
23 Relay N.C.
45 Power supply
67 Output 12 Vc (optional)
9 8 7 6 5 4 3 2 1 89 Probe input
WM 961
94
blast and quick chillers, ovens and
monoblock split units
Description
Solutions for temperature Technical Data

Signal inputs connections: 6.3 mm Faston connectors.
blast chilling cells Power output connections: removable screw terminals for <2.5
mm2 leads.
Cards for temperature blast chilling cells are electronic Viewing: digits 12.5mm high.
controllers which manage all blast chilling, freezing and Operating temperature: 565C.
preservation functions. Storage temperature: 3075C.
These devices are suitable for all refrigeration and catering Operating humidity: 10..90% RH (non condensing).
applications, but can be used also on combined devices, Storage humidity: 10..90% RH (non condensing).
because they blast chill the product at temperatures close to Relay outputs: see table.
0C or values suitable for deepfreezing, depending on Analogue inputs: 2 inputs for PTC temperature probe (to
requirements. These cards are therefore the ideal solution to control temperature and the end of the defrost cycle) , 1 PTC
guarantee a safe and optimal preservation of all types of food. wire probe to control the center of the product.
Digital inputs: 4 inputs for door switch, compressor alarm and
fan alarm.
EWFC 1000 Measurement range: 50100C.
EWFC 1000 controllers are designed for temperature blast Resolution: 1C.
chilling and preserving cells. Power supply: 230 Va 10%, 50/60 Hz.
These controllers have three analogue inputs for PTC
temperature probes, to control the defrost end and to measure
the product temperature. They also have 3 digital inputs for the
contacts of pressure switch alarms, and fan and door switch Relay output Amp. capacity Configurat. Hp power
alarms. Compressor 15(6) SPST 1
The switching from the positive, hard positive or negative blast Defrost 10(4) SPST 1/2
chilling cycle to preservation cycle can occur when the Evaporator fans 10(4) SPST 1/2
temperature measured by the insertion probe (wire probe) has Lights 10(4) SPST 1/2
been reached or at a specified time, if this probe is not
available.
The cell thermostat is always on the cell probe. The control is
configured to start at specific intervals of time, even if a "wire"
probe is present and it has not been placed at the center of the
product.
Defrost cycles can be configured by the user depending on
requirements.
An internal buzzer signals when the cycles have been correctly
completed. The buzzer can also signal a pressure switch or cell
probe alarm.
The outputs on relays control all blast chiller actuators:
compressor, fans, defrosting cycle and lights.
95
Description
Solutions for industrial ovens

A complete range of electronic controllers specifically designed
to manage all electrical and gas industrial ovens applications for
gastronomy and pastry.
The ability to individually manage temperatures inside the cell,
signal alarms and set different times of operation are some of
the features that account for the extraordinary versatility and
flexibility of these controllers.
MT6
MT6 cards are specifically designed for electrical or gas
convection ovens with heating distribution on top/bed plate.
The control can be configured depending on the kind of oven it
is installed in, by means of configuration parameters accessible
through a specific procedure and by means of a password.
The control consists of a base card with inputs, outputs, control
logic and an interface with keys, LEDs and displays.
The control is available in 4 versions for RM modular ovens, CE
electrical convection ovens, CG gas convection ovens and for RC
cell ovens, which differs from the version for RM ovens only in
terms of software configuration.
Temperature probes are of TCI probes and can be configured to
detect room, steam generator and exchanger temperatures.
The measurement range is 20C - 500C. Measured values are
displayed with 3 digits and sign.
These controllers have three digital inputs and 8 relay outputs
to manage (depending on the model) the electrical heaters, the
burner, the steam generation and inlet, the extraction of fumes,
lights and fans.
An additional analogue output enables to directly control the
phase trimming fan.
All controllers have a 230 Va power supply 10%, 50/60Hz.
96
FASEC 33
automatic fan control with 1 input and
1 output for condensation

FASEC 33 automatic fan controls can be fitted on Casing: plastic, selfextinguishing, NORYL.
refrigerating units with condensing function. These Size: 48x96 mm front panel, depth 96 mm (without base).
controllers have an input for PTC temperature probes and a
Triac output to manage loads up to 2.5 A. A version for
loads up to 7 A with an external LC filter and a version for Connections: Octal base (included for 7A models).
Ziehl motors can also be supplied on request. Operating temperature: 560C.
The set point can be set to all values within the 060C Storage temperature: 3075C.
range. These controllers come in standard 48x96 size with
Input: 1 for PTC probe.
230 Va power supplies.
Output: 1 on Triac.
External filter (for 7 A version): load power supply 7 A max
current; 38 mm cylinder size, 28 mm height; M8 fixing bolt.
Type of control: depending on phase power step.
Type of function: for condensation.
Output power: 2.5 A or 7 A.
Power supply: 230 Va 10%, 50 Hz.

12 Power supply
18 Output on triac
45 Input for PTC probe
6 5 4 3
FASEC
33/43
7 8 1 2
97
FASEC 43, 43C
fan automatic control with 1 input and
1 output for evaporation function

FASEC 43 Casing: plastic, selfextinguishing, NORYL.
FASEC 43 automatic fan controllers can be fitted on Size: front panel 48x96 mm, depth 96 mm (without base).
refrigerating units with evaporator function.
These controllers have 1 input for PTC temperature probes
and a Triac output to manage maximum loads of 2.5 A. A Connections: Octal base (included for 7A models).
version for loads up to 7 A with an external LC filter and a Operating temperature: 560C.
version for Ziehl motors can also be supplied on request. Storage temperature: 3075C.
The set point can be set to all values within the -4030C
Input: PTC probe.
range. These controllers come in standard 48x96 size with
230 Va power supplies. Output: 1 Triac.
FASEC 43C current; 38 mm cylinder size, 28 mm height; M8 fixing bolt.
FASEC 43C differ from FASEC 43 because their operating Type of control: depending on phase power step.
range is 060C
Type of function: for evaporation.
Output power: 2.5 A or 7 A.

12 Power supply
18 Output on triac
6 5 4 3
FASEC
33/43
7 8 1 2
98
FASEC 53
fan manual control

FASEC 53 automatic fan controllers can be fitted on Casing: plastic, selfextinguishing, NORYL.
refrigerating units. Size: front panel 48x96 mm, depth 96 mm (without base).
These controllers have a Triac output to manage maximum
loads of 2.5 A. A version for loads up to 7 A with an
external LC filter and a version for Ziehl motors can also be Connections: Octal base (included for 7A models).
supplied on request. Operating temperature: 560C.
These controllers come in standard 48x96 size with 230 Va Storage temperature: 3075C.
power supplies.
Adjustment: from 0 to 100% using a knob on the front
panel.
Control output: 2.5 A Triac, 7 A Triac.
current; 38 mm cylinder size, 28 mm height; M8 fixing bolt.
Type of control: manual, depending on phase power step.
Power supply: 230 Va 10%, 50 Hz .

12 Power supply
18 Output on triac
6 5 4 3
FASEC 53
7 8 1 2
99
FASEC 100
automatic fan control with 1 input for
condensation and evaporation function,
rear panel or wall-mounting

FASEC 100 automatic fan controllers can be fitted on Casing: plastic, GW, self-extinguishing, V0 (model with IP 55 casing)
refrigerating units with condensing function. Size: 100x70 mm open version, depth 40 mm; 183x110 mm
These controllers have 1 input for PTC temperature probes IP55 version, 100 mm depth.
and a Triac output to manage maximum loads of 2.5 A.
Mounting: wall-mounting (IP55 models), rear of panel
The set point can be set to all values within the 3055C
mounting (open models).
range. These controllers come in standard size for rear
panel mounting and 230 Vc power supplies. Operating temperature: 555C.
Wall-mounting models support maximum loads of 2,5 A. Storage temperature: 3075C.
Adjustment: set point (3055C), differential (325C) and
minimum speed (080 %, optional for FASEC 100); start at
maximum speed for 10 seconds (removable).
Input: PTC probe.
Output: 1 Triac output.
Type of control: depending on phase power step, using Triac
with LC filter.
Type of function: automatic control for condensation
(increase of temperature = increase of speed) or
evaporation (decrease of temperature = increase of
speed); manual control (on request), speed proportionate
to the position of the trimmer on the front panel.
Output power: 2,5 A for both models (open board and IP55)
Wiring Diagram

12 Power supply
18 Output on triac
FASEC 100 45 Input for PTC probe
2
1
8
4
5
100
FASEC 500
fan automatic control with 1 input for
condensation and evaporation function,
backofboard or wall-mounting

FASEC 500 automatic fan controllers can be fitted on Casing: plastic, GW, self-extinguishing, V0 (model with IP55 casing)
refrigerating units with condensing and evaporating Size: 150x135 mm open model, depth 65 mm; 222x143 mm
function.
IP55 model, depth 103 mm .
These controllers have 1 input for PTC temperature probes
and a Triac output to manage maximum loads of 23 A. Mounting: wall-mounting (IP55 models) or rear panel
The set point can be set to all values within the 3055C mounting (open3 models).
range. These controllers come in standard size for rear Operating temperature: 555C.
panel mounting and 230 Va power supplies. Storage temperature: 3075C.
IP55 models support maximum loads of 2,5 A.
Adjustment: set point (3055C), differential (325C) and
minimum speed (080 % optional, only for FASEC 500); start
at maximum speed for 10 seconds (removable).
Input: 1 for PTC probe.
Output: 1 Triac output.
Type of control: depending on phase power step, using Triac
with LC filter.
Type of function: automatic control for condensation
(increase of temperature = increase of speed) or
evaporation (decrease of temperature = increase of
speed); manual control (on request), speed proportionate
to the position of the trimmer on the front panel.
Output power: 23 A for both models (open board and IP55).

12 Power supply
18 Output on triac
FASEC 500
4
5
8 1 2
101
WM 203
Automatic fan control with 2 inputs
and 1 output for conditioning,
wall-mounting

WM 203 automatic fan controllers can be fitted on Front panel protection: IP50.
refrigerating units with conditioning function. Casing: plastic, ABS, selfextinguishing with self locking.
These controllers have 1 input for PTC temperature probes,
room temperature and outlet water temperature and 1Triac
output to manage maximum loads of 2.5 A. Mounting: wall-mounting with fixing screws (supplied).
The controller is able to automatically select the Connections: screw terminals for max 2.5 mm2 leads.
summer/winter mode. These controllers come in standard Operating temperature: 555C.
75 x 108 size and 230 Va power supplies.
Adjustment range: from 10 to 30C using a knob on the
front panel.
Analogue inputs: two PTC probes.
Control output: 2.5 A Triac with LC filter.
Type of function: fan speed automatic control; automatic
reversal between summer and winter mode.
Consumption: 2 VA.

12 Input for delivery water PTC probe
34 Input for room temperature PTC probe
56 Power supply
78 External ON/OFF control
910 Output on Triac
WM 203
1 2 3 4 5 6 7 8 9 10
102
WM 253
speed manual control, wall-mounting

WM 253 automatic fan controllers can be fitted on Front panel protection: IP50.
refrigerating units with conditioning function. Casing: plastic, ABS, selfextinguishing with self locking.
These controllers have 1Triac output to manage maximum
loads of 2.5 A.
These controllers come in standard 75 x 108 size and 230 Mounting: wall-mounting with fixing screws (supplied).
Va power supplies. Connections: screw terminals for max 2.5 mm2 leads.
Adjustment range: from 0 to 100% using a knob on the
front panel.
Control output: 2.5 A Triac with LC filter.
Type of function: manual control; speed proportionate to
the position of the potentiometer on the front panel.
Consumption: 2 VA.

12 Power supply
34 External ON/OFF control
56 Output on Triac
WM 253
1 2 3 4 5 6
103
6 Data Acquisition and Printing
Data recording and printing 6.1 PRINTWELL 1200 105

devices offer a practical 6.2 PRINTWELL 1200 Slave Module 106
solution to monitor 6.3 EWLP 120 107
processes and the operation
of one or more systems.
The range includes both
models designed to record
and print values measured
by sensors connected to the
device and models with
integrated sensor that do
not require electrical
connections.
104
Printwell 1200
Two channel data recorder
(expansible to six)

Printwell 1200 is a fully configurable data recorder able to Front panel protection: IP30
print values read by transducers (on two different Casing: plastic in ABS
channels of the master module + 4 channels on the
Dimensions: 96x96 mm, depth 90 mm
optional slave module) connected to the input of the
device on thermal paper. Mounting: panel-mounting
The recorder has several keys and an LCD display so that it Connections: removable screw terminal block
can be customized according to requirements. Operating temperature: 055 C
The internal clock enables to print the measured values at
Number of channels: 2 direct channels and 4 optional
regular intervals (that can be set at a minimum of 60
seconds). channels on slave module
All channels can be programmed and used to manage PTC Inputs: 2 direct inputs and 4 optional inputs on save
or NTC probes, J or K modules for PTC or NTC probes, J or K thermocouples,
thermocouples, Pt100 2-wire probes and 420 mA current Pt100 2-wire probes and 420 mA current transducers
transducers with a single device. Digital input: input for remote printing
Printouts provide the following information:
Measuring range: 45150 C for PTC, 20110 C for NTC,
- Unit of measurement and progressive number of the print
100...700 C for J thermocouples,100...1300 C for K
- The reason of the printout (the printing operation can be
thermocouples, 100600 C for 2-wires Pt100 probes (the
set to automatic, performed at regular intervals when the
range varies according to the sensor used)
timer is operating or started manually by pressing a key on
the remote control Resolution: 1 C, 1 F, 1% R.H., 1 bar
- Printout time (in hours, minutes and seconds) Type of paper: thermal paper not sensitive to light; width of
- Day, month and year of measurement print: 48 mm
- Measurement channel
Maximum dimension of paper roll: 58x30 mm
The printer can also save the measured values at a preset
time (configurable by means of a parameter) and print all Power supply: 110-240 Va 10%, 50/60 Hz (standard) or
the data acquired between two printouts at a specific time 1236 Va/c, 50/60 Hz (on request)
of the day or when the remote print output is enabled.
Maximum absorbed power: 12 W

123 Connection to Slave module
11 12 4 Auxiliary output 12 Vc
56 Digital input
7- 8 Input 2
910 Input 1
PRINTWELL 1200
1112 Power supply
1 2 3 4 5 6 7 8 9 10
gnd +
7 8 9 10 4 5 6 7 8 9 10 4 5 6 7 8 9 10
+ +
TcJ/TcK R PTC/NTC/Pt100 420mA 420mA
105
Printwell 1200
4-channel slave module for Printwell
1200

4-channel slave module for Printwell 1200. Front panel protection: IP40
The four channels can be programmed and used to manage Casing: plastic in ABS
PTC or NTC probes,
Dimensions: front part 71x90, 58 mm depth
J or K thermocouples, Pt100 2-wire probes and 420
mA current transducers with a single device. Mounting: on DIN rail
Connections: removable screw terminal block
Operating temperature: 055 C
Number of channels: 4 channels
Input: 4 inputs for PTC or NTC probes, J or K
thermocouples, Pt100 2-wire probes and 420 mA current
transducers
Measuring range: 45150C for PTC, 20100C for NTC,
50640 C for K thermocouples, 50400C for 2-wire
Pt100
Resolution: 1C or 1F, 1% R.H.,1 bar
Auxiliary output: 12 Vc for the supply of transducers
Power supply: 90-240 Va 10%, 50/60 Hz (standard) or 12
Va/c, 50/60 Hz (on request)
Maximum absorbed power: 12 W.
The maxim um absorbed power is 12 W.

1-2-3 Connection to Slave module
13 14 15 4-5 Input 3
6-7 Input 4
9-10 Input 5
11-12 Input 6
PRINTWELL 1200
8 Auxiliary output 12 Vc
SLAVE MODULE
13-15 Power supply
1 2 3 4 5 6 7 8 9 10 11 12
gnd +
4 5 6 7 8 9 10 11 12 4 5 6 7 8 9 10 11 12 4 5 6 7 8 9 10 11 12
+ + + +
TcJ/TcK TcJ/TcK PTC/NTC/Pt100 PTC/NTC/Pt100 420mA 420mA 420mA 420mA
106
EWLP 120
Data recorder 2 + 1 channels
Description
EWLP 120 are temperature, humidity or pressure recorders two 1600 values and have configurable measuring ranges. Data can
inputs for thermostatic PTC or Pt100 be printed along with comments in any of the selected
(or current for humidity and pressure) probes, a digital input for languages.
the door switch and one alarm relay output. All these recorders have a buffer battery with an autonomy of
These recorders can monitor two different points, store up to six hours.
Technical Data
Front panel protection: IP40 (with open cover) of 0.5% RH
or IP65 (with closed cover) Clock module: accuracy of 0.1% and buffer battery
Casing: ABS plastic Configurable parameters:
Size: 161x192 mm, depth 94 mm Year - month - day - hour minutes
Mounting: holes for wall-mounting Instrument code number (max 4 digits)
Connections: screw terminals Temperature reading time: 1 - 240 minutes
Operating temperature: 050C Negative and positive alarm for each analogue channel
Data storage: permanent memory with capacity Delay for positive, negative and open port; set alarm
of 1.600 readings acquisition
Digital input: input for detecting open port. from 1 to 60 minutes
Alarm output: on 8(2)A 250Va relay (switching contact). Selectable language (I-GB-FR-D-S)
Measurement range: Type of printer: 24 columns, 7x5 matrix on
4070 C with resolution of 0.5 C and accuracy of 0.5 C thermal and non-photosensitive paper (with a width of 57 mm)
for PTC Power supply: 230 Va 10%, 50/60 Hz
-80350 C with resolution of 0.5 C and accuracy of 0.5 C
for Pt100 2 configurable channels as:
030 Bar (420 mA) with resolution of 0.5 Bar and accuracy 2 PTC 1 PTC + 1 Pressure
of 0.5 Bar
2 Pt100 1 Pt100 + 1 RH
099% RH (420 mA) with resolution of 0.5% RH and accuracy
1 PTC + RH 1 Pt100 + 1 Pressure

12 Power supply
35 Alarm relay output N.O.
45 Alarm relay output N.C.
67 Input for buffer battery
PTC PTC 420 mA
+ 89 Digital input
1011 Input for current 420 mA
17 16 15 14 13 12 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Pt100 Pt100
121314 Input for probe
151617 Input for probe
EWLP 120
17 16 15 14 13 12
107
7 Systems
TelevisSystems are an ideal Monitoring and Remote Assistance Solutions

solution to automatically 7.1 Televis 150 111
record temperature in 7.2 Televis 200 113
7.3 TelevisStation 3500/3700 115
compliance with
7.4 TelevisCompact 20/40/60 117
international regulations. 7.5 TelevisInteractive Family 119
These systems also offer the
advantages of a network Televis Network
when several devices are 7.6 Example and notes for the installation 121
connected to a personal
computer or electronic unit. 7.8 PCInterface2150 124
This user friendly, easy to use
solution, supervises the Data Control and Acquisition Modules
7.9 EWTV 200 125
whole system and alerts the
7.10 EWTV 240 126
support function when 7.11 EWTV 270 127
problems occour. 7.12 EWTV 280 128
It is the ideal solution to 7.13 EWTV 150 129
preserve the quality of food.
Accessories
TelevisSystems is able to 7.14 BusAdapter 130 130
record all the data of the 7.15 BusAdapter 150/350 131
refrigerating system, along 7.16 SmartAdapter 132
with alarms and information
on the remote operation of
the instrumentation.
110
TelevisSystem150 up
down
CELLA
FRIGORIFERA
set
monitoring software
up up
down
set down
set
up up
down
set down
set
S
up
down
set
up up
down set down set
Description
TelevisSystem150 is an efficient solution to monitor
temperatures and any other physical units of measurements of
refrigerating systems used for the preservation and processing
of food.
TelevisSystem150 program is able to communicate with a series
of modules, designed to measure analogue values (temperature,
humidity, etc.), logical statues (alarms, door switches, pressure
switches) and with a series of instruments which can be
connected to one other using an ordinary serial line linked to a
Personal Computer.
TelevisSystem150 can be installed in new or existing systems,
regardless the type of controllers used for the
regulation.
The user friendly and easy to use interface makes this system
suitable also for beginners.
ALARM MANAGEMENT
The devices linked on line continuously transmit
the measured data to the computer, thus
enabling users to promptly manage alarms and
abnormal operating conditions.
After detecting the fault, users can enable
warning or emergency devices using the EWTV
280 module.
A practical procedure enables to automatically
transmit faxes/SMS messages every time an alarm
occurs.
Messages are automatically sent to the preset
numbers of Help Centers or authorized operators.
ENABLING REMOTE ACTIONS

REMOTO
Televis 150 can be connected, via modem and an ordinary telephone line, to a
computer installed in a remote location as compared to the refrigerating
system. The efficient software routines of the program enable users to carry
out the actions remotely, thus facilitating the outsourcing of the management
and troubleshooting of the refrigerating system.
LOCALE
111
RECORDING
AND PRINTING
All the data transmitted from the modules to the
PC are recorded at specific intervals, in
accordance with the requirements or
recommendations regarding food preservation.
The data storage capacity of the PC is defined at
the time the system is configured.
All the values stored on the hard disk can be
printed or displayed at any time. It is also
possible to select a start or end date for the
desired intervals of time. Users can print reports,
graphs and tables or customize the system
according to the type of data analysis they wish
to carry out.
DATA DISPLAY
IN REAL TIME
The main information transmitted by devices
(inputs values and statuses) can be viewed in real
time. The PC displays an immediate detailed
overview of the system's status along with a
series of functions that the user can select for
data analyses purposes. It is also possible to
display the information stored in the system.
A pane shows the list of all the devices that have
detected an alarm condition. To display the
details of an alarm or device, it is sufficient to
select it. The second pane that opens displays
real time and historical data.
112
TelevisSystem200
monitoring and remote management software
Description
TelevisSystem200 has been designed to monitor and manage
problems associated to refrigerating systems. Operations can be
carried out locally using a PC or from a Help Center via modem.
The system enables users to simply and practically monitor and
display all alarms.
LAYOUT
The layout shows the physical arrangement of the instruments
within the plant in which they are installed. Therefore, it enables
to acquire immediate information on all the instruments from
one location only.
The main information is graphically displayed for each
instrument shown. The program can manage up to 100 different
layout sheets.
RVD
The concept of virtual instrument has been specifically
developed to help users to work on-site. The controller that
needs to be managed is displayed, thus allowing users to select
all the configuration and options on the screen as it were a real
instrument.
Most of new instruments can be connected using an opto-
insulated RS485 line with high immunity from
disturbances.
The system can also automatically detect all the instruments
connected to the PC. If the plant configuration is changed, it is
sufficient to run this routine to reconfigure the system.
113
GLOBAL COMMANDS
This function enables to simultaneously perform specific
operations on all the devices with a single command.
It is possible, for example, to switch the devices and lights on
and off, or perform this operation for each single device. The
diagnostic tool enables users the view the results of the
commands they have selected for each device..
ALARM MANAGEMENT
Televis 200 continuously queries the connected instruments,
acquiring all possible data including information on the alarms
reported. RECORDING AND PRINTING
User-friendly panes display information on the alarms in real
TelevisSystem200 continuously monitors the status of the
time, thus enabling the user to be continuously updated on the
system. Users can therefore require information on the
status of the system.
temperature of a specific unit or cell or even historical data. It is
If an alarm or abnormal situation occurs, TelevisSystem200
also possible to display information on previous failures and use
performs the action specified by the user during set-up. For
this information to program scheduled maintenance before the
example, it can automatically send a detailed fax/SMS message
occurrence of a serious problem. Printouts are compliant with
to the preset numbers.
the food standards. Data is printed with a resolution of one
tenth to ensure full compliance of all printed documentation
with applicable standards and regulations.
REMOTO
REMOTE MANAGEMENT
The most important advantage offered by Televis 200 lies in the possibility of
completely controlling a system from a PC installed in a remote location as
compared to the site of installation of the instruments.
LOCALE The use of a modem, the possibility of notifying alarms telephonically and the
RVD function enable the operators of Help Centers to perform the same
operations that are available on the local PC in the site of installation.
Remote management functions enable users to send fax messages to preset numbers even if a computer
is not available.
114
TelevisStation
central unit with pre-installed
Televis software
Description
TelevisStation is ideally suited for Televis 150 and Televis 200
software because it is a personal computer that meets the more
TelevisStation3500
restrictive reliability and quality industry standards. TelevisStation3500 is compact and can be easily mounted on
The license for the application software must be purchased walls and on panels (2 screws are required for wall-mounting, 1
separately. The software is pre-installed and can therefore be for the safety lock).
immediately used after a few simple operations. The available
models are TelevisStation3500 and TelevisStation3700 . It is also possible to purchase an accessory (available on
This program is available in several versions, depending on the request) to protect the connectors and power switch from
type and the language of the operating system installed and tampering.
pre-installed software versions and models.
The LCD monitor display high resolution images, thus simplifying
the use of the software.
TelevisStation3500 also has a VGA for the connection of
external monitors.
The internal modem, approved in the main European countries,

is pre-installed. To use the software (also remotely, via modem)
immediately, it is sufficient to the telephone line.
It is also possible to use an external modem without removing
the internal one.
The product contains the EWTK module (depending on the

selected license) that usually interfaces the PC and the RS485
network. Therefore, only three network cable terminals (+,
and gnd) are used for the connection of TelevisStation3500
and for immediate programming.
TelevisStation3500 also has a PS2 connector for the keyboard

and another one for the mouse (accessories supplied). A parallel
port for the printer and other auxiliary ports (RS232, USB,
Ethernet) are also available for additional requirements and
future expansions.
A 3 1/2 floppy drive (supplied) is also available.
Although the software is compatible with several operating

systems, it is preferable to use it with Microsoft Windows, as this
OS enables to efficiently use the features of TelevisStation3500
and Station 150/200.
The operating system (in Italian or in English) is supplied as

standard. The availability of other languages must be checked
when the order is placed.
TelevisStation3700
Like the model TelevisStation3500 plus Touch-Screen.
115
Note: the figure is provided for information purposes
Technical Data only. The manufacturer reserves the right to make
technical and aesthetic changes without modifying the
Casing: metallic varnished, IP20. price and the name of the product. Check the
hardware and software configurations available when
Size: 320x260x140 (L x H x P).
placing the order.
Mounting: wall-mounting.
Power supply: 110240 Va, 50/60 Hz.
Accessories: protection for connections.
116
TelevisCompact
electronic unit for remote management
and installation monitoring
Description
TelevisCompact is an electronic unit that enables to remotely
manage plants and monitor installations by connecting several TelevisCompact20
Televis compatible instruments to a network.
It is suitable for local monitoring
applications. This program reads and saves
Together with the two complementary software applications,
data from devices connected on line (from
TelevisInteractive and TelevisInteractivePlus, is the ideal
a maximum of 35 devices at recording
solution for customers who wish to control a single installation
intervals of 15 minutes), detect alarm
(monitoring and plant management) and for customers who
conditions and record them. If an alarm occurs, the device
need to simplify the monitoring of several plants or require an
notifies its occurrence by switching the LED on the display on,
automatic and centralized solution for remote installations.
enabling the buzzer and alarm relay, and by sending faxes and
The installation and configuration of TelevisCompact is quick
SMS to several users.
and easy. All operations can be performed from the keyboard of
All recorded data can be displayed on the LCD display and
the devices, but also by means of the user-friendly program for
printed.
PCs (Configuration tool) that runs in a Windows environment.
If TelevisInteractive is used, it is also possible to transfer all the
The products of the TelevisCompact family can record data at
data saved to a TelevisCompact20 memory bank.
user-defined time intervals.
The data storage time interval varies according to the number of

devices connected and to the time interval chosen for the
recording.
Collected data can be printed manually or automatically or

transmitted, via modem, to a Help Center where the
TelevisCompact60
working software TelevisInteractive stores all the data. If an This application is particularly suitable to
alarm occurs, the electronic exchange displays the information access data via modem. TelevisInteractive
using a LED on the front panel. If a modem or fax is available, it displays and changes the operating
is possible to send notifications via SMS to a Help Center or to parameters of TelevisCompact60 as well as
TelevisInteractivePlus. the instrument parameters of the tools
linked on line. TelevisCompact60 can be
The software stores the data and, if necessary, sends messages configured to send alarms to TelevisInteractivePlus software,
and alarm notifications for each alarm received from local which records them and enables users to display and print them.
installations. Depending on the settings selected during the product
configuration, it is also possible to filter the alarms and send
The system can also transmit (via fax) a daily status report, at them via fax or SMS even to multiple users. Thus, the software
the user-defined time, and display a history of the last alarms receives all data automatically and centrally and manages several
occurred, both for system alarms (TelevisCompact) and network installations. The information acquired on instrumentation can
alarms (instruments connected to the system). be periodically sent to TelevisInteractive or
A password system prevents non authorized users from using TelevisInteractivePlus to allow it to be centrally recorded; this
the instrument. function can be activated automatically to avoid that older data
be erased when the memory is freed up to make space for new
Three models of TelevisCompact are available: data.
TelevisCompact20, TelevisCompact40 and TelevisCompact60. All other functions are identical to those of the previous model.
Not all the functions listed above are available for the three
models. The sections that follow detail the characteristic of each
model to allow users to select the version that best suits their
needs.
117
TelevisCompact40 Technical Data
If remote management of the Casing: metallic varnished, IP20.
installation only (or rather that there is Size: 197x198x60 (L x H x P).
no need locally to intervene directly) is
Mounting: on wall.
of interest, this is the ideal product. It
offers all the functions of Relay: free-voltage contacts, 12/24 Va/c, Imin 100mA - Imax 1A
TelevisCompact60 except that it has Power supply: 230 Va 10%, 50/60 Hz.
neither a display, nor a buzzer nor alarm relay. Furthermore Absorption: max 5 VA.
the memory available is limited; this happens, obviously,
Connections: Televis RS485 port; 2 modem/PC RS232 ports;
since all the data are periodically sent to the
Centronics printer port.
TelevisInteractive central software or to
TelevisInteractivePlus software which records them
periodically and makes them available for future use.
CONFIGURATION TOOL
This software automatically recognises all the devices connected to one
TelevisCompact and enables the selection of desired operation by means of setting
up the machine parameters.
It is, thus, possible to quickly, simply and safely set up the tools
names, the time interval for data acquisition, help centers, etc.
Furthermore, it is possible to execute a series of advanced
operations which must be carried out exclusively by specialized
personnel; operations which allow to update the second language
available for software and communication drivers with the tools;
should the TelevisCompact model include it, the operations
described may also be done via modem.
118
TelevisInteractive Family
software for the remote and centralized
management of one or more installations
Description
TelevisInteractive
This software can be used to
interact with TelevisCompact and
the devices connected to it.
It is also possible to directly
connect the PC to TelevisCompact
using the serial port or remotely via
modem. This connection enables
users to download data or monitor
all the devices connected on line. Connection via modem
is available for TelevisCompact40 and TelevisCompact60
only.
Collected data can be processed and exported, displayed
and printed as table or chart. It is also possible to use
the RVD (Remote Virtual Device) function and global
commands on any device connected to the network.
If appropriately configured, TelevisInteractive can also
operate in call waiting mode. In this mode, data
downloading is carried out automatically without the
operator's supervision.
This function is also available onTelevisCompact40 and
TelevisCompact60.
TelevisInteractivePlus
The TelevisInterctivePlus software
extends of TelevisInteractive.
If set in "call mode" the software is
able to receive alarm messages from
one or more TelevisCompact40 or
TelevisCompact60. The messages are
stored for each single installation and
are available for subsequent viewing.
The incoming messages can be forwarded to the final
recipients (including several users) at specific intervals of
time (hour/day/month/year) that can be configured for
each user.
Information on the activities undertaken and transmission
result are saved and may be displayed at a later time
along with all the other information associated with the
alarm.
119
Televis network
Example of connection of a TelevisSystem
Description
Devices are connected to the network by means of a
RS485 opto-insulated connection to ensure a higher
protection from electromagnetic disturbances and electric
noise.
Some devices manufactured by Eliwell already have a TTL Connection
RS485 serial connection, while others have a TTL serial

output. The latter require a specific interface module to
converts the TTL output into RS485 for the connection to
the network. This module is part of the BusAdapter range.
The devices that can be connected include Televis TTL RS485

Converter
controllers described in several sections of this catalogue
and data acquisition modules described in the last part of
Device
this section. with TTL port
INSTALLATION NOTES RS485

Network
1 NOTE 1
Use a shielded and twisted cable with two leads having a section of 0.5 mm2 and a
sheath (reference to Belden cable model 8762 with PVC sheath, 2 leads and sheath, 20
AWG, rating between the leads of 89pF, rating between a lead and the shielding 161pF).
In special cases (for example when there is a high level of noise) it may be necessary to
use cables with higher performances.
Cables should be installed in accordance with the requirements of data transmission
standard EN 50174. RS485 Network
It is particularly important to separate the data transmission data from the power lines
The length of the RS-485 network that can be connected to the device is 1200 m and
the maximum number of devices that can be connected is 32.
It is possible to expand the length of the network and the number of devices connected
to each channel by means of special repeater modules.
See manual Installation of the RS-485 network for further information. Terminal
blocks of devices are of two types:
Device
- Single with 2 leads: use only + and - leads and connect the gnd lead (sheath) to with RS485 port
the direct current
- Single or double with 3 leads: use all 3 leads (+, - for the signal and gnd for the
sheath).
2 NOTE 2: apply 120 , 0,25 W electric heaters between terminals + and - of the
interface and of the last device of each branch of the network.
3 Note 3
The network cable is connected by means of TelevisCompact or TelevisStation
terminals while the PC is connected by means of the PCInterface module supplied as
standard with software Televis 150 and Televis 200.
Module PCInterface is connected to the PC by means of serial line RS232.
4 Note 4
It is necessary to assign to each network device a unique address by setting
parameters FAA and dEA.
121
Televis network application example
TelevisCompact Personal Computer TelevisSystem
122
PCInterface1100
RS232-RS485 converter with single and
split outputs

PC Interface series 1100 is a RS-232/RS-485 interface Casing: plastic, 9 DIN module, 155x117mm
module that enables a PC with RS-232 interface port to Depth: 51 mm
communicate with several devices compatible with protocol
Mounting: DIN rail mounting (Omega 3) or wall-mounted
Micronet/Televis connected to a RS-485 network. This
device can be used only of it BlueCard enabling module, Protection class: IP20
supplied with Eliwell package licenses, is available. Ambient temperature/humidity: 055 C / 1090% non
PC Interface series 1100 is enclosed in a plastic casing that condensing
houses 9 DIN 155x117 mm modules, with a depth of 51 mm Storage temperature/humidity: 2085 C / 1090% non
that can be mounted on DIN rail (Omega 3) or wall condensing
mounted. The module is powered directly from the mains.
Power supply: 230Va 10%, 50/60 Hz
PC Interface series 1100 is available in the following Screw terminal block for 2.5 mm2 (one lead per terminal)
versions: Absorption: 6VA max
- PC Interface 1110 has a single RS-485 connector Insulation: class II
- PC Interface 1120 has two RS-485 connectors that enable
Relay: clean contact, N.O. 250Va 3A max.
the network to be split in two branches
Screw terminal block for 2.5 mm2 (one lead per terminal)
To allow Televis software to correctly detect the device, it is RS-232 port: maximum speed 115kbps, DB9 female
necessary to insert the BlueCard enabling module with connector
software licence. RS-485 port: 9600kbps, opto--insulated (500V)
Wiring Diagram - Description of Wiring Diagram
1110
1120
POWER Power LED RS-485 Line (only 1120)

Rx 232 232 Serial GND RS 485 GND GND RS 485 GND
RX LED (red) Tx 485485 Serial Transmission LED (green) + RS 485 + + RS 485 +
Rx 485 485 Serial RX LED (red) - RS 485 - - RS 485 -
Tx 232 232 Serial TX LED (green)
SUPPLY Power cable (internal connection)
PC RS-232Connection between PC and PCInterface
Alarm N.O. Alarm relay
123
PCInterface2150
RS232-RS485/TTL converter
with 12Va auxiliary power supply

PC Interface series 2150 is a RS-232/TTL-RS-485 interface Casing: plastic, 9 DIN modules, 155x117mm.
module that enables a PC with RS-232 interface port to Depth: 51 mm.
communicate with a device compatible with protocol
Mounting: DIN rail mounting (Omega 3) or wall-mounted
Micronet/Televis connected by means of a TTL or RS-485
port. This device can be used only if the BlueCard enabling Protection class: IP20.
module, supplied with Eliwell package licenses, is available. Ambient temperature/humidity: 055 C / 1090% non
PC Interface series 2150 is enclosed in a plastic casing that condensing.
houses 9 DIN 155x117 mm modules, with a depth of 51 mm Storage temperature/humidity: 2085 C / 1090% non
that can be mounted on DIN rails (Omega 3) or wall- condensing.
mounted. This module is powered directly from the mains.
Power supply: 230Va 10%, 50/60 Hz.
To allow Televis software to correctly detect the device, it is Screw terminal block for 2.5 mm2 (one lead per terminal)
necessary to insert the BlueCard enabling module with Absorption: 6VA max.
software license. Insulation: class II.
RS-232 port: maximum speed 115kbps, DB9 female
connector.
RS-485 port: 9600kbps, opto-insulated (500V).
TTL port: 5-way Molex connector.
Wiring Diagram - Description of Wiring Diagram

Aux Out
- +12V Aux
Out Out
2150 TTL
POWER Power LED +12V Out +12V 250mA max output always powered
Aux Out Aux Led Out - Common
Rx 232 232 Serial RX LED (red) GND RS 485 GND
Tx 485 485 Serial Transmission LED (green) + RS 485 +
Rx 485 485 Serial RX LED (red) - RS 485 -
Tx 232 232 Serial TX LED (green) TTL 5-way TTL Molex cable
SUPPLY Power cable (internal connection)
PC RS-232Connection between PC and PCInterface
Aux Out N.O. Auxiliary relay
124
EWTV 200
data acquisition module for
temperature

The EWTV 200 module is used to connect the sensors used Casing: plastic, 4 DIN module, front panel 70x85 mm.
for temperature data acquisition that are part of a Depth: 61 mm.
TelevisSystem installation.
Mounting: DIN rail mounting (Omega 3).
The configuration module enables to set the measurement Connections: telephone type receptacle for connection with
parameters of the single probes, the units of measurement EWTV 150 and two screw terminal blocks 2.5 mm2; (one
of values and the general alarm settings. wire only per each terminal) for the remaining electrical
The EWTV 200 comes in a 4module 70x85 mm casing wiring.
suitable for either Dinrail (Omega 3) or surface mounting Operating temperature: 560C.
and is powered directly by mains line voltage. Storage temperature: 3075 C.
Inputs: three (3) PTC semiconductor probes.
Serial connection: double RS485 serial port for the
connection to TelevisSystem.
Power supply (depending on model): 230, 115, 24 Va 10%,
50/60 Hz.

12 PTC input probe n 3
34 PTC input probe n 2
1 2 3 4 5 6 56 PTC input probe n 1
EWTV 150
131415 RS485 serial output for
TelevisSystem connection
EWTV 200 161718 RS485 serial output for
2224 Power supply
13 14 15 16 17 18 22 24
gnd + gnd +
RS-485 RS-485
125
EWTV 240
data acquisition module for
420 mA inputs

The EWTV 240 module is used for the current inputs Casing: plastic, 4 DIN module, front panel 70x85 mm.
coming output by humidity probes (EWHS 28/31), pressure Depth: 61 mm.
transducers (EWPA 007/030) or other signals 4...20mA.
The module has three 4...20 mA inputs.
If used with TelevisSystem software, it is possible to assign a Connections: telephone type receptacle for connection with
unit of measurement (C, F, %R.H., Bar, Psi, etc.) to all EWTV 150 and two screw terminal blocks 2.5 mm2; (one
inputs and display the minimum and maximum values for wire only per each terminal) for the remaining electrical
each current input. wiring.
The configuration module enables to set the measurement Storage temperature: 3075C.
parameters of the single probes, the units of measurement
Inputs: three (3) 420 mA outputs.
of values and the general alarm settings.
The EWTV 240 comes in a 4module 70x85 mm casing Serial connection: double RS485 serial port for the
suitable for either Dinrail (Omega 3) or surface mounting connection to TelevisSystem.
and is powered directly by the mains line voltage. Power supply (depending on model): 230, 115, 24 Va 10%,
50/60 Hz.

1 GND
2 420 mA output n 3
1 2 3 4 5 6
EWTV 150 3 420 mA output n 2
4 420 mA output n 1
5 12 Vc output
EWTV 240
6 12 Vc output
13 14 15 16 17 18 22 24
gnd + gnd +
RS-485 RS-485
2224 Power supply
126
EWTV 270
digital inputs acquisition module

The EWTV 270 module is an interface between the Casing: plastic, 4 DIN module, front panel 70x85 mm.
TelevisSystem and voltage logical inputs. It can be used to Depth: 61 mm.
control the status of different loads (compressors, room
lights, antimist or defrost electric heaters, etc.)
The module has three voltage inputs with the same rating Connections: telephone type receptacle for connection with
of the power supply (230, 115 and 24 Va); 1 module is also EWTV 150 and two screw terminal blocks 2.5 mm2; (one
available with inputs and power supply for a voltage of 24 wire only per each terminal) for the remaining electrical
Va. wiring.
If used with Televis, it is possible to assign a name to both Operating temperature: 560C.
"statutes" of each module input, in order to permit the Storage temperature: 3075C.
configuration module set the measurement parameters of
Inputs: three (3) opto-insulated voltage 220 or 24 Va,
the single probes, the units of measurement of values and
depending on model.
the general alarm settings.
Serial connection: double RS485 serial port for the
EWTV 270 is available in the standard 70x85 mm size (4 DIN connection to TelevisSystem.
modules) for DIN rails (Omega) or for wall-mounting and is Power supply (depending on model): 230, 115, 24 Va 10%,
directly powered by the mains. 50/60 Hz.

34 logical input n 3
1012 Power supply
3 4 5 6 7 8 10 12
EWTV 270
EWTV 150
13 14 15 16 17 18
gnd + gnd +
RS-485 RS-485
127
EWTV 280
alarm management module

The EWTV 280 module is a remote repeater for the Casing: plastic, 4 DIN module, front panel 70x85 mm.
management of signals of TelevisSystems. Depth: 61 mm.
These signals may be generated by system alarms
(excessively high or low temperature, power failure, faulty
probe, etc.) which occur on instruments or other modules Connections: telephone type receptacle for connection with
in the network. Signals are sent to EWTV 280 through the EWTV 150 and two screw terminal blocks 2.5 mm2 (one
TelevisSystem software which, for this purpose, can relate wire only per each terminal) for the remaining electrical
the relay output to an instrument or a group of wiring.
instruments. Operating temperature: 560C.
EWTV 280 provides a second relay which is triggered in the Storage temperature: 3075C.
event of no link alarm (no communication on serial line
Outputs: two (2) SPST relays 8(3)A 250Va for the remote
from an instrument or module). In the event of
repetition of two alarm signals foreseen by the
communication failure due to cable breakdown or PC fault,
an additional security feature in EWTV 280 activates both TelevisSystem: the measured value exceeding maximum
relays for alarm repetition. and minimum thresholds of one of the system probes and
TelevisSystems can be connected to a maximum of 15 the no link alarm (module not responding to the system).
EWTV 280 modules. Serial connection: double RS485 serial port for the
EWTV 280 is available in 70x85 mm standard size (4 DIN connection to TelevisSystem.
modules) for DIN rails (Omega 3) or for wall mounting and Power supply: 230 Va 10%, 50/60 Hz.
is directly powered by the mains.

56 no link alarm
78 system alarm
LA SA
5 6 7 8 161718 RS485 serial output for
EWTV 150
2224 Power supply
EWTV 280
13 14 15 16 17 18 22 24
gnd + gnd +
RS-485 RS-485
128
EWTV 150
portable keyboard
SS
Description
EWTV 150 is a portable keyboard that can be used to
program the EWTV 200, EWTV 240, EWTV 270, EWTV 280
modules of TelevisSystem.
It assigns identification codes to identify the individual
modules of a plant (FAA and dEA parameters)
and to configure the required parameters.
The modules and the EWTV 150 keyboard are connected
through a cable supplied with a polarized telephone
receptacle.
The module directly powers EWTV 150.
Technical Data
Weight: 400 g.
Data display: with 12.5 mm high digits.
Connection cable length: about 300 mm.
129
Bus Adapter 130
TTL RS485 interface
with 12Va auxiliary output

BusAdapter 130 is a 3 DIN rail module that enables to Front panel protection: IP40.
interface a device with a serial TTL port to a RS485 network. Casing: box with 3 DIN modules.
Mounting: Omega-DIN rail.
The device has a TTL serial input for the connection of the
device, a screw terminal opto-insulated RS485 output for Operating temperature: 555C.
the connection to the communication network and an Storage temperature: 3075C.
auxiliary output for the supply of the device. Operating and storage humidity: 1090 % RH (non
Note: two sets of RS485 connectors are available to simplify condensing).
the connection to the network. This means that it is
Insulation class: 2.
possible to use three terminals for the connection of the
incoming cables and three for outgoing cables. Power supply and consumption: 230/115 Va 1.5/6 Va,
depending on models.
Auxiliary output: 12 Va (5 VA).
Serial connections to the network: dual RS485 port for
Serial connections to the device: TTL port to connect the
device by means of a multi-wire 5-pole cable with a length
of 1 m, supplied as standard; other lengths available on
request.
Wiring Diagram
GND
GND
+
+
-
1 2 3 4 5 6 7 8 9 Description of Wiring Diagram

BusAdpater 130
123 RS485 serial port
89 Power Supply
TTL power supply TTL input for the connection of devices
1718 Auxiliary output
10 11 12 13 14 15 16 17 18
130
Bus Adapter 150, 350
TTL RS485 Interface with high
insulation properties

BusAdapter 150/350 is a 3 DIN Rail module that enables to Front panel protection: IP40.
interface a device with a serial TTL port to a RS485 network. Casing: box with 3 DIN modules.
Mounting: Omega-DIN rail.
Models have a TTL serial input for the connection of the
device, a screw terminal opto-insulated RS485 output for Operating temperature: 560C.
the connection to the communication network. These Storage temperature: 3075C.
modules also have a reinforced 500V insulation. Operating and storage humidity: 1090 % RH (non
Note: two sets of RS485 connectors are available to simplify condensing).
connection to the network. This means that it is
possible to use three terminals for the connection of the
incoming cables and three for outgoing cables. Power supply and consumption: 230/115 Va 1.5/6 VA,
Attention: this model is not equipped with an auxiliary depending on models.
output for the supply of the device (see BusAdpater130). Serial connections to the network: dual RS485 port for
BusAdpater350 Serial connections to the device: TTL port to connect the
This adapter must be used when specified in the technical device by means of a multi-wire 5-pole cable with a length
sheet of the controller to which it is combined. For devices of 1 m, supplied as standard; other lengths available on
required a reinforced insulation for serial line RS485. request.
For FCBasicom it is necessary, for example, to use model
BusAdapter350 only.
Wiring Diagram
GND
GND
+
+
-
1 2 3 4 5 6 7 8 9 Description of Wiring Diagram

BusAdpater 150/350
89 Power Supply
TTL power supply TTL input for the connection of devices
10 11 12 13 14 15 16 17 18
131
SmartAdapter
ModBUS converter for Televis networks

SmartAdapter is a ModBUS protocol converter for Televis Frontal panel protection: IP40.
networks, in 3 DIN rail size, that enables the Housing: plastic 3 Din modules.
TelevisSystem software to use the RS-485 serial line to
Mounting: on Din rail.
connect devices using a ModBUS protocol.
Use temperature: 560 C.
It has an opto-insulated RS485 serial line for the connection Storage temperature: 3075 C.
to the Televis network. Use environment humidity: 1090 % RH*.
Storage environment humidity: 1090% RH*
ModBUS devices are connected through the TTL (without
optical insulation) or the second opto-insulated RS485 serial *(not condensing).
port. Serial connections:
TelevisSystem side
The monitoring system (software or TelevisCompact)
double RS-485 serial port for the connection to the
requires a specific driver to communicate with the ModBUS
instrument via the SmartAdapter converter. TelevisSystem;
Baud rate: 9600 Baud optoisolated.
ModBUS side
double RS-485 serial port for the connection to the
ModBUS instruments;
TTL for connection with 1 instrument;
Baud rate: 9600 or 19200 Baud.
Insulation Class: 2.
Power supply: 230Va 1,5VA .

TelevisSystem side
RS - 485 Televis
POWER SUPPLY 1-2-3 RS 485 serial port

GND
GND
4-5-6 RS 485 serial port

+
+
-
8-9 230Va power supply
1 2 3 4 5 6 7 8 9
ModBUS side
SmartAdapter 10 - 11 - 12 RS 485 serial port
A To TTL input
ModBUS side Televis side
16 ModBUS TX serial LED

17 ModBUS RX serial LED
18 Power supply LED
10 11 12 13 14 15 16 17 18
A TX RX ~
RX ModBUS
POWER
+
GND
TX ModBUS
-
RS - 485
ModBUS
132
8 Accessories
A wide selection of 8.1 Temperature probes 135

accessories to integrate the 8.2 EWHS 280, 300, 310 137
available instrumentation: 8.3 EWPA 007, 030 138
8.4 Miscellaneous 139
temperature, humidity and
8.5 Switches 141
pressure probes; power 8.6 Fan Controllers 142
supplies for probes and a
wide range of transformers.
These and other
instruments offer users all
the necessary tools to
improve quality and output.
134
PROBES
Temperature probes

Temperature probes are manufactured in several materials Type of sensor Range
so that they can be used with a wide range of temperatures. NTC 50110 C
Probes are fitted with PTC and NTC sensors or Ni100 and PTC 55150 C
Pt100 thermocouples. Depending on the type of sensor, the Ni100 ELECTRIC HEATER 50150 C
protection capsule (that is usually cylindrical) can be in ABS, Pt100 ELECTRIC HEATER 100600 C
Aisi 304/316 stainless steel and Inconel. To further protect THERMOCOUPLE J 0600 C
the sensor, special materials (resins) have been used for the THERMOCOUPLE K 01350 C
area between the sensor and capsule. The cable that
transmits the signal to the instrument is in PVC, silicon or Type of cable Range
Vetrotex and available in several lengths. The operating PVC Plastic 3080
range depends on the materials and type of sensor used. Silicon 60200
Vetrotex 0350
Container material Range

ABS 3080
AISI 304 80600
INCONEL 01200
NTC probes Characteristics and models

Type of sensor Type of cable Casing material Range (C)
Resinbonded NTC PVC (light gray) ABS 3080
Resinbonded NTC PVC (light gray) AISI 304 steel 3080
Resinbonded NTC Silicon (blue) AISI 304 steel 50110
PTC probes Characteristics and models

PTC (A) for air PVC (black) Bare sensor 3080
Protected PTC (A/P) for air PVC (black) AISI 304 steel 3080
Protected PTC (A/P) S for air Silicon (dark gray) AISI 304 steel 55150
Wall-mounting PTC (W) / Plastic 40120
Tube-mounted PTC (T) PVC (black) ABS plastic 2080
Resinbonded PTC (S) Silicon (dark gray) AISI 304 steel 55150
Resinbonded PTC (N) PVC (black) AISI 304 steel 3080
135
Ni100 probes Characteristics and models
Protected Ni100 (A/P) for air PVC AISI 316 steel 3080
Protected Ni100 (A/P) S for air Silicon AISI 316 steel 50150
Standard normal Ni100 (N) PVC AISI 316 steel 3080
Standard normal Ni100 (N) S Silicon AISI 316 steel 50150
Wall-mounting Ni100 (W) / Plastic 5080
Pt100 probes Characteristics and models

Protected Pt100 (A/P) S for air Silicon AISI 316 steel 60200
Protected Pt100 (A/P) V for air Vetrotex AISI 316 steel 0350
Standard normal Pt100 (N) S Silicon AISI 316 steel 60200
Standard normal Pt100 (N) V Vetrotex AISI 316 steel 0350
Special Pt100 (N) V3P Vetrotex Protected AISI 316 Steel 0600
Wall-mounting Pt100 (W) / Plastic 40120
Thermocouple J Characteristics and models

J (N) thermocouple FeCo Vetrotex AISI 316 steel 0600 *
*For end part only
Thermocouple K Characteristics and models

K (N) thermocouple CrAl Vetrotex AISI 316 steel 0600 *
K (N) thermocouple CrAl Vetrotex ICONEL 01350 *
*For end part only
136
EWHS 280, 300, 310
Humidity probes
Description Technical Data EWHS 300

EWHS probes are designed to be connected to instruments Insulation class: IP65.
measuring humidity. Size: 80x80x52 mm.
EWHS 280 and EWHS 300 probes are provided with a (318
Mounting: using the external slots.
mA and 420 mA) current output for humidity while EWHS
310 probes are provided with two (020 mA) current Electric connections: screw terminals.
outputs, respectively for humidity and temperature. Operating temperature: 3070 C.
Operating humidity: 0100% RH.
Humidity measurement range: 0100% RH.
Output current of humidity measurement:
4(0%)20(100%) mA;
Technical Data EWHS 280
Response time at 23C: 30 seconds.
Insulation class: IP54. Recovery time from saturation: 90 seconds.
Size (mm): 103x25 mm. Storage temperature: 3080 C.
Mounting: use the clip provided with the probe. Number of connection leads: 2.
Electric connections: PVC bipolar cable. Maximum load: 250 .
Connection cable: 1.5 m or 3.0 m. Humidity measurement accuracy (23 C):
Operating temperature: 1060 C. 2% RH (10..95% RH), 3% RH (<10% >95% RH);
Operating humidity: 0100% RH. Air filter: polyethylene.
Humidity measurement range: 1590% RH. Protection from polarity reversal
Output current of humidity measurement: Temperature compensation: with NTC;

3(15%)18(90%) mA. Max air speed: 20 m/s.
Response time at 23 C: 60 seconds. Power supply: 930 Vc.
Recovery time from saturation: 360 seconds.
Number of connection leads: 2 (blue: electric power supply;
brown: output).
Maximum load: 250 .
Humidity measurement accuracy (23 C): 5% RH
(15..90% RH)
Air filter: metallic wire network.
Protection from polarity reversal
Max air speed: 20 m/s.
Power supply: 928 Vc.
137
EWPA 007, 030
Pressure probes
Technical Data EWHS 310 Description

Insulation class: IP65. EWPA probes measure pressure and are have a
Size: 80x80x52 mm. 420 mA current output to transfer the signal to the
measurement instrument. EWPA 007 can operate with
Mounting: through external slots
max. pressures of 7 bars, while EWPA 030 can handle up
Electric connections: screw terminals to 30 bars.
Operating humidity: 0100% RH.
Temperature measurement range: 3070 C.
Humidity measurement range: 0100% RH.
Output current of: Technical Data EWPA 007, 030
Humidity measurement: 0(0%)20(100%) mA.
Temperature measurement: 0(30 C)20(70 C) mA. Protection class: IP65.
Response time at 23C: 30 seconds Operation range: 0,57 bar for EWPA 007 and 030 bar
for EWPA 030.
Recovery time from saturation: 90 seconds
Overload: EWPA 007: 20 bar, EWPA030: 100 bar.
Number of connection leads: 4.
Global error at room temperature: 1% e.o.s.
Maximum load: 250 .
Global error at 050C: typical 1%, max 2%.
Humidity measurement accuracy (23C):
Global error for values other than 050C: typical 2.5%,
1,5% RH (10..95% RH), 2% RH (<10% >95% RH).
max 4%.
Temperature measurement accuracy at 0C and 23C:
Impact resistance: sinusoidal impulse, 20 g/11 msec (IEC
0.5 C (for different temperatures accuracy is equal to the 68236).
Pt100B temperature plus 0.2 C).
Vibrations: 52000 Hz/10 g on 3 axes (IEC 6826).
Air filter: polyethylene
Compensated temperature: 050 C.
Protection from polarity reversal
Connection: using 2 wires.
Temperature compensation: with Pt100B.
Output: current 420 mA with 2m cable.
Max air speed: 20 m/s.
138
ACCESSORIES
TA, Shunts, EW Box, INOX Box,
Copy Card, Transformers
TA Amperometric transformers with passing bar

TA current transformers are equipped with a passing bar
with a xxx/5 ratio for amperometric inputs on
AC amperometers and wattmeters above 10 A.
Models with 25/5 A, 40/5 A, 50/5 A, 60/5 A, 100/5 A,
150/5 A, 250/5 A, 400/5 A, 600/5 A and 1000/5 A ratios are
also available on request.
Model Class/Va /Bar

TA 25 A 0,5/5 Primary wind.
TA 40 A 0,5/5 Primary wind.
TA 50 A 3/1,5 23/30x10
TA 60 A 3/2 23/30x10
TA 100 A 1/3 23/30x10
TA 150 A 1/5 23/30x10
TA 250 A 0,5/6 23/30x10
TA 400 A 0,5/10 32/40x10
TA 600 A 0,5/15 32/40x10
TA 1000 A 0,5/30 40x20/50x15
Shunts Shunts with 60 mV voltage drop

SHUNTS devices with rated voltage drop of
60 mV that can be used when the amperometric input on
DC amperometers exceeds 10 A.
Model Capacity/Drop
SHUNT 25 A 25 A / 60 mV
SHUNT 50 A 50 A /60 mV
SHUNT 60 A 60 A / 60 mV
SHUNT 100 A 100 A / 60 mV
SHUNT 150 A 150 A / 60 mV
SHUNT 600 A 600 A / 60 mV
SHUNT 1000 A 1000 A / 60 mV
139
EW Box, INOX Box Instrument boxes
EW Box and INOX Box are a range of plastic and stainless
steel containers for wall mounting of instruments designed
for panel mounting.
EW Box without front panel

Front panel without holes in ABS for EW Box
Front panel in ABS for vertical EW Box, with 1 hole for 32x74 standard instruments and 1 hole for switches
Front panel in ABS for horizontal EW Box, with 1 hole for 32x74 standard instruments and 1 hole for switches
Front panel in ABS for vertical EW Box, with 2 holes for 32x74 standard instruments
Front panel in ABS for horizontal EW Box, with 2 holes for 32x74 standard instruments
INOX Box with 1 hole for 32x74 standard instruments
INOX Box with 2 holes for 32x74 standard instruments
INOX Box with 1 hole for EWTR 72x72 standard instrument
S
Copy Card Quick programming accessory
Copy Card is a quick programming accessory which quickly
uploads and downloads parameters from instruments using
a TTL serial connection.
This accessory can be used to upload and download data
and to reformat the card in order to be able to use it with
instruments configured with different parameter formats.
Transformers
The line includes a series of transformers enclosed in a plastic
housing, with mounting flange and screw terminals for leads
with a maximum diameter of 2.5 mm2 max.
Voltage [V] Power [Va]

230/12 3
230/12 5
115/12 3
24/12 3
230/12 11
140
Switches
Switches for ID and IC devices
Two-pole switches for ID and IC modules

Switches suitable to be used with Digifrost and universal
controllers.
These switches are available with lights in varying colors,
without lights and with light spots
Model Color
Two-pole switch Without light Grey key Grey frame 220V Silk-screening 0/1
Two-pole switch With light Full green light Grey frame 220V Silk-screening 0/1
Two-pole switch Light spot Green Grey frame 220V Silk-screening 0/1
Two-pole switch With light Full red light Grey frame 220V Silk-screening 0/1
Two-pole switch Light spot Red Grey frame 220V Silk-screening 0/1
Two-pole switch With light Full yellow light Grey frame 220V Silk-screening 0/1
Two-pole switch Light spot Yellow Grey frame 220V Silk-screening 0/1
141
Fan controllers
Single and Three-phase Fan Controllers
for EWCM series
Single-phase fan controllers for EWCM400

CF controllers are optional modules that can be connected to CF-REL for ON/OFF control
the main control modules and used to regulate the operation of CF-05 for control with phase cut-off, for maximum powers of
fans with currrents ranging from 2A to 10A. 500 W
The are designed in the form of "open cards" and are available CF-15 for control with phase cut-off, for maximum powers of
in several models: 1,500 W
CF-22 for control with phase cut-off, for maximum powers of
2200 W.
Technical Data of CF controllers

Protection class: IP00 (open card) Values and type of fuse
Electric connectors: FASTON CF-05: 5x20 2,5 A lagged
Power supply: 230V~ CF-15: 5x20 8 A lagged
Power used: depending on model CF-22: 5x20 12 A lagged
(500W/1500W/2200W).
Type of control signal: pulse modulated The fuse specified is the one recommended for a maximum load
Type of current on load: (and supplied as standard).
CF-05: 500 W max It is designed to protect the power components of the fan
CF-15: 1500 W max controller.
CF-22: 2200 W max It is never recommendable to install a fuse with a higher rating.
Max. absorption current: The rating of the fuse should be chosen in function of the load
CF-05: 2,5 A max current at 230 V~. that has to be controlled with the fan controller (the rating must
CF-15: 8 A max current at 230 V~. always be below the maximum one).
CF-22: 12 A max corrente a 230 V~. If correctly dimensioned, the fuse is also able to protect the
CF-22: 12 A max. current at 230 V~ load.
Three-phase fan controllers for EWCM400

DRV 300 12 A 420 V 1 Triac input (PWM) IP55 box
142
9 Electrical Measurements
A range of state-of-the art Multimeters

digital instruments for 9.1 IE 103 145
electrical measurements in 3 9.2 IE 123 146
9.3 IE 203 147
DIN format.
9.4 IE 303 148
These instruments can be
used to measure current,
voltage and frequency, with
or without relay outputs for
minimum or maximum load
or to manage the thresholds
of external loads.
144
IE 103, 103 LX
AC multimeters for indirect measurement

The IE 103 multimeter is an AC device for the indirect Front panel protection: IP40.
measurement of voltage, current and frequency. Casing: 3 module box for DIN omega rails
It can measure maximum voltages of 500 Va (20 Va min.) in
Mounting: on DIN omega rail
the 5065 Hz frequency range, maximum DC currents of 5
Aa (0.3 Aa min.) (directly ) and up to 1999 Aa (indirectly), if Operating temperature: 560 C.
used with external T.A., in the 5065 Hz frequency range. Storage temperature: 3075 C.
The multimeter can also measure frequencies up to 500 Hz Operating humidity: 1090% RH (non condensing).
(35 Hz min.).
Storage humidity: 1090% RH (non condensing).
The electric ranges to be measured can be configured with
a parameter. Refreshing frequency: 1Hz.
This multimeter can be fitted with a TTL serial port for the Harmonic content: third harmonic up to 30%, seventh
connection to TelevisSystem or, alternatively, to networks harmonic up to 10%.
with ModBUS protocol. The connection to this kind of Insulation class: 2.
networks requires, however, the use of the BusAdapter 150
Accuracy: 1% end of scale 1 digit,
TTLRS485 interface module.
For more detailed information, see section Systems, Consumption: 1.5 VA.
Accessories. Power supply: 230 Va.

456 AC indirect measurement
L
1415 Power supply
N
L Line
N Neutral
A 4 5 6
IE 103 A TTL input for TelevisSystem
7 8 9 10 11 12 13 14 15
145
IE 123, 123 LX
AC multimeters for indirect measurement
with two points of intervention

The IE 123 multimeter is an AC device for the indirect Front panel protection: IP40.
measurement of voltage, current and frequency, with two Casing: 3 module box for DIN omega rails
points of intervention.
The two digital outputs enable to manage the minimum and
maximum thresholds of external loads, for triggering or Operating temperature: 560 C.
alarms. Storage temperature: 3075 C.
It can measure maximum voltages of 500 Va (20 Va min.) in Operating humidity: 1090% RH (non condensing).
Storage humidity: 1090% RH (non condensing).
Aa (0.3 Aa min.) (directly ) and up to 1999 Aa (indirectly), if
used with external T.A., in the 5065 Hz frequency range. Digital outputs: 2 outputs on SPST 5(2)A 250Va relay.
The multimeter can also measure frequencies up to 500 Hz Refreshing frequency: 1Hz.
(35 Hz min.). Harmonic content: third harmonic up to 30%, seventh
The electric ranges to be measured can be configured with harmonic up to 10%.
a parameter.
This multimeter can be fitted with a TTL serial port for the
connection to TelevisSystem or, alternatively, to networks Accuracy: 1% end of scale 1 digit,
with ModBUS protocol. The connection to this kind of Consumption: 1.5 VA.
networks requires, however, the use of the BusAdapter 150 Power supply: 230 Va.
For more detailed information, see section Systems,
Accessories.

456 AC indirect measurement
L 1415 Power supply
N
1011 Relay 2 N.O.
1213 Relay 1 N.O.
A 4 5 6 L Line
IE 123 N Neutral
A TTL input for TelevisSystem
7 8 9 1 0 11 1 2 13 14 15
146
IE 203, 203
AC multimeters for direct measurement

The IE 203 multimeter is an AC device for the direct Front panel protection: IP40.
measurement of voltage, current and frequency. Casing: 3 module box for DIN omega rails
It can measure maximum voltages of 500 Va (20 Va min.) in
Aa (0.3 Aa min.) (directly ) and up to 1999 Aa (indirectly), if Operating temperature: 560 C.
used with external T.A., in the 5065 Hz frequency range. Storage temperature: 3075 C.
The multimeter can also measure frequencies up to 500 Hz Operating humidity: 1090% RH (non condensing).
(35 Hz min.).
Storage environment humidity: 1090% RH
(non condensing).
a parameter.
This multimeter can be fitted with a TTL serial port for the Refreshing frequency: 1Hz.
connection to TelevisSystem or, alternatively, to networks Harmonic content: third harmonic up to 30%, seventh
with ModBUS protocol. The connection to this kind of harmonic up to 10%.
networks requires, however, the use of the BusAdapter 150 Insulation class: 2.
Accuracy: 1% end of scale 1 digit,
Accessories. Consumption 1.5 VA.
Power supply: 230 Va.

456 456 AC direct measurement
L
N 1415 Power supply
L Line
N Neutral
A 4 5 6
IE 203
7 8 9 10 11 12 13 14 15
147
IE 303, 303 LX
DC multimeter for voltage and
current measurement

The IE 303 multimeter is a DC device for the direct Front panel protection: IP40.
measurement of voltage and current. It can measure Casing: 3 module box for DIN omega rails
maximum voltages of 500 Vc (20 Vc min.) and maximum
currents of 1999 Vc if equipped with 60 mV external
SHUNTS. Operating temperature: 560 C.
The electric quantities to be measured is selected by Storage temperature: 3075 C.
parameter. Operating humidity: 1090% RH (non condensing).
Storage environment humidity: 1090% RH
a parameter.
(non condensing).
This multimeter can be fitted with a TTL serial port for the
connection to TelevisSystem or, alternatively, to networks Harmonic content: third harmonic up to 30%, seventh
with ModBUS protocol. The connection to this kind of harmonic up to 10%.
networks requires, however, the use of the BusAdapter 150 Insulation class: 2.
TTLRS485 interface module. Accuracy: voltage 1% bottom scale 1 digit,
current 2% end of scale 1 digit
Accessories.
Consumption: 1.5 VA.
Power supply: 230 Va.

456 DC indirect measurement
+
- 1415 Power supply
- +

A 4 5 6
IE 303
7 8 9 10 11 12 13 14 15
148
10 Mechanical Controllers
Ranco mechanical controllers 10.1 O16/O52 for Temperature 151

for temperature, pressure 10.2 O16/O52 for Pressure 153
and humidity are suitable for 10.3 O17 155
10.4 P30 157
commercial refrigeration
10.5 K Series (1450, 22, 52, 5461) 159
applications. 10.6 Varifix 164
These controllers are 10.7 G Series (G60, G63) 165
available with adjustable or 10.8 J10J11 167
10.9 2001 Series (Paragon Defrost Timer) 168
fixed set point, depending on
10.10 V/VH Cycle reversing valves 169
the customers requirements, 10.11 T24/T25 Electronic Timers 171
and are approved by several 10.12 V16 (Solenoide valve) 173
international bodies.
These controllers are renown
for their reliability and
quality.
150
O16, O52
Thermostats for cooling and ambient air

016 and O52 are thermostats for room and commercial Electrical ratings: the electrical rating of the unipolar SPDT
refrigeration, equipped with a unipolar SPDT switch that switch is 16(16)A 250Va N.O. or N.C.; 1(1)A 250Va on the
opens or closes when the temperature increases or opposite side.
decreases. The tripping temperature can be adjusted by Compliance: all models are compliant with EN6073026
means of a screw on all versions, while the differential is and EN6073029, and manufactured in accordance with
adjustable on some models only. Thermostats can also be the requirements of standard ISO9001. These thermostats
equipped with a sensor to measure the air temperature, are also compliant with current European standards.
with straight capillary, with spiral capillary and remote bulb.
Terminals: 1 common, 2 opens the contact when the
Models with capillary, which enable temperature to be
temperature increases, 4 closes the contact when the
measured along the whole length, are used in applications
temperature increases.
in which the sensing element has a lower temperature as
compared to the thermostatic head; the straight capillary is Cable input: 14 mm insulating bushing for O16 and P.G. 16
more suitable for longer distances, while the spiral one is connector for O52.
recommended for smaller distances. Models with Coolants: suitable to be used with all types of gases.
remote bulb, in which temperatures are detected by the Mounting: two male holes on the rear of the controller for
sensing bulb only, are available with wide or narrow the insertion of M4x6 mm screws (supplied with the
differential. It is also possible to order models with an thermostat).
integrated disconnect switch if it is necessary to stop the Differential: the differential is the difference between the
plant without changing the settings of the thermostat. The enabling and disabling point of a variable. Given the
range also includes a model for ice refrigerators O16H6999 characteristics of the filling material of temperature
with fixed calibration, specifically designed to cyclically versions the differential may vary within the range of the
adjust the thickness of ice by means of a water-filled bulb thermostat.
sensor. The special version for anti-frost O16H8923 has a 6
Control: by means of hex nut with cutout for cross
m straight capillary that can be used to protect pipes, coils,
screwdriver, present both on the shaft of the capacity and
etc. from frost. This is factory preset to start at 2C and to
on that of the differential. There is also a control knob,
disconnect at 3.5C. For this model and for O16H6951, a
which is supplied as standard with some O52 temperature
model with manual reset button is also available. O16 and
controllers.
O52 models differ only by the class of protection that is
equivalent to IP66 for OH52 and to IP44 for O16.
Wiring Diagram
151
Dimensions 016
Dimensions 052
152
O16, O52
Single pressure controller for high or
low pressure

O16 and O52 are single mechanical pressure switches for Scale: p.s.i. and bar (bar only for T.U.V. models).
high and low pressure with unipolar SPDT switch, which Connections to pressure line: 7/16 20 UNF straight output
closes and opens when the pressure increases or decreases. male connector, 1/4 flared female connector.
These pressure switches can be supplied with automatic
Electrical ratings: the electrical rating of the unipolar SPDT
reset or manual reset button.
switch is 16(16)A 250Va N.O. or N.C.; 1(1)A 250Va on the
The tripping pressure can be adjusted by means of a screw
opposite side.
on all versions, while the differential is adjustable only on
models with automatic reset button. Some high pressure Compliance: all models are compliant with EN6073026
models have T.U.V. barometric capsules. Models with this and EN6073029, and manufactured in accordance with
configuration have a capsule enclosed in the capsule so the requirements of standard ISO9001. These thermostats
that the second capsule holds the coolant and stops the are also compliant with current European standards.
plant when a leak occurs in the operating capsule. Special versions only: USA (UL) and Canada (CSA) 17 FLA
Standard versions have a male flared fitting. It is also 102 LRA 250Va.
possible to order special versions with 1,000 mm integrated Terminals: 1 common, 2 opens when the pressure increases,
capillary with flared fitting and nut or versions with rigid 4 closes when the pressure increases.
tube (100 mm length, 6 mm diameter) when the thermostat
Cable input: 14 mm insulating bushing for O16 and P.G. 16
is brazed to the cooling plant. All versions without capillary
connector for O52.
can be equipped with a stainless steel fitting for ammonia.
O16 and O52 differ by their protection class: IP66 for O52, Coolants: suitable to be used with all types of gases.
IP33 or IP44 for model O16, depending on whether the Mounting: two male holes on the rear of the controller for
pressure switch is equipped with a manual reset button. the insertion of M4x6 mm screws (supplied with the
thermostat).
Wiring Diagram
153
Dimensions 016 Standard
154
O17
Dual pressure controllers for high and
low pressure

017 models are dual mechanical pressure switches for high Scale: p.s.i. and bar (bar only for T.U.V. models).
and low pressure with unipolar SPDT switch, which closes Connections to pressure line: 7/16 20 UNF straight output
and opens when the pressure increases or decreases. male connector, 1/4 flared female connector.
These pressure switches can be operated automatically both
Electrical ratings: the electrical rating of the unipolar SPDT
with high and low pressure, have a manual reset button
switch, except for versions with dual signal, is 16(16)A
for high and low pressure, and can be configured with
250Va N.O. or N.C.; 1(1)A 250Va on the opposite side.
automatic cycle for low pressure and manual reset for high
pressure. Model 017 with dual signal: transmitted with terminals 1
The tripping pressure can be adjusted by means of a screw and 4 as above; the maximum current between terminals
on all versions, while the differential is adjustable on models 12 and 13 is 0.1A 250Va.
with automatic reset. Some models have T.U.V. barometric Compliance: all models are compliant with EN6073026
capsules. and EN6073029, and manufactured in accordance with
Models with this configuration have a capsule enclosed in the requirements of standard ISO9001. These thermostats
the capsule so that the second capsule holds the coolant are also compliant with current European standards.
and stops the plant when a leak occurs in the working Special versions only: USA (UL) and Canada (CSA) 17 FLA
capsule. 102 LRA 250Va.
The 4000 model with dual signal enables to establish if the
Terminals of model O17 standard: 1 common, 2 opens when
compressor has been disconnected due to a high or low
the pressure increases, 4 closes when the low pressure
pressure. Standard versions have a male flared fitting. It is
increases and opens when the high pressure increases.
also possible to order versions with 1,000 mm integrated
capillary with flared fitting and nut or versions with rigid Terminals of model 017 with dual signal: 1 common 2 closes
tube (100 mm length, 6 mm diameter) when the thermostat the signal circuit when the low pressure decreases, 3 closes
is brazed to the cooling plant. the signal circuit when the high pressure increases, 4 closes
All versions without capillary can be equipped with a the signal circuit when the low pressure increases and
stainless steel fitting for ammonia. opens it when the high pressure increases.
Cable input: 14 mm insulated bushing.
Coolants: suitable to be used with all types of gases.
Mounting: two male holes on the rear of the controller for
the insertion of M4x6 mm screws (supplied with the
thermostat).
Wiring Diagram
155
156
P30
Differential pressure controllers for oil
Description Installation
P30 is a differential pressure controller for oil, suitable to
be mounted on refrigerating compressors with forced
lubrication. Its two capillaries enable it to detect the
pressure difference between the oil in the compressor
guard and the output of the oil pump.
When the lubrication pressure is too low and does not reset
within the relay delay, the differential pressure control trips
stopping the compressor.
To restart the compressor, it is necessary to press the
manual reset button. The range also includes models with
varying relay delays and pressure differentials.
Dimensions
157
Wiring Diagram
158
K14, K50
Adjustable thermostat with SPST switch

K50 is a cycling thermostat with a unipolar SPST switch that Temperature control range: the thermostat can be
closes when the temperature increases. K14 has the same configured according to the requirements of the customers
features of K50, but a narrower temperature differential for application.
special applications. Standard data is however listed below. Electrical rating of
The working range is adjustable while the differential is terminals 34: standard 6(6)A at 250Va, 12 A at 12 Vc.
fixed. Switch terminals: 6.3 mm or 4.8 mm.
It has small dimensions and is available both in standard
Material of the casing: zinc-plated and passivated cold
configuration and with mounting bracket. Fitted with
laminated steel.
capillary ranging from 300 to 3000 mm with varying coil
styles or bulbs. Variety of capillary lengths (in mm):
300/400/530/600/700/800/900/1100/1200/1500/2000/2500/
3000.
A model with remote bulb is available on request.
Temperature Diagram
Wiring Diagram
TYPICAL WIRING DIAGRAM

L
3
C
4
159
K22
Adjustable thermostat with SPDT switch

K22 is a cycling thermostat with 6 A (standard) or 16 A Temperature control range: the thermostat can be
(high capacity) unipolar SPDT switch. configured according to the requirements of the customers
The working range is adjustable while the factory preset application. Standard data is however listed below.
differential is wide or narrow. It has small dimensions and is Electrical rating of the switch: standard 6(6)A at 250 Va,
available both in standard configuration and with central high capacity 16(16)A at 250 Va.
upright.
Switch terminals: 6.3 mm.
Fitted with capillary ranging from 300 to 3000 mm with
varying coil styles or bulbs. Material of the casing: zinc-plated and passivated cold
laminated steel.
Variety of capillary lengths (in mm):
300/400/530/600/700/800/900/1100/1200/1500/2000/2500/
3000.
Wiring Diagram Temperature Diagram

L
3
C R
4 2
160
K52
and 2 probes

K52 is a cycling thermostat with unipolar SPST switch that Temperature control range: the thermostat can be configured
closes when temperature increases and 2 probes to manage according to the requirements of the customers application.
the enabling and disabling points. Standard data is however listed below.
It has small dimensions and is available both in standard Electrical rating of terminals: 34 6(6)A at 250 Va, 36 6(6)A
configuration and with mounting bracket. at 250 Va.
Switch terminals: 6.3 mm (standard).
varying coil styles or bulb.
Material of the casing: zinc-plated and passivated cold
This thermostat is available in 4 versions. laminated steel.
VERSION A: with fixed enabling point and adjustable Variety of capillary lengths (in mm):
disabling point. Available also with auxiliary switch to 300/400/530/600/700/800/900/1100/1200/1500/2000/2500/
disconnect the load and with an electric heater to maintain 3000.
the body of the controller at a higher temperature as A model with remote bulb is available on request.
compared to the capillary in applications that demand this
kind of requirement.
VERSION B: equivalent to version A, but with crossed
Temperature Diagram
enabling and disabling point.
VERSION C: with adjustable enabling and disabling points.
Available also with auxiliary switch to disconnect the load
and with an electric heater to maintain the body of the
controller at a higher temperature as compared to the
capillary in applications that demand this kind of
requirement.
VERSION D: equivalent to version C, but with crossed
enabling and disabling point.
Wiring Diagram

L
L
C R1
S1
3
4 6
161
K54
and LED switch

K54 is a cycling thermostat with unipolar SPST switch that Temperature control range: the thermostat can be
closes when the temperature increases and auxiliary LED configured according to the requirements of the customers
switch that closes or opens, depending on models, when application. Standard data is however listed below.
the alarm temperature is reached. Electrical rating of terminals: 34 6(6)A at 250 Va, 12A at
The working range is adjustable while the differential is 12 Vc; 36 0.1A at 250 Va, 12 Vc.
fixed. It has small dimensions and is available both in
Switch terminals: 6,3 mm standard, 4.8 and 2.8 mm available
standard configuration and with mounting bracket.
on request.
varying coil styles or bulb. Material of the casing: zinc-plated and passivated cold
laminated steel.
Variety of capillary lengths (in mm):
300/400/530/600/700/800/900/1100/1200/1500/2000/2500/
3000.

L
3
C S1
4 6
162
K61
Thermostat with SPDT switch,
switch for load disconnection and fixed
enabling point

K61 is a cycling thermostat with unipolar SPDT switch and Temperature control range: the thermostat can be
auxiliary switch connected in series to the main switch and configured according to the requirements of the customers
used to disconnect the load. application. Standard data is however listed below.
The disabling point is adjustable, while the enabling point is Electrical rating of switches: terminals 34 6(6)A at 250 Va,
fixed. terminals 32 0.2(0.2)A, terminals 36 6(6)A at 250 Va.
Thanks to this feature, the thermostat is able to
Switch terminals: 6.3 mm standard, 4.8 mm or 2.8 mm
automatically start the defrosting cycle every time the
available on request.
enabling temperature is reached.
It has small dimensions and is available both in standard Material of the casing: zinc-plated and passivated cold
configuration and with mounting bracket. Fitted with laminated steel.
capillary ranging from 300 to 3000 mm with varying coil Variety of capillary lengths (in mm):
styles or bulb. 300/400/530/600/700/800/900/1100/1200/1500/2000/2500/
3000.

L
L1
L2
C
3_ _ _ _ _ _
4 6 8
163
VARIFIX
Replacement thermostat

The Varifix family of replacement thermostats is designed Electrical ratings: 6 A inductive at 250 Va, except VW8 16 A
and packed to simplify field replacement of cooling at 250 Va.
controls. Note: models VS5/VR6 have a rating of 6 A 250 Va
Each Varifix model is coded for a specific type of cooling inductive on the power switch (terminals 3 and 4) and of
equipment. The Varifix code shown on each thermostat 0.1 A inductive 250 Va on the contacts of the signal switch
indicates the application for which it is suited. (terminals 6 and 3).
Note: model VTD9 has a rating of 6 A 250 Va inductive on the
General features
power switch (terminals 3 and 4) and of 0.2 A inductive
Multi-positional dial knob in 3 pieces for on-site
250 Va on the contacts of the change-over switch (terminals 3
calibration.
and 2).
Universal mounting bracket.
Kit with mounting screws, terminals tags and insulators.
Applications
VC1 (VL1) Refrigerator with compressor
Va1 (VL2) Absorption refrigerator
VF3 (VL3) Cell freezer for ice-creams
VP4 (VL4) Refrigerator with push-button enabled
defrosting
VS5 (VL5) Freezer - Standard signal
VR6 (VL6) Freezer - Reverse signal
VB7 (VL7) Bottle cooler
VW8 (VL8) Window air conditioner
VT9 (VL9) Cabinet refrigerator with 2 doors
VT93 Like VT9 with long capillary
VX0 Cabinet refrigerator with 2 doors
VTD9 (VLD9) Dual temperature refrigerator
with bypass valve
Wiring Diagram
VC1 VB7 VS5 VR6

VA2 VP4
VF3 VW8 L L
6 6
3 4
3 4 3 4
C C C
VX0/VT9 VTD9
C 4 C 2
6 3 4 6 3 3 4
164
G60, G63
Stationary Pressure controllers for high
and low pressure

These devices are stationary pressure controllers for G60 low pressure
refrigerating applications. They are available in two models:
Working range: fixed within the range; 10 Hg in vacuum
G60 for low pressure and G63 for high pressure.
conditions, 100 psi (0.357 bar).
Standard models come with SPDT switch and automatic
reset button. Models with SPST switch and manual reset Reset mode: automatic reset and manual reset (only for
button are also available. pressure increase).
This replacement thermostat comes with several pressure Maximum fixed pressure: 290 psi (20 bar), diaphragm 0.076
connectors: mm; 510 psi (35 bar), diaphragm 0.1/0.15 mm.
A) 7/16 20UNF female, Burst pressure: 1015 psi (70 bar), diaphragm 0.076 mm;
B) 7/16 20UNF male, 2030 psi (140 bar), diaphragm 0.1/0.15 mm.
C) 1/4 18NPT tapered male,
D) Welded fitting with 1/4 x 150 mm gasket,
E) 1/8 x 27NPT male, G63 high pressure
F) 7/16 20UNF female flared nut with 1 m capillary Working range: fixed within the range 100450 psi (731 bar).
G) 1 m capillary, 2 mm Reset mode: automatic reset and manual reset (only for
pressure decrease).
Maximum fixed pressure: 510 psi (35 bar).
Burst pressure: 2030 psi (140 bar).
Wiring Diagram
Cycle interruption with low pressure Cycle interruption with high pressure
165
Technical Specifications of G60, G63
Typical data Other Data
Differential: setting functions, see graphics. Working limits indoors: IEC529, protection standard against dirt
Coolants: compatible with all coolants and non corrosive gases. and humidity.
Ambient/switch head temperature range: 355 C. Version with automatic reset button: IP00 with 6.3 mm tag
terminals, protection class IP44, protection class IP66 and sealing
Maximum temperature of compressor head: 135 C.
disk.
Temperature range of the shipping environment: 3070 C.
Version with manual reset button: IP44 with visible reset button,
Switch: SPDT or SPST.
IP66 with covered reset button.
Switch power: a) 6(6)A 250V, b) 10FLA(40LRA) at 120 Va if used as
Insulation material: thermoplastic, flame class UL94V1, resistance
SPST on both contacts, c) 10FLA(40LRA) with a load of 120 Va
to traction ranging from KC400 to VDE0303.
1(1)A on the opposite contact if used as SPDT, d) 5A at 12 Vc
(inductive). Certifications: controls are compliant with all European, U.L. and
C.S.A requirements. Additional details are available on request.
Markings on the switch: 1 common, 2 cut-off for pressure increase,
3 cut-off for pressure decrease. Performance limits of the differential: several differentials,
depending on switches.
Dimensions
166
J10, J11
Humidity controllers

J10 and J11 are humidity controllers for the control of Humidity range: from 10 to 60% R.H., from 20 to 80% R.H.,
humidifiers and de-humidifiers, which can also be mounted from 30 to 90% R.H.
on walls and integrated in centralized plants. Differentials: 5% R.H. or 12% R.H.
The sensor in nylon fabric guarantees a response speed 12
Switch: SPDT or SPST.
times higher than that of sensors in nylon film. All models
come with differentials of 5 % or 12% of relative humidity Terminals: 6.3x0.8 mm.
and SPST or SPDT switches. The set point can be adjusted Function of the terminals (if present): 1 closes when relative
with the knob. humidity increases, 2 common, 3 closes when relative
humidity decreases.
Insulating material of the switch/casing: thermoplastic, fire-
Dimensions extinguishing class 94V0; resistance to creeping currents
600.
Certifications: compliant with standards IEC 607301 and
213, UL 873, CSA C22.2, No. 24.
Electric rating of the controller cycles: cycles of the circuit
breaker at 60 C 50000, cycles of shaft of the manual knob
6000.
Condition of ambient temperature: from 0 to 60 C (switch
head) and from 30 to 65.5 C (transportation).
Degree of protection of the casing: IP00.
Protection against electrical shocks: class 1.
Fixing method: screw, optional snap-on fixing mechanism
specified by the user.
167
Series 2000/3000
Defrost timers

Series 2000/3000 units are defrost timers with unipolar Line voltage (+10%/15%): 120 Va 50, 60 or 50/60 Hz;
SPDT switch. 208240 Va 50/60 Hz; 100120 Va 50/60 Hz.
The defrosting duration and ranges (4, 5, 6, 8, 10, 12, 16, 24 Input power: 1/4 or 2 W.
hours) are factory pre-set and cannot be changed by the
Output power: 1/3 or 1/2 Hp at 120, 208240 V; 10 or 15A
user. However, the user may adjust the cycle start time by
at 120 V; 5A at 208240 V; 125 VA pilot service; 16(6)A
means of a cam.
208240 V; 16(8)A 208240 V; 9(3.6)A 208240 V; 5(3.6)A
Timers are available in four models: series 2001 with
208240 V.
standard defrost cycles and input power of 2 Watt, series
2003 with short defrost cycle and input power of 2 Watt, Clutch: integrated in the timer, clockwise.
series 3001 with standard defrost cycle and input power of Types of cams: low with cutout for screwdrivers usable in
1/4 Watt, series 3003 for a short defrost cycle one direction only; knurled for medium heights, knurled for
and input power of 1/4 Watt. high heights.
The timer with short defrost cycles is used in applications in Mounting: two screws 620 type 25, two threading holes
which the timer motor is not running during defrost. 0.190 (4.8 mm).
The motor is powered after defrost when the defrost end
Ambient temperature: from 0 to 65 C (during use) and
device opens.
from 30 to 75 C (transportation).
Protection against dirt: suitable for environments with
normal pollution, compliant with standards EN60730.
Cutout: reinforced insulation (compliant with standards
EN60730) both in the cam-actuator and in the terminal
Dimensions areas. Component approved by UL, CSA and EN60730.
Timer motor wiring: from neutral to mains (shown), from
neutral to N.O. load, from neutral to N.C. load.
Wiring Diagram
168
V/VH
Cycle reversing valves

V and VH reversing cycle valves are used in all refrigerating SERIES V Valves
applications that require the reversal of the cooling flow.
Minimum/maximum pressure variation required to start the
These types of valves are generally used in heat pumps for
cycle reversal: 15/440 psi (400 psi for V12).
civil and industrial applications, but are widely employed
also in systems with hot gas defrosting functions and for Maximum working pressure: 680 psi (500 psi for V12).
special process applications. Minimum burst pressure: 2,500 psi.
Valves V and VH, compatible with traditional and new Maximum operating temperature 250 F (120 C).
coolants, offer a wide range of capacities ranging from
Minimum number of cycles: 135,000.
1,000 to 540,000 W and are available with connection pipes
with varying configurations and diameters. Mounting position: all.
Valves are equipped with L30 and LB coils and are available
with several combinations of ratings and different cable SERIES VH Valves
sizes.
Minimum/maximum pressure variation required to start the
reversal: 50/330.
Maximum operating pressure: 435.
Minimum burst pressure: 2,175 psi.
Maximum operating temperature 250 F (120 C).
Minimum number of cycles: 10,000.
Mounting position: horizontal.
Type of Pipe Connections
A B C
D E F
169
Flow Diagram of the Coolant
Coil energized Heating cycle Coil de-energized Cooling cycle
Coil energized Cooling cycle Coil de-energized Heating cycle
170
T24
Defrost timer with temperature
sensor

T24 are defrost timers in which the defrost cycle is enabled Contacts: 6.3x0.8 mm.
at a specific time (factory preset) or as soon as the defrost Power supply: 220/240 V, 50 Hz.
end temperature is reached. This condition is detected by a
Electrical rating of switch:
probe. These timers are also available in versions that delay
the start of the fans at the end of the defrost cycle. Terminals 23: 8(1)A at 240 Va, 12(2)A at 120 V,
Series T24100 Terminals 34: 6(6)A at 240 Va, 8(8)A at 120 V,
The start of the defrost cycle closes contact 23 that Terminals 35: 1(1)A at 240 Va, 2(2)A at 120 V.
enables the electric heater and opens contact 34 that
switches the compressor off. The defrost cycle ends at the
preset time or as soon as the defrost end temperature is
reached. At this time, the defrost electric heater is disabled
and the compressor is restarted.
Series T243000
This model has the same operating features of Series 100
models, except for the fact that the defrost electric
heater switches off at the preset time or as soon as the
defrost end temperature is reached. The compressor is
restarted only after the defrost time has elapsed.
Series T246000
This version, which is similar to Series 3000 models has an
auxiliary contact that delays the start of the fans as
compared to the compressor.
171
T25
Defrost timer

T25 are timers in which the duration of the defrost is Contacts: 6.3x0.8 mm.
factory pre-set. Power supply: 220/240 V, 50 Hz.
Series T25100
Electrical rating of switch:
The start of the defrost cycle closes contact 23 which
enables the electric heater and opens contact 34 that Terminals 23: 8(1)A at 240 Va, 12(2)A at 120V,
switches the compressor off. Terminals 34: 6(6)A at 240 Va, 8(8)A at 120V,
The defrosting cycle stops at the preset time. Terminals 35: 1(1)A at 240 Va, 2(2)A at 120V.
Series T255000
This series has the same operating features of Series 100,
but is equipped also with an auxiliary contact to delay the
start of the fans as compared to the compressor.
172
V16, L16
Solenoid valve

V16 valves are solenoid valves specifically designed for dual Minimum plant pressure: 400 p.s.i.
temperature refrigerators and for the defrost of Maximum temperature of body: 177 C (the valve body
domestic refrigerators. should not exceed this temperature during brazing).
These solenoid valves are enabled by a L16 coil, which is
Materials: body in brass, pipes in copper, pin in
available with voltages of 24, 115, 120, 220 Va/c.
nylon/Teflon.
Mounting: these valves should be mounted with the body
placed in vertical position and the coil on the top.
Coil: L16.
Pipe configuration: horizontal pipe (input), vertical pipe
(output, with the valve body placed vertically).
Examples of Applications
de-energized valve de-energized valve
de-energized valve
173
11 Product Selection Guide
11.1 Selection Guide for Controllers 175

11.2 Selection Guide for Refrigeration Controllers 177
174
Controllers
Casing IC 901 IC 902 IC 912(LX) IC 915(LX) IC 917(LX)
32x74
72x72 round casing, flush panel mounting
72x72 square casing
4DIN RAIL modules
Wall mounting
Power Supply
12 Va/c
24 Va
115 Va
230 Va
Analog Inputs
PTC probe
NTC probe
Pt100 probe
Ni100 probe
Thermocouples J, K
Voltage 01/510 V
Current 020/420 mA
EWHS 280/300/310
EWPA 007/030
Digital Inputs
1 programmable input (only LX)
Relay Outputs
1 relay
2 relay
Alarm relay (901/A)
12 Vc Auxiliary Output
Alarm repetition
Probes power supply
Analog Outputs
Signal repetition
Acoustic Alarm Signal

Buzzer (opt.) (opt.)
Serial Connection
Copy Card
TTL
ModBus (opt. LX) (opt. LX) (opt. LX)
TelevisSystem (only LX) (only LX) (only LX)
Type of function
ON/OFF
PID
Neutral zone
175
EWPC 800 WM 901 EWDR 902 EWDR 905 EWTR 910 EWTR 920 EWTR 930 EWTR 940
(902/T) (905/T)

(902/T) (905/T)
(902/T) (905/T)
(902/T) (905/T)
(902/T) (905/T)
(902/T) (905/T)
(902/R) (905/R) (EWHR) (EWHR) (EWHR)
(902/P) (905/P) (EWPR) (EWPR) (EWPR)
(901/A)

(901/B)
176
Controllers for Refrigeration
Casing ID 961 ID 961LX ID 970 ID 970LX ID 971

32x74
32x74 split + 4DIN modules
Open version
Wall mounting
Power Supply
12 Va/c
115 Va
230 Va
Analog Inputs
Thermostatic probe (PTC/NTC)
Defrost probe (PTC/NTC)
Auxiliary probe (PTC/NTC)
Digital Inputs
1 programmable input
2 programmable inputs
Relay Outputs
1 relay
2 relay
3 relay
Alarm relay (961/A) (961LX/A)
Alarms
HACCP (opt.) (opt.)
Buzzer (opt.) (opt.) (opt.) (opt.) (opt.)
Serial Connection
Copy Card
TTL
ModBus
TelevisSystem
RTC
LINK
177
ID 971LX ID 974 ID 974LX ID 975LX ID 983LX ID 985LX IS 972LX IS 974LX

(opt.) (opt.) (opt.) (opt.) (opt.) (opt.) (opt.)

(opt.) (opt.) (opt.) (opt.) (opt.) (opt.)

(opt.)

178
Controllers for Refrigeration
Casing EWTS 70 EWTS 72 EWTS 90 EWLT 24 EWLC 74 WM 961

32x74
32x74 split + 4DIN modules
Open version
Wall mounting
Power Supply
12 Va/c
115 Va
230 Va
Analog Inputs
Thermostatic probe (PTC/NTC) (NTC) (NTC) (NTC) (NTC) (NTC)
Defrost probe (PTC/NTC) (NTC)
Auxiliary probe (PTC/NTC)
Digital Inputs
1 programmable input
2 programmable inputs
1 Klixon input
Relay Outputs
1 relay
2 relay
3 relay
Alarm relay
12 Vc Auxiliary Output
Alarm repetition (961/A)
Alarms
HACCP
Buzzer (961/B)
Serial Connection
Copy Card
TTL
ModBus
TelevisSystem
RTC
LINK
179
Notes
181
182
Notes
183
184
Disclaimer
This document and its contents remain the sole property of Eliwell & Controlli S.r.l., and shall not be reproduced or
distributed without authorization. Although great care has been exercised in the preparation of this document, Eliwell &
Controlli S.r.l., its employees or its vendors, cannot accept any liability whatsoever connected with its use. Eliwell & Controlli
S.r.l. reserves the right to make any changes or improvements without prior notice.
Approvals related to the model, are available only for specific part numbers.
Contact the Sales Office for further information on details and availability.
185

Eliwell Kontrolori PDF

Uploaded by

Copyright:

Available Formats

Eliwell Kontrolori PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Eliwell Kontrolori PDF

Uploaded by

Copyright:

Available Formats

Index

1 Indicators temperature, humidity and pressure 10

2 Controllers temperature, humidity and pressure 18

4 Timers and Pulse Counters 44

5 Controllers for Refrigeration 50

6 Data Acquisition and Printing 104

9 Electrical measurements 150

10 Mechanical Controllers 150

11 Product Selection Guide 174

3.1 EWTN 970 37

4 Timers and Pulse Counters 44

5 Controllers for Refrigeration 50

Defrost Timers and

5.13 EWDR 981 67

5.17 IWC 720 73

5.21 IWP 740 LX 77

WM - Wall Mounting Controllers

Solutions for Refrigeration

6 Data Acquisition and Printing 104

6.1 PRINTWELL 1200 105

Monitoring and Remote Assistance solutions

Data Control and Acquisition Modules

8.1 Temperature Probes 135

9 Electrical Measurement 144

10 Mechanical Controllers 150

10.1 O16/O52 for Temperature 151

11.1 Selection Guide for Controllers 175

The range provides the Eliwell Meters

Description Technical Data

Wiring Diagram Description of Wiring Diagram

Description Technical Data

Wiring Diagram Description of Wiring Diagram

1 2 3 4 5 A TTL input for Copy Card and TelevisSystem

Description Technical Data

Wiring Diagram Description of Wiring Diagram

Description Technical Data

Description Technical Data

Description Technical Data

Wiring Diagram Description of Wiring Diagram

11 PTC Pt100 / Ni100 Pt100 / Ni100 420 mA TcJ / TcK

EWPA 007 EWHS 300 RH.

EWHS 31 T + RH EWHS 310 T + RH

Eliwell offers a complete IC - Universal Controllers

Description Technical Data

Wiring Diagram Description of Wiring Diagram

IC 901 - 12 V A 13 Relay N.O.

1 2 3 6 7 8 9 A TTL input for Copy Card

Warning: check the power supply specified on the

Description Technical Data

Wiring Diagram Description of Wiring Diagram

IC 901A - 12 V A 13 Relay N.C.

1 2 3 4 5 6 7 8 9 10 810 Probe input

Warning: check the power supply specified on the

Description Technical Data

Wiring Diagram Description of Wiring Diagram

Warning: check the power supply specified on the

Description Technical Data

Wiring Diagram Description of Wiring Diagram

Description Technical Data