WEST

A software application for calculating loads

and actions in compliance with
SNiP 2.01.07-85* and DBN- V.1.2-2:2006
User manual
Table of contents

Table of contents
1. General management ...................................................................................................... 3
1.1 Controls................................................................................................................................................. 3
1.2 Settings.................................................................................................................................................. 4
1.3 Menus.................................................................................................................................................... 5
1.4 Working with tables .............................................................................................................................. 6
1.5 Saving data............................................................................................................................................ 6
2. The WeST software application ..................................................................................... 7
2.1 Main window ........................................................................................................................................ 7
2.2 Settings.................................................................................................................................................. 8
2.3 Reference modes ................................................................................................................................... 9
2.3.1 Densities ............................................................................................................................................................9
2.3.2 Terrain ...............................................................................................................................................................9
2.3.3 Coefficients .....................................................................................................................................................11
2.3.4 Deflection limits ..............................................................................................................................................12
2.3.5 Operation life...................................................................................................................................................12
2.4 Design modes ...................................................................................................................................... 13
2.4.1 Self-weight ......................................................................................................................................................13
2.4.2 Temporary loads..............................................................................................................................................14
2.4.3 Wind ................................................................................................................................................................14
2.4.4 Wind. Pulsation ...............................................................................................................................................20
2.4.5 Full wind..........................................................................................................................................................21
2.4.6 Snow. Single-span buildings ...........................................................................................................................23
2.4.7 Snow. Two-span buildings ..............................................................................................................................25
2.4.8 Temperature.....................................................................................................................................................27
2.4.9 Ice glaze load on cables and ropes...................................................................................................................27
Design codes implemented by WeST ............................................................................................................. 29
Bibliography.................................................................................................................................................... 29

2
 General management

1. General management
1.1 Controls

Principles and controls that this software application uses provide a consistent user interface. The
application makes use of standard multi-tab dialog boxes. To switch to a page in a multi-tab dialog box, click the
respective tab at the top of the dialog. Additional controls and access methods include (see Figs. 1.1-1):
menus, which you open in the same way as those of any MS Windows1 applications, by clicking the left
mouse button (left-clicking);
functional buttons, clicking or pressing which (by placing the mouse pointer onto them and left-clicking
once) will activate certain functions, actions, or modes;
selection buttons or boxes of various kinds, which help make a choice from a number of suggested options;
text edit fields which you use to specify source data for analyses. All source data are numbers. If a non-
integer is to be entered, its integral part must be divided from its fractional part by period or another
separator. The separators are selected by the user as part of the system settings (see Settings | Regional
Settings | Number). In addition, scientific notation can be used to enter numbers, for example: 1.56-7;
drop-down or static lists, to select data items from;
tables, to enter and display tabular data;
dynamically digitized diagrams, where you can point at a functions argument and in this way have the
functions value displayed.

Menu

Edit field
Drop-down list

Selection
button

Checkbox

Functional button

Figs. 1.1-1. Controls of the application window

1
Microsoft, Windows are registered trademarks of Microsoft Corporation. All other mentioned trademarks are registered property of the
respective companies and corporations.

3
General management

1.2 Settings
The Settings dialog box can be called up at any time when working with the application. It is used to choose
general settings that affect the working session. Generally, the dialog contains the following tabs: Units of
Measurement, Report and Languages, Visualization and Profile Databases.
Each tab opens a property page that helps set up a particular
class of the applications settings.
The Units of Measurement tab (Fig. 1.2-1) defines what
measurement units will be used to describe physical quantities. It
contains two groups of data. The first one specifies units of
measurement for sizes of the construction in question, forces,
moment etc.
Compound units (such as moments of forces, pressure etc.) can
be defined by separately choosing their component units (for
example, force units and arm measurement units together define a
Fig.1.2-1. The moment unit).
Units of Measurement tab
To do it, use the button .
Second group helps choose the representation and precision of numeric data. Data representation is defined by
edit field controls where you specify the amount of significant digits in the fixed-point or scientific notation.
The data precision (the number of significant digits after the decimal point) is set using the buttons
(increase) or (decrease), while the button turns on the scientific notation. In addition, the respective edit
fields let you define what value of a certain unit of measurement should be interpreted as very small so that it is
displayed as 0 as soon as its absolute value is less than the specified threshold.
The Report and Languages tab (Fig. 1.2-2) lets you choose a
language in which to present all texts or captions in dialog boxes and
a final report.
To work with the report document, you can choose between the
View/Edit and Print modes.
When in the View/Edit mode, clicking the Report button in any
working window will bring the report on the screen for you to view
and edit it. An application associated with the RTF file format (Rich
Text Format) will be called up (such as MS Word Pad or MS Word).

Fig. 1.2-2. The Report and Languages tab

Obviously, it is the user who is responsible for any corrections made to the report (results of an analysis can be
edited, too).
There are differences in the RTF file formats used by the MS Word v.7 and MS Word 97 (2000) applications.
Therefore you can choose either format in the settings, in the Report Type mode. Clicking the Print button in the
Report group will print out the report in the form it has been generated by the application.
In the Headers/Footers field, you can indicate an RTF file name that contains desired headers and footers for
the pages of the report document. The file is selected from a standard list by clicking the button .2
The Paper Size lets you set up the size of paper on which to print the report (a drop-down list is used to select
the desired size).

2
If you wish to use MS Word to modify the header/footer RTF file shipped with the application, you need to remember it is not enough to
just enter a new text you have to use the menu item Tools|Language|Set Language and set Russian as the language for the newly entered text.

4
 General management

In addition, you can set indentation and page orientation for

the report document.
The Visualization tab (Fig. 1.2-3) has two groups of controls:
Colors and Fonts. Each group contains a list of controls and
displays their respective attributes (color and font). Double right
clicking opens a standard Windows dialog box for setting up the
color and font as desired.

Fig. 1.2-3. The Visualization tab

1.3 Menus
File The File menu contains two items: Menu and Exit.
Menu this item switches to the main window (it duplicates the button under the same name).
Exit finishes the working session.
Modes The Modes menu contains a list of all working modes available in the application and helps
switch to any of them without having to go to the main window.
Settings This menu is used to call up the Application Settings dialog box where you set up various
preferences of the application (it duplicates the respective button).
Tools While working, the user often wants to do some additional calculations. The Tools menu lets
you launch a standard Windows calculator application (provided it has been installed with the
system), a formula calculator, and a measurement unit converter.
Help This menu provides reference help on management and functionality of the application.

5
General management

1.4 Working with tables

Source data for the application are in most cases specified as tables (Fig. 1.4-1). To enter data in tables, follow
these rules:
tabular data are decimal numbers; what separator is used between the integral and fractional parts of a number
(a period or a comma) depends on the Windows environment settings;
in cases when the number of rows in a table is user-defined, the table has the buttons Add and Delete next to it;
the former lets you add a new row after the one currently selected, and the latter deletes one or more selected
rows;
to select (highlight) one or more successive rows, place the mouse pointer on No. of the first one, click and
hold the left mouse button, and drag the pointer over Nos. of the rows to be selected;
to switch between cells of the table, use the Tab (tabulation) key on your keyboard.
New rows will be added after the currently selected one, so if
you need to add one before the very first row of the table, follow
these steps:
highlight (select) first row of the table and click the Add
button to add a new row after it;
select first row of the table and press the Ctrl+Insert keys at
the same time; this will copy the first rows contents to the
Clipboard (a Windows memory buffer for copying);
select second (new) row of the table and press the keys
Shift+Insert together; this will put the contents of the
clipboard in the cells of second row, and now you can fill first
row with desired data.
Fig. 1.4-1. An example of a table The above steps can be used also to copy one or more selected
rows of a table.

1.5 Saving data

All analysis modes have the capability of saving the entered data in an external file. To do it, use the menu item
File|Save As when in the respective working mode. This will open a standard Windows dialog box for choosing a
directory and a file where to save the data. The filename and its extension are to be specified by the user.
To retrieve the saved data later, use the File|Open menu item.

6
 WEST

2. The WeST software application

The WeST application is used to perform calculations of loads and actions applied to structural constructions
in compliance with provisions of four regulatory codes: SNiP 2.01.07-85, which is an international document
among the CIS countries; SNiP 2.01.07-85* with an amendment as of 2003 N2 concerning snow loads which is in
effect in Russian Federation; DBN V.1.2-2:2006, which regulates loads and actions; and DSTU B V.1.2-3:2006,
which regulates deflections and displacements and is in effect in Ukraine.
The application implements only the most frequent loading cases, and also those for which the necessity to
comply with SNiP involves a complicated logic which often leads to mistakes as evidenced by practice.
In addition to this functionality, to some extent the WeST application is a reference manual which can be used
to check data concerning zoning of territories for loads and actions or to obtain other reference information.
Finally, the application can be used to accumulate structural concepts frequently applied by an engineer, in
order to create ones own reference data storage.
Further descriptions of the WeST functionality merge together general capabilities and focus only on most
significant features related to the implementation of differences or amendments in design codes. This is chiefly in
regard to the differences between two editions of SNiP [1, 2] and DBN [4]. DSTU [3] that regulates deflections and
displacements replaces Chapter 10 of both editions of SNiP [1, 2]; it contains no actual differences in comparison to
that Chapter.
We do not distinguish between SNiP 2.01.07-85 and SNiP 2.01.07-85* in our further description because they
are identical in the data that you have to provide and in the form in which the results are to be presented.

2.1 Main window

When the application is launched, it is its main window that
appears first on the screen (Fig. 2.1-1). The main window contains a
set of buttons for selecting a working mode. The modes can be
divided into two distinct groups:
reference modes ones used to get reference information and
to perform auxiliary actions of determining loads and actions;
design modes ones that implement calculations of
loads/actions in compliance with provisions of SNiP and DBN
(to select one, use the Design Codes drop-down list.
Subsequent sections provide detailed descriptions of each
available mode and differences between those caused by different
Fig. 2.1-1. The main window requirements in the design codes. Here we present only a brief
characterization.
The reference modes include:
Densities reference data concerning the densities of main building materials;
Terrain determining properties of loads that depend on where the construction site is situated
geographically;
Coefficients reference data on the safety factor for load, f ;
Deflection limits reference data on deflection/displacement limits as defined in the codes.
Operation life (as per DBN) reference data on the lifetime of buildings and engineering structures.
The group of design modes include:
Self-weight finding a value of the self-weight load from a multi-layer pack of different materials per unit of
area;

7
WEST

Temporary determining values of uniformly distributed temporary loads in various rooms, in compliance
with instructions from Table 3 of SNiP and Table 6.2 of DBN;
Wind calculating the static component of a wind load for structures of various types, from a set of those
listed in Annex 4 to SNiP and Annex I to DBN;
Wind. Pulsation calculating the static component of a wind load for prismatic structures, rectangular in
their plan, and determining the dynamic amplification factor through a procedure defined by SNiP;
Full Wind calculating wind loads allowing for a dynamic action of the pulsation component on vertical
prismatic and cylindric structures as per Sec. 9.4 through 9.13 of DBN;
Snow calculating a snow load on structures of various types from those listed in Annex 3 to SNiP and
Annex Zh to DBN;
Snow. Two-span buildings calculating a snow load on two-span buildings of various types from those
listed in Annex 3 to SNiP and Annex Zh to DBN;
Temperature determining temperature actions according to provisions of Section 8 of SNiP and Section 11
of DBN;
Ice on cables and ropes calculating loads caused by ice glaze and by wind acting on cables and ropes
covered by ice deposits in compliance with Section 8 of SNiP and Section 11 of DBN;
To exit to the main window from any of the modes, use the Menu button. Also, you can switch directly from
one mode to another by using the Modes menu of the application.

2.2 Settings
A specific feature in this particular application is that the button
is available in most modes. This is used to set a value for Safety
factor for load (f) (Fig. 2.2-1). The reason for this is that all
working modes make use of the factor f as recommended by the
respective provisions of SNiP and DBN. However, for some
Fig. 2.2-1, a. A safety factor for load (as per specialized structures (such as nuclear power objects) other values of
SNiP) f are recommended by other applicable design codes.
In one of those cases you should specify a different value in the
Safety factor for load, which will be used in calculation of the
design load values (the rated value will remain the same in each
case).
If you use the per SNiP button to set the factor, then in the
Snow and Wind modes the value f = 1,4 will be used, which is good
for all cases except for a snow load on buildings with light roofs (see
Paragraphs 5.7, 6.11 of SNiP 2.01.07-85*).

Fig. 2.2-1, b. A safety factor for load (as per

DBN)

8
 WEST

2.3 Reference modes

2.3.1 Densities
Tables of the Densities mode (Fig. 2.3.1-1) contain data taken from reference manuals and related to the
weight of unit of volume (or unit of area) of the following groups of building materials or structural parts:
covering/roofing parts;
steel decking;
heat insulation;
steam sealing;
water insulation;
fillings and coatings;
concretes and mortars;
other.
Choosing one of the groups using their respective radio buttons
will open a table that contains names, weights of unit of
volume/area, and safety factors for loads, all related to materials
according to recommendations of Table 2 of SNiP and Table 6.1 of
DBN.
The Modify button lets you enter new property values to
replace those suggested by the table. Clicking it will open the
Material dialog box (Fig. 2.3.1-2) that contains a name and
properties of the material from the row selected (marked) in the
table. The natural usage for this functionality is to edit or refine
previously specified data (for example, if the specifications have
been changed). The same result as the one you get by clicking the
Modify button can be obtained by double-clicking the left mouse
Fig. 2.3.1-1. The Densities dialog box
button on a table row that should be modified.
The Add button lets you supplement any of the reference tables
with additional rows that describe new building materials or
products. The name and properties of a new material should be
entered in the edit fields of the Material dialog box that opens when
you invoke the action.
Fig. 2.3.1-2. The Material dialog box To delete a material from the list, use the Delete button.

2.3.2 Terrain
In many cases, data concerning loads and actions are associated with the geographic location of a construction
site. These data can be searched for using the Terrain dialog box (Fig. 2.3.2-1) where there is a tree-like structure
of political division in the Find field of the dialog. If you select a construction site in the tree, the Results group
will display climatic data and its field Orientation will also display the respective map fragment. Using the Find
button, you can set up a search for the name of a political unit or a town of interest in the respective dialog box that
appears.
As the climatic territorial zones have fairly vague boundaries on maps, the boundaries are not assumed to
coincide with those of the political units, i.e. a political unit may not belong entirely to a certain climatic zone but be
divided between two zones. Large cities where intensive housing takes place are separated within the tree structure.
According to DBN, climatic actions for those can be explored more thoroughly through the zones loads and actions
defined by Annex E. The respective tabs of the modes have the button clicking which will open a dialog box
with a list of towns. Choosing a town and clicking the Apply button will put the refined characteristic value of the
action to the analysis source data fields.
9
WEST

After you indicate the location of the construction site, the

fields of the Results group will show the following data:
No. of snow zone (Map 1* of Annex 5 to SNiP, Fig. 8.1 in
DBN);
No. of wind zone (Map 3 of Annex 5 to SNiP, Fig. 9.1 in DBN);
No. of ice glaze zone (Map 4 of Annex 5 to SNiP, Fig. 10.1 in
DBN);
average wind velocity in the winter (Map 2 of Annex 5 to
SNiP);
average month temperature in July (Map 6 of Annex 5 to SNiP);
average month temperature in January (Map 5 of Annex 5 to
SNiP);
Fig. 2.3.2-1. The Terrain dialog box geographic latitude used to determine the maximum sun
radiation value (SNiP 2.01.01-82);
deviation of average day-and-night temperatures from the average month ones as defined by SNiP;
No. of wind zone for a gust-and-glaze load (Fig.10.2 in DBN).
All these values can be modified by the user; to do so, make a selection in a drop-down list.
Click the Apply button to store the selected values for the future use by the design modes of the application.

10
 WEST

2.3.3 Coefficients
This mode is used to get reference information concerning
values of safety factors for load, f, defined by SNiP and DBN. The
Constructions and soils tab (Fig. 2.3.3-1) presents values from
Table 1 of SNiP and Table 5.1 of DBN, and the Equipment tab
(Fig. 2.3.3-2) those from Table 2 of SNiP and Table 6.1 of DBN.
The Climatic loads tab (Fig. 2.3.3-3) provides reference
information concerning the safety factors for load, f, for wind,
snow, and combined gust-and-glaze according to DBN, which
depend on the service life, the degree of responsibility of a structure
or building, and the time of operation during which the limiting
inequalities of the second limit state group could be violated.
The safety factors for load are based on provisions of the
Fig. 2.3.3-1. The Coefficients dialog box following DBN clauses:
The Constructions and soils tab for wind load 8.11, 8.12;
for snow load 9.14, 9.15;
for gust-and-glaze load 10.10, 10.11.

Fig. 2.3.3-2. The Factors dialog box

The Equipment tab

Fig. 2.3.3-3. The Factors dialog box

The Climatic loads tab

11
WEST

2.3.4 Deflection limits

This mode is used to get reference information concerning
values of vertical deflection limits (Fig. 2.3.4-1), and horizontal ones
caused by cranes and wind, as defined in Tables 19, 21, 22 of SNiP
and Tables 1, 3, 4 of DSTU.

Fig. 2.3.4-1. The Deflection Limits

dialog box
The Vertical deflections tab

2.3.5 Operation life

This mode is used only when working with DBN. It provides
reference data on the service life of structures and buildings in
compliance with Annex V of DBN (Fig. 2.3.5-1). This information
is required to set the safety factors for load, f, for snow, wind, and
gust-and-glaze loads.

Fig. 2.3.5-1. The Operation Life dialog box

12
 WEST

2.4 Design modes

2.4.1 Self-weight
The Self-weight mode is used to calculate loads caused by the
self-weight of a pack composed of multiple layers of different
materials. This functionality is implemented in the respective dialog
box (Fig. 2.4.1-1) where the left half contains a table of materials
and the right one contains a table that lists selected materials
included in the pack.
To specify each layer of the pack, you should select a group to
which the material of the current layer belongs. To do this, select a
radio button of the respective group (covering parts, steel decking,
heat insulation, steam sealing, water insulation, fillings and coatings,
concretes and mortars, other). After selecting a group, you will see a
list of materials contained in it, in the left table. Each row of the
table contains a materials title, its volume weight or that of unit of
Fig. 2.4.1-1. The Self-weight dialog box area of a ready-made construction part, and a value of the safety
factor for load according to Paragraph 2.2 of SNiP and
Paragraph 6.2 of DBN.
Using the upper button lets you carry the material over
from a selected (highlighted) row of the left table to the right
(working) table where in this way you are accumulating the pack.
If the thickness of layers is fixed and may not be changed, the
respective row of the table will contain a blank dash. Otherwise,
double clicking on a desired row of the working table lets you enter
the layer thickness data in the Thickness column.
The composition of the pack defined in the working table can
be edited using the Delete and Modify buttons. If the pack that you
have entered is a typical or standard one, you can store it under a
convenient name of your choice using the Save pack button.
Fig. 2.4.1-2. The Pack dialog box Clicking the button will open a dialog box (Fig. 2.4.1-2) where you
specify a name for the pack.
The saved pack will be added to the Packs list, so afterwards it
can be retrieved from that list into the working table using the lower
button, . The pack can be supplemented with new layers, or
some of the layers can be removed from it.
Clicking the Calculate button will display the respective values
of the load per unit of area caused by the packs self-weight in the
Rated load and Design load fields (for SNiP) or in Operation load
and Limit load fields (for DBN).

13
WEST

2.4.2 Temporary loads

This mode (Fig. 2.4.2-1) implements functionality for choosing
uniformly distributed temporary loads on floor panels, stairways,
floors etc. in compliance with Paragraphs 3.5 to 3.9 of SNiP and
Paragraphs 6.5 to 6.9 of DBN.
The mode determines full and lowered values of the rated and
design loads (for SNiP), characteristic and quasi-permanent ones
(for DBN) using lowering factors that allow for a loaded area one
actually subjected to the load (see Paragraph 3.8 of SNiP and
Paragraph 6.8 of DBN) and combination factors that take into
account the number of loaded floor panels in multi-storey buildings
(see Paragraph 3.9 of SNiP and 6.9 of DBN).
A room type is selected in the Buildings and rooms list. A
type of structure for which this analysis is performed can be selected
Fig.2.4.2-1. The Temporary loads by one of the respective radio buttons.
dialog box To obtain the load value, click the Calculate button; this will
display rated and design load values (for SNiP), or operation, limit,
and quasi-static loads (for DBN).

2.4.3 Wind
This mode is used to calculate a wind load on some of the
buildings, structures, and structural parts the designs of which are
presented in Annex 4 to SNiP and in Annex I of DBN. In all cases
this mode determines a static value of the wind load normal to the
structures surface. A two-tab dialog box entitled Wind is used to
enter source data and get the results.
Its first tab, General (Fig. 2.4.3-1), is used to enter information
concerning a terrain type and wind zone in which the object of
interest is situated. The Wind zone list and the Rated value of wind
pressure field (SNiP) or Characteristic value of wind pressure
(DBN) retrieve their values from the Terrain dialog box (if the
Apply button has been clicked in the latter). However, if the user
desires so, he can choose a wind zone independently from the
Fig. 2.4.3-1. The Wind dialog box respective list. If a rated value of the wind pressure is different from
The General tab that specified in regulations, then the list will not show the wind
zones name.
If you are using DBN as a working code, the button will provide access to a list of cities of Ukraine that
lists refined data (based on Annex E) concerning the characteristic load values. Selecting a desired city and clicking
the OK button will carry the loads characteristic value over to the source data.
The terrain type is selected in the respective list. To set a structures type, use the available group of radio
buttons.
After you have entered all the required data on the General tab, switch to the next one, Calculate wind load
(Fig. 2.4.3-2), where you specify additional source data needed for the analysis and where you get the result. Below
there is a description how this window looks when working with various types of structures.
The sign convention for the wind pressure used with all types of structures is established in compliance with
rules from Paragraph 6.6 of SNiP and 9.8 of DBN: the positive wind pressure is such that it is directed towards the
surface in question, and the negative pressure is one directed away from the surface.

14
 WEST

Limitations of the implementation

For all structures (except for canopies) and walls of buildings,
a variation of the winds velocity head with elevation is taken into
account. It is assumed for all roofs that the wind load does not vary
over their height; it maintains the value defined for the top of the
roof.

Vertical surfaces and ones When this type of structures is selected (Scheme 1 from
declined from vertical by no Annex 4 to SNiP or Annex I to DBN), in the Calculate wind load
more than 15 tab (Fig. 2.4.3-2) you enter the height of the structure, , and specify
a scanning step for the result (its value is preloaded by default).
From a drop-down list available in this window, you choose a type
of the surface (windward, leeward) for which the wind load should
be calculated.
The result window displays a plot of the load vs. height. This
plot can be dynamically digitized, i.e. when you point at a certain
height the screen shows the respective load value. The heights will
correspond to the scanning step selected before.
Green points (marks) on the ordinate axis indicate at what
intermediate points this calculation takes place. The spacing between
them conforms to the specified scanning step. The marks can be
deleted and restored by moving the mouse pointer onto them and
left-clicking. Wind pressure values in locations with marks that
Fig. 2.4.3-2. The Calculate wind load tab remain undeleted will be displayed in a table generated when you
click the Table button and then shown in the Results dialog
(Fig. 2.4.3-3).
The Select all and Clear buttons let you, respectively, include
all points that conform to the scanning step in the table (plot) or
remove those from that.
There are zooming buttons on top of the load plot. The plus
sign marks the zoom-in button clicking which will double the plot
every time. The minus sign button is used to zoom out the picture
and becomes accessible only after the plus button is clicked. To
return to the original size of the plot, just click the equal button,
and youll be back in one step.
Similar buttons are used in all modes where there are plots of
loads.

Fig. 2.4.3-3. The Results dialog box

15
WEST

Single-span buildings For buildings of this type (Schemes 2 from Annex 4 to SNiP
with no skylights or Annex I to DBN), the Calculate wind load tab (Fig. 2.4.3-4)
requires the sizes of the building. A drop-down list available here is
used to select a surface type (roof, left wall, right wall, side walls)
for which to calculate the wind load, and there are options of the
design wind direction to choose from.

Fig. 2.4.3-4. The Calculate wind load tab

Single-span buildings with If this type of structures is selected (Schemes 9 from Annex 4
no skylights, permanently to SNiP or Annex I to DBN), the Calculate wind load tab requires
open on one side (Fig. 2.4.3-5) sizes of the building. Use a drop-down list to choose
a surface type (roof, left wall solid, right wall permeable, side
walls) for which to calculate the wind load. Select also a wind
direction for the analysis.
In this case we deal with a simultaneous action of the wind
pressure outside and inside the building, so the result will be an
overall load on the selected surface.
The aerodynamic coefficient of internal pressure, Ci, at a given
permeability between 5% and 30%, will be calculated by
interpolating between limit values indicated in Schemes 9 of
Annex 4 to SNiP or Annex I to DBN.

Fig. 2.4.3-5. The Calculate wind load tab

16
 WEST

Buildings with vaulted and

geometrically similar roofs If this type of structures is selected (Schemes 3 from Annex 4 to
SNiP or Annex I to DBN, the Calculate wind load tab (Fig. 2.4.3-6)
will require sizes of the building. Use the drop-down list to select a
surface type (roof, left wall, right wall, side walls) for which to
calculate the wind load. Select also a direction of the wind for the
analysis using the radio buttons.

Fig. 2.4.3-6. The Calculate wind load tab

Canopies For this type of structures (Schemes 11 from Annex 4 to SNiP

or Annex I to DBN) you should use controls on the Calculate wind
load tab (Fig. Error! Reference source not found.-7) to choose a
design of the canopy, enter sizes, and select a wind direction to use.
The load on the roof will be represented as a plot with which
you can do a dynamic digitizing. However, instead of selecting an
elevation of the point of interest, you choose its ordinate on the
roofs horizontal projection.

Fig. 2.4.3-7. The Calculate wind load tab

17
WEST

Cylindric tanks
If this type of structures is selected (Schemes 12, b from
Annex 4 to SNiP or Annex I to DBN), the Calculate wind load tab
(Fig. 2.4.3-8) will require sizes of the building. Use the drop-down
list to choose a surface type (spherical roof, elevation of a wall, plan
of a wall, internal pressure) for which to calculate the wind load. Use
radio button controls to indicate a wind direction to be used.
This version of the application does not deal with conical roofs,
therefore the roof surface is specified as spherical.
As the internal pressure can take place only if there is no roof or
if the floating roof is in its lower position, the internal pressure
values are presented here separately without being summed with the
external pressure on the wall. Which design case to choose (either
the overall value or the separated ones) is up to the user, who also
has to consider various options of the tanks filling which means
Fig. 2.4.3-8. The Calculate wind load tab where (at what elevation) the internal pressure begins.
The distribution of the pressure over the tanks surface is
described by two plots:
in a horizontal plane at the level defined by the h property
Wall (in plan) which is included in the Surface drop-down
menu;
on a vertical, the position of which is determined by an angle, ,
between a radius that crosses the vertical and the horizontal axis
Wall (elevation) in the Surface drop-down menu.
Depending on which of the plots has been selected, the result
will be:
a distribution of the wind pressure across the plan at a given
elevation;
a variation of the wind pressure with height in a given position
of the vertical.

18
 WEST

Extended structures and

elements with cylindrical For structures of this type, unlike ones described before, the
surfaces load is referred to unit of length rather than to unit of area. After you
select this type of structures (Schemes 14 from Annex 4 to SNiP or
Annex I to DBN) in the Calculate wind load tab (Fig. 2.4.3-9) you
need to specify the height and diameter of the structure, and choose a
surface type from a drop-down list (wooden, steel,
concrete/ferroconcrete, masonry) thus defining the surfaces degree
of roughness, . If necessary, this property can be entered explicitly
in the respective edit field.
The result of the calculation will be represented as a plot of the
load per unit of line vs. elevation. This plot can be dynamically
digitized, i.e. when you point at an elevation with the mouse pointer,
you get the load value displayed on the screen.

Fig. 2.4.3-9. The Calculate wind load tab

Limitations of the implementation

The wind pressure value depends on Reynolds number, Re, for
which SNiP and DBN specify a range of values up to Re = 3,2106.
When the limit is exceeded, the value of the aerodynamic
coefficient, Cx, is assumed to remain constant.
The relative roughness property, /d, is determined by linear
interpolation between plots presented in Table 14 of Annex 4 to
SNiP or Annex I to DBN. In the cases of /d < 10-4 and /d > 0,05
the value of Cx will be determined by the ultimate curves.

Oblique tubular elements

When this type of structure is selected (Schemes 18 from
Annex 4 to SNiP or Annex I to DBN) the Calculate wind load tab
(Fig. 2.4.3-10) requires sizes of the element and a wind direction. As
in the previous case, here a load per linear unit will be determined,
and only a component perpendicular to the elements axis is under
consideration.
The sign convention for loads: a load is assumed to be positive
if its projection onto the vertical is downward, i.e. if the weight and
wind effects are added up.
The result of the calculation is presented in the form of a linear
load vs. elevation plot. The plot can be digitized dynamically, i.e.
you can point at an elevation to see its respective load value.

Fig. 2.4.3-10. The Calculate wind load tab

19
WEST

2.4.4 Wind. Pulsation

This mode is used to calculate a wind load on a building or
structure which is prismatic and rectangular in its plan and has a
constant stiffness along its height; this includes also structures that
can be simulated by this model approximately (Scheme 13 in Annex
4 to SNiP).
Unlike the Wind mode (see above), this one does more than
evaluation of a static wind load. The mode also evaluates a dynamic
pulsation effect and gives recommendations on whether a detailed
dynamical analysis is required. In addition, it gives an estimate of
the dynamic amplification factor which can be the basis for making
the decision whether a detailed analysis is really necessary and
whether the pulsation component should be taken into account.
Fig. 2.4.4-1. The General tab

Special feature of the implementation

The pulsation component of the wind load is calculated in
compliance with Paragraph 6.7 c of SNiP; the calculation also
complies with a requirement of Paragraph 6.8 that the inertia forces
should be taken into account if the oscillation takes place at a
frequency greater than the ultimate one.

A two-tab dialog box entitled Wind. Pulsation is used to enter

source data and obtain results.
Its first tab, General (Fig. 2.4.4-1), is used to enter information
related to a terrain type and wind zone where an object of interest is
situated. The Wind zone list and the Rated value of wind pressure
field retrieve their values from the Terrain dialog box (if the Apply
button has been clicked in it). However, the user may choose a wind
zone independently from a list. The terrain type and the structure
type are also selected using the respective lists.
The same tab is used to specify these data: sizes of the
buildings plan, its height, the weight of the building per running
meter of elevation (allowing for the weight of floor panels and
Fig. 2.4.4-2. The Calculate wind load tab sustained live load), average elasticity modulus of the material of
load-bearing constructions. You also need to specify: principal
moments of inertia with respect to the U, V axes, and slopes of the
U, V axes with respect to Y, Z along which the wind load acts.

It is possible to define the geometric properties of a building using the TONUS application. Values calculated
by the TONUS software are retrieved from a file with the .tns extension (the button ).
The building should be rectangular in its plan. Obviously, a lot of real buildings and structures can be assumed
rectangular only as approximation, so the results of the analysis will be also approximate.
If the exterior contour of a building is made up by fencing rather than load-bearing constructions (as in
skeleton buildings), the moments of inertia can be found in the same way as for a multi-point cross-section. To use
the TONUS application for this purpose, you will need to specify the plan locations and sizes of cross-sections of
all load-bearing parts.

20
 WEST

Note that an accurate calculation of the pulsation component in compliance with Paragraphs 6.7 to 6.9 of SNiP
requires that we know modes and frequencies of natural oscillation, i.e. a detailed information regarding the whole
structure. The WeST application determines those as if the structure were a cantilever bar with a constant stiffness
along its elevation equal to that of a bar that has a cross-section bounded by the load-bearing walls of the building.
After you have entered all the data in the General tab, switch to the next one, Calculate wind load (Fig. 2.4.4-
2) where you specify:
a wind direction (on a wall of size b, on a wall of size d, or diagonally);
a number of fragments into which the building will be divided along its elevation and on which the results will
be obtained (see Paragraph 6.7 c in SNiP).
The result of the calculation is represented as a plot of the wind loads static component (its rated and design
values) vs. elevation. The plot can be digitized dynamically, i.e. you can point at an elevation to get the respective
load value displayed on the screen.
The additional results of the calculation include two dynamic amplification factors:
one for displacements, being an averaged ratio of the wind loads pulsation component to its static component;
one for total bending moment at the base, being a ratio of the pulsation component of the bending moment at
the base of the building to the respective static value.
Having these values permits the user to make a decision whether to perform (or not perform) a detailed
dynamic analysis of the structure. Generally, the dynamic analysis is not reasonable if the dynamic amplification
factors are less than 0.2, while such analysis is a must if these factors are greater than 0.4.
To provide an additional check, this tab gives also higher periods of the natural oscillations in the U and V
planes.

2.4.5 Full wind

This mode calculates dynamic wind loads and takes into
account a dynamic effect of the pulsation component for vertical
prismatic and cylindric structures no more than 200 m high with a
nearly constant stiffness along the height, as defined by
Paragraphs 9.4 through 9.13 of DBN. The projection of the structure
onto the vertical plane in the direction perpendicular to the wind
action plane must conform to Schemes 13, 14 in Annex I to DBN.
Unlike the Wind mode (see above), this mode evaluates the
dynamic effect of the pulsations and their mutual correlation over
height in addition to the static wind load.

Fig. 2.4.5-1. The General tab

Special feature of the implementation

To calculate the wind load according to Paragraphs 9.4 through
9.13 of DBN, the direction factor Cdir and the relief factor Crel are set
to 1,0.

The Full Wind dialog box is used to enter source data and get
the results.
The first tab, General (Fig. 2.4.5-1), is used to enter
information concerning the terrain type and the wind zone where the
object of interest is situated. The Wind Zone list and the
Characteristic value of wind pressure field receive values from the
Terrain dialog box (if the Apply button has been clicked there).
21
WEST

However, you can choose the wind zone independently from a list.
The button provides access to a list of Ukrainian cities which
contains refined data (based on Annex E) concerning the
characteristic value of the load. If you choose a desired city and click
the OK button, the characteristic value will be copied to the source
data automatically. To set up the terrain type and the structure type,
use the respective lists.
The same tab is used to specify the sizes of the building in its
plan, in the direction perpendicular to the wind action plane, and its
height.
The building or structure must be rectangular or round in plan.
Many actual structures can be represented by such a model
Fig. 2.4.5-2. The approximately, so the result of the analysis will be an approximation,
Calculate wind load tab too.
The Calculate wind load tab (Fig. 2.4.5-2) presents results of
the calculation as a plot where the full wind load (its operation and
limit value) varies vs. the elevation. This plot can be dynamically
digitized, i.e. when you point at an elevation with the mouse pointer,
you get the load value displayed on the screen.

22
 WEST

2.4.6 Snow. Single-span buildings

This mode is used to calculate a snow load on single-span
buildings with the roof profiles conforming to Schemes 1, 2, 3, 10
from Annex 3 to SNiP or Annex Zh to DBN.
The Source data tab (Fig. 2.4.6-1) is used to enter information
about the roof profile and the snow zone in which the object of the
analysis is situated. The Terrain data group has a drop-down list
that you use to select a snow zone; next, its respective rated (SNiP)
or characteristic (DBN) snow load value will be assigned. In
addition, for the purpose of the analysis you need to specify an
average January temperature and an average wind velocity in the
winter (only for the SNiP-compliant analysis).
All weather data will be filled in automatically if you have
selected a snow zone and clicked the Apply button in the Terrain
Fig. 2.4.6-1. The Source data tab dialog box. If the working code is DBN, the button provides
access to a list of cities of Ukraine that contains refined data (based
on Annex E) concerning the characteristic values of the load.
Selecting a desired city and clicking the OK button will carry the
characteristic load value over automatically to the source data set.
The profile of the buildings roof is selected using functional
buttons that depict respective profiles available. To have the analysis
done, click the Calculate button or point at the Snow load tab.
For a single-pitched roof (Fig. 2.4.6-2), there is defined only
one way of applying the load; rated and design values are available
for it in the SNiP analysis, as well as operation and limit values in
the DBN analysis.
For a double-pitched roof (Fig. 2.4.6-3), there can be either one
or two load application schemes (depending on the roofs slope); for
Fig. 2.4.6-2. The Snow load tab each one you can get the loads respective rated and design values
(single-pitch roof) (SNiP) or its operation and limit values (DBN).

Fig. 2.4.6-3. The Snow load tab

(double-pitch roof)

23
WEST

For a roof that has a vaulted or similar configuration

(Fig. 2.4.6-4) there are three load application schemes, and for each
one a distribution plot will be displayed. This plot can be scanned
(dynamically digitized) in the similar way as was described earlier in
the section discussing the wind loads.

Fig. 2.4.6-4. The Snow load tab

(vaulted roof)
For a roof that has a longitudinal skylight (Fig. 2.4.6-5), there
exist two load application schemes. A load distribution plot will be
displayed for each of those.

Fig. 2.4.6-5. The Snow load tab

(longitudinal skylight)
For a roof that has parapets (Fig. 2.4.6-6), there can be only one
load application scheme. A load distribution plot will be displayed.
In the case when the snow load near the parapet must not be
taken into account, the load plot will have zero values.

Fig. 2.4.6-6. The Snow load tab

(a roof with parapets)

Limitations of the implementation

For Scheme 3 (one that defines buildings with longitudinal
skylights), the snow load is determined only in the skylight area
(area C in designations of SNiP and DBN).
Note 3 to Scheme 3 is not implemented.

24
 WEST

2.4.7 Snow. Two-span buildings

This mode is used to calculate the snow load on two-span
buildings, the roof profiles of which conform to Schemes 4, 5, 6, 7,
8 in Annex 3 to SNiP or in Annex Zh to DBN.
Two-span buildings are constructed by selecting designs for
their left and right spans. Generally, each of the spans can have one
of two single-pitch roofs (right or left inclined), a double-pitch, a
double-pitch with a longitudinal skylight, or a vaulted roof. This
produces 25 different possible designs of a two-span building.
Every two-span building may have a height difference at the
boundary between its spans. The difference is counted from the
ultimate right point of the left spans roof to the ultimate left point of
the right spans roof. In all cases it is assumed that the left roof is
not lower than the right one.
Fig. 2.4.7-1. The Design tab The height difference will be determined automatically when
analyzing source data of a selected design.
In cases when there is no height difference or it is less than a
minimum value defined in Note 3 to Scheme 8, no additional load
from the snow bag to the right (lowered) roof is taken into account.
In cases when the two-span building is constructed of two
single-pitch roofs with their pitches equally oriented (shed roofs in
compliance with Scheme 4 of Annex 3 to SNiP or Annex Zh to
DBN), the snow load will not depend on the height difference
between the spans.
For two-span buildings (double-pitch and vaulted), in cases
when the height difference is either zero or not taken into account
according to Note 3 to Scheme 8 of Annex 3, the snow load will be
determined using Schemes 5 and 6 of Annex 3.
In all other cases the snow load will be determined by Scheme 8
of Annex 3 to SNiP or Annex Zh to DBN.
The calculation produces a snow load on the projections of the
right and left spans of a two-span building; in necessary cases, it
produces also an additional load (caused by a snow bag) on the right
building.
The mode contains three property tabs:
Design;
Source data;
Snow load.
The Design tab is used to select a buildings design and specify
source climatic data common for the whole building. Two-span
buildings are constructed by choosing designs for the left and right
spans from the respective drop-down lists. A design of the building
that has been constructed (Fig. 2.4.7-1) will be displayed in the
central part of the tab.
The Terrain data group contains a drop-down list where you
choose a snow zone; this will assign a proper value to the snow load
automatically a rated one (SNiP) or a characteristic one (DBN).
To complete the analysis, you will need also to specify an average
temperature in January and an average wind speed in the winter
(SNiP-compliant analysis only).

25
WEST

All weather data will be filled in automatically if you select a

construction sites location (region) in the Terrain dialog box. In
this part the mode is totally equivalent to the Snow mode in which a
snow load on single-span buildings is specified.
The Source data tab is used to specify data regarding the design
and roofs of the left and right spans (Fig. 2.4.7-2).
The source data are specified exactly in the same way as those
for single-span buildings.

Fig. 2.4.7-2. The Source data tab

The Snow load tab is similar to its counterpart for single-span

buildings.
The tab presents plots of the design and rated values of the
snow loads on the left and right roofs. When necessary, it shows an
additional load on the right roof caused by a snow bag (Fig. 2.4.7-3).

Fig. 2.4.7-3. The Snow load tab

(the right roof has an extra snow bag load)

Limitations of the implementation

Scheme 8 in Annex 3 to SNiP or Annex Zh to DBN considers
only buildings (item a) and canopies (item b), while lowered roofs
perpendicular to the main building (item c) are out of consideration.

26
 WEST

2.4.8 Temperature
This mode is used to calculate values of temperature-related
climatic actions in compliance with provisions of Section 8 of SNiP
or Section 11 of DBN.
The mode determines a variation with time of the average
temperature of an element, t, comparing to the mounting
temperature of the construction, and a temperature difference, ,
across the elements cross-section.
All data concerning the structures type and design are taken
from drop-down lists; they comply with formulations of Table 15 of
SNiP and Table 11.1 of DBN. Construction site data can be retrieved
from the Terrain mode or specified directly in the modes window.
The temperature of interior air in the room is assumed to be
22C in the warm season of the year and 16C in the cold season.
Fig. 2.4.8-1. The
The default safety factor for load is assumed to be 1,1.
Temperature actions tab

2.4.9 Ice glaze load on cables and ropes

This mode is used to determine an ice load on cables and ropes.

It implements requirements of Paragraph 7.2 of SNiP and
Paragraph 10.5 of DBN in the part related to the calculations of a
linear ice glaze load. The rated (as per SNiP) or characteristic (as per
DBN) value of the ice load is calculated per unit of length of a cable
or rope.
The design (SNiP) or limit (DBN) value of the ice load is
derived by multiplying the rated or characteristic value by the safety
factor for load.
In the SNiP-compliant analysis, the safety factor is set equal to
1,3 by default as defined in Paragraph 7.3 of SNiP.
The safety factor for limit ice glaze load value in the DBN-
Fig. 2.4.9-1. The Source data tab of the Ice based analysis is defined by provisions of Paragraph 10.10.
Glaze (SNiP) mode The user is allowed to change the factor in the edit mode (the
button ).
In addition to the ice load, the mode calculates a wind load
during glaze (a gust-and-glaze load).
In the SNiP-based analysis, it is calculated according to
Paragraph 7.4 of SNiP. Source data regarding the wind zone as per
Map 3 and the glaze zone as per Map 4 of the mandatory annex 5 to
SNiP can be specified directly on the Source data tab (Fig. 2.4.9-1)
or carried over from the Terrain mode using tools common for the
WeST application.
In the DBN-based analysis, the wind load is calculated
according to provisions of Paragraph 10.9. Source data concerning
the wind zone during ice glaze from the map in Fig. 10.2 and those
Fig. 2.4.9-2. The Source data tab of the Ice concerning the ice glaze zone from the map in Fig. 10.4 can be
Glaze (DBN) mode entered directly in the Source data tab (Fig. 2.4.9-2) or retrieved
from the Terrain mode by common WeST techniques. If the current

27
WEST

working code is DBN, the button will provide access to a list of

Ukrainian cities which contains refined data (based on Annex E)
concerning the loads characteristic values. If you select a city and
click the OK button, the characteristic value of the load will be
carried over to the source data set. In addition, the loads can be
revised on the basis of the zone loads defined by provisions of
Annex E.

On the Source data tab, the user can specify a thickness of the
ice glaze and a wind load value different from those set for the
current zone by SNiP and DBN.

The calculated results in the SNiP-based analysis (Fig. 2.4.9-3)

Fig. 2.4.9-3. The Results tab of the Ice
will consist of rated and design values of the ice glaze load, and also
Glaze (SNiP) mode
the wind load on cables (ropes) covered with ice.

The calculated results in the DBN-based analysis (Fig. 2.4.9-4)

will consist of limit design values of the ice glaze load, and the limit
design wind load on cables (ropes) covered with ice.

The wind load during ice glaze is calculated under the

assumption that the cable (rope) is located in the plane perpendicular
to the wind flow. When calculating the wind load, the application
allows for the fact that the diameter of the cable (rope) is bigger than
it was originally because of ice covering it.
Results of the calculation are presented in a graphical form on
the respective tab. There is a capability of getting numbers by
Fig. 2.4.9-4. The Results tab of the Ice scanning the plots.
Glaze (DBN) mode

Limitations of the implementation

The ice load is calculated for cables (ropes) suspended not
higher than one hundred meters above the ground.

28
 WEST

Design codes implemented by WeST

Mode References to clauses in codes and standards
in the analysis for compliance in the analysis for compliance with
with SNiP 2.01.07-85 and DBN V.1.2-2:2006
SNiP 2.01.07-85*
Densities Par. 2.2 Pars. 5.2, 5.3
Terrain Annex 5, SNiP 2.01.01-82 Pars. 8.5, 9.6, 10.7, 10.9, Annex Zh
Factors Pars. 2.2, 3.4 Pars. 5.2, 5.3, 6.8, 6.9, 8.11, 8.12, 9.14,
9.15, 10.10, 10.11, 11.8
Self-weight Par. 2.2, Annex 5 Pars. 5.2, 5.3, Annex 5
SNiP 2.03.13-88 SNiP 2.03.13-88,
DBN V.2.6-14-97
Deflection limits Pars. 10.7, 10.11, 10.12 Pars. 5.1, 6.1, 7.1 DSTU B V.1.2-3:2006
Temporary Pars. 3.53.9 Pars. 6.56.9
Wind Pars. 6.16.7, 6.11, Pars. 9.29.10,
Annex 4 (schemes 1, 2, 3, 9, 11, Annex I (schemes 1, 2, 3, 9, 11, 12b, 14,
12b, 14, 18) 18)
Wind. Pulsation Pars. 6.16.5, 6.76.10
Full wind Pars. 9.49.13
Snow. Single-span Pars. 5.15.7, Annex 3 (schemes 1, Pars. 8.108.12, Annex E (schemes 1, 2, 3,
buildings 2, 3, 10) 10)
Snow. Two-span buildings Pars. 5.15.7, Annex 3 (schemes 4, Pars. 8.108.12, Annex E (schemes 4, 5, 6,
5, 6, 7, 8a) 7, 8a)
Temperature GOST 12.1.005-88, Pars. 11.1-11.8
Pars. 8.18.7, SNiP 2.01.01-82
Ice on cables and ropes Pars. 7.27.4 Pars. 10.2-10.5, 10.7-10.13

Bibliography
1. SNiP 2.01.07-85. Loads and actions. USSR State Comm. for Construct. and Architect.
Moscow, 1986. 36 p.
2. SNiP 2.01.07-85*. Loads and actions. Building rules and regulations / State Comm. for Construct. of
Russia. Moscow, 2001. 44 p.
3. DSTU B V.1.2-3:2006 Deflections and displacements. Ministry of Construction of Ukraine, Kiev,
2006 10 p.
4. DBN V.1.2-2:2006 Loads and actions Ministry of Construction of Ukraine, Kiev, 2006 60 p.

29