Road Liner Thermoplastic

YOUR SAFETY, OUR PRIORITY
TECHNICAL DATA SHEET

DESCRIPTION
Hot applied road marking paint con-
sists of a light colored aggregates,
pigment, extender, and glass beads,
bound together with a thermoplastic
resin, plasticized as necessary. When
in molten state after heating, it is
applied hot to the road surfaces, using
screed, Extrusion, or sprayed applica-
tion. The material is ENVIROMENT
FRIENDLY consisting of 100/o solids,
no solvents & Organic yellow pigment.
FEATURES
Water based
Good coverage
Smooth flat finish
THERMOPLASTIC
ROAD MARKING
REFLECTIVE
AGGREGATE
The aggregate consists of light colored silica sand, calcite, quartz, calcined flint or other
approved aggregate.
TECHNICAL DATA SHEET
APPLICATION GUIDE
SURFACE PREPARATION MATERIAL APPLICATION AFTERCARE

The road surface must be dry and free from dust, Material has to be placed into a pre-heater fitted Under normal traffic conditions with temperature
dirt, mud, grease, salt, and any other contaminate. with mechanical stirrer and thermometer. When within normal range and periodic rainfall, thermo-
The temperature of the road surface must be below the material has been heated to its application plastic road marking material is self-cleaned and
60OC and the 10Oc. Road Marking applied to new temperature, around 20020OC, carefully requires no ongoing maintenance.
or abnormally hot bituminous surface can become
transfer to the application equipment and
disclosed or obliterated by the transfer of bitumi-
proceed with use. Maximum safe heating
nous by vehicle tiers. Material must be applied at
temperature of 220OC should not be exceed- STORAGE & HEALTH
least 710 days newly applied Asphalt surface and
may vary depending on bitumen content in Asphalt ed. Material may be applied by screed, extru-
& Weather Conditions. The material can be laid sion and spray method using either machine or The product must be stored in a dry, cool, well
over existing thermoplastic marking if the original hand screed equipment to the following ventilated space and away from source of heat
marking are sound. If not, old thermoplastic has to thicknesses. and ignition. Containers
be removed before applying new material. must be kept
On badly worn bituminous and concrete, road Screed lines: 1.5 5.0 mm tightly closed
surface must be treated with primer or other Sprayed lines ( Other than Yellow)= 1.5 mm and upright and
approved material prior to application of thermo- Sprayed yellow edge lines = 0.8 mm handle with
plastic. Extruded lines: 1 3.5mm care.
Coverage: 3.5 k/g m2 @ 1.5 mm
ADDITIONAL INFORMATION
Drop on glass beads, confirming to BS 6088
Class B, may be applied to improve road mark- HEALTH, SAFETY AND
TECHNICAL DETAILS ing visibility at a rate of 45050 g/m2. Material ENVIRONMENT NOTES
may be re-heated gradual Material may be
!
Composition: re-heated gradually, toavoid scorching, and Please observe the
The proportions of constitution of the road mark- used after solidifying providing the total time in precautionary notices
ing material are: Binder (Hydrocarbon resin) 202/o molten state has not exceeded 6 hours. displayed on the
by mass Solid glass beads 20/o by mass min.
Aggregate, pigment, extender, & glass beads 802/o
container. Keep out of
Newly applied road marking must be coned, or the reach of
by mass blocked by any other means of traffic safety, and
should not be subject to any traffic for minimum
children. Use under
well ventilated
CAUTION
Pigment of 12 hours to achieve best result.
The white pigment is TITANIUM DIOXIDE (anatase or conditions. Do not
rutile) complying with BS 1851 and its content is such breathe or inhale mist. Avoid skin contact.
that to give a minimum luminance factor of 70/o. Spillage on the skin should immediately be
Sufficiently heat stable ORGANIC PIGMENT is the AVAILABLE PACKS
yellow pigment used. Its content depends on the color removed with suitable cleanser, soap and
required and not required and not to exceed 5o/o by water. Eyes should be well flushed with water
mass. and medical attention sought immediately.
The material is supplied in Wear suitable gloves. A suitable cartridge
Extender powder/granule from packed in mask should be worn when rubbing down.
approximately 25kg plastic sacks.
The extender is calcium carbonate prepared from Do not empty into drain or watercourses and
natural chalk.
dispose of any paint waste in accordance
with the appropriate environment.
Binder Shelf life: years from date of manufacture in original
The binder is plasticized synthetic resin, plasticized tightlyclosed containers away from direct sunlight and
natural resins or rosins. The viscosity and wetting excessive heat. For detailed information on the health and
properties of the binder at the application temperature safety hazards and precautions for use of this
give a composition that can be applied satisfactory. product, we refer to the Material Safety Data
Sheet.
TECHNICAL SUPPORT
Happilac Paints Technical Services Department is available to assist you in the correct use of our products and its resources are at your
disposal entirely without obligation.
For detailed information on the health & safety hazards and precautions for use of this product, we refer to the Material Safety Data Sheet.
Karss Paint Industries (Pvt) Ltd, West Canal Road, Pipon wala Pul, Faisalabad. For Feedback/complaints, write to Marketing Manager Services
Version No. H01/2015. Please note that this datasheet supersedes all previous versions

Road Liner Thermoplastic

Uploaded by

Copyright:

Available Formats

Road Liner Thermoplastic

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Road Liner Thermoplastic

Uploaded by

Copyright:

Available Formats

YOUR SAFETY, OUR PRIORITY

TECHNICAL DATA SHEET

SURFACE PREPARATION MATERIAL APPLICATION AFTERCARE

You might also like