LTM8067

2.8VIN to 40VIN Isolated

Module DC/DC Converter

Features Description
nn 2kVAC Isolated Module Converter The LTM8067 is a 2kVAC isolated flyback Module
nn UL60950 Recognized File 464570 (power module) DC/DC converter. Included in the package
nn Wide Input Voltage Range: 2.8V to 40V are the switching controller, power switches, transformer,
nn Up to 450mA Output Current (V = 24V V
IN , OUT = 5V) and all support components. Operating over an input
Output Adjustable from 2.5V to 24V voltage range of 2.8V to 40V, the LTM8067 supports
nn Current Mode Control an output voltage range of 2.5V to 24V, set by a single
nn User Configurable Undervoltage Lockout resistor. Only output and input capacitors are needed to
nn Low Profile (9mm 11.25mm 4.92mm) finish the design.
BGA Package
The LTM8067 is packaged in a thermally enhanced, com-
pact (9mm 11.25mm 4.92mm) overmolded ball grid
Applications array (BGA) package suitable for automated assembly
nn Isolated IGBT Gate Drive by standard surface mount equipment. The LTM8067 is
nn Industrial Sensors available with SnPb or RoHS compliant terminal finish.
nn Industrial Switches L, LT, LTC, LTM, Linear Technology, the Linear logo and Module are registered trademarks of
Linear Technology Corporation. All other trademarks are the property of their respective owners.
nn Test and Measurement Equipment

Typical Application
2kVAC Isolated Module Regulator Maximum Output Current vs VIN
Max Load Current vs VIN
VIN VIN VOUT VOUT 600
2.8V TO 5V
40V RUN
22F
2.2F VOUTN
LOAD CURRENT (mA)

FB 400

LTM8067
8.25k
GND
8067 TA01a

200

0
0 10 20 30 40
VIN (V)
8067 TA01b

8067fb

For more information www.linear.com/LTM8067 1

LTM8067
Absolute Maximum Ratings Pin Configuration
(Note 1)
TOP VIEW
VIN, RUN, BIAS .........................................................42V
VOUT Relative to VOUTN..............................................25V A
VIN + VOUT (Note 2)....................................................48V B
GND to VOUT Isolation (Note 3).......................... 2kV AC C BANK 2 BANK 1
VOUTN VOUT
Maximum Internal Temperature (Note 4)............... 125C D
Peak Solder Reflow Body Temperature.................. 245C
E
Storage Temperature.............................. 55C to 125C BANK 5
BANK 4
GND
F VIN
RUN
G FB

1 2 3 4 5 6 7
BGA PACKAGE
38-LEAD (11.25mm 9mm 4.92mm)
TJMAX = 125C, JA = 20.8C/W, JCbottom = 5.1C/W, JCtop = 18.4C/W, JB = 5.3C/W
WEIGHT = 1.1g, VALUES DETERMINED PER JEDEC 51-9, 51-12

Order Information http://www.linear.com/product/LTM8067#orderinfo

PART MARKING* PACKAGE MSL

PART NUMBER PAD OR BALL FINISH DEVICE CODE TYPE RATING TEMPERATURE RANGE (SEE NOTE 4)
LTM8067EY#PBF SAC305 (RoHS) LTM8067Y e1 BGA 3 40C to 125C
LTM8067IY#PBF SAC305 (RoHS) LTM8067Y e1 BGA 3 40C to 125C
LTM8067IY SnPb (63/37) LTM8067Y e0 BGA 3 40C to 125C

Consult Marketing for parts specified with wider operating temperature Recommended LGA and BGA PCB Assembly and Manufacturing
ranges. *Device temperature grade is indicated by a label on the shipping Procedures:
container. Pad or ball finish code is per IPC/JEDEC J-STD-609. www.linear.com/umodule/pcbassembly
Terminal Finish Part Marking: LGA and BGA Package and Tray Drawings:
www.linear.com/leadfree www.linear.com/packaging

8067fb

2 For more information www.linear.com/LTM8067

 LTM8067
Electrical
The Characteristics l denotes the specifications which apply over the full internal
operating temperature range, otherwise specifications are at TA = 25C, RUN = 2V (Note 4).
PARAMETER CONDITIONS MIN TYP MAX UNITS
Minimum Input DC Voltage RUN = 2V l 2.8 V
VOUT DC Voltage RADJ = 15.4k 2.5 V
RADJ = 8.25k l 4.75 5 5.25 V
RADJ = 1.78k 24 V
VIN Quiescent Current VRUN = 0V 3 A
Not Switching 7 mA
VOUT Line Regulation 3V VIN 40V, IOUT = 0.1A, RUN = 2V 1 %
VOUT Load Regulation 0.05A IOUT 0.3A, RUN = 2V 1 %
VOUT Ripple (RMS) IOUT = 0.1A, 1MHz BW 30 mV
Isolation Voltage (Note 3) 2 kV
Input Short-Circuit Current VOUT Shorted 80 mA
RUN Pin Input Threshold RUN Pin Falling 1.18 1.214 1.25 V
RUN Pin Current VRUN = 1V 2.5 A
VRUN = 1.3V 0.1 A

Note 1: Stresses beyond those listed under Absolute Maximum Ratings with statistical process controls. LTM8067I is guaranteed to meet
may cause permanent damage to the device. Exposure to any Absolute specifications over the full 40C to 125C internal operating temperature
Maximum Rating condition for extended periods may affect device range. Note that the maximum internal temperature is determined by
reliability and lifetime. specific operating conditions in conjunction with board layout, the rated
Note 2: VIN + VOUT is defined as the sum of (VIN GND) + (VOUT VOUTN). package thermal resistance and other environmental factors.
Note 3: The LTM8067 isolation test voltage of either 2kVAC or its Test flowcharts are posted for viewing at:
equivalent of 2.83kVDC is applied for one second. www.linear.com/quality
Note 4: The LTM8067E is guaranteed to meet performance specifications
from 0C to 125C. Specifications over the 40C to 125C internal
temperature range are assured by design, characterization and correlation

8067fb

For more information www.linear.com/LTM8067 3

 LTM8067
Typical Performance Characteristics Unless otherwise noted, operating conditions are
as in Table 1 (TA = 25C).

Efficiency vs Load Current, Efficiency vs Load Current, Efficiency vs Load Current,

VOUT = 2.5VV
Efficiency, VOUT = 3.3V VOUT = 5V
OUT = 2.5V OUT OUT
80 80 90

70 80
70

EFFICIENCY (%)

EFFICIENCY (%)
EFFICIENCY (%)

60 70
60
50 60

VIN = 5V 50 VIN = 5V VIN = 5V

40 VIN = 12V VIN = 12V 50 VIN = 12V
VIN = 24V VIN = 24V VIN = 24V
VIN = 36V VIN = 36V VIN = 36V
30 40 40
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350 400 0 100 200 300 400 500 600
LOAD CURRENT (mA) LOAD CURRENT (mA) LOAD CURRENT (mA)
8067 G01 8067 G02 8068 G03

Efficiency vs Load Current, Efficiency vs Load Current, Efficiency vs Load Current,

VOUT = 8V OUT VOUT = 12VV OUT = 12V
Efficiency, VOUT = 15V OUT
85 85 85

75 75
75
EFFICIENCY (%)

EFFICIENCY (%)
EFFICIENCY (%)

65 65

65
55 VIN = 5V 55 VIN = 5V
VIN = 12V VIN = 12V VIN = 5V
VIN = 24V VIN = 24V VIN = 12V
VIN = 36V VIN = 36V VIN = 24V
45 45 55
0 100 200 300 400 500 0 50 100 150 200 250 300 0 50 100 150 200 250
LOAD CURRENT (mA) LOAD CURRENT (mA) LOAD CURRENT (mA)
8068 G04 8068 G05 8068 G06

Efficiency vs Load Current, Input Current vs Load Current Input Current vs Load Current
VOUT = 24V OUT VOUT = 2.5V VOUT = 3.3V
85 100 125

100
75
INPUT CURRENT (mA)
INPUT CURRENT (mA)

75
EFFICIENCY (%)

75

50
50
65
25 VIN = 5V VIN = 5V
VIN = 5V 25 VIN = 12V
VIN = 12V
VIN = 12V VIN = 24V VIN = 24V
VIN = 24V VIN = 36V VIN = 36V
55 0 0
0 25 50 75 100 125 0 50 100 150 200 250 300 350 0 100 200 300 400
LOAD CURRENT (mA) LOAD CURRENT (mA) LOAD CURRENT (mA)
8067 G07 8067 G08 8067 G09

8067fb

4 For more information www.linear.com/LTM8067

 LTM8067
Typical
Performance Characteristics Unless otherwise noted, operating conditions are
as in Table 1 (TA = 25C).

Input Current vs Load Current Input Current vs Load Current Input Current vs Load Current
VOUT
OUT = 5V VOUT
OUT
= 8V VOUT = 12V
300 400 400
VIN = 5V VIN = 5V VIN = 5V
VIN = 12V VIN = 12V VIN = 12V
VIN = 24V VIN = 24V VIN = 24V
240
VIN = 36V 300 VIN = 36V VIN = 36V
300
INPUT CURRENT (mA)

INPUT CURRENT (mA)

INPUT CURRENT (mA)

180
200 200
120

100 100
60

0 0 0
0 100 200 300 400 500 600 0 100 200 300 400 500 0 100 200 300
LOAD CURRENT (mA) LOAD CURRENT (mA) LOAD CURRENT (mA)
8067 G10 8087 G11 8067 G12

Input Current vs Load Current Input Current vs Load Current Input Current vs VIN, VOUT
VOUT = 15V VOUT
OUT
= 24V Shorted
Input Current vs VIN, VOUT Shorted
400 400 250
VIN = 5V VIN = 5V
VIN = 12V VIN = 12V
VIN = 24V VIN = 24V 200
300 300
INPUT CURRENT (mA)

INPUT CURRENT (mA)

INPUT CURRENT (mA)

150
200 200
100

100 100
50

0 0 0
0 100 200 300 0 50 100 150 0 10 20 30 40
LOAD CURRENT (mA) LOAD CURRENT (mA) VIN (V)
8067 G13 8067 G14 8067 G15

Maximum
Maximum Load
Load Current
Current vs
vs VVOUT
OUT Maximum Load CurrentINvs VIN Maximum
Max Load Load Current
Current vs VINvs VIN
500 400 600
VIN = 5V 2.5VOUT 5VOUT
VIN = 12V 3.3VOUT 8VOUT
VIN = 24V 12VOUT
MAXIMUM LOAD CURRENT (mA)

MAXIMUM LOAD CURRENT (mA)

MAXIMUM LOAD CURRENT (mA)

375
300 400

250

200 200
125

0 100 0
0 5 10 15 20 25 0 10 20 30 40 0 10 20 30 40
VOUT (V) VIN (V) VIN (V)
8067 G16 8067 G17 8067 G18

8067fb

For more information www.linear.com/LTM8067 5

 LTM8067
Typical
Performance Characteristics Unless otherwise noted, operating conditions are
as in Table 1 (TA = 25C).

Minimum Load Current vs VOUT Output Noise and Ripple

Maximum
Max Load Load Current
Current vs VINvs VIN Over Full Output Voltage Range DC2357A, 200mA Load Current
300 25

MINIMUM LOAD CURRENT (mA)

MAXIMUM LOAD CURRENT (mA)

20
10mV/DIV
200
15

10
C5 = 470pF
100
HP461 150MHz AMPLIFIER AT 40dB GAIN
5 8067 G21
24VOUT 2s/DIV
12VOUT DATA0
0 0
0 10 20 30 40 0 6 12 18 24
VIN (V) VOUT1 (V)
8067 G19 8067 G20

Frequency vs VOUT Load Current

Stock
Stock DC2357A
DC2357A Demo
Demo Board
Board Derating, 2.5VOUT
OUT Derating, 3.3V
Derating, 3.3VOUT
OUT
450 400 400
0 LFM AIR FLOW 0 LFM AIR FLOW
MAXIMUM LOAD CURRENT (mA)

MAXIMUM LOAD CURRENT (mA)

SWITCHING FREQUENCY (kHz)

300 300
350

200 200

250
100 VIN = 5V 100 VIN = 5V
5VIN VIN = 12V VIN = 12V
12VIN VIN = 24V VIN = 24V
24VIN VIN = 36V VIN = 36V
150 0 0
0 100 200 300 400 500 25 50 75 100 125 25 50 75 100 125
LOAD CURRENT (mA) AMBIENT TEMPERATURE (C) AMBIENT TEMPERATURE (C)
8068 G22 8067 G23 8067 G24

8067fb

6 For more information www.linear.com/LTM8067

 LTM8067
Typical
Performance Characteristics Unless otherwise noted, operating conditions are
as in Table 1 (TA = 25C).

Derating, 5V
Derating, 5VOUT
OUT Derating, 8VOUT OUT Derating, 12VOUT
Derating, 12VOUT
600 450 300
0 LFM AIR FLOW 0 LFM AIR FLOW 0 LFM AIR FLOW

MAXIMUM LOAD CURRENT (mA)

MAXIMUM LOAD CURRENT (mA)

MAXIMUM LOAD CURRENT (mA)

450 225
300

300 150

150
150 VIN = 5V VIN = 5V 75
VIN = 12V VIN = 12V VIN = 5V
VIN = 24V VIN = 24V VIN = 12V
VIN = 36V VIN = 36V VIN = 24V, 36V
0 0 0
25 50 75 100 125 25 50 75 100 125 25 50 75 100 125
AMBIENT TEMPERATURE (C) AMBIENT TEMPERATURE (C) AMBIENT TEMPERATURE (C)
8067 G25 8067 G26 8067 G27

Derating, 15VOUT Derating, 24VOUT

OUT
300 150
0 LFM AIR FLOW 0 LFM AIR FLOW
MAXIMUM LOAD CURRENT (mA)

MAXIMUM LOAD CURRENT (mA)

120
225

90
150
60

75 VIN = 5V
VIN = 12V 30
VIN = 24V VIN = 5V
VIN = 36V VIN = 12V, 24V, 36V
0 0
25 50 75 100 125 25 50 75 100 125
AMBIENT TEMPERATURE (C) AMBIENT TEMPERATURE (C)
8067 G28 8067 G29

8067fb

For more information www.linear.com/LTM8067 7

LTM8067
Pin Functions
PACKAGE ROW AND COLUMN LABELING MAY VARY RUN (Pin F3): A resistive divider connected to VIN and this
AMONG Module PRODUCTS. REVIEW EACH PACKAGE pin programs the minimum voltage at which the LTM8067
LAYOUT CAREFULLY.
will operate. Below 1.214V, the LTM8067 does not deliver
VOUT (Bank 1): VOUT and VOUTN comprise the isolated power to the secondary. When RUN is less than 1.214V, the
output of the LTM8067 flyback stage. Apply an external pin draws 2.5A, allowing for a programmable hysteresis.
capacitor between VOUT and VOUTN. Do not allow VOUTN Do not allow a negative voltage (relative to GND) on this
to exceed VOUT. pin. Tie this pin to VIN if it is not used.
VOUTN (Bank 2): VOUTN is the return for VOUT. VOUT and FB (Pins G7): Apply a resistor from this pin to GND to
VOUTN comprise the isolated output of the LTM8067. In set the output voltage VOUTN relative to VOUTN, using the
most applications, the bulk of the heat flow out of the recommended value given in Table 1. If Table 1 does not
LTM8067 is through the GND and VOUTN pads, so the list the desired VOUT value, the equation:
printed circuit design has a large impact on the thermal
performance of the part. See the PCB Layout and Thermal
( )
RFB = 37.415 VOUT 0.955 k
Considerations sections for more details. Apply an external
capacitor between VOUT and VOUTN. may be used to approximate the value. To the seasoned
designer, this exponential equation may seem unusual. The
GND (Bank 4): This is the primary side local ground of the equation is exponential due to nonlinear current sources
LTM8067 primary. In most applications, the bulk of the heat that are used to temperature compensate the regulation.
flow out of the LTM8067 is through the GND and VOUTN Do not drive this pin with an external power source.
pads, so the printed circuit design has a large impact on
the thermal performance of the part. See the PCB Layout
and Thermal Considerations sections for more details.
VIN (Bank 5): VIN supplies current to the LTM8067s
internal regulator and to the integrated power switch.
These pins must be locally bypassed with an external,
low ESR capacitor.

8067fb

8 For more information www.linear.com/LTM8067

 LTM8067
Block Diagram

VIN VOUT

0.1F 1F

RUN
VOUTN
CURRENT
MODE
CONTROLLER

FB

GND
8067 BD

8067fb

For more information www.linear.com/LTM8067 9

LTM8067
Operation
The LTM8067 is a stand-alone isolated flyback switching The LTM8067 has a galvanic primary to secondary isolation
DC/DC power supply that can deliver up to 450mA of rating of 2kV AC. For details please refer to the Isolation,
output current at 5VOUT, 24VIN. This module provides a Working Voltage and Safely Compliance section. The
regulated output voltage programmable via one external LTM8067 is a UL 60950 recognized component.
resistor from 2.5V to 24V. The input voltage range of the
The RUN pin is used to turn on or off the LTM8067, dis-
LTM8067 is 2.8V to 40V. Given that the LTM8067 is a fly- connecting the output and reducing the input current to
back converter, the output current depends upon the input 1A or less.
and output voltages, so make sure that the input voltage
is high enough to support the desired output voltage and The LTM8067 is a variable frequency device. For a given
load current. The Typical Performance Characteristics input and output voltage, the frequency decreases as the
section gives several graphs of the maximum load versus load increases. For light loads, the current through the
VIN for several output voltages. internal transformer may be discontinuous.
A simplified block diagram is given. The LTM8067 contains
a current mode controller, power switching element, power
transformer, power Schottky diode and a modest amount
of input and output capacitance.

8067fb

10 For more information www.linear.com/LTM8067

 LTM8067
Applications Information
For most applications, the design process is straight acceptable, and can yield improved dynamic response, if
forward, summarized as follows: it is necessary. Again, it is incumbent upon the user to
1. Look at Table 1 and find the row that has the desired verify proper operation over the intended systems line,
input range and output voltage. load and environmental conditions.

2. Apply the recommended CIN, COUT and RFB. Ceramic capacitors are small, robust and have very low
ESR. However, not all ceramic capacitors are suitable.
While these component combinations have been tested for X5R and X7R types are stable over temperature and ap-
proper operation, it is incumbent upon the user to verify plied voltage and give dependable service. Other types,
proper operation over the intended systems line, load and including Y5V and Z5U have very large temperature and
environmental conditions. Bear in mind that the maximum voltage coefficients of capacitance. In an application cir-
output current may be limited by junction temperature, cuit they may have only a small fraction of their nominal
the relationship between the input and output voltage capacitance resulting in much higher output voltage ripple
magnitude and polarity and other factors. Please refer than expected.
to the graphs in the Typical Performance Characteristics
A final precaution regarding ceramic capacitors concerns
section for guidance.
the maximum input voltage rating of the LTM8067. A
Capacitor Selection Considerations ceramic input capacitor combined with trace or cable
inductance forms a high-Q (underdamped) tank circuit. If
The CIN and COUT capacitor values in Table 1 are the the LTM8067 circuit is plugged into a live supply, the input
minimum recommended values for the associated oper- voltage can ring to much higher than its nominal value,
ating conditions. Applying capacitor values below those possibly exceeding the devices rating. This situation is
indicated in Table 1 is not recommended, and may result easily avoided; see the Hot-Plugging Safely section.
in undesirable operation. Using larger values is generally

Table 1. Recommended Component Values for Specific VOUT Values

VIN VOUT CIN COUT RFB
2.8V to 40V 2.5V 2.2F, 50V, 1206 100F, 6.3V, 1210 15.4k
2.8V to 40V 3.3V 2.2F, 50V, 1206 47F, 6.3V, 1210 11.8k
2.8V to 40V 5V 2.2F, 50V, 1206 22F, 16V, 1210 8.25k
2.8V to 37V 8V 2.2F, 50V, 1206 22F, 16V, 1210 5.23k
2.8V to 33V 12V 4.7F, 50V, 1206 10F, 50V, 1210 3.48k
2.8V to 30V 15V 4.7F, 50V, 1206 4.7F, 25V, 1210 2.8k
2.8V to 27V 18V 4.7F, 50V, 1206 4.7F, 25V, 1210 2.37k
2.8V to 21V 24V 4.7F, 50V, 1206 4.7F, 25V, 1210 1.78k
Note: An input bulk capacitor is required.

8067fb

For more information www.linear.com/LTM8067 11

LTM8067
Applications Information
Isolation, Working Voltage and Safety Compliance LTM8067 may be operated with up to 250V working
The LTM8067 isolation is 100% hi-pot tested by tying voltage in a pollution degree 2 environment. The actual
all of the primary pins together, all of the secondary pins working voltage, insulation category, pollution degree and
together and subjecting the two resultant circuits to a other critical parameters for the specific end application
high voltage differential for one second. This establishes depend upon the actual environmental, application and
the isolation voltage rating of the LTM8067 component. safety compliance requirements. It is therefore up to the
user to perform a safety and compliance review to ensure
The isolation rating of the LTM8067 is not the same as that the LTM8067 is suitable for the intended application.
the working or operational voltage that the application
will experience. This is subject to the applications power Safety Rated Capacitors
source, operating conditions, the industry where the end
Some applications require safety rated capacitors, which
product is used and other factors that dictate design re-
are high voltage capacitors that are specifically designed
quirements such as the gap between copper planes, traces
and rated for AC operation and high voltage surges. These
and component pins on the printed circuit board, as well
capacitors are often certified to safety standards such as UL
as the type of connector that may be used. To maximize
60950, IEC 60950 and others. In the case of the LTM8067,
the allowable working voltage, the LTM8067 has two
a common application of a safety rated capacitor would
columns of solder balls removed to facilitate the printed
be to connect it from GND to VOUTN. To provide maximum
circuit board design. The ball to ball pitch is 1.27mm, and flexibility, the LTM8067 does not include any components
the typical ball diameter is 0.75mm. Accounting for the between GND and VOUTN. Any safety capacitors must be
missing columns and the ball diameter, the printed circuit added externally.
board may be designed for a metal-to-metal separation of
up to 3.06mm. This may have to be reduced somewhat to The specific capacitor and circuit configuration for any
allow for tolerances in solder mask or other printed circuit application depends upon the safety requirements of
board design rules. For those situations where informa- the system into which the LTM8067 is being designed.
tion about the spacing of LTM8067 internal circuitry is Table 2 provides a list of possible capacitors and their
required, the minimum metal to metal separation of the manufacturers. The application of a capacitor from GND
primary and secondary is 1mm. to VOUTN may also reduce the high frequency output noise
on the output.
To reiterate, the manufacturers isolation voltage rating
and the required working or operational voltage are of- Table 2. Safety Rated Capacitors
ten different numbers. In the case of the LTM8067, the MANUFACTURER PART NUMBER DESCRIPTION
isolation voltage rating is established by 100% hi-pot Murata GA343DR7GD472KW01L 4700pF, 250V AC,X7R,
testing. The working or operational voltage is a function Electronics 4.5mm 3.2mm
Capacitor
of the end product and its system level specifications. The
Johanson 302R29W471KV3E-****-SC 470pF, 250V AC,X7R,
actual required operational voltage is often smaller than Dielectrics 4.5mm 2mm
the manufacturers isolation rating. Capacitor
Syfer Technology 1808JA250102JCTSP 100pF, 250V AC, C0G,
The LTM8067 is a UL recognized component under 1808 Capacitor
UL 60950, file number 464570. The UL 60950 insula-
tion category of the LTM8067 transformer is Functional.
Considering UL 60950 Table 2N and the gap distances
stated above, 3.06mm external and 1mm internal, the

8067fb

12 For more information www.linear.com/LTM8067

 LTM8067
Applications Information
PCB Layout 4. Place the CIN and COUT capacitors such that their
ground current flow directly adjacent to or underneath
Most of the headaches associated with PCB layout have
the LTM8067.
been alleviated or even eliminated by the high level of
integration of the LTM8067. The LTM8067 is neverthe- 5. Connect all of the GND connections to as large a copper
less a switching power supply, and care must be taken to pour or plane area as possible on the top layer. Avoid
minimize electrical noise to ensure proper operation. Even breaking the ground connection between the external
with the high level of integration, you may fail to achieve components and the LTM8067.
specified operation with a haphazard or poor layout. See
6. Use vias to connect the GND copper area to the boards
Figure 1 for a suggested layout. Ensure that the grounding
internal ground planes. Liberally distribute these GND
and heat sinking are acceptable.
vias to provide both a good ground connection and
A few rules to keep in mind are: thermal path to the internal planes of the printed circuit
1. Place the RFB resistor as close as possible to its respec- board. Pay attention to the location and density of the
tive pin. thermal vias in Figure 1. The LTM8067 can benefit from
the heat sinking afforded by vias that connect to internal
2. Place the CIN capacitor as close as possible to the VIN GND planes at these locations, due to their proximity
and GND connections of the LTM8067. to internal power handling components. The optimum
3. Place the COUT capacitor as close as possible to VOUT number of thermal vias depends upon the printed
and VOUTN circuit board design. For example, a board might use
very small via holes. It should employ more thermal
vias than a board that uses larger holes.

FB
VOUT
LTM8067

COUT1

VOUTN

RUN

CIN VIN

THERMAL/INTERCONNECT VIAS
8067 F01

Figure 1. Layout Showing Suggested External Components, Planes and Thermal Vias

8067fb

For more information www.linear.com/LTM8067 13

LTM8067
Applications Information
Hot-Plugging Safely JA: Thermal resistance from junction to ambient
The small size, robustness and low impedance of ceramic JCbottom: Thermal resistance from junction to the bot-
capacitors make them an attractive option for the input tom of the product case
bypass capacitor of the LTM8067. However, these capaci- JCtop: Thermal resistance from junction to top of the
tors can cause problems if the LTM8067 is plugged into a product case
live supply (see Linear Technology Application Note 88 for
a complete discussion). The low loss ceramic capacitor JCboard: Thermal resistance from junction to the printed
combined with stray inductance in series with the power circuit board.
source forms an underdamped tank circuit, and the volt- While the meaning of each of these coefficients may seem
age at the VIN pin of the LTM8067 can ring to more than to be intuitive, JEDEC has defined each to avoid confu-
twice the nominal input voltage, possibly exceeding the sion and inconsistency. These definitions are given in
LTM8067s rating and damaging the part. If the input JESD 51-12, and are quoted or paraphrased as follows:
supply is poorly controlled or the user will be plugging
the LTM8067 into an energized supply, the input network JA is the natural convection junction-to-ambient air
should be designed to prevent this overshoot. This can be thermal resistance measured in a one cubic foot sealed
accomplished by installing a small resistor in series to VIN, enclosure. This environment is sometimes referred to
but the most popular method of controlling input voltage as still air although natural convection causes the air to
overshoot is adding an electrolytic bulk capacitor to the move. This value is determined with the part mounted to a
VIN net. This capacitors relatively high equivalent series JESD 51-9 defined test board, which does not reflect an
resistance damps the circuit and eliminates the voltage actual application or viable operating condition.
overshoot. The extra capacitor improves low frequency JCbottom is the junction-to-board thermal resistance with
ripple filtering and can slightly improve the efficiency of the all of the component power dissipation flowing through the
circuit, though it can be a large component in the circuit. bottom of the package. In the typical Module converter,
the bulk of the heat flows out the bottom of the package,
Thermal Considerations but there is always heat flow out into the ambient envi-
The LTM8067 output current may need to be derated if it ronment. As a result, this thermal resistance value may
is required to operate in a high ambient temperature. The be useful for comparing packages but the test conditions
amount of current derating is dependent upon the input dont generally match the users application.
voltage, output power and ambient temperature. The JCtop is determined with nearly all of the component power
temperature rise curves given in the Typical Performance dissipation flowing through the top of the package. As the
Characteristics section can be used as a guide. These curves electrical connections of the typical Module converter are
were generated by the LTM8067 mounted to a 58cm2 on the bottom of the package, it is rare for an application
4-layer FR4 printed circuit board. Boards of other sizes to operate such that most of the heat flows from the junc-
and layer count can exhibit different thermal behavior, so tion to the top of the part. As in the case of JCbottom, this
it is incumbent upon the user to verify proper operation value may be useful for comparing packages but the test
over the intended systems line, load and environmental conditions dont generally match the users application.
operating conditions.
JCboard is the junction-to-board thermal resistance where
For increased accuracy and fidelity to the actual application, almost all of the heat flows through the bottom of the
many designers use FEA to predict thermal performance. Module converter and into the board, and is really the
To that end, the Pin Configuration section of the data sheet sum of the JCbottom and the thermal resistance of the
typically gives four thermal coefficients:

8067fb

14 For more information www.linear.com/LTM8067

 LTM8067
Applications Information
bottom of the part through the solder joints and through a A graphical representation of these thermal resistances
portion of the board. The board temperature is measured is given in Figure 2.
a specified distance from the package, using a two-sided, The blue resistances are contained within the Module
two-layer board. This board is described in JESD 51-9. converter, and the green are outside.
Given these definitions, it should now be apparent that none The die temperature of the LTM8067 must be lower than
of these thermal coefficients reflects an actual physical the maximum rating of 125C, so care should be taken in
operating condition of a Module converter. Thus, none the layout of the circuit to ensure good heat sinking of the
of them can be individually used to accurately predict the LTM8067. The bulk of the heat flow out of the LTM8067
thermal performance of the product. Likewise, it would is through the bottom of the module and the BGA pads
be inappropriate to attempt to use any one coefficient to into the printed circuit board. Consequently a poor printed
correlate to the junction temperature vs load graphs given circuit board design can cause excessive heating, result-
in the products data sheet. The only appropriate way to ing in impaired performance or reliability. Please refer to
use the coefficients is when running a detailed thermal the PCB Layout section for printed circuit board design
analysis, such as FEA, which considers all of the thermal suggestions.
resistances simultaneously.

JUNCTION-TO-AMBIENT RESISTANCE (JESD 51-9 DEFINED BOARD)

JUNCTION-TO-CASE (TOP) CASE (TOP)-TO-AMBIENT

RESISTANCE RESISTANCE

JUNCTION-TO-BOARD RESISTANCE
JUNCTION AMBIENT

JUNCTION-TO-CASE CASE (BOTTOM)-TO-BOARD BOARD-TO-AMBIENT

(BOTTOM) RESISTANCE RESISTANCE RESISTANCE

8067 F02

MODULE DEVICE

Figure 2. Approximate Thermal Model of LTM8067

8067fb

For more information www.linear.com/LTM8067 15

LTM8067
Applications Information
12V Flyback Converter Maximum Load Current vs VIN
OUT
300
VIN VIN VOUT VOUT
12V 12V
RUN
10F

MAXIMUM LOAD CURRENT (mA)

4.7F VOUTN
200
FB

LTM8067
3.48k
GND
8067 TA03a 100

0
0 10 20 30 40
VIN (V)
8067 TA03b

15V Inverting Regulator Maximum Load Current vs VIN

OUT
300
VIN VIN VOUT
5V TO 31V
RUN
4.7F MAXIMUM LOAD CURRENT (mA)
4.7F VOUTN VOUT
15V 200
FB

LTM8067
2.8k
GND
8067 TA04a
100

0
0 10 20 30 40
VIN (V)
8067 TA04b

8067fb

16 For more information www.linear.com/LTM8067

 LTM8067
Package Description
Pin Assignment Table
(Arranged by Pin Number)
PIN FUNCTION PIN FUNCTION PIN FUNCTION PIN FUNCTION PIN FUNCTION PIN FUNCTION PIN FUNCTION PIN FUNCTION
A1 VOUTN B1 VOUTN C1 - D1 - E1 GND F1 - G1 VIN H1 VIN
A2 VOUTN B2 VOUTN C2 - D2 - E2 GND F2 - G2 VIN H2 VIN
A3 VOUTN B3 VOUTN C3 - D3 - E3 GND F3 RUN G3 - H3 -
A4 VOUTN B4 VOUTN C4 - D4 - E4 GND F4 GND G4 GND H4 GND
A5 VOUTN B5 VOUTN C5 - D5 - E5 GND F5 GND G5 GND H5 GND
A6 VOUT B6 VOUT C6 - D6 - E6 GND F6 GND G6 GND H6 GND
A7 VOUT B7 VOUT C7 - D7 - E7 GND F7 GND G7 FB H7 GND

Package Photo

8067fb

For more information www.linear.com/LTM8067 17

 BGA Package
38-Lead (11.25mm 9.00mm 4.92mm)

18
(Reference LTC DWG # 05-08-1925 Rev A)
Z SEE NOTES
A DETAIL A
aaa Z 7
E Y G
X A2 SEE NOTES
PIN 1
LTM8067

3
A1
A
ccc Z
PIN A1 b B
CORNER
4 C

D
MOLD b1
D F
CAP
E
SUBSTRATE
F
0.27 0.37 e
Package Description

3.95 4.05
G

DETAIL B H

// bbb Z
aaa Z
7 6 5 4 3 2 1
PACKAGE TOP VIEW
b (38 PLACES) PACKAGE BOTTOM VIEW
DETAIL B
ddd M Z X Y
PACKAGE SIDE VIEW
eee M Z NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994
2. ALL DIMENSIONS ARE IN MILLIMETERS

0.000
3 BALL DESIGNATION PER JESD MS-028 AND JEP95

3.810
2.540
1.270
0.3175
0.3175
1.270
2.540
3.810
4 DETAILS OF PIN #1 IDENTIFIER ARE OPTIONAL,
4.445
BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
DETAIL A THE PIN #1 IDENTIFIER MAY BE EITHER A MOLD OR
3.175 MARKED FEATURE
5. PRIMARY DATUM -Z- IS SEATING PLANE

For more information www.linear.com/LTM8067

1.905 DIMENSIONS
6. SOLDER BALL COMPOSITION IS 96.5% Sn/3.0% Ag/0.5% Cu
0.635 SYMBOL MIN NOM MAX NOTES
0.000 A 4.72 4.92 5.12 7 PACKAGE ROW AND COLUMN LABELING MAY VARY
0.635 ! AMONG Module PRODUCTS. REVIEW EACH PACKAGE
A1 0.50 0.60 0.70
LAYOUT CAREFULLY
1.905 A2 4.22 4.32 4.42
b 0.60 0.75 0.90
3.175
b1 0.60 0.63 0.66
4.1275
Please refer to http://www.linear.com/product/LTM8067#packaging for the most recent package drawings.

4.445 D 11.25
4.7625
E 9.0
SUGGESTED PCB LAYOUT e 1.27
TOP VIEW F 8.89 LTMXXXXXX
G 7.62 Module
aaa 0.15 COMPONENT
PIN A1
bbb 0.10
ccc 0.20
ddd 0.30 TRAY PIN 1
BEVEL
eee 0.15 PACKAGE IN TRAY LOADING ORIENTATION
TOTAL NUMBER OF BALLS: 38 BGA 38 1212 REV A

8067fb
 LTM8067
Revision History
REV DATE DESCRIPTION PAGE NUMBER
A 05/16 Corrected symbol of internal switch in block diagram from NPN transistor to N-channel MOSFET 9
B 11/16 Corrected VOUT on Maximum Load Current vs VIN from 12VOUT to 24VOUT and from 15VOUT to 12VOUT 6
Corrected minimum metal to metal space from 0.75mm to 1mm 12
Updated the Related Parts Table 20

8067fb

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.

However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
For more
tion that the interconnection of itsinformation www.linear.com/LTM8067
circuits as described herein will not infringe on existing patent rights. 19
LTM8067
Typical Application
15V Floating 1GBT Gate Drive
100VDC
15V MOTOR POWER
VIN VIN VOUT 200mA
12V
RUN
4.7F
4.7F
VOUTN
FB

LTM8067
2.8k
GND
8067 TA02a

Design Resources
SUBJECT DESCRIPTION
Module Design and Manufacturing Resources Design: Manufacturing:
Selector Guides Quick Start Guide
Demo Boards and Gerber Files PCB Design, Assembly and Manufacturing Guidelines
Free Simulation Tools Package and Board Level Reliability
Module Regulator Products Search 1. Sort table of products by parameters and download the result as a spread sheet.
2. Search using the Quick Power Search parametric table.

TechClip Videos Quick videos detailing how to bench test electrical and thermal performance of Module products.
Digital Power System Management Linear Technologys family of digital power supply management ICs are highly integrated solutions that
offer essential functions, including power supply monitoring, supervision, margining and sequencing,
and feature EEPROM for storing user configurations and fault logging.

Related Parts
PART NUMBER DESCRIPTION COMMENTS
LTM8068 2kVAC Isolated Module Converter with LDO Post Regulator 2.8V VIN 40V, 1.2V VOUT 18V; 20Vrms Output Ripple.
UL60950 Regognized.
LTM8047 725VDC, 1.5W Isolated Module Converter 3.1V VIN 32V, 2.5V VOUT 12V
LTM8048 725VDC, 1.5W Isolated Module Converter with LDO Post Regulator 3.1V VIN 32V, 1.2V VOUT 12V; 20Vrms Output Ripple
LTM8045 Inverting or SEPIC Module DC/DC Convertor 2.8V VIN 18V, 2.5V VOUT 15V or -2.5V VOUT 15V, Up
to 700mA
LT8300 Isolated Flyback Convertor with 100VIN, 150V/260mA Power Switch 6V VIN 100V, No Opt-Isolator Required
LT8301 Isolated Flyback Convertor with 65V/1.2A Power Switch 2.7V VIN 42V, No Opt-Isolator Required
LT8302 Isolated Flyback Convertor with 65V/3.6A Power Switch 2.8V VIN 42V, No Opt-Isolator Required
LTM8049 Dual Outputs, SEPIC and/or Inverting Module Regulator 2.6V VIN 20V, 2.5V VOUT 25V,
9mm 15mm 2.42mm BGA

8067fb

20 Linear Technology Corporation LT 1116 REV B PRINTED IN USA

1630 McCarthy Blvd., Milpitas, CA 95035-7417

For more information www.linear.com/LTM8067
(408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTM8067 LINEAR TECHNOLOGY CORPORATION 2016