Machine Safety 0 0

MACHINE SAFETY
Introduction
Unguarded moving parts of machines/equipment and the

sudden or uncontrolled release of their power systems can
result in serious injuries.
Personnel working with machines must be aware of the risks

involved and follow safe work practices.
Causes of accidents while working with machinery
Loose clothing, hair, jewelry being caught in moving parts.
Materials ejected from the machine when it is operational.
Inadvertent starting of the machine.
Slipping and falling into an unguarded nip.
Contact with sharp edges, e.g., cutting blade.
Making adjustments while the machine is operational.
Unauthorized operation of machines.
Lack of preventive maintenance.

Hazards
- Rotating machine parts give rise to nip points. Examples are
Rotating gears
Belt and its pulley
Chain and sprocket
Between grinding wheel and tool rest
Between rotating and fixed parts
- Rotating parts operating alone

Shafts
Couplings
- Reciprocating and sliding motions

Dangerous parts of machinery
Running nips between parts rotating in opposite directions,

for e.g., gear wheels.
Nip
point
Rotating parts operating alone e.g., couplings.

Between rotating and tangentially moving parts e.g., belt

drives.
Wherever there is a rotating part operating close to a fixed

structure there is a danger of trapping or crushing.
Reciprocating and sliding motions.

Machine Guarding
Any machine part which can cause injury, must be guarded.
Machine guards help to eliminate personnel hazards created

by points of operation, ingoing nip points, rotating parts and
flying chips.
Types of guards
Commonly used machine guards are
Fixed guard
Interlocked guard
Adjustable guard
Self adjusting guard
Pull back device
Two-hand control
Types of guards
Fixed guard- is kept in place permanently by fasteners that

can only be released by the use of a tool.
Types of guards
Interlocked guard- shuts off or disengages power to the

machine and prevents it from starting when the guard is
removed/opened.
Adjustable guard- provides a barrier which can be adjusted

to suit the varying sizes of the input stock.
Self adjusting guard-provides a barrier which moves

according to the size of the stock entering the danger area.
Types of guards
Two hand control - concurrent use of both hands is

required to operate the machine, preventing the operator
from reaching the danger area.
Pull back - the device is attached to the wrist of the operator

which pulls the operator's hands away from the point of
operation or other hazardous areas when the machine
operates.
Miscellaneous safeguarding aids
Shields can be used to provide protection from flying

particles, splashing metal working fluids or coolants.
Holding tools can be used to place and remove stock.

Example, reaching into the danger area of a power press.
Holding tools must not be used as a replacement of

machine guards.
Safety precautions while working with machinery
Ensure that the guards are in position and in good working

condition before operating.
Know the location of emergency stop switch.
Do not wear loose clothing or jewelry that can be caught in

the rotating parts.
Confine long hair.

The keys and adjusting wrenches must be removed from

the machine before operating it.
Stop the machine before measuring, cleaning or making

any adjustments.
Do not handle metal turnings by hand as they can cause

injury. Use brush or rake to remove turnings.
Keep hands away from the cutting head and all moving
parts.
Cutting tools and blades must be clean and sharp, so that

they can be used without force.
Avoid awkward operations and hand positions. A sudden

slip could cause the hand to move into the cutting tool or
blade.
Keep work area clean. Floors must be level and have a

non-slip surface.
There must be enough space around the machine to do

the job safely.
The person working with the machine must not be

distracted.
Machines must not be left unattended. Switch off the

machine before leaving.
Rotating parts of machines must not be stopped with

hands after switching off.
Compressed air must not be used to clean machines, as

this can force small particles to fly off and can cause injury.
Personal protective equipment
Safety glasses must always be used while working with

machinery for protection from flying particles.
Safety glasses must be worn by all personnel

entering an area where machines are operated.
Personal protective equipment
Ear protection must be worn for protection from high noise.
Safety shoes must be worn if there is handling of heavy

materials.
Hand gloves must NOT be used while working with

machinery, due to the chances of getting caught in the
nip point.
Safe work practices Drill press
When making deep holes,
clean the hole frequently.
Use a clamp or drill vise to

prevent work from spinning.
The drill bit or cutting tool

must be locked securely in
the chuck.
Remove the chuck key before

starting the drill press.
Lubricate drill bit when drilling

metal.
Safe work practices Drill press
Reduce the drilling pressure when the drill begins to break
through the work piece. This prevents drill from pulling into
the work and breaking.
Do not force the drill with extra pressure.
Do not hold the work by hand.
Do not place hands under the stock being drilled.

Safe work practices- Lathe
Centre the drill work deeply enough to provide support
for the piece while it is turning.
Secure and clamp the piece being worked.

Safe work practices- Lathe
Guard must be provided to the chuck.
Inspect chucks for wear or damage.
Remove chuck wrench immediately after adjusting chuck.

Safe work practices -Grinding machine
Causes of personal injury while working with abrasive wheels

are follows:
Holding the work incorrectly.
Incorrect adjustment or lack of

work rest.
Using the wrong type of wheel

or disk or a poorly maintained
or imbalanced one.
Grinding on the side of the

wheel.
Safe work practices -Grinding machine
Causes of personal injury while working with abrasive wheels

are follows(contd.)
Grinding too high above the center of a wheel.
Incorrect mounting and exceeding speeds recommended

by manufacturer can lead to bursting of wheel.
Using spindle with incorrect diameter.

Safe work practices - Grinding machine
Tool/Work rest
The work rest must be securely clamped and the gap

between the tool rest and wheel must not be more than
3mm.
The work rest height must be on the horizontal center

line of the machine spindle.
The rest must never be adjusted while the wheel is in

motion as the work rest may slip and strike the wheel
and break it, or cause injury to the operator.
Lockout-Tagout
Lockout-tagout or lock and tag is a

system used to ensure that
machines are properly shut off and
not started up again before the
completion of maintenance or
servicing work.
Lockout-Tagout
Hazardous power sources must be isolated before any
repair procedure is started.
Different types of locks are used for locking the machine or

the power source in a manner that no hazardous power
sources can be turned on.
A tag is also attached to the locked device indicating that it

must not be turned on.
THANK YOU

Machine Safety 0 0

Uploaded by

Copyright:

Available Formats

Machine Safety 0 0

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Machine Safety 0 0

Uploaded by

Copyright:

Available Formats

MACHINE SAFETY

Unguarded moving parts of machines/equipment and the

Personnel working with machines must be aware of the risks

Loose clothing, hair, jewelry being caught in moving parts.

Materials ejected from the machine when it is operational.

Inadvertent starting of the machine.

Slipping and falling into an unguarded nip.

Contact with sharp edges, e.g., cutting blade.

Making adjustments while the machine is operational.

Unauthorized operation of machines.

Lack of preventive maintenance.

- Rotating machine parts give rise to nip points. Examples are

- Rotating parts operating alone

- Reciprocating and sliding motions

Running nips between parts rotating in opposite directions,

Rotating parts operating alone e.g., couplings.

Between rotating and tangentially moving parts e.g., belt

Wherever there is a rotating part operating close to a fixed

Reciprocating and sliding motions.

Any machine part which can cause injury, must be guarded.

Machine guards help to eliminate personnel hazards created

Commonly used machine guards are

Fixed guard- is kept in place permanently by fasteners that

Interlocked guard- shuts off or disengages power to the

Adjustable guard- provides a barrier which can be adjusted

Self adjusting guard-provides a barrier which moves

Two hand control - concurrent use of both hands is

Pull back - the device is attached to the wrist of the operator

Shields can be used to provide protection from flying

Holding tools can be used to place and remove stock.

Holding tools must not be used as a replacement of

Ensure that the guards are in position and in good working

Know the location of emergency stop switch.

Do not wear loose clothing or jewelry that can be caught in

Confine long hair.

The keys and adjusting wrenches must be removed from

Stop the machine before measuring, cleaning or making

Do not handle metal turnings by hand as they can cause

Cutting tools and blades must be clean and sharp, so that

Avoid awkward operations and hand positions. A sudden

Keep work area clean. Floors must be level and have a

There must be enough space around the machine to do

The person working with the machine must not be

Machines must not be left unattended. Switch off the

Rotating parts of machines must not be stopped with

Compressed air must not be used to clean machines, as

Safety glasses must always be used while working with

Safety glasses must be worn by all personnel

Ear protection must be worn for protection from high noise.

Safety shoes must be worn if there is handling of heavy

Hand gloves must NOT be used while working with

Use a clamp or drill vise to

The drill bit or cutting tool

Remove the chuck key before

Lubricate drill bit when drilling

Do not force the drill with extra pressure.

Do not hold the work by hand.

Do not place hands under the stock being drilled.

Secure and clamp the piece being worked.