Propane

Propane
Propane is a naturally occurring gas composed of three carbon atoms and eight
hydrogen atoms. It is created along with a variety of other hydrocarbons (such
as crude oil, butane, and gasoline) by the decomposition and reaction of organic
matter over long periods of time. After it is released from oil fields deep within
Earth, propane is separated from other petrochemicals and refined for
commercial use. Propane belongs to a class of materials known as liquefied
petroleum gases (LPGs), which are known for their ability to be converted to
liquid under relatively low pressures. As a liquid, propane is 270 times more
compact than it is as a gas, which allows it to be easily transported and stored as
a liquid until ready for use. Approximately 15 billion gal (57 billion L) of
propane are consumed annually in the United States as a fuel gas. The greatest
consumers are the chemical and manufacturing industries, which use propane
as chemical intermediates and aerosol propellants, followed by residential
homes and commercial establishments, who use propane for heating and in
dryers and portable grills.
The value of petroleum products has long been recognized by the civilized
world, with documented examples of their use stretching back more than 5,000
years. The ancient Mesopotamians used petroleum-derived tar-like compounds
for many applications, including caulking for masonry and bricks and adhesives
for jewelry. About 2,000 years ago Arabian scientists learned one of the basic
tenets of petroleum chemistrythat it can be distilled or separated into different
parts, or fractions, based on their boiling points, and that each fraction has its
own distinctive properties.
The modern era of refining is considered to have begun in 1859, when

petroleum was found in Pennsylvania and the Sennaca Oil Company drilled the
first oil well there. From a depth of 70 ft (21.2 m) the world's first oil well
produced nearly 300 tons (305 metric tons) of oil in its first year, and thus an
entire industry was born. Propane was first recognized as an important
component of petroleum in 1910, when a Pittsburgh motor car owner asked
chemist Dr. Walter Snelling why the gallon of gasoline he had purchased was
half gone by the time he got home. The car owner thought the government
should investigate why consumers were being cheated, because the gasoline was
evaporating at a rapid and expensive rate. Snelling discovered a large part of
liquid gasoline was actually composed of propane, butane, and other
hydrocarbons. Using coils from an old hot water heater and other miscellaneous
pieces of laboratory equipment, Snelling built a still that could separate the
gasoline into its liquid and gaseous components. Since the days of Snelling,
chemists have made tremendous advances in techniques for processing propane
and other LPGs. Today, the manufacture of propane gas is an $8 billion industry
in the United States.
Raw Materials
Because propane has natural origins, it is not "made" of other raw materials;
instead, it is "found" in petroleum chemical mixtures deep within the earth.
These petroleum mixtures are literally rock oil, combinations of various
hydrocarbon-rich fluids
which accumulate in subterranean reservoirs made of porous layers of
sandstone and carbonate rock. Petroleum is derived from various living
organisms buried with sediments of early geological eras. The organisms were
trapped between rock layers without oxygen and could not break down, or
oxidize, completely. Instead, over tens of millions of years, the residual organic
material was converted to propane-rich petroleum via two primary processes,
diagenesis and catagenesis. Diagenesis occurs below 122F (50C) when the
organic "soup" undergoes microbial action (and some chemical reactions) which
result in dehydration, condensation, cyclization, and polymerization.
Catagenesis, on the other hand, occurs under high temperatures of 122-424F
(50-200C) and causes the organic materials to react via thermocatalytic
cracking, decarboxylation, and hydrogen disproportionation. These complex
reactions form petroleum in the sedimentary rocks.
The Manufacturing Process
Propane manufacture involves separation and collection of the gas from its
petroleum sources. Propane and other LPGs are isolated from petrochemical
mixtures in one of two waysby separation from the natural gas phase of
petroleum and by refinement of crude oil.
1. Both processes begin when underground oil fields are tapped by drilling
oil wells. The gas/oil hydrocarbon mixture is piped out of the well and
into a gas trap, which separates the stream into crude oil and "wet" gas,
which contains natural gasoline, liquefied petroleum gases, and natural
gas.
2. Crude oil is heavier and sinks to the bottom of the trap; it is then pumped
into an oil storage tank for later refinement. (Although propane is most
easily isolated from the "wet gas" mixture, it can be produced from crude
oil. Crude oil undergoes a variety of complex chemical processes,
including catalytic cracking, crude distillation, and others. While the
amount of propane produced by refinery processing is small compared to
the amount separated from natural gas, it is still important because
propane produced in this manner is commonly used as a fuel for
refineries or to make LPG or ethylene.)
3. The "wet" gas comes off the top of the trap and is piped to a gasoline
absorption plant, where it is cooled and pumped through an absorption
oil to remove the natural gasoline and liquefied petroleum gases. The
remaining dry gas, about 90% methane, comes off the top of the trap and
is piped to towns and cities for distribution by gas utility companies.
4. The absorbing oil, saturated with hydrocarbons, is piped to a still where
the hydrocarbons are boiled off. This petroleum mixture is known as
"wild gasoline." The clean absorbing oil is then returned to the absorber,
where it repeats the process.
5. The "wild gasoline" is pumped to stabilizer towers, where the natural
liquid gasoline is removed from the bottom and a mixture of liquefied
petroleum gases is drawn off the top.
6. This mixture of LP gases, which is about 10% of total gas mixture, can be
used as a mixture or further separated into its three partsbutane,
isobutane, and propane (about 5% of the total gas mixture).
Quality Control
As described above, propane must be carefully isolated from a complex mixture

of petrochemicals which includes methane, ethane, ethene, propene, isobutane,
isobutene, butadiene, pentane, and pentene, to name a few. If such impurities
are not removed, the propane or propane and butane mixture will not liquefy
properly. Liquefaction at appropriate temperature and pressure is critical for
the gas to be economically useful. The liquefied gas industry has established
standardized specifications that LPG mixtures must conform to in order to be
considered acceptable for use as fuel gas. Standardized test methodologies for
evaluating these specifications are approved and published by the American
Society for Testing and Materials (ASTM). For example, the LPG known as
"commercial propane" must have a maximum vapor pressure of 200 psig at
100F (38C) and can have no more than 0.0017 ounces (0.05 ml) of residual
matter. Furthermore, the allowed amount of volatile residue is strictly limited,
and the gas must meet established guidelines for corrosivity to copper, volatile
sulfur content, and moisture. Other mixtures of propane and butane are
commercially available which have slightly different target values.
These tightly held quality standards make propane an environmentally
attractive fuel. In fact, to meet pipeline standards, nearly all pollutants are
removed from propane before it is allowed to enter pipelines. When used in
properly adjusted and maintained burners, propane's emissions easily meet the
standards for clean air set by the Environmental Protection Agency (EPA). Their
testing has proven that propane is environmentally safer than other
hydrocarbon energy sources, and that properly processed propane can be used
as a motor fuel which is significantly cleaner than gasoline. Studies have shown
that, compared to gasoline, propane engines have as much as 45% less ozone-
forming potential. Results of another recent EPA study show propane reduces
total hydrocarbon emissions by 29% according to the new Federal Clean Air
Standards. Furthermore, carbon monoxide emissions are 93% below the
standard, hydrocarbon emissions are 73% below the standard, and nitrogen
oxide emissions are 57% below the standard.
Byproducts/Waste
As detailed above, the manufacture of propane produces a variety of byproducts

that are economically useful. Actually, it is more accurate to think of these not as
byproducts but as co-products, since they are produced along with propane as
part of petroleum refinement. These co-products may be in the form of solids,
gases, or liquids. Solids (or semisolids) include bitumes, hydrogen sulfide, and
carbon dioxide and are sold for fuel purposes. The liquid fractions include crude
oil, which is further refined to give a variety of products. These oils vary
dramatically in appearance and physical properties like boiling point, density,
odor, and viscosity. The different fractions of crude oil are referred to as "light"
or "heavy" depending on their density. Light crude is rich in low-boiling and
paraffinic hydrocarbons; heavy crudes are higher-boiling and more viscous.
They yield a variety of asphalt-like molecules. Many of the co-products of
propane production, such as propylene and butylene, are useful in gasoline
refining, synthetic rubber manufacture, and the production of petrochemicals.
The Future
As the field of petroleum chemistry evolves, propane chemistry will continue to

advance. Improvements will be made in the way propane is separated from
petroleum. One area that offers opportunity for advancement is in the area of oil
well production. Much natural gas is burned at remote oil wells because the
extensive piping system required to transport it is prohibitively expensive. There
are efforts underway to convert more of this wasted gas to condensable gases,
which could be easily stored and transported. It is also important to note that
propane is likely to become increasingly popular as a fuel gas based on
economic factors and enviromnental concerns. In fact, in the Clean Air Act of
1990 Congress named LPGs as one of the clean-burning alternative fuels
designated to take national air quality into the twenty-first century.
Where to Learn More
Books
Clark, William, ed. Handbook of Butane! Propane Gases. Butane-Propane

News, Inc., 1972.
Other
National Propane Gas Association. http://www.propanegas.com/npga/ (July

14,1997).
Randy Schueller
Read more: How propane is made - material, manufacture, used, processing,

parts, components, industry, Raw Materials, The Manufacturing Process,
Quality Control, Byproducts/Waste
http://www.madehow.com/Volume-3/Propane.html#ixzz1BDPSTVwX

Propane

Uploaded by

Copyright:

Available Formats

Propane

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Propane

Uploaded by

Copyright:

Available Formats

Propane

The modern era of refining is considered to have begun in 1859, when

The Manufacturing Process

As described above, propane must be carefully isolated from a complex mixture

As detailed above, the manufacture of propane produces a variety of byproducts

As the field of petroleum chemistry evolves, propane chemistry will continue to

Where to Learn More

Clark, William, ed. Handbook of Butane! Propane Gases. Butane-Propane

National Propane Gas Association. http://www.propanegas.com/npga/ (July

Read more: How propane is made - material, manufacture, used, processing,

You might also like