Introduction to

UNIT 1 INTRODUCTION TO MECHANICAL Mechanical Design

DESIGN
Structure
1.1 Introduction
Objectives

1.2 The Procedure of Design

1.3 The Machine and its Designer
1.4 Mechanical Properties
1.5 Tension Test
1.6 Stress Strain Diagram of Mild Steel
1.7 Compression Strength
1.8 Torsional Shear Strength
1.9 Elastic Constants
1.10 Hardness
1.11 Fatigue
1.12 Creep
1.13 Impact Strength
1.14 Engineering Materials
1.15 Steel
1.16 Alloy Steel
1.17 Stainless Steel
1.18 Cast Iron
1.19 Non-ferrous Materials
1.20 Bearing Materials
1.21 Plastic
1.22 Manufacturing Considerations
1.23 Heat Treatment
1.24 Summary
1.25 Key Words
1.26 Answers to SAQs

1.1 INTRODUCTION
Design is a process that ends in creation of something which will satisfy some need of a
person, group of persons or society. The homes and buildings in which we reside, the
dams which store water for irrigation or generation of electricity, an engine which is
used for pumping water or a hoist for lifting loads are the things that are designed before
they are made. The design does not pertain to a single device, structure or product or
even something which can be seen to exist. The process of design can achieve a system,
which can be identified by its physical entity or by service, which is rendered by the
system. 5
Machine Design The process of design will take into consideration all the factors that are likely to affect
the performance of the end system. The constraints in respect of materials to be used, the
processes for changing shapes and size, the personnel to be employed, the cost of
components and personnel, transportation of final product or establishment of final
system, etc. will be brought under consideration in the design process. If the end result is
the product then its disposal after it has served its purpose is also to be considered during
design.
Mechanical design is one of several design processes, which ends in systems that
provide for doing certain mechanical work or creating certain desired motion and often
both. Such devices will need enough strength or capacity to bear forces, which result
from doing work and creating motion. The possibility of adopting most economic and
convenient process of shaping material to build the device or system will always be the
priority of design. Keeping the cost low at every step to make end product most
economic. Creating such designs will require designer to have some specified knowledge
and experience. In this text we will try to generate requisite knowledge. Some experience
may be gained through solving problems.

Objectives
After studying this unit, you should be able to
explain what is design?
describe the machine and its designer,
illustrate the procedure of design,
know materials used in mechanical design, and
understand the considerations for manufacturing.

1.2 THE PROCEDURE OF DESIGN

The process of design which encompasses design of mechanical systems or machines
consists of a few steps to be followed in order. The discrete steps are :
Recognition
The first step is to recognize the need, i.e. what is the need to be fulfilled. All
designs require that the need should be properly and fully defined and described.
This description may become the statement of the problem.
Synthesis
This step involves identifying all possible solutions and making a list. In case of
mechanical design the step may consist in selecting mechanism or group of
mechanisms which will result in desired motion or group of motions and
transmission of forces.
Analysis
The best solution is chosen based upon knowledge and experience. The chosen
solution is analysed to see the effects of all factors. In case of mechanical design
in which each element is required to transmit some force and has definite motion
will be analysed to determine force to be transmitted and size of element. The
motion will also be analysed.
Material Selection
The analysis will be based upon important information of strength of material,
which will be used to transmit force. The material is selected upon the basis of
strength, and also its ability to undergo process of manufacture.
6
Calculation Introduction to
Mechanical Design
The limits or permissible values of forces or stresses are immediately known if
material is selected. The background knowledge of stress analysis or relationship
between forces and deformations are used to determine the sizes which could be
cross-sectional dimension and length.
Revision and Modification
The availability of material in certain sizes and shapes, and joining of elements for
perfect fit has resulted into standardizations. Such standards are available from
professional institutions, government organisations and manufactures of standard
elements. Therefore, the results of calculations are to be checked against
information from the relevant source or sources. The dimension may be modified
to suit standard.
Report
After a design process has been completed the outcome may be a system which
would satisfy the needs as described in the first step. If the design is mechanical,
the sizes of end connection between the elements would have been decided. The
materials would be known and the type of manufacturing methods would have
been selected. A complete report on the problem has to be prepared. The
mechanical designs are best reported by drawings and standard methods for
specifying material and special manufacturing process on the drawing are well
known practices.

1.3 THE MACHINE AND ITS DESIGNER

A machine is understood to be a device which transmits motion and force in a controlled
manner. A machine is made up of several elements in such a way that each element will
move in coherence with other and force will be transmitted from element to element.
The motion and force at various points will constitute mechanical work or energy.
Hence, the prime function of machine can also be regarded as receiving energy at input
point and transmit it to some other body at output point. Between the input and output
points the form of energy may or may not change. For example, an internal combustion
engine is a machine. It receives thermal energy at the top of piston in the cylinder and
delivers kinetic energy at the crank shaft. A milling machine or a lathe machine receives
mechanical energy and transmits mechanical energy to work piece through removal of
material at cutting point.
In fact, in machine designing we divide activity in the separate steps. One in which only
motion is considered and analyzed without considering forces that may be the cause of
motion. For this step the elements of machines are regarded as rigid or non-deforming.
In the second step the elements are regarded as stationary and forces that are transmitted
from connecting link or created due to motion are considered to be acting on the
element. The element is supposed to be deforming and hence internal resistance called
stress is considered for calculating the size of the element. The subject of Mechanical
Design, Design of Machine Elements, Machine Design or Mechanical Engineering
Design often deals with second step. The first step as included in design procedure at
steps 2 and 3 is often taken separately which is outside the purview of the subject of
Machine Design.
Designing will appear as a decision making process in which the sizes of various
elements will be decided. In simpler designs, enough background information and
knowledge are available by way of which a particular element may be regarded to be
loaded purely axially, as a beam or as a shaft. Some may be under combined loading
when all three or two of these load conditions may exist. A designers capability is tested
by the fact that he creates a similarity between a machine element and any of the
standard loading conditions. For examples treating a gear tooth, as a cantilever beam can
be an example of ingenuity of the designer or regarding belt to be bent like a beam over 7
Machine Design pulley could be another such example. In the present we will be considering several such
examples in which similarity between a machine member and another loaded in a
standard fashion (i.e. axially, bending, torsion or combination thereof) will be brought
out. And then the standard formulae of the subject of Strength of Materials or
Mechanics of Solids may be used. The designer will have to be sensitive to
determination of forces that may arise from any source. For example, a steam turbine is
designed thermodynamically for its major purpose of converting thermal energy into
mechanical energy or design of a hydraulic turbine will use principles of Fluid
Mechanics but a designer of machine will be concerned with the forces that arise from
flow of steam or water upon the elements like blades and rotors. Needless to say that
designer will find it difficult to visualise all the forces comprehensively if he does not
possess comprehensive knowledge of thermodynamics and Fluid Mechanics. We may
end up by collecting various characteristics a designer must possess.
(a) He should have sound and comprehensive knowledge in particular field of
engineering to which the design belongs (like Thermodynamics, Fluid
Mechanics, Refrigeration, etc.)
(b) He invariably should be conversant with Mechanics, Mechanisms,
Structures, Engineering Materials and Manufacturing Processes.
(c) Comprehensive knowledge of Mechanics of Solids for correlating stress,
deformation, forces (loads) and geometry is a must but in certain cases
where the element may not find a parallel in any of standard strength of
Material solution the designer may be required to use advanced techniques
of Theory of elasticity. The expertise in this area is an added feature.
(d) Some situations which are out of the purview of Strength of Material may
require experimental methods like Strain Gauge Survey or Photo-elasticity.
With the advent of fast computers the Numerical Technique of Finite
Elements has become a handy and strong tool in the hands of designer of
machines.
(e) The national and international standards and professional codes make the
job of designing much easier. Many times they are essentially to be
followed under orders of government or by law. Such standards are helpful
in infusing safety of operation and economy. It is thus imperative that a
designer is well versed with standards and codes.
(f) A designer must be able to use his knowledge and experience and must
always be ready to learn from his own experiences and those of others.
Thus, a constant touch with current literature is required.
(g) The ease of operation, safety during operation and convenient repairs and
maintenance along with the cost of equipment are such factors, which are
related to ultimate user. The designer must make himself aware of human
nature and preferences so that his design may be acceptable and remains
safe in all aspects of operation, repair, maintenance and final disposal.
(h) The appearance of the product should be attractive to buyers with whose
needs in mind the design was made. The designer should have
understanding of aesthetics to make the product attractive.

1.4 MECHANICAL PROPERTIES

Properties are quantitative measure of materials behaviour and mechanical properties
pertain to material behaviours under load. The load itself can be static or dynamic. A
gradually applied load is regarded as static. Load applied by a universal testing machine
upon a specimen is closet example of gradually applied load and the results of tension
test from such machines are the basis of defining mechanical properties. The dynamic
load is not a gradually applied load then how is it applied. Let us consider a load P
8
acting at the center of a beam, which is simply supported at its ends. The reader will feel Introduction to
Mechanical Design
happy to find the stress (its maximum value) or deflection or both by using a formula
from Strength of Materials. But remember that when the formula was derived certain
assumptions were made. One of them was that the load P is gradually applied. Such load
means that whole of P doest not act on the beam at a time but applied in instalments. The
instalment may be, say P/100 and thus after the 100th instalment is applied the load P
will be said to be acting on the beam. If the whole of P is placed upon the beam, then it
comes under the category of the dynamic load, often referred to as Suddenly Applied
Load. If the load P falls from a height then it is a shock load. A fatigue load is one
which changes with time. Static and dynamic loads can remain unchanged with time
after first application or may alter with time (increase or reduce) in which case, they are
fatigue load. A load which remains constantly applied over a long time is called creep
load.
All Strength of Material formulae are derived for static loads. Fortunately the stress
caused by a suddenly applied load or shock load can be correlated with the stress caused
by gradually applied load. We will invoke such relationships as and when needed. Like
stress formulae, the mechanical properties are also defined and determined under
gradually applied loads because such determination is easy to control and hence
economic. The properties so determined are influenced by sample geometry and size,
shape and surface condition, testing machines and even operator. So the properties are
likely to vary from one machine to another and from one laboratory to another.
However, the static properties carry much less influence as compared to dynamic
(particularly fatigue) properties. The designer must be fully aware of such influences
because most machines are under dynamic loading and static loading may only be a
dream.
It is imperative at this stage to distinguish between elastic constants and mechanical
properties. The elastic constants are dependent upon type of material and not upon the
sample. However, strain rate (or rate of loading) and temperature may affect elastic
constants. The materials used in machines are basically isotropic (or so assumed) for
which two independent elastic constants exist whereas three constants are often used in
correlating stress and strains. The three constants are Modules of Elasticity (E), Modulus
of Rigidity (G) and Poissons Ratio (v). Any one constant can be expressed in terms of
other two.
An isotropic material will have same value of E and G in all direction but a natural
material like wood may have different values of E and G along fibres and transverse to
fibre. Wood is non-isotropic. Most commonly used materials like iron, steel, copper and
its alloys, aluminum and its alloys are very closely isotropic while wood and plastic are
non-isotropic. The strength of material formulae are derived for isotropic materials only.
The leading mechanical properties used in design are ultimate tensile strength, yield
strength, percent elongation, hardness, impact strength and fatigue strength. Before we
begin to define them, we will find that considering tension test is the most appropriate
beginning.

1.5 TENSION TEST

The tension test is commonest of all tests. It is used to determine many mechanical
properties. A cylindrical machined specimen is rigidly held in two jaws of universal
testing machine. One jaw is part of a fixed cross-head, while other joins to the part of
moving cross-head. The moving cross-heads moves slowly, applying a gradually applied
load upon the specimen.
l
d

9
Figure 1.1 : Tension Test Specimen
Machine Design The specimen is shown in Figure 1.1. The diameter of the specimen bears constant ratio
with the gauge length which is shown is Figure 1.1 as distance between two gauge points
l
marked at the ends of uniform diameter length. In a standard specimen 5 . The
d
diameter, d, and gauge length, l, are measured before the specimen is placed in the
machine. As the axial force increases upon the specimen, its length increases, almost
imperceptibly in the beginning. But if loading continues the length begins to increase
perceptibly and at certain point reduction in diameter becomes visible, followed by great
reduction in diameter in the local region of the length. In this localised region the two
parts of the specimen appear to be separating as the machine continues to operate but the
load upon the specimen begins to reduce. Finally at some lesser load the specimen
breaks, with a sound, into two pieces. However, the increase in length and reduction of
load may not be seen in all the materials. Specimens of some materials show too much of
extension and some show too little. The reader must be conversant with the elastic
deformation, which is recoverable and plastic deformation, which is irrecoverable. Both
type of deformations occur during the test. The appearance of visible decrease in the
diameter in the short portion of length (called necking) occurs when the load on the
specimen is highest. The machines of this type have arrangement (devices) for the
measurement of axial force, P, and increase in length, . The values of force, P and
extensions, can be plotted on a graph. Many machines have x-y recorder attached and
P
direct output of graph is obtained. The stress is denoted by and calculated as where
A
A is the original area of cross-section. Although the area of cross-section of specimen
begins to change as the deformations goes plastic, this reduction is seen at and after the
maximum load. The separation or fracture into two pieces can be seen to have occurred
on smaller diameter. Yet, the stress all through the test, from beginning to end, is
P
represented by . The strain is defined as the ratio of change in length at any load
A

P and original length l and represented by , i.e. at all loads. Since A and l are
l
constants hence nature of graph between P and (load-extension) or between and
(stress-strain) will be same. Figure 1.2 shows a stress-strain diagram, typically for a
material, which has extended much before fracture occurred.

e
b c
d
or
P f

o or

Figure 1.2 : Typical Diagram

At first we simply observe what this diagram shows. In this diagram o is the starting
point and oa is straight line. Along line oa, stress () is directly proportional to strain ().
Point b indicates the elastic limit, which means that if specimen is unloaded from any
point between o and b (both inclusive) the unloading curve will truly retrace the loading
curve. Behaviour of specimen material from point b to c is not elastic. In many materials
all three points of a, b and c may coincide. At c the specimen shows deformation without
any increase in load (or stress). In some materials (notably mild or low carbon steel) the
10 load (or stress) may reduce perceptibly at c, followed by considerable deformation at the
reduced constant stress. This will be shown in following section. However, in most Introduction to
Mechanical Design
materials cd may be a small (or very small) region and then stress starts increasing as if
the material has gained strength. Of course the curve is more inclined toward axis. This
increase in stress from d to e is due to strain hardening. Also note again that ob is elastic
deformation zone and beyond b the deformation is elastic and plastic meaning that it is
part recoverable and part irrecoverable. As the deformation increases plastic deformation
increases while elastic deformation remains constant equal to that at b. If the specimen is
unloaded from any point in the plastic deformation region the unloading curve will be
parallel to elastic deformation curve as shown in Figure 1.3.
e

a,b,c
y g
d f

i j k m
o
p el
% long
100
f

Figure 1.3 : Diagram for a Ductile Material

Percent Elongation
From any point g the unloading will be along gi where gi is parallel to oa. oi is the
strain which remains in the specimen or the specimen is permanently elongated by
l p. The total strain at g when the specimen is loaded is oj p el where el is
recoverable part. At fracture, i.e. at point f, if one is able to control and unload the
specimen just before fracture, the unloading will follow f k. The strain ok is an
important property because deformation is defined as percent elongation. Hence,
ok = % elongation/100. Percent elongation is important property and is often
measured by placing two broken pieces together and measuring the distance
between the gauge points. You can easily see that after the fracture has occurred,
the specimen is no more under load, hence elastic deformation (which is equal to
km) is completely recovered. However, in a so-called ductile material km << om.
If the distance between gauge points measured on two broken halves placed
together is lf, then
lf l
% Elongation 100
l
The gauge length has pronounced effect on % elongation. Since the major amount
of deformation occurs locally, i.e. over very small length smaller gauge length will
l
result in higher % elongation. After 5 the % elongation becomes independent
d
of gauge length. % elongation is an indication of very important property of the
material called ductility. The ductility is defined as the property by virtue of
which a material can be drawn into wires which means length can be increased
and diameter can be reduced without fracture. However, a ductile material
deforms plastically before it fails. The property opposite to ductility is called
brittleness. A brittle material does not show enough plastic deformation. Brittle
materials are weak under tensile stress, though they are stronger than most ductile
materials in compression.
11
Machine Design

f
x

Figure 1.4 : Diagram for a Brittle Material

A typical diagram for a brittle material is shown in Figure 1.4. The definitions like
too much and too small % elongation fail to give numerical indication. Hence
engineers regard all those materials as brittle, which show a % elongation less
than 5%. Others are regarded as ductile. Most steels low in carbon and medium
carbon range are ductile by this definition. Cast iron is a typical brittle material.
Concrete is another example of a brittle material. The failures in engineering
structures and machine elements always take place due to tensile stress and hence
brittle materials are not used for making such elements. Such components like
beds of machines and foundations can be made in cast iron. If tensile stress
carrying members have to be made in C.1 then they have to be made heavy for
making stress very low.
Ultimate Tensile Strength, Yield Strength and Proof Stress
The maximum stress reached in a tension test is defined as ultimate tensile
strength. As shown in Figure 1.3 the highest stress is at point e and ultimate
tensile stress (UTS) is represented by u. Some authors represent it by Su. The
point c marks the beginning while d marks the end of yielding. c is called upper
yield point while d is called the lower yield point. The stress corresponding to
lower yield point is defined as the yield strength. For the purposes of machines,
the part has practically failed if stress reaches yield strength, (Y), for this marks
the beginning of the plastic deformation. Plastic deformation in machine parts is
not permissible. Hence one may be inclined to treat Y as failure criterion. We will
further discuss this later in the unit.
It is unfortunate to note that many practical materials show diagrams which
do not have such well defined yielding as in Figures 1.2 and 1.3. Instead they
show a continuous transition from elastic to plastic deformation. In such cases
yield strength (Y) becomes difficult to determine. For this reason an alternative,
called proof stress, is defined which is a stress corresponding to certain
predefined strain. The proof stress is denoted by p. A diagram for a
material, which shows no distinct yield is shown in Figure 1.5. The proof stress is
determined corresponding to proof strain p which is often called offset. By laying
p on strain axis to obtain a point q on axis and drawing a line parallel to elastic
line to cut the curve at p the proof stress p is defined. Then p is measured
on stress axis. The values of proof strain or offset have been standardized for
different materials by American Society for Testing and Materials (ASTM). For
example, offset for aluminum alloys is 0.2%, same is for steels while it is 0.05%
for cast iron (CI) and 0.35% for brass and bronze.
12
 Introduction to
p p Mechanical Design
p

q
p

Figure 1.5 : Proof Stress (p) Corresponding to Offset p

Toughness and Resilience
Since the force, which pulls the tension test specimen, causes movement of its
point of application, the work is done. This work is stored in the specimen and can
be measured as energy stored in the specimen. It can be measured as area under
the curve between load (P) and elongation (l). In case of curve area under
the curve represents energy per unit volume.
Toughness is regarded as ability of a material to absorb strain energy during
elastic and plastic deformation. The resilience is same capacity within elastic
range. The maximum toughness will apparently be at fracture, which is the area
under entire diagram. This energy is called modulus of toughness. Likewise
the maximum energy absorbed in the specimen within elastic limit is called
modulus of resilience. This is the energy absorbed in the tension specimen when
the deformation has reached point a in Figure 1.2. But since in most materials the
proportional limit, elastic limit (points a and b in Figures 1.2 and 1.3) seem to
coincide with yield stress as shows in Figure 1.3, the modules of resilience is the
area of triangle as shown in Figure 1.6.

x MediumC Steel

Mild Steel

Modulus
of Resilience

Figure 1.6 : Resilience and Toughness for Two Materials

It can be seen that modulus of resilience is greater for medium carbon steel than
for mild steel, whereas modulus of toughness of two materials may be closely
same. Medium carbon steel apparently has higher UTS and YS but smaller percent
elongation with respect to mild steel. High modulus of resilience is preferred for
such machine parts, which are required to store energy. Springs are good
example. Hence, springs are made in high yield strength materials.
SAQ 1
(a) Discuss the procedure of Design.
(b) What characteristics a designer must possess?
(c) Sketch a stress-stain diagram. What properties you can define with the help
of this diagram?
(d) Distinguish between a brittle and ductile material. Why is a brittle material
not favoured for use as machine element?
(e) Define modulus of resilience and modulus of toughness.
13
Machine Design
1.6 STRESS STRAIN DIAGRAM FOR MILD STEEL
Mild steel as steel classification is no more a popular term. It was in earlier days that
group of steel used for structural purposes was called mild steel. Its carbon content is
low and a larger group of steel, named low carbon steel, is now used for the same
purposes. We will read about steel classification later. Mild steel was perhaps developed
first out of all steels and it was manufactured from Bessemer process by blowing out
carbon from iron in a Bessemer converter. It was made from pig iron. The interesting
point to note is that this steel was first studied through diagram and most properties
were studied with respect to this material. The term yield strength (YS) is frequently
used whereas yield behaviour is not detectable in most steel varieties used today. It is
mild steel, which very clearly shows a yield behaviour and upper and lower, yield points.
Figure 1.7 shows a typical diagram for mild steel.
e

a,b,c C

c, d C yielding d
f

Figure 1.7 : Diagram for Mild Steel

The proportional limit, elastic limit and upper yield point almost coincide. d is lower
yield point and deformation from c to d is at almost constant stress level. There is
perceptible drop in stress from c to c. The deformation from c to d is almost 10 times
the deformation upto c. It can be seen effectively if strain is plotted on larger scale, as
shown on right hand side in Figure 1.7, in which the scale has been doubled.
The mechanism of yielding is well understood and it is attributed to line defects,
dislocations.
The UTS normally increases with increasing strain rate and decreases with increasing
temperature. Similar trend is shown by yield strength, particularly in low carbon steel.

1.7 COMPRESSION STRENGTH

Compression test is often performed upon materials. The compression test on ductile
material reveals little as no failure is obtained. Brittle material in compression shows
specific fracture failure, failing along a plane making an angel greater than 45 o with
horizontal plane on which compressive load is applied. The load at which fracture occurs
divided by area of X-section is called compressive strength. For brittle material the
stress-strain curves are similar in tension and compression and for such brittle materials
as CI and concrete modulus of elasticity in compression is slightly higher than that in
tension.

1.8 TORSIONAL SHEAR STRENGTH

Another important test performed on steel and CI is torsion test. In this test one end of
specimen is rigidly held while twisting moment or torque is applied at the other end.
The result of test is plotted as a curve between torque (T) and angle of twist or angular
displacement . The test terminates at fracture. The T curves of a ductile material is
very much similar to load extension or curve of tensile test except that the torque
14
does not reduce after attaining a maximum value but fracture occurs at maximum torque. Introduction to
Mechanical Design
It is because of the fact that there is no reduction in the sectional area of the specimen
during the plastic deformation. The elastic limit in this case can be found as the point
where straight line terminates and strain hardening begins, marked as point b in
Figure 1.8. Mild steel will show a marked yielding while other ductile materials show a
smooth transition from elastic to plastic deformation. The plastic deformation zone in
torsion is much larger than in torsion because the plastic deformation beginning from
outer surface and spreads inside while in tension the stress being uniform over the
X-section the plastic deformation spreads over entire section at the same time.
T

Tmax

Figure 1.8 : Torque-twist Diagram in Torsion

The modulus of rapture or ultimate torsional shear strength is calculated form

3 Tmax d
u
4 J 2
where Tmax is maximum torque, j is polar moment of inertia of the specimen section of
diameter d. From the T diagram the slope of linear region can be found as
proportional to modulus of rigidity, which is ratio of shearing stress to shearing strain.

1.9 ELASTIC CONSTANTS

Within elastic limit the stress is directly proportional to strain. This is the statement of
Hookes law and is true for direct (tensile or compressive) stress and strain as well as for
shearing (including torsional shearing) stress and strain. The ratio of direct stress to
direct strain is defined as modulus of elasticity (E) and the ratio of shearing stress and
shearing strain is defined as modulus of rigidity (G). Both the moduli are called elastic
constants. For isotropic material E and G are related with Poissons ratio
E
G
2 (1 v)
Poissons ratio which is the ratio of transverse to longitudinal strains (only magnitude) in
tensile test specimen is yet another elastic constant. If stress acts in three directions at
a point it is called volumetric stress and produces volumetric strain. The ratio of
volumetric stress to volumetric strain according to Hookes law is a constant, called bulk
modulus and denoted by K. It is important to remember that out of four elastic constants,
for an isotropic material only two are independent and other two are dependent. Thus K
can also be expressed as function of any two constants.
E
K
3 (1 2v)
It may be understood that elastic constants E and G are not determined from tension or
torsion test because the machines for these tests undergo adjustment of clearance and
also some deformation, which is reflected in diagram ordinarily. The constants are
determined from such devices, which show large deformation for comparatively smaller
load. For example, E is determined by measuring deflection of a beam under a central
load and G is determined by measuring deflection of a close-coiled helical spring under 15
Machine Design an axial load. Poissons ratio is normally not measured directly but is calculated from
above equation. The elastic constants remain fairly constant for a class of material and
are independent of specimens.

1.10 HARDNESS
Hardness of a material is its ability to resist indentation or scratching. This property is
the measure of resistance to wear and abrasion. Both scratch and indention methods are
used for determining this property. For engineering purposes indentation method is used.
The load that is used to cause indentation on a flat surface by an indenter is divided by
surface area of indentation to obtain a number that is called hardness number. A ball of
10 mm diameter made in hardened steel is used as an indenter under a load of 30000 N
and kept applied for 30 sec. The area of indentation is
D
(D D d )
2 2

2
with D as diameter of the ball and d as the diameter of impression on flat surface.
Different loads are used for different materials. Brinell hardness number is the ratio of
load P and area of indented surface as given above. Instead of using the area of surface
of indentation to divide the load P to obtain harness number one can use the area of
circular impression on the surface or the projected area or the depth of indentation
directly can be used as an indicator of hardness. The indenting load divided by projected
area of indentation is defined as Meyer hardness number. The depth of the indentation
mode by a conical indenter is called Rockwell hardness number. Rockwell hardness
uses different loads and indentors for having different Rockwell scales. Rockwell C is
commonly used for steels. Rockwell method is generally preferred over Brinell because
it does not require a finished surface, it can be determined on a finished part without
spoiling the surface and it gives the reading of hardness directly. Rockwell method
measures the depth of the indentation and hardness, called Rockwell hardness number is
inversely proportional to the depth of indentation.
It is no wonder that a relationship exists between hardness of a material and its strength
because both are related to bonding forces at atomic level. Because of nature of stress in
a hardness test being complex (triaxial) and effect of friction creeping in due to contact
between the indentor and the specimen such relationship is difficult to establish.
However, empirically the ultimate tensile strength and Rockwell c hardness are related
as
u 33 Rc

It is also interesting to note that techniques, which increase the ultimate tensile strength
of material also increase the hardness. Increase in strength and hardness is associated
with decrease in ductility (%age elongation), increase in yield or proof strength and
consequent increase in modulus of resilience. For this reason hardness is often used in
lieu of elaborate tension test for characterizing a material or checking effectiveness of
any treatment. Hardness is also used for calculating UTS (u) in design.
It may also be mentioned here that while the treatments given to material may alter yield
strength, ultimate tensile strength, hardness and %age elongation, the modulus of
elasticity will remain unchanged. Thats why the constants of material are to be
differentiated from mechanical properties.

1.11 FATIGUE
Fatigue is not the property but the behaviour of material under stress which changes with
time. Most interesting thing about fatigue is that a stress level which is below yield or
elastic limit is safe if applied once, but if same level is applied repeatedly upon a
16
specimen then it will fail. Such a failure under repeated stressing is called fatigue failure Introduction to
Mechanical Design
and has discernible characteristics.
The most important characteristic of fatigue failure is that it is without perceptible
plastic deformation in the region of fracture. Even if the specimen is loaded under axial
tensile stress which reverses and whose magnitude is below yield strength, the fatigue
failure will occur and there will be no necking or elongation in the specimen. The
fracture surface has a characteristic appearance with rings (under magnification) and
rough surface (Figure 1.9).
Smooth region
rings can be seen
under magnification

Rough zone

Figure 1.9 : Characteristic Fatigue Fracture

InN In107

Figure 1.10 : A Typical Fatigue Curve

The number of cycles after which the specimen fails is called the fatigue life at the
applied stress. If stress level is plotted against ln of number of cycles at failure the
characteristic fatigue curve is obtained (Figure 1.10). The curve indicates that at lower
stress level the specimen tends to have longer life or even may not fail. All fatigue tests
are stopped at 107 cycles and a specimen surviving 10 million cycles is regarded survival
or non-failure. The stress level at which specimen survives 10 million cycles is called
fatigue strength or endurance limit (former denoted by e is preferably used). Fatigue
life at given stress level and fatigue strength are two fatigue properties and they are
influenced by several factors such as specimen size, surface finish, stress concentration,
temperature, frequency, etc. A smooth polished specimen at frequency less than
1000 cycles/min. and room temperature will have
e = 0.5 u (steels)
e = 0.4 u (non-ferrous)
The fatigue strength is affected by several variables :
(a) Fine finished surfaces result in high fatigue strength.
(b) Stress concentration reduces fatigue strength but not as much as stress
concentration factor.
(c) All treatments that improve static strength also improves fatigue strength.
(d) Under-stressing is process of stress cycling below fatigue strength. It
improves fatigue strength. Gradually increasing cyclic stress up to fatigue
strength is coaxing.
17
Machine Design (e) Small size specimen (6 to 12 mm dia) have higher fatigue strength than
larger size specimen (> 6, mm dia), but after 100 mm dia, this effect levels
off.
(f) Corrosive atmosphere, high temperature cause reduction in fatigue strength.

1.12 CREEP
Yet another important behaviour of material arises when the material is subjected to a
constant load over a long time. It is found that a body of material subjected to a load
which causes stress less than yield strength, over a long period of time, undergoes a
deformation which increases as time passess. The strain so created may ultimately cause
the failure. The behaviour of material is termed creep and the strain is known as creep
strain. The rate at which strain increases will decide after what time the material will
fail. At higher stress the strain rate will be higher and vice-versa. It may be noted from
the definition given here that the temperature is not a requirement for creep deformation
to occur. Creep occurs at all temperatures. However, the creep rate is accelerated with
increasing temperature and at temperature which is close to half of melting point
temperature on absolute scale, creep becomes an important consideration in design. Thus
theoretically though higher temperature is not an essential condition for creep yet at
higher temperature it is a real problem. The creep rate at constant temperature increases
with increase in stress and at constant stress it increases with increase in temperature.
The characteristic creep curve is plotted between creep strain and time and is
characterised by three stages as shown in Figure 1.11. A designer would prefer to load a
machine part in such a way that only secondary creep having a constant creep rate sets
in. Tertiary creep is characterized by increasing creep rate and fast ends in fracture.
Creep becomes an important consideration in gas turbine blading design because
temperature is high. The higher limit of temperature in gas turbine is limited because of
creep of blading material.

Primary Secondary Tertiary

Steady State

Time

Figure 1.11 : Creep Curve : Three Stages of Creep are Depicted

Sometime a quantity like creep strength is defined as a stress at a given temperature

which will produce minimum creep rate of a certain amount usually 0.0001 %/hour.
Creep rupture strength is a stress at given temperature, which will cause rupture after a
predefined life in number of hours say 1000 or 10,000 hours. Rupture is theoretically a
fracture occurring with X-sec. reduced to zero. Both creep strength and creep rupture
strength are arbitrary and not used in design but for comparing two materials.
A consequence of creep is a phenomenon called stress relaxation, which refers to
decrease of stress at constant strain. Problem of stress relaxation is common in bolts used
to clamp two parts at higher temperature. For example, bolts used to clamp cover on a
pressure vessel, at high temperature may lose stress after some time and thus clamping
18 force gets reduced.
Addition of 1.25% Cr and 0.5% Mo in 0.1% C steel improves creep resistance. Addition Introduction to
Mechanical Design
of Cr in varying proportion along with Mo in steel help improve creep resistance in
general. Nickel base alloys like Inconel (C-0.04, Fe- 7.0, Cr-15.5, Ni-76) have high creep
resistance. Cobalt base super alloys are also used for various purposes against creep.

1.13 IMPACT STRENGTH

Impart is a rapidly applied load. A notched specimen is broken under impact loading in
an impact test. The state of stress at notch is complex, in fact triaxial and impact load
causes a high strain rate. The combination of rapidly applied load and notch makes the
material to behave in a brittle manner and raises the yield strength. Thus the fracture
occurs before yielding. It is often difficult to calculate the stress at notch and hence the
energy absorbed in fracturing the specimen is measured as the material property and is
given a name as impact strength. Such a value cannot be used for designing but it is an
indicator of the fact as to how much tendency the material has to behave as brittle
material. The machine for such a test consists of a swinging hammer, which through a
free fall is allowed to strike a notched specimen in a way to stress notch in tension. The
potential energy of hammer before striking (i.e. in its raised position) can be calculated
and also the potential energy of the hammer after striking and causing the fracture of the
specimen can be calculated from the height reached by hammer at the end of its swing.
The difference of two potential energies minus loss of energy in moving through air is
the energy absorbed by the specimen in fracturing. This energy is the impact strength of
material of specimen.
Two configuration of notched specimen are in common use and they are shown in
Figure 1.12. Charpy test uses the specimen as simply supported beam while Izod test
uses the specimen as cantilever. In both the cases the load is so applied that notch is in
tension. A 10 mm 10 mm cross-section bar supported over a span of 40 mm and
carrying a V-notch of depth equal to 1/3 of the depth of section is a common Charpy test
specimen. To compare results from different sources standardization of specimens is
necessary. An Izod specimen may be rectangular or circular in section.
Impact Load

Notch

(a) Chary test

Impact load

(b) Izod test

Figure 1.12 : Impact Test Configuration

Apart from two worst condition, viz. of impact and notch, which render specimen brittle
a third condition to be explored is temperature. The material tends to become brittle at
low temperature and hence performing impact tests on notched specimens at different
temperature is imperative. The results of such a test are depicted in Figure 1.13 wherein
the impact strengths are plotted as function of temperature. The results apparently centre
on a temperature Tr showing that for T > Tr the impact strength increase fast but for
T < Tr it reduces fast. Such a temperature is called transition temperature as it represents
the transition from ductile to brittle nature as temperature reduces. The operation of a
machine part or structural component near transition temperature on higher side carries
19
Machine Design the risk that if temperature reduces slightly the material may start behaving in a brittle
manner. Impact tests are often useful in establishing transition temperature. The purpose
could be to avoid such a temperature or to select a material whose transition temperature
is higher than the operating temperature. The material most susceptible to this transition
is mild steel and this material is largely used for structures. The non-ferrous material like
alloys of Cu and A1 do not show such transition from ductile to brittle. For evaluating
performance of welded mild steel such tests are often performed because the mild steel
welded structures are often used in ship building. The ships have to operate in warm and
cool climates.

Impact energy

Tr

Temperature
Figure 1.13 : Influence of Temperature on Notched Bar Impact Energy

1.14 ENGINEERING MATERIALS

The materials used for structures, tools, machines and other durable goods are generally
regarded as engineering materials. These materials are variously classified. Organic and
inorganic materials are close to scientific division. Materials of both types are used for
engineering purposes. Organic substances are mostly derived from living organisms and
necessarily contain carbon as one constituent. Animal hides (leather), wood, oil
(petroleum), several chemicals, paints, man made polymers and natural resins are
examples of organic materials. All elements including metals and their alloys, acids not
having carbon as its constituent, ceramic, non living natural materials like sand and rock
are regarded as inorganic materials. Both types are found in gaseous, liquid and solid
states.
Composites are combination of materials in which neither solution nor chemical reaction
occurs but properties improve for engineering purposes purely because of mechanical
interaction between the constituents. All constituents may be organic or inorganic or
both. Reinforced concrete is a common example while reinforced plastics, cemented
carbide tools are also composites. Reduction in weight, coupled with high strength and
stiffness have opened possibilities of development of newer composites.
Because of ductility, malleability, electrical conductivity and strength the metals have
become very common and dependable engineering martial. Though most metals are
elements (like Fe, A1, Cu, Zn) very few are used in practice. Their properties improve by
alloying. The most commonly used alloy is steel which has Fe as most important
constituent and C and Si as alloying elements in very small proportion. Alloys like steel
have become very dependable materials because their properties can be altered by heat
treatment.

20
High temperature application requires the materials to remain sufficiently strong over a Introduction to
Mechanical Design
wide range of temperature. The oxides, borides, nitrides and carbides of several metallic
elements have high wear resistance, high strength at elevated temperatures but have
marked brittleness. Such materials are described as ceramics.
Polymers or plastic have acquired a great deal of popularity for making parts of
complicated shapes but not subjected to high loads. These are organic compounds made
by chemical processes and are used in form of fibres, sheets and in various other shapes.
Most composites are made using plastics. The composites and plastics have good
resistance against corrosion.
Perhaps the most common engineering materials after bricks and concrete are alloys.
Steel is the foremost example. The elemental metals are mixed in liquid state or heated to
liquid state where they may have total or partial solubility and on cooling the solids may
have total or partial solubility. Combination of two or more metals produce alloys in
solid state in most cases they possess properties better than the constituents. Equilibrium
diagrams drawn between temperature (ordinate) and % age composition of one of the
two constituents give great deal of information about alloys. Number of phases at any
temperature and their chemical composition can be found from phase or equilibrium
diagrams.
Pure iron may contain 99.99% iron, which could be produced by very costly electrolytic
process. Though not good for much strength, pure iron is used for research transformer
cores. Commercial iron may 99% pure. While being expensive it is used for special
purposes for high corrosion resistance and electrical conductivity. Wrought iron contains
about 3% slag particles distributed uniformly in iron matrix. The presence of slag is
helpful in increasing resistance against fatigue and corrosion. This material is used for
steam, oil and water pipelines. The alloys of iron containing upto 2% carbon along with
small amounts of S, Si, P and Mn are classified as steel. Cast iron is yet another alloy of
iron containing more than 2% of carbon.

1.15 STEEL
By far the commonest engineering material, after brick and concrete, is steel. Steel is
known for its several favourable properties. It has strength and ductility, good electrical
and thermal conductivity, it is amenable to machining and other manufacturing processes
and it is comparatively easily produced.
A Steel containing C in the range of 0.04 to 1.2% along with Mn (0.3 to 1.04%), Si (upto
0.3%), S (max 0.04%), P (max 0.05%) is classified as plain carbon steel. Another group
is called alloy steel. C steel is further divided into three groups. They are described here.

Low C Steel
Carbon less than 0.27%. It is marked by high ductility, low strength, good
machinability and formability. They are weldable but do not respond to heat
treatment.

Medium C Steel
Carbon varies between 0.27 and 0.57%. This steel is heat treatable and good
strength is achievable after treatment. This steel is stronger and tougher than low
carbon steel and machines well.

High C Steel
They contain more than 0.57% C. The high C steel responds readily to heat
treatment. In heat-treated state they develop very high strength and hardness and
thus become less machinable. They also lose ductility and in the high carbon range
may become very brittle. The higher C content makes these steel difficult to weld. 21
Machine Design Following table describes applications, the properties required for applications and the
steel which can provide such properties.

Table 1.1 : Application of Plain C Steel

Sl. No. Application Properties Steel

1. Nails, rivets, stampings High ductility, low Low C (AISI 1010),

strength 0.08/0.13,0.1 Max, 0.3/0.60

2. Beams, rolled sections High ductility, low Low C (1020),

strength, toughness 0.17/0.20,0.10/0.20,
0.3/0.60

3. Shafts and gears Heat treatable for good Med C (1030), 0.27/0.35,
strength and ductility 0.20/0.35, 0.5/0.80

4. Crank shaft, bolts, Heat treatable for good Med C (1040), 0.36/0.45,
connecting rod, machine strength and ductility 0.20/0.35, 0.60/0.90
component

5. Lock washers, valve Toughness High C (1060) 0.54/0.66,

springs 0.20/0.35, 0.60/0.90

6. Wrenches, dies, anvils High toughness and High C (1070), 0.64/0.76,

hardness 0.20/0.35, 0.60/0.90

7. Chissels, hammers, Retains sharp edges High C (1080)

shears

8. Cutters, tools, taps, Hardness, toughness, High C (1090), tool steel

hacksaw blades, springs heat treatable

* Composition in % of C, Si, Mn (in this order) with Max P-0.04% and Max S-0.05.

1.16 ALLOY STEEL

Plain C steels contain C in the range of 0.04 to 1.2. Additionally they contain
Mn (0.3 to 1.04%), Si (up to 0.3%), S (0.04% Max) P (0.05% Max). Other than C no
element has significant effect on mechanical properties except that Mn may provide
some hardenability. S and P are undesirable elements.
Several advantages in terms of improved mechanical properties and corrosion resistance
are obtained by adding one or several alloying elements like Si, Mn, Ni, Cr, Mo, W, V,
Cu, B, A1, etc. The various advantages of alloy steel are :
(a) Higher hardness, strength and toughness, hardness on surface and over
bigger cross-section.
(b) Better hardenability and retention of hardness at higher temperatures (good
for creep and cutting tools).
(c) Higher resistance against corrosion and oxidation.
The alloying elements affect the properties of steel in 4 ways :
(a) By strengthening ferrite while forming a solid solution. The strengthening
effects of various alloying elements are in this order : Cr, W, V, Mo, Ni, Mn
and Si.
(b) By forming carbides which are harder and stronger. Carbides of Cr and V
are hardest and strongest against wear particularly after tempering. High
22 alloy tool steel use this effect.
 (c) Ni and Mn lower the austenite formation temperature while other alloying Introduction to
Mechanical Design
elements raise this temperature. Most elements shift eutectoid composition
to lower C % age.
(d) Most elements shift the isothermal transformation curve- (TTT) to lower
temperature, thus lowering the critical cooling rate. Mn, Ni, Cr and Mo are
prominently effective in this respect.
Effects of individual alloying elements on properties of steel :
Sulfur
S is not a desirable element in steel because it interferes with hot rolling and
forging resulting in hot-shortness or hot embitterment. S, however, is helpful in
developing free cutting nature. S up to 0.33% is added in free cutting steel. If steel
is not free cutting S is restricted to 0.05% in open hearth or converter steel and to
0.025% in electric furnace steel.
Phosphorous
P produces cold shortness, which reduces impact strength at low temperature. So
its %age is generally restricted to level of S. It is helpful in free cutting steels and
is added up to 0.12%. It also improves resistance to corrosion.
Silicon
Si is present in all steels but is added up to 5% in steels used as laminates in
transformers, motors and generators. For providing toughness it is an important
constituent in steel used for spring, chisels and punches. It has a good effect in
steel that it combines with free O2 forming SiO2 increasing strength and soundness
of steel castings (up to 0.5%).
Manganese
12 to 14% of Mn produces extremely tough, wear resistant and non-magnetic steel
called Hatfield Steel. It is important ingredient of free cutting steel upto 1.6%.
Mn combines with S, forming MnS. For this purpose Mn must be 3 to 8 times
the S. Mn is effective in increasing hardness and hardenability.
Nickel
Ni is good in increasing hardness, strength and toughness while maintaining
ductility. 0.5% of Ni is good for parts subjected to impact loads at room and very
low temperature. Higher amounts of Ni help improve the corrosion resistance in
presence of Cr as in stainless steel. Nickel in steel results in good mechanical
properties after annealing and normalising and hence large forgings, castings and
structural parts are made in Ni-steel.
Chromium
Cr is common alloying element in tool steels, stainless steels, corrosion resistant
steels (4% Cr). It forms carbide and generally improves hardness, wear and
oxidation resistance at elevated temperature. It improves hardenability of thicker
sections.
Molybdenum
Mo is commonly present in high-speed tool steel, carburising steel and heat
resisting steel. It forms carbide having high wear resistance and retaining strength
at high temperatures. Mo generally increases hardenability and helps improve the
effects of other alloying elements like Mn, Ni and Cr.
Tungsten
W is important ingredient of tool steel and heat resisting steel and generally has
same effects as Mo but 2 to 3% W has same effect as 1% of Mo. 23
Machine Design Vanadium
Like Mo, V has inhibiting influence on grain growth at high temperature. V
carbide possesses highest hardness and wear resistance. It improves fatigue
resistance. It is important constituent of tool steel and may be added to
carburising steel. Hardenability is markedly increased due to V.

Titanium
Addition of Ti in stainless steel does not permit precipitation of Cr carbide since
Ti is stronger carbide former and fixes the C.

Cobalt
It imparts magnetic property to high C steel. In the presence of Cr, Co does not
permit scale formation at high temperature by increasing corrosion resistance.

Copper
Atmospheric corrosion resistance of steel is increased by addition of 0.1
to 0.6% Cu.

Boron
Very small %age (like 0.001 to 0.005) of B is effective in increasing hardness
particularly in surface hardening boriding treatment.

Lead
Less than 0.35% Pb improves machinability.

Aluminum
Al in %age of 1 to 3 in nitriding steels is added to improve hardness by way of
forming A1 nitride. 0.01 to 0.06% A1 added during solidification produces
fine-grained steel castings.
We may also correlate certain desired properties with alloying elements. They are
mentioned below.

(a) Hardenability is improved by addition any or more than one of the

following. Si, Mn, Ni, Cr, Mo, W, B.

(b) Toughness, that is the capacity to absorb energy before fracture

increases with addition of Si and Ni.
(c) The presence, of Cr, Mo and W helps steel to retain strength at high
temperatures.
(d) Cr, Mo and W also help improve resistance against corrosion.

(e) Wear resistance of steel increases when alloyed with Cr, Mo, W and V.

(f) The impact strength at low temperature improves due to Ni.

(g) Cu helps steel achieve better resistance against atmospheric corrosion.

(h) Surface hardenability is improved by addition of Al.

(i) V helps increase fatigue strength of steel.

(j) Steels with S, P and Pb have better machinability.

Table 1.2 describes application, desired properties and composition of several alloy
steels.
24
 Table 1.2 : Applications of Alloy Steels Introduction to
Mechanical Design
Sl. No. Application Desired Properties Composition
1. Rail Steel Strength, ductility, impact and C-04% to 0.6% Mn
fatigue strength and Cr- upto 1%
2. Spring steel (tension, Good elongation, high elastic limit (a) C-0.6, Mn-0.9
compression, torsion) (20 to 30%, 1200-1400 MPa) Si-2.0
(b) C-0.5, Mn-0.8,
Cr-1.0, V-0.15
(c) C-0.5, Mn-0.9
Cr-0.5, Ni-0.6
Mo-0.2
3. Structural steel High strength, toughness, high Wide range of alloy
(bridges building, temperature strength, corrosion steels containing
cars, gears, clutches, resistance several alloying
shafts) elements
4. Weldable steel for Weldability, high resistance to C-0.15 to 0.3% with
welded structures atmospheric corrosion, resistance some Cu and V
to brittle fracture
5. Concrete reinforcing Bend 90o-180o, torsteel with ribs C-0.3 to 0.4%, Min
steel for grater surface area. 0.5 to 0.8%
Elong = 16%
UTS =500-650 MPa C-0.45 to 0.6%,
Y.S. = 35 MPa Mn-0.7 to 1.1%
6. High speed steel for Resist temperature upto C-8%, W-18% Cr-4%,
cutting tools 550-600oC V-1%
Cutting tools requiring high C-8%, W-6%,
hardness at working temperature Mo-5%, Cr-4%, V-2%
18 : 4 : 1 steel and
6 : 5: 4: 2 steel
7. Creep resisting steel Application in pipeline upto Mo-0.4% to 0.6%
400-550oC V-0.25% to 1.0%
Cr-upto 6.0%
Other parts upto 500oC C-low carbon
8. Ball bearing steel Rolling element, inner and outer C-0.9 to 1.1% Cr-0.6
races. High hardness 61-65 Rc to 1.6%, Mn-0.2 to
high fatigue strength 0.4%
9. Hadfield Mn steel Resistance to abrasion ad shock, C-1 to 1.4% Si-0.3 to
excavating and high toughness, strength ad 1.0% Mn-10 to 14%
crushing machine, ductility with Fe
railroad crossing, oil
well, cement, mining
industries. Used as
casting and hot rolled
10. High strength low High strength/weight ratio. C-0.07 to 1.3%, TI, V,
alloy steel (HSLA) Balanced properties such as A1 Co less than 0.5%
for automotive parts toughness, fatigue strength,
weldability and formability

1.17 STAINLESS STEEL

Stainless steel is an alloy steel but has become a class on its own because of widespread
applications. It also has several unique properties. Being steel all types of stainless steel
essentially contains C but they also contain chromium. Many of stainless steels also
contain nickel. The important properties of stainless steels are mentioned below : 25
Machine Design (a) They have wide range of strength and hardness accompanied by ductility.
(b) Stainless steels resist corrosion because very thin hydrous oxide layer forms
on surface, which obstructs further penetration of oxygen.
(c) They exhibit good creep resistance and resist oxidation at elevated
temperatures.
(d) They have good thermal conductivity.
(e) Stainless steels are weldable and machinable.
(f) They can be worked hot and cold.
(g) Since the surface is not corroded, they maintain good surface appearance
and finish.
(h) It does not show a very steep transition (ductility to brittleness) under
impact.
Combination of these properties render stainless steels as the best possible material
against corrosion, chemical attacks, high temp, low temperature and for critical parts that
are required to be small in size. They are also capable to bear high stress concentration
as ductility help plastic deformation under increased stress at stress concentration. Gears,
shafts and springs are made in stainless steel to take advantage of high strength, ductility
and corrosion resistance if sizes have to be keeping smaller. Blades for compressors and
turbine, chemical containers, surgical instruments are made in stainless steel to take
advantage of anti corrosive properties.
There are three major types of stainless steels :
Ferritic Stainless Steel
This is the most abundantly used stainless steel and has ferritic structure because
of which it cannot be heat-treated. It has high resistance against corrosion and
oxidation. It is used in furnace as container of acids and trims of automobiles.
Carbon content of ferritic steel varies from 0.08 to 0.2%, Cr from 12 to 20,
Mn from 1 to 1.5%, and Si is 1.0%.
Martensitic Stainless Steel
This steel has martensitic structure and hence hardness. It can be hardened by
quenching. It is used for table wear, surgical instruments, springs, blades of
turbines and tools like cutting blades. The composition is C-0.01 to 1.2%, Cr-12 to
18%, Mn-1 to 1.2%, Si-0.05 to 1.0, Ni-1.0 to 2.0%. For surgical instruments
0.75% Mo is added. Free machining quality achieved big additional of 0.75% S.
Austenitic Stainless Steels
This steel has austenitic structure. C is less than 0.2 whereas Cr varies between
16 and 24% while Ni from 8 to 22%. Ni helps stabilizing austenite. Mn and Si,
respectively vary between 2 to 10% and 1 to 3%. Addition of 0.15% makes this
steel free cutting. The most widely used variety is 18.8 stainless steel which
contains 18% Cr and 8% Ni. This steel can be easily cold worked and does not
strain harden. It is used for chemical plants, mainly with joints. It is, however,
susceptible to intergranular corrosion.

1.18 CAST IRON

Cast iron plays very important role in engineering practice, as it is one of the commonest
materials for manufacturing of machines and their parts. It is being used since fourteenth
century while steel came in use during 19th century. Casting is a process in which
molten metal is poured in a mould and on solidifying the casting of the shape of mould is
obtained. General properties of cast iron are :
26
 (a) Cheap material. Introduction to
Mechanical Design
(b) Lower melting point (1200oC) as compared to steel (1380-1500oC).
(c) Good casting properties, e.g. high fluidity, low shrinkage, sound casting,
ease of production in large number.
(d) Good in compression but CI with ductility are also available.
(e) CI is machinable in most cases.
(f) Abrasion resistance is remarkably high.
(g) Very important property of CI is its damping characteristic which isolates
vibration and makes it good material for foundation and housing.
(h) Alloy CI may be good against corrosion.
CI is prepared from melting pig iron in electric furnace or in cupola furnace. Electric
furnace gives better quality.
CI contains different elements in addition to Fe. The carbon content of CI is more than
2%. Si Varies between 0.5 to 3.0%. It is very important because it controls the form of C
in CI. S content in CI varies between 0.06 to 0.12% and is largely present as FeS, which
tends to melt at comparatively low temperature causing hot shortness. Mn inhibits
formation of FeS.
Though P increases fluidity of CI a property helpful for pouring it has to be restricted
to 0.1 to 0.3% because it reduces toughness. P is present in the form of FeP.
Mn in CI varies from 0.1 to 1.0% though such a small Mn does not affect properties of
CI. It certainly helps improve upon hot shortness by taking care of S.
Several other alloying elements like Ni, Cr, Mo, Mg, Cu and V may be added to CI to
obtain several desirable properties.
CI containing C in form of cementite is called white cast iron. Microstructure of such CI
consists of pearlite, cementite and ledeburite. If C content is less than 4.3% it is
hypoeutectic CI and if C is greater than 4.3% it is hypereutectic CI. White cast iron has
high hardness and wear resistance and is very difficult to machine, it can be ground,
though. Hardness of white CI varies between 350-500 BHN and UTS between
140-180 MPa. White CI is normally sand cast to produce such parts as pump liners, mill
liners, grinding balls, etc.
CI containing carbon in form of graphite flakes dispersed in matrix of ferrite or pearlite
is classified as grey cast iron. The name is derived from the fact that a fracture surface
appears gray. Gray CI differs in %age of Si from white cast iron while C %age is almost
same. The liquid alloy of suitable composition is cooled slowly in sand mould to
decompose Fe3C into Fe and C out of which C is precipitated as graphite flakes.
Addition of Si, A1 or Ni accelerates graphatisation. The graphite flakes vary in length
from 0.01 to 1.0 mm. Larger flakes reduce strength and ductility. The best properties of
gray CI are obtained with flakes distributed and oriented randomly. Inoculant agents
such as metallic A1, Ca, Ti, Zr and SiC and CaSi when added in small amount cause
formation of smaller graphite flakes and random distribution and orientation.
Grey CI is basically brittle with hardness varying between 149 to 320 BHN and UTS of
150 to 400 MPa. Different properties are obtained by varying cooling rate and quantity
of inoculant agents. It has excellent fluidity, high damping capacity and machinability.
If grey CI is repeatedly heated in service to about 400oC, it suffers from permanent
expansion called growth. Associated with dimensional change are loss of ductility and
strength as a result of growth. When locally heated to about 550oC several times this
material develops what are called fire cracks resulting into failure.
Grey CI is used for clutch plates, brake drums, beds of machine tools and equipments,
counter weights in elevator and furnace, gear reducer casing, motor housing, pump
housing, turbine housing, engine frames, cylinders and pistons. 27
Machine Design Iron castings are sometimes cooled rapidly on the surface to obtain white CI structure
while inside is allowed to cool slowly to obtain gray CI structure. Such a combination is
called chilled or mottled CI. Metal or graphite chillers are used to chill the casting on
outer surface. High hardness and wear resistance on the surface and low hardness and
strength at the core are obtained in chilled CI. Railroad freight car wheels, grain mill
rolls, rolls for crushing ores, hammers etc. are made in chilled CI.
High strength grey CI is obtained by addition of strong inoculating agent like CaSi to
liquid alloy before casting process. UTS in the range of 250 to 400 MPa is obtained.
This CI is called meehanite iron and can be toughened by oil quenching treatment to a
UTS of 520 MPa.
If graphite in CI is present in form of nodules or spherods in the matrix of pearlite or
ferrite the material is called nodular cast iron. The CI has a marked ductility giving
product the advantage of steel and process advantage of CI. It is basically a grey CI in
which C varies between 3.2 to 4.1%, Si between 1.0 to 2.8% while S and P are restricted
to 0.03 and 0.1%, respectively. Ni and Mg are added as alloying elements. Crank shafts,
metal working rolls, punch and sheet metal dies and gears are made out of nodular CI.
The defects like growth and fire cracks are not found in this class of iron. This makes it
suitable for furnace doors, sand casting and steam plants. It also possesses good
corrosion resistance making it useful in chemical plants, petroleum industry and marine
applications.
White CI containing 2.0 to 3.0% C, 0.9 to 1.65% Si, < 0.18% S and P, some Mn and
< 0.01% Bi and B can be heat treated for 50 hours to several days to produce temper
carbon in the matrix of ferrite or pearlite imparting malleability to CI. This class is
known as malleable cast iron and can have as high as 100 MPs of UTS and 14%
elongation. Duet to such properties as strength, ductility, machinability and wear
resistance and convenience of casting in various shapes, malleable CI is largely used for
automotive parts such a crank and cam shafts, steering brackets, shaft brackets, brake
carriers and also in electrical industry as switch gear parts, fittings for high and low
voltage transmissions and distribution system for railway electrification.
Addition of alloying elements such as Ni and Cr provide shock and impact resistance
along with corrosion and heat resistance to CI. These are called alloyed CI : 3 to 5%
Ni and 1 to 3% Cr produces Ni-hard CI with hardness upto 650 BHN and modified
Ni-hard CI with impact and fatigue resistance is produced by adding 4-8% Ni and
4-15% Cr. Ni-resist CI with 14 to 36% Ni and 1 to 5% Cr is alloy CI having good
corrosion and heat resistance.

1.19 NON-FERROUS MATERIALS

A typical jet turbine is made up of several metallic materials. It consists of 38% Ti,
12% Cr, 37% Ni, 6% Co, 5% A1, 1% Nb and 0.02% Ta, and others. All of them are
non-ferrous and example only goes to show that in engineering practice, the non-ferrous
materials are finding increasing applications. They represent, in certain cases, the
advantages of high strength and low weight while in some other cases they surpass the
mechanical strength of ferrous materials. In certain cases metals like copper and
aluminum have no alternative from the wide range of steel and cast iron. Electric
conductor and aircraft bodies are the examples. The aluminium alloys are exclusively
used for cooking utensils, as building materials and for aircraft bodies. Copper alleys are
used as conductor in electric machine, as transmission cables and tubing in heat
exchangers. The non-ferrous alloys also show creep resistance and resistance to
oxidation at high temperatures. However, steel may continue to dominate the scene for
its strength, heat treatability and cost. The cost ratios on per weight basis between other
materials and steel are: Ti alloys-62, Cu alloys-8, Mg alloys-13, Al alloys-80, low alloy
steel-2.4, stainless steel-5.51, gray castiron-1.22.
A large variety of alloys of A1, Cu, Mg, Ni are used for making several parts of machine.
They offer varied advantages of lightweight, favourable weight to strength ratio,
28 machinability, castability and formability. Al alloys are used for their high electrical
conductivity, corrosion resistance, good strength, etc. in such applications as electrical Introduction to
Mechanical Design
conductors, storage tanks, marine parts and air craft parts, etc. Cu and Ti alloys are
similarly used in automotive radiators, heat exchanger, electrical machines, condenser,
builders hardware. There are innumerable uses of non-ferrous materials which may
include man made plastic materials along with metallic alloys and readers are advised to
find uses and corresponding composition of a particular alloy form numerous sources.
We take up material requirement of a particular machine element, called bearing. We
will take up design of bearings in one of units as we move ahead in our studies but
description of materials for one type of two bearings, viz. sliding contact bearing is
taken up in next section.

1.20 BEARING MATERIALS

Bearing is a very important part of machines and materials used for bearings assume
great importance. In general it can be said that a good bearing material should possess
following characteristics :
(a) It should be strong enough to sustain bearing load,
(b) It should not heat rapidly,
(c) It should show a small coefficient of friction,
(d) It should wear less, having long service life, and
(e) It should work in foundry.
Generally it is expected that the journal and bearing would be made of dissimilar
materials although there are examples where same materials for journals and bearings
have been used. When the two parts are made in the same material the friction and hence
the wear are high.
Cast iron has been used as bearing material with steel shafts in several situations.
However, the various non-ferrous bearing alloys are now being used largely as bearing
materials because they satisfy the conditions outlined above more satisfactorily.
Bronzes, babbitts and copper-lead alloys are the important bearing materials that are
widely used in service. Certain copper zinc alloys, that is brasses, have been used as
bearing materials, but only to limited extent. Since brass in general is cheaper, it has
replaced bronze in several light duty bearings.
Table 1.3 describes some bearing bronzes.
Table 1.3 : Bearing Bronzes
Mechanical Properties
Bronze and
Composition % UTS YS % Applications
SAE Number
MPa MPa Elong.
Leaded gun Cu, 86-89; 200 80 10 Bushing
metal, 63 Sn: 9-11; Pb, 1-2.5; P,
0.25 max, impurities,
0.5 max
Phosphor Cu, 78.5-81.5; 167 80 8 Heavy loads
bronze, 64 Sn, 9-11, Pb, 9-11; P,
0.05-0.25;
Zn, 0.75 max
impurities, 0.25 max
Bronze Cu, 83-86; 167 80 8 Bronze backed
backing for Sn, 4.5-6.0; bearings
lined Pb, 8-10; Zn, 2.0; imp,
bearings, 66 0.25 max.
Semi-plastic Cu, 76.5-79.5; 133 10 Soft and good
bronze, 67 Sn, 5-7; Pb, 14.5-17.5; antifriction
Zn, 4.0 max; properties
Sb, 0.4 max; Fe, 0.4
max, imp 1.0 max 29
Machine Design Bearing bronzes are the cooper-tin alloys with small additions of other constituents.
Under conditions of heavy load and severe service conditions, bronzes are especially of
great advantages. They possess a high resistance to impact loading and, therefore, are
particularly used in locomotives and rolling mills bearings. However, they get heated up
fast as compared to other bearing materials, such as babbits. Bronze lined bearings are
easily removed and finished bushings are generally available in stocks.
The alloys of tin, copper, lead and antimony are called babbitts. The tin provides the
hardness and compressive strength to babbitts, copper makes them tough, antimony
prevents shrinkage while lead contributes to ductility. Bearing liners are extensively
made in babbitts for their better antifriction properties than bronzes.
When babbitt is backed up by a solid metal of high compressive strength it gives good
service under high speeds, heavy pressure, impact loads and vibrations. The backing
material could be bronze or steel. A thin layer of high-tin babbitt thoroughly fused to a
tinned bronze or steel has exceptional load carrying capacity and impact strength. In
case of cast iron bearings the babbitt is anchored in place by dovetail slots or drilled
holes because babbitt does not fuse with cast iron. Babbitt bearing linings of dependable
strength and life are made by pouring molten material into bearing, allowing to solidify
and fuse thoroughly and then machining to finished sizes. While the melting point of
babbitt varies between 180 and 245oC, depending upon composition, the pouring should
be done when metal is in fully fluid state. For example, SAE 10 babbitt has a melting
point of 223oC, it should not be poured below 440oC. Some Babbitt materials are
described in Table 1.4.
Table 1.4 : Babbitts (White-bearing Metals)
SAE No. Composition % Application
Sn, 90; Cu, 4-5; Sb, 4-5; Pb, 0.35 max.; Thin liner on bronze backing
10.
Fe, 0.08 max; As, 0.1, Max; Bi, 0.08 max.
Sn, 86, Cu, 5-6.5; Sb, 6-7.5; Pb, 0.35 Hard babbitt good for heavy
11. pressures
Max; Fe, 0.08 max; As, 0.1 max; Bi, 0.08 max
Sn, 59.5; Cu, 2.25-3.75; Sb, 9.5-11.5; Cheap babbitt, good for large
12. bearings under moderate loads
Pb, 26.0 max; Fe, 0.08 max, Bi, 0.08 max.
Sn, 4.5-5.5; Cu, 0.5 max; Sb, 9.25-10.75; Cheap babbitt for large bearing
13. under light load.
Pb, 86.0, max; As, 0.2 max

Copper-lead alloys, containing a larger percentage of lead have found a considerable use
as bearing material lately. Straight copper-lead alloys of this type have only half the
strength of regular bearing bronzes. They are particularly advantageous over babbitt at
high temperature as they can retain their tensile strength at such temperatures. Most
babbitt have low melting point and lose practically all tensile strength at about 200oC.
Typical copper-lead alloys contain about 75% copper and 25% lead and melt at 980oC.
The room temperature tensile strength of copper-lead alloy is about 73 MPa and reduces
to about 33 MPa at about 200oC.
Other Bearing Materials
An extensively hard wood of great density, known as lignum vitae, has been used
for bearing applications. With water as lubricant and cooling medium its
antifriction properties and wear are comparable with those of bearing metals.
Lignum vitae has been used with satisfactory results particularly in cases of step
brings of vertical water turbine, paper mill machinery, marine service and even
roll neck bearing of rolling mills.
More recently, in such cases where use of water as lubricant is necessary,
especially if sand and grit are present soft vulcanized rubber bearings have been
used. A soft, tough, resilient rubber acts as a yielding support, permitting grit to
30 pass through the bearing without scoring the shaft or the rubber.
 Graphite, which is a form of carbon, has been used as lubricant in bronze bearing Introduction to
Mechanical Design
but bearing made entirely of carbon are being used. At low speeds carbon bearings
can carry pressure as high as 6.8 MPa.
Synthetic and natural composite materials, plastic and reinforced plastic are being
used as bearing material. However, their characteristics are not well established as
yet. Powder metallurgy bushing permits oil to penetrate into the material because
of its porosity.

1.21 PLASTIC
Plastic have gained immense popularity as engineering materials. These organic
materials, also know as polymers lack strength of metals and can not stand temperature
higher than 150oC yet they offer the advantages of convenient manufacturing into several
shapes and sizes right from molten state. They can be machined but cannot be formed
from solid state as metals can be done. The plastics have good surface finish; they are
not corroded and are not biodegradable. Due to the last property the plastics are difficult
to dispose off. These materials do not conduct electricity hence are used for making
electrical fittings. They are also bad conductors of heat, hence are used as insulators in
and housing for instruments and equipment, which produce heat inside. The low density
is a strong property of plastic. Heaviest plastic has specific gravity of 2.3 against 7.8 of
steel and 2.7 of aluminum. The plastic content of automobile has gradually increased
from 12 kgf in 1960 to 100 kgf in 1980 and to 150 kgf in nineties. The plastic replaces
several times its weight in metals and automobiles thus become lighter. The plastics
offer advantages like low cost, elimination of finishing processes, simplified assembly,
reduction of noise and vibration.
Polymers are classified into three broad divisions, viz. plastics, fibres and elastomers.
Thermoplastic resins are usually referred to as plastics and have the property of
increasing plasticity, i.e. ability to deform plastically with increasing temperature.
They have long chain structure. Thermosetting resins on the other hand have
three-dimensional network of primary bonds. They do not soften on heating, they
become harder due to completion of any left over polymerization reaction on heating.
Thermoplastics in common use are low density and high density polyethylene, rigid
chlorinated polyvinyl chloride (PVC), polyproylene, ABS, Acrylic and
polytetrafluoroethylene (PTFE). Most of them have maximum use temperature of about
100oC. Only PTFE can be used at higher temperature upto 250oC. This material is used
for bearing. Polyethylene is used in automobile interiors. ABS is acronym for a family of
thermoplastics made of acrylonitrile, butadiene and styrene. ABS is used for making
body of business machine, telephone housing and pipe and fitting in drain waste.
Thermosetting plastics in large number are made and used in industry. They can resist
little higher temperature than thermoplastics have higher insulation against heat and
electricity and have better dimensional stability. Malamine is very popular in consumer
items particularly dinner sets. Most of these plastics like phenolic, epoxy and
malamine are used as bonding agents in plywood and particle boards. Epoxy is also
favoured coating surfaces for prevention of corrosion, improving surfaces and as primer
on automobile body.
Elastomers are the materials, which deform from double the length to ten times original
length. Rubber is an elastomer, which is obtained in liquid form trees but converted into
solid by process of vulcanisation. The use of rubber as shock absorber or vibration
dampner is well known. Styrenebutadiene is an artificial rubber.

1.22 MANUFACTURING CONSIDERATIONS

The subject concerns with the designers intimate understanding of methods of
manufacturing. Any designed object can be given required shape by different methods of
manufacturing and therefore the designer will have to specify the methods wherever he 31
Machine Design prefers a particular method. The selected material will have to be given a renewed
consideration for manufacturing. For example, from stress consideration a gear wheel
made in stainless steel may be better and smaller but its machining and teeth cutting will
cost more as compared to medium carbon steel. The change of tools during machining
operation may cost. Even in modern computer numerically controlled machines bringing
required tool in position will not be cost free besides adding cost at programming stage.
It is therefore, to be considered by the designer if the radit of fillets and shoulders may
be kept same or they must be different. If the keyways can be cut in one setting in more
than one location the cost may be reduced for shaft manufacturing. The pulleys can be
cast or fabricated. The process needs to be examined on the basis of weight and cost.
Sometimes an increased cost may be tolerated if weight is reduced. Similarly a welded
structure from mild steel for the housing of a gear reducer may have to be compared with
the cast structure either in cast iron or steel.
Casting in sand mould or permanent may be a question before designer in many cases.
Although a permanent mould may appear to be a better choice for large number yet the
use of pressure and conditions of melting from batch to batch and high initial cost may
be prohibitive. Casting in general may pose several problems concerning rate of cooling,
change of thickness, intricate nature of product and any subsequent machining need to be
considered. The designer must consider that in casting metal at every location (i.e. a flat
wall and a corner) do not cool at the same rate. If material in adjacent location cools
differentially residual stresses are produced. They may even cause cracking. Such
consideration may require basing thicknesses and radii not only on strength but also
upon rate of cooling. The residual stress may not only cause reduction of strength but
may result into undesirable deformation during subsequent machining. Large thicknesses
or diameter in casting solidify over a much longer period and hence are prone to have
coarse structure and lesser strength. The designer may have to assign a proper heat
treatment to refine internal grain structure.
The designer ought to take note of the fact that in forging the deformation is
concentrated more on the surface and inner material is not worked. In hot forging
process therefore the structure of material is more liable to be refined on the surface
creating non-uniformity of structure in the entire body. The refinement is often
advantageous with improved strength, though defects are also some times created in
severely worked material. On the other hand process like rolling, extruding and pressing
are not confined to only surface in their effects. They result in uniform structure in the
end. Cold processes are performed on softer alloys but stronger materials like steel are
often worked hot. Cooling will eventually follow which if not controlled and slow can
result in residual stresses. Anticipating the cooling stresses the designer may recommend
the rate of cooling.
Plastic parts are often cast in moulds made individually or in pressure die cast. The
design must keep minimum thickness within limit, not below 4.5 mm. The pressure die
cast plastic may not require finishing by machining but cast parts need machining and
hence proper thicknesses are to be provided. Very few parts of plastic are made by
machining but designer must take care of temperature rise during cutting process. Slight
rise in temperature may cause material to join by the side of machine surface. Internal
threading has to be performed much more carefully. They can be better made during
casting, 13 threads per cm can be cast easily. The colour of casting is difficult to
maintain which creats problem in assembling parts. To avoid mismatch the surfaces may
be spotted or streaked.
SAQ 3
(a) Classify steel and state application of stainless steel.
(b) Why is medium carbon steel preferred for making machine parts?
(c) What heat treatments are given to medium carbon steel? What are the
benefits from such treatments?
32
 (d) Differentiate between steel and CI. Contrast properties of plain C steel and Introduction to
Mechanical Design
CI and state use of CI.
(e) How could you make CI ductile?
(f) Classify CI and mention uses of each type.
(g) Mention non-ferrous materials, which are used in machines and structures.
What are bearing materials?
(h) Mention compositions of phospher bronze, semi-plastic bronze and a babbit
metal, which are used on bronze backing.
(i) Describe non-metallic materials that are used as bearing materials.
(j) Distinguish between two classes of plastic. Mention advantages of plastics
as engineering material and describe at least five uses.
(k) What manufacturing consideration a designer has to make? Give examples
of cutting, casting and forging processes in respect of metals. Which of
these processes will be applicable to parts made in plastics?

1.23 HEAT TREATMENT

Heat treatment is the process through controlled heating and cooling of metal to induce
desired properties. The process causes changes in the structural arrangements in the
structure of the metal. The structure of an alloy is made up of different phases, which
precipitate from molten mixture depending upon the rate of cooling. The reader may like
to improve familiarity with phases by revising parts of Material Science and we will
ignore such details in this text. The medium carbon steel, high carbon steel and alloy
steel are especially sensitive to heat treatment. Several handbooks describe heat
treatments of several classes of steel. It will suffice here to give brief description.
Annealing
The steel is heated slightly above the critical temperature cooled slowly, often
keeping material in the furnace and shutting off heat. The annealing will result in
uniform grain structure, reduced strength and hardness and increased ductility.
Internal stresses which might have resulted from previous treatment (mechanical
or thermal) are removed by annealing.
Normalising
The heating is same as in annealing but the metal is cooled faster by placing it out
of the furnace. This treatment removes effect of any previous heat treatment and
prepares the metal for further treatment.
Quenching
Quenching is rapid cooling at different rates. It is achieved by immersing the
heated metal from above critical temperature into cold water or any other cooling
medium. The quenching results in high hardness. Steels develop high hardness by
retaining iron carbide which forms at critical temperature and does not find time to
decompose as the cooling occurs very fast. Cooling media such as ice water, cool
water, oil, hot oil, molten salts and molten lead are used depending upon desired
cooling rate. The result of quenching is increased hardness and strength and
decreased ductility while improper quenching may result in surface cracks. 33
Machine Design Tempering
Some of the lost ductility due to quenching is restored through tempering. In this
process the quenched metal is heated to some pre-decided temperature and metal
is soaked for some time. The range of temperature used for steel is generally from
200oC to 600oC and cooling is done in the furnace. The tempering treatment also
helps remove internal stresses, which are created due to hardening treatment. UTS,
YS and hardness reduce while % elongation, impact strength increase due to
tempering at temperatures of 300oC and above. There is little effect on these
properties below 300oC.

Casehardening
Casehardening is a surface hardening process, often applied on low carbon steels
which do not responded to heat treatment. The process consists in packing the
steel piece in charcoal powder and covered from outside. The charcoal powder
cuts of air. When heated in a furnace the carbon from charcoal penetrates the
surface and on quenching the carburized surface retains hardness. The process is
also known as carburizing and steels containing 0.1 to 0.25% C are easily
carburized. The mechanism of hardening is two fold. Firstly the carbon of iron is
very hard and due to quenching it is retained in the surface. Secondly due to
increase in C in the surface layer, the residual compressive stress is produced.
Surface hardening is advantageous in case of gear teeth since the inner bulk
material still remains softer and tougher and thus combined advantage of harder
surface and tougher core mereases the life.
It may be pointed out here that surface is the weakest region of the material in any
form. Fatigue cracks initiate late in hard surface and the wear resistance in also
better.
Besides carburizing by packing there are other methods of surface hardening of
steels. In gas carburizing the metal is heated in gas atmosphere in controlled
manner to avoid oxidation and permit absorption of the gas in the surface. The
gasses used for the purpose are natural gas, coke oven gas, butane or propane. In
the process called cyaniding the steel part is heated covered with the mixture of
potassium ferrocyanide and potassium bichromate. In some cases the mixture is
replaced by powdered potassium cyanide. A very hard case is produced by
cyaniding. A thin hardened layer is produced by immersion of part in the heated
cyanide solution. Natriding is yet another method of case hardening. It consists in
heating the part in the presence of dissociated ammonia in the range of 570oC
to 610oC.
The surface hardness of 60 Rockwell C associated with core hardness of 33 to
38 RC is produced by carburizing. Nitriding can produce surface hardness upto
70 RC and core hardness of 27 to 47 RC. Natrided parts can be tempered. All
steels can be nitrided but those containing aluminum develop very high hardness.
Nitralloy 135 and 135 modified is a highly preferred material for gears. It contains
C-0.35/0.41, Mn-0.55, Si-0.3, Cr-1.20/1.60, Al-1.00, Mo-0.20/0.35. This material
develops surface hardness of 65-70 and core hardness of 30-36 RC. AISI 4340
(C-0.40, Mn-0.70, Si-0.30, Cr-0.80, Mo-0.25, Ni-1.00) and AISI 4140 (C-0.40,
Mn-0.90, Si-0.30, Cr-0.95, Mo-0.20) are two other steels, which are nitrided and
used to make gears.
The high frequency current when passed through body of a part results in surface
heating. Once heated this way, the part is quenched in water. This treatment
resulting into hardened surface is called induction hardening for which steels
containing 0.4 to 0.5% C is good.

34
SAQ 2 Introduction to
Mechanical Design
(a) Sketch diagram for mild steel and compare with diagram of
other ductile material.
(b) Define elastic constants for isotropic material and give their correlation.
(c) Define hardness and state how is the hardness of metal measured. How is
UTS related to hardness?
(d) What do you understand by fatigue strength and enumerate factors that
affect fatigue strength?
(e) Describe three stages of creep.
(f) What is the use of information obtained from impact test?

1.24 SUMMARY
Design is a decision making process in which a designer formulates the problem in clear
terms, finalies several alternatives, selects the best solution, analyzes the best solution,
selects material and determines dimensions. The process allows for modification to
achieve improvement at each step. The results are presented in form of a report which
will necessarily contain drawings, instructions for heat treatment, special processes, etc.
The designer of machine is required to have comprehensive knowledge of mechanical
engineering so that he understands clearly the various forces that act upon several parts
of machines and circumstances in which the machine and its parts have to perform. The
designer must be conversant with methods of analyzing stress through theoretical,
experimental and numerical methods. He may depend upon one or two of them so that he
can analyze a part completely. The designer should be sensitive to human needs,
capabilities and sensibilities so that his design fulfills the objective, can be operated and
maintained by common person and pleases him to possess.
The engineering materials are used to make machine parts and there exist several of
them. They are all used to serve specific purpose based upon properties. The properties
that designer of machine will use will be related to strength and material behaviour under
load. The properties normally needed by machine part are yield strength, ultimate tensile
strength, percent elongation, toughness and resilience. They are determined from tension
test on universal testing machine. The hardness and impact strength, though not used in
direct calculation are used for selecting materials for specific purposes. Fatigue and
creep are behaviours and conditions of varying load and constant load acting over a long
period respectively. While latter is a condition to be considered only in case of higher
temperatures, fatigue is the type of loading to which all machines, machine parts and
structure are subjected. Fatigue strength, which is defined as the stress at which material
will never fail, no matter how many times that stress varies, then appears to be the only
important property on the basis of which machine parts must be designed. However,
while on one hand its determination is difficult, on the other hand it has a definite
relationship with ultimate tensile strength (UTS). Hence UTS can be used as design
basis after fully understanding several factors that influence fatigue strength.
Out of several metallic materials steel is the most common choice because of such
reasons as easy availability, good strength, workability, ductility and heat treatability.
Cast iron is another good ferrous material preferred to produce casting for its
availability, hardness, compressive strength and damping properties. Plain carbon steel,
containing Mn, Si, S and P in addition to carbon with large proportion of iron is divided 35
Machine Design into three types, viz. low carbon (0.08 to 0.27% C), medium carbon (0.28-0.57% C) and
high carbon (0.58 to 1.2% C) steels. Additionally Cr, Mo, Ni, V, Co, Al, Cu, etc. may be
added to obtain series of alloy steels which have better mechanical properties with
increased cost. Three types of stainless steels (ferritic, austenitic, martensitic) are in
common use for their corrosion and oxidation resistances. Each alloying element imparts
particular characteristic to steel. Steel of all types are heat treatable except low carbon
steel. They, however, can be case hardened like medium carbon and some alloy steels.
Plastics are being used for making parts of machines because they are light in weight.
However, they cannot compete with metals in strength. Non-ferrous metals which are
mainly alloys of aluminum, copper, zinc, magnesium, nickel, etc. are used for specific
reasons of weight and properties. They are invariably used in sliding bearings.
The designer has to consider the available manufacturing processes and effects of such
processes on final product.

1.25 KEY WORDS

Mechanical Properties : Mechanical properties of the metals are those
which are associated with the ability of the
material to resist mechanical forces and load.
Strength : It is the ability of a material to resist the externally
applied forces without breaking or yielding.
Stiffness : It is the ability of a material to resist deformation
under stress.
Elasticity : It is the property of a material to regain its original
shape after deformation when external forces are
removed.

1.26 ANSWERS TO SAQs

Refer the preceding text for all the Answers to SAQs.

36