PSD Impt Questions
PSD Impt Questions
PSD Impt Questions
UNIT 1
1. A separately excited motor of 220V, 960rpm, 80A with an
armature resistance of
0.06ohms is coupled to an over hauling load with a toque of 100 Nm.
Compute the speed at which the motor can hold the load by
regenerative braking. Source voltage is 220V. Neglect the motor
rotational losses.
UNIT II
1. Explain the operation of a three-phase semi converter fed DC
separately excited motor in continuous current mode and derive the
equation relating speed and torque and also draw their speed torque
characteristics.
2. Explain the operation of a three phase semi converter fed DC
series motor in continuous current mode and derive the equation
relating speed and torque and also draw their speed torque
characteristics.
3. Explain the operation of a three phase full converter fed DC
separately excited motor in continuous current mode and derive the
equation relating speed and torque and also draw their speed torque
characteristics.
4. Explain the operation of a three phase full converter fed DC series
motor in continuous current mode and derive the equation relating
speed and torque and also draw their speed torque characteristics.
5. A 80KW, 440V, 800rpm, DC motor is operating at 600rpm and
developing 75% rated torque is controlled by 3-phase, 6-pulse
thyristor converter. If the back emf at the rated speed is 410V,
determine the triggering angle of converter. The input converter is
3- phase, 415V, 50Hz,AC supply?
Important questions
Unit III
1. Explain the regenerative braking method used for DC series and
separately excited motors with neat circuit diagrams.
10. What should be the value of the firing angle to get the
rated torque at 800rpm?
Compute the firing angle for the rated braking
torque at 1200rpm.
Calculate the motor speed at the rated torque and alpha =1650
for the regenerative braking in the second quadrant?
Important questions
UNIT IV
1. Explain the operation of single quadrant chopper fed DC series and
separately excited motor in both circulating current and non-
circulating modes and also draw their speed torque characteristics.
2. Explain why stator voltage control is suitable for sped control induction motor in fan and
pip drives. Draw a eat circuit diagram for speed control of scheme of 3-phase induction
motor using Ac Voltage controller.
3. Using 3-phase solid state AC Voltage Controllers explain clearly how it is possible to
achieve 4 quadrant operation of 3 phase induction motors.
4. Explain why stator voltage control is suited for speed control of induction motors in
driving fan loads.
7. List the various methods of speed control from stator side of a three phase Induction
motor and complete their merits and limitations.
Important questions
UNIT VI
1. A 5 H.P., 4 pole 50Hz, 3 phase induction motor is fed through a cyclo-converter of
frequency f/3 calculate speed of the motor at a slip of 5 percent.
2. A pole changing method of speed control is not popular in case of induction motors why.
4. For speeds below synchronous speed v/f ratio is kept constant in variable frequency control
of inductor motor why.
5. Explain a speed control scheme for a three-phase inductor motor, which uses a
cycloconverter.
6. Explain the operation of PWM inverter fed three phase induction motor. Bring out its
merits
Important questions
UNIT VII
1. What are the advantages of static rotor resistance control (using diode bridge and switch
controlled resistor) over conventional methods or rotor resistance control?
2. Why is the power factor of the slip power recovery scheme of speed control of indication
motor low?
3. Why a resistance starter is generally required for the induction motor drive employing slip-
power recovery? Can you use a semiconductor switch controlled resistance connected after
the diode bridge to avoid resistance starter?
4. Why has the static Kramer Drive a low range of speed control?
5. Explain the principle of and an application of variable speed and constant frequency
generation schemes.
6. Compare the various types of single phase induction motors in terms of performance and
explain where they are employed.
Important questions
UNIT VIII
1. Write short notes on the following (i) 3-phase semi controlled converters (ii) Cyclo
converters (iii) Static Kramer drives
2. In a self-controlled synchronous motor fed from a variable frequency inverter (i) The rotor
poles invariably have damper windings (ii) There are stability problems (iii) The speed of
the rotor decides stator frequency. (iv) The frequency of the stator decides the rotor speed.
3. In self-control mode drive of syn. Motors, damper windings are not needed. Why?
4. What are different types of rotor position sensors used in self-controlled synchronous
motor drive?
6. Derive expressions for no of revolutions made by the motor from rated speed to rest.
7. A 400V 8 pole 3-pha se synchronous motor and its load have a total moment of inertia of
630Kg-m2. Determine the time and the number of revolutions made by it to come to stand
still if theocratic braking is employed which gives and initial electric braking torque of
690Kg-m2.Assume a frictional torque of 1.4Kg-m.