Instruction Manual

Preface

Preface
Thank you for purchasing this product.
Before using this product, read this document carefully so that you can use this product correctly and safely.

-i-
For safe usage

For safe usage

This document uses symbols for warnings, cautions, and prohibitions. These symbols and their meanings are
as follows. Please make sure you fully understand the meanings of these symbols before reading the rest of
this document.

Indicates an item for which incorrect handling can result in a major

WARNING accident involving death or serious injury.

Indicates an item for which incorrect handling can lead to injury or

CAUTION damage to property. Under certain conditions, more serious
consequences may result.

PROHIBITED Indicates a prohibited method of handling.

MANDATORY Indicates a mandatory method of handling and a forcible item.

WARNING and CAUTION for handling this product

WARNING
Do not perform any work while the vehicle is running.
Doing so could result in an accident.
Always observe the following rules. Failure to do so can result in heat generation, fire, blowout, or
electrical shock.
- Do not disassemble or alter this product.

- Do not connect this product to anything with a voltage exceeding the ratings of this product.

- Do not connect the probe to any parts applied by a voltage exceeding the ratings of this product.

CAUTION
<Work environment>
Do not work anywhere that water could come in contact with the equipment.

Block the wheels of the vehicle with chocks before carrying out work.
Failure to do so could result in an accident.

- ii -
For safe usage

CAUTION
When working anywhere hardly visible, for example under the vehicle, always make the vehicle
starter switch (ignition switch) OFF to ensure that the vehicle cannot be moved.
Failure to do so could result in an accident.
When working near the engine compartment, be careful of the engine and other high-temperature
parts.
High-temperature parts can cause burns.
Do not route the cable of this product over the engine compartment, especially if the engine is
running.
Failure to follow this instruction could result in an accident by catching up the cable and clothes with the
belt and pulley.
Do not use this product in an extremely dusty environment.

<Checking before use>

Inspect for adhesion of foreign materials to or pin breakage of each connector of this product
before use.

Before connecting the datalink cable to this product and the vehicle side diagnosis connector,
inspect to see if each connector is contaminated with foreign materials or the connector pins are
damaged.
<Handling of the product and equipment>
Do not drop this tool or subject it to a strong impact.

When connecting the datalink cable to this product and the vehicle side diagnosis connector or
disconnecting it from them, ensure correct orientation of the connector and gently put it straight in.
If the connector is connected in the wrong orientation, or put in or pulled out at the wrong angle, there is a
risk of damaging the connector terminal and this may cause malfunctioning of the vehicle and/or this
product.
When connecting the USB cable to this product and a PC or disconnecting it from them, ensure
correct orientation of the connector and gently put it straight in.
If the connector is connected in the wrong orientation, or put in or pulled out at the wrong angle, there is a
risk of damaging the connector terminal and this may cause malfunctioning of the PC and/or this product.
When pulling out the connector of datalink cable or USB cable, hold the connector section not the
cord.
Pulling on the cord section can break the lines in the cable.
Do not lift or drag this product by holding the cable connected to this product. When moving or
installing, move this product by holding with hands.

Do not apply the load causing stress to the connector connected to this product.
Applying too much force could result in breaking the connector terminal and this may cause malfunctioning
of the vehicle, the PC and/or this product.
<Usage restrictions>
Do not use a datalink cable other than the dedicated datalink cable supplied with this product.

- iii -
For safe usage

CAUTION
When you start this product only by USB power (BUS power), be careful not to set the PC to, "low
power consumption mode" / "suspend mode".

The USB port to be connected to this product requires a power supply capability of 500 mA
current source.
As for connecting this product to the PC, directly connect it to the USB port on the PC or via a
USB hub that has the capability of supplying sufficient current.
Some types of USB hubs may have insufficient power supply capability for normal operation. (For
example, a hub on PC keyboard is not suitable for this connection.)
<Storage and maintenance of the product>
Do not expose this product to direct sunlight for long periods of time.

Do not use solvents or thinners such as benzine when cleaning.

To do so could cause deformation, discoloration, cracking, etc., and also result in loss of functions. To
clean, wipe gently with a soft damp cloth with diluted neutral detergent.
<Disposal of the product>
When discarding the product or its accessories, contact authorized industrial waste-disposal
service.
Those who discard waste without authorization will be punished by law.

Disposal Requirements
The product shall be disposed in accordance with all applicable legislation for disposal of Electrical and Electronic
Equipment in each country and region. (e.g. WEEE Directive in EU)
Please contact our authorized distributor or our sales agent when disposing it.

- iv -
For safe usage

WARNING and CAUTION for Bluetooth (models with Bluetooth)

WARNING
Do not use this product near medical devices or inside medical facilities as it may affect electronic
devices with medical applications.

Make sure to keep this product at least 22 cm away from persons wearing a pacemaker.
Radio wave could affect the performance of pacemaker.
Do not use this product near an automatic control device such as an automatic door or a fire
alarm.
Radio wave could effect its operation and result in an accident caused by malfunction.
Do not use this product in electric trains, airplanes, or places where flammable gasses are
present.
Failure to do so may result in accidents.

CAUTION
The communication range depends on any obstacles (i.e., human bodies, metal, walls) between
this product and the Bluetooth device, and the condition of the radio wave.
An antenna is built into this product. The sensitivity of the Bluetooth communication is maximized
when no obstacles exist between the connected Bluetooth device and the antenna of this product.
The communication distance becomes shorter should there be obstacles between the antenna of
the connected Bluetooth device and the built-in antenna of this product.
The following circumstances could affect the sensitivity of the Bluetooth communication.
- Obstacles such as human body, metal, wall, etc.
- In close proximity to established wireless networks, microwave ovens, and other devices that
emit radio waves.
Since Bluetooth devices and the wireless LAN (IEEE802.11 b/g) use the same frequency band
(2.4 GHz), radio wave interference could occur and cause degradation of communication speed,
noise and disconnection if a Bluetooth device is used near a wireless LAN equipped device.
To resolve poor communications, perform the following steps.
- Place this product as close to a Bluetooth device as possible.
- Keep a wireless LAN equipped device away from this product as much as possible.
- If communications do not improve, turn off any wireless LAN equipped devices nearby.
Use the USB cable for more data critical situation over the Bluetooth communication (wireless)
due to the greater possibility of loss of connection during data upload or download of the data
transmission.
Please note that we shall have no liability for any information leakage from the Bluetooth
communication.

-v-
For safe usage

The countries where you can use the models with Bluetooth
Japan, USA, Canada, Australia, New Zealand, EU (Europian Union), Malaysia, Indonesia
* In the countries other than those above, you cannot use the models with Bluetooth.

Trademarks
Microsoft, Windows, Internet Explorer, Windows 10, Windows 8.1, Windows 7, Windows Vista are the
trademarks or registered trademarks of the Microsoft Corporation of the United States in the United
States and other countries.
Bluetooth is the trademark or registered trademark of Bluetooth SIG, Inc. in the United State and other
countries.
Names of products and companies in this document are registered trademarks or trademarks of their
owners.

TRON, iTRON and iTRON are not the names for specific products and series of products.
TRON is an abbreviation of "The Real-time Operating System Nuceus".
iTRON is an abbreviation of "Micro Industrial TRON".

- vi -
Table of contents

Table of contents
1 Before Use
1-1 Product Configuration .......................................................................................................................... 1
Components ............................................................................................................................................ 1
1-2 Names of the Parts .............................................................................................................................. 2
models without LCD ................................................................................................................................ 2
1-3 Setup.................................................................................................................................................... 3
Required operating environment of the PC ............................................................................................. 3
Necessary Setup ..................................................................................................................................... 4
1-4 Connection........................................................................................................................................... 5
Connecting to the vehicle ........................................................................................................................ 5
Connecting to a PC ................................................................................................................................. 6

2 Basic Operations
2-1 Starting................................................................................................................................................. 7
2-2 Ending.................................................................................................................................................. 7

3 Indicator
3-1 Indicator ............................................................................................................................................... 8

4 Product Specifications
4-1 Specifications of This Product.............................................................................................................. 9

5 Warranty
5-1 Warranty............................................................................................................................................. 10

- vii -
1 Before Use

1 Before Use
1-1 Product Configuration
Check that you have all of the following standard components before using this product.

Components
Set Part Number: 95171-0106* (without LCD, without Bluetooth)
95171-0107* (without LCD, with Bluetooth)

No. Part Name Illustration Part No. Q'ty

1 Main unit 1
T01866Z

without LCD

2 Datalink Cable 95171-1283* 1

T01857Z

3 USB Cable 95171-1011* 1

T01871Z

4 USB Spacer 95171-1302* 1

T02747Z

5 Instruction Manual (this document) 1

NOTE
The last figure of a part No. is indicated with *. When you ask for information, make inquiries with the
9-digit part No. and part name.

-1-
1 Before Use

1-2 Names of the Parts

The names of the product parts are as follows:

models without LCD

Overall

Indicators
* For detailed information about indicators, refer to "Chapter 3 Indicator/3-1 Indicator".

Upper side

USB connector* DC jack*

Connector for datalink cable

* Rubber caps are provided for "USB connector" and "DC jack".

T01896E

-2-
1 Before Use

1-3 Setup
You must carry out the setup necessary for use of this product.

Required operating environment of the PC

For using this product, a PC with following operating environments is required.
OS:
Microsoft Windows Vista (SP2) (32bit, 64bit) English version
Microsoft Windows 7 (SP1) (32bit, 64bit) English version
Microsoft Windows 8.1 (32bit, 64bit) English version
Microsoft Windows 10 (32bit, 64bit) English version
With USB 2.0 interface as standard
Internet Explorer 8.0 or later version should be installed.
Access to Internet is allowed. (Broadband internet connection is recommended)

NOTE
If this product is used as the interface, the operating environment of the software on a PC side is
needed in addition to the above operating environment.

-3-
1 Before Use

Necessary Setup
For using this product, following setup is needed.
Installing DST-i setup software to a PC (all models)
A dedicated USB driver, the setup utility (DST-i configuration tool), etc. which is required for connecting this
product and a PC using a USB cable or Bluetooth shall be installed to the PC.
Installing the DST-i main unit software to this product (all models)
Install the DST-i main unit software to this product.
Installing Bluetooth driver software and Paring to a PC (models with Bluetooth)
For the models with Bluetooth, to connect this product with a PC through the Bluetooth communication function,
you must install the Bluetooth driver software to the PC beforehand.
In addition, you must execute pairing between the PC and this product.

CAUTION
Do not connect this product with a PC using the USB cable before the DST-i setup software
installation to your PC is completed.
To install the DST-i setup software to a PC, log on with administrator privileges and close all running
applications before installation.
In installing the DST-i main unit software, execute the install by using the USB cable in the state that
this product and the PC are connected.
Do not execute the install in using Bluetooth communication.
Use of a Bluetooth driver software equipped as standard to the PC with Windows Vista or later
version is recommended for use of a Bluetooth driver.
This information does not guarantee the connection between all of commercially available
Bluetooth modules and information terminals equipped with Bluetooth (e.g., PC and cellular
phone).
Use a Bluetooth module that is labeled with the Bluetooth logo mark and conforms to the Bluetooth
standard 2.0.
Total eight Bluetooth modules and information terminals having Bluetooth can execute paring with
this product. If ninth Bluetooth module or information terminal executes paring, first Bluetooth
module or information terminal will be cancelled.

1. Access the following website and setup the this product and the PC following the displayed
instructions.
http://www.ds3.denso.co.jp/dst-i/setup/

-4-
1 Before Use

1-4 Connection

Connecting to the vehicle

Use the datalink cable to connect this product with the vehicle.
Check the position of the diagnosis connector of the vehicle side in the repair manual of the vehicle.

Connected to vehicle side diagnosis connector

Notch (Center)

Tighten with screws. T01898E

NOTE
The power supply of this product is turned ON when this product is connected to a vehicle with the
datalink cable.

-5-
1 Before Use

Connecting to a PC
Use a USB cable to connect this product to a PC.

Connected to the USB connector into the PC

USB cable

T01919E

NOTE
The power supply of this product is turned ON when this product is connected to a PC with the USB
cable.
When the USB communication with the PC is established, the PC communication (USB) indicator on
this product lights or flashes in green.
When establishing the connection with the Bluetooth communication function on the models with
Bluetooth, USB cable connection is not needed.
If connecting with a PC with the Bluetooth communication, communication setup must be performed
with the DST-i configuration tool.
When the Bluetooth communication with the PC is established, the PC communication (Bluetooth)
indicator on this product lights or flashes in blue.
When connecting the model with Bluetooth to a PC with the USB cable, the USB communication has
the top priority in the communication between a PC.
When communication way is changed from USB to Bluetooth while communicating, remove the USB
cable with the PC application software finished.

CAUTION
You must install the DST-i setup software on your PC before you connect the USB cable to your PC.
Reference: Page 4 Installing DST-i setup software to a PC (all models) (Chapter 1 Before Use/Setup/Necessary Setup)
When the PC does not supply adequate power, please contact your distributor.

-6-
2 Basic Operations

2 Basic Operations
2-1 Starting
1. Connect this product and the vehicle side diagnosis connector with the datalink cable.
Reference: Page 5 Connecting to the vehicle (Chapter 1 Before Use/Connection)

NOTE
The power indicator turns green when this product is connected to a vehicle with the datalink
cable.

2. Connect this product and a PC with the USB cable.

Reference: Page 6 Connecting to a PC (Chapter 1 Before Use/Connection)

NOTE
If you use a model with Bluetooth and connect with a PC through the Bluetooth
communication function, you do not need to connect with the USB cable.

3. Turn the vehicle starter switch (ignition switch) ON.

NOTE
When the vehicle starter switch (ignition switch) position is OFF or ACC, communication with
the vehicle cannot be established. Turn the vehicle starter switch (ignition switch) ON or start
the engine when using this product.

2-2 Ending
1. Finish communications with the vehicle by PC application software.

CAUTION
Do not disconnect the datalink cable from this product during the active test. The diagnosed
actuators could be stopped still in the drive status. Make sure to execute the ending
procedure after finishing the active test.

2. Turn the vehicle starter switch (ignition switch) OFF.

3. Disconnect the USB cable from this product and the PC.

4. Disconnect the datalink cable from this product and the vehicle side diagnosis connector.

-7-
3 Indicator

3 Indicator
3-1 Indicator
The indicators of this product provide the following information by their illumination.

[Power] indicator
[Error] indicator

[Vehicle] indicator
[PC (USB)] indicator
[PC (Bluetooth)]
indicator T01900E

[Power] indicator
Shows the status of power.
Lights in green during power ON.
[Vehicle] indicator
Shows the status of communications with the vehicle.
Flashes in green during active communications.
[PC (Bluetooth)] indicator
Shows the status of Bluetooth communications with the PC.
Flashes in blue during active communications.
[PC (USB)] indicator
Shows the status of USB communications with the PC.
Flashes in green during active communications.
[Error] indicator
Lights or flashes in red when an error occurs.

-8-
4 Product Specifications

4 Product Specifications
4-1 Specifications of This Product
Item Specifications
OS iTRON
CPU 32-bit RISC microcomputer
Built-in Flash ROM 16 MB
Memory SDRAM 16 MB
EEPROM 32 KB
USB USB 2.0 x 1
Bluetooth *1 Bluetooth 2.0 class 1
External interface *2 DC jack JEITA4 standard type
Dedicated connector (D-sub 25 pin) x 1
Vehicle communication
ISO9141, CAN
Main unit power Vehicle power supply DC 6.5 to 32 V (Datalink cable)
supply voltage USB power (BUS power) DC 4.75 to 5.25 V *3
Power consumption Normally 1.5 W (12 VDC), Max. 2.5 W (12 VDC)
Operating temperature
Operating 0 to 50C [-10 to 60C]
[Storage temperature]
environment
Operating humidity 35 to 85% (No condensation)
Dimensions 135 mm (W) x 70 mm (H) x 35 mm (D)
Model without Bluetooth Approx. 160 g
Weight
Model with Bluetooth Approx. 165 g
*1 For models with Bluetooth only
*2 Some functions require the support software.
*3 This product can be turned on by the power supplied from the USB power (BUS power). However, vehicle
communication cannot be established when the power is not supplied from the vehicle.

-9-
5 Warranty

5 Warranty
5-1 Warranty
1. The warranty period of this set is two years after the purchase day. However accessories are not covered, main
body only.

2. Free repair warranty is applied only for the failure under proper operation conditions within the warranty period.

3. Non-free repair is applied to the following cases even if the valid warranty period remains.
Failure or damage from fire and natural disaster.
Failure or damage as a result of a falling during transportation and movement after purchase or from the
improper handling.
Failure or damage caused from handling in a way contrary to proper operating methods and cautions described
in this document.
Failure or damage from modification or liability for operations.
Replacement of external parts such as the resin case.

4. We shall have no liability for any direct or indirect damage resulting from failure or use of this product.

5. For request of repair, please contact your distributor.

Data preservation
Recorded data in this product could be lost in repair. Please note that we shall have no liability for any damage and
data preservation derived in conjunction with data loss.

- 10 -
5 Warranty

DENSO Overseas Subsidiary Company & TAS CORPORATION

name/Address Tel/Fax
DENSO AUTOMOTIVE SYSTEMS AUSTRALIA PTY. LTD. Sales:
Address: 2-46 Merrindale Drive, Croydon, Victoria 3136, Australia Tel: +61-3-8761-1400
Fax: +61-3-8761-1505
Service:
Tel: +61-3-8761-1449
Fax: +61-3-8761-1505
DENSO INTERNATIONAL ASIA PTE. LTD. Sales & Service:
Address: 51 Science Park Road, #01-19 The Aries, Science Park II, Tel: +65-6776-8268
Singapore 117586 Fax: +65-6776-8698
PT. DENSO SALES INDONESIA Sales & Service:
Address: JL.Gaya Motor I, Sunter II, Kel Sungai Bambu, Tel: +62-21-651-2279
Tanjung Priok, Jakarta Utara, Jakarta-Indonesia Fax: +62-21-651-2284
DENSO (MALAYSIA) SDN. BHD. Sales & Service:
Address: Lot 2, Jalan P/1, Section 13, 43650 Bandar Baru Bangi, Tel: +60-3-5569-9933
Selangor Darul Ehsan, Malaysia Fax: +60-3-5567-3301
PHILIPPINE AUTO COMPONENTS, INC. Sales & Service:
Address: 109 Unity Avenue, Carmelray Industrial Park 1, Tel: +63-49-549-3030
4037 Canlubang, Calamba City, Laguna, Philippines Fax: +63-49-549-3089
DENSO TAIWAN CORP. Sales & Service:
Address: 525, Sec. 2 Mei Su Road Yang Mei Town Taoyuan Hsien, Tel: +886-3-482-8001
Taiwan, R.O.C. Fax: +886-3-482-8003
DENSO SALES (THAILAND) CO.,LTD. Sales:
Address: 888 Moo 1, Bangna-Trad Rd. Km. 27.5, Tambol Bangbo, Tel: +66-2-315-9500
Amphur Bangbo, Samutprakarn 10560 Thailand Fax: +66-2-315-9556
Service:
Tel: +66-2-315-9500
Fax: +66-2-315-9557
DENSO EUROPE B.V. Sales & Service:
Address: Hogeweyselaan 165, 1382 JL Weesp, The Netherlands Tel: +31-294-493-493
Fax: +31-294-417-122
DENSO SALES MIDDLE EAST & NORTH AFRICA FZE. Service:
Address: P.O.Box 261986, Jebel Ali Free Zone South, Dubai, Tel: +971-04-880-7789
United Arab Emirates Fax: +971-04-880-7790
DENSO (CHINA) INVESTMENT CO.,LTD. Sales:
Address: Room No.518, The Beijing Fortune Building, Tel: +86-10-6590-8025
No.5 Dong San Huan Bei Lu, Chaoyang District, Beijing, Fax: +86-10-6590-8065
100004, China Service:
Tel: +86-10-6590-8021
Fax: +86-10-6590-9044
DENSO INTERNATIONAL INDIA PVT. LTD. Sales & Service:
Address: Plot No.3, Sector-3, IMT Manesar, Gurgaon, Tel: +91-124-480-3200
Haryana-122 050, India Fax: +91-124-480-3201
DENSO PRODUCTS AND SERVICES AMERICAS, INC. Sales:
Address: 3900 Via Oro Avenue, Long Beach, California 90810, U.S.A. Tel: +310-834-8652
Fax: +310-952-7406
Service:
Tel: +310-834-8652
Fax: +310-952-7599
DENSO SALES CANADA, INC. Sales & Service:
Address: 195 Brunel Road, Mississauga, Ontario, Canada, L4Z 1X3 Tel: +1-905-890-0890
Fax: +1-905-890-8474

DENSO INTERNATIONAL KOREA CORPORATION Sales:

Address: 131, Seonggogae-ro, Uiwang-si, Gyeonggi-do, Korea Tel: +82-31-340-1786
437-120 Fax:+82-31-8033-7211
TAS CORPORATION Sales & Service:
Address: 248-2 Shimoshiota Narumi-cho, Midori-ku, Nagoya, Aichi, Tel: +81-52-621-3277
458-0801, JAPAN Fax: +81-52-621-3288

- 11 -
Regulatory Information to user

MODEL : DN-VIM-003

1.

2. EMC and Radio Regulation in U.S.A.

Model with Bluetooth, Model without Bluetooth
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to
operate the equipment.

NOTICE: This device has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the device is operated in a
commercial environment.
This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.

NOTE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Model with Bluetooth

CAUTION: Radio Frequency Radiation Exposure
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65. This device has very low levels of RF energy that it
deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed
and operated keeping the radiator at least 20 cm or more away from persons body (excluding extremities: hands, wrists,
feet and ankles).

Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

3. EMC in KOREA
Model without Bluetooth
:
:Diagnostic Tester (DN-VIM-003)
:DENSO CORPORATION/
:KCC-REM-DKR-DN-VIM-003
:Refer to serial number on product.
For more information please contact the office that is listed in the instruction manual.

T02228Z
4. EMC and Radio Regulation in CANADA
Model with Bluetooth
NOTE
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the
IC radio frequency (RF) Exposure rules.
This device has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation
(MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from
persons body (excluding extremities: hands, wrists, feet and ankles).

Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Lopration est soumise aux deux conditions suivantes:

(1) Ce priphrique ne peut tre la cause dinterfrence, et
(2) Ce priphrique se doit daccepter toute(s) interfrence(s), y compris celle(s) susceptible(s) de provoquer des
oprations indsirables dans le cadre de son fonctionnement.
Cet quipement est en conformit avec les limites dexposition aux rayonnements IC prcdemment nonces dans un
environnement non contrl et rpond aux rgles dexposition aux radiofrquences (RF) IC dfinies par RSS-102. Parce
quil bnficie de trs faibles niveaux dnergie RF, cet quipement a t jug conforme sans quil soit ncessaire de
procder une valuation de lexposition permissive maximale (MPE).
Toutefois, il est recommand que cet quipement soit install et opr en prenant soin que le radiateur soit une distance
minimum de 20 cm de toute personne se trouvant dans sa priphrie ( lexclusion des extrmits corporelles suivantes:
mains et poignets et, pieds et chevilles).

Co-implantation: Cet metteur ne doit pas tre co-implant ou exploit conjointement avec une autre antenne ou metteur.

5. EMC and Radio Directive in EU, EFTA and other countries applying CE marking
Model with Bluetooth, Model without Bluetooth
2004/108/EC
Harmonized Standards applied EN 55011 This product falls under group 1 and class A
EN 61000-6-2
Model with Bluetooth
1999/5/EC
Hereby, DENSO CORPORATION, declares that this DN-VIM-003 is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
This device (DN-VIM-003) is including the 2.4GHz wireless transceiver (Bluetooth) that communicate with Personal
Computer.

Manufacturer
Name DENSO CORPORATION
Address 1-1 Showa-cho, Kariya-shi, Aichi-ken, 448-8661 Japan

Importer
Name DENSO EUROPE B.V.
Address Hogeweyselaan 165, 1382 JL Weesp, the Netherlands
Section Sales & Service
Tel +31-294-493-493
Fax +31-294-417-122

T02718Z


T02782Z
6. Radio Regulation in MALAYSIA
Model with Bluetooth
Model name : DN-VIM-003
Manufacturer : DENSO CORPORATION

7. Radio Regulation in INDONESIA

Model with Bluetooth

33991/SDPPI/2014
3886

T02773Z
 


      

3E +J &G &U  3%% 3%'(

 h     

      

     h h
*%7 
h *%7 


 
 


T02774Z
 Instruction Manual

1st Ed. October, 2010

10th Ed. March, 2016