PolyLacticAcid PDF

11
Poly(Lactic Acid)-Based Biomaterials:

Synthesis, Modification and Applications
Lin Xiao1,2, Bo Wang1,2, Guang Yang*1,2 and Mario Gauthier3
1College of Life Science and Technology, Huazhong University of Science and Technology,
2National Engineering Research Center for Nano-Medicine,
Huazhong University of Science and Technology,

3Department of Chemistry, University of Waterloo,
1,2China
3Canada
1. Introduction
Social and economic development has driven considerable scientific and engineering efforts
on the discovery, development, and utilization of polymers. Widespread reliance in
everyday life on conventional polymeric materials such as polyolefins has resulted in
serious pollution which cannot be resolved in a straightforward fashion. Sustainable
development and a green economy both require brand new materials which can avoid the
occurrence of these problems.
Poly(lactic acid) (PLA), an aliphatic polyester, has outstanding advantages over other
polymers, and may thus be part of the solution. As early as the 1970s, PLA products have
been approved by the US Food and Drug Administration (FDA) for direct contact with
biological fluids. Four of its most attractive advantages are renewability, biocompatibility,
processability, and energy saving (Rasal, 2010). First of all, PLA is derived from renewable
and degradable resources such as corn and rice, which can help alleviate the energy crisis as
well as reduce the dependence on fossil fuels of our society; PLA and its degradation
products, namely H2O and CO2, are neither toxic nor carcinogenic to the human body, hence
making it an excellent material for biomedical applications including sutures, clips, and
drug delivery systems (DDS). Furthermore, PLA can be processed by film casting, extrusion,
blow molding, and fiber spinning due to its greater thermal processability in comparison to
other biomaterials such as poly(ethylene glycol) (PEG), poly(hydroxyalkanoates) (PHAs),
and poly( -caprolactone) (PCL) (Rhim et al., 2006). These thermal properties contribute to
the application of PLA in industry in fields such as textiles and food packaging. Last but not
least, PLA production consumes 25-55% less fossil energy than petroleum-based polymers.
Cargill Dow has even targeted a reduction in fossil energy consumption by more than 90%
as compared to any of the petroleum-based polymers for the near future, which will surely
also lead to significant reductions in air and water pollutant emissions. It is also noteworthy
that the total amount of water required for PLA production is competitive with the best
performing petroleum-based polymers. This energy-saving feature perfectly caters to the
*
Corresponding author
www.intechopen.com
248 Biomedical Science, Engineering and Technology
new concept of low-carbon economy which emerged recently in response to the global
warming and energy crisis concerns, and makes investment in PLA a necessary and wise
strategy in the future (Vink et al., 2003). Fig. 1 shows the cycle of PLA in nature.
Fig. 1. The cycle of PLA in nature.

While PLA can be considered an eco-friendly biomaterial with excellent properties, it also
has many obvious drawbacks when confronted with requirements for certain applications:
1) Its degradation rate through hydrolysis of the backbone ester groups is too slow. This
process sometimes takes several years, which can impede its biomedical and food packaging
applications (Bergsma et al., 1995). 2) PLA is very brittle, with less than 10% elongation at
break, thus it is not suitable for demanding mechanical performance applications unless it is
suitably modified (Rasal & Hirt, 2009). 3) PLA is strongly hydrophobic and can elicit an
inflammatory response from the tissues of living hosts, because of its low affinity with cells
when it is used as a tissue engineering material. 4) Another limitation of PLA towards its
wider industrial application is its limited gas barrier properties which prevent its complete
access to industrial sectors such as packaging (Singh et al., 2003). Considering the
disadvantages of PLA stated above and its high cost (another shortcoming of that material),
it is not surprising that PLA has not received the attention it deserves. Nevertheless,
researchers have examined different methods for the bulk or surface modification of PLA,
the introduction of other components, or the control of its surface energy, surface charge
and surface roughness, depending on the requirements of specific applications.
Previous reviews have examined different aspects of PLA chemistry and engineering. Thus
Maharana et al. (Maharana et al., 2009) presented a review on the melt-solid
polycondensation of lactic acid (LA). Gupta et al. (Gupta et al., 2007) presented an overview
of the production of PLA fibers by various methods, along with correlations between the
www.intechopen.com
Poly(Lactic Acid)-Based Biomaterials: Synthesis, Modification and Applications 249
structure and the properties of the fibers. Butterwick et al. (Butterwick et al., 2009) discussed
the applications of PLA in Europe and the United States with respect to practitioner
experiences and techniques to optimize the outcomes. Rasal et al. (Rasal et al., 2010)
examined the chemical modification of PLA, while Graupner et al. (Graupner et al., 2009)
assessed the production and the mechanical characteristics of composites prepared from
PLA and renewable raw materials including cotton, hemp, kenaf, and man-made cellulose
fibres (Lyocell) by compression molding.
In this chapter we will underline novel ideas or technologies introduced over the last 5-10
years, emphasizing some ambitious work which, even though it appears less successful than
other mature methods, introduces concepts that may prove extremely positive in the near
future. We will also attempt to foretell developmental trends on the basis of social demands
and the progress achieved so far. More traditional topics including the synthesis,
modification, and applications of PLA in biomedical field will be introduced mainly to
provide a more comprehensive picture of PLA as a biomaterial.
2. Physical and chemical properties of PLA

L-lactic acid and D-lactic acid, the two isomers of lactic acid, are shown in Scheme 1. Pure L-
lactic acid or D-lactic acid, or mixtures of both components are needed for the synthesis of
PLA.
O O
OH OH
C C
C OH C OH
H CH3 H3C H
L-Lactic acid D-Lactic acid
Scheme 1. The stereoisomers of lactic acid.
The homopolymer of LA is a white powder at room temperature with Tg and Tm values of
about 55C and 175C, respectively. High molecular weight PLA is a colorless, glossy, rigid
thermoplastic material with properties similar to polystyrene. The two isomers of LA can
produce four distinct materials: Poly(D-lactic acid) (PDLA), a crystalline material with a
regular chain structure; poly(L-lactic acid) (PLLA), which is hemicrystalline, and likewise
with a regular chain structure; poly(D,L-lactic acid) (PDLLA) which is amorphous; and
meso-PLA, obtained by the polymerization of meso-lactide. PDLA, PLLA and PDLLA are
soluble in common solvents including benzene, chloroform, dioxane, etc. and degrade by
simple hydrolysis of the ester bond even in the absence of a hydrolase. PLA has a
degradation half-life in the environment ranging from 6 months to 2 years, depending on
the size and shape of the article, its isomer ratio, and the temperature. The tensile properties
of PLA can vary widely depending on whether it is annealed or oriented, or its degree of
crystallinity (Garlotta et al., 2001). Some of the physical and chemical properties of PLA are
summarized in Table 1.
www.intechopen.com
Properties PDLA PLLA PDLLA

Solubility All are soluble in benzene, chloroform, acetonitrile,
tetrahydrofuran (THF), dioxane etc., but insoluble in
ethanol, methanol, and aliphatic hydrocarbons
Crystalline structure Crystalline Hemicrystalline Amorphous
Melting temperature (Tm)/ C ~180 ~180 Variable
Glass transition temperature 50-60 55-60 Variable
(Tg)/ C
Decomposition temperature/C ~200 ~200 185-200
Elongation at break/ (%) 20-30 20-30 Variable
Breaking strength/ (g/d) 4.0-5.0 5.0-6.0 Variable
Half-life in 37C normal saline 4-6 months 4-6 months 2-3 months
Table 1. Selected physical and chemical properties of PLA.
3. Synthesis of PLA
Two main synthetic methods are used to obtain PLA: Direct polycondensation (including
solution polycondensation and melt polycondensation), and ring-opening polymerization
(ROP).
3.1 Direct polymerization

Since the LA monomer has both OH and COOH groups, necessary for polymerization,
the reaction can take place directly by self-condensation (Scheme 2):
CH 3 CH 3
polymerization
n HO C COOH H O C COO H + (n - 1) H 2O
H catalyst H n
Lactic acid Poly(lactic acid)

Scheme 2. Direct polymerization.
Direct polymerization includes solution and melt polycondensation, depending on whether
a solvent is used in the reaction to dissolve the PLA or not.
3.1.1 Solution polycondensation

In this case an organic solvent capable of dissolving the PLA without interfering with the
reaction is added, and the mixture is refluxed with removal of the water generated in the
polycondensation process, which is beneficial to achieve a high molecular weight. Many
procedures yield PLA with a weight-average molecular weight (Mw) of over 200,000 by this
method (Ohta et al., 1995; Ichikawa et al., 1995). This approach was developed by Carothers
and is still used by Mitsui Chemicals. The resultant polymer can be coupled with
isocyanates, epoxides or peroxides to produce a range of molecular weights (Lunt et al.,
www.intechopen.com
1998). The reaction proceeds smoothly, however solution polymerization suffers from
certain disadvantages such as being susceptible to impurities from the solvent and various
side reactions including racemization and trans-esterification. It also consumes large
volumes of organic solvents, which are potential pollutants to the environment.
Under optimized conditions, Ajioka et al. obtained PLA with Mw > 300,000 by this method
(Ajioka et al., 1995). Characterization data have shown that the glass transition temperatures
(Tg) of PLA and polylactide synthesized by the conventional lactide process are essentially
identical (Tg = 58C and 59 C, respectively), but PLA has a lower melting point (Tm = 163
C) than polylactide (Tm = 178C). The mechanical properties of the two polymers are also
very similar.
3.1.2 Melt polycondensation

In contrast to solution polycondensation, the melt polycondensation of monomers can
proceed without any organic solvent, but only if the temperature of the reaction remains
above the Tm of the polymer (Gao et al., 2002). Moon et al. discovered that high Mw PLLA
[Mw 100,000] could be produced in this way in a relatively short reaction time ( 15 h)
(Moon et al., 2000). This method can lower the cost of the synthesis significantly due to the
simplified procedure, but major problems still need to be solved before it can be applied
industrially because of its sensitivity to reaction conditions (Maharana et al., 2009). Thus
Moon et al. worked to develop a melt/solid polycondensation technique using a binary
catalyst system (tin dichloride hydrate and p-toluenesulfonic acid) (Moon et al., 2001).
Simply put, thermal oligocondensates of LA were first subjected to melt polycondensation
to obtain a melt polycondensate, which was then subjected to solid state polycondensation
at 105C. As a consequence, the molecular weight of the PLA was as high as 600,000 after a
short reaction time under optimized conditions.
In summary, these one-step polymerization processes are relatively economical and easy to
control, but they are equilibrium reactions affected by numerous parameters such as the
temperature, the reaction time, catalysts, pressure, and so on. These factors can strongly
influence the molecular weight of the products obtained. Besides, the water generated in
this process can cause high molecular weight PLA to break down at high reaction
temperatures. Thus the polymer resulting from these reactions usually has an
unsatisfactorily low molecular weight. Attention must be paid to three aspects of the
reaction to obtain a high molecular weight, namely controlling the reaction kinetics,
removing the water formed, and preventing the degradation of the PLA chains.
3.2 Ring-opening polymerization

Considering the drawbacks of direct polymerization, PLA is typically synthesized by ring-
opening polymerization (ROP) (Scheme 3), an important and effective method to
manufacture high molecular weight PLA. This reaction requires strict purity of the lactide
monomer, obtained by dimerization of the lactic acid monomer. PLA is obtained by using a
catalyst with the monomer under vacuum or an inert atmosphere. By controlling the
residence time and the temperatures in combination with the catalyst type and
concentration, it is possible to control the ratio and sequence of D- and L-lactic acid (LA)
units in the final polymer (Lunt et al., 1998). The polymerization mechanism involved can be
ionic, coordination, or free-radical, depending on type of catalyst employed (Penczek et al.,
www.intechopen.com
2000). Most of the researchers are now exploring new and effective catalysts. Khn et al.
(Khn et al., 2003) first reported that the ROP of D,L-lactide could be catalyzed by
bis(trimethyl triazacyclohexane) praseodymium triflate [(Me3TAC)2 Pr(OTf)3] (Cat), while
Pr(OTf)3 by itself had a poor catalytic activity. Cat was found to catalyze the polymerization
of D,L-lactide in various solvents (THF, dichloromethane, ethyl acetate, and toluene)
without any additional reagents. The optimal polymer yield (95%) and molecular weight
(18,000) were obtained after 18 h at 170C, with a ratio of [LA]:[Cat] = 1000. John et al. (John
et al., 2007) produced one of the few reports on lactide polymerization with a Cu-based
catalyst. ROP of L-lactide catalyzed by {2-[1-(2,6-diethylphenylimino)ethyl]phenoxy}2Cu(II)
yielded the highest Mw (26.3 103) with a monomer conversion of 57%. Two other copper
complexes, {2-[1-(2,6-dimethylphenylimino)ethyl]phenoxy}2Cu(II) and {2-[1-(2-
methylphenylimino)ethyl]phenoxy}2Cu(II), also catalyzed the reaction under solvent-free
melt conditions (160C) but produced polylactides of moderate molecular weights (Mw =
12.0 103 and 15.9 103, respectively).
CH3 H3C O O CH3

cyclization ring-open polymerization
2 HO C COOH O C COO
H -H2O catalyst H n
O O CH3
Lactic acid Lactide Poly(lactic acid)
Scheme 3. Ring-opening polymerization.

Numerous studies have examined the influence of different factors such as the concentration
and type of catalyst, monomer purity, and temperature on the polymerization of lactide.
Special attention has been paid to the catalyst. Currently tin octoate is the most widely used
catalyst for the ring-opening polymerization of lactides, but numerous novel efficient metal-
free catalytic systems are emerging as valuable alternatives (Jrme & Lecomte, 2008). The
heavy metal-based catalysts are indeed very likely to contaminate the product, which
complicates the purification of the PLA obtained and also limits the applications of PLA in
the fields of food packaging and biomedicine. Some of the means developed to solve this
problem will be addressed later.
3.3 New approaches

The inherent disadvantages of the traditional synthetic methodology have led some
researchers to explore solutions such as the development of nontoxic catalysts, unusual
polymerization conditions, or other polymerization pathways (Lassalle & Ferreira, 2008).
To solve the potential pollution problems caused by heavy metal catalysts, many nontoxic
catalysts derived from magnesium (Wu et al., 2005), calcium (Zhong et al., 2003), zinc
(Sarazin et al., 2004), alkali metals (Chisholm et al., 2003), and aluminum (Nomura et al.,
2002) have been developed for the ROP of lactides (Deng et al., 2000; Ejfler et al., 2005). For
example, Chen et al. (Chen et al., 2007) tested a series of -diketiminate zinc complexes as
initiators for the ROP of lactide and they were all highly active, however the Mw attained
was unsatisfactory. It is worth noting that a variety of rare earth derivatives are usually
highly reactive, which entitles them to be very promising initiators for the ROP of lactide
(Agarwal et al., 2000).
www.intechopen.com
With respect to unusual reaction conditions, supercritical CO2 (scCO2) technology has
attracted much attention because this environmentally friendly, chemically inert,
inexpensive, non-toxic, and nonflammable solvent can be substituted for organic solvents
(Nalawade et al., 2006). Yoda et al. (Yoda et al., 2004) thus carried out the synthesis of
PLLA from an L-lactic acid oligomer in scCO2 with dicyclohexyldimethylcarbodiimide
(DCC) as an esterification promoter and 4-dimethylaminopyridine (DMAP) as a catalyst.
PLLA with a number-average molecular weight Mn reaching 13,500 was obtained in 95%
yield after 24 h at 3500 psi and 80C. The molecular weight distribution of the products
was also narrower than for PLLA prepared by meltsolid phase polymerization under
conventional conditions. Not only can scCO2 be used as a medium to synthesize
polymers, but it can also serve in the purification and processing of the polymer micro-
particles obtained (Kang et al., 2008).
The direct polycondensation of lactic acid has been considered to have a promising future
due to its low cost; however it is hard to increase the molecule weight due to the difficulty in
removing the water from the system under these conditions. One way to solve this problem
is a chain-extension method, although the properties of the PLA obtained in this way can be
somewhat affected by the procedure. Simply put, hydroxyl- or carboxyl-terminated low
molecular weight PLA obtained by direct polymerization can be linked together through a
chain extender, which is a bifunctional compound carrying highly reactive functional
groups. Many achievements have been reported in this area, hexamethylene diisocyanate
(HDI) being the most widely used chain extender for hydroxyl-terminated prepolymers
since the work done by Woo and coworkers (Woo et al., 1995). Finding new and satisfactory
chain extenders will remain a major goal in the near future, since HDI is toxic and subject to
side reaction in this process.
In addition, LA-polymerizing enzymes functioning in replacement of metal catalysts
should enable the biosynthesis of PLA, even though it is enormously challenging both in
terms of research and industrial implementation. The best solution could be the
development of a PLA-producing microorganism, but this has not been reported so far.
Taguchi et al. (Taguchi et al. 2008) have nonetheless obtained encouraging results by
developing a recombinant Escherichia coli strain allowing the synthesis of LA-based
polyesters by introducing the gene encoding polyhydroxyalkanoate (PHA) synthase. This
is illustrated in Fig. 2. They thus achieved the one-step biosynthesis of a copolymer with 6
mol% of lactate and 94 mol% of 3-hydroxybutyrate units, having a molecular weight of 1.9
105. This extremely important result represents a milestone towards the biological
synthesis of PLA and confirms that the work is moving in the right direction. At present,
the LA fraction in the copolyesters has been enriched up to 96 mol% (Shozui et al., 2011),
so the synthesis of homopolymers of LA represents a major goal. To that end, the current
microbial cell factory ought to be improved with further evolved LA-polymerizing
enzymes (LPE) and metabolic engineering-based optimization (Taguchi, 2010).
Matsumura et al. (Matsumura et al., 1997) likewise reported the lipase PC-catalyzed
polymerization of cyclic diester-D,L-lactide at a temperature of 80-130C to yield
poly(lactic acid) with molecular masses of up to 12,600. Other novel methods (e.g. metal-
free catalysts, non-catalytic systems) are also under development (Zhong et al., 2003;
Achmad et al., 2009). The advantages and disadvantages of the PLA synthesis methods
mentioned above are summarized in Table 2.
www.intechopen.com
Substitution
Bio-process Chemo-process
Fermentation
Sugar Lactate (LA) LA

Propionyl-CoA
Photosynthesis
transferase
H3C O O
LA-CoA
O O CH3
LA-polymerization Metal
enzyme catalysts
CO2 LA polyester PLA
Degradation
Microbe
Fig. 2. Mechanism for the bio-synthesis of LA polyester. In the bio-process, the LA monomer
is converted into LA-CoA ,which is recognized by the LA-polymerizing enzyme recruited
from microbial PHA synthase (Tajima et al., 2009).
Synthesis methods Advantages Disadvantages

Solution One-step, economical and Impurities, side reactions,
polycondensation easy to control pollution, low molecular weight
PLA
Melt polycondensation High reaction temperature,
sensitivity to reaction
conditions, low molecular
weight PLA
Ring-opening High molecular weight Requires strict purity of the
polymerization PLA lactide monomer, related high
cost
New solutions Efficient, non-toxic, no Under development
(new catalysts, pollution , high molecular
polymerization weight PLA, etc.
conditions, etc)
Biosynthesis One-step, efficient, non- Under development
toxic, no pollution, low
cost, etc.
Table 2. Comparison of PLA synthesis methods.
www.intechopen.com
4. Modification of PLA
The major drawbacks of PLA limiting its applications are its poor chemical modifiability
and mechanical ductility, slow degradation profile, and poor hydrophilicity. In order to be
suitable for specific biomedical applications, the PLA has been modified mainly concerning
two aspects: Bulk properties and surface chemistry. To achieve this, both chemical
modification and physical modification have been tried, involving the incorporation of
functional monomers with different molecular architectures and compositions, the tuning of
crystallinity and processibility via blending and plasticization, etc., which are described in
the following sections.
4.1 Bulk modification

Biomaterials must possess bulk properties, particularly hydrophilic and mechanical
properties, meeting special requirements. Critical factors affecting these characteristics
include chemical additives, composition, and morphological structure. At present
considerable research focuses on a variety of hydrolytic groups, controlling the flexibility
and crystallinity of the molecular chains, and the presence of hydrophilic groups.
4.1.1 Physical modification

Blending, plasticization, and composition variations belong to this category.
Blending
Polymer blending is an effective, simple, and versatile method to develop new materials with
tailored properties without synthesizing new polymers (Peesan et al., 2005). The properties of
different polymers (biodegradable and non-biodegradable) can be combined by blending with
PLA, or even new properties can arise in the products due to interactions between the
components. Biodegradable components blended with PLA include poly(ethylene glycol)
(PEG), poly( -hydroxybutyrate) (PHB), poly( -caprolactone) (PCL), poly(butylene adipate-co-
terephthalate) (PBAT), chitosan, and starch (Sheth et al., 1997). While blends of PLA and non-
biodegradable polymers have not been as extensively studied, low-density polyethylene
(LDPE), poly(vinyl acetate) (PVA), and polypropylene (PP) have been examined. Reddy et al.
(Reddy et al., 2008) found that PLA in blends obtained from five ratios of PLA/PP had
substantially better resistance to biodegradation and hydrolysis, and improved dyeability with
dispersed dyes. However most of these blends are immiscible (phase-separated) and display
poor mechanical properties due to low interfacial adhesion between the polymer phases.
To improve the processing and mechanical properties of PLA without sacrificing its
degradability and biocompatibility, Xu et al. (Xu et al., 2009) blended PLA with a new
degradable thermoplastic derived from konjac glucomannan (TKGM), synthesized by graft
copolymerization of vinyl acetate and methyl acrylate onto konjac glucomannan (KGM).
Dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM) measurements
showed that the PLA/TKGM system was miscible due to specific interactions between PLA
and TKGM. This led to a maximum elongation at break of 520% for the blend (20/80), as
compared to 14% for neat PLA. The impact strength also increased from 11.9 kJ/m2 for neat
PLA to 26.9 kJ/m2 for the 20/80 blend. The synthesis of new polymers, biodegradable or non-
biodegradable, to be compatibly blended with PLA, will represent a major task in the future.
Plasticization
PLA is a glassy polymer with poor elongation at break (typically less than 10%). The
modification of PLA with different biodegradable and non-biodegradable plasticizers,
www.intechopen.com
having a low molecular weight but a high boiling point and a low volatility, has been
explored as a mean to lower the Tg and increase the ductility and softness of PLA. This has
been achieved by varying the molecular weight, the polarity and functional groups of the
plasticizers. Biocompatible molecules such as oligomeric lactic acid, oligomeric citrate ester,
oligomeric PEG, and glycerol are all plasticizers of choice for PLA (Martin & Averous, 2001;
Ljungberg et al., 2005). Ljungberg et al. (Ljungberg & Wessln, 2002) have blended PLA with
five plasticizers (triacetine, tributyl citrate, triethyl citrate, acetyl tributyl citrate, and acetyl
triethyl citrate) and found that triacetine and tributyl citrate were more effective as
plasticizers than the others to obtain a significant decrease in Tg for PLA.
Wang et al. (Wang et al., 2009) found that diisononyl cyclohexane-1,2-dicarboxylate
(DINCH), a new plasticizer obtained by the hydrogenation of the benzene ring of o-
phthalates, had limited compatibility with PLA when compared with tributyl citrate ester
(TBC). PLA samples plasticized with 10 and 20 phr DINCH gave a constant Tg of 50C. They
were stiff materials displaying elevated values of elongation at break (129% and 200%,
respectively) and impact strength (41.1 MPa and 30.1 MPa, respectively). On the other hand,
TBC significantly decreased the Tg and increased the crystallinity of PLA, the PLA/TBC (20
phr TBC) blend being a soft material with a Tg of 24C. Results from thermogravimetric and
thermal analysis also indicated that PLA plasticized with DINCH had good mechanical
properties and excellent water resistance (as reflected in time-dependent weight loss data in
phosphate buffer) and aging resistance (characterized by the mechanical and thermal
properties of specimens exposed to ambient conditions for 4 months).
Composition
Fibers can serve as fillers in the formation of PLA composites processable by compression or
injection molding, to enhance the thermal stability, the hydrolysis resistance, or the
mechanical properties of PLA. Several investigations on PLA composites prepared from
natural and modified cellulose fibers have shown that their mechanical properties scale with
the mass fraction of added fibers (Wan et al., 2001; Mathew et al., 2005). Optimization of the
natural fiber-reinforced PLA composites, in terms of mechanical and other properties, is
critical to minimize their cost, tailor their biodegradability, and broaden their areas of
application. Inorganic fillers can also contribute to property modification. Table 3 provides a
comparison of some of the organic and inorganic materials tested as PLA fillers.
Graupner et al. (Graupner et al., 2009) prepared composites from different types of natural
fibers (cotton, hemp, kenaf) and modified cellulose fibers (Lyocell), with a fiber mass
fraction of 40%, by compression molding. The mechanical properties of these composites are
summarized in Table 4. Tom et al. (Tom et al., 2011) prepared composites from PLA and
acetylated bacterial cellulose by mechanical compounding. The composites displayed
significant increases in both elastic and Young moduli, as well as in tensile strength
(increments of about 100, 40, and 25%, respectively, as compared with neat PLA) at 6% filler
loading. Some surface modifiers can enhance adhesion between the fibers and the PLA
matrix. For example, 3-aminopropyltriethoxysilane (APS) hydrolyzes in water or solvents to
produce silanol groups that are capable of bonding to -OH groups on the kenaf fiber surface
(Huda et al., 2008). The -NH2 groups from APS can also bond with -CO2- sites formed on the
PLA surface by treatment with a sodium hydroxide solution. Thus APS effectively functions
as a coupling agent. Yang et al. (Yang et al., 2011) produced a composite from PLA and
microcrystalline cellulose modified by L-lactic acid. The tensile strength and the elongation
at break of the composite were higher than for neat PLA. The surface modification of the
cellulose substrates was considered a key element of the mechanical reinforcement.
www.intechopen.com
Type Filler Result Reference

Organic Jute Tensile stress and modulus increase with fiber Khondkeret
volume fraction al., 2006
Flax fibers Composite strength about 50% higher than for Oksman et al.,
PP/flax composites 2003
Kenaf fibers Greatly improved crystallization rate, tensile Pan et al., 2007
and storage moduli
Bamboo fibers Increased bending strength and improved Tokoro et al.,
thermal properties 2008
Silkworm silk Good wettability, increased elasticity modulus Cheung et al.,
fibers and ductility 2008
Microcrystalline Poor mechanical properties and adhesion; Mathew et al.,
cellulose increased storage modulus 2005
LA-modified Higher tensile strength and elongation at break Yang et al.,

microcrystalline than neat PLA 2011
cellulose
Acetylated Considerable improvement in thermal and Tom et al.,
bacterial cellulose mechanical properties 2011
Inorganic Calcium Narrow pore size distribution and high tensile Jung et al.,
metaphosphate strength 2005
Calcium carbonate No brittle fracture behavior and comparably Kasuga et al.,
high bending strength 2003
Montmorillonite Good affinity and improved thermal stability Pluta et al.,
of the nanocomposites 2002
HAP Improved elastic modulus and unchanged Kasuga et al.,
bending strength 2001
Carbon nanotubes Dramatic enhancement in thermal and Wu & Liao,
mechanical properties 2007
Nano/Micro-silica Increased tensile strength, thermal stability, Huang et al.,
and hydrolysis resistance 2009
Table 3. Organic and inorganic fillers for the preparation of PLA composites.
Tensile Youngs Elongation at Charpy impact

strength/ modulus/ break/ strength/
(N/mm2) (N/mm2) (%) (kJ/mm2)
Pure PLA sample 30.1 3820.2 0.83 24.4
Cottom-PLA 41.2 4242.3 3.07 28.7
Kenaf-PLA 52.9 7138.6 1.05 9.0
Hemp-PLA 57.5 8064.2 1.24 9.5
Lyocell-PLA 81.8 6783.8 4.09 39.7
Hemp/kenaf-PLA 61.0 7763.8 1.22 11.8
Hemp/Lyocell-PLA 71.5 7034.9 1.65 24.7
Table 4. Mechanical properties of composites and a pure PLA sample (mean values; all the
specimens were tested at 0C; adapted in part from (Graupner et al., 2009).
www.intechopen.com
Kim et al. (Kim et al., 2010) prepared a series of PLA/exfoliated graphite (EG)
nanocomposites and confirmed that the graphite nanoplatelets could be dispersed
homogeneously within the PLA matrix. Thermogravimetric analysis also showed that the
thermal stability of the nanocomposites was improved with incremental amounts of EG up
to 3 wt %. For example, the temperature corresponding to a 3% weight loss for a composite
with 3.0 wt % EG increased by 14 degrees to ~364 C vs. pure PLA. Additionally, the
Youngs modulus of the composites increased with their graphite content and their electrical
resistivity was dramatically lowered. Poly(lactic acid)/hydroxyapatite (PLA/HAP)
composite scaffolds processed by foaming with supercritical CO2 were shown to be
promising for bone replacement, because their mechanical characteristics closely matched
the properties of bone in terms of viscoelasticity and anisotropy (Mathieu et al., 2006).
4.1.2 Chemical modification

The chemical modification of PLA has been achieved mainly through copolymerization and
cross-linking.
Copolymerization
The carboxyl and hydroxyl groups of LA make it possible to copolymerize it with other
monomers through polycondensation with lactone-type monomers such as -caprolactone,
which generally leads to low molecular weight copolymers, or alternately through the ring-
opening copolymerization of lactide with other cyclic monomers including glycolide, -
valerolactone, and trimethylene carbonate, as well as with monomers like ethylene oxide
(EO) to produce high molecular weight copolymers. The hydrophobicity and crystallinity of
the copolymers can be increased for low to moderate comonomer contents. Besides,
poly(ethylene oxide) (PEO) and PEG have been most commonly copolymerized with PLA to
prepare copolymers on account that it is highly biocompatible, hydrophilic and non-toxic,
non-immunogenic and non-antigenic (Metters et al., 2000). Such properties reduce protein
adsorption and enhance resistance to bacterial and animal cell adhesion.
Block copolymers are composed of long sequences (blocks) of the same monomer unit,
covalently bound to sequences of a different type. The blocks can be connected in a variety
of ways. Fig. 3 shows examples of block copolymer structures. Diblock PLA-PEG
copolymers and triblock PLA-PEG-PLA copolymers allow modulation of the
biodegradation rate, the hydrophilicity, and the mechanical properties of the copolymers,
while phase separation can be tailored with PLA-PEG multi-block copolymers of
predetermined block lengths (Wang et al., 2005). Star- and dendrimer-like PLA-PEG
copolymers have also been synthesized to lower the Tg, Tm, and the crystallinity of the
materials (Zhang et al., 2004).
Riley et al. (Riley et al., 2001) prepared a range of PLA-PEG copolymers incorporating a PEG
block of constant molecular weight (Mn = 5,000) and varying PLA segment lengths (Mn =
2,000-110,000) by ROP of D,L-lactide catalyzed by stannous octoate; all the dispersions were
stable under physiological conditions. In 2003, Li and Vert (Li & Vert, 2003) prepared series
of diblock and triblock copolymers by ring-opening polymerization of L(D)-lactide from
mono- and dihydroxyl PEO, using zinc metal as a catalyst under vacuum. The copolymers
were semicrystalline, their composition and molar mass being determining factors affecting
their solubility in water. Fu et al. (Fu et al., 2008) prepared series of LA-based polyurethanes
modified by castor oil with controllable mechanical properties. In this work, hydroxyl-
terminated prepolymers were synthesized by copolymerization of L-LA and 1, 4-butanediol.
www.intechopen.com
(a)
(d)
(b)
(c) (e)
Fig. 3. Schematics of block copolymer structures: (a) diblock; (b) triblock; (c) alternating
multiblock; (d); dendrimer-like copolymer; (e) star-like copolymer.
Cross-linking
Cross-linked PLA structures can be formed either by irradiation or through chemical
reactions. Electron beam and -irradiation have been widely applied to cross-linking PLA in
the presence of small amounts of cross-linking agents such as triallyl isocyanurate (TAIC)
(Quynh et al., 2008; Phong et al., 2010). The thermal stability of PLA-based materials can be
significantly improved in this way (Quynh et al., 2007). Quynh et al. (Quynh et al., 2009)
obtained stereocomplexes by cross-linking blends of PLLA and low molecular weight
PDLA. Alkaline hydrolysis and enzymatic degradation of the stereocomplex could be
controlled by radiation cross-linking, because the alkaline solution as well as proteinase
hardly attacked the cross-linked polymer network. Unfortunately, irradiation equipment is
expensive and the PLA samples must be processed as thin plates to absorb enough energy
from the radiation to initiate cross-linking reactions, which significantly limits its practical
application.
Modified PLA with different gel fractions and cross-linking densities can also be obtained
through chemical reactions between linking agents and the polymer chains without
irradiation (Agrawal et al., 2010). Yang et al. (Yang et al., 2008) thus induced cross-linking
via treatment of the PLA melt with small amounts of TAIC and dicumyl peroxide (DCP).
The results obtained for samples with different gel fractions and cross-link densities showed
that the cross-linking of PLA was initiated at low contents of either TAIC or DCP. The
crystallinity of cross-linked PLA samples obtained with 0.5 wt% TAIC and 0.5 wt% DCP
decreased from 32% for pure PLA to 24%. Significant increases in tensile modulus from 1.7
GPa to 1.9 GPa, and in tensile strength from 66 GPa to 75 GPa were also observed, and the
thermal degradation initiation and completion temperatures were both increased relatively
to neat PLA. Additional advantages of this method are that it requires neither extra
purification steps nor specialized equipment, since the reaction is carried out in the molten
state with only small amounts of cross-linking agent. It is thus economically very
advantageous over irradiation, which requires expensive equipment. An increase in
brittleness was nevertheless observed following the formation of highly cross-linked
structures, which remains a problem to be solved.
www.intechopen.com
4.2 Surface modification

The surface properties of materials play a key role in determining their applications. The
presence of specific surface chemical functionalities, hydrophilicity, roughness, surface
energy, and topography is crucial for biomedical applications of PLA and its interactions
with biomacromolecules. Pure PLA causes a mild inflammatory response if it is implanted
into human tissues. It is therefore important to design biomaterials with the required surface
properties. The different surface modification strategies examined include physical
methods, including surface coating, entrapment and plasma treatment, and chemical
methods. Both types of approaches are reviewed.
4.2.1 Physical methods

Surface coating
This is one of the simplest surface modification methods and has been applied to various
polymers, but particularly to PLA nanoparticles used for drug delivery. For instance, PEG
coating delayed the phagocytosis of PLA nanoparticles and prolonged the circulation time
of the nanoparticles in vivo (Gref et al., 1994). Unfortunately the PEG-coated PLA
nanoparticles cannot provide specific targeting, which influences their delivery efficiency.
One of the most promising alternatives to PEG in this respect is the use of polysaccharides.
These materials provide steric protection to the nanoparticles against non-specific
interactions with proteins and thereby insure particle stability in the blood circulation
system (Ma et al., 2008). Additionally, ligands to achieve active targeting can be conjugated
on the surface of these nanoparticles, because many reactive groups are available on the
polysaccharides and their derivatives (Gu et al., 2007). Another option is coating of the
surface with extracellular matrix (ECM) proteins such as fibronectin, laminin, vitronectin,
and collagen, which are conducive to cell adhesion and can greatly improve
biocompatibility as well (Lin et al., 2010).
Innovative work was accomplished by Cronin et al. (Cronin et al., 2004), who tested a PLLA
fiber scaffold as a substrate for the differentiation of human skeletal muscle cells. Cell
attachment (the number of cells attached to the films counted along the center, from one
edge to the opposite edge of the film within the field of view) increased significantly on
PLLA films coated with ECM gel, fibronectin, or laminin as compared to uncoated or
gelatin-coated PLLA films. Myoblasts were able to differentiate into multinucleated
myofibers on the ECM gel-coated PLLA fibers and expressed muscle markers such as
myosin and -actinin, as demonstrated by western blot and oligonucleotide microarray
analysis.
Entrapment
The entrapment of modifying species (e.g. PEG, alginate, gelatin, etc.) can be achieved
through reversible swelling of the PLA surface as illustrated in Fig. 4. This is a simple yet
effective method for surface modification requiring no specific functional groups in the
polymer chains, as the modifying molecules accumulate merely on the surface of the
material without modifying its bulk properties (Lu et al., 2009). Additionally, entrapment
can be used to generate different morphologies and thicknesses of 3D scaffolds, which
cannot be achieved by other surface modification methods. Finally, entrapment allows the
modification of the surface in a controlled fashion because various parameters (e.g. solvent
ratio, gelatin concentration, immersion time, and chemical cross-linking) can be varied to
tailor the process (Zhu et al., 2003).
www.intechopen.com
Fig. 4. Schematic illustration of entrapment process.

PEG (Mw = 18,500) and poly(L-lysine) (PLL) (Mw = 29,300) have been trapped on PLA
surfaces using 2,2,2-trifluoroethanol (TFE)/water as solvent/nonsolvent mixtures (Quirk et
al., 2002). A new entrapment process has also been reported by Liu et al. (Liu et al., 2005),
through chemical cross-linking of gelatin with 1-ethyl-3-(3-dimethylaminopropyl)
carbodiimide (EDC) HCl and N-hydroxysuccinimide (NHS) (97%) in {2-[N-morpholino]
ethanesulfonic acid} (MES) hydrate buffer, after the pretreated PLLA films were immersed
in the gelatin solution for a set time. Results in comparison to the control scaffolds have
shown that the surface hydrophilicity increased with the amount of entrapped gelatin and
that cell attachment and proliferation, the deposition of collagen fibers, and other cell
excretion (extracellular matrix, etc.) were also significantly improved.
Plasma treatment
Tests with plasma treatment were initiated in the 1960s and have been since then widely
utilized to improve the hydrophilicity and cell affinity of PLA surfaces. The obvious
advantages of plasma treatment as compared to other surface modification methods include
its ability to control the surface structure, energy and charge, and to uniformly modify the
surface without impacting bulk properties (Chu et al., 2002). Functional groups such as
NH2, COOH, and OH, which are apt to form covalent bonds with other materials for
further modification, are most frequently introduced by plasma treatment (Favia et al.,
1998).
Liu et al. thus investigated the influence of the main operation parameters, namely the
plasma power, the treatment duration (number of treatment cycles) and the electrode gap
on a dielectric barrier discharge (DBD) plasma treatment of PLA films in terms of changes in
surface wettability and chemistry (Liu et al., 2004). They further developed equations
relating the surface properties (water contact angle and oxygen enrichment, as observed by
XPS analysis) to these operational parameters. It was determined that the magnitude of the
electrode gap played a dominant role in the treatment of PLA, and the observed wettability
improvements were attributed to changes in both surface chemistry and microstructure.
Chaiwong and coworkers (Chaiwong et al., 2010) investigated the influence of SF6 plasma
on the hydrophobicity and barrier properties of PLA. It was found that the SF6 plasma
enhanced the hydrophilicity and increased the water absorption time of PLA two-fold.
Plasma treatment did not have any significant influence on the water vapor permeability of
PLA, however, since the bulk structure controlling the transport properties are unaffected
by the treatment. Other types of plasmas such as oxygen, helium, and nitrogen plasmas
have also been investigated (Hirotsu et al., 2002).
www.intechopen.com
While plasma treatment has been successfully applied to improving PLA wettability and
cell affinity, its main disadvantage is that surface rearrangements caused by thermally
activated macromolecular motions, to minimize its interfacial energy, can also influence the
surface modification. Moreover, the potential influence of plasma on the degradation of PLA
cannot be ignored.
4.2.2 Chemical modification

PLA does not carry reactive side-chain functional groups. Consequently, the first step of
chemical modification is typically a simple surface hydrolysis (with an alkali) or an
aminolysis treatment. The hydrophilic COOH and OH or reactive NH2 groups
introduced by cleavage of the ester bonds can be used to bind bioactive molecules such as
arginine-glycine-aspartic acid (RGD)-containing peptides, chitosan (CS), arginine and lysine,
PEG, collagen, and so on to regulate cell adhesion or protein adsorption.
The synthetic RGD-containing peptides could be immobilized on PLA after treatment by
hydrolysis or aminolysis (Stupack et al., 2001). Materials prepared by this method provide
suitable recognition sites for cell adhesion receptors and biodegradation rates, making them
suitable for various applications in fields such as tissue engineering and implant technology.
It has also been determined that RGD-conjugated poly(lactic acid-co-lysine)(arginine-
glycine-aspartic acid) nanoparticles (PLA-PLL-RGD NP) are non-toxic and bind more
efficiently to human umbilical vein endothelial cells (HUVECs) as compared to bare PLA-
PLL NP in vitro. Targeted imaging results obtained in vivo showed that PLA-PLL-RGD can
selectively bind to BACP-37 breast cancer cells. Lieb et al. also demonstrated largely
increased cell densities and cell proliferation on surfaces modified with RGD-anchored
monoaminated poly(ethylene glycol)-block-poly(D,L-lactic acid) (H2N-PEG-PLA), mediated
through RGDintegrin interactions (Lieb et al., 2005).
Chitosan (CS) is a biopolymer displaying good biocompatibility, non-toxicity and
biodegradability, produced by the alkaline N-deacetylation of chitin. The immobilization of
this polymer on PLA has been accomplished by coating the surface with chitosan, modified
with the photosensitive hetero-bifunctional cross-linking reagent 4-azidobenzoic acid, and
irradiation with ultraviolet light to photolyze the azide groups and covalently link the two
polymers (Zhu et al., 2002). The -OH and -NH2 groups of chitosan provide further
opportunities to introduce a wide range of functional groups on the surface. Thus CS
molecules immobilized on PLA were modified with a heparin (Hp) solution to form a
polyelectrolyte complex on the surface, which inhibited platelet adhesion and activation,
and enhanced cell adhesion.
4.3 Outlook of PLA surface modification

The surface attributes of PLA can be tailored to enhance its hydrophilicity and
biocompatiblity through various methods. Unfortunately, all these established methods
for surface modification are inherently flawed to some extent. For example, a single
plasma treatment can merely improve cell adhesion but cannot accelerate cell growth;
non-covalent attachment of a functional material onto a PLA surface is not stable and
permanent. An excellent method suggested to solve the second issue is the use of 1,6-
hexanediamine for surface aminolysis, followed by conjugation with biocompatible
macromolecules such as gelatin, chitosan, or collagen (Zhu et al., 2004). Hong et al. have
www.intechopen.com
shown that chondrocyte cells could attach, proliferate, and spread on PLA microspheres
coated with collagen in the same way as described above, in particular those having high
collagen contents (Hong et al., 2005). It appears that the surface modification of PLA
would be best achieved with a combination of distinct approaches, to benefit from the
advantages of all the methods. Polysaccharide polyelectrolyte multilayers, including
chitosan and dextran sulfate-stabilized silver nano-sized colloids developed by Yu et al.
(Yu et al., 2007), were successfully deposited on an aminolyzed PLA membrane in a layer-
by-layer self-assembly manner. This seemingly easy process resulted in significant
improvements in hydrophilicity, antibacterial activity, hemocompatibility, and
cytocompatibility for the PLA membrane, thanks to the different attributes of NH3+
(positive charge), chitosan (biocompatibility), and silver nanoparticles (antibacterial
activity). The radiation-induced methods are emerging as powerful surface modification
techniques, particularly when relying on PLA photoactivation to create reactive groups or
moieties useful to graft specific chemical functionalities. The irradiation of PLA with UV
(ozone can be generated from molecular oxygen irradiated with UV in this process), for
example, is known to increase fiber adhesion to high surface energy components due to
the introduction of photo-oxidized polar groups on the surface (Koo & Jang, 2008).
Irradiation followed by grafting has also been used extensively to alter PLA surface
characteristics, mainly due to the advantages it offers, namely a low operation cost, mild
reaction conditions, selectivity to UV light, and the permanent surface chemistry changes
induced (Ma et al., 2000).
5. Applications of PLA in the biomedical field

Due to its bioresorbability and biocompatibility in the human body, PLA has been
employed to manufacture tissue engineering scaffolds, delivery system materials, or
covering membranes, different bioabsorbable medical implants, as well as in dermatology
and cosmetics.
5.1 Tissue engineering

Since the introduction of the concept in 1988, tissue engineering, a technique invented to
reconstruct living tissues by associating the cells with biomaterials that provide a scaffold on
which they can proliferate three-dimensionally and under physiological conditions, has
emerged as a potential alternative to tissue or organ transplantation and has thus attracted
great attention in science, engineering, and medicine. To meet the diverse needs of tissue
engineering, scaffolds made from various materials have been tested in this field. Although
certain metals are somewhat good choices for medical implants due to their superior
mechanical properties, their lack of degradability in a biological environment makes them
disadvantageous for scaffold applications (Liu & Ma, 2004). Inorganic/ceramic materials
such as HAP or calcium phosphates, being studied for mineralized tissue engineering with
good osteoconductivity, are also limited due to poor processability into porous structures
(Ilan & Ladd, 2002). In contrast, polymers have great design flexibility because their
composition and structure can be tailored to meet specific needs (Huang et al., 2007).
Degradable polymers frequently used for tissue engineering applications are linear aliphatic
polyesters such as PGA, PLA, and their copolymers (PLGA), which are fabricated into
www.intechopen.com
scaffolds. These polymers are among the few synthetic polymers approved by the FDA for
human clinical applications. The drawbacks of these polyesters include their hydrophobicity
and lack of functional groups, which limits cell adhesion, an important factor when
constructing polymeric scaffolds. Another drawback is their slow hydrolytic degradation
(Iwata & Doi, 1998).
An ideal scaffold used for tissue engineering should possess the following properties: 1) Be
biocompatible, so that the scaffold can be well integrated into host tissues without resulting
in any immune response; 2) It should be porous with appropriate pore size, size distribution
and mechanical function, to allow cell or tissue growth and the removal of metabolic waste;
3) It must be mechanically able to withstand local stress and maintain the pore structure for
tissue regeneration; 4) Very importantly, the scaffold should be biodegradable (Ma, 2004).
Synthetic scaffolds are considered important components of a successful tissue engineering
strategy (Wang, 2007). Hybrid three dimentional porous scaffolds of synthetic and naturally
derived biodegradable polymers are particularly promising because they combine the
advantages of the two types of materials. They should maintain sufficient mechanical
strength while providing specific cell-surface receptors during the tissue remodeling process
that stimulate both in vitro and in vivo cell growth (Chen et al., 2002). PLA-based hybrid
materials have been successfully tested clinically for that purpose so far, and tests on other
tissues including bladder (Engelhardt et al., 2011), cartilage (John et al., 2003), liver (Lv et al.,
2007), adipose (Mauney et al., 2007), and bone tissues (Mathieu et al., 2006) have also been
reported.
Jiang et al. (Jiang et al., 2010) functionalized chitosan/PLGA by heparin immobilization with
controlled loading efficiency. One of the main benefits of introducing chitosan into PLGA
microspheres is that chitosan imparts functionality due to its reactive amino groups, so that
biomolecules such as heparin could be attached (Jiang et al., 2006). The compressive strength
and modulus remained in the range of human trabecular bone after the heparinization
process. More importantly, heparinized chitosan/PLGA scaffolds with a low heparin
loading (1.71 g/scaffold) showed a stimulatory effect on cell differentiation, as indicated by
enhanced osteocalcin expression as compared with a non-heparinized chitosan/PLGA
scaffold. Based on these results, Jiang et al. (Jiang et al., 2006) continued to evaluate the
novel scaffolds for bone regeneration in vivo. In the rabbit ulnar critical-sized-defect model
created, successful bridging of the critical-sized defect on the sides both adjacent to and
away from the radius occurred using chitosan/PLGA-based scaffolds. However, the
addition of chitosan to PLGA led to somewhat higher inflammation and lower
mineralization than for the PLGA counterpart, which is a major problem that remains to be
solved.
Three-dimensional (3D) electrospun fibrous scaffolds have been suggested as a potential
tissue engineering tool for bone regeneration. Shim et al. (Shim et al., 2010) thus reported a
3D microfibrous PLLA scaffold fabricated using electrospinning techniques with a
subsequent mechanical expansion process. The use of these 3D scaffolds for the proliferation
of osteoblasts was examined. The 3D scaffolds led to a 1.8-fold higher level of osteoblast
proliferation than generally achieved for electrospun 2D nanofibrous membranes. In vivo
results further showed that 3D electrospun microfibrous matrices provided a favorable
substrate for cell infiltration and bone formation after 2 and 4 weeks when using a rabbit
calvarial defect model.
www.intechopen.com
3D printing technology has rapidly expanded in the tissue engineering field since it was
first developed at the Massachusetts Institute of Technology. Ge et al. (Ge et al., 2009)
developed 3D-printed poly(lactic acid-co-glycolic acid) (PLGA) scaffolds which could
support the proliferation and osteogenic differentiation of osteoblasts. Based on their in
vitro study, they also evaluated PLGA scaffolds for bone regeneration within a rabbit
model (Ge et al., 2009). In both the intra-periosteum and the iliac bone defect models, the
implanted scaffolds facilitated new bone tissue formation and maturation over a time
period of 24 weeks.
The current clinical use of PLA-based scaffolds nevertheless remains very limited (Iwasa et
al., 2009), mainly because of the risk of disease transmission and immune response. This can
be illustrated by taking cartilage tissue engineering as an example. Traditional autologous
chondrocyte implantation (ACI), first introduced by Brittberg et al. in 1994 (Brittberg et al.,
1994), has yielded good clinical results (Bentley et al., 2003). To date, none of the short- or
mid-term clinical and histological results using scaffolds were reported to be better than
ACI. As for the scaffolds, collagen and hyaluronan-based matrices are among the most
popular scaffolds in clinical use nowadays, since they offer substrates which are normally
essential elements in native articular cartilage (Iwasa et al., 2009). Among the very few cases
of scaffolds in clinical use is the copolymer of PGA/PLA (polyglactin, vicryl) and
polydioxanone, which is used for cartilage repair under the trade name of BioSeed-B and
BioSeed-C (Biotissue Technologies AG, Freiburg, Germany).
In summary, tissue engineering is one of the most exciting interdisciplinary fields today and
is growing rapidly with time. The inclusive criteria for studies on scaffolds capable of
clinical application were in vivo or clinical studies and thus certain artificially designed
scaffold features (such as pore size, interpore connectivity, etc.) are necessary for optimal
tissue engineering applications (accelerated tissue regeneration). Suggestions for future
directions include the use of designer scaffolds with in vivo experimentation, and coupling
scaffold design with cell printing to create designer material/biofactor hybrids to optimize
tissue engineering treatments (Hollister, 2005).
5.2 Delivery systems

There has long been a desire to achieve the targeted delivery of bioactive compounds to
areas in the body to maximize therapeutic potential and minimize side-effects. Many types
of particles have been tested as delivery tools for biomedical applications such as liposomes,
solid lipid nanoparticles, and biodegradable polyesters like PLA and PLGA (Torchilin,
2006). With its excellent biocompatibility, biodegradability, mechanical strength, heat
processability, and solubility in organic solvents, PLA can be used to produce dosage forms
such as pellets, microcapsules, microparticles (MP), nanoparticles (NP), etc. MP and NP of
PLA, modified or unmodified, are increasingly investigated for sustained release and
targeted drug, peptide/protein, and RNA/DNA delivery applications because of their small
size enabling their permeation through biological barriers such as the blood-brain barrier
(Roney et al., 2007).
Although PLA-based materials such as PLGA have been FDA-approved and are clinically
available, they lack chemical functionalities to facilitate specific cell interactions.
Furthermore, their potential for the sustained release of hydrophilic molecules (e.g.
proteins) is often limited (Fahmy et al., 2005). Frequent undesired effects include low
www.intechopen.com
encapsulation efficiency and high burst release of the encapsulated biomolecule within the
first few hours or days, which is mainly due to the desorption of surface-associated
hydrophilic molecules having weak interactions with the polymer (Fahmy et al., 2005). To
circumvent these limitations and establish therapeutic efficacy, large doses or site-specific
administration are often required for devices comprised of polyester biomaterials. In an
attempt to address these problems, numerous groups have introduced functional groups
(such as amine functionalities) on these materials, either through direct conjugation or
device fabrication with additives (Betram et al., 2009).
As for drug release from MPs or NPs, it is generally controlled by both drug diffusion and
polymer degradation. To ensure the efficacy of drug delivery, control over the particle
size and particle size distribution is critical, since smaller particles and narrower size
distributions facilitate the design of targeted drug delivery systems. These involve
binding fragments specific to a tumor-associated surface antigen, with a ligand binding to
its corresponding receptor on the tumor cell surface, which can be attached on the surface
of the PLA-based materials. Furthermore, polymers that display a physicochemical
response to changes in their environment are being intensively explored as potential drug
and gene delivery systems. The use of stimuli-responsive nanocarriers offers an attractive
opportunity for targeted delivery, in which the delivery system becomes an active
participant rather than a passive vehicle. The advantage of stimuli-responsive
nanocarriers becomes obvious when the stimuli are unique to disease pathology, allowing
the nanocarrier to respond specifically to the pathological characteristics. For instance, in
solid tumors, the extracellular pH decreases significantly from 7.4 (the pH value under
normal physiological conditions) to about 6.5 (Vaupel et al., 1989; Haag, 2004). In
addition, the pH ranges from 4.5 in lysosomes to about 8.0 in mitochondria. Given these
pH shifts, therapeutic compounds with a pKa between 5.0 and 8.0 are able to exhibit
dramatic changes in physicochemical properties (Ganta et al., 2008). Another option is
thermo-sensitive polymeric micelles, containing a hydrophobic core and a thermo-
sensitive shell, the later changing from a hydrophilic nature at body temperature to a
collapsed hydrophobic polymer at a hyperthermic condition of 42C (Na et al., 2006).
Investigations concerned with this theme include responses induced by chemical
substances, changes in temperature (Tyagi et al., 2004) or pH (Sethuraman & Bae, 2007),
electric signals (Sawahata et al., 1990) or other environmental conditions (Qiu & Park,
2001).
The use of nucleic acids as therapeutic agents for genetic diseases has been extensively
studied (Torchilin, 2008). However, a major limitation of this technique lies in the low
delivery efficiency of the therapeutic DNA to the diseased site. To address this issue, various
strategies have been explored including vectors engineered from viruses (Brun et al., 2008)
and PLGA in NP formulations. PLGA NP have shown particular promise in improving the
delivery efficacy (Kocbek et al., 2007). Besides, the physical characteristics of the
nanoparticles can be manipulated to escape the degradative endosomal lumen, resulting in
cytosolic localization. To develop novel administration paths, hybrid versions of research
have been conducted on this subject, yet the results are mostly based on animal models or in
vitro results, making it difficult to draw final conclusions. From clinical trials, substantial
obstacles to their use, such as immunogenicity and inflammatory potential, have also been
demonstrated (Nafee et al., 2007). Therefore, there is still a long way to go before real clinical
applications come through.
www.intechopen.com
Some examples of delivery systems incorporating PLA are provided in Table 5 and in Fig. 5
(Chen et al., 2007; Sethuraman & Bae, 2007). Sethuraman et al. (Sethuraman & Bae, 2007)
developed a novel drug delivery system for acidic tumors consisting of two components: 1)
A polymeric micelle with a hydrophobic core of PLLA and a hydrophilic shell of PEG
conjugated to TAT (a cell-penetrating peptide in HIV), and 2) a highly pH-sensitive
copolymer of poly(methacryloyl sulfadimethoxine) (PSD) and PEG (PSD-b-PEG). The final
carrier, which was able to shield the micelles and expose them at slightly more acidic tumor
pH levels, was achieved by complexing PSD with the TAT of the micelles. The results
obtained showed significantly higher uptake of TAT micelles at pH 6.6 in comparison with
pH 7.4, and that TAT not only translocated into the cells but it was also traced to the surface
of the nucleus [see Fig. 5].
Fig. 5. Test results for PLA-based drug delivery materials. Fluorescent microscopy images
are shown on top for COS7 cells transfected by plasmid encoding enhanced green
fluorescence protein (EGFP) with different carriers: (A) lipofectamine, (B)
methoxypolyethyleneglycol-PLA-chitosan nanoparticles (MePEG-PLA-CS NP); the
transfection efficiency, as detected by flow cytometry, is higher in (B) than in (A)
(Reproduced with the permission from Chen, J. et al. (2007). Preparation, characterization
and transfection efficiency of cationic PEGylated PLA nanoparticles as gene delivery
systems, Journal of Biotechnology, Vol.130, No.2, pp.107. Copyright (2007) Elsevier) At the
bottom are dual label confocal micrographs for MCF-7 cells incubated with TAT micelles: (a)
Cells stained with fluorescein isothiocyanate (FITC) attached to TAT in the micelles; (b) the
same nuclei as in (a) were stained with TOPRO-3; (c) superimposed images of (a) and (b);
the yellow color shows the localization of TAT within the nuclei (Reproduced with the
permission from Sethuraman, V. A. & Bae, Y. H. (2007). TAT peptide-based micelle system
for potential active targeting of anti-cancer agents to acidic solid tumors. Journal of
Controlled Release, Vol.118, No.2, pp.216. Copyright (2007) Elsevier).
www.intechopen.com
Material Application Results Reference

PLA-PEG Carrier for tetanus Enhanced transport across Vila
particles toxoid the rat nasal mucosa et al., 2005
PEG-PLA NP Conjugated with Increased uptake of the Lf- Hu
lactoferrin (Lf) NP by bEnd.3 cells et al., 2009
PLA-b-Pluronic- Carrier for oral Good control over blood Xiong
b-PLA insulin glucose concentration et al., 2007
PLA NP Carrier for HIV Induced seric and mucosal Aline
p24 proteins antibody production et al., 2009
Surfactant-free Carrier for HIV Elicited strong CTL response Liggins
PLA NP p24 proteins and cytokine release et al., 2004
PLA Carrier for Reduced inflammation of Jie
microspheres paclitaxel arthritis rabbit model et al., 2005
PEO-PLA Carrier for 5-FU Complete drug release Zhang &
copolymers and paclitaxel Feng, 2006
PLA-TPGS Carrier for Initial burst followed by Freitas
copolymers paclitaxel sustained release et al., 2005
PLA Carrier for Initial burst followed by an Chen
microspheres nimesulide exponential decrease et al., 2007
PEGylated PLA Gene delivery Improved transfection Ataman-nal
NP systems activity et al., 2006
PLA-PEG-PLA Carrier for 5-FU Good control over the release Venkatraman
copolymer and paclitaxel et al., 2005
AP-PEG- Drug carrier for Presented high tumor- Wu
PLA/MPEG-PAE cancer therapy specific targeting ability et al., 2010
PLGA/PEI NP Carrier for Effective silencing of the Patil &
luciferase siRNA gene in cells Panyam, 2009
cNGR-PEG-PLA Carrier for DNA Rapid and efficient Liu
NP nanoparticle internalization et al., 2011
DMAB coated Loaded with Significantly improved Fay
PLGA NP plasmid DNA transfection efficiencies et al., 2010
Table 5. Investigations on PLA-based material as drug delivery systems. AP: peptide,
CRKRLDRN; MPEG: methyl ether poly(ethylene glycol); PAE: poly( -amino ester); PEI:
polyethylenimine; cNGR: Cyclic Asn-Gly-Arg; DMAB: dimethyldidodecylammonium
bromide.
In summary, some problems still remain to be tackled for this promising novela
dministration method. A major issue is the presence of surfactants such as SDS or stabilizers
such as PVA in the microparticles, necessary to achieve antigen binding and colloidal
stability. Although present only at low concentrations, the acceptability of such components
in human vaccines depends on the results of extensive and costly toxicological studies.
Biodegradable polymers used for drug delivery to date have mostly been in the form of
injectable microspheres or implant systems requiring complicated fabrication processes with
organic solvents. In such systems, the organic solvents can denature components such as
protein drugs being encapsulated. Besides, these delivery systems have relatively low
transfection efficiencies in vitro as compared with reagents commercialized for cell
transfection. The last problem concerns the lack of test results for these delivery systems
www.intechopen.com
using animal models or in clinical trials, which is of fundamental importance for real
applications in biomedical therapy.
5.3 Other fields

Due to its versatility, PLA has been investigated for membrane applications (e.g. wound
covers), implants and medical devices (fixation rods, plates, pins, screws, sutures, etc.), and
dermatological treatments (e.g. facial lipoatrophy and scar rejuvenation).
With respect to wound treatment, bacterial infections are one of the main factors impacting the
healing process. One of the best approaches to treat wound infections is by the immobilization
of drugs or antibacterial agents within the nanofibers by electrospinning, or the
electrospinning of polymers with intrinsic antibacterial and wound-healing properties. Dozens
of patents have been issued on that topic so far (Ghosh et al., 2007; Robinson et al., 2009). Silver
nanoparticles (nAg) and the natural polysaccharide chitosan (as well as its quaternized
derivatives) are most commonly used as antibacterial agents with a high intrinsic activity
against a broad spectrum of bacteria (Rujitanaroj et al., 2008; Ignatova et al., 2009).
Metals are still the most popular materials for fracture fixation, but their disadvantages
include stress shielding, accumulation in tissues, hypersensitivity, growth restriction, pain,
corrosion, and interference with imaging techniques. Consequently, the focus of research is
increasingly shifted to biomaterials like PLA, which offers satisfactory strength during the
healing of bone tissue and then degrades over time (Mavrogenis et al., 2009). A commercial
product with a proven track record in clinical applications is the VICRYLTM suture material,
based on PGA/PLA copolymers (Mehta et al., 2005). The number of applications of PLA as
fixation rods, plates, pins, screws, sutures, etc. in orthopaedics and dentistry is also
increasing (Raghoebar et al., 2006).
Fig. 6. Applications of PLA in the biomedical field.
www.intechopen.com
In 2004, Sculptra [poly(L-lactic acid)] was approved by the FDA as the first injectable
facial volumizer in the treatment of lipoatrophy due to its significant therapeutic
effectiveness (Burgess & Quiroga, 2005). The lipodystrophy syndrome is associated with the
usage of highly active antiretroviral therapy (HAART) containing protease inhibitors or
nucleoside reverse transcriptase inhibitors for HIV patients. The action mechanism of
Sculptra is via stimulation of the fibroblastic activity with generation of collagen and other
connective tissue fibers. In addition, it acts as dermal matrix adding support by thickening
the dermis (Vleggaar & Bauer, 2004). Moreover, PLA can help improve the appearance of
scars due to acne, surgery, trauma, or suture (Lowe & Beer, 2005, as cited in Beer & Rendon,
2006).
6. Conclusions
Due to the multiple desirable characteristics of PLA including renewability,
biocompatibility, transparency, and thermoplasticity, it is being used or is a potential
candidate for many consumer and biomedical applications (Jamshidian et al., 2010). Ever
increasing environmental concerns associated with conventional polymers derived from
petrochemicals lead to constantly expanding applications for PLA since its discovery in 1932
by Carothers at DuPont.
In previous years, the most negative point of PLA was its higher price as compared with
petrochemical-based polymers. Today, by optimizing the LA and PLA production
processes, and with increasing PLA demand, a reduction in its price can be achieved. The
price of PLA is currently much lower than in previous years. Meanwhile, PLA is mainly
synthesized in the industry by ROP employing tin(II) bis(2-ethylhexanoate) (SnOct2) as a
catalyst, which has been approved as a food additive by the FDA, but the potential toxicity
associated with most tin compounds cannot be ignored for biomedical applications.
Scientists all over the world are now exploring novel, well-defined catalysts with good
biocompatibility, high catalytic activity, low toxicity, and excellent stereoselectivity. This
should remain an everlasting interest area. Finally, the possibility of obtaining 100% bio-
sourced opens the way for PLA to become more independent from petrochemical-based
polymers, free of environmental and health concerns.
However, the major disadvantages of PLA such as its poor ductility, slow degradation rate,
and poor hydrophilicity somewhat limit its applications. The modification of PLA bulk and
surface properties has thus become crucial to increase its applicability. Many of the bulk and
surface modification strategies discussed above have been designed to tune the PLA surface
properties according to the demands of biomedical applications. Unfortunately, all these
established methods for surface modification are somewhat deficient and while they
provide control over the wettability, degradation rate, and functionality, it is still
compulsory to minimize their negative impact on PLA bulk properties. Thus a combined
modification strategy (e.g. irradiation followed by grafting) or a better balance of PLA
surface and bulk properties should be sought. Ideally, with respect to a better balance of
properties and shorter modification times, one-step approaches need to be developed
because it is time-consuming to carry out surface and bulk modifications separately, and the
solvents and reagents involved in multiple modification steps tend to affect PLA properties
significantly.
All these modification strategies aim at tailoring the properties of PLA-based materials for
certain applications. Fortunately, more and more encouraging results have been reported,
www.intechopen.com
but the present conclusions from most of these reports cannot be directly generalized to
truly biomedical applications since most of the experiments were carried out in vitro.
Nevertheless, these findings offer some clues for further improvements. The increasing
number of functional PLA-based polyesters provides the opportunity to study the
relationships between structure and functionality of these polymers such as cell adhesion
and degradability in vitro and in vivo, as well as to develop applications of these materials
for delivery system in the form of micro- and nanoparticles or scaffolds for tissue
engineering. Finally, cancers and acquired or inherited genetic diseases represent one of the
most serious threats to the health of human beings, but no effective therapies are available
so far. It is suggested that the development of effective and ideal tools for drug,
peptide/protein, and RNA/DNA delivery will represent a good alternative in drug
development. It therefore appears that it would be best to focus future research work on the
rational design of novel carriers for biomedical uses and targeted delivery systems.
Obviously, this requires plenty of relevant experiments on animal model and enough
clinical trials before they are widely utilized.
Even though countless studies have focused on the synthesis and the modification of PLA
and remarkable progresses has been achieved over the last two decades, vast opportunities
as well as challenges remain in terms of exploring the characteristics of PLA-based materials
and expanding their domains of applications.
7. Acknowledgement
It was supported by the Natural Science of Hubei Province for Distinguished Young
Scholars (No. 2008CDB279) and the Key Technologies R & D Program of Hubei Province
(20091933), the Fundamental Research Funds for the Central Universities, Huazhong
University of Science and Technology (2010JC016) and the National High Technology
Research and Development Program ("863" Program) of China (No. 2008AA10Z339). The
authors are also grateful to Dr. Wen-bin Zhang from the University of Akron for his
valuable suggestions during the preparation of this manuscript.
8. References
Achmad, F. et al., (2009). Synthesis of polylactic acid by direct polycondensation under
vacuum without catalysts, solvents and initiators. Chemical Engineering Journal,
Vol.151, No.1, (August 2009), pp. 342-350, ISSN 1385-8947
Agrawal, S. K. et al., (2000). Rare earth metal initiated ring-opening polymerization of
lactones. Macromolecular Rapid Communications, Vol.21, No.5, (March 2000), pp. 195-
212, ISSN 1022-1336
Agrawal, S. K. et al., (2010). Energetics of association in poly(lactic acid)-based hydrogels
with crystalline and nanoparticle-polymer junctions. Langmuir, Vol.26, No.22,
(October 2010), pp. 17330-17338, ISSN 0743-7463
Ajioka, M. et al. (1995). The basic properties of poly(lactic acid) produced by the direct
condensation polymerization of lactic acid. Journal of Polymers and the Environment,
Vol.3, No.4, (October 1995), pp. 225-234, ISSN 1566-2543
Aline, F. et al., (2009). Dendritic cells loaded with HIV-1 p24 proteins adsorbed on
surfactant-free anionic PLA nanoparticles induce enhanced cellular immune
www.intechopen.com
responses against HIV-1 after vaccination. Vaccine, Vol.27, No.38, (August 2009),
pp. 5284-5291, ISSN 0264-410X
Ataman-nal, Y. et al., (2006). Surfactant-free anionic PLA nanoparticles coated with HIV-1
p24 protein induced enhanced cellular and humoral immune responses in various
animal models. Journal of Controlled Release, Vol.112, No.2, (May 2006), pp. 175-185,
ISSN 0168-3659
Bentley, G. et al., (2003). A prospective, randomized comparison of autologous chondrocyte
implantation versus mosaicplasty for ostechondral defects of the knee. Journal of
Bone and Joint Surgery-British Volume, Vol.85, No.2, (March 2003), pp. 223-230, ISSN
0301-620X
Bergsma, J. E. et al., (1995). Late degradation tissue response to poly(L-lactide) bone plates
and screws. Biomaterials, Vol.16, No.1, (1995), pp. 25-31, ISSN 0142-9612
Bertram, J. P. et al., (2009). Functionalized poly(lactic-co-glycolic acid) enhances drug
delivery and provides chemical moieties for surface engineering while preserving
biocompatibility. Acta Biomaterialia, Vol.5, No.8, (October 2009), pp. 2860-2871, ISSN
1742-7061
Brittberg, M. et al., (1994). Treatment of deep cartilage defects in the knee with autologous
chondrocyte transplantation. New England Journal of Medicine, Vol.331, No.14,
(October 1994), pp. 889-895, ISSN 0028-4793
Brun, A. et al., (2008). Antigen delivery systems for veterinary vaccine development. Viral-
vector based delivery systems. Vaccine, Vol.26, No.51, (December 2008), pp. 6508-
528, ISSN 0264-410X
Burgess, C. M. & Quiroga, R. M. (2005). Assessment of the safety and efficacy of poly-L-
lactic acid for the treatment of HIV-associated facial lipoatrophy. Journal of the
American Academy of Dermatology, Vol.52, No.2, (February 2005), pp. 233-239, ISSN
0190-9622
Butterwick, K. & Lowe, N. J. (2009) Injectable poly-L-lactic acid for cosmetic enhancement:
Learning from the European experience. Journal of the American Academy of
Dermatology, Vol.61, No.2, (August 2009), pp. 281-293, ISSN 0190-9622
Chaiwong, C. et al., (2010). Effect of plasma treatment on hydrophobicity and barrier
property of polylactic acid. Surface and Coatings Technology, Vol.204, No.18-19, (June
2010), pp. 2933-2939, ISSN 0257-8972
Chen, G.; Ushida, T. & Tateishi, T. (2002). Scaffold design for tissue engineering.
Macromolecular Bioscience, Vol.2, No.2, (February 2002), pp. 67-77, ISSN 1616-5187
Chen, H. Y. et al., (2011). Comparative study of lactide polymerization by zinc alkoxide
complexes with a -diketiminato ligand bearing different substituents. Journal of
Molecular Catalysis A: Chemical, Vol.339, No.1-2, (April 2011), pp. 61-71, ISSN 1381-
1169
Chen, J. et al., (2007). Preparation, characterization and transfection efficiency of cationic
PEGylated PLA nanoparticles as gene delivery systems. Journal of Biotechnology,
Vol.130, No.2, (June 2007), pp. 107-113, ISSN 0168-1656
Cheung, H. Y. et al., (2008) A potential material for tissue engineering: Silkworm silk/PLA
biocomposite. Composites Part B: Engineering, Vol.39, No.6, (September 2008), pp.
1026-1033, ISSN 1359-8368
www.intechopen.com
Chisholm, M. H. et al., (2003). Binolate complexes of lithium, zinc, aluminium, and titanium;
preparations, structures, and studies of lactide polymerization. Dalton Transactions,
No.3, (July 2003), pp. 406-412, ISSN 1477-9226
Chu, P. K. et al., (2002). Plasma-surface modification of biomaterials. Materials Science and
Engineering: R: Reports, Vol.36, No.5-6, (March 2002), pp. 143-206, ISSN 0927-796X
Cronin, E. M. et al., (2004).Protein-coated poly(L-lactic acid) fibers provide a substrate for
differentiation of human skeletal muscle cells. Journal of Biomedical Materials
Research Part A, Vol.69A, No.3, (June 2004), pp. 373-381, ISSN 1549-3296
Deng, X. et al., (2000). Polymerization of lactides and lactones VII. Ring-opening
polymerization of lactide by rare earth phenyl compounds. European Polymer
Journal, Vol.36, No.6, (June 2000), pp. 1151-1156, ISSN 0014-3057
Ejfler, J. et al., (2005). Highly efficient magnesium initiators for lactide polymerization.
Dalton Transactions, No.11, (June 2005), pp. 2047-2050, ISSN 1477-9226
Engelhardt, E. M. et al., (2011). A collagen-poly(lactic acid-co-caprolactone) hybrid scaffold
for bladder tissue regeneration. Biomaterials, Vol.32, No.16, (June 2011), pp. 3969-
3976, ISSN 0142-9612
Fahmy, T. M. et al., (2005). Surface modification of biodegradable polyesters with fatty acid
conjugates for improved drug targeting. Biomaterials, Vol.26, No.28, (October 2005),
pp. 57275736, ISSN 0142-9612
Favia, P. & d'Agostino, R. (1998). Plasma treatments and plasma deposition of polymers for
biomedical applications. Surface and coatings Technology, Vol.98, No.1,
(January1998), pp. 1102-1106, ISSN 0257-8972
Fay, F. et al., (2010). Gene delivery using dimethyldidodecylammonium bromide-coated
PLGA nanoparticles. Biomaterials, Vol.31, No.14, (May 2010), pp. 4214-4222, ISSN
0142-9612
Freitas, M. N. & Marchetti, J. M. (2005). Nimesulide PLA microspheres as a potential
sustained release system for the treatment of inflammatory diseases. International
Journal of Pharmaceutics, Vol.295, No.1-2, (May 2005), pp. 201-211, ISSN 0378-5173
Fu, B. et al., (2008). Preparation of lactic acid based polyurethanes modified by castor oil.
Advanced Materials Research, Vols. 47-50, (June 2008), pp. 1458-1461, ISSN 1022-6680
Ganta, S. et al., (2008). A review of stimuli-responsive nanocarriers for drug and gene
delivery. Journal of Controlled Release, Vol.126, No.3, (March 2008), pp. 187-204, ISSN
0168-3659
Gao, Q. W. et al., (2002). Direct synthesis with melt polycondensation and microstructure
analysis of poly(L-lactic acid-co-glycolic acid). Polymer Journal, Vol.34, No.11,
(November 2002), pp. 786-793, ISSN 0032-3896
Garlotta, D. (2001). A literature review of poly(lactic acid). Journal of Polymers and the
Environment, Vol.9, No.2, (April 2001), pp. 63-84, ISSN 1566-2543
Ge, Z. et al., (2009). Proliferation and differentiation of human osteoblasts within 3D printed
poly-lactic-co-glycolic acid scaffolds. Journal of Biomaterials Applications, Vol.23,
(May 2009), pp.533-547, ISSN 1530-8022
Ge, Z. et al., (2009). Histological evaluation of osteogenesis of 3D-printed poly-lactic-co-
glycolic acid (PLGA) scaffolds in a rabbit model. Biomedical Materials, Vol. 4, No. 2,
(April 2009), 021001, ISSN 1748-6041
Ghosh, D. et al., (2007). Interactive wound cover. US Patent 0,258,958, filed February 12,
2007, issued November 8, 2007
www.intechopen.com
Graupner, N.; Herrmann, A. S. & Mssig, J. (2009). Natural and man-made cellulose fibre-
reinforced poly(lactic acid) (PLA) composites: An overview about mechanical
characteristics and application areas. Composites Part A: Applied Science and
Manufacturing, Vol.40, No.6-7, (July 2009), pp. 810-821, ISSN 1359-835X
Gref, R. et al., (1994). Biodegradable long-circulating polymeric nanospheres. Science,
Vol.263, No.5153, (March1994), pp. 1600-1603, ISSN 0036-8075
Gu, M. et al., (2007). Surface biofunctionalization of PLA nanoparticles through amphiphilic
polysaccharide coating and ligand coupling: Evaluation of biofunctionalization and
drug releasing behavior. Carbohydrate Polymers, Vol.67, No.3, (February 2007), pp.
417-426, ISSN 0144-8617
Gupta, B.; Revagade, N. & Hilborn, J. Poly(lactic acid) fiber: An overview. Progress in polymer
science, Vol.32, No.4, (April 2007), pp. 455-482, ISSN 0079-6700
Haag, R. (2004). Supramolecular drug-delivery systems based on polymeric coreshell
architectures. Angewandte Chemie International Edition, Vol.43, No.3, (January 2004),
pp. 278-282, ISSN 1433-7851
Hirotsu, T. et al., (2002). Plasma surface treatments of melt-extruded sheets of poly(L-lactic
acid). Polymer Engineering and Science, Vol.42, No.2, (February 2002), pp. 299-306,
ISSN 0032-3888
Hollister, S. J. (2005). Porous scaffold design for tissue engineering. Nature Materials, Vol.4,
(July 2005), pp. 518-524, ISSN 1476-1122
Hong, Y. et al., (2005). Collagen-coated polylactide microspheres as chondrocyte
microcarriers. Biomaterials, Vol.26, No.32, (November 2005), pp. 6305-6313, ISSN
0142-9612
Hu, K. et al., (2009). Lactoferrin-conjugated PEG-PLA nanoparticles with improved brain
delivery: In vitro and in vivo evaluations. Journal of Controlled Release, Vol.134, No.1,
(February 2009), pp. 55-61, ISSN 0168-3659
Huang, J. W. et al., (2009), Polylactide/nano and microscale silica composite films. I.
Preparation and characterization. Journal of Applied Polymer Science, Vol.112, No.3,
(May 2009), pp. 1688-1694, ISSN 0021-8995
Huang, L. et al., (2007). Synthesis and characterization of electroactive and biodegradable
ABA block copolymer of polylactide and aniline pentamer. Biomaterials, Vol.28,
No.10, (April 2007), pp. 1741-1751, ISSN 0142-9612
Huda, M. S. et al., (2008). Effect of fiber surface-treatments on the properties of laminated
biocomposites from poly(lactic acid)(PLA) and kenaf fibers. Composites Science and
Technology, Vol.68, No.2, (February 2008), pp. 424-432, ISSN 0266-3538
Ichikawa, F. et al., (1995). Process for preparing polyhydroxycarboxylic acid. US Patent
5,440,008, filed May 19, 1994, issued August 8, 1995
Ignatova, M. et al., (2009). Electrospun non-woven nanofibrous hybrid mats based on
chitosan and PLA for wound-dressing applications. Macromolecular Bioscience,
Vol.9, No.1, (January 2009), pp. 102-111, ISSN 1616-5187
Ilan, D. I. & Ladd, A. L. (2002). Bone graft substitutes. Operative Techniques in Plastic and
Reconstructive Surgery, Vol.9, No.4, (November 2002), pp. 151-160, ISSN 1071-0949
Iwasa, J. et al., (2009). Clinical application of scaffolds for cartilage tissue engineering. Knee
Surgery, Sports Traumatology, Arthroscopy, Vol.17, No.6, (June 2009), pp. 561-577,
ISSN 0942-2056
www.intechopen.com
Iwata, T. & Doi, Y. (1998). Morphology and enzymatic degradation of poly(L-lactic acid)
single crystals. Macromolecules, Vol.31, No.8, (April 1998), pp. 2461-2467, ISSN 0024-
9297
Jamshidian, M. et al., (2010). Poly-lactic acid: Production, applications, nanocomposites, and
release studies. Comprehensive Reviews in Food Science and Food Safety, Vol.9, No.5,
(September 2010), pp. 552-571, ISSN 1541-4337
Jiang, T. et al., (2006). In vitro evaluation of chitosan/poly(lactic acid-glycolic acid) sintered
microsphere scaffolds for bone tissue engineering. Biomaterials, Vol.27, No.28,
(November 2006), pp. 4894-4903, ISSN 0142-9612
Jiang, T. et al., (2010). Functionalization of chitosan/poly(lactic acid-glycolic acid) sintered
microsphere scaffolds via surface heparinization for bone tissue engineering.
Journal of Biomedical Materials Research Part A, Vol.93A, No.3, (June 2010), pp. 1193-
1208, ISSN 1549-3296
Jiang, T. et al., (2010). Chitosan-poly(lactide-co-glycolide) microsphere-based scaffolds for
bone tissue engineering: In vitro degradation and in vivo bone regeneration
studies. Acta Biomaterialia, Vol.6, No.9, (September 2010), pp. 3457-3470, ISSN 1742-
7061
Jie, P. et al.,(2005). Micelle-like nanoparticles of star-branched PEO-PLA copolymers as
chemotherapeutic carrier. Journal of Controlled Release, Vol.110, No.1, (December
2005), pp. 20-33, ISSN 0168-3659
John, A. et al., (2007) Ni (II) and Cu (II) complexes of phenoxy-ketimine ligands: Synthesis,
structures and their utility in bulk ring-opening polymerization (ROP) of L-lactide.
Polyhedron, Vol.26, No.15, (April 2007), pp. 4033-4044, ISSN 0277-5387
Jung, Y. et al., (2005). A poly(lactic acid)/calcium metaphosphate composite for bone tissue
engineering. Biomaterials, Vol.26, No.32, (November 2005), pp. 6314-6322, ISSN
0142-9612
Jrme, C. & Lecomte, P. (2008). Recent advances in the synthesis of aliphatic polyesters by
ring-opening polymerization. Advanced drug delivery reviews, Vol.60, No.9, (June
2008), pp. 1056-1076, ISSN 0169-409X
Kang, Y. et al., (2008). Preparation, characterization and in vitro cytotoxicity of
indomethacin-loaded PLLA/PLGA microparticles using supercritical CO2
technique. European Journal of Pharmaceutics and Biopharmaceutics, Vol.70, No.1,
(September 2008), pp. 85-97, ISSN 0939-6411
Kasuga, T. et al., (2001). Preparation and mechanical properties of polylactic acid composites
containing hydroxyapatite fibers. Biomaterials, Vol.22, No.1, (January 2001), pp. 19-
23, ISSN 0142-9612
Kasuga, T. et al., (2003). Preparation of poly(lactic acid) composites containing calcium
carbonate (vaterite). Biomaterials, Vol.24, No.19, (August 2003), pp. 3247-3253, ISSN
0142-9612
Khondker, O. A. et al., (2006). A novel processing technique for thermoplastic
manufacturing of unidirectional composites reinforced with jute yarns. Composites
Part A: Applied Science and Manufacturing, Vol.37, No.12, (December 2006), pp. 2274-
2284, ISSN 1359-835X
Kim, I. H. & Jeong, Y. G. (2010). Polylactide/exfoliated graphite nanocomposites with
enhanced thermal stability, mechanical modulus, and electrical conductivity.
www.intechopen.com
Journal of Polymer Science Part B: Polymer Physics, Vol.48, No.8, (April 2010), pp. 850-
858, ISSN 0887-6266
Kocbek, P. et al., (2007). Targeting cancer cells using PLGA nanoparticles surface modified
with monoclonal antibody. Journal of Controlled Release, Vol.120, No.1-2, (July 2007),
pp. 18-26, ISSN 0168-3659
Koo, G. H. & Jang, J. (2008). Surface modification of poly(lactic acid) by UV/Ozone
irradiation. Fibers and Polymers, Vol.9, No.6, (December 2008), pp. 674-678, ISSN
1875-0052
Khn, R. D. et al., (2003). Ring-opening polymerization of,-lactide with bis (trimethyl
triazacyclohexane) praseodymium triflate. Catalysis Communications, Vol.4, No.1,
(January 2003), pp. 33-37, ISSN 1566-7367
Lassalle, V. L. & Ferreira M. L. (2008). Lipase-catalyzed synthesis of polylactic acid: An
overview of the experimental aspects. Journal of Chemical Technology and
Biotechnology, Vol.83, No.11 , (October 2008), pp. 1493-1502, ISSN 0268-2575
Li, S. & Vert, M. (2003). Synthesis, characterization, and stereocomplex-induced gelation of
block copolymers prepared by ring-opening polymerization of L (D)-lactide in the
presence of poly(ethylene glycol). Macromolecules, Vol.36, No.21, (September 2003),
pp. 8008-8014, ISSN 0024-9297
Lieb, E. et al., (2005). Mediating specific cell adhesion to low-adhesive diblock copolymers
by instant modification with cyclic RGD peptides. Biomaterials, Vol.26, No.15, (May
2005), pp. 2333-2341, ISSN 0142-9612
Liggins, R. T. et al., (2004). Intra-articular treatment of arthritis with microsphere
formulations of paclitaxel: Biocompatibility and efficacy determinations in rabbits.
Inflammation Research, Vol.53, No.8, (August 2004), pp. 363-372, ISSN 1023-3830
Lin, Y. M. et al., (2010). Tissue engineering of lung: The effect of extracellular matrix on the
differentiation of embryonic stem cells to pneumocytes. Tissue Engineering Part A,
Vol.16, No.5, (April 2010), pp. 1515-1526, ISSN 1937-3341
Liu, C. et al., (2004). Effects of DBD plasma operating parameters on the polymer surface
modification. Surface and Coatings Technology, Vol.185, No.2-3, (July 2004), pp. 311-
320, ISSN 0257-8972
Liu, C. X. et al., (2011). Enhanced gene transfection efficiency in CD13-positive vascular
endothelial cells with targeted poly(lactic acid)-poly(ethylene glycol) nanoparticles
through caveolae-mediated endocytosis. Journal of Controlled Release, (in press),
ISSN 0168-3659
Liu, P. et al., (2010). The research of RGD-conjugated PLA-PLL nanoparticles carriers on
targeted delivery to tumor, Proceedings of Nanoelectronics Conference (INEC), 2010 3rd
International, 978-1-4244-3543-2, Hong Kong, January 2010
Liu, X, & Ma, P. X. (2004). Polymeric scaffolds for bone tissue engineering. Annals of
Biomedical Engineering, Vol.32, No.3, (March 2004), pp. 477-486, ISSN 0090-6964
Liu, X.; Won, Y. & Ma, P. X. (2005). Surface modification of interconnected porous scaffolds.
Journal of Biomedical Materials Research Part A, Vol.74A, No.1, (July 2005), pp. 84-91,
ISSN 1549-3296
Ljungberg, N. & Wessln, B. (2002). The effects of plasticizers on the dynamic mechanical
and thermal properties of poly(lactic acid). Journal of Applied Polymer Science, Vol.86,
No.5, (October 2002), pp. 1227-1234, ISSN 0021-8995
www.intechopen.com
Ljungberg, N.; Colombini, D. & Wessln, B. (2005). Plasticization of poly(lactic acid) with
oligomeric malonate esteramides: Dynamic mechanical and thermal film
properties. Journal of Applied Polymer Science, Vol.96, No.4, (March 2005), pp. 992-
1002, ISSN 0021-8995
Lowe, N. & Beer, K. (2005). A new material in subdermal sculpting, In: Procedures in Cosmetic
Dermatology Series; Soft Tissue Augmentation, Carruthers, J. & Carruthers, A., pp.
143-146, Elsevier Saunders, 1-4160-4214-8, Oxford
Lu, J. W. et al., (2009). Surface engineering of poly(D, Llactic acid) by entrapment of soluble
eggshell membrane protein. Journal of Biomedical Materials Research Part A, Vol.91A,
No.3, (December 2009), pp. 701-707, ISSN 1549-3296
Lunt, J. (1998). Large-scale production, properties and commercial applications of polylactic
acid polymers. Polymer Degradation and Stability, Vol.59, No.1, (January 1998), pp.
145-152, ISSN 0141-3910
Lv, Q. et al., (2007). Preparation and characterization of PLA/fibroin composite and culture
of HepG2 (human hepatocellular liver carcinoma cell line) cells. Composites Science
and Technology, Vol.67, No.14, (June 2007), pp. 3023-3030, ISSN 0266-3538
Ma, H.; Davis, R. H. & Bowman, C. N. (1999). A novel sequential photoinduced living graft
polymerization. Macromolecules, Vol.33, No.2, (January 2000), pp. 331-335, ISSN
0024-9297
Ma, P. X. (2004). Scaffolds for tissue fabrication. Materials Today, Vol.7, No.5, (May 2004), pp.
30-40, ISSN 1369-7021
Ma, W. et al., (2008). Evaluation of blood circulation of polysaccharide surface-decorated
PLA nanoparticles. Carbohydrate Polymers, Vol.72, No.1, (April 2008), pp. 75-81,
ISSN 0144-8617
Maharana, T.; Mohanty, B. & Negi, Y. S. (2009). Melt-solid polycondensation of lactic acid
and its biodegradability. Progress in Polymer Science, (January 2009), Vol.34, No.1,
pp. 99-124, ISSN 0079-6700
Martin, O. & Averous, L. (2001). Poly(lactic acid): Plasticization and properties of
biodegradable multiphase systems. Polymer, Vol.42, No.14, (June 2001), pp. 6209-
6219, ISSN 0032-3861
Mathew, A. P.; Oksman, K. & Sain, M. (2005). Mechanical properties of biodegradable
composites from poly lactic acid (PLA) and microcrystalline cellulose (MCC).
Journal of applied polymer science, Vol.97, No.5, (September 2005), pp. 2014-2025, ISSN
0021-8995
Mathieu, L. M. et al., (2006). Architecture and properties of anisotropic polymer composite
scaffolds for bone tissue engineering. Biomaterials, Vol.27, No.6, (February 2006),
pp. 905-916, ISSN 0142-9612
Matsumoto, K. & Taguchi, S. (2010). Enzymatic and whole-cell synthesis of lactate-
containing polyesters: Toward the complete biological production of polylactate.
Applied microbiology and biotechnology, Vol.85, No.4, (December 2009), pp. 921-932,
ISSN 0175-7598
Matsumura, S.; Mabuchi, K. & Toshima, K. (1997). Lipase-catalyzed ring-opening
polymerization of lactide. Macromolecular Rapid Communications, Vol.18, No.6,
(April 2003), pp. 477-482, ISSN 1022-1336
Mauney, J. R. et al., (2007). Engineering adipose-like tissue in vitro and in vivo utilizing
human bone marrow and adipose-derived mesenchymal stem cells with silk fibroin
www.intechopen.com
3D scaffolds. Biomaterials, Vol.28, No.35, (December 2007), pp. 5280-5290, ISSN

0142-9612
Mavrogenis, A. F. et al., (2009). Early experience with biodegradable implants in pediatric
patients. Clinical Orthopaedics and Related Research, Vol.467, No.6, (June 2009), pp.
1591-1598, ISSN 0009-921X
Mehta, R. et al., (2005). Synthesis of poly(lactic acid): A review. Journal of Macromolecular
Science, Part C: Polymer Reviews, Vol.45, No.4, (October 2005), pp. 325-349, ISSN
1532-1797
Metters, A. T.; Anseth, K. S. & Bowman, C. N. (2000). Fundamental studies of a novel,
biodegradable PEG-b-PLA hydrogel. Polymer, Vol.41, No.11, (May 2000), pp. 3993-
4004, ISSN 0032-3861
Moon, S. I. et al., (2000). Melt polycondensation of L-lactic acid with Sn(II) catalysts
activated by various proton acids: A direct manufacturing route to high molecular
weight Poly(L-lactic acid). Journal of Polymer Science Part A: Polymer Chemistry,
Vol.3, No.89, (May 2000), pp. 1673-1679, ISSN 0887-624X
Moon, S. I. et al., (2001). Synthesis and properties of high-molecular-weight poly(L-lactic
acid) by melt/solid polycondensation under different reaction conditions. High
Performance Polymers, Vol.13, No.2, (June 2001), pp. 189-196, ISSN 0954-0083
Moran, M. J.; Pazzano, D. & Bonassar, L. J. (2003). Characterization of polylactic acid-
polyglycolic acid composites for cartilage tissue engineering. Tissue Engineering,
Vol.9, No.1, (February 2003), pp. 63-70, ISSN 1076-3279
Na, K. et al., (2006). Biodegradable thermo-sensitive nanoparticles from poly(L-lactic
acid)/poly(ethylene glycol) alternating multi-block copolymer for potential anti-
cancer drug carrier. European Journal of Pharmaceutical Sciences, Vol.27, No.23,
(December 2006), pp. 115122, ISSN 0928-0987
Nafee, N. et al., (2007). Chitosan-coated PLGA nanoparticles for DNA/RNA delivery: Effect
of the formulation parameters on complexation and transfection of antisense
oligonucleotides. Nanomedicine, Vol.3, No.3, (September 2007), pp. 173-183, ISSN
1743-5889
Nalawade, S. P.; Picchioni F. & Janssen L. P. B. N. (2006). Supercritical carbon dioxide as a
green solvent for processing polymer melts: Processing aspects and applications.
Progress in Polymer Science, Vol.31, No.1, (January 2006), pp. 19-43, ISSN 0079-6700
Nomura, N. et al., (2002). Stereoselective ring-opening polymerization of racemic lactide
using aluminum-achiral ligand complexes: Exploration of a chain-end control
mechanism. Journal of the American Chemical Society, Vol.124, No.21, (May 2002), pp.
5938-5939, ISSN 0002-7863
Ohta, M.; Obuchi, S. &Yoshida, Y. (1995). Preparation process of polyhydroxycarboxylic
acid. US Patent, 5,444,143, filed December 21, 1993, issued August 22, 1995
Oksman, K.; Skrifvars, M. & Selin J. F.. (2003). Natural fibres as reinforcement in polylactic
acid (PLA) composites. Composites Science and Technology, Vol.63, No.9, (July 2003),
pp. 1317-1324, ISSN 0266-3538
Pan, P. et al., (2007). Crystallization behavior and mechanical properties of bio-based green
composites based on poly(L-lactide) and kenaf fiber. Journal of Applied Polymer
Science, Vol.105, No.3, (Auguest 2007), pp. 1511-1520, ISSN 0021-8995
www.intechopen.com
Patil, Y. & Panyam, J. (2009). Polymeric nanoparticles for siRNA delivery and gene silencing.
International Journal of Pharmaceutics. Vol.367, No.1-2, (February 2009), pp. 195-203,
ISSN 0378-5173
Peesan, M.; Supaphol, P. & Rujiravanit R. (2005). Preparation and characterization of
hexanoyl chitosan/polylactide blend films. Carbohydrate Polymers, Vol.60, No.3,
(March 2005), pp. 343-350, ISSN 0144-8617
Penczek, S. et al., (2000). What we have learned in general from cyclic esters polymerization.
Macromolecular Symposia, Vol.153, No.1, (March 2000), pp. 1-15, ISSN 1022-1360
Phong, L. et al. (2010). Properties and hydrolysis of PLGA and PLLA cross-linked with
electron beam radiation. Polymer Degradation and Stability, Vol.95, No.5, (May 2010),
pp. 771-777, ISSN 0141-3910
Pluta, M. et al., (2002) Polylactide/montmorillonite nanocomposites and microcomposites
prepared by melt blending: Structure and some physical properties. Journal of
Applied Polymer Science, Vol.86, No.6, (November 2002), pp. 1497-1506, ISSN 0021-
8995
Qiu, Y. & Park, K. (2001). Environment-sensitive hydrogels for drug delivery. Advanced Drug
Delivery Reviews, Vol.53, No.3, (December 2001), pp. 321-339
Quirk, R. A. et al., (2000). Surface engineering of poly(lactic acid) by entrapment of
modifying species. Macromolecules, Vol.33, No.2, (January2000), pp. 258-260, ISSN
0024-9297
Quynh, T. M. et al., (2007). Properties of crosslinked polylactides (PLLA & PDLA) by
radiation and its biodegradability. European Polymer Journal, Vol.43, No.5, (May
2007) pp. 1779-1785, ISSN 0014-3057
Quynh T. M. et al., (2008). The radiation crosslinked films based on PLLA/PDLA
stereocomplex after TAIC absorption in supercritical carbon dioxide. Carbohydrate
Polymers, Vol.72, No.4, (June 2008), pp. 673-681, ISSN 0144-8617
Quynh, T. M. et al., (2009). Properties of radiation-induced crosslinking stereocomplexes
derived from poly(L-lactide) and different poly(D-lactide). Polymer Engineering and
Science, Vol.49, No.5, (May 2009), pp. 970-976, ISSN 0032-3888
Raghoebar, G. M. et al., Resorbable screws for fixation of autologous bone grafts. Clinical
Oral Implants Research, Vol.17, No.3, (June 2006), pp. 288-293, ISSN 0905-7161
Rasal, R. M. & Hirt, D. E. (2009). Toughness decrease of PLA-PHBHHx blend films upon
surface-confined photopolymerization. Journal of Biomedical Materials Research Part
A, Vol.88A, No.4, (March 2009), pp. 1079-1086, ISSN 1549-3296
Rasal, R. M.; Janorkar, A. V. & Hirt, D. E. (2010). Poly(lactic acid) modifications. Progress in
Polymer Science, Vol.35, No.3, (March 2010), pp. 338-356, ISSN 0079-6700
Reddy, N.; Nama, D. & Yang, Y. (2008). Polylactic acid/polypropylene polyblend fibers for
better resistance to degradation. Polymer Degradation and Stability, Vol.93, No.1,
(January 2008), pp. 233-241, ISSN 0141-3910
Rhim, J. W. et al., (2006). Effect of the processing methods on the performance of polylactide
films: Thermocompression versus solvent casting. Journal of Applied Polymer Science,
Vol.101, No.6, (September 2006), pp. 3736-3742, ISSN 0021-8995
Riley, T. et al., (2001). Physicochemical evaluation of nanoparticles assembled from
poly(lactic acid)-poly(ethylene glycol) (PLA-PEG) block copolymers as drug
delivery vehicles. Langmuir, Vol.17, No.11, (May 2001), pp. 3168-3174, ISSN 0743-
7463
www.intechopen.com
Robinson, T. M.; Kieswetter, K. & McNulty, A. (2009). System and method for healing a
wound at a tissue site. US Patent 0,216,170, filed February 27, 2009, issued August
27, 2009
Roney, C. et al., (2005). Targeted nanoparticles for drug delivery through the blood-brain
barrier for Alzheimer's disease. Journal of Controlled Release, Vol.108, No.1-2,
(November 2005), pp. 193-214, ISSN 0168-3659
Rujitanaroj, P.; Pimpha, N. & Supaphol, P. (2008). Wound-dressing materials with
antibacterial activity from electrospun gelatin fiber mats containing silver
nanoparticles. Polymer, Vol.49, No.21, (October 2008), pp. 4723-4732, ISSN 0032-
3861
Sarazin, Y.; Schormann, M. & Bochmann, M. (2004). Novel zinc and magnesium alkyl and
amido cations for ring-opening polymerization reactions. Organometallics, Vol.23,
No.13, (May 2004), pp. 3296-3302, ISSN 0276-7333
Sawahata, K. et al., (1990). Electrically controlled drug delivery system using polyelectrolyte
gels. Journal of Controlled Release, Vol.14, No.3, (December 1990), pp. 253-262, ISSN
0168-3659
Sethuraman, V. A. & Bae, Y. H. (2007). TAT peptide-based micelle system for potential
active targeting of anti-cancer agents to acidic solid tumors. Journal of Controlled
Release, Vol.118, No.2, (April 2007), pp. 216-224, ISSN 0168-3659
Sheth, M. et al., (1997) Biodegradable polymer blends of poly(lactic acid) and poly(ethylene
glycol). Journal of Applied Polymer Science, Vol.66, No.8, (November 1997), pp. 1495-
1505, ISSN 0021-8995
Shin, I. K. et al., (2010). Novel three-dimensional scaffolds of poly(L-lactic acid) microfibers
using electrospinning and mechanical expansion: Fabrication and bone
regeneration. Journal of Biomedical Materials Research B: Applied Biomaterials, Vol.95B,
No.1, (October 2010), pp.150-160, ISSN 1552-4981
Singh, R. P. et al., (2003). Biodegradation of poly( -caprolactone)/starch blends and
composites in composting and culture environments: The effect of
compatibilization on the inherent biodegradability of the host polymer.
Carbohydrate Research, Vol.338, No.17, (August 2003), pp. 1759-1769, ISSN 0008-6215
Stupack, D. G. et al. (October 2001). Apoptosis of adherent cells by recruitment of caspase-8
to unligated integrins. The Journal of Cell Biology, Vol.155, No.3, (2001), pp. 459-470,
ISSN 0021-9525
Taguchi, S. et al., (2008). A microbial factory for lactate-based polyesters using a lactate-
polymerizing enzyme. Proceedings of the National Academy of Sciences, Vol.105,
No.45, (November 2008), pp. 17323-17327, ISSN 0027-8424
Taguchi, S. (2010). Current advances in microbial cell factories for lactate-based polyesters
driven by lactate-polymerizing enzymes: Towards the further creation of new LA-
based polyesters. Polymer Degradation and Stability, Vol.95, No.8, (January 2010), pp.
1421-1428, ISSN 0141-3910
Tajima, K. et al., (2009). Chemo-enzymatic synthesis of poly(lactate-co-(3- hydroxybutyrate))
by a lactate-polymerizing enzyme. Macromolecules, Vol.42, No.6, (February 2009),
pp. 1985-1989, ISSN 0024-9297
Tokoro, R. et al., (2008). How to improve mechanical properties of polylactic acid with
bamboo fibers. Journal of Materials Science, Vol.43, No.2, (January 2008), pp. 775-787,
ISSN 0022-2461
www.intechopen.com
Tom, C. L. et al.,(2011). Transparent bionanocomposites with improved properties

prepared from
acetylated bacterial cellulose and poly(lactic acid) through a simple approach. Green
Chemistry, Vol.13, No.2, (February 2011), pp. 419-427, ISSN 1463-9262
Torchilin, V. P. (2006). Multifunctional nanocarriers. Advanced Drug Delivery Reviews, Vol.58,
No.14, (December 2006), pp. 15321555, ISSN 0169-409X
Torchilin, V. P. (2008). Cell penetrating peptide-modified pharmaceutical nanocarriers for
intracellular drug and gene delivery. Biopolymers, Vol.90, No.5, (September 2008),
pp. 604-610, ISSN 0006-3525
Tyagi, P. et al., (2004). Sustained intravesical drug delivery using thermosensitive hydrogel.
Pharmaceutical Research, Vol.21, No.5, (May 2004), pp. 832-837, ISSN 0724-8741
Vaupel, P.; Kallinowski, F. & Okunieff, P. (1989). Blood flow, oxygen and nutrient supply,
and metabolic microenvironment of human tumors: A review. Cancer Research,
Vol.49, No.23, (December 1989), pp. 64496465, ISSN 0008-5472
Venkatraman, S. S. et al., (2005). Micelle-like nanoparticles of PLA-PEG-PLA triblock
copolymer as chemotherapeutic carrier. International Journal of Pharmaceutics,
Vol.298, No.1, (July 2005), pp. 219-232, ISSN 0378-5173
Vila, A. et al., (2005). PLA-PEG particles as nasal protein carriers: The influence of the
particle size. International Journal of Pharmaceutics, Vol.292, No.1-2, (March 2005), pp.
43-52, ISSN 0378-5173
Vink, E. T. H. et al., (2003). Applications of life cycle assessment to NatureWorksTM
polylactide (PLA) production. Polymer Degradation and Stability, Vol.80, No.3,
(2003), pp. 403-419, ISSN 0141-3910
Vleggaar, D. & Bauer, U. (2004). Facial enhancement and the European experience with
Sculptra. Journal of Drugs in Dermatology, Vol.3, No.5, (September-October 2004), pp.
542-547, ISSN 1545-9616
Wan, Y. Z. et al., (2001). Influence of surface treatment of carbon fibers on interfacial
adhesion strength and mechanical properties of PLA-based composites. Journal of
Applied Polymer Science, Vol.80, No., (April 2001), pp. 367-376, ISSN 0021-8995
Wang, M. (2007). Surface modification of biomaterials and tissue engineering scaffolds for
enhanced osteoconductivity, Proceedings of IFMBE, 978-3-540-68016-1, Kuala
Lumpur, Malaysia, December 2006
Wang, R. Y. et al., (2009). Morphology, mechanical properties, and durability of poly(lactic
acid) plasticized with di(isononyl) cyclohexane-1, 2-dicarboxylate. Polymer
Engineering and Science, Vol.49, No.12, (December 2009), pp. 2414-2420, ISSN 0032-
3888
Wang, S.; Cui, W. & Bei, J. (2005). Bulk and surface modifications of polylactide. Analytical
and Bioanalytical Chemistry, Vol.381, No.3, (February 2005), pp. 547-556, ISSN 1618-
2642
Woo, S. I. et al., (1995) Polymerization of aqueous lactic acid to prepare high molecular
weight poly(lactic acid) by chain-extending with hexamethylene diisocyanate.
Polymer Bulletin, Vol.35, No.4, (May1995), pp. 415-421, ISSN 0170-0839
Wu, C. S. & Liao, H.T. (2007). Study on the preparation and characterization of
biodegradable polylactide/multi-walled carbon nanotubes nanocomposites.
Polymer, Vol.48, No.15, (July 2007), pp. 4449-4458, ISSN 0032-3861
www.intechopen.com
Wu, J. C. et al., (2005). Ring-opening polymerization of lactide initiated by magnesium and

zinc alkoxides. Polymer, Vol.46, No.23, (November 2005), pp. 9784-9792, ISSN 0032-
3861
Wu, X. L. et al., (2010). Tumor-targeting peptide conjugated pH-responsive micelles as a
potential drug carrier for cancer therapy. Bioconjugate Chemistry, Vol.21, No.2,
(February 2010), pp. 208-213, ISSN 1043-1802
Xiong, X. Y. et al., (2007). Vesicles from Pluronic/poly(lactic acid) block copolymers as new
carriers for oral insulin delivery. Journal of Controlled Release, Vol.120, No.1-2, (July
2007), pp. 11-17, ISSN 0168-3659
Xu, C. et al., (2009). Preparation and characterization of polylactide/thermoplastic konjac
glucomannan blends. Polymer, Vol.50, No.15, (July 2009), pp. 3698-3705, ISSN 0032-
3861
Yang, G. et al., (2011). Composite from modified biomass fiber and polylactide (PLA) and
the method of preparation. CN Patent 201010510498, filed October 15, 2010, and
issued January 26, 2011
Yang, S. L. et al., (2008) Thermal and mechanical properties of chemical crosslinked
polylactide (PLA). Polymer Testing, Vol.27, No.8, (December 2008), pp. 957-963,
ISSN 0142-9418
Yoda, S.; Bratton, D. & Howdle, S. M. (2004). Direct synthesis of poly(L-lactic acid) in
supercritical carbon dioxide with dicyclohexyldimethylcarbodiimide and 4-
dimethylaminopyridine. Polymer, Vol.45, No.23, (October 2004), p. 7839-7843, ISSN
0032-3861
Yu, D. G.; Lin, W. C. & Yang, M. C. (2007). Surface modification of poly(L-lactic acid)
membrane via layer-by-layer assembly of silver nanoparticle-embedded
polyelectrolyte multilayer. Bioconjugate Chemistry, Vol.18, No.5, (September-
October2007), pp. 1521-1529, ISSN 1043-1802
Zhang, L. et al., (2004). Camptothecin derivative-loaded poly(caprolactone-co-lactide)-b-
PEG-b-poly(caprolactone-co-lactide) nanoparticles and their biodistribution in
mice. Journal of controlled release, Vol.96, No.1, (April 2004), pp. 135-148, ISSN 0168-
3659
Zhang, Z. & Feng, S. S. (2006). Nanoparticles of poly(lactide)/vitamin E TPGS copolymer for
cancer chemotherapy: Synthesis, formulation, characterization and in vitro drug
release. Biomaterials, Vol.27, No.2, (January 2006), pp. 262-270, ISSN 0142-9612
Zhong, Z. et al., (2003). Single-site calcium initiators for the controlled ring-opening
polymerization of lactides and lactones. Polymer Bulletin, Vol.51, No.3, (November
2003), pp. 175-182, ISSN 0170-0839
Zhu, A. et al., (2002). Covalent immobilization of chitosan/heparin complex with a
photosensitive hetero-bifunctional crosslinking reagent on PLA surface.
Biomaterials, Vol.23, No.23, (December 2002), pp. 4657-4665, ISSN 0142-9612
Zhu, H.; Ji, J. & Shen, J. (2002). Surface engineering of poly(DL-lactic acid) by entrapment of
biomacromolecules. Macromolecular Rapid Communications, Vol.23, No.14, (October
2002), pp. 819-823, ISSN 1022-1336
Zhu, Y. et al., Immobilization of biomacromolecules onto aminolyzed poly(L-lactic acid)
toward acceleration of endothelium regeneration. Tissue Engineering, Vol.10, No.1-2,
(January-February 2004), pp. 53-61, ISSN 1076-3279
www.intechopen.com
Biomedical Science, Engineering and Technology
Edited by Prof. Dhanjoo N. Ghista
ISBN 978-953-307-471-9
Hard cover, 902 pages
Publisher InTech
Published online 20, January, 2012
Published in print edition January, 2012
This innovative book integrates the disciplines of biomedical science, biomedical engineering, biotechnology,
physiological engineering, and hospital management technology. Herein, Biomedical science covers topics on
disease pathways, models and treatment mechanisms, and the roles of red palm oil and phytomedicinal plants
in reducing HIV and diabetes complications by enhancing antioxidant activity. Biomedical engineering coves
topics of biomaterials (biodegradable polymers and magnetic nanomaterials), coronary stents, contact lenses,
modelling of flows through tubes of varying cross-section, heart rate variability analysis of diabetic neuropathy,
and EEG analysis in brain function assessment. Biotechnology covers the topics of hydrophobic interaction
chromatography, protein scaffolds engineering, liposomes for construction of vaccines, induced pluripotent
stem cells to fix genetic diseases by regenerative approaches, polymeric drug conjugates for improving the
efficacy of anticancer drugs, and genetic modification of animals for agricultural use. Physiological engineering
deals with mathematical modelling of physiological (cardiac, lung ventilation, glucose regulation) systems and
formulation of indices for medical assessment (such as cardiac contractility, lung disease status, and diabetes
risk). Finally, Hospital management science and technology involves the application of both biomedical
engineering and industrial engineering for cost-effective operation of a hospital.
How to reference
In order to correctly reference this scholarly work, feel free to copy and paste the following:
Lin Xiao, Bo Wang, Guang Yang and Mario Gauthier (2012). Poly(Lactic Acid)-Based Biomaterials: Synthesis,
Modification and Applications, Biomedical Science, Engineering and Technology, Prof. Dhanjoo N. Ghista
(Ed.), ISBN: 978-953-307-471-9, InTech, Available from: http://www.intechopen.com/books/biomedical-
science-engineering-and-technology/poly-lactic-acid-based-biomaterials-synthesis-modification-and-
applications
InTech Europe InTech China

University Campus STeP Ri Unit 405, Office Block, Hotel Equatorial Shanghai
Slavka Krautzeka 83/A No.65, Yan An Road (West), Shanghai, 200040, China
51000 Rijeka, Croatia
Phone: +385 (51) 770 447 Phone: +86-21-62489820
Fax: +385 (51) 686 166 Fax: +86-21-62489821
www.intechopen.com
www.intechopen.com

PolyLacticAcid PDF

Uploaded by

Copyright:

Available Formats

PolyLacticAcid PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PolyLacticAcid PDF

Uploaded by

Copyright:

Available Formats

What are the advantages and disadvantages of PLA?

What are the advantages and disadvantages of PLA?

How can the disadvantages of PLA be addressed?

How can the disadvantages of PLA be addressed?

11

Poly(Lactic Acid)-Based Biomaterials:

Huazhong University of Science and Technology,

Fig. 1. The cycle of PLA in nature.

2. Physical and chemical properties of PLA

Properties PDLA PLLA PDLLA

Table 1. Selected physical and chemical properties of PLA.

3.1 Direct polymerization

Lactic acid Poly(lactic acid)

3.1.1 Solution polycondensation

3.1.2 Melt polycondensation

3.2 Ring-opening polymerization

CH3 H3C O O CH3

Lactic acid Lactide Poly(lactic acid)

Scheme 3. Ring-opening polymerization.

3.3 New approaches

Sugar Lactate (LA) LA

Synthesis methods Advantages Disadvantages

Table 2. Comparison of PLA synthesis methods.

4.1 Bulk modification

4.1.1 Physical modification

Type Filler Result Reference

LA-modified Higher tensile strength and elongation at break Yang et al.,

Tensile Youngs Elongation at Charpy impact

4.1.2 Chemical modification

4.2 Surface modification

4.2.1 Physical methods

Fig. 4. Schematic illustration of entrapment process.

4.2.2 Chemical modification

4.3 Outlook of PLA surface modification

5. Applications of PLA in the biomedical field

5.1 Tissue engineering

5.2 Delivery systems

Material Application Results Reference

5.3 Other fields

Fig. 6. Applications of PLA in the biomedical field.

3D scaffolds. Biomaterials, Vol.28, No.35, (December 2007), pp. 5280-5290, ISSN

Tom, C. L. et al.,(2011). Transparent bionanocomposites with improved properties

Wu, J. C. et al., (2005). Ring-opening polymerization of lactide initiated by magnesium and

InTech Europe InTech China

You might also like