Professional Documents
Culture Documents
Ee6303 Lic Lesson Plan A Sec1
Ee6303 Lic Lesson Plan A Sec1
Days
I II III IV V VI VII VIII
Period
Tuesday
Wednesday
Thursday
Friday
Saturday
EE 6303
LINEAR INTEGRATED
CIRCUITS
EE 6201
Semester II
CIRCUIT THEORY
AC 9. Project Review
Note: Faculty may retain/add/delete the modes of delivery and assessment component
based on their subject
COURSE OUTCOMES:
After successful completion of the course, the students should be able to
Program Specific
Course Program Outcomes
Level Outcomes
Out K3,K5,
of CO K3 K4 K5 K5 A3 A2 A3 A3 A3 A3 A2
Comes K6 PSO-1 PSO-2 PSO-3
PO-1 PO-2 PO-3 PO-4 PO-5 PO-6 PO-7 PO-8 PO-9 PO-10 PO-11 PO-12
C206.1 K2 2 1 - - - - - - - 1 - - - 1 -
C206.2 K2 3 1 2 - - - - - - 1 - - - 1 -
C206.3 K3 3 2 2 - - - - - - 1 - - - 1 -
C206.4 K3 3 2 2 - - - - - - 1 - - - 2 -
C206.5 K3 3 2 2 - - - - - - 1 - - - 1 -
C206.6 K2 3 3 3 - - - - - - 1 - 2 - 1 -
MAPPING OF COURSE OUTCOMES WITH PROGRAM OUTCOMES:
1. Enter correlation levels as defined below:
1. Slight (Low) 2. Moderate (Medium) 3. Substantial (High) If there is no correlation, put -.
ASSESSMENT WEIGHTAGE COMPONENTS:
TARGET % OF STUDENTS
Assessment components
LEVEL % Level 1 Level 2 Level 3
Test 1 (AT 1) 50 50 60 70
Test 2 (AT 2) 50 50 60 70
Test 3 (Model Exam) 50 50 60 70
Assignment 1 70 60 70 80
Assignment 2 70 60 70 80
Unit Test 1 50 50 60 70
Unit Test 2 50 50 60 70
Revision Test 50 50 60 70
University Exam (Grade) C 50 60 70
CO EVALUATION WEIGHTAGE
Note: CO Evaluation Weightage may be retained based on the subject to ease the co attainment
calculation
SYLLABUS
LTPC 3003
OBJECTIVES:
UNIT I IC FABRICATION 9
IC classification, fundamental of monolithic IC technology, epitaxial growth, masking and etching, diffusion
of impurities. Realisation of monolithic ICs and packaging. Fabrication of diodes, capacitance, resistance and
FETs.
Instrumentation amplifier, Log and Antilog Amplifiers, first and second order active filters, , comparators,
multivibrators, waveform generators, clippers, clampers, peak detector, S/H circuit, D/A converter (R- 2R
ladder and weighted resistor types), A/D converters using opamps.
Functional block, characteristics & application circuits with 555 Timer Ic-566 voltage controlled oscillator
Ic; 565-phase lock loop Ic ,Analog multiplier ICs.
IC voltage regulators LM78XX,79XX Fixed voltage regulators - LM317, 723 Variable voltage regulators,
switching regulator- SMPS- LM 380 power amplifier- ICL 8038 function generator IC.
TOTAL : 45 PERIODS
OUTCOMES:
TEXT BOOKS:
T 2. D.Roy Choudhary, Sheil B.Jani, Linear Integrated Circuits, II edition, New Age, 2003.
T3. Ramakant A.Gayakward, Op-amps and Linear Integrated Circuits, IV edition, Pearson
Education, 2003 / PHI. 2000.
REFERENCES:
R 3. Jacob Millman, Christos C.Halkias, Integrated Electronics - Analog and Digital circuits
system,Tata McGraw Hill, 2003.
R4. Robert F.Coughlin, Fredrick F. Driscoll, Op-amp and Linear ICs, PHI Learning, 6th
edition,2012
Online Resources
O1.https://www.youtube.com/watch?v=vK-geBYygXo
O2.http://www.falstad.com/circuit/e-index.html
O3.http://www.youtube.com/watch?v=_vEL_U9rZbg&list=PLE0970E815E238613
O4.http://www.absorblearning.com/advancedphysics/sco.html
O5.http://www.allaboutcircuits.com/vol_3/chpt_8/9.html
COURSE DELIVERY PLAN
UNIT I IC FABRICATION
Proposed Topic Actual Pertaining Highest
S. Lecture Lecture CO(s) Cognitive Mode of Delivery LU Outcomes
Rem
No Level Delivery Resources Students can able to
Period Period
22:07:17
Frequency response of OP- Analyze the Frequency response
5 K3 MD1 T1 of OP-AMP
AMP
22:07:17
6 Basic applications of op-amp K2 MD1 T1 Explain the Basic applications
of op-amp
22:07:17 Inverting and Non-inverting
7 K2 MD1 T1 Design the Inverting and Non-
Amplifiers Inverting Amplifiers
8 24:07:17 V/I & I/V converters K3 MD1 T1 Design V/I & I/V converters
24:07:17 Design summer for given spec
9 Summer K3 MD1 T3
26:07:17 Design differentiator for given
10 Differentiator K3 MD1 T3 spec
29:07:17 First and second order active Design the First and second order
3 K2 MD1 T2 active filters
filters
02:08:17
4 Comparators K3 MD1 T2 Design Comparators
07:08:17
5 Multivibrators K3 MD1&2 T2 State the types of Multivibrators
8 10:08:17 Peak detector, S/H circuit K2 MD1 T2 Discuss Peak detector, S/H circuit
CO4
2 19:08:17 Characteristics of 555 Timer IC K3 MD1 T2
Analyze the Characteristics of 555
Timer IC
23:08:17 Application Circuits with 555 List the application circuits with 555
3 24:08:17 K3 MD1 T2 timer IC
Timer IC
566 Voltage Controlled Explain the 566 voltage controlled
4 26:08:17 K2 MD1 T2 oscillator IC.
Oscillator IC
565-Phase Lock Loop IC. Explain the 565-phase lock loop IC.
5 28:08:17 K2 MD1 T2
Explain thE analog multiplier IC .
6 30:08:17 Analog Multiplier ICs. K3 MD1 T1,O4
2. What are the different methods available for fabricating Integrated resistors. K2
11. What are the advantages of integrated circuits over discrete circuits? K2
17. What is meant by dielectric isolation in I.C Fabrication? Mention its application K2
and Limitations
18. What is the need for buried layer in fabrication of monolithic integrated transistor? K2
20. Compare the performance of n-p-n and p-n-p transistors with respect to IC K2
fabrication
21. What is meant by substantial diffusion? K2
PART B
Questions Blooms
Level
1. Explain the basic Process used in silicon planar technology with neat diagram. K2
2. With respect to BJT based circuit given below, explain the various steps to K2
implement the circuit into a monolithic IC.
3. Describe the epitaxial growth Process.Explain the different types of IC K2
packages.
4.Explain the various steps involved in the fabrication of a typical circuit K2
Give various ways for making integrated resistors. K2
Explain fabrication of n- channel JFET with neat diagram.
5. Briefly explain the various process involved in fabrication monolithic IC K2 CO1
which integrates diode, capacitance and FET.
Explain the various methods used for fabricating IC resistors and compare their K2
performance
Write a note on CMOS technology K2
Write short notes on classification of IC. K2
Explain the functions of all the basic building blocks of an Op-Amp. K2
Explain about MOSFET fabrication K2
Explain about the following Diffusion, Photolithography masking Photo etching. K2
With neat sketches explain the fabrication of diodes capacitors K2
26. Assume that an OP-amp has Ib+=400nA. Ib-=300nA. Find the average bias current
Ib and offset current Ios. K3
27. Determine Vo for the circuit shown in figure. For V1 = 1v, V2 = 3v
K3 CO 2
28. Two voltages +v1 and +v2 are available. Using two operational amplifiers draw a
K3
circuit to compute 5V1-3V2
PART B
Questions Blooms COS
Level
1. Explain the following applications of op-amp
a. Peak detector
b. V/I converter(Floating load & Grounded load) K2
c. Multiplier
d. Scale changer
e. Inverter CO 2
2. Design a second order active high pass filter for a cutoff frequency of 5KHZ K3
3. With neat diagram, explain logarithmic amplifier and antilogarithmic amplifier. K2
4. With a neat diagram, explain the operation of Schmitt trigger. K2
5. Draw the circuit of differentiator and write the expression for the output voltage Vo and K2
also explain practical Differentiator
6. Draw and explain an ideal active op-amp Differentiator circuit. (a)Draw and explain an
ideal active op-amp integrator circuit
(b)Draw the I/O waveforms for integrator
(i) Step i/p signal
(ii) Square wave input signal K3
(iii) Sine wave input signal
(c) Derive the expression for change in output voltage.
(d) List the applications of practical integrator.
(e) Design a practical integrator circuit with a dc gain of 10, to integrate
a square wave of 10 KHz.
7. Draw the circuit diagram and explain the working of an instrumentation amplifier. Mention K2
the specific advantages of three op-amp instrumentation amplifier circuit.
8. Draw the circuit diagram and explain the working of an Adder-Subtractor(or)Draw a circuit K3
to find V0= (V1+V2)-(V3+V4)
9. Explain the operation of clipper and clamper circuit using op-amp. K2
10. Explain Precision Half wave and Full wave Rectifier using op-amp. K2
11. Draw the circuit of a first order and second order butter worth active low pass filter and K2
derive its transfer functions.
12. Design a square wave oscillator for f0 = 1 KHz using 741 op-amp and a DC supply voltage K3
of +/-12V.
13. Design an Op-amp Schmitt trigger with VUT= 2V, VLT= -4V & the output swings b/w K3
+10V. If the i/p is 5 sin wt , plot i/p & o/p waveforms.
14. Explain and design a practical integrator circuit with a dc gain 10,to integrate a
K3
square wave of 10 KHz. CO 2
15. Design and explain an op-amp differentiator that will differentiate an input signal K3
with maximum frequency fmax= 100 Hz.
16. Design and explain first order active high pass filter with fL = 1kHz and pass band
K3
gain of 5.
17. Design an op-amp circuit to give an output voltage V0 =3V1-2V2+5V3, where V1, V2
K3
and V3 are inputs.
18. i) With neat circuit diagrams and mathematical expression explain the operation of
the following op-amp application.
(i) Scale Changer & sign changer
(ii) Voltage follower
ii) Find Vo of the circuit shown in figure
K3
18. i) Draw an adder-subtractor type of circuit with Op-amp to obtain the relation
V0=(V1+V2)-(V3+V4)
ii) Determine the expression for the circuit shown in figure
K3
CO 2
19. Why integrators are preferred in analog computers? Consider a lossy integrator
circuit for the components valuesR1=1K,RF=100K,CF=10nF.Determine the
K3
lower frequency limit of integration and study for the response for Inputs (i) sine
wave (ii) step input (iii) Square input
PART B
Questions Blooms COS
Level
1. Draw and explain the functional block schematic of a NE565 PLL. Derive the expression
K2
for the capture range and lock in range of the PLL.
2. With neat diagrams, explain the operation of four quadrant variable transconductance
K2
multiplier and derive an expression for its output voltage.
3. Explain the working of Analog multiplier using emitter coupled transistor pair K2
4. Discuss the applications of analog multiplier IC. K2
5. Briefly explain Variable Transconductance Amplifier. K2
6. With circuit diagram describe the working of Gilbert multiplier cell. K2
7. Draw the block diagram of PLL and derive an expression for its closed loop transfer
K2
function.
8. With block diagram discuss the principle of operation of NE565 PLL circuit. K2 CO 3
9. With circuit diagram explain the working of NE566 VCO. And also derive the frequency of
K2
oscillation.
10. A PLL is locked on to an incoming signal with a frequency of 1MHz at a phase angle of 50
deg. The VCO signal is at a phase angle of 20 deg. The peak amplitude of the incoming
signal is 0.5V and that of the VCO output signal is 0.7V. K3
11. In the connection diagram of VCO, +V = 12V, R2 = 1.5K,R1=R3=10K and
C1=0.001F, a. Determine the nominal frequency of output waveform b. Compute the
modulation frequency in the output frequency if control voltage is K3
varied between 9.5V and 11.5V.
12. Explain AM detection and FSK modulation using PLL K2
13. How a PLL can be used as frequency synthesizer and FSK demodulator? K2
PART-B
Questions Blooms COS
Level
1. For the 4-bit weighted resistor DAC shown below, R=80 K and RF=8 K.
A 4-bit DAC has VFS = 10V. Determine Vo, given the following binary inputs. a.00012 b.
01002 c. 10002 d. 11112 Assuming that VREF = -5V, determine the LSB size, V0(max) K3
and VFS.
2. The R-2R ladder DAC shown below consists of 10K & 20K resistors, VREF= 2V and CO 4
R1 = 10K. Determine the values required for RF such that VFS = 10V. K3
3. With a neat sketch, explain Flash type ADC. K2
4. With a neat block diagram, explain oversampling ADC. K2
5. Explain (i)Totem pole MOSFET switch 2)CMOS inverter as a switch used in DAC.
Draw the block diagram and explain the working of K2
(i) Charge balancing VFCS (ii) Voltage to Time Converter
6. Explain weighted resistor type and R-2R ladder type DAC, Inverter R-2R Ladder DAC. K2
7. With a neat sketch, explain successive approximation ADC. K2
8. Explain flash type. single type and Dual slope type ADC. K2
9. With a neat sketch, explain dual slope ADC. K2
10. Compare single slope ADC and dual slope ADC. K2
11. For a particular dual slope ADC, t1 is 83.33 ms and the reference voltage is K3
100 mV. Calculate t2 if (i) V1 is 100 mV and (ii) 200 mV
12. Discuss the operation of sample and hold circuit with circuit diagram. K2
CO 4
13. With a neat sketch, explain Flash type ADC. K2
14. Draw the circuit of a four bit R-2R DAc with feedback resistance of 3R for the OPAMP.
Calculate its Vo for the digital input of 0100 if the reference voltage is 2.5v K3
15. For a particular dual slope ADC, t1 is 83.33ms and the reference voltage is 100mV.
Calculate t2 if i)Vi is 100mV and ii) 200mV. K3
16. Find the digital output of an ADC having t1 as 83.33ms and Vr as 100mV for an input
voltage of +100mV. The clock frequency is 12 kHz. K3
PART-B
Questions Blooms COS
Level
1. With a neat diagram, explain IC723 general purpose regulator. K2
2. Write short notes on protective circuits in regulators K2
3. Explain series op-amp regulator with diagram. K2 CO 6
4. Explain fixed voltage series regulator with its characteristics. K2
5. Explain the current limit protection of 723 general purpose regulators. K2
6. Explain step down switching regulator in detail. K2
7. Draw & explain the functional diagram of 555 timers. K2
8. With neat sketches of circuit diagram and waveforms, explain the operation of 555
Timer wired as an astable multivibrator. K2
9. With neat sketches of circuit diagram and waveforms, explain the operation of 555
Timer wired as a monostable multivibrator. K2
10. With neat sketches of circuit diagram and waveforms, explain the operation of 555
Timer wired as a Schmitt trigger. K2
11. Draw the circuit of one-shot using a 555 Timer to provide one time period of 20s? CO 6
If RA = 7.5K, what value of C needed? K3
12. Sketch the circuit of a 555 Timer connected as an astable multivibrator for
operation at 350KHz.Dtermine the value of capacitance C needed using K3
RA=RB=7.5K.
13. Discuss any 2 applications of monostable multivibrator using 555 Timer in detail. K2
14. Draw and explain the circuit of Schmitt trigger using 555 timers. K2
15. Explain functional diagram of 723 general purpose regulators. K2
16.What are the requirements for producing sustained oscillations in feedback
circuits? Discuss any two audio frequency oscillators. K2
17.Discuss in detail the working of a RC phase shift oscillator. K2
CO 5
19.Design Wien Bridge oscillator of 1 KHz frequency. K3
20.Draw and explain the operation of astable multivibrator using op-amp and derive an
expression for its frequency of oscillation. K2
21.State the advantages of IC voltage regulator. Explain the features and internal
structure of general purpose Linear IC723 regulator. Design a regulator using IC 723 to
K4 CO 6
meet the following specifications: V0=5V, I0=100mA, Vin=1520%, Isc=150 mA,
Vsense=0.7V
22.Explain working of monostable multivibrator with necessary waveforms and derive
an expression for its pulse width. K2
23.Draw and explain the operation of a triangular wave generator and derive an
expression for its frequency of oscillation. K2
CO 5
24.Explain the working of a saw tooth waveform generator. Explain the methods to
obtain asymmetric square wave. K2
25.Write detailed notes on the following: (i)Low noise op-amps(ii) Integrated fiber
optic system K2
26.Explain the working of opto couplers. K2
27.Explain in detail voltage to frequency and frequency to voltage converters, Video
amplifier. K2 CO 6
28.What is a switched capacitor filter and its advantages and disadvantages? K2
29. Discuss in detail the working of Isolation amplifier. K2
GUEST LECTURE/SEMINAR/WORKSHOP TO MEET INDUSTRY / PROFESSIONAL
REQUIREMENTS/INDUSTRIAL VISIT
PRINCIPAL