Static Compensator Statcom PDF

Electricity and New Energy
Static Synchronous Compensator

(STATCOM)
Courseware Sample
86371-F0
Order no.: 86371-10
First Edition
Revision level: 07/2016
By the staff of Festo Didactic
Festo Didactic Lte/Ltd, Quebec, Canada 2012

Internet: www.festo-didactic.com
e-mail: did@de.festo.com
Printed in Canada
All rights reserved
ISBN 978-2-89640-572-5 (Printed version)
ISBN 978-2-89747-758-5 (CD-ROM)
Legal Deposit Bibliothque et Archives nationales du Qubec, 2012
Legal Deposit Library and Archives Canada, 2012
The purchaser shall receive a single right of use which is non-exclusive, non-time-limited and limited
geographically to use at the purchaser's site/location as follows.
The purchaser shall be entitled to use the work to train his/her staff at the purchasers site/location and
shall also be entitled to use parts of the copyright material as the basis for the production of his/her own
training documentation for the training of his/her staff at the purchasers site/location with
acknowledgement of source and to make copies for this purpose. In the case of schools/technical
colleges, training centers, and universities, the right of use shall also include use by school and college
students and trainees at the purchasers site/location for teaching purposes.
The right of use shall in all cases exclude the right to publish the copyright material or to make this
available for use on intranet, Internet and LMS platforms and databases such as Moodle, which allow
access by a wide variety of users, including those outside of the purchasers site/location.
Entitlement to other rights relating to reproductions, copies, adaptations, translations, microfilming and
transfer to and storage and processing in electronic systems, no matter whether in whole or in part, shall
require the prior consent of Festo Didactic.
Information in this document is subject to change without notice and does not represent a commitment on
the part of Festo Didactic. The Festo materials described in this document are furnished under a license
agreement or a nondisclosure agreement.
Festo Didactic recognizes product names as trademarks or registered trademarks of their respective
holders.
All other trademarks are the property of their respective owners. Other trademarks and trade names may
be used in this document to refer to either the entity claiming the marks and names or their products.
Festo Didactic disclaims any proprietary interest in trademarks and trade names other than its own.
Safety and Common Symbols
The following safety and common symbols may be used in this manual and on
the equipment:
Symbol Description
DANGER indicates a hazard with a high level of risk which, if not

avoided, will result in death or serious injury.
WARNING indicates a hazard with a medium level of risk which,

if not avoided, could result in death or serious injury.
CAUTION indicates a hazard with a low level of risk which, if not

avoided, could result in minor or moderate injury.
CAUTION used without the Caution, risk of danger sign ,

indicates a hazard with a potentially hazardous situation which,
if not avoided, may result in property damage.
Caution, risk of electric shock
Caution, hot surface
Caution, risk of danger
Caution, lifting hazard
Caution, hand entanglement hazard
Notice, non-ionizing radiation
Direct current
Alternating current
Both direct and alternating current
Three-phase alternating current
Earth (ground) terminal
Festo Didactic 86371-10 III

Safety and Common Symbols
Symbol Description
Protective conductor terminal
Frame or chassis terminal
Equipotentiality
On (supply)
Off (supply)
Equipment protected throughout by double insulation or

reinforced insulation
In position of a bi-stable push control
Out position of a bi-stable push control
IV Festo Didactic 86371-10

Table of Contents
Preface ................................................................................................................. VII
About This Manual ................................................................................................ IX
To the Instructor .................................................................................................. XIII
Introduction Static Synchronous Compensator (STATCOM) ........................ 1

DISCUSSION OF FUNDAMENTALS ....................................................... 1
Voltage compensation of ac transmission lines ...................... 1
Introduction to static synchronous
compensators (STATCOMs) ................................................... 4
Fundamentals of STATCOM operation ................................... 6
Layout of a STATCOM substation ......................................... 10
Comparison between STATCOMs and SVCs ....................... 11
Exercise 1 Voltage Compensation of AC Transmission Lines Using

a STATCOM ................................................................................ 15
DISCUSSION ................................................................................... 15
Voltage compensation of ac transmission lines using a
STATCOM ............................................................................. 15
Automatic voltage compensation........................................... 18
PROCEDURE .................................................................................. 20
Set up and connections ......................................................... 20
Voltage compensation at the receiver end of an
ac transmission line using a STATCOM ................................ 26
Accuracy of the voltage compensation achieved by a
STATCOM when load variations occur .................................... 26
Speed of the voltage compensation achieved by
a STATCOM during load variations.......................................... 29
Exercise 2 Dynamic Power Factor Correction Using a STATCOM .......... 35

DISCUSSION ................................................................................... 35
Power factor correction in industrial applications .................. 35
Using STATCOMs for dynamic power factor correction........ 37
Automatic reactive power control .......................................... 40
PROCEDURE .................................................................................. 42
Set up and connections ......................................................... 42
Operation without dynamic power factor correction .............. 47
Operation with dynamic power factor correction ................... 49
Appendix A Equipment Utilization Chart ...................................................... 59
Appendix B Glossary of New Terms ............................................................. 61
Appendix C Impedance Table for the Load Modules .................................. 63
Festo Didactic 86371-10 V

Table of Contents
Appendix D STATCOM Controller Operation ............................................... 65

Automatic voltage control ...................................................... 65
AC bus line voltage control loop ............................................... 67
DC bus voltage control loop ..................................................... 68
Automatic reactive power control .......................................... 68
Reactive power control loop ..................................................... 71
DC bus voltage control loop ..................................................... 72
Index of New Terms ............................................................................................. 73

Bibliography ......................................................................................................... 75
VI Festo Didactic 86371-10

Preface
The production of energy using renewable natural resources such as wind,
sunlight, rain, tides, geothermal heat, etc., has gained much importance in recent
years as it is an effective means of reducing greenhouse gas (GHG) emissions.
The need for innovative technologies to make the grid smarter has recently
emerged as a major trend, as the increase in electrical power demand observed
worldwide makes it harder for the actual grid in many countries to keep up with
demand. Furthermore, electric vehicles (from bicycles to cars) are developed and
marketed with more and more success in many countries all over the world.
To answer the increasingly diversified needs for training in the wide field of
electrical energy, the Electric Power Technology Training Program was
developed as a modular study program for technical institutes, colleges, and
universities. The program is shown below as a flow chart, with each box in the
flow chart representing a course.
The Electric Power Technology Training Program.
Festo Didactic 86371-10 VII

Preface
The program starts with a variety of courses providing in-depth coverage of basic
topics related to the field of electrical energy such as ac and dc power circuits,
power transformers, rotating machines, ac power transmission lines, and power
electronics. The program then builds on the knowledge gained by the student
through these basic courses to provide training in more advanced subjects such
as home energy production from renewable resources (wind and sunlight), large-
scale electricity production from hydropower, large-scale electricity production
from wind power (doubly-fed induction generator [DFIG], synchronous generator,
and asynchronous generator technologies), smart-grid technologies (SVC,
STATCOM, HVDC transmission, etc.), storage of electrical energy in batteries,
and drive systems for small electric vehicles and cars.
We invite readers of this manual to send us their tips, feedback, and

suggestions for improving the book.
Please send these to did@de.festo.com.

The authors and Festo Didactic look forward to your comments.
VIII Festo Didactic 86371-10

About This Manual
Static synchronous compensators (STATCOMs) are part of the flexible
alternating current transmission systems (FACTS) device family. Their primary
purpose is to supply a fast-acting, precise, and adjustable amount of reactive
power to the ac power system to which they are connected. STATCOMs achieve
this by adjusting the magnitude and polarity (phase) of the reactive component of
the current flowing through their ac side. This enables STATCOMs to control the
amount and direction of flow of the reactive power exchanged with the ac power
system.
STATCOMs can be used for voltage compensation at the receiver end of

ac transmission lines, replacing or supplementing banks of shunt inductors.
When used for this purpose, STATCOMs offer a number of advantages over
banks of shunt inductors, such as much tighter control of the voltage
compensation at the receiver end of the ac transmission line and increased line
stability during load variations.
STATCOMs are also commonly used for dynamic power factor correction
(i.e., dynamic reactive power compensation) in industrial plants operating with
large random peaks of reactive power demand. STATCOMs increase the power
factor of the plant, minimize the voltage fluctuations at the plant input (which
prevents damage to the equipment), and reduce the plants operating costs.
This course, Static Synchronous Compensators (STATCOMs), teaches the basic

concepts of voltage compensation in ac transmission lines and power factor
correction in large industrial plants using STATCOMs. Students are introduced to
the operation of STATCOMs, and their different components. They also learn
how a STATCOM achieves automatic voltage control and automatic reactive
power control. Finally, the theory presented in the manual is verified by
performing circuit measurements and calculations.
Safety considerations
Safety symbols that may be used in this manual and on the equipment are listed
in the Safety Symbols table at the beginning of the manual.
Safety procedures related to the tasks that you will be asked to perform are
indicated in each exercise.
Make sure that you are wearing appropriate protective equipment when
performing the tasks. You should never perform a task if you have any reason to
think that a manipulation could be dangerous for you or your teammates.
Festo Didactic 86371-10 IX

About This Manual
Prerequisite
As a prerequisite to this course, you should have read the following manuals:
DC Power Circuits, part number 86350, Lead-Acid Batteries, part number 86351,
Solar Power, part number 86352, Introduction to Wind Power, part
number 86353, DC Power Electronics, part number 86356, Single-Phase
AC Power Circuits, part number 86358, Single-Phase AC Power Electronics, part
number 86359, Single-Phase Power Transformers, part number 86377,
High-Frequency Power Transformers, part number 86378, Three-Phase
AC Power Circuits, part number 86360, Three-Phase Transformer Banks, part
number 86379, Home Energy Production, part number 86361, Three-Phase
PWM Rectifier/Inverter, part number 86366, and AC Transmission Lines, part
number 20521.
Figure 1. STATCOM substation and close-up view of the converter valves (photo courtesy
of ABB).
Systems of units
Units are expressed using the International System of Units (SI) followed by units
expressed in the U.S. customary system of units (between parentheses).
X Festo Didactic 86371-10

About This Manual
Figure 2. Voltage-source converter (VSC) devices such as STATCOMs are used in offshore
wind farms to ensure that the quality of the power produced by the wind farm is optimal. The
above picture shows the Lillgrund wind farm in Sweden ( Siemens AG 2012, all rights
reserved).
Festo Didactic 86371-10 XI

To the Instructor
You will find in this Instructor Guide all the elements included in the Student
Manual together with the answers to all questions, results of measurements,
graphs, explanations, suggestions, and, in some cases, instructions to help you
guide the students through their learning process. All the information that applies
to you is placed between markers and appears in red.
Accuracy of measurements
The numerical results of the hands-on exercises may differ from one student to
another. For this reason, the results and answers given in this manual should be
considered as a guide. Students who correctly performed the exercises should
expect to demonstrate the principles involved and make observations and
measurements similar to those given as answers.
Equipment installation
In order for students to be able to perform the exercises in the Student Manual,
the Electric Power Technology Training Equipment must have been properly
installed, according to the instructions given in the user guide Electric Power
Technology Training Equipment.
Festo Didactic 86371-10 XIII

Sample Exercise
Extracted from
the Student Manual
and the Instructor Guide
Exercise 1
Voltage Compensation of AC Transmission Lines Using a

STATCOM
EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with the operating
principles of STATCOMs used for voltage compensation of ac transmission lines.
You will know how a STATCOM controller designed for automatic voltage control
compensates the voltage across the ac power system to which the STATCOM is
connected.
DISCUSSION OUTLINE The Discussion of this exercise covers the following points:
Voltage compensation of ac transmission lines using a STATCOM

Automatic voltage compensation
DISCUSSION Voltage compensation of ac transmission lines using a STATCOM
In the Introduction of this manual, you learned that there is overvoltage at the
receiver end of an ac transmission line when little or no load is applied to it. You
also learned that a significant voltage variation occurs at the receiver end of an
ac transmission line whenever the load varies. Such voltage variations are
unacceptable in ac power networks. This is due to the fact that many electrical
devices such as motors, relays, and lighting equipment work properly only under
stable voltage conditions (i.e., close to the voltage for which they are rated).
One way to achieve coarse compensation of voltage variations across an ac

transmission line is to add substations containing switched shunt inductors along
the line. This has the effect of dividing the ac transmission line into many
segments of shorter length. Each substation serves the purpose of compensating
voltage variations across the ac transmission line (i.e., maintaining the voltage
approximately constant across each segment of the ac transmission line).
Figure 17 shows a typical ac transmission line used to transfer large amounts of

electrical power over a long distance from a power generating station to the
distribution network (which, in turn, distributes the electrical power to
consumers).
Festo Didactic 86371-10 15

Exercise 1 Voltage Compensation of AC Transmission Lines Using a STATCOM Discussion
Switched shunt-inductor
in substations
Segment Segment Segment

of line
Sender end (to power generating station)
of line of line
A B C
Receier end (to distribution network)

STATCOM
Figure 17. Typical ac transmission line used to transfer large amounts of electrical power over
a long distance from a power generating station to the distribution network.
As Figure 17 shows, the ac transmission line is divided into three segments of

equal length by two substations (substations A and B) containing switched shunt
inductors used for voltage compensation. The voltage at each of these two
substations is compensated by switching shunt inductors in and out to maintain
the voltage along the ac transmission line as close as possible to the nominal
value of the ac power network voltage. As mentioned in the Introduction of this
manual, switched shunt-inductors in substations have certain drawbacks, such
as the difficulty of coordinating all substations and perfectly compensating the
voltage across each segment of the ac transmission line. However, since
substations A and B are located along the ac transmission line, and thus, do not
directly supply power to consumers, it is not necessary for the voltage at these
substations to be perfectly compensated.
At the end of the third segment (i.e., the receiver end) of the ac transmission line
in Figure 17, the voltage at the corresponding substation (substation C) is
compensated using switched shunt inductors (for coarse compensation) and a
STATCOM. A STATCOM offers numerous advantages over switched shunt
inductors, most notably, a tight and fast compensation of the voltage across the
line. Since the receiver-end substation (substation C in Figure 17) is located at
the end of the ac transmission line, it is important that the voltage at this
substation be compensated as perfectly as possible before distributing electrical
power to consumers. Consequently, it is common to use switched shunt
inductors in conjunction with a STATCOM at the receiver-end substation of an
ac transmission line.
Due to its ability to perform fast and accurate compensation of the voltage at the
receiver end of an ac transmission line, a STATCOM can perfectly compensate
for remaining voltage fluctuations across the line (these fluctuations occur
because compensation with switched shunt inductors is rarely perfect) as well as
for voltage fluctuations caused by variations of the load (i.e., rapid variations of
the electrical power demand of the consumers).
16 Festo Didactic 86371-10

Instead of using a STATCOM, several inductors with different values of

inductance could be used to achieve proper voltage compensation at the receiver
end of an ac transmission line. However, this solution would be as costly as a
STATCOM, if not costlier, and would provide a response time slower than that of
a STATCOM.
It is possible to replace all switched shunt inductors in the substations of the

ac transmission line of Figure 17 with STATCOMs to further increase the
effectiveness of voltage compensation. However, even though STATCOMs are
more efficient than switched shunt inductors in every aspect, it is not common
practice to systematically replace all switched shunt inductors with STATCOMs.
This is primarily because a STATCOM is much more costly (about six times more
expensive) than a bank of switched shunt inductors of comparable power rating.
Since the use of switched shunt inductors to compensate voltage along
ac transmission lines already gives acceptable results, replacing all switched
shunt inductors along these lines with STATCOMs is usually not worth the cost.
Figure 18. STATCOM substations can be used for fast-acting, precise, and adjustable voltage
compensation of ac transmission lines ( Copyright 2012 Guc Kalitesi).

Automatic voltage compensation
When a STATCOM is used for compensating the voltage across an ac power

system (typically ac transmission lines), the voltage across the STATCOM is
regulated using a voltage control loop implemented in the STATCOM controller.
This controller monitors the voltage across the STATCOM side of the step-down
transformer, the current flowing through the STATCOM side of the step-down
transformer, and the voltage across the dc side of the STATCOM (see
Figure 19). Using the measured values, the STATCOM controller determines the
switching signals to be applied to the three-phase bridge in order to ensure that
the line voltages measured across the STATCOM side of the step-down
transformer are equal to the ac bus line voltage command (the value of this
command being set so that the resulting voltage across the STATCOM is at the
required value). The switching signals applied to the three-phase bridge by the
STATCOM controller also ensure that the voltage measured across the dc side
of the STATCOM is equal to the dc bus voltage command. The block diagram of
a STATCOM designed for voltage compensation (i.e., automatic voltage control)
is shown in Figure 19.
AC transmission
line
Line Three-phase Three-phase

inductors filter bridge Load
STATCOM
controller
(automatic voltage
control)
DC bus AC bus line

voltage voltage
command command
( ) ( )
Figure 19. Block diagram of a STATCOM designed for voltage compensation.
a It is assumed that the ac transmission line in the block diagram of Figure 19 is

voltage compensated using switched shunt inductors. However, for the sake of
simplicity, the switched shunt inductors and the capacitors normally included in
the equivalent circuit of an ac transmission line have been omitted in the block
diagram of Figure 19.

As Figure 19 shows, three voltage sensors measure line voltages , ,

and across the STATCOM side of the step-down transformer, two current
sensors (I3 and I4) measure line currents and flowing through the
STATCOM side of the step-down transformer, and a fourth voltage sensor (E1)
measures voltage across the dc side of the STATCOM. Signals representing
these voltages and currents are sent to the STATCOM controller (which is set for
automatic voltage control).
The STATCOM controller compares the measured line voltages to the ac bus
line voltage command , and determines the error in the measured line
voltages across the STATCOM side of the step-down transformer. The
STATCOM controller also compares the measured dc voltage to the dc bus
voltage command , and determines the error in the measured voltage
across the dc side of the STATCOM. Using these calculated error values and the
measured voltage and current values, the STATCOM controller determines the
switching signals to be applied to the three-phase bridge so that:
1) the amount of reactive power the STATCOM exchanges with the ac power
system to which it is connected ensures that the line voltages measured
across the STATCOM side of the step-down transformer are equal to the
ac bus line voltage command; and
2) the amount of active power flowing through the STATCOM makes the
voltage measured across the dc side of the STATCOM equal to the dc bus
voltage command. Note that the signal representing line voltage is also
used to provide the phase angle () information required to perform
mathematical calculations in the controller. The operation of a
STATCOM controller designed for automatic voltage control is covered in
further detail in Appendix D.
Figure 20. The voltage across a STATCOM designed for automatic voltage compensation is
controlled using a voltage control loop. This ensures that the voltage across the STATCOM is
maintained virtually constant ( Copyright 2012 Guc Kalitesi).

Exercise 1 Voltage Compensation of AC Transmission Lines Using a STATCOM Procedure Outline
PROCEDURE OUTLINE The Procedure is divided into the following sections:
Set up and connections

Voltage compensation at the receiver end of an ac transmission line
using a STATCOM
PROCEDURE
High voltages are present in this laboratory exercise. Do not make or modify any
banana jack connections with the power on unless otherwise specified.
Set up and connections
In this section, you will set up a circuit consisting of an ac transmission line

supplying power to a resistive load, with a STATCOM at the receiver end of the
line for voltage compensation. You will then set up the measuring equipment
required to study the operation of the STATCOM when it is used for voltage
compensation.
1. Refer to the Equipment Utilization Chart in Appendix A to obtain the list of

equipment required to perform this exercise.
Install the required equipment in the Workstation.
2. Make sure the ac and dc power switches on the Power Supply are set to
the O (off) position, then connect the Power Supply to a three-phase
ac power outlet.
3. Connect the Power Input of a Data Acquisition and Control Interface to

the 24 V ac power supply.
Connect the Power Inputs of both Data Acquisition and Control Interfaces
together.
Connect the Low Power Input of the IGBT Chopper/Inverter to the Power
Input of any of the Data Acquisition and Control Interface modules.
Turn the 24 V ac power supply on.
4. Connect the USB port of each Data Acquisition and Control Interface to a
USB port of the host computer.

Exercise 1 Voltage Compensation of AC Transmission Lines Using a STATCOM Procedure
5. Turn the host computer on, then start the LVDAC-EMS software.
In the LVDAC-EMS Start-Up window, make sure that both Data Acquisition
and Control Interface modules are detected. Make sure that the STATCOM
Control and Computer-Based Instrumentation functions are available for
either or both Data Acquisition and Control Interface modules. Select the
network voltage and frequency that correspond to the voltage and frequency
of your local ac power network, then click the OK button to close the
LVDAC-EMS Start-Up window.
6. Before you begin connecting the equipment, record in the space below the
serial number of the Data Acquisition and Control Interface (DACI) you will
use to control the STATCOM, and the serial number of the DACI you will use
for data acquisition.
Serial number of the DACI controlling the STATCOM:
Serial number of the DACI used for data acquisition:
7. Connect the equipment as shown in Figure 21 and Figure 22. Use the Power
Supply to implement the three-phase ac power source. Note that points A1,
A2, A3, and A4 in Figure 21 are to be connected to the corresponding points
in Figure 22.
a In Figure 21 and Figure 22, voltage and current inputs shown in blue
represent inputs of the Data Acquisition and Control Interface used to control
the STATCOM, while voltage and current inputs shown in red represent inputs
of the Data Acquisition and Control Interface used for data acquisition. Note
that the inputs used for STATCOM control purposes cannot be used for data
acquisition, and vice versa.
This circuit represents an ac transmission line that is voltage compensated at

the receiver end of the line, using a STATCOM. The resistive load in the
circuit represents the electrical power demand. By changing the resistance of
the load, it is thus possible to vary the electrical power demand.

AC power network, transmission line, and load
Three-Phase Transmission
Line module Load

L1

L2

L3
A1 A2 A3 A4
To STATCOM
Resistance value of loads , ,

Local ac power network Line inductive ()
reactance
Voltage Frequency ()
1st 2nd 3rd 4th 5th 6th
(V) (Hz)
120 60 120 600 400 300 240 200 171
220 50 400 2200 1467 1100 880 733 629
240 50 400 2400 1600 1200 960 800 686
220 60 400 2200 1467 1100 880 733 629
Figure 21. Circuit for studying the operation of a STATCOM used for voltage compensation of
an ac transmission line supplying power to a resistive load.

Static synchronous compensator (STATCOM)
Three-Phase Transformer module
A1
1 2
7
To receiver end of the transmission line
12
8
A2
3 4
9
11
10
A3
5 6
A4
Line Inductors
module Three-Phase Filter IGBT Chopper/Inverter module

Switching control signals

from the control DACI
Figure 22. Circuit for studying the operation of a STATCOM used for voltage compensation of
an ac transmission line supplying power to a resistive load.

8. In the circuit of Figure 21, it is assumed that the ac transmission line is also
voltage compensated using fixed shunt inductors present along this line.
Such an ac transmission line can be represented by a single inductor (one
per phase) because the shunt inductors are sized so as to neutralize the
capacitors in the equivalent circuit of the line. This is illustrated in Figure 23.
Figure 23. One phase of an ac transmission line compensated with shunt inductors.
9. On the Data Acquisition and Control Interface used for controlling the
STATCOM, connect the Digital Output to the Switching Control Inputs of the
IGBT Chopper/Inverter using a DB9 connector cable.
On the IGBT Chopper/Inverter, make sure the Dumping switch is set to

the I position. This allows power to be dissipated in a dump resistor inside
the IGBT Chopper/Inverter in the event of an overvoltage across the
IGBT Chopper/Inverter. This additional protection has no effect on the
STATCOM operation.
10. On the Three-Phase Transmission Line, make sure the I/O toggle switch is
set to the I position, then set the inductive reactance selector to the value
indicated in the table of Figure 21 for your local ac power network voltage
and frequency.
On the Resistive Load, make the necessary switch settings to obtain

the 1st resistance value indicated in the table of Figure 21 for your local
ac power network voltage and frequency.
a Appendix C lists the switch settings required on the Resistive Load, the
Inductive Load, and the Capacitive Load in order to obtain various
resistance (or reactance) values.
11. In LVDAC-EMS, open the STATCOM Control window. A dialog box appears.
Select the serial number of the Data Acquisition and Control Interface used
to control the STATCOM (recorded in step 6), then click the OK button to
close the dialog box and open the STATCOM Control window.

In the STATCOM Control window, make the following settings:
Make sure that the Control Mode parameter to Automatic Voltage

Control. This control mode allows the voltage of the ac power system to
which the STATCOM is connected to be automatically compensated and
maintained at a specified value (e.g., at the voltage of your local
ac power network).
a In order to implement this control mode, the Data Acquisition and Control
Interface used for controlling the STATCOM requires that voltage
inputs E1, E2, E3, and E4, as well as current inputs I3 and I4, be connected as
shown in the circuit of Figure 21 and Figure 22.
Make sure that the DC Bus Voltage Command parameter is set

to 200.0 V. This dc voltage value is high enough to allow the STATCOM
to exchange reactive power with the ac power system to which it is
connected (i.e., it is high enough to allow the STATCOM to produce
ac voltage at the required value).
Make sure the AC Bus Line Voltage Command parameter is set
to 83.0 V. With this line voltage command value, the
STATCOM controller automatically adjusts the amount of reactive power
supplied or absorbed by the STATCOM so that the line voltage across
the STATCOM side of the three-phase transformer is maintained at 83 V.
Due to the transformer voltage ratio and configuration (Y-), the
measured line voltage across the ac power system connected to
the STATCOM should be close to your local ac power network line
voltage.
Make sure that the Active Current Controller Prop. Gain (Kp1) is set
to 5.00.
Make sure that the Active Current Controller Int. Gain (Ki1) is set
to 20.00.
Make sure that the Reactive Current Controller Prop. Gain (Kp2) is set
to 10.00.
Make sure that the Reactive Current Controller Int. Gain (Ki2) is set
to 20.00
Make sure that the DC Bus Voltage Controller Prop. Gain (Kp3) is set
to 5.00.
Make sure that the DC Bus Voltage Controller Int. Gain (Ki3) is set
to 5.00.
Make sure that the AC Bus Line Voltage Controller Prop. Gain (Kp4) is
set to 2.50.
Make sure that the AC Bus Line Voltage Controller Int. Gain (Ki4) is set
to 10.00.
Make sure that the Status parameter is set to Stopped. This ensures that
the Static Synchronous Compensator function is stopped.

12. In LVDAC-EMS, open the Metering window. A dialog box appears. Select the
serial number of the Data Acquisition and Control Interface used for data
acquisition (recorded in step 6), then click the OK button to close the dialog
box and open the Metering window.
In the Option menu of the Metering window, select Acquisition Settings to

open the corresponding dialog box. Set the Sampling Window to 8 cycles,
then click OK to close the dialog box. This provides better accuracy when
measuring parameters (e. g., reactive power) of the STATCOM.
Make the required settings in order to measure the rms values (ac) of the line
voltage (input E1) at the sender end of the ac transmission line, and the
line voltage (input E2) at the receiver end of the ac transmission line.
Also, set set a meter to measure the three-phase reactive power that
the STATCOM exchanges with the ac power system to which it is connected
[metering function PQS2 (E2, I2) 3~].
Voltage compensation at the receiver end of an ac transmission line using a

STATCOM
In this section, you will vary the resistance of the load and, for each resistance
value, you will record the three-phase PWM rectifier/inverter active current and
reactive current, the reactive power exchanged by the STATCOM, the sender
voltage, and the receiver voltage. You will analyze the results and determine how
accurately the STATCOM achieves voltage compensation when load variations
occur. You will then use the Oscilloscope to record the transient in the receiver
voltage and current when the resistive load decreases suddenly, and when it
increases suddenly. Using the signals recorded on the Oscilloscope, you will
determine how fast the STATCOM achieves voltage compensation when load
variations occur.
Accuracy of the voltage compensation achieved by a STATCOM when load variations

occur
13. On the Power Supply, turn the three-phase ac power source on.
14. In the STATCOM Control window, start the static synchronous compensator
by clicking the Start/Stop button or by setting the Status parameter to
Started.
15. In the STATCOM Control window, adjust the AC Bus Line Voltage Command
parameter so that the receiver voltage indicated in the Metering window is
as close as possible to the nominal value of your local ac power network
voltage.

16. Fill in Table 2 as indicated below:
On the Resistive Load, successively set the resistance of loads ,

, and to each of the values indicated in the table of Table 2 for
your local ac power network voltage and frequency.
For each load resistance value, record in the corresponding row of

Table 2 the three-phase PWM rectifier/inverter active
current and reactive current (indicated in the
STATCOM Control window), as well as the reactive power
exchanged by the STATCOM, the sender voltage , and the
receiver voltage (indicated in the Metering window).
Table 2. Three-phase PWM rectifier/inverter active current and reactive current , reactive power
exchanged by the STATCOM, sender voltage , and receiver voltage for different resistive load values when the
STATCOM compensates the voltage at the receiver end of an ac transmission line.
Resistance Active current Reactive Reactive Sender Receiver

value of loads current power voltage voltage
, , (A) (var) (V) (V)
() (A)
1st
2nd
3rd
4th
5th
6th
The results are presented in the following table.
Three-phase PWM rectifier/inverter active current and reactive current , reactive power exchanged by
the STATCOM, sender voltage , and receiver voltage for different resistive load values when the STATCOM compensates
the voltage at the receiver end of an ac transmission line.
Resistance Active current Reactive Reactive Sender Receiver

value of loads current power voltage voltage
, , (A) (var) (V) (V)
() (A)
1st 600 -0.02 -0.2 -9.55 209 209
2nd 400 -0.04 -0.3 -23.3 209 209
3rd 300 -0.04 -0.43 -42.9 209 209
4th 240 -0.09 -0.59 -69.8 209 209
5th 200 -0.11 -0.86 -103 209 209
6th 171 -0.15 -1.18 -158 209 209

17. In the STATCOM Control window, stop the static synchronous compensator
Stopped.
On the Power Supply, turn the three-phase ac power source off.
18. From the results recorded in Table 2, does the STATCOM accurately
compensate the voltage across the ac power system to which it is
connected (i.e., the receiver voltage )? Explain briefly.
Yes, since the results in the table indicate that the STATCOM maintains the
voltage across the ac power system to which it is connected (i.e., the
receiver voltage ) virtually equal to the ac power network voltage (i.e., the
sender voltage ) no matter the power demand of the consumers (i.e., no
matter the resistive load value). This shows that a STATCOM accurately (i.e.,
almost perfectly) compensates variations of the voltage across the ac power
system to which it is connected.
Compare the accuracy of the voltage compensation achieved using

a STATCOM to that which can be achieved using a bank of switched
shunt-capacitors. What can you conclude? Explain briefly.
As the results in the table indicate, a STATCOM accurately (i.e., almost

perfecty) compensates the voltage across the ac power system to which it is
connected. On the other hand, a bank of switched shunt inductors can rarely
achieve perfect voltage compensation of the ac power system to which it is
connected. This is because the selection of shunt inductors available for
voltage compensation is limited. Therefore, a STATCOM generally achieves
a much more accurate voltage compensation of an ac power system than a
bank of switched shunt inductors.
19. From the results recorded in Table 2, explain how the STATCOM
compensates the voltage across the ac power system to which it is
connected (i.e., the receiver voltage ).
The STATCOM compensates the voltage of the ac power system to which it

is connected (i.e., the receiver voltage ) by adjusting the magnitude and
polarity of the reactive component of the current flowing through its
ac side (i.e., the reactive current component of the three-phase
PWM rectifier/inverter), in order to exchange just the right amount of reactive
power (in the present case, the STATCOM supplies reactive power) to meet
the reactive power requirement of the system. This ensures that the voltage
across the ac power system connected to the STATCOM is maintained
virtually equal to the ac power network voltage, no matter the reactive power
requirement of the system.

Speed of the voltage compensation achieved by a STATCOM during load variations
20. On the Resistive Load, set the resistance of loads , , and to the
1st value indicated in Table 3 for your local ac power network voltage and
frequency.
Table 3. Resistance values of loads , , and to be used for observing the speed of the
voltage compensation achieved by the STATCOM when a load variations occurs.
Local ac power Resistive loads , ,

network ()
Voltage Frequency
1st 2nd
(V) (Hz)
120 60 200 600
220 50 733 2200
240 50 800 2400
220 60 733 2200
21. On the Power Supply, turn the three-phase ac power source on.
22. In the STATCOM Control window, start the static synchronous compensator
Started.
23. In LVDAC-EMS, open the Oscilloscope. Make the appropriate settings in

order to observe the waveform of the voltage (input E2) and
current (input I2) at the receiver end of the ac transmission line.
Set the Oscilloscope as indicated below in order to be able to perform the

next manipulation:
a The settings below ensure that the Oscilloscope will start recording data at the
instant when the peak value of voltage becomes higher than its nominal
peak value, i.e., when the load resistance at the receiver end of the line
increases suddenly.
Set the sensitivity of the channel used to observe the receiver

voltage to 200 V/div.
Set the sensitivity of the channel used to observe the receiver

current to 1 A/div.
Set the time base to 0.1 s/div.
Set the trigger type to Hardware. Set the trigger source to the
channel used to observe the receiver voltage , and the trigger level
to about 10 V higher than the peak value of the receiver voltage.

Adjust the horizontal position of the trigger point to about 4 divisions

from the left-hand side of the oscilloscope screen.
On the Oscilloscope, click the Single Refresh button.
24. Create a sudden increase in load resistance at the receiver end of the line to
simulate a sudden decrease in the power demand of the consumers. To do
so, set the resistance of loads , , and on the Resistive Load to the
2nd value indicated in Table 3 for your local ac power network and voltage.
a For optimal results, modify the switch settings simultaneously on the three legs
of the Resistive Load in order to avoid operation with an unbalanced load as
much as possible.
If no signal appear on the Oscilloscope (i.e., if the Oscilloscope does not trig)
at the instant the sudden increase in load resistance occurs, set the load
resistance of loads , , and back to the 1st value indicated in Table 3,
then repeat the above manipulation until voltage and current waveforms
appear on the Oscilloscope.
On the Oscilloscope, save the currently-displayed voltage and current

waveforms to the first memory. These waveforms will be used later in the
exercise.
The resulting waveforms are shown below.
Oscilloscope Settings
Channel-1 Input .............................. E2 Receiver voltage
Channel-1 Scale ................... 200 V/div
Channel-1 Coupling ........................ DC
Channel-2 Input ................................ I2
Channel-2 Scale ....................... 1 A/div
Show Cursors ......................Horizontal
Time Base .............................. 0.1 s/div
Trigger Type ........................ Hardware
Trigger Source .............................. Ch1
Trigger Level .............................. 310 V
Trigger Slope ............................. Rising
Receiver current
Receiver voltage and receiver current when the STATCOM compensates the voltage
after a sudden increase in load resistance at the receiver end of an ac transmission line.

25. On the Oscilloscope, make the following settings:
a The settings below ensure that the Oscilloscope will start recording data when
the peak value of the receiver current becomes higher than its nominal peak
value, i.e., when the load resistance at the receiver end of the line decreases
suddenly.
Leave the trigger type set to Hardware. Set the trigger source to the
channel used to observe the receiver current , and the trigger level
to about 0.1 A higher than the peak value of the receiver current.
Click the Single Refresh button.
26. Create a sudden decrease in load resistance at the receiver end of the line to
simulate a sudden increase in the power demand of the consumers. To do
so, set the resistance of loads , , and on the Resistive Load to the
1st value indicated in Table 3 for your local ac power network and voltage.
a For optimal results, modify the switch settings simultaneously on the three legs
of the Resistive Load in order to avoid operation with an unbalanced load as
much as possible.
On the Oscilloscope, save the currently-displayed voltage and current

waveforms to the second memory.
The resulting waveforms are shown below.
Oscilloscope Settings
Channel-1 Input .............................. E2 Receiver voltage
Channel-1 Scale ................... 200 V/div
Channel-2 Input ................................ I2
Channel-2 Scale ....................... 1 A/div
Show Cursors ......................Horizontal
Time Base .............................. 0.1 s/div
Trigger Type ........................ Hardware
Trigger Source .............................. Ch2
Trigger Level ............................... 0.4 A
Trigger Slope ............................. Rising
Receiver current
Receiver voltage and receiver current when the STATCOM compensates the voltage
after a sudden decrease in load resistance at the receiver end of an ac transmission line.

Exercise 1 Voltage Compensation of AC Transmission Lines Using a STATCOM Conclusion
27. Observe the voltage and current waveforms saved to the memories of the
Oscilloscope. From your observations, does the STATCOM compensate
almost instantly for the voltage fluctuations across the ac power system to
which it is connected (i.e., the receiver voltage ) due to sudden variations
of the load? Explain briefly.
Yes. The voltage and current waveforms saved to the memories of the
Oscilloscope show that the STATCOM compensates almost instantly (i.e.,
within 5 cycles or less of the receiver voltage ) for the voltage fluctuations
at the receiver end of the ac transmission line caused by sudden variations of
the load.
28. In the STATCOM Control window, stop the static synchronous compensator
Stopped.
29. On the Power Supply, turn the three-phase ac power source off.
30. Close LVDAC-EMS, then turn off all the equipment. Disconnect all leads and
return them to their storage location.
CONCLUSION In this exercise, you familiarized yourself with the operating principles of
STATCOMs when they are used for voltage compensation of ac transmission
lines. You learned how a STATCOM controller designed for automatic voltage
control compensates the voltage across the ac power system to which the
STATCOM is connected.
REVIEW QUESTIONS 1. What are the two main advantages of STATCOMs over switched shunt
inductors when they are used for voltage compensation of ac transmission
lines?
When used for voltage compensation of ac transmission lines, the two main
advantages of STATCOMs over switched shunt inductors substations are:
Tighter control of the voltage compensation across the ac transmission

line.
Increased line stability during transients (i.e., during sudden changes in

the load at the receiver end of the ac transmission line), due to the
quickness of their STATCOM response.

Exercise 1 Voltage Compensation of AC Transmission Lines Using a STATCOM Review Questions
2. Which component acts as the dc power source in a STATCOM? How is the

voltage across that component maintained at a specific value? Explain
briefly.
A large capacitor acts as the dc power source in a STATCOM. The voltage

across this capacitor is maintained at a specific value by continually adjusting
the magnitude and polarity of the active component of the current at the
ac side of the STATCOM. When the voltage across the capacitor needs to be
increased, the STATCOM adjusts the magnitude and polarity of the active
component of the current flowing through its ac side so that active power is
drawn from the ac power system and converted to dc power in order to
charge the capacitor. Conversely, when the voltage across the capacitor
needs to be decreased, the STATCOM adjusts the magnitude and polarity of
the active component of the current flowing through its ac side so that active
power is returned to the ac power system, thereby discharging the capacitor.
3. What are the primary advantages of STATCOMs over SVCs?
The primary advantages of STATCOMs over SVCs are summarized below:
STATCOMs are not affected significantly when operating in undervoltage

conditions while SVCs are.
STATCOMs have a slightly faster response time than SVCs.
STATCOM installations are much smaller in size than SVC installations

of comparable ratings.
4. Describe how banks of switched shunt inductors and a STATCOM are

distributed along an ac transmission line covering a long distance. Explain
briefly.
In an ac transmission line covering a long distance, the voltage along the line
is compensated using banks of switched shunt inductors along the line,
which provide cost-effective voltage compensation. At the receiver end of the
ac transmission line, however, the voltage is generally compensated using a
bank of switched shunt inductors and a STATCOM. This ensures tighter
control of the voltage at the end of the line, as well as greater line stability
during transients. This is especially important at the end of the
ac transmission line, where the voltage must be carefully compensated
before the electrical power is distributed to consumers.

Exercise 1 Voltage Compensation of AC Transmission Lines Using a STATCOM Review Questions
5. Is it usual to replace all switched shunt inductors along an ac transmission

line covering a long distance with STATCOMs? Explain briefly.
No, it is not usual to replace all switched shunt inductors along an

ac transmission line covering a long distance with STATCOMs. This is due to
the fact that, even though STATCOMs are more efficient in every aspect than
switched shunt inductors, they are much more costly. Since the use of
switched shunt inductors to compensate voltage along ac transmission lines
already yields acceptable results, replacing all switched shunt inductors with
STATCOMs is usually not cost effective.

Bibliography
Acha, Enrique, Vassilios Agelidis, Olimpo Anaya-Lara, and T. J. E. Miller, Power
Electronic Control in Electrical Systems, 1st ed., Oxford: Newnes, 2002,
ISBN 978-0750651264.
Akagi, Hirofumi, Edson H. Watanabe, and Mauricio Aredes, Instantaneous Power

Theory and Applications to Power Conditioning, 1st ed., Piscataway: IEEE Press,
2007, ISBN 978-0470107614.
Glover, J. Duncan, Mulukutla S. Sarma, and Thomas J. Overbye, Power

Systems Analysis and Design, 5th ed., Stamford: Cengage Learning, 2012,
ISBN 978-1-111-42577-7.
Hingorani, Narain G. and Laszlo Gyugyi, Understanding FACTS, 1st ed.,

Piscataway: IEEE Press, 1999, ISBN 978-0780334558.
Padiyar, K. R., FACTS Controllers in Power Transmission and Distribution,

1st ed., New Delhi: New Age International ltd., 2009, ISBN 978-1848290105.
Sood, Vijay K., HVDC and FACTS Controllers, 1st ed., Boston: Kluwer Academic
Publishers, 2004, ISBN 978-1402078903.
Wildi, Theodore, Electrical Machines, Drives, and Power Systems, 6th ed., Upper
Saddle River: Prentice Hall, 2005, ISBN 978-0131776913.

Static Compensator Statcom PDF

Uploaded by

Copyright:

Available Formats

Static Compensator Statcom PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Static Compensator Statcom PDF

Uploaded by

Copyright:

Available Formats

Electricity and New Energy

Static Synchronous Compensator

By the staff of Festo Didactic

Festo Didactic Lte/Ltd, Quebec, Canada 2012

DANGER indicates a hazard with a high level of risk which, if not

WARNING indicates a hazard with a medium level of risk which,

CAUTION indicates a hazard with a low level of risk which, if not

CAUTION used without the Caution, risk of danger sign ,

Caution, risk of electric shock

Caution, hot surface

Caution, risk of danger

Caution, lifting hazard

Caution, hand entanglement hazard

Notice, non-ionizing radiation

Both direct and alternating current

Three-phase alternating current

Earth (ground) terminal

Festo Didactic 86371-10 III

Protective conductor terminal

Frame or chassis terminal

Equipment protected throughout by double insulation or

In position of a bi-stable push control

Out position of a bi-stable push control

IV Festo Didactic 86371-10

Introduction Static Synchronous Compensator (STATCOM) ........................ 1

Exercise 1 Voltage Compensation of AC Transmission Lines Using

Exercise 2 Dynamic Power Factor Correction Using a STATCOM .......... 35

Appendix A Equipment Utilization Chart ...................................................... 59

Appendix B Glossary of New Terms ............................................................. 61

Appendix C Impedance Table for the Load Modules .................................. 63

Festo Didactic 86371-10 V

Appendix D STATCOM Controller Operation ............................................... 65

Index of New Terms ............................................................................................. 73

VI Festo Didactic 86371-10

The Electric Power Technology Training Program.

Festo Didactic 86371-10 VII

We invite readers of this manual to send us their tips, feedback, and

Please send these to did@de.festo.com.

VIII Festo Didactic 86371-10

STATCOMs can be used for voltage compensation at the receiver end of

This course, Static Synchronous Compensators (STATCOMs), teaches the basic

Festo Didactic 86371-10 IX

X Festo Didactic 86371-10

Festo Didactic 86371-10 XI

Festo Didactic 86371-10 XIII

Voltage Compensation of AC Transmission Lines Using a

Voltage compensation of ac transmission lines using a STATCOM

DISCUSSION Voltage compensation of ac transmission lines using a STATCOM

One way to achieve coarse compensation of voltage variations across an ac

Figure 17 shows a typical ac transmission line used to transfer large amounts of

Festo Didactic 86371-10 15

Segment Segment Segment

Receier end (to distribution network)

As Figure 17 shows, the ac transmission line is divided into three segments of

16 Festo Didactic 86371-10

Instead of using a STATCOM, several inductors with different values of

It is possible to replace all switched shunt inductors in the substations of the

Festo Didactic 86371-10 17

Automatic voltage compensation

Make sure that the Control Mode parameter to Automatic Voltage

Make sure that the DC Bus Voltage Command parameter is set

On the Resistive Load, successively set the resistance of loads ,

For each load resistance value, record in the corresponding row of

Set the sensitivity of the channel used to observe the receiver