HP 1 Heat Pipe

TECHNICAL DATA SHEET
HP-1 Heat Pipe
Heat In
In
Heat Out
Sintered Powder Wick
Liquid Turning to Vapor
 HIGH POWER DENSITIES SINTERED COPPER POWDER WICK
 OPERATION IN ANY ORIENTATION The HP-1 is a high performance heat

pipe designed to handle demanding
Sintered Powder Wick
 WITHSTANDS -65°C ENVIRONMENTS applications. With a power density

capacity of 250 W/cm2 and the ability
to operate against gravity, the HP-1
The HP-1’s high performance sintered wick structure permits the will provide effective cooling for
effective operation of the heat pipe in any orientation. See Figures 1 electronic components. The Sintered
for thermal performance. This wick structure assures the HP-1 will Copper Wick structure shown in the
tolerate continual freeze/thaw cycling found in many commercial image to the right.
and military applications.
The HP-1 Heat Pipe is available in diameters of .250" (6.35mm),

.375" (9.52), .500" (12.7) and .625" (15.88). It is available in lengths
from 3" (76) through 18" (457). The HP-1 heat pipe is manufactured
with a copper envelope, copper sintered wick structure and water
as the working fluid. The HP-1’s nominal operating temperature is
10°C to 180°C. Operation above 180°C is possible with special
provisions.
Figure 1. HP-1 Thermal Performance

Figure 2. HP-1 Thermal Performance
Aavid Thermacore, Inc. Page 1 of 2
780 Eden Road
Lancaster, PA 17601-4794 USA
Phone: 717-569-6551 © Aavid Thermacore 2017. All rights reserved.
Info.thermacore@aavid.com Subject to change without notice—April 2017
www.thermacore.com and www.aavid.com
TECHNICAL DATA SHEET
OPERATION also manufactures Cabinet Coolers and Liquid to Air Heat

Exchangers.
Maximum power density in the evaporator is 250 W/cm2. The
HP-1 will withstand the effects of freeze/thaw cycles and can
tolerate storage temperature of -55° to 180° C.
The HP-1 Heat Pipe is intended to be clamped, epoxied or
soldered to both the heat source and heat sink. When soldering,
avoid heating above 180° C. The HP-1’s design is proven and
has a substantial safety margin to accommodate variation in both
manufacture and use. It is manufactured under uncompromising
quality control with each production run subjected to complete
testing. The world’s largest life testing program on heat pipes is
conducted under the supervision of Aavid Thermacore’s
Engineering Department. This assures the guaranteed life of the
HP-1 Heat Pipe.
SAFETY
The end seal of the HP-1 is designed to open in the temperature
range of 180°C, which provides a safe release for internal
pressure. It is the responsibility of the user to make provisions to
assure the HP-1 will not be operated above its stated maximum
HEAT PIPE APPLICATION
operating temperature. After the high internal pressure is
The evaporator of the HP-1 is shown soldered to a copper plate released, the heat pipe is inoperable.
that is a mounting plate for high power electronic components.
The HP-1 is made from annealed copper and is easily bent. Care
The heat pipe’s condenser is then attached to a liquid cooled
must be taken to make sure the heat pipe is not damaged by
heat sink. This application is in an electronic tester that is subject
rough handling or dropping.
to operation in any orientation.
LIMITED WARRANTY
ORDERING INFORMATION
Aavid Thermacore warrants the HP-1 Heat Pipe to perform in
The standard HP-1 Heat Pipe is available in four diameters:
accordance with the information on this sheet for one year from
.250" (6.35), .375" (9.521), .500" (12.7) and .625" (15.88) and in
date of purchase. There are no warranties which extend
lengths from 3" (76) to 18" (457). Order the diameter and length
beyond the description stated herein. Aavid Thermacore will,
that is required for your application. When ordering, make
at its option, repair or replace any HP-1 Heat Pipe determined by
allowances for the fill tube (inoperative length). The length
Aavid Thermacore to be defective, provided the HP-1 is returned
tolerance of the HP-1 is ±0.125" (3.17). Besides the standard
to Aavid Thermacore's factory transportation charges prepaid.
sizes of HP-1, Heat Pipes can be ordered from Aavid
Aavid Thermacore shall not be obligated to repair or replace any
Thermacore in a variety of sizes, shapes and performance
HP-1 Heat Pipe that has been abused, altered, operated outside
ratings. Other Aavid Thermacore products include customized
of its published rating or otherwise misused or damaged in any
Heat Pipe Assemblies, Isothermal Rollers as well as products for
way.
Military and Commercial electronics cooling. Aavid Thermacore
Aavid Thermacore, Inc. Page 2 of 2

780 Eden Road
Lancaster, PA 17601-4794 USA
Phone: 717-569-6551 © Aavid Thermacore 2017. All rights reserved.
Info.thermacore@aavid.com Subject to change without notice—April 2017
www.thermacore.com and www.aavid.com

HP 1 Heat Pipe

Uploaded by

Copyright:

Available Formats

HP 1 Heat Pipe

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HP 1 Heat Pipe

Uploaded by

Copyright:

Available Formats

TECHNICAL DATA SHEET

HP-1 Heat Pipe

Sintered Powder Wick

Liquid Turning to Vapor

 HIGH POWER DENSITIES SINTERED COPPER POWDER WICK

 OPERATION IN ANY ORIENTATION The HP-1 is a high performance heat

 WITHSTANDS -65°C ENVIRONMENTS applications. With a power density

The HP-1 Heat Pipe is available in diameters of .250" (6.35mm),

Figure 1. HP-1 Thermal Performance

OPERATION also manufactures Cabinet Coolers and Liquid to Air Heat

Aavid Thermacore, Inc. Page 2 of 2

You might also like