A4955

Full-Bridge PWM Gate Driver

FEATURES AND BENEFITS DESCRIPTION

• Standard IN1/IN2 control logic Designed for pulse-width-modulated (PWM) control of DC
• Overcurrent indication motors, the A4955 is capable of 50 V operation and provides
• Adjustable off-time and blank-time gate drive for an all N-channel external MOSFET bridge.
• Adjustable current limit
Input terminals are provided for use in controlling the speed and
• Adjustable gate drive
direction of a DC motor with externally applied PWM control
• Synchronous rectification
signals. Internal synchronous rectification control circuitry is
• Internal UVLO
provided to lower power dissipation during PWM operation.
• Crossover-current protection
• MOSFET VDS protection Internal circuit protection includes VDS protection, thermal
• Voltage output proportional to load current shutdown with hysteresis, undervoltage monitoring of VBB,
• A4955K is AEC-Q100 Grade 1 qualified and crossover-current protection.
• Commercial temperature grade (A4955G: –40°C to 105°C)
The A4955 is supplied in a low-profile 4 × 4 mm, 20-contact
• Automotive temperature grade (A4955K: –40°C to 125°C)
QFN package (suffix “ES”) and a 20-lead eTSSOP (suffix
“LP”), both with exposed thermal pad.
PACKAGES:
20-Pin QFN (suffix “ES”) 20-Pin eTSSOP (suffix “LP”)
with Exposed Thermal Pad with Exposed Thermal Pad

Not to scale

0.1 µF
CP1
CP2

TSD UVLO
VIN
CHARGE PUMP VCP
ISET 0.1 µF
VBB
VREG

RC VCP

STANDBY GHA GHA

SLEEPn GHB
SB
IN1 Control GATE
Logic DRIVE

IN2
SA SA

OCLn
OCL
GLA GLA
System Filter
GLB
Controller optional
AIOUT HOLD ×10
RSENSE
Inrush current limit =
+ SENSE
VREF/10 * RSENSE
–
VREF ÷10
GND

Functional Block Diagram

A4955-DS, Rev. 2 November 30, 2017

MCO-0000347
A4955 Full-Bridge PWM Gate Driver

SPECIFICATIONS

SELECTION GUIDE
Part Number Ambient Temperature Range Packing Notes
A4955GESTR-T –40°C to 105°C 1500 pieces per 7-inch reel
A4955GLPTR-T –40°C to 105°C 4000 pieces per 13-inch reel
A4955KLPTR-T –40°C to 125°C 4000 pieces per 13-inch reel AEC-Q100 Qualified

ABSOLUTE MAXIMUM RATINGS

Characteristic Symbol Notes Rating Unit
Load Supply Voltage VBB 50 V
Motor Outputs VSx VSx – VSENSE; VBB – VSx –2 to 52 V
–0.5 to 0.5 V
SENSE VSENSE
tW < 500 ns –4 to 4 V
OCLn VOCLn –0.3 to 5.5 V
VREF VREF –0.3 to 5.5 V
ISET VISET –0.3 to 5.5 V
AIOUT VAIOUT –0.3 to 5.5 V
Logic Input Voltage Range VIN SLEEPn, IN1, IN2 –0.3 to 5.5 V
Junction Temperature TJ 150 °C
Storage Temperature Range TS –55 to 150 °C
Range G –40 to 105 °C
Operating Temperature Range TA
Range K –40 to 125 °C

THERMAL CHARACTERISTICS (may require derating at maximum conditions; see application information)
Characteristic Symbol Test Conditions* Value Unit
ES Package 4-Layer PCB, 1 in.2 copper 37 °C/W
RθJA
LP Package 4-Layer PCB, 1 in.2 copper 28 °C/W

*Power dissipation and thermal limits must be observed.

Allegro MicroSystems, LLC 2

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
A4955 Full-Bridge PWM Gate Driver

VREF

OCLn
IN1

IN2
RC

GND 1 20 CP1
20

19

18

17

16
AIOUT 2 19 VBB

ISET 1 15 AIOUT OCLn 3 18 CP2

SLEEPn 2 14 GND VREF 4 17 VCP

SENSE 3 PAD 13 CP1 IN2 5 16 SA

PAD
GLB 4 12 VBB 6 15
IN1 GHA
GLA 5 11 CP2
RC 7 14 SB
10

8 13
6

9
7

ISET GHB
GHB

SB

GHA

SA

VCP

SLEEPn 9 12 GLA

SENSE 10 11 GLB

Package ES, 20-Pin QFN Pinouts Package LP, 20-Pin eTSSOP Pinouts

Terminal List Table

Number
Name Function
ES Package LP Package
ISET 1 8 Terminal to set gate drive current
SLEEPn 2 9 Sleep input, active low
SENSE 3 10 Sense resistor connection, low-side gate return
GLB 4 11 Gate driver
GLA 5 12 Gate driver
GHB 6 13 Gate driver
SB 7 14 High-side bridge reference
GHA 8 15 Gate driver
SA 9 16 High-side bridge reference
VCP 10 17 Charge pump reservoir cap connection
CP2 11 18 Charge pump terminal
VBB 12 19 Supply voltage
CP1 13 20 Charge pump terminal
GND 14 1 Ground
AIOUT 15 2 Analog output proportional to VSENSE
OCLn 16 3 OCP and OVP output flag, open drain
VREF 17 4 Analog OCP reference input
IN2 18 5 Digital IN2 input
IN1 19 6 Digital IN1 input
RC 20 7 Terminal to set blank- and off-time
PAD – –

Allegro MicroSystems, LLC 3

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
A4955 Full-Bridge PWM Gate Driver

ELECTRICAL CHARACTERISTICS: Valid for Temperature Range G version at TJ = 25°C and

for Temperature Range K version at TJ = –40°C to 150°C, VBB = 5.5 to 50 V, unless otherwise specified
Characteristics Symbol Test Conditions Min. Typ. Max. Unit
IBB – 6 10 mA
VBB Supply Current
IBB SLEEPn = low, Standby Mode – – 5 µA
GATE DRIVE
Relative to VBB, IGATE = 200 µA, VBB = 8 to 50 V 6.5 6.8 7.5 V
High-Side Gate Drive Output VGH
Relative to VBB, IGATE = 200 µA, VBB = 5.5 V – 5.2 – V
IGATE = 200 µA, VBB = 8 to 50 V 6.5 6.8 7.5 V
Low-Side Gate Drive Output VGL
IGATE = 200 µA, VBB = 5.5 V – 5.4 – V
Gate Drive Pull-Up Current IGPU RISET = 30 kΩ; VGH = VGL = 4 V 21 30 39 mA
Gate Drive Pull-Down Current IGPD RISET = 30 kΩ; VGH = VGL = 4 V 47 68 89 mA
Dead-Time tDT – 1000 – ns
Passive Pull-Down Resistance RGPD 30 50 70 kΩ
LOGIC INPUT AND OUTPUT
Logic Output Voltage VOCLn I = 2 mA, overcurrent detected – 0.2 0.3 V
Logic Output Leakage IOCLn V = 5 V, normal operation – – 5 µA
PWM Current Limit Flag Timer tOCLn 300 500 600 µs
VIH 2.0 – – V
Logic Input Voltage VIL – – 0.8 V
VIL(SLEEPn) SLEEPn input – – 0.4 V
Logic Input Hysteresis VHYS – 320 – mV
Logic Input Pull-Down Resistor RPD 30 50 70 kΩ
VREF Input Current IVREF VREF = 2.5 V –5 <1 5 µA
VREF Input Range VREF 0 – 2.5 V
Current Gain AV VREF / VSENSE, VREF = 2.5 V 9.5 – 10.5 V/V
Input Offset, SENSE VOSSENSE –10 – 10 mV
Fixed Off-Time tOFF RRC = 30 kΩ, CRC = 1 nF – 30 – µs
Percent Fast Decay PFD Internal PWM chop – 13 – %
Blank-Time tBLK RRC = 30 kΩ, CRC = 1 nF 2.1 3 3.9 µs
Power-Up Delay tpu Time until outputs are enabled – 50 300 µs
AIOUT Gain AIOUT AIOUT/VSENSE, VSENSE = 50 to 200 mV 9 10 11 V/V
Input Offset, AIOUT VOSAIOUT –15 – 15 mV
Sample-and-Hold Accuracy VSH(ACC) – 15 – mV
Sample-and-Hold Droop Rate VDROOP – – 1 mV/µs
AIOUT Output Impedance ROUT(AIOUT) 0.75 1.00 1.45 kΩ
PROTECTION CIRCUITS
UVLO Enable Threshold VBB(UVLO) VBB rising 5.10 5.25 5.40 V
UVLO Hysteresis VBB(UVLO,HYS) 200 300 350 mV
VDS Threshold VDSTH – 2 – V
Thermal Shutdown Temperature TJTSD Temperature increasing 150 165 185 °C
Thermal Shutdown Hysteresis ΔTJ Recovery = TJTSD – ΔTJ – 30 – °C

[1] Specified limits are tested at a single temperature and assured over operating temperature range by design and characterization.
[2] Target trip level = VDSTH = VDRAIN – VSx (High Side On) or VDSTH = VSx – VSENSE (Low Side On).

Allegro MicroSystems, LLC 4

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
A4955 Full-Bridge PWM Gate Driver

Control Logic
10 × VSENSE >
IN1 IN2 SLEEPn OUTA OUTB Function
VREF
x x 0 x Z Z Sleep (Standby) Mode
0 0 1 x Z Z Coast
0 1 1 false L H Reverse
1 0 1 false H L Forward
1 1 1 x L L Slow Decay SR (Brake)
0 1 1 true H/L L Internal Chop Reverse, Mixed Decay *
1 0 1 true L H/L Internal Chop Forward, Mixed Decay *
* In fast decay, outputs change to high-Z state when load current approaches zero, to prevent reversal of current.

IOCL = VREF / RSENSE / 10

I_OUT

tOCLn

OCLn

OCLn Output Flag

OCLn output function is described in the Functional Description section.

A A B B C
300 µs

AIOUT
0V

VSENSE = VREF /10

V SENSE
0V

IN 1
(IN2 = High)

AIOUT Output
A. Internal OCL chop. AIOUT holds while SENSE voltage varies during the mixed-decay off-time.
B. INx chop. AIOUT holds while SENSE voltage drops to 0 V during slow decay.
C. Slow-decay timeout. AIOUT is forced to 0 V 300 µs after ENABLE goes low.

Allegro MicroSystems, LLC 5

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
A4955 Full-Bridge PWM Gate Driver

FUNCTIONAL DESCRIPTION

Device Operation The formula for determining the gate drive is:

The A4955 is designed to operate DC motors. The output drivers 900

IGATE_HS (mA) = 1.9 +
are capable of 50 V with gate-driver capability for an all N-chan- RISET (kΩ)
nel external MOSFET H-bridge. Control logic includes syn-
1700
chronous rectification to reduce power dissipation. Current limit IGATE_LS (mA) = 3.5 +
is regulated by fixed off-time pulse-width-modulated (PWM) RISET (kΩ)
control circuitry. RC
Internal PWM Current Control The RC terminal is used to set both fixed off-time and blank-time
for the internal PWM current control. Refer to the following three
Peak current is regulated by monitoring the voltage on an exter- sections to select RC component values.
nal sense resistor.
IPEAK =
VREF Fixed Off-Time Setting
(10 × RSENSE) The internal PWM current-control circuitry uses a one-shot to
control the time the drivers remain off. The one-shot off-time
When the peak current is exceeded, the source driver turns off
(tOFF) is determined by the selection of an external resistor and
for a fixed period tOFF to chop the current. The outputs operate
capacitor connected from the RC timing terminal to ground. The
in mixed-decay mode during tOFF. Refer to the Fixed Off-Time
off-time, over a range of values of CRC = 470 to 1500 pF and
Setting section to set tOFF.
RRC = 12 to 100 kΩ, is approximated by:
The internal current-sense circuit is ignored for tBLANK after tOFF = RRC × CRC + dead time
PWM transitions. The comparator output is blanked to prevent
false overcurrent detection due to reverse recovery currents of the Blank-Time Setting
clamp diodes, or switching transients related to the capacitance of
the load, or both. Refer to the Blank-Time Setting section to set This circuit blanks the output of the current-sense comparator
tBLANK. when the outputs are switched by the internal current-control
circuitry or by an external PWM chop command. The comparator
Brake blanking time, tBLANK, is determined by the selection of an exter-
nal resistor and capacitor connected from the RC timing terminal
It is important to note that the internal PWM current-control to ground, and is approximated by:
circuit will not limit the current when braking, since the current (3.6/RRC (kΩ))
does not flow through the sense resistor. The maximum current tBLANK = 2.6 µs × CRC (nF) × e
can be approximated by VBEMF / RMOTOR. Care should be taken
to ensure that the maximum ratings of the external MOSFET are Slow Decay
not exceeded in worst-case braking situations of high speed and In slow-decay mode, the low-side switch stays on and the
high inertial loads. high-side switch turns off. Due to the synchronous rectification
feature, the complementary low-side switch turns on after a dead-
ISET time.
A resistor from ISET terminal to ground sets the magnitude of
the gate current. The sink and source current ratios are fixed at
Fast Decay SR
approximately 2-to-1 where the pull-down current is approxi- In fast-decay mode, the high-side and low-side switches turn off,
mately two times the pull-up current. RISET should be between and the complementary pair of switches is turned on, effectively
15 and 150 kΩ. reversing the voltage polarity across the motor winding.

Allegro MicroSystems, LLC 6

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
A4955 Full-Bridge PWM Gate Driver

Mixed Decay Charge Pump

When the peak current is reached, as set by the sense resistor and The charge pump is used to generate a supply above VBB to
voltage on VREF, the PWM current limiter initiates an off-time. drive the high-side MOSFETs. The VCP voltage is internally
The off-time is determined by the resistor and capacitor on the monitored and, in the case of a fault condition, the outputs of the
RC terminal. In mixed-decay mode, the driver will initiate a fast device are disabled.
decay, after a dead-time, for 13% of the programmed off-time.
After the fast-decay time expires, the bridge will switch to slow MOSFET VDS Protection
decay for the remaining off-time. When the bridge is operating The drain-to-source voltage is monitored across the MOSFET
in fast decay, it will internally prevent current reversal by putting any time the MOSFET is on. If the voltage across the MOSFET
the bridge in a high-Z state if the current through the sense resis- exceeds VDSTH, the bridge is disabled and latched off.
tor falls close to zero.
In order to prevent false VDS faults, the VDS monitor is blanked
OCLn Output immediately after any MOSFET is turned on. The VDS monitor
waits for a blank-time defined by the components on the RC ter-
An open-drain logic output will be driven low to indicate system
minal before monitoring the VDS level. During the off-time when
operation. The OCLn terminal is driven low under two condi-
SR is active, VDS blanking is fixed at 1 μs.
tions:
1. When the system is limiting current to value set by VREF and VDS Fault
RSENSE. Once overcurrent events are no longer detected, the When a VDS fault occurs, and the bridge is disabled, and the
A4955 will release the indication after a time tOCLn. fault is latched, the OCLn terminal is immediately driven low.
2. When a VDS fault is detected, the OCLn terminal is driven The latch can only be reset by going into standby or by dropping
low. It is released when the fault is reset. VBB below the UVLO threshold.
The OCLn terminal, in combination with the AIOUT terminal, Standby Mode
can provide valuable information about how the system is behav-
ing: Low power standby mode is activated when SLEEPn is brought
low. Standby mode disables most of the internal circuitry, includ-
• Overcurrent events can indicate a motor stall condition, in ing the charge pump and internal regulator. When coming out of
which case the system controller can respond to the fault standby mode, the A4955 requires up to 300 μs before the outputs
condition by reducing PWM duty. When OCLn is low and the can respond to input commands.
voltage on AIOUT is greater than 0 V, the controller is actively
limiting current with the internal, fixed off-time PWM current TSD
limiter.
If the die temperature increases to approximately TTSD, the full
• In the case of a VDS fault, the OCLn terminal is also driven bridge outputs will be disabled until the internal temperature falls
low, but the AIOUT voltage will be 0 V, because the bridge below TTSD minus a hysteresis level of THYS.
has been disabled. This notifies the user that a VDS fault has
occurred and the driver has been disabled. Fault Shutdown
AIOUT In the event of a fault due to excessive junction temperature,
or low voltage on VCP or VBB, the outputs of the device are
An analog output can be used to monitor current through the disabled until the fault condition is removed. At power-up, the
external sense resistor (if used). The SENSE voltage is gained by UVLO circuit disables the drivers until the UVLO thresholds are
a factor of 10 and fed to the AIOUT terminal. A sample-and-hold exceeded.
circuit is used to capture the voltage across the sense resistor and
holds it during periods when the voltage is not representative of
the current in the motor. The AIOUT Output diagram illustrates
when the voltage is held. The held voltage will droop at a rate
equal to VDROOP. In the case of a VDS fault on the bridge, the
AIOUT terminal will be discharged to zero volts.

Allegro MicroSystems, LLC 7

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
A4955 Full-Bridge PWM Gate Driver

TERMINAL CIRCUIT DIAGRAMS

IN1
SX VCP IN2
RISET
6.7 V AIOUT
VREF
SLEEPn
RC 10 V
OCLn
GND
GND

VCP
VBB GHX

8V 6.7 V
GLX SX
GND GND
SENSE

CP2
VCP CP1
8V

GND
VBB GND
GND

SENSE
VBB
56 V

GND 8V GND

GND

Allegro MicroSystems, LLC 8

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
A4955 Full-Bridge PWM Gate Driver

PACKAGE OUTLINE DRAWINGS

For Reference Only – Not for Tooling Use

(Reference JEDEC MO-220WGGD)
Dimensions in millimeters
NOT TO SCALE
Exact case and lead configuration at supplier discretion within limits shown

0.30
4.00 ±0.15 0.50
20
20
0.95
1
2 A 1
2
4.00 ±0.15 2.45 4.10

2.45
21X D C
4.10
0.08 C 0.75 ±0.05
SEATING
PLANE C PCB Layout Reference View
+0.05
0.25
–0.07
0.50 BSC
+0.15
0.40
–0.10

A Terminal #1 mark area

B B Exposed thermal pad (reference only, terminal #1 identifier appearance at supplier

2.45 discretion)
2 C Reference land pattern layout (reference IPC7351 QFN50P400X400X80-21BM);
1 all pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to
meet application process requirements and PCB layout tolerances; when mounting
on a multilayer PCB, thermal vias at the exposed thermal pad land can improve
20 thermal dissipation (reference EIA/JEDEC Standard JESD51-5)

2.45 D Coplanarity includes exposed thermal pad and terminals

ES Package, 20-Pin QFN with Exposed Thermal Pad

Allegro MicroSystems, LLC 9

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
A4955 Full-Bridge PWM Gate Driver

For Reference Only – Not for Tooling Use

(Reference MO-153 ACT)
NOT TO SCALE
Dimensions in millimeters
Exact case and lead configuration at supplier discretion within limits shown

6.50 ±0.10

4.20
8º
0º
20
0.20
0.09

C
3.00 4.40 ±0.10 6.40 ±0.20

1.00 REF
0.60 ±0.15
1 2

0.25 BSC
20X C
1.20 MAX SEATING PLANE
0.10 C SEATING
PLANE GAUGE PLANE

0.30
0.65 BSC 0.15
0.19
0.00
0.45 0.65

NNNNNNN
20 YYWW
LLLLLLL
1.70
1

D Standard Branding Reference View

N = Device part number
= Supplier emblem
Y = Last two digits of year of manufacture
W = Week of manufacture
3.00 6.10 L = Lot number

A Terminal #1 mark area

B Reference land pattern layout (reference IPC7351 SOP65P640X110-21M);

all pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary
to meet application process requirements and PCB layout tolerances; when
mounting on a multilayer PCB, thermal vias at the exposed thermal pad land
can improve thermal dissipation (reference EIA/JEDEC Standard JESD51-5)
1 2
C Exposed thermal pad (bottom surface)
4.20
D Branding scale and appearance at supplier discretion
B PCB Layout Reference View

LP Package, 20-Pin eTSSOP with Exposed Thermal Pad

Allegro MicroSystems, LLC 10
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
A4955 Full-Bridge PWM Gate Driver

Revision History
Revision Revision Date Description of Revision
– February 12, 2015 Initial Release
Updated functional block diagram (page 1); added packing information (page 2); changed
1 July 14, 2015
references to LSS to SENSE
2 November 30, 2017 Updated ISET section (page 6)

Copyright ©2017, Allegro MicroSystems, LLC

Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to
permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that
the information being relied upon is current.
Allegro’s products are not to be used in any devices or systems, including but not limited to life support devices or systems, in which a failure of
Allegro’s product can reasonably be expected to cause bodily harm.
The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its
use; nor for any infringement of patents or other rights of third parties which may result from its use.

For the latest version of this document, visit our website:

www.allegromicro.com

Allegro MicroSystems, LLC 11

115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com