Data Sheet DS/264GS/AS-EN Rev.

Model 264GS Gauge

ABB 2600T Series

Engineered solutions
for all applications

Base accuracy : ±0.075% Flexible configuration facilities

– provided locally via local keys combined with LCD
indicator or via hand held terminal or PC configuration
Span limits platform
– 0.2 to 60000kPa; 0.8inH2O to 8700psi
– 0.3 to 3000kPa abs; 2.25mmHg to 435psia

Multiple protocol availability

Reliable sensing system coupled with very latest – provides integration with HART®, PROFIBUS PA
digital technologies and FOUNDATION Fieldbus platforms offering
– provides large turn down ratio up to 100:1 interchangeability and transmitter upgrade capabilities

Comprehensive sensor choice Full compliance with PED Category III

– optimize in-use total performance and stability

5–year stability
2600T Pressure Transmitters
Model 264GS,

Functional Specifications Operative limits

Range and span limits Temperature limits °Χ (°F) :
Ambient (is the operating temperature)
Lower Range Minimum span
Sensor Upper Range Silicone oil filling: –40°C and +85°C (-40°F and +185°F)
Limit (LRL)
Code Limit (URL) for 264GS 264GS 264AS Inert filling and white oil: –20°C and +85°C (–4°F and +185°F)
gauge absolute
0.2kPa 0.3kPa Lower limit for LCD indicators and Viton gasket: –20°C (–4°F)
6kPa –6kPa 2mbar 3mbar
C 60mbar –60mbar 0.8inH2O 2.25mmHg Lower limit for perfluoroelastomer gasket: –15°C (+5°F)
24inH2O –24inH2O
Upper limit for LCD indicators: +70°C (+158°F)
40kPa –40kPa 0.4kPa 2kPa Note : For Hazardous Atmosphere applications see the temperature
F 400mbar –400mbar 4mbar 20mbar range specified on the certificate/approval relevant to the aimed
160inH2O –160inH2O 1.6inH2O 15mmHg type of protection
250kPa 2.5kPa 12.5kPa
2500mbar 25mbar 125mbar Process
L 1000inH2O
0 abs
10inH2O 93.8mmHg Lower limit

3000kPa 30kPa 150kPa – –50°C (–58°F); –20°C (–4°F) for Viton gasket.
U 30bar 0 abs 0.3bar 1.5bar
– –15°C (+5°F) for perfluoroelastomer gasket
435psi 4.35psi 21.7psi
10000kPa 100kPa Upper limit
100bar 1bar
R 1450psi 0 abs 14.5psi – Silicone oil, inert fluid and white oil: 121°C (250°F)
60000kPa 600kPa
600bar 6bar Storage
8700psi 87psi Lower limit: –50°C (–58°F); –40°C (–40°F) for LCD indicators
V 0 abs
Upper limit: +85°C (+185°F)

Note : Lower Range Limit (LRL) for 264AS is 0 abs for all ranges

Span limits
Maximum span = URL
IT IS RECOMMENDED TO SELECT THE TRANSMITTER SENSOR
CODE PROVIDING THE TURNDOWN VALUE AS LOWEST AS
POSSIBLE TO OPTIMIZE PERFORMANCE CHARACTERISTICS.

Zero suppression and elevation

Zero and span can be adjusted to any value within the range limits
detailed in the table as long as:

– calibrated span ε minimum span

Damping
Selectable time constant : 0, 0.25, 0.5, 1, 2, 4, 8 or 16s.
This is in addition to sensor response time

Turn on time
Operation within specification in less than 1s with minimum
damping.

Insulation resistance
> 100MΩ at 1000VDC (terminals to earth)

2
2600T Pressure Transmitters
Model 264GS,

Pressure limits Shock resistance

Acceleration: 50g
Overpressure limits (without damage to the transmitter)
0 absolute to Duration: 11ms

– 1MPa, 10bar, 145psi for sensor codes C, F (according to IEC 60068–2–27)

– 0.5MPa, 5bar, 72.5psi for sensor code L Wet and dust-laden atmospheres
– 6MPa, 60bar, 870psi for sensor code U The transmitter is dust and sand tight and protected against immersion
effects as defined by EN60529 (1989) to IP 67 (IP 68 on request) or by
– 20MPa, 200bar, 2900psi for sensor code R NEMA to 4X or by JIS to C0920. IP65 with Harting Han connector.
– 90MPa, 900bar, 13050psi for sensor code V
Hazardous atmospheres
– 0.6MPa, 6bar, 87psi for perfluoroelastomer gasket
With or without output meter/integral display
Proof pressure – COMBINED ATEX (Intrinsic safety and flameproof), FM and CSA
ZELM approval. See below detailed classifications.
The transmitter can be exposed without leaking to line pressure of up to – COMBINED INTRINSIC SAFETY and FLAMEPROOF/EUROPE:
– 1MPa, 10bar, 145psi for sensor codes C, F ATEX/ZELM approval
II 1 GD T50°C, EEx ia IIC T6 (–40°C δ Ta δ+40°Χ)
– 0.5MPa, 5bar, 72.5psi for sensor code L T95°C, EEx ia IIC T4 (–40°C δ Ta δ+85°Χ)
II 1/2 GD T85°C, EEx d IIC T6 (–40°C δ Ta δ +75°C)
– 6MPa, 60bar, 870psi for sensor code U
– INTRINSIC SAFETY/EUROPE:
– 20MPa, 200bar, 2900psi for sensor code R ATEX/ZELM approval
II 1 GD T50°C, EEx ia IIC T6 (–40°C δ Ta δ+40°Χ)
– 90MPa, 900bar, 13050psi for sensor code V T95°C, EEx ia IIC T4 (–40°C δ Ta δ+85°Χ)
– 0.6MPa, 6bar, 87psi for perfluoroelastomer gasket – TYPE "N"/EUROPE:
ATEX/ZELM type examination (for HART)
II 3 GD T50°C, EEx nL IIC T6 (–40°C δ Ta δ+40°Χ)
Environmental limits
T95°C, EEx nL IIC T4 (–40°C δ Ta δ+85°Χ)
Electromagnetic compatibility (EMC) – FLAMEPROOF/EUROPE:
ATEX/CESI approval
Comply with EN 61000–6–3 for emission and EN 61000–6–2 for II 1/2 GD T85°C, EEx d IIC T6 (–40°C δ Ta δ +75°C)
immunity requirements and test; – CANADIAN STANDARDS ASSOCIATION and FACTORY MUTUAL:
– Explosionproof: Class I, Div. 1, Groups A, B, C, D
Radiated electromagnetic immunity level: 30V/m – Dust ignitionproof : Class II, Div. 1, Groups E, F, G
(according to IEC 1000–4–3, EN61000–4–3) – Suitable for : Class II, Div. 2, Groups F, G; Class III, Div. 1, 2
Conducted electromagnetic immunity level : 30V – Nonincendive: Class I, Div. 2, Groups A, B, C, D
(according to IEC 1000–4-6, EN 61000–4–6) – Intrinsically safe: Class I, II, III, Div. 1, Groups A, B, C, D, E, F, G
AEx ia IIC T6/T4, Zone 0 (FM)
Surge immunity level (with surge protector): 4kV – STANDARDS AUSTRALIA (SAA): TS Approval
(according to IEC 1000-4–5 EN 61000–4–5) - Intrinsically safe Ex ia IIC T4/T5 (–20°C δ Ta δ+80°Χ) only HART
- No sparking Ex n IIC T4/T6 (–20°C δ Ta δ+80°Χ) only HART
Fast transient (Burst) immunity level: 4kV - Flameproof Ex d IIC T4/T6 (–20°C δ Ta δ+80°Χ)
(according to IEC 1000–4–4 EN 61000–4–4) - Dust ignitionproof DIP A21 Ta T6 (–20°C δ Ta δ+80°Χ)
– INTRINSIC SAFETY/CHINA
Pressure equipment directive (PED) NEPSI approvalEx ia IIC T4-T6
Comply with 97/23/EEC Category III Module H. – FLAMEPROOF/CHINA
NEPSI approvalEx d IIC T6
– GOST (Russia), GOST (Kazakhstan), Inmetro (Brazil)
Humidity
based on ATEX
Relative humidity: up to 100% annual average
Condensing, icing: admissible

Vibration resistance
Accelerations up to 2g at frequency up to 1000Hz
(according to IEC 60068–2–6)

3
2600T Pressure Transmitters
Model 264GS,

Electrical Characteristics and Options Optional surge protection

Up to 4kV
HART digital communication and 4 to 20mA output
– voltage 1.2 ∝σ rise time / 50 ∝σ delay time to half value
Power Supply
– current 8 ∝σ rise time / 20 ∝σ delay time to half value
The transmitter operates from 10.5 to 42VDC with no load and is
protected against reverse polarity connection (additional load allows
operations over 42VDC). Output signal

For EEx ia and other intrinsically safe approval power supply must Two–wire 4 to 20mA, user-selectable for linear or 5th order or two 2nd
not exceed 30VDC. order switching point selectable programmable polynomial output.

HART ® communication provides digital process variable (%, mA or

Ripple engineering units) superimposed on 4 to 20mA signal, with protocol
20mV max on a 250Ω load as per HART specifications based on Bell 202 FSK standard.

MINIMUM OPERATING VOLTAGES

Output current limits (to NAMUR standard)
no link on output indicator plugs Overload condition
- Lower limit: 3.8mA
with CoMeter indicator and HART communication
- Upper limit: 20.5mA
with ProMeter output indicator

Transmitter failure mode (to NAMUR standard)

with optional surge protection
The output signal can be user-selected to a value of 3.7 or 22mA on
with optional output analog indicator gross transmitter failure condition, detected by self-diagnostics.

In case of CPU failure the output is driven <3.7mA or >22mA.

with integral display

(volts)
10.5 10.7 12.3 12.5 13.3 15.3

Load limitations
4 to 20mA and HART total loop resistance :
Supply voltage – min. operating voltage (VDC)
R(kΩ) = –––––––––––––––––––––––––––––––––––––––
22.5
A minimum of 250Ω is required for HART communication.

Optional indicators
Output meter
CoMeter and Prometer LCD :
5-digit (±99999 counts) programmable with 7.6mm. high (3in),
7-segment numeric characters plus sign and digital point for digital
indication of output value in percentage, current or engineer unit;

10-segment bargraph display (10% per segment) for analog

indication of output in percentage;

7-digit with 6mm. high (2.3in), 14-segment alphanumeric

characters, for engineer units and configuration display

Analog : 36mm (1.4in) scale on 90°.

Integral display
LCD, 15 lines x 56 column dot matrix providing 2 lines indication as
– top: 5-digit (numeric) plus sign or 7-digit alphanumeric
– bottom: 7-digit alphanumeric
and additional 50-segment bargraph for indication of analog output
in percentage.

User-definable matrix display mode with HART communication:

– process variable in pressure unit or
– output signal as percentage, current or engineering units
Display also indicates in/out transfer function, static pressure, sensor
temperature and diagnostic messages and provides configuration
facilities.

4
2600T Pressure Transmitters
Model 264GS,

PROFIBUS PA output FOUNDATION Fieldbus output

Device type Device type
Pressure transmitter compliant to Profiles 3.0 Class A & B; ident. LINK MASTER DEVICE
number 052B HEX.
Link Active Scheduler (LAS) capability implemented.
Power supply
Power supply
The transmitter operates from 9 to 32VDC , polarity independent.
The transmitter operates from 9 to 32VDC, polarity independent.
For EEx ia approval power supply must not exceed 17.5VDC.
Intrinsic safety installation according to FISCO model. For EEx ia approval power supply must not exceed 24VDC (entity
certification) or 17.5VDC (FISCO certification), according to FF–816.
Current consumption
operating (quiescent): 10.5mA Current consumption

fault current limiting: 20mA max. operating (quiescent): 10.5mA

fault current limiting: 20mA max.
Output signal
Physical layer in compliance to IEC 1158–2/EN 61158–2 with Output signal
transmission to Manchester II modulation, at 31.25kbit/sec. Physical layer in compliance to IEC 1158–2/EN 61158–2 with
transmission to Manchester II modulation, at 31.25kbit/sec.
Output interface
PROFIBUS PA communication according to Profibus DP50170 Part 2/ Function blocks/execution period
DIN 19245 part 1–3.
2 enhanced Analog Input blocks/25ms max (each)
1 enhanced PID block/40ms max.
Output update time 1 standard ARitmetic block/25ms
25ms 1 standard Input Selector block/25ms
1 standard Control Selector block/25ms
Function blocks 1 standard Signal Characterization block/25ms
1 standard Integrator/Totalizer block/25ms
2 analog input, 1 transducer, 1 physical

Integral display
LCD, 15 lines x 56 column dot matrix providing 2 lines indication as Additional blocks
– top: 5-digit (numeric) plus sign or 7-digit alphanumeric 1 enhanced Resource block

– bottom: 7-digit alphanumeric 1 custom Pressure with calibration transducer block

and additional 50-segment bargraph for indication of output in 1 custom Advanced Diagnostics transducer block including Plugged
percentage of the analog input function block assigned to the primary Input Line Detection
variable.
1 custom Local Display transducer block
User-definable matrix display mode:
Number of link objects
– process variable in pressure units or 35

– primary variable in engineering units (output of transducer block) or Number of VCRs

– output as percentage or engineering units of analog input function 35
blocks
Output interface
Display also indicates diagnostic messages and provides
configuration facilities. FOUNDATION fieldbus digital communication protocol to standard H1,
Secondary variable, static pressure and sensor temperature can be compliant to specification V. 1.6; FF registration in progress.
read.
Integral display
Transmitter failure mode LCD, 15 lines x 56 column dot matrix providing 2 lines indication as
On gross transmitter failure condition, detected by self-diagnostics,
– top: 5-digit (numeric) plus sign or 7-digit alphanumeric
the output signal can be driven to defined conditions, selectable by the
user as safe, last valid or calculated value. If electronic failure or short – bottom: 7-digit alphanumeric
circuit occur the transmitter consumption is electronically limited at a
defined value (20mA approx), for safety of the network. and additional 50-segment bargraph for percentage indication of the
analog input function block output, assigned to the primary variable.

User-definable matrix display mode:

– process variable in pressure units or
– primary variable in engineering units (output of transducer block) or
– output as percentage or engineering units of one or more selected
function blocks

Display also indicates diagnostic messages. Secondary variable,

static pressure and sensor temperature can be read.

Transmitter failure mode

The output signal is "frozen" to the last valid value on gross transmitter
failure condition, detected by self-diagnostics which also indicate a
BAD conditions. If electronic failure or short circuit occur the transmitter
consumption is electronically limited at a defined value (20mA approx),
for safety of the network.

5
2600T Pressure Transmitters
Model 264GS,

Performance specifications Operating influences

Stated at reference condition to IEC 60770 ambient temperature of 20°C
(68°F), relative humidity of 65%, atmospheric pressure of 1013hPa Ambient temperature
(1013mbar), zero based range for transmitter with isolating diaphragms per 20K (36°F) change between the limits of –20°C to +65°C (–4 to
ceramic or Hastelloy and silicone oil fill and HART digital trim values equal +150°F) :
to 4–20mA span end points, in linear mode.
Sensor for TD
Unless otherwise specified, errors are quoted as % of span. Model Code up to
Some performance data are affected by the actual turndown (TD) as ratio F to V 15:1 ± (0.04% U RL + 0.065% span )
between Upper Range Limit (URL) and calibrated span. 2 6 4 GS
C 10:1 ± (0.06% U RL + 0.10% span )
IT IS RECOMMENDED TO SELECT THE TRANSMITTER SENSOR CODE
PROVIDING THE TURNDOWN VALUE AS LOWEST AS POSSIBLE TO F to U 10:1 ± (0.04% U RL + 0.065% span )
OPTIMIZE PERFORMANCE CHARACTERISTICS. 264A S
C 10:1 ± (0.065% U RL + 0.10% span )

Dynamic performance (according to IEC 61298–1 definition) Optional CoMeter and ProMeter ambient temperature
Dead time: 40ms Total reading error per 20K (36°F) change between the ambient limits
of –20 and +70°C (-4 and +158°F) :
Time constant (63.2% of total step change):
±0.15% of max span (16mA).
– 150 ms for all sensors
Response time (total) = dead time + time constant. Supply voltage
Within voltage/load specified limits the total effect is less than
Accuracy rating 0.005% of URL per volt.
% of calibrated span, including combined effects of terminal based
linearity, hysteresis and repeatability. Load
Within load/voltage specified limits the total effect is negligible.
For fieldbus versions SPAN refer to analog input function block outscale
range
Electromagnetic field
Model 264GS Total effect : less than 0.10% of span from 20 to 1000MHz and for
– ±0.075% for TD from 1:1 to 15:1 (10:1 for sensor C) field strengths up to 30V/m when tested with shielded conduit and
grounding, with or without meter.

URL Common mode interference

– ±0.005% x Span for TD from 15:1 to 60:1
No effect from 100Vrms @ 50Hz, or 50VDC
URL
– ±0.0075% x Span for TD from 10:1 to 30:1 for sensor C Mounting position
No effect
Model 264AS
Stability
– ±0.075% for TD from 1:1 to 10:1
±0.15% of URL over a five years period

URL Vibration effect

– ±0.0075% x Span for TD from 10:1 to 20:1
±0.10% of URL (according to IEC 61298–3)

6
2600T Pressure Transmitters
Model 264GS,

Physical Specification Optional extras

(Refer to ordering information sheets for variant availability related to
specific model or versions code) Mounting brackets
For 60mm. (2in) pipes or wall mounting.
Materials
Output indicator
Process isolating diaphragms (*)
plug-in rotatable type, LCD or analog.
Ceramic (Al203) gold-plated; Hastelloy C276™;
Supplemental customer tag
Hastelloy C276™ gold-plated.
AISI 316 ss tag screwed/fastened to the transmitter for customer's tag
Process connection (*) data up to a maximum of 20 characters and spaces on one line for tag
number and tag name, and up to a maximum of 3 spaced strings of 10
AISI 316 L ss; Hastelloy C276™. characters each for calibration details (lower and upper values plus
unit). Special typing evaluated on request for charges.
Gasket (only for sensor codes C, F) (*)
Viton™, Perfluoroelastomer, Perbunan (NBR). Surge protection (only as external unit for PROFIBUS PA and FF)

Sensor fill fluid Cleaning procedure for oxygen service (not for sensor V)
Silicone oil; inert fill (Carbon fluoride); white oil (FDA).
Test Certificates (test, design, calibration, material traceability)
Mounting bracket (**)
Tag and manual language
Zinc plated carbon steel with chrome passivation;
Communication connectors
AISI 316 L ss.
Process connections
Sensor housing
1
/2 – 14 NPT female or male; DIN EN837–1 G 1/2 B.
AISI 316 L ss.

Electronic housing and covers

Electrical connections
Barrel version Two 1/2 – 14 NPT or M20x1.5 or PG 13.5 or 1/ 2 GK threaded
conduit entries, direct on housing.
– Aluminium alloy with baked epoxy finish;
Special communication connector (on request)
– Copper-free content aluminium alloy with baked epoxy finish;
– HART : straight or angle Harting Han connector and one plug.
– AISI 316 L ss.
– FOUNDATION Fieldbus, PROFIBUS PA: M12x1 or 7/8.
Covers O-ring
Terminal block
Buna N.
HART version: three terminals for signal/external meter wiring up to
Local zero and span adjustments: 2.5mm2 (14AWG) and three connection points for test and
communication purposes.
Glass filled polycarbonate plastic (removable).
Fieldbus versions: two terminals for signal wiring (bus connection)
Tagging up to 2.5mm2 (14AWG)
AISI 316ss data plate attached to the electronics housing.
Grounding
Calibration Internal and external 6mm2 (10AWG) ground termination points are
provided.
Standard: at maximum span, zero based range, ambient temperature
and pressure;
Mounting position
Optional: at specified range and ambient conditions; or at operating
Transmitter can be mounted in any position.
temperature.
Electronics housing may be rotated to any position. A positive stop
prevents over travel.

Mass (without options)

1.2kg approx (3lb); add 1.5kg (3.4lb) for AISI housing.
Add 650g (1.5lb) for packing.

Packing
Carton 26 x 26 x 18cm approx (10 x 10 x 7in).

™ Hastelloy is a Cabot Corporation trademark

(*) Wetted parts of the transmitter.

(**) U-bolt material: AISI 400 ss; screws material: high-strength alloy steel or
AISI 316 ss.

7
2600T Pressure Transmitters
Model 264GS,

Configuration Transmitter with FOUNDATION Fieldbus

communication
Transmitter with HART communication and 4 to 20 mA
Transmitters are factory calibrated to customer's specified range.
Standard configuration Calibrated range and tag number are stamped on the tag plate. If a
Transmitters are factory calibrated to customer's specified range. calibration range and tag data are not specified, the transmitter will be
Calibrated range and tag number are stamped on the tag plate. If a supplied with the plate left blank and the analog input function block FB1
calibration range and tag data are not specified, the transmitter will be is configured as follows:
supplied with the plate left blank and configured as follows: Measure ProfilePressure
Engineering UnitkPa Engineering UnitkPa
4 mAZero Output scale 0%Lower Range Limit (LRL)
20 mAUpper Range Limit (URL) Output scale 100%Upper Range Limit (URL)
OutputLinear OutputLinear
Damping1 sec. Hi-Hi LimitUpper Range Limit (URL)
Transmitter failure modeUpscale Hi Limit :Upper Range Limit (URL)
Software tag (8 characters max) Blank Low LimitLower Range Limit (LRL)
Optional LCD indicator/display 0 to 100.0% linear Low-Low LimitLower Range Limit (LRL)
Any or all the above configurable parameters, including Lower range–value Limits hysteresis0.5% of output scale
and Upper range-value which must be the same unit of measure, can be PV filter time0 sec.
easily changed using the HART hand–held communicator or by a PC Tag32 alphanumeric characters
running the configuration software SMART VISION with DTM for 2600T. The analog input function block FB2 is configured for the sensor tempe-
The transmitter database is customized with specified flange type and rature measured in °Χ. Any or all the above configurable parameters,
material, O–ring and drain/vent materials and meter code option. including the range values, can be changed using any host compliant to
Custom configuration (option) FOUNDATION fieldbus. The transmitter database is customized with
The following data may be specified in addition to the standard specified flange type and material, O–ring and drain/vent materials and
configuration parameters: meter code option.
Descriptor16 alphanumeric characters
Message32 alphanumeric characters
DateDay, month, year
For any protocol available engineering units of pressure measure are :
Pa, kPa, MPa
inH2O@4°C, mmH2O@4°C, psi
inH2O@20°C, ftH2O@20°C, mmH2O@20°C
inHg, mmHg, Torr
Transmitter with PROFIBUS PA communication g/cm2, kg/cm2, atm
Transmitters are factory calibrated to customer's specified range. mbar, bar
Calibrated range and tag number are stamped on the tag plate. If a
calibration range and tag data are not specified, the transmitter will be
supplied with the plate left blank and configured as follows:
Measure ProfilePressure
Engineering UnitkPa
Output scale 0%Lower Range Limit (LRL)
Output scale 100%Upper Range Limit (URL)
OutputLinear
Hi-Hi LimitUpper Range Limit (URL)
Hi LimitUpper Range Limit (URL)
Low LimitLower Range Limit (LRL)
Low-Low LimitLower Range Limit (LRL)
Limits hysteresis0.5% of output scale
PV filter0 sec.
Address (settable by local key) 126
Tag32 alphanumeric characters
Any or all the above configurable parameters, including Lower range-value
and Upper range–value which must be the same unit of measure, can be
easily changed by a PC running the configuration software SMART VISION
with DTM for 2600T.
The transmitter database is customized with specified flange type and
material, O–ring and drain/vent materials and meter code option.
Custom configuration (option)
The following data may be specified in addition to the standard
configuration parameters:
Descriptor32 alphanumeric characters
Message32 alphanumeric characters
DateDay, month, year

8
2600T Pressure Transmitters
Model 264GS,

MOUNTING DIMENSIONS (not for construction unless certified) - dimensions in mm (in

Transmitter with barrel housing on bracket for 60mm (2in) pipe mounting

Adjustments Identification tag

127 (5.00) Electrical
26 (1.02) 36 (1.42) connections
17 (0.67) 17 (0.67) 86 (3.39)
Min. clearance
to remove Certification
the cover label
NSO T SOI TS AL I V US TEECU TSI

L ES N
100 (3.94) C IO
Electronic Covers locking
CI R I R
CU
NS

!
side Terminal screw AN
ET QU GARD
ERKE L
E'T H E N
CER LE BIEN FUVECO VER TI GH
side W
RME P COTE

Integral display
housing
Output meter
housing

50 (1.97)

CH27
56 (2.20)
70 (2.75)
135 (5.31)

1
/2 – 14 NPT female connection

Adjustments Identification tag

127 (5.00)
26 (1.02) 36 (1.42) Electrical
17 (0.67) 17 (0.67) connections
Min. clearance
to remove Certification 86 (3.39)
the cover label

NSO T SOI TS AL I V US TEECU TSI

Electronic 100 (3.94)

L ES N
C
side CI R I R
IO
Terminal Covers locking CU
NS

!
side screw AN
ET QU GARD
ERKE L
E'T H E N
Integral display W CER LE BIEN FUVECO VER TI GH
RME P COTE

housing
Output meter
housing

58 (2.28)

56 (2.20) CH22
G 1/2 B
135 (5.31)

DIN–EN837–1 G 1/2 B connection

9
2600T Pressure Transmitters
Model 264GS, 264AS SS/264GS/AS_6

Adjustments Identification tag Electrical

127 (5.00) connections
26 (1.02) 36 (1.42)
17 (0.67) 17 (0.67) 86 (3.39)
Min. clearance Certification
to remove label
NSO T SOI TS AL I V US TEECU TSI
the cover
Covers locking L ES N
100 (3.94) screw
C
CI R I R
IO
NS
Electronic CU
ET QU !
side Terminal AN
E'T H E N
GARD
ERKE L
CER LE BIEN FUVECO VER TI GH RME
side W
P COTE

Integral display
housing
Output meter
housing

55 (2.17)

56 (2.20) CH22
135 (5.31)

1
/2 – 14 NPT male connection

10
2600T Pressure Transmitters
Model 264GS,

Electrical connections
HART Version

Internal ground
termination point
Remote
indicator
-
6 7 8
5 9
4
23 40 60 10

M+
0 20 80
% 10
0
0
Kent-Taylor

-
Line load M
+
250 ohm min
+
+
Power GND
TEST COMM
source
External ground
- - 691HT

termination point
F1 F2 F3 F4

6 5 4
PV

SERIALLINK

1
-
REVIEW CONF

Optional 7
- +
TRIM

ABC DEF GHI

1 2 3
8 2 3
JKL

4
MNO

5
PQ R

6
Test points
Receiver ST U

7
VWX

8
YZ#

9 Hand-held 4 to 20mA Harting pin (male)

@% &/
0
+
-
communicator + identification

HART hand-held communicator may be connected at any wiring termination point in the loop, providing the minimum resistance
is 250 ohm. If this is less than 250 ohm, additional resistance should be added to allow communications

FIELDBUS Versions

7/8” connector Internal ground

termination point
1 3

2 4

M12 x 1 connector
Fieldbus line
2
(polarity independent)

3 1 BUS CONNECTIONS

External ground
termination point
PIN (male) IDENTIFICATION
FOUNDATION PROFIBUS
FieldbusPA
1FF-PA+
2FF+GROUND
3SHIELDPA–
4GROUNDSHIELD

CONNECTOR IS SUPPLIED LOOSE WITHOUT MATING FEMALE PLUG

11
2600T Pressure Transmitters
Model 264GS,

BASIC ORDERING INFORMATION model 264GS Gauge Pressure Transmitter

Select one character or set of characters from each category and specify complete catalog number.
Refer to additional ordering information code and specify one or more codes for each transmitter if additional options are required.

BASE MODEL – 1st to 5th characters 2 6 4 G S X X X X X X

Gauge Pressure Transmitter – BASE ACCURACY 0.075%

SENSOR - Span limits – 6th character

0.2 and 6kPa2 and 60mbar0.8 and 24inH2O C
0.4 and 40kPa4 and 400mbar1.6 and 160inH2O F
2.5 and 250kPa25 and 2500mbar10 and 1000inH2O L
30 and 3000kPa0.3 and 30bar4.35 and 435psi U
100 and 10000kPa1 and 100bar14.5 and 1450psi R
600 and 60000 kPa6 and 600bar87 and 8700psi V
Diaphragm material / Fill fluid (wetted parts) – 7th character
Hastelloy C276™Silicone oil
Hastelloy C276™ gold-platedSilicone oil
Hastelloy C276™Inert fluid (Note 2) NACE K
Hastelloy C276™ gold-platedInert fluid (Note 2) NACE G
Hastelloy C276™White oil (FDA) (Notes 1, 2) NACE F
Hastelloy C276™ gold-platedWhite oil (FDA) (Notes 1, 2) NACE E
CeramicNo filling (Note 2) NACE Z
Process connection material (wetted parts) – 8th character (Note 2) NACE 1
(Note 3) NACE J

1
AISI 316 L ss /2 – 14 NPT female NACE B
AISI 316 L ss / – 14 NPT male
1 2 NACE T
AISI 316 L ss DIN EN837– 1 G 1/2 B NACE P
Hastelloy C276™ 1/2 – 14 NPT female NACE E
Hastelloy C276™ 1/2 – 14 NPT male NACE K
Hastelloy C276™ DIN EN837– 1 G 1/2 B NACE D
Gasket – 9th character

Viton™ (Notes 1, 3) NACE 5

Perfluoroelastomer (MWP=0.6MPa) (Note 3) NACE 6
Perbunan (Note 3) NACE 8
None (Note 2) NACE N
Housing material and electrical connection – 10h character

1
Aluminium alloy (Barrel version) /2 – 14 NPT A
Aluminium alloy (Barrel version) M20 x 1.5 (CM 20) B
Aluminium alloy (Barrel version) Pg 13.5 D
Aluminium alloy (Barrel version) 1/2 GK C
Aluminium alloy (Barrel version) Harting Han connector E
Aluminium alloy (Barrel version) Fieldbus connector (general purpose only) (Note 4) G
Aluminium alloy copper-free (Barrel version) 1/2 – 14 NPT (general purpose only) (Note 4) H
Aluminium alloy copper-free (Barrel version) M20 x 1.5 (CM 20) L
Aluminium alloy copper-free (Barrel version) Pg 13.5 N
Aluminium alloy copper-free (Barrel version) 1/2 GK M
Aluminium alloy copper-free (Barrel version) Harting Han connector P
Aluminium alloy copper-free (Barrel version) Fieldbus connector R
AISI 316 L ss (Barrel version) 1/2 – 14 NPT (general purpose only) (Note 4) S
AISI 316 L ss (Barrel version) M20 x 1.5 (CM20) (general purpose only) (Note 4) T
AISI 316 L ss (Barrel version) Pg 13.5 V
AISI 316 L ss (Barrel version) 1/2 GK U
AISI 316 L ss (Barrel version) Fieldbus connector Z

(general purpose only) (Note 4)

th
Output/Additional options – 11 character
HART digital communication and 4 to 20mA No additional options (Note 5, 6) H
HART digital communication and 4 to 20mA Options requested (to be ordered by "Additional ordering code") (Note 5) 1
PROFIBUS PA No additional options (Note 5, 6) P
PROFIBUS PA Options requested (to be ordered by "Additional ordering code") (Note 6) 2
FOUNDATION Fieldbus No additional options (Note 5, 6) F
FOUNDATION Fieldbus Options requested (to be ordered by "Additional ordering code") (Note 6) 3

12
2600T Pressure Transmitters
Model 264GS,

ADDITIONAL ORDERING INFORMATION for model 264GS

Add one or more 2-digit code(s) after the basic ordering information to select all required options

XX XX XX XX XX XX XX XX XX XX XX XX XX
Electrical certification
ATEX Group II Category 1 GD – Intrinsic Safety EEx ia E1
ATEX Group II Category 1/2 GD – Flameproof EEx d (Note 2) E2
ATEX Group II Category 3 GD – Type of protection "N" EEx nL design compliance (Note 7) E3
Canadian Standard Association (CSA) (only 1/2– 14NPT, M20 and Pg 13.5 electrical connection) - (Note 8) E4
Standards Australia SAA (Not Ex d; Not Ex ia and Ex n for PROFIBUS PA and FOUNDATION Fieldbus) E5
Factory Mutual (FM) approval (only with 1/2– 14NPT, M20 and Pg 13.5 electrical connection) - (Note 8) E6
Combined ATEX - Intrinsic Safety and Flameproof (Note 2) E7
Combined ATEX, FM and CSA (only with 1/2– 14NPT, M20 and Pg 13.5 electrical connection) (Notes 7,8) EN
NEPSI (China) - Intrinsic Safety Ex ia EY
NEPSI (China) - Flameproof Ex d (Note 2) EZ
GOST (Russia) EEx ia W1
GOST (Russia) EEx d (Note 2) W2
GOST (Kazakhstan) EEx ia W3
GOST (Kazakhstan) EEx d (Note 2) W4
Inmetro (Brazil) EEx ia W5
Inmetro (Brazil) EEx d (Note 2) W6
Inmetro (Brazil) EEx nL W7
Metrologic (Russia) WC
Metrologic (Kazakhstan) WD
Output meter

ProMeter, Standard calibration (Note 7) D1

ProMeter, Special calibration (Note 7) D2
Analog output indicator linear 0– 100% scale (Note 7) D3
Analog output indicator, special graduation (to be specified for linear scale) (Note 7) D5
Programmable signal meter and HART configurator (CoMeter) (Note 7) D7
Programmable signal meter and HART configurator (CoMeter – customer configuration) (Note 7) D8

Integral LCD
Digital LCD integral display L1

Mounting bracket (shape and material)

For pipe mounting (Not suitable for AISI housing) Carbon steel B1
For pipe mounting AISI 316 L ss B2
Surge
Surge/Transient Protector (Internal for HART / 4-20mA)
Surge/Transient Protector (External supplied loose for PROFIBUS PA and FOUNDATION Fieldbus only S1
suitable with 1/2– 14NPT and M20 electrical connection and with ATEX, FM and CSA certifications, no DUST)

Operating manual
German M1
Italian M2
Spanish M3
French M4

Labels & tag language

German T1
Italian T2
Spanish T3
French T4

Additional tag plate

Laser printing of tag on stainless steel plate I2

Configuration
Standard – Pressure = inH2O/psi at 20° C; Temperature = deg. F N2
Standard – Pressure = inH2O/psi at 4° C; Temperature = deg. F N3
Standard – Pressure = inH2O/psi at 20° C; Temperature = deg.C N4
Standard – Pressure = inH2O/psi at 4° C; Temperature = deg. C N5
Custom N6

Preparation procedure
Oxygen service cleaning (only available with inert fill and Viton gasket) – Pmax =21MPa/210bar/3045psi; Tmax = 60° C/140° F P1

Certificates
Inspection certificate EN 10204– 3.1 of calibration (9-point) C1
Certificate of compliance with the order EN 10204– 2.1 of instrument design C6

Material traceability
Certificate of compliance with the order EN 10204– 2.1 of process wetted parts H1
Inspection certificate EN 10204– 3.1 of process wetted parts H3
Connector
Fieldbus 7/8 (Recommended for FOUNDATION Fieldbus) - (supplied loose without mating female plug) (Notes 6, 9) U1
Fieldbus M12x1 (Recommended for PROFIBUS PA) - (supplied loose without mating female plug) (Notes 6, 9) U2
Harting Han – straight entry (Notes 5, 9) U3
Harting Han – angle entry (Notes 5, 9) U4

13
2600T Pressure Transmitters
Model 264GS,

Note 1: Suitable for oxygen service

Note 2: Not available with Sensor code C, F
Note 3: Not available with Sensor code L, U, R, V
Note 4: Select type in additional ordering code
Note 5: Not available with Electronic Housing code Z, R, G
Note 6: Not available with Electronic Housing code P, E
Note 7: Not available with PROFIBUS PA and FF output code 2 or 3
Note 8: Not Ex d for sensor code C, F
Note 9: Not available with Electronic housing code U, S, T, V, H, M, L, N, D, C, A, B

™ Hastelloy is a Cabot Corporation trademark

™ Viton is a Dupont de Nemour trademark

Standard delivery items (can be differently specified by additional ordering code)

– General purpose (no electrical certification)
– No meter/display, no mounting bracket, no surge protection
– English manual and labels
– Configuration with kPa and deg. C units
– No test, inspection or material traceability certificates

THE SELECTION OF SUITABLE WETTED PARTS AND FILLING FLUID FOR COMPATIBILITY WITH THE PROCESS MEDIA IS A CUSTOMER'S
RESPONSIBILITY, IF NOT OTHERWISE NOTIFIED BEFORE MANUFACTURING.

14