Instruction Manual Powcom™ 5.2.X: Powering Technology

P O W E R I N G T E C H N O L O G Y
INSTRUCTION MANUAL
PowCom™ 5.2.x
www.unipowerco.com
Manual No. POWCOM-7 © 2018 UNIPOWER LLC

powcom-man-rev7-0318.indd All Rights Reserved
UNIPOWER LLC • 3900 Coral Ridge Drive, Coral Springs, Florida 33065, USA • sales@unipowerco.com
North America: +1 954-346-2442 • Europe: +44 1903 768200
Copyright © 1999-2018 UNIPOWER LLC

All Rights Reserved
Restricted Rights Legend:
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in
subparagraph © (1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS
252.227-7013 or subparagraphs © (1) and (2) of Commercial Computer Software - Restricted
Rights at 48 CFR 52.227-19, as applicable.
For Contact Information, please go to http://www.unipowerco.com/contact/
Refer to the UNIPOWER License Agreement in this package before installing or using this product.
Unless specifically noted, all addresses, data characters and persons referenced herein, and all
examples involving names of companies and products, are fictitious examples and are designed
solely to illustrate the use of UNIPOWER products.
Product names, logos, brands, and other trademarks featured or referred to within this product
manual are the property of their respective trademark holders. These trademark holders are not
affiliated with UNIPOWER LLC or our products. They do not sponsor or endorse our products.
LIMITATIONS AND AUTHORIZATIONS FOR USE AND PERMITTED APPLICATIONS
UNIPOWER’s products are not designed, intended for use in, or authorized for use as critical
components in, human life support systems/equipment, equipment used in hazardous environments,
or equipment used in nuclear control equipment or systems. Any such use requires the prior
express written consent of an authorized executive officer of UNIPOWER LLC, which consent
may be withheld by UNIPOWER LLC in its sole discretion. Users assume all risk and liability for,
and agree to indemnify and defend UNIPOWER from and against any claims for personal injury
(including death) or property damage resulting from any such use or application which is made in
the absence of such prior express written consent.
If you find errors or problems with this documentation, please notify UNIPOWER. UNIPOWER
does not guarantee that this document is error-free. The information in this document is subject to
change without notice.
Manual No. POWCOM-7 2 powcom-man-rev7-0318.indd

Contents
Chapter 1 - General Introduction..................................................................................................6
1.1 General Introduction.................................................................................................................6
1.2 Hardware Requirements............................................................................................................6
1.3 Feedback & Support..................................................................................................................6
Chapter 2 - Installation..................................................................................................................7
2.1 Installation.......
.........................................................................................................................7
2.2 Compatibility with older versions of PowCom™.....................................................................8
2.4 Null-modem Cable....................................................................................................................8
2.4 USB Cable.................................................................................................................................8
Chapter 3 - Main Window............................................................................................................10
3.1 Main Window..........................................................................................................................10
3.1.1 Module Information....................................................................................................13
Chapter 4 - Main Menu................................................................................................................17
4.1 Communication menu.............................................................................................................17
4.1.1 Call via modem...........................................................................................................17
4.1.1.1 Phone list........................................................................................................17
4.1.1.2 Edit.................................................................................................................18
4.1.1.3 Password........................................................................................................18
4.1.1.4 Quick search...................................................................................................18
4.1.1.5 Calling............................................................................................................18
4.1.1.6 Modem initialization......................................................................................18
4.1.2 USB communication...................................................................................................19
4.1.3 Direct communication.................................................................................................19
4.1.4 Network connection....................................................................................................19
4.1.5 Com port setup............................................................................................................20
4.1.6 Properties....................................................................................................................21
4.1.6.1 Message timeout............................................................................................21
4.1.6.2 Dial up timeout..............................................................................................21

4.2 Supervision menu....................................................................................................................21

4.2.1 Set parameters.............................................................................................................21
4.2.1.1 Adjust Limits.................................................................................................22
4.2.1.2 Battery settings...............................................................................................25
4.2.1.3 Custom Boost Settings...................................................................................27
4.2.2 Set Extra Parameters...................................................................................................28
4.2.3 Program version..........................................................................................................29
4.2.4 Set date and time.........................................................................................................29
4.2.5 Set installation data.....................................................................................................29
4.2.7 Change user password................................................................................................29
4.2.8 Transfer test data.........................................................................................................30
4.2.9 Get all test data...........................................................................................................30
4.2.10 Get battery log............................................................................................................30
4.2.11 System logs.................................................................................................................31
4.2.12 Alarm history..............................................................................................................34
4.2.13 Alarm information......................................................................................................34
4.2.14 Alarm dial back...........................................................................................................34
4.2.15 Set network address....................................................................................................35
4.2.16 TCP/IP settings...........................................................................................................35
4.2.17 Inventory.....................................................................................................................36
4.3 Utilities menu..........................................................................................................................37
4.3.1 Log data......................................................................................................................37
4.3.2 Inventory Log.............................................................................................................37
4.3.3 View test data..............................................................................................................38
4.3.4 View parameter file.....................................................................................................39
4.3.5 Update configuration...................................................................................................40
4.3.6 Modify configuration..................................................................................................41
4.3.7 Configuration wizard..................................................................................................41
4.3.8 Button Bar...................................................................................................................41
4.4 Tools Menu..............................................................................................................................42
4.4.1 Download SD card......................................................................................................42

FIGURES
Figure 2-1 Language Selection...............................................................................................7
Figure 2-2 Null-modem cable................................................................................................8
Figure 2-3 USB cable.............................................................................................................9
Figure 3-1 Main Window.....................................................................................................10
Figure 3-2a Main Window with Displayed Modules.............................................................13
Figure 3-2b Main Window with Displayed Modules with 4x64 Multiplexer........................14
Figure 3-3a Main Window with Displayed Modules.............................................................15
Figure 3-3b Main Window with Displayed Modules with 4x64 Multiplexer........................15
Figure 3-4 Module Info........................................................................................................16
Figure 4-1 Communication menu.........................................................................................17
Figure 4-2 Example of a phone list......................................................................................17
Figure 4-3 Com port setup....................................................................................................20
Figure 4-4 Adjust limits window..........................................................................................22
Figure 4-5 Battery Settings Window....................................................................................25
Figure 4-6 Custom Boost Settings Window.........................................................................27
Figure 4-7 Set Extra Parameters...........................................................................................28
Figure 4-8 Installation data...................................................................................................29
Figure 4-9 Battery Log.........................................................................................................30
Figure 4-10 Alarm History.....................................................................................................31
Figure 4-11 Inventory.............................................................................................................31
Figure 4-12 Peak Load...........................................................................................................32
Figure 4-13 Site Data..............................................................................................................32
Figure 4-14 Maintenance and Service....................................................................................33
Figure 4-15 Statistical Data....................................................................................................33
Figure 4-16 Alarm History.....................................................................................................34
Figure 4-17 Dial Back Control...............................................................................................35
Figure 4-18a Inventory.............................................................................................................36
Figure 4-18b Inventory with 4x64 Multiplexer........................................................................37
Figure 4-19 Log Data.............................................................................................................37
Figure 4-20 View Test Data....................................................................................................38
Figure 4-21 View Parameter File...........................................................................................39
Figure 4-22 Update Configuration..........................................................................................40
Figure 4-23 Download SD Card.............................................................................................42

Chapter 1 - General Introduction
1.1 General Introduction

PowCom™ software is a Windows based program that communicates with and controls
UNIPOWER Aspiro and Guardian rectifiers and supervision systems. The software allows
a user to access the system from a remote location using a graphic user interface to perform
the same functions that are available on the controller (PCU/PCS/GMC/PCC/ACC/ACX
Advanced).
Some of these functions include:
• Viewing battery test data.
• Displaying battery discharge curves.
• A database function for saving battery test information.
• Context sensitive help. Pressing the F1 key opens a help menu that is sensitive to the
current active window.
• Site installation information.
• Devices operating status.
• System data logging and collecting
NOTE Some functions described in this chapter may not be available to all systems due
to different hardware configurations.
1.2 Hardware Requirements

PowCom™ software requires a computer with Microsoft Windows98SE or later with at least
one serial port available. A modem/null-modem cable/USB is used to connect from the serial
port on the computer to the external hardware.
The modem must be Hayes compatible and communicate on one of the following baud rates:
2400, 4800, 9600 and 38400. The baud rate must be at least as high as the one in the power
system.
PowCom™ will automatically adjust itself to the baud rate in the power system if it is lower
than the one in PowCom™. Therefore, it is possible to call a system that has a modem with
the baud rate set to 2400, with a 9600 baud modem. However, the power system cannot be
adjusted to a lower baud rate. Therefore, it is impossible to call a system which has a modem
with a baud rate of 9600, and which is adjusted to 9600 baud, with a 2400 baud modem.
1.3 Feedback & Support

For technical support or feedback, please visit http://www.unipowerco.com/contact/ and
select Customer “Support/Repairs” and then “Customer Service”.
Alternatively, email: sales@unipowerco.com
Chapter 2 - Installation
2.1 Installation
1. Download the latest PowCom™ setup file of your choice from the the controller landing
page on the UNIPOWER web site:
• PCC Controller
• ACX Advanced Controller
2. The downloaded program works in read-only mode until the license key has been entered.
3. Obtain a license key from your UNIPOWER sales associate. Note that your company may
have a company license with a license number distributed internally. It is recommended
to check this before contacting UNIPOWER.
4. After extracting the zip file run setup.exe.
NOTE Administrator rights for Win2000, XP, Vista,Windows7 or later are required.
5. The program will prompt for an installation directory. Select the directory for installation.
The default directory is:
C:\Program Files (x86)\UNIPOWER\PowCom
Press “Next” after entering the directory.
NOTE In most cases warnings are caused by DLL files in the WINDOWS/SYSTEM
directory being newer than the version on the installation disk but should not cause a
problem with the system.
6. PowCom™ supports multiple languages. The preferred language can be selected in the
language selection page, see Figure 2-1.
Figure 2-1 Language Selection

2.2 Compatibility with older versions of PowCom™

Data files (phone book, tests data) from previous versions of the PowCom™ can be used in
this version. Copy these files to the PowCom™ data folder. The path to this folder is:
C:\Documents and Settings\All Users\Application Data\PowCom
(Windows 2000/Windows XP)
or:
C:\Users\<username>\AppData\Roaming\UNIPOWER\PowCom
(Windows Vista/Windows 7)
or subfolder Data of the PowCom4 application folder:
C:\Program Files\PowCom\Data
(Windows 98/Windows Me)
For modem installation, please consult the system documentation.
NOTE Prior to release 5.00.05 PowCom™ default file paths used ‘Power-One’ in place
of ‘UNIPOWER’.
2.4 Null-modem Cable

If a null-modem cable is used to communicate directly with a control unit without using
a modem, select Communication / Direct communication. The baud rate for both,
PowCom™ and the control unit should be the same. If the baud rate for PowCom™ and the
control unit are different, it is impossible to make a connection.
Connect the cable to the 9-pin plugs as follows:
2 2
3 3
5 5
Figure 2-2 Null-modem cable
2.4 USB Cable

The ACX controller does not have a DB9 connector for direct communication but it has USB
connector. A standard USB AM-BM cable can be used for connection, see figure 2-3. For
some systems it is also possible to use a serial port (RJ-45) on the internal connection board.

When the ACX is connected to the PC, a virtual COM port is created and should be set as a
communicator port in PowCom™. For port setting see Com port setup, section 4.1.5.
NOTE PowCom™ has to be installed before the ACX is connected for the first time,
otherwise Windows does not recognize the ACX correctly.
Standard A plug Standard B plug
Figure 2-3 USB cable

Chapter 3 - Main Window
3.1 Main Window

When connected to the system, the PowCom™ main window displays various information
about the system. The information may differ depending on the particular system, but the
key parameters like system voltage and battery current are usually displayed here. The main
part of the window is occupied by a diagram that shows basic information.
H D E
I G
C B
F
J
Figure 3-1 Main Window
NOTE The information displayed when clicking on the icons vary depending on the type
of the controller and also on the power system setup.
A. Rectifier Icon
The rectifier icon displays the rectifier current. When this icon is clicked on, module
information is displayed at the bottom left side of the main window. (See A in Figure 3-1.)
For more information see Module Information in section 3.1.1.

CHAPTER 3
B. Breaker Icon
The value next to the Breaker icon displays the system voltage and load current.
For a system controlled by a PCS it has individual current measurements:
When this icon is clicked on, system specific information is displayed. On PCS system that
have distribution with individual current measurement it shows control that displays current
values and allows settings of the individual high current alarms. If the limit checkbox is not
checked the limit is inactive. Setting the limit to 0 is the same as deactivating it. (See B in
Figure 3-1.)
C. Battery Icon
The value next to this icon displays the battery current. (If the current is negative the battery
is discharged.) When this icon is clicked on battery symmetry information is shown if the
system is set up to measure it. If a battery temperature probe is installed, battery temperature
information is also displayed here. (See C in Figure 3-1.)
NOTE With the ACX controller, if the battery capacity is set, a capacity indicator is
displayed below the battery icon. However, as not all information from the ACX is available
for the PowCom™ software, the remaining capacity shown in PowCom™ can differ from
the information shown on the ACX display.
Symmetry voltage
Symmetry voltage lists the measured values of the symmetry voltages. If the battery/batteries
contain 18 cells, one of the measurements for each battery will be 0.00V.
A Red icon signifies an alarm appertaining to that particular icon.

D. Inverter Icon
This icon displays the current of the inverter. When this icon is clicked on, module information
is displayed at the bottom left side of the main window. (See D in Figure 3-1.)
E. Converter Icon
This icon displays the current of the DC converter. When this icon is clicked on, module
information is displayed in the bottom left side of the main window. (See E in Figure 3-1.)
F. Alarm relay
The alarm relay icon is displayed in blue and indicates the alarm condition for a specific
relay. A Red icon signals an alarm condition. (See F in Figure 3-1.)
G. Alarm Information
Details of signaled alarm are shown on the right side of the main window. (See G in Figure
3-1.) If the main window is small and the Alarm Information is not displayed the Alarm icon
goes active.
Selecting the LIVE or LATCHED tab will display current and previously recorded intermittent
alarms respectively.
NOTE The LATCHED tab will only be displayed when connected to a controller supporting
this feature, e.g. ACX Advanced with firmware version 2.20 or later.

H. External Measurements
This button is available only if one or more external measurements are set in the system. If
it is clicked on, a window with detailed information about external measurements (that are
system specific, i.e. they are not standard measurements) appears. These measurements and
their descriptions are programmed in the configuration of the system. (See H in Figure 3-1.)
I. Operation mode
A text field indicates the charging status of the system; NORMAL, BOOST, TEST, SPARE,
etc. (See I in Figure 3-1.)
J. Graphic chart
The Graphic chart in the bottom right corner displays value history for the selected interval
(time on the x-axis; voltage, current or temperature on the y-axis). It can be changed by a
right mouse click on the chart. Values displayed at the icons can be displayed in the graph,
when clicked on them. A right click changes the source for a blue line, a left click changes
the source for a green line. (See J in Figure 3-1.)
3.1.1 Module Information
Figure 3-2a Main Window with Displayed Modules

Figure 3-2b Main Window with Displayed Modules with 4x64 Multiplexer
Click on the rectifier / converter / inverter icon and information regarding the installed
modules appear on the left bottom side.
A blue icon indicates the module is working properly. A red icon indicates the module is
in an alarm condition. A gray icon indicates the module is not installed. An orange icon
indicates the module is in energy save mode (ACC & ACX Advanced only).
If any module icon is clicked, detailed module data is displayed at the bottom of the window,
Figure 3-3 on page 3-6.
NOTE When the 4x64 Multiplexer is installed it is necessary to select a channel before
selecting a particular module. See figure 3-2.
Module data
The displayed information depends on the system.
The scrollbar at the bottom of the window is used to select the module number for which the
data is displayed. If another module is selected with the scrollbar the information regarding
the selected module appear on the screen after approximately one second.

Figure 3-3a Main Window with Displayed Modules
Figure 3-3b Main Window with Displayed Modules with 4x64 Multiplexer
With PCS and ACX controllers installed, when the small rectifier icon in the bottom left
corner is clicked, a dialog box with additional information (serial number, revision, etc.)
opens. See Figure 3-4.

Figure 3-4 Module Info
If the system configuration allows it, modules can be turned on/off directly from the screen
of the ACX controller. (See Adjust limits -> Module ON/OFF.)
NOTE Configuration allows manual or automatic module on/off. If the manual or

automatic function is allowed, the module power state can be controlled from the controller.
If the automatic function is allowed and turned on, it overrides the manual setting. During
manual/automatic turn off the mean current value is invalid and the current share among
the modules does not run in a standard way. To obtain a correct value it is necessary to
remove the module from the slot.

Chapter 4 - Main Menu
4.1 Communication menu
Figure 4-1 Communication menu
4.1.1 Call via modem

4.1.1.1 Phone list
To create a telephone list press “New/Phone list” and select a file. Type a file name and
Open. Several telephone lists can be created, each of them can be protected with a password.
To enter a contact to the list press “Edit”. Fill in the name, telephone number, baud rate and
callback if needed.
If no baud rate is entered, use 9600. If the modem you want to communicate with is adjusted
to a lower speed, the program will automatically adjust the speed when contact is achieved.
If a new contact needs to be added click on the blank line at the bottom of the telephone list.
Select “Edit” and enter required information.
The telephone list is sorted in alphabetical order automatically when a number is added to
the list.
Figure 4-2 Example of a phone list

4.1.1.2 Edit
To edit the telephone list, highlight a line and select “Edit”. Make necessary changes and
press OK.
To delete a line in the telephone list, select a line and press “Delete”.
To change the telephone list, press “New/Phone list” and select the file. To create a new list,
type a new file name, and the file will be created.
To change the password for the active telephone list, press “New password”. Enter old
password. Then, fill in a new password twice to ensure correct spelling. (The password can
contain all numbers and letters regardless of the letter case used.)
4.1.1.3 Password
Once the connection is made, a system password needs to be entered. For remotely controlled
systems the default password is 1234.
Some systems also require a password to accept parameter updates.
4.1.1.4 Quick search
If the telephone list is too long a Quick Search field may be used. Start typing a required
name and the first item in the list matching the typed name will be highlighted. If “Enter” is
pressed, PowCom™ starts automatically dialing the number.
An already existing list made with an earlier versions of PowCom™ can be sorted out by
selecting an item from the list. Press “Edit”. Without changing anything press OK in the
window that pops up. The list is now sorted. PowCom™ sorts out the list automatically
when changes have been made.
4.1.1.5 Calling
This window is displayed when the connection is made via modem. Messages from the
modem are shown in the text box.
To dial-up, select the number from the list and press “Call”.
If the list does not contain the number you want to call, press “Call other number” and enter
the telephone number, baud rate and callback, if needed, and press OK.
If the modem cannot establish the connection, an error message, such as: NO CARRIER,
BUSY, NO DIAL TONE, NO CONNECTION or CANNOT CONNECT TO THE MODEM
will be generated. In such case PowCom™ does not hang up. It is necessary to press “Cancel
call” to hang up.
4.1.1.6 Modem initialisation
To change the initialisation string for the modem, press “Modem setup” and enter the string.

NOTE Switch data compression off, select direct asynchronous communication, set the
terminal speed to follow the line speed, select no hand shake. For some modems these
parameters are set by default. For high speed modems data compression (v42/MNP) have
to be usually switched off.
Examples of suitable initialization strings for some modems:
Modem Type Initialization String

US Robotics Sportster 14400 AT&K0
Lasat Unique 14400 AT&Q0&K0
UCOM Fastlink 14400 AT&Q0
HIDEM 14400 fax AT%C0\N1
HANDY 144 CC AT&F&C1|&Q0&K0
XLINK 28800 AT%C0\N1 (Rockwell chipset)
4.1.2 USB communication (ACX Advanced only)

The ACX Advanced Controller is designed to USB HID class specifications and expected to
work as a USB-compatible device.
4.1.3 Direct communication

Direct communication is used to access the system, which is directly connected to the
controller, using a null-modem cable/USB cable. It is important to set com-port and baud-
rate correctly before selecting “Direct Communication”.
When the connection is made the installation information of the system is shown in a dialog
window and the system password has to be entered.
4.1.4 Network connection

Network Connection enables to establish a connection to the system with the PNI (Power
Network Interface). The PNI contains a server that allows connection with PowCom™.
It is also possible to connect through a TCP/IP server that works as a link to a network of
rectifier systems connected to that server. To use this a server program must be running on
this computer or on another computer reachable within the TCP/IP network.
TCP/IP must be installed on the computer.

Server: Port
Enter the address and port number of the PowCom™ server here in the format IP address:port.
If a name-server is available symbolic names can be used for the address, otherwise the
standard TCP/IP notation is used.
Example: 199.200.110.101:4999
4999 in the example is the port number. PowCom™ only accepts a port number higher than
1000 to avoid conflict with standards used in TCP/IP. The port number must be the same as
the one used by the server.
The standard port number for the PNI is 9000.
Get list
When the address and the port number are entered into Server: Port, select “Get List”. A list
of systems connected to the server displays.
Connect
Highlight one of the systems in the list and select “CONNECT” to set up the connection
to that system. When connection is made the installation information about the system is
shown and the system password has to be entered.
Cancel
Press cancel to leave this window without making a connection.
4.1.5 Com port setup
Figure 4-3 Com port setup
The port set-up menu allows the PowCom™ software to set the PC communication port and
the modem baud rate. Only available COM ports can be set by default.

If automatic detection of available COM ports fails, all ports can be enabled by checking
Enable all ports. Select used com-port and the communication baud-rate. If an incorrect
baud-rate is selected, direct communication will not work. The baud-rate should always be
the same as the controller settings.
• PCC 2400/9600 baud (Default 9600)
• ACX 2400/9600/38400 baud (Default 9600; from 1.11 firmware version 38400)
4.1.6 Properties
4.1.6.1 Message timeout
Message time-out sets the time PowCom™ waits for a reply before sending a new request.
The default value is 1.0, nevertheless, when communicating over long distances, via mobile
phones, radio modems or other equipment that cause a delay in the data flow, it may be
necessary to increase the set time. In most cases 2.0 is sufficient enough.
With time-out increased it takes longer for PowCom™ to discover a broken connection.
The system does not allow values under 1.0.
4.1.6.2 Dial up timeout
This function sets a period of time during which the software waits for a modem to connect
to another modem. The default setting is 60 seconds. This period of time is usually
sufficient, but occasionally it needs to be increased if the remote modem has been set up to
wait for many rings before answering.
4.2 Supervision menu

4.2.1 Set parameters
The Set Parameters menu is located under the Supervision menu and allows system parameters
to be changed. The functions in the window are the same as those in the system controller.
The number of functions displayed in the set parameters vary depending on the particular
system connected. Not all functions listed below are available in all systems.
Some systems have more than one output voltage. In this case a window for the selected
rectifier is opened and limits should be set for the module or module group.
Values for some battery parameters (e.g. battery tests) should be set regarding to the battery
datasheet.
Select rectifier
Some systems have several galvanic isolated output voltages and the possibility for individual
alarm threshold adjustment. Because of this feature the rectifier must be selected before the
alarm adjustment can be made.
However, when one module in a module group is adjusted the others will automatically be
adjusted correspondingly.
4.2.1.1 Adjust Limits
Figure 4-4 Adjust limits window
4.2.1.1.1 Set U1 - U4:

U1 - U4 - voltage reference for the different output modes.
Select output mode for the system. U1 is the normal charge voltage.
U2 is the boost charge voltage.
U3 is battery test voltage. (U3 test value should be less than End voltage battery test value.)
U4 is a spare mode that may be used for a user-defined purpose.
4.2.1.1.2 Auto test:
Sets how many times a year automatic test shall be performed. Exact time and date are
calculated from the installation date. See Set Installation Data section 4.2.5.
4.2.1.1.3 Alarm Limits:
Low voltage alarm
Adjusts the lower limit for voltage before the system gives alarm.
Low voltage alarm value has to be less or equal to formula: High voltage alarm value -1 V.

High voltage alarm

Adjusts the upper limit for voltage before the system gives alarm. If the set value is less
than the “Low voltage alarm” value, the Low voltage alarm value will be automatically
corrected according to formula: High voltage alarm value -1 V.
Over voltage shutdown
If the voltage reaches over this limit, the rectifier that delivers the highest current will be
switched off.
Over voltage shutdown value has to be greater or equal to formula: High voltage alarm
value +1 V. If the condition is not met, the value will be automatically adjusted.
Load/battery disconnection
If the voltage falls below this limit during mains failure, the battery will be disconnected.
If the Load connection is less or equal to Load/battery disconnection, then load connection
is automatically adjusted to Load/battery disconnection +5 V.
Partial load disconnection
Disconnection of lower prioritised load in order to extend backup time for important load.
Disconnection is time controlled or voltage controlled. Partial load disconnection must
be greater than Load/battery disconnection. If it is not, the warning message is displayed.
Partial load disconnection value has to be less than Load connection value.
Partial load disconnection 2
Disconnection is time controlled or voltage controlled.
Partial load disconnection 3
Disconnection is time controlled or voltage controlled.
Load connection
If the battery is disconnected, it will be connected again if the voltage is above this limit
and the mains returned.
It is recommended to set this value 5V above the “Load / battery disconnection” limit.
NOTE Some systems do not include this function.
High load
Entered in percent of the maximum power from the system. If the load current gets higher
than this limit, the system will give alarm to signal that there may not be enough capacity
to charge the battery.

High Temperature limit

Sets the upper limit for temperature before the system gives alarm.
Low Temperature limit
Sets the bottom limit for temperature before the system gives alarm.
Low temperature limit can not be greater than High temperature limit value -10°C. If the
condition is not met, the value will be automatically adjusted.
AC Low Voltage
Sets the bottom limit for the AC voltage before the system gives alarm.
AC High Voltage
Sets the upper limit for the AC voltage before the system gives alarm.
4.2.1.1.4 Battery Test Limits:
Symmetry limit
If the voltage in one block differs from this limit (from the average block voltage) the
system gives alarm.
End voltage battery test
Lower limit for system voltage during test. If the voltage falls below this limit, the test is
stopped and an alarm will be reported. (End voltage battery test value should be greater
than U3 test voltage value.)
Battery test time
Sets the maximum amount of time a test may last. If this limit is reached the test will stop.
Ah. limit for test
Sets the energy that may be discharged from the battery during test. If this limit is reached
the test will stop.
Time for test
Sets the time of day (0-23) when automatic test should start. If the user enters 0, the test
starts at 12AM (midnight) or if the user enters 4, the test starts at 04:00AM.

4.2.1.2 Battery settings
Figure 4-5 Battery Settings Window
4.2.1.2.1 Battery type:

Sets the type of symmetry measurements for connected battery. Indicates how many blocks
each branch is divided into.
4.2.1.2.2 Number of battery branches:
Sets the number of branches on the battery that are equipped with symmetry measuring.
If 0 is selected, controller deactivates symmetry measurement and no “Symmetry fault”
alarm message will be indicated.
4.2.1.2.3 Boost limits:
Boost time (hour)
Sets the duration of boost charging.
Boost interval (weeks)
Sets the number of weeks between each boost.
Boost factor
Boost factor sets the multiplication coefficient for the boost duration. See T1 Limit and T2
Limit.
T1 limit
When the voltage drops below this limit, the system starts counting the time.
When the voltage increases above this limit again, the counting stops. The counted time is
used in a function with the boost factor when the voltage reaches over T2 LIMIT.
T2 limit
When the system increases above this limit the boost will start. The duration is calculated
from the time T1 LIMIT multiplied with the boost factor.
4.2.1.2.4 Battery Current limit:
Allows setting of a maximum battery current. The software always counts on at least 10%
of total battery capacity. This parameter is of the highest priority amongst the parameters
listed in Battery settings Tab, Figure 4-5. (Temperature compensation is of the second
highest priority.)
Battery current limit range is 0-1000A.
4.2.1.2.5 Temperature compensation:
Activates temperature compensation. The charging voltage will be adjusted continuously
according to the compensation factor. The compensation factor depends on the actual type
of the battery.
Temperature compensation factor
When temperature compensation is active the charging voltage is changed according to this
factor. The adjusted charging voltage refers to 20°C.
If the temperature rises 10°C, the voltage will be reduced according to the adjusted
compensation factor. If the temperature drops down the voltage will be adjusted
correspondingly. Adjustment is done continuously. It means that if the temperature is
changed in 1°C, the voltage will be changed by 1/10 of the compensation factor.
4.2.1.2.6 Short interval batt. test (Batt. discontinuance test) (ACX only)
The ACX controller is able to perform an automatic battery discontinuance (or cessation)
test in order to establish if there is a permanent break or interruption in the battery string.
This test can be enabled or disabled. If the test fails, Battery failure alarm is displayed.
Frequency sets how often this test will be performed. The value (in days) can be set from
1 to 7.
Length sets duration of the test. The value (in minutes) can be set between 1 and 10
minutes.
Deviation sets allowed battery current deviation for the test, i.e. if the lowest current
reading is less than this value of the highest reading, alarm will be given. The value (in%)
can be set between 0 and 70.
4.2.1.2.7 System Current Limit:
Provides the ability to select a maximum current from the rectifiers. This option is available
only with ACX firmware supporting this function.

4.2.1.3 Custom Boost Settings (ACX Advanced v2.20 firmware and above)
Designed for Ni-Cd batteries, ACX v2.20 firmware includes a customizable two-stage
boost algorithm to regulate battery recharge current after extended discharges. Like the
automatic boost, the custom boost charges at the U2 voltage setting. However, the recharge
current settings are programmable and are specified as a percentage of the battery capacity;
note the units are designated as Cn [Ah] for the engineered rating (e.g. C5) since it depends
on the application. Also note that custom boost can only be enabled when the Automatic
boost is not selected. PowCom™ automatically alerts and disables one boost mode if the
other is enabled.
The algorithm only kicks in after a discharge of a preset duration, with 30 minutes being
the default. Custom Boost stage 1 defaults to a current limit of 30% Cn [Ah] for a period
1 hour, while stage 2 defaults to a current limit of 10% Cn [Ah] for 17 hours. Stage 2 also
terminates if the current falls below the early-exit setting of 3% Cn [Ah] at which time the
voltage returns to the U1 (Vfloat) settings.
Figure 4-6 Custom Boost Settings Window
To manually start the Custom Boost charging algorithm, use the same dialog box as when
manually setting Automatic boost. First select the Boost radio button and then click
Update.

4.2.2 Set Extra Parameters (ACX only)

The Set Extra Parameters window allows to disconnect the relays manually and change the
parameters for Energy Saving Mode. Parameters can be changed on-line and are not saved
to the configuration file.
4.2.2.1 Low Voltage Disconnection Enable
Some areas have unstable power network. To avoid system damage, it is possible to
disconnect selected LVD or PLD relay manually.
4.2.2.2 Energy Saving Mode
When the button “Rectifier auto on/off” is checked, Energy saving mode starts running.
In this mode the ACX controller is able to turn off the redundant rectifiers automatically
depending on the load. At least 2 rectifiers remain always active and rotate in set time
periods on every address position. Time period for rotation can be set in “Rectifier rotation
time” section of the window. The smallest unit of rotation is 0.1hrs (6mins).
NOTE This window is available only for ACX controller with firmware version 1.14 or
higher.
NOTE If the threshold values for adding/removing another modules are not set in the
configuration file, Energy Saving Mode function will not be activated. It is recommended
to set the Low [%] threshold limit to minimum 25% and High [%] threshold limit to
maximum 90%.
Figure 4-7 Set Extra Parameters

4.2.3 Program version

This window provides information about controller type, hardware version, serial and
configuration numbers.
4.2.4 Set date and time

This function allows to set the date and time in the controller.
The “System time” button enables the user to set the date and time of the controller according
to the PC system time the controller is connected to.
4.2.5 Set installation data
Figure 4-8 Installation data
This menu allows system information to be changed. The information is displayed when
connected to the system. The information has no influence on the function of the system, but
is necessary to identify the system. The installation date should be set when the system is
installed because it is used to calculate the battery test dates.
For ACX controller, if the battery capacity information is needed, battery value has to be set.
4.2.7 Change user password

Select this menu to change the default password. To change the password for the active
telnet list, select “New password”. The system will prompt for the old password, enter it and
then enter the new password twice for verification.

4.2.8 Transfer test data

This menu shows last 10 tests stored in the controller. The tests are numbered in time order
starting with 0 (being the most recent) and 9 (being the oldest). Displayed test data include
information about measured values, end voltage, and maximum deviation of symmetry
voltage.
Test data can be saved to file or viewed in the “View Test Data” window or in a spreadsheet
format. Select “Preview” and an example of the test curve appears.
ACX: If there are any batteries with active symmetry measurement during the test the
symmetry voltages may be downloaded by clicking the Symmetries button. If the button is
gray no data are available. Symmetries may be stored as normal battery test files. The file for
each battery string is saved separately. The filename should not be longer than 7 characters.
Block numbers 1 to 4 are added to the filename automatically according to the battery string.
4.2.9 Get all test data

Get all tests data enables to save all stored tests data to PC. Enter the name of a file. Numbers
0, 1, 2... are added automatically to the file names according to the appertaining tests. The
tests data can be viewed in the “VIEW TEST DATA” window or a spreadsheet.
This function collects all tests data at once while with “TRANSFER TEST DATA” it is
possible to collect only the data from one test at the time. If the filename entered is identical
with the one already existing, the older file is automatically overwritten.
4.2.10 Get battery log (ACX)

“Get battery log” enables to download the battery log data that have been stored in the
controller the first day of the month. Download takes a while, and is indicated by a progress
bar. Click “Save” to save the log as a delimited text file (in which the Tab character usually
separates each field of text). This way it can be imported into Excel or other spreadsheet
programs.
Figure 4-9 Battery Log

4.2.11 System logs (ACX only)

Alarm history
This lists up to the last 1000 events. To see the data use the Download button.
Figure 4-10 Alarm History
Inventory
This contains modules and units history (installation and removing). Up to the 200 last
events can be recorded. To see the Inventory, use the Download button.
Figure 4-11 Inventory

Peak load
This contains the highest load current value for up to last 30 days together with the time it
has occurred. To see the Peak load log, use the Download button.
Figure 4-12 Peak Load
Site data
The controller has a register of 200 entries where an integer for fuse size and a 16 byte
description for load fuses can be stored. It can be modified through this dialog.
Figure 4-13 Site Data

Maintenance and service

The controller has a register of 50 entries with date and a 16 byte description for storing
maintenance entries. If the register is full, the new entry overwrites the oldest one.
Figure 4-14 Maintenance and Service
Statistical data
Contains statistic data about rectifier and load current and battery temperature.
Figure 4-15 Statistical Data

4.2.12 Alarm history

This window shows a list of the last (up to) 40 alarms. Selecting the time on the list displays
a list of alarms active at that time, and also shows changes in the alarm status.
Figure 4-16 Alarm History
4.2.13 Alarm information

The list shows alarms active at the moment.
4.2.14 Alarm dial back

If needed, the controller can be set up to dial back to a certain number in case of an alarm.
Tick off the alarms that should trigger a dial back. Enter the phone number and enable dial
back. Dial back requires a modem connected to the controller. Three modes of dial back are
available.
• Server on change is used together with the PowCom™ phone server and the telephone
number must be the number of that server. Note that this mode dials repeatedly until
contact is made with the server, so do not use this in any other context.
• Pager on change will dial once each time the alarm status change, including when the
alarm is deactivated.

• Pager on new alarm dials once when a new alarm occurs. To send a number to a pager
set the phone number to NNNNNNNN@XXXXX, where NNNNNNNN is the number
of the pager and XXXXX is the number displayed on the pager.
Figure 4-17 Dial Back Control
4.2.15 Set network address

Newer versions of the controller software allow several control units to be connected to
one serial port controlled by a PowCom™ network server, or a UNI (UNIPOWER network
interface). To make this work, each controller must be given a unique address. The address
must be between 2 and 255.
When a UNI is used set the network address to 2.
4.2.16 TCP/IP settings

In systems with PNI (Power Network Interface) built in, the IP-address of the network board
must be set from PowCom™ before the network interface communication is established.
Enter the IP address, net mask and default gateway.

Use a telnet client to log on to the card and do further configuration of the network interface.
See the PNI documentation.
4.2.17 Inventory
The inventory menu displays a list of all modules and units in the system. Click on a module
or a unit and select “View Unit/Module Info”. Further information about the selected item
is displayed.
The Reconfigure button is used when modules or units are permanently removed from the
system to tell the controller that all items that are not communicating have actually been
removed from the system.
Some systems allow a master reset to be performed when connected with a direct connection.
Some systems also allow the controller to be restarted without resetting anything. These
buttons are available only in direct communication if the PowCom™ software supports
them. For security reasons resets are not possible from network or modem connections.
Figure 4-18a Inventory

Figure 4-18b Inventory with 4x64 Multiplexer
4.3 Utilities menu
4.3.1 Log data

The Log Data function can be used to log current, voltage, temperature etc. PowCom™ must
be connected to the system during the log period.
To log the data select File name, define the target directory and then press Start.
The files generated by the logger, cannot be displayed in the “VIEW TEST DATA” window,
but can be imported to a spreadsheet.
Figure 4-19 Log Data
4.3.2 Inventory Log

Inventory log provides information how the system is set. It enables to file and save all the
system data and up-to-day measured values from the controller.

4.3.3 View test data

This window displays test data graphically. Up to four charts can be displayed at the same
time. Select the file you want to see from the file list. Use the Ctrl key and left mouse button
to display several charts at the same time.
The combo boxes marked with X-axis and Y-axis can be used to change the axis values. The
voltage as a function of Ah-discharged can be used to compare data for different tests to see
if the battery voltage falls faster during discharging than when the battery was new.
To delete files use “drag-drop”. Click on a file and drag it to the trash can icon.
Test data files can be saved by using the built in database function. Drag and drop the file in
the database icon (file cabinet) to save.
To open a file in the database, double-click on the database icon, a list of available files will
appear. Select the file from the list.
To cancel the marking of all files in a list: Select only one file, press the Ctrl button and click
the left button on the mouse over the selected file.
The list boxes which covers the graphic area can be moved by clicking the right button of the
mouse and drag the window, or hidden by deselecting Legend.
Figure 4-20 View Test Data

Print...
The Print button allows the file to be sent to a printer. The following options are available:
Full page - Printing the charts in the window in a full-page version. The data for each chart
is printed at the top of the sheet.
Half page - Printing the charts in the window on a half page. The data for each chart is
printed at the top of the sheet.
U, A, Ah - Only available when one chart is selected. Prints voltage, current and ampere-
hours as a function of time in three different curves on one sheet.
Measurements - Prints the values of the test as text.
Printer set-up - Standard printer set-up picture for selecting printer and paper orientation
(landscape or portrait).
Copying to Clipboard - Copies the chart to the clipboard enabling the user to paste it into
a document in another program, e.g. Word. To paste the chart into a Word document, select
PASTE SPECIAL in Word and select PICTURE from the list. The chart will be pasted in the
Word document and can be scaled in Word. To paste the information texts about the different
charts select PASTE SPECIAL once more and select UNFORMATTED TEXT.
4.3.4 View parameter file
Figure 4-21 View Parameter File

Files saved by the save command in the SET PARAMETERS window may be viewed and
edited off-line by selecting this command, Figure 4-21.
This allows a parameter file to be altered and restored to the system at a later time. The
command opens a Set Parameter window for the original system type. The file is saved with
the suffix.prm.
4.3.5 Update configuration

If the configuration of the controller needs to be updated a file from UNIPOWER can be used
to do that.
1. Open the PowCom™ software and choose “Update configuration” from the Utilities
Menu.
2. Another window will open. Choose “Select update file”.
Figure 4-22 Update Configuration
3. Locate the directory that has the update file. Select the file and click “Ok”.
4. Choose “Transfer data to controller” button. The transfer process will take a few seconds.
5. Once the transfer is complete, choose “Store config in flash”.
6. When the system is done, select close from the Configuration updater menu.
7. To check that the configuration is updated, check the configuration number via the PCS
miscellaneous-version menu.
8. If you get a warning that the configuration was not made specifically for this system,
it means that you are trying to load a general configuration. You can do that if you are
sure that the configuration suites the system you try to load it into. If you are not sure
of this then press cancel to abort the operation. It is important not to load unsuitable
configurations since the configuration may change the operation of the system.

4.3.6 Modify configuration

Through this dialog default parameters can be modified and alarms relays assigning can be
changed. This menu item is accessible only if user has appropriate licence.
4.3.7 Configuration wizard

Through this wizard it is possible to create or modify the whole system configuration. It is
accessible only if a user has an appropriate licence.
4.3.8 Button Bar

For starting the direct communication:
For opening network connection window:
For starting the phone list for communication via modem:
For opening the window for selection of baud-rate and serial port:
For opening USB HID communication:
To open the Set parameters window. (Only when communication is established.):
To open the View test data window:

4.4 Tools Menu
4.4.1 Download SD card (ACX only)

The data logging function is used for collecting system data which can be laterused for
analysis or statistical calculations.
Figure 4-23 Download SD Card
The ACX controller logs the data at regular 10-minute-time intervals with the date and time
stamp. The data is saved in separate files for each day in comma separated values file format
(e.g.: 20100513.csv).
NOTE SD card downloading can be applied only to the controllers with SD card fitted.
NOTE The ACX controller supports max. 4GB microSD card, sufficient for more than 20
years of data logging.
This document is believed to be correct at time of publication and UNIPOWER LLC accepts no responsibility for
consequences from printing errors or inaccuracies. Specifications are subject to change without notice.

Instruction Manual Powcom™ 5.2.X: Powering Technology

Uploaded by

Copyright:

Available Formats

Instruction Manual Powcom™ 5.2.X: Powering Technology

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Instruction Manual Powcom™ 5.2.X: Powering Technology

Uploaded by

Copyright:

Available Formats

P O W E R I N G T E C H N O L O G Y

Manual No. POWCOM-7 © 2018 UNIPOWER LLC

Copyright © 1999-2018 UNIPOWER LLC

Manual No. POWCOM-7 2 powcom-man-rev7-0318.indd

Manual No. POWCOM-7 3 powcom-man-rev7-0318.indd

4.2 Supervision menu....................................................................................................................21

Manual No. POWCOM-7 4 powcom-man-rev7-0318.indd

Manual No. POWCOM-7 5 powcom-man-rev7-0318.indd

1.1 General Introduction

1.2 Hardware Requirements

1.3 Feedback & Support

Figure 2-1 Language Selection

Manual No. POWCOM-7 7 powcom-man-rev7-0318.indd

2.2 Compatibility with older versions of PowCom™

2.4 Null-modem Cable

Figure 2-2 Null-modem cable

2.4 USB Cable

Manual No. POWCOM-7 8 powcom-man-rev7-0318.indd

Standard A plug Standard B plug

Figure 2-3 USB cable

Manual No. POWCOM-7 9 powcom-man-rev7-0318.indd

3.1 Main Window

Figure 3-1 Main Window

Manual No. POWCOM-7 10 powcom-man-rev7-0318.indd

Manual No. POWCOM-7 11 powcom-man-rev7-0318.indd

Manual No. POWCOM-7 12 powcom-man-rev7-0318.indd

3.1.1 Module Information

Figure 3-2a Main Window with Displayed Modules

Manual No. POWCOM-7 13 powcom-man-rev7-0318.indd

Manual No. POWCOM-7 14 powcom-man-rev7-0318.indd

Figure 3-3a Main Window with Displayed Modules

Manual No. POWCOM-7 15 powcom-man-rev7-0318.indd

Figure 3-4 Module Info

NOTE Configuration allows manual or automatic module on/off. If the manual or

Manual No. POWCOM-7 16 powcom-man-rev7-0318.indd

4.1 Communication menu

Figure 4-1 Communication menu

4.1.1 Call via modem

Figure 4-2 Example of a phone list

Manual No. POWCOM-7 17 powcom-man-rev7-0318.indd

Manual No. POWCOM-7 18 powcom-man-rev7-0318.indd

Modem Type Initialization String

4.1.2 USB communication (ACX Advanced only)

4.1.3 Direct communication

4.1.4 Network connection

Manual No. POWCOM-7 19 powcom-man-rev7-0318.indd

4.1.5 Com port setup

Figure 4-3 Com port setup

Manual No. POWCOM-7 20 powcom-man-rev7-0318.indd

4.2 Supervision menu

Figure 4-4 Adjust limits window

4.2.1.1.1 Set U1 - U4:

Manual No. POWCOM-7 22 powcom-man-rev7-0318.indd

High voltage alarm

NOTE Some systems do not include this function.

Manual No. POWCOM-7 23 powcom-man-rev7-0318.indd

High Temperature limit

Manual No. POWCOM-7 24 powcom-man-rev7-0318.indd

4.2.1.2 Battery settings