ANNA UNIVERSITY

CHENNAI - 600 025

UNIVERSITY DEPARTMENTS

REGULATIONS 2012

CURRICULA AND SYLLABI FOR

I TO VIII SEMESTERS

B. E. MECHANICAL ENGINEERING
(FULL TIME)

1
2
 ANNA UNIVERSITY, CHENNAI 600 025
UNIVERSITY DEPARTMENT
R - 2012

B.E. MECHANICAL ENGINEERING

I - VIII SEMESTERS CURRICULA AND SYLLABI

SEMESTER I

CODE NO COURSE TITLE L T P C

THEORY
HS8151 Technical English I 3 1 0 4
MA8151 Mathematics I 3 1 0 4
PH8151 Engineering Physics 3 0 0 3
CY8151 Engineering Chemistry 3 0 0 3
GE8151 Computing Techniques 3 0 0 3
GE8152 Engineering Graphics 2 0 3 4
PRACTICAL
PH8161 Physics Laboratory 0 0 2 1
CY8161 Chemistry Laboratory 0 0 2 1
GE8161 Computer Practice Laboratory 0 0 3 2
GE8162 Engineering Practices Laboratory 0 0 3 2
TOTAL 17 2 13 27

SEMESTER II
CODE NO COURSE TITLE L T P C
THEORY
HS8251 Technical English II 3 1 0 4
MA8251 Mathematics II 3 1 0 4
PH8251 Materials Science 3 0 0 3
GE8251 Engineering Mechanics 3 1 0 4
3
 ME8251 Design Concepts in Engineering 3 0 0 3
ME8252 Manufacturing Technology–I 3 0 0 3
PRACTICAL
ME8261 Computer Aided Machine Drawing 0 0 3 2
ME8262 Manufacturing Technology Laboratory-I 0 0 3 2
TOTAL 18 3 6 25

SEMESTER III
CODE NO COURSE TITLE L T P C
THEORY
MA8302 Partial Differential Equations 3 1 0 4
CE8352 Fluid Mechanics and Machinery 3 0 0 3
EC8352 Electronics Engineering 3 0 0 3
EE8251 Basic Electrical Engineering and Measurements 3 0 0 3
ME8301 Engineering Thermodynamics 3 0 0 3
ME8302 Kinematics of Machines 3 0 0 3
PRACTICAL
CE8361 Fluid Mechanics and Machinery Laboratory 0 0 3 2
EC8361 Electronics Engineering Laboratory 0 0 3 2
EE8262 Electrical Engineering Laboratory 0 0 3 2
TOTAL 18 1 9 25

SEMESTER IV
CODE NO COURSE TITLE L T P C
THEORY
GE8351 Environmental Science and Engineering 3 0 0 3
CE8353 Strength of Materials 3 0 0 3
ME8401 Dynamics of Machines 3 0 0 3
ME8402 Thermal Engineering–I 3 0 0 3
ME8451 Manufacturing Technology–II 3 0 0 3

4
 ML8351 Engineering Materials and Metallurgy 3 0 0 3
PRACTICAL
CE8362 Strength of Materials Laboratory 0 0 3 2
ME8411 Thermal Engineering Laboratory–I 0 0 3 2
ME8461 Manufacturing Technology Laboratory–II 0 0 3 2
TOTAL 18 0 9 24

SEMESTER V
CODE NO COURSE TITLE L T P C
THEORY
ME8501 Design of Machine Elements 3 0 0 3
ME8502 Metrology and Measurements 3 0 0 3
ME8503 Thermal Engineering–II 3 0 0 3
ME8551 Computer Aided Design 3 0 0 3
E1 Elective–I 3 0 0 3
E2 Elective–II 3 0 0 3
PRACTICAL
ME8511 Metrology and Measurements Laboratory 0 0 3 2
ME8512 Thermal Engineering Laboratory - II 0 0 3 2
ME8561 Dynamics Laboratory 0 0 3 2
TOTAL 18 0 9 24

SEMESTER VI
CODE NO COURSE TITLE L T P C
THEORY
ME8601 Design of Transmission Systems 3 0 0 3
ME8651 Heat and Mass Transfer 3 1 0 4
ME8652 Industrial Management 3 0 0 3
ME8653 Mechatronics 3 0 0 3
E3 Elective – III 3 0 0 3

5
 E4 Elective -IV 3 0 0 3
PRACTICAL
HS8561 Employability Skills 0 0 2 1
ME8611 C.A.D. / C.A.M. Laboratory 0 0 3 2

ME8612 Creative and Innovative Project 0 0 3 2

TOTAL 18 1 8 24

SEMESTER VII

CODE NO COURSE TITLE L T P C

THEORY
ME8253 Power Plant Engineering 3 0 0 3
ME8701 Computer Integrated Manufacturing 3 0 0 3
ME8752 Finite Element Analysis 3 0 0 3
E5 Elective – V 3 0 0 3
E6 Elective – VI 3 0 0 3
E7 Elective – VII 3 0 0 3
PRACTICAL
ME8661 Mechatronics Laboratory 0 0 3 2
ME8711 Simulation and Analysis Laboratory 0 0 3 2
TOTAL 18 0 6 22

SEMESTER VIII
CODE NO COURSE TITLE L T P C
THEORY
E8 Elective – VIII 3 0 0 3
E9 Elective – IX 3 0 0 3
PRACTICAL
ME8811 Project Work 0 0 12 6
TOTAL 6 0 12 12

TOTAL NO.OF CREDITS : 183

6
 ELECTIVES

CODE NO COURSE TITLE L T P C

THEORY
ME8001 Advanced Internal Combustion Engineering 3 0 0 3
ME8002 Casting and Welding Processes 3 0 0 3
ME8003 Composite Materials and Mechanics 3 0 0 3
ME8004 Design of Heat Exchangers 3 0 0 3
ME8005 Design of Pressure vessel and piping 3 0 0 3
ME8006 Gas Dynamics and Space Propulsion 3 0 0 3
ME8007 Mechanical Vibrations and Noise Control 3 0 0 3
ME8008 Theory of Metal Forming 3 0 0 3
ME8009 Turbo Machinery 3 0 0 3
ME8071 Automobile Engineering 3 0 0 3
ME8072 Computational Fluid Dynamics 3 0 0 3
ME8073 Design for Manufacturing 3 0 0 3
ME8074 Design of Jigs, Fixtures and Press Tools 3 0 0 3
ME8075 Energy Conservation in industries 3 0 0 3
ME8076 Entrepreneurship Development 3 0 0 3
ME8077 Marketing Management 3 0 0 3
ME8078 New and Renewable Sources of Energy 3 0 0 3
ME8079 Non-traditional Machining Processes 3 0 0 3
ME8080 Refrigeration and Air-conditioning 3 0 0 3
ME8081 Reliability Concepts in Engineering 3 0 0 3
ME8552 Hydraulics and Pneumatics 3 0 0 3
MA8356 Probability and Statistics 3 1 0 4
GE8751 Engineering Ethics and Human Values 3 0 0 3
MG8654 Total Quality Management 3 0 0 3
MF8071 Additive Manufacturing Technology 3 0 0 3
MF8074 Industrial Robotics 3 0 0 3

7
MF8075 MEMS and Micro System Fabrication 3 0 0 3
MF8077 Product Design and Development 3 0 0 3
MF8451 Process planning and cost estimation 3 0 0 3
MF8751 Operations Research 3 0 0 3
ML8022 Nondestructive Materials Evaluation 3 0 0 3
GE8072 Disaster Management 3 0 0 3
GE8073 Human Rights 3 0 0 3
HS8151 TECHNICAL ENGLISH I LTPC
(For all branches of B.E / B.Tech programmes) 3104

OBJECTIVES
• To enable all students of engineering and technology develop their basic communication
skills in English.
• To give special emphasis to the development of speaking skills amongst the students of
engineering and technology students.
• To ensure that students use the electronic media such as interne and supplement the
learning materials used in the classroom.
• To inculcate the habit of reading for pleasure.

UNIT I
Listening - Introducing learners to GIE - Types of listening - Listening to audio (verbal &
sounds); Speaking - Speaking about one’s place, important festivals etc. – Introducing
oneself, one’s family / friend; Reading - Skimming a reading passage – Scanning for specific
information - Note-making; Writing - Free writing on any given topic (My favourite place /
Hobbies / School life, etc.) - Sentence completion - Autobiographical writing (writing about
one’s leisure time activities, hometown, etc.); Grammar - Prepositions - Reference words
- Wh-questions - Tenses (Simple); Vocabulary - Word formation - Word expansion (root
words / etymology); E-materials - Interactive exercises for Grammar & Vocabulary - Reading
comprehension exercises - Listening to audio files and answering questions.

UNIT II
Listening - Listening and responding to video lectures / talks; Speaking - Describing a simple
process (filling a form, etc.) - Asking & answering questions - Telephone skills – Telephone
etiquette; Reading – Critical reading - Finding key information in a given text - Sifting facts from
opinions; Writing - Biographical writing (place, people) - Lab descriptions (general/specific
description of laboratory experiments) - Definitions - Recommendations; Grammar - Use of
imperatives - Subject-verb agreement; Vocabulary - Compound words - Word Association;
E-materials - Interactive exercises for Grammar and Vocabulary - Listening exercises with
sample telephone conversations / lectures – Picture-based activities.

UNIT III
Listening - Listening to specific task - focused audio tracks; Speaking - Role-play – Simulation
- Group interaction - Speaking in formal situations (teachers, officials, foreigners); Reading
- Reading and interpreting visual material; Writing - Jumbled sentences - Coherence and
cohesion in writing - Channel conversion (flowchart into process) - Types of paragraph (cause

8
 & effect / compare & contrast / narrative / analytical) - Informal writing (letter/e-mail/blogs) -
Paraphrasing; Grammar - Tenses
(Past) - Use of sequence words - Adjectives; Vocabulary - Different forms and uses of words,
Cause and effect words; E-materials - Interactive exercises for Grammar and Vocabulary -
Excerpts from films related to the theme and follow up exercises - Pictures of flow charts and
tables for interpretations

UNIT IV
Listening - Watching videos / documentaries and responding to questions based on them;
Speaking - Responding to questions - Different forms of interviews - Speaking at different
types of interviews; Reading - Making inference from the reading passage - Predicting the
content of a reading passage; Writing - Interpreting visual materials (line graphs, pie charts
etc.) - Essay writing – Different types of essays; Grammar - Adverbs – Tenses – future
time reference; Vocabulary - Single word substitutes - Use of abbreviations & acronyms;
E-materials - Interactive exercises for Grammar and Vocabulary - Sample interviews - film
scenes - dialogue writing.

UNIT V
Listening - Listening to different accents, Listening to Speeches / Presentations, Listening
to broadcast & telecast from Radio & TV; Speaking - Giving impromptu talks, Making
presentations on given topics; Reading - Email communication - Reading the attachment
files having a poem/joke/proverb - Sending their responses through email Writing - Creative
writing, Poster making; Grammar - Direct and indirect speech; Vocabulary - Lexical items
(fixed / semi fixed expressions); E-materials - Interactive exercises for Grammar & Vocabulary
- Sending emails with attachment – Audio / video excerpts of different accents, - Interpreting
posters
TOTAL : 60 PERIODS
OUTCOMES:
Learners should be able to
 Speak clearly, confidently, comprehensibly, and communicate with one or many listeners
using appropriate communicative strategies.
 Write cohesively and coherently and flawlessly avoiding grammatical errors, using a wide
vocabulary range, organizing their ideas logically on a topic.
 Read different genres of texts adopting various reading strategies.
 Listen/view and comprehend different spoken discourses/excerpts in different accents

TEXT BOOKS:
1. Mindscapes: English for Technologists and Engineers, Orient Black Swan 2012 .
2. S.P.Dhanavel, English and Communication skills for students of science and Engineering,
Orient Black Swan, Chennai, 2011.

REFERENCE BOOKS:
1. Pickett, Nell Ann, Ann A.Laster and Katherine E.Staples. Technical English: Writing,
9
Reading and Speaking. New York: Longman, 2001.
2. Bailey, Stephen. Academic Writing: A practical guide for students. New York:
Rutledge, 2011.
3. Morgan, David and Nicholas Regan. Take-Off:Technical English for Engineering.
Reading: Garnet Publishing Limited, 2008.
4. Thorn, Michael and Alan Badrick. An Introduction to Technical English. Harlow:
Prentice Hall Europe, 1993.
5. Rizvi, M.Ashraf. Effective Technical Communication. New Delhi: Tata McGraw-Hill
Publishing Company, 2007.

EXTENSIVE READERS
1. Murthy, Sudha. Wise & Otherwise. New Delhi: Penguin Books India, 2006.
2. Gates, Bill and Collins Hemingway. Business @ the Speed of Thought: Succeeding
in the Digital Economy. New York: Warner Business Books, 2000.

WEBSITE RESOURCES
1. www.uefap.com
2. www.eslcafe.com
3. www.listen-to-english.com
4. www.owl.english.purdue.edu
5. www.chompchomp.com

MA8151 MATHEMATICS – I LTPC

(Common to all branches of B.E. / B.Tech. Programmes in I Semester) 3 1 0 4
OBJECTIVES:
• To develop the use of matrix algebra techniques this is needed by engineers for practical
applications.
• To make the student knowledgeable in the area of infinite series and their convergence
so that he/ she will be familiar with limitations of using infinite series approximations for
solutions arising in mathematical modeling.
• To familiarize the student with functions of several variables. This is needed in many
branches of engineering.
• To introduce the concepts of improper integrals, Gamma, Beta and Error functions which
are needed in engineering applications.
• To acquaint the student with mathematical tools needed in evaluating multiple integrals
and their usage.

10
 UNIT I MATRICES 9+3
Eigenvalues and Eigenvectors of a real matrix – Characteristic equation – Properties of
eigenvalues and eigenvectors – Cayley-Hamilton Theorem – Diagonalization of matrices –
Reduction of a quadratic form to canonical form by orthogonal transformation – Nature of
quadratic forms.

UNIT II INFINITE SERIES 9+3

Sequences – Convergence of series – General properties – Series of positive terms – Tests
of convergence (Comparison test, Integral test, Comparison of ratios and D’Alembert’s ratio
test) – Alternating series – Series of positive and negative terms – Absolute and conditional
convergence – Power Series – Convergence of exponential, logarithmic and Binomial Series.

UNIT III FUNCTIONS OF SEVERAL VARIABLES 9+3

Limits and Continuity – Partial derivatives – Homogeneous functions and Euler’s theorem
– Total derivative – Differentiation of implicit functions – Change of variables –Jacobians –
Partial differentiation of implicit functions – Taylor’s series for functions of two variables –
Errors and approximations – Maxima and minima of functions of two variables – Lagrange’s
method of undetermined multipliers.

UNIT IV IMPROPER INTEGRALS 9+3

Improper integrals of the first and second kind and their convergence – Evaluation of integrals
involving a parameter by Leibnitz rule – Beta and Gamma functions – Properties – Evaluation
of integrals using Beta and Gamma functions – Error functions.

UNIT V MULTIPLE INTEGRALS 9+3

Double integrals – Change of order of integration – Double integrals in polar coordinates –
Area enclosed by plane curves – Triple integrals – Volume of Solids – Change of variables in
double and triple integrals – Area of a curved surface.
TOTAL : 60 PERIODS
OUTCOMES:
 This course equips students to have basic knowledge and understanding in one field of
materials, integral and differential calculus

TEXT BOOKS:
1. Grewal B.S., “Higher Engineering Mathematics”, Khanna Publishers, New Delhi, 41st
Edition, 2011.
2. Ramana B.V., “Higher Engineering Mathematics”, Tata McGraw Hill Co. Ltd., New Delhi,
11th Reprint, 2010.

REFERENCES:
1. Jain R.K. and Iyengar S.R.K., “Advanced Engineering Mathematics”, Narosa
Publications, New Delhi, 3rd Edition, 2007.
11
2. Bali N., Goyal M. and Watkins C., “Advanced Engineering Mathematics”, Firewall Media
 (An imprint of Lakshmi Publications Pvt., Ltd.,), New Delhi, 7th Edition, 2009.
3. Greenberg M.D., “Advanced Engineering Mathematics”, Pearson Education, New Delhi,
2nd Edition, 5th Reprint, 2009.
4. Peter V.O’Neil, “Advanced Engineering Mathematics”, Cengage Learning India
Pvt., Ltd, New Delhi, 2007.

PH8151 ENGINEERING PHYSICS LTPC

(Common to ALL Branches of B.E./B.Tech.Programmes) 3003
OBJECTIVE:
• To introduce the basic physics concepts relevant to different branches of
Engineering and Technology.

UNIT I PROPERTIES OF MATTER 9

Elasticity - Poisson’s ratio and relationship between moduli (qualitative) - Stress-strain
diagram - factors affecting elasticity - bending of beams - cantilever - bending moment -
theory and experiment of Young’s modulus determination - Uniform and non-uniform
bending - I shaped girders - twisting couple - hollow cylinder - shaft - torsion pendulum -
determination of rigidity modulus- moment of inertia of a body (regular and irregular).

UNIT II ACOUSTICS AND ULTRASONICS 9

Classification of sound - loudness and intensity - Weber-Fechner Law - standard intensity
and intensity level - decibel - reverberation - reverberation time - rate of growth and decay of
sound intensity - derivation of Sabine’s formula - absorption coefficient and its determination -
factors affecting acoustics of buildings : focussing, interference, echo, Echelon effect,
resonance - noise and their remedies. Ultrasonics - production – magnetostriction and
piezoelectric methods - detection of ultrasound - acoustic grating - industrial applications -
NDT - Ultrasonic method: scan modes and practice.

UNIT III THERMAL PHYSICS 9

Thermal expansion - thermal stress - expansion joints - bimetallic strips - thermal
conductivity - conductions in solids - Forbe’s and Lees’ disc methods - Rectilinear flow of
heat through a rod - flow of heat through a compound materials - radical flow of heat
through a spherical shell - thermal insulation of buildings – Laws of blackbody radiation:
Kirchoffs law, Stephens law, Wiens law, Raleigh-Jean law and Planks law (derivation). Laws
of thermodynamics - Otto and diesel engines and their efficiency - entropy - entropy of
Carnot’s cycle - reverse Carnot’s cycle - refrigerator.

UNIT IV APPLIED OPTICS 9

Interference - Michelson interferometer: construction, working, determination of wave length
and thickness - anti-reflection coating - air wedge and its application - Lasers - Einstein’s
coefficients - CO2 , Nd:YAG and semiconductor lasers - homo junction and hetro junction -
12
 construction and working - applications - Optical fibres - classification (index & mode
based) - principle and propagation of light in optical fibres - acceptance angle and numerical
aperture - fibre optic communication system - active and passive sensors.

UNIT V SOLID STATE PHYSICS 9

Nature of bonding - growth of single crystals (qualitative) - crystal systems - crystal planes and
directions - expressions for interplanar distance - coordination number and packing factor for
simple structures: SC, BCC, FCC and HCP - structure and significance of NaCl, ZnS, diamond
and graphite - crystal imperfections: point defects, dislocations and stacking faults - unit cell,
Bravais space lattices - miller indices.
TOTAL: 45 Periods
OUTCOMES:
 The students will have knowledge on the basics of physics related to properties of matter,
optics, acoustics etc., and they will apply these fundamental principles to solve practical
problems related to materials used for engineering applications.

TEXT BOOKS:
1. Gaur R.K., and Gupta, S.L., Engineering Physics, Dhanpat Raj Publications,2003.
2. Palanisamy, P.K., Engineering Physics, Scitech Publications (P) Ltd, 2006.
3. Arumugam, M., Engineering Physics, Anuradha Publications, 2000.

REFERENCES:
1. Sankar, B.N., Pillai.S.O., Engineering Physics, New Age International (P) Ltd., 2007.
2. Rajendran.V Engineering Physics, Tata McGraw-Hill, 2009.

CY8151 ENGINEERING CHEMISTRY LTPC

(Common to all branches of Engineering and Technology) 3003
OBJECTIVES:
 To make the students conversant with basics of polymer chemistry.
 To make the student acquire sound knowledge of second law of thermodynamics and
second law based derivations of importance in engineering applications in all disciplines.
 To acquaint the student with concepts of important photophysical and photochemical
processes and spectroscopy.
 To acquaint the students with the basics of nano materials, their properties and
applications.

UNIT I CHEMICAL THERMODYNAMICS 9

Second law: Entropy - entropy change for an ideal gas, reversible and
irreversible processes; entropy of phase transitions; Clausius inequality. Free
energy and workfunction: Helmholtz and Gibbs free energy functions; Criteria of
spontaneity; Gibbs- Helmholtz equation; Clausius-Clapeyron equation; Maxwell relations
– Van’t Hoff isotherm and isochore. Chemical potential; Gibbs-Duhem equation –
13
variation of chemical potential with temperature and pressure.
 UNIT II POLYMER CHEMISTRY 9
Introduction: Classification of polymers – Natural and Synthetic; Thermoplastic and
Thermosetting. Functionality – Degree of polymerisation. Types and mechanism of
polymerisation: Addition (Free Radical, cationic, anionic and living); condensation and
copolymerisation. Properties of polymers: Tg, Tacticity, Molecular weight – weight average,
number average and polydispersity index. Techniques of polymerisation: Bulk, emulsion,
solution and suspension.

UNIT III KINETICS AND CATALYSIS 9

Introduction – reaction velocity, factors affecting reaction velocity, rate constant, order
of reaction, molecularity, pseudo molecular reactions, zero, first, second and third order
reactions, reactions of fractional orders, determination of order of reactions. Catalysis: Auto
catalysis - Enzyme Catalysis: Michaelis-Menton equation; factors affecting enzyme catalysis.
Heterogeneous Catalysis: Types of adsorption isotherms: Langmuir–Hinselwood and Rideal–
Eley Mechanism.

UNIT IV PHOTOCHEMISTRY AND SPECTROSCOPY 9

Photochemistry: Laws of photochemistry - Grotthuss–Draper law, Stark–Einstein law
and Lambert-Beer Law. Photoprocesses - Internal Conversion, Inter-system crossing,
Fluorescence, Phosphorescence, Chemiluminescence and Photo-sensitisation.
Spectroscopy: Electromagnetic spectrum - Absorption of radiation – Electronic, Vibrational
and rotational transitions. Width and intensities of spectral lines. Spectrophotometric
estimation of iron. UV-visible and IR spectroscopy – principles, instrumentation (Block
diagram) and applications.

UNIT V NANOCHEMISTRY 9
Basics - distinction between molecules, nanoparticles and bulk materials; size-dependent
properties. Nanoparticles: Nanocluster, nanorod, nanotube and nanowire. Synthesis:
Precipitation, thermolysis, hydrothermal, solvothermal, electrodeposition, chemical
vapour deposition, laser ablation; Properties and Applications. Risk discussion and Future
perspectives.
TOTAL : 45 PERIODS
OUTCOMES:
 The knowledge gained on polymer chemistry, thermodynamics. spectroscopy, phase rule
and nano materials will provide a strong platform to understand the concepts on these
subjects for further learning.

TEXT BOOKS:
1. P. Kannan and A. Ravikrishnan, “Engineering Chemistry”, Sri Krishna Hitech Publishing
Company Pvt. Ltd. Chennai, 2009.
2. S. Vairam, P. Kalyani and Suba Ramesh, “Engineering Chemistry”, Wiley India, 2011

14
 REFERENCE BOOKS:
1. P.W. Atkins and de Paula Julio, “Physical Chemistry”, Oxford University Press, 8th Ed.,
(Indian Student Edition) (2009).
2. K. K. Rohatgi-Mukherjee, “Fundamental of Photochemistry” New Age International (P)
Ltd., New Delhi, 1986.
3. G.A. Ozin and A.C. Arsenault, “Nanochemistry: A Chemical Approach to Nanomaterials”,
RSC Publishing, 2005.
4. V.R.Gowariker, N.V.Viswanathan and Jayadev Sreedhar, “Polymer Science”, New Age
International P (Ltd.,), Chennai, 2006

GE8151 COMPUTING TECHNIQUES LTPC

3003
OBJECTIVES:
The students should be made to:
 Learn the organization of a digital computer.
 Be exposed to the number systems.
 Learn to think logically and write pseudo code or draw flow charts for problems.
 Be exposed to the syntax of C.
 Be familiar with programming in C.
 Learn to use arrays, strings, functions, pointers, structures and unions in C.
UNIT I INTRODUCTION 8
Generation and Classification of Computers- Basic Organization of a Computer –Number
System – Binary – Decimal – Conversion – Problems. Need for logical analysis and
thinking – Algorithm – Pseudo code – Flow Chart.

UNIT II C PROGRAMMING BASICS 10

Problem formulation – Problem Solving - Introduction to ‘ C’ programming –fundamentals –
structure of a ‘C’ program – compilation and linking processes – Constants, Variables – Data
Types – Expressions using operators in ‘C’ – Managing Input and Output operations – Decision
Making and Branching – Looping statements – solving simple scientific and statistical problems.

UNIT III ARRAYS AND STRINGS 9

Arrays – Initialization – Declaration – One dimensional and Two dimensional arrays. String-
String operations – String Arrays. Simple programs- sorting- searching – matrix operations.

UNIT IV FUNCTIONS AND POINTERS 9

Function – definition of function – Declaration of function – Pass by value – Pass by reference
– Recursion – Pointers - Definition – Initialization – Pointers arithmetic – Pointers and arrays-
Example Problems.

15
 UNIT V STRUCTURES AND UNIONS 9
Introduction – need for structure data type – structure definition – Structure declaration –
Structure within a structure - Union - Programs using structures and Unions – Storage classes,
Pre-processor directives.
TOTAL: 45 PERIODS
OUTCOMES:
At the end of the course, the student should be able to:
 Design C Programs for problems.
 Write and execute C programs for simple applications.

TEXTBOOKS:
1. Pradip Dey, Manas Ghosh, “Fundamentals of Computing and Programming in C”, First
Edition, Oxford University Press, 2009
2. Ashok N. Kamthane, “Computer programming”, Pearson Education, 2007.
3. Yashavant P. Kanetkar. “ Let Us C”, BPB Publications, 2011.

REFERENCES:
1. Kernighan,B.W and Ritchie,D.M, “The C Programming language”, Second Edition,
Pearson Education, 2006
2. Byron S Gottfried, “ Programming with C”, Schaum’s Outlines, Second Edition, Tata
McGraw-Hill, 2006.
3. R.G. Dromey, “How to Solve it by Computer”, Pearson Education, Fourth Reprint, 2007

GE8152 ENGINEERING GRAPHICS LTPC

2034
OBJECTIVES
• To develop in students, graphic skills for communication of concepts, ideas and design
of engineering products and expose them to existing national standards related to
technical drawings.

CONCEPTS AND CONVENTIONS (NOT FOR EXAMINATION) 1

Importance of graphics in engineering applications – Use of drafting instruments – BIS
conventions and specifications – Size, layout and folding of drawing sheets – Lettering and
dimensioning. Scales: Construction of Diagonal and Vernier scales.

UNIT I PLANE CURVES AND FREE HAND SKETCHING 14

Basic Geometrical constructions, Curves used in engineering practices
Conics – Construction of ellipse, parabola and hyperbola by eccentricity method – Construction
of cycloid – construction of involutes of square and circle – Drawing of tangents and normal
16
 to the above curves.
Visualization concepts and Free Hand sketching: Visualization principles –Representation
of Three Dimensional objects – Layout of views- Free hand sketching of multiple views from
pictorial views of objects

UNIT II PROJECTION OF POINTS, LINES AND PLANE SURFACES 14

Orthographic projection- principles-Principal planes-First angle projection-Projection of points.
Projection of straight lines (only First angle projections) inclined to both the principal planes
- Determination of true lengths and t r u e inclinations by rotating line method and trapezoidal
method and traces
Projection of planes (polygonal and circular surfaces) inclined to both the principal
planes by rotating object method.

UNIT III PROJECTION OF SOLIDS 14

Projection of simple solids like prisms, pyramids, cylinder, cone and truncated solids when
the axis is inclined to one of the principal planes by rotating object method and auxiliary plane
method.

UNIT IV PROJECTION OF SECTIONED SOLIDS AND DEVELOPMENT OF

SURFACES 14
Sectioning of above solids in simple vertical position when the cutting plane is inclined to the
one of the principal planes and perpendicular to the other – obtaining true shape of section.
Development of lateral surfaces of simple and sectioned solids – Prisms, pyramids cylinders
and cones. Development of lateral surfaces of solids with cut-outs and holes

UNIT V ISOMETRIC AND PERSPECTIVE PROJECTIONS 15

Principles of isometric projection – isometric scale –Isometric projections of simple solids
and truncated solids - Prisms, pyramids, cylinders, cones- combination of two solid objects
in simple vertical positions and miscellaneous problems. Perspective projection of simple
solids-Prisms, pyramids and cylinders by visual ray method and vanishing point method.

COMPUTER AIDED DRAFTING (DEMONSTRATION ONLY) 3

Introduction to drafting packages and demonstration of their use.
TOTAL: 75 PERIODS
OUTCOMES:
On Completion of the course the student will be able to
 perform free hand sketching of basic geometrical constructions and multiple views of
objects.
 do orthographic projection of lines and plane surfaces.
 draw projections and solids and development of surfaces.
 prepare isometric and perspective sections of simple solids.
 demonstrate computer aided drafting.

17
TEXT BOOK:
1. N.D.Bhatt and V.M.Panchal, “Engineering Drawing”, Charotar Publishing House, 50th
Edition, 2010.

REFERENCES:
1. K.R.Gopalakrishna., “Engineering Drawing” (Vol I&II combined) Subhas
Stores, Bangalore, 2007
2. Luzzader, Warren.J., and Duff,John M.,,’’ Fundamentals of Engineering Drawing
with an introduction to Interactive Computer Graphics for Design and Production”,
Eastern Economy Edition, Prentice Hall of India Pvt Ltd, New Delhi, 2005
3. M.B.Shah and B.C.Rana, “Engineering Drawing”, Pearson, 2nd Edition, 2009
4. K.Venugopal and V.Prabhu Raja, “Engineering Graphics”, New Age International (P)
Limited ,2008.
5. K. V.Natrajan, “A text book of Engineering Graphics”, Dhanalakshmi Publishers,
Chennai, 2009.
6. Basant Agarwal and Agarwal C.M., “Engineering Drawing”, Tata McGraw Hill Publishing
Company Limited, New Delhi,2008.

Publication of Bureau of Indian Standards:

1. IS 10711 – 2001: Technical products Documentation – Size and lay out of
drawing sheets.
2. IS 9609 (Parts 0 & 1) – 2001: Technical products Documentation – Lettering.
3. IS 10714 (Part 20) – 2001 & SP 46 – 2003: Lines for technical drawings.
4. IS 11669 – 1986 & SP 46 – 2003: Dimensioning of Technical Drawings.
5. IS 15021 (Parts 1 to 4) – 2001: Technical drawings – Projection Methods.

Special points applicable to University Examinations on Engineering Graphics:

1. There will be five questions, each of either or type covering all units of the syllabus.
2. All questions will carry equal marks of 20 each making a total of 100.
3. The answer paper shall consist of drawing sheets of A3 size only. The students will be
permitted to use appropriate scale to fit solution within A3 size.
4. The examination will be conducted in appropriate sessions on the same day

18
 PH 8161 PHYSICS LABORATORY LTPC
(Common to all branches of B.E. / B.Tech. Programmes) 0 021
OBJECTIVES:
 To introduce different experiments to test basic understanding of physics concepts applied
in optics, thermal physics, properties of matter and liquids.

1. Torsional pendulum Determination of rigidity modulus of wire and moment of

inertia of disc
2. Non–uniform bending Determination of young’s modulus
3. Lee’s disc Determination of thermal conductivity of a bad conductor
4. Potentiometer Determination of thermo e.m.f. of thermocouple
5. Air wedge Determination of thickness of a thin sheet of paper
6. i. Optical fibre Determination of Numerical Aperture and acceptance angle
ii. Compact disc Determination of width of the groove using laser
7. Acoustic grating Determination of velocity of ultrasonic waves in liquids
8. Post office box Determination of Band gap of a semiconductor
9. Spectrometer Determination of wavelength using grating
10. Viscosity of liquids Determination of co-efficient of viscosity of a liquid
by Poiseuille’s flow
TOTAL : 30 PERIODS
OUTCOMES:
 The hands on exercises undergone by the students will help them to apply physics
principles of optics and thermal physics to evaluate engineering properties of materials.

CY 8161 CHEMISTRY LABORATORY LT PC

(Common to all branches of Engineering and Technology) 0 021

OBJECTIVES:
 To make the student to acquire practical skills in the determination of water quality
parameters through volumetric and instrumental analysis.
 To acquaint the students with the determination of molecular weight of a polymer by
vacometry.

1. Estimation of HCl using Na2CO3 as primary standard and Determination of alkalinity in

water sample.
2. Determination of total, temporary & permanent hardness of water by EDTA method.
3. Determination of DO content of water sample by Winkler’s method.
4. Determination of chloride content of water sample by argentometric method.
5. Estimation of copper content of the given solution by Iodometry.
6. Determination of strength of given hydrochloric acid using pH meter.
7. Determination of strength of acids in a mixture of acids using conductivity meter.
8. Estimation of iron content of the given solution using potentiometer.
9. Estimation of iron content of the water sample using spectrophotometer (1,10-
phenanthroline / thiocyanate method).
10. Estimation of sodium and potassium present
19
in water using flame photometer.
 11.
Determination of molecular weight of poly vinyl alcohol using Ostwald viscometer.
12.
Pseudo first order kinetics – ester hydrolysis.
13.
Corrosion experiment – weight loss method.
14.
Determination of CMC.
15.
Phase change in a solid.
TOTAL : 30 PERIODS
OUTCOMES:
 The students will be outfitted with hands-on knowledge in the quantitative chemical analysis
of water quality related parameters

REFERENCES:
1. A text of quantitative inorganic analysis, A. L. Vogel , ELBS London. 1995.
2. Experiments in physical chemistry, D.P. Shoemarker and C.W. Gardad, McGraw
Hill, London, 2001,
3. American Public Health Association.

GE8161 COMPUTER PRACTICES LABORATORY LTPC

0032
OBJECTIVES:
The student should be made to:
 Be familiar with the use of Office software.
 Be exposed to presentation and visualization tools.
 Be exposed to problem solving techniques and flow charts.
 Be familiar with programming in C.
 Learn to use Arrays, strings, functions, structures and unions.

LIST OF EXPERIMENTS:
1. Search, generate, manipulate data using MS office/ Open Office
2. Presentation and Visualization – graphs, charts, 2D, 3D
3. Problem formulation, Problem Solving and Flowcharts
4. C Programming using Simple statements and expressions
5. Scientific problem solving using decision making and looping.
6. Simple programming for one dimensional and two dimensional arrays.
7. Solving problems using String functions
8. Programs with user defined functions
9. Program using Recursive Function and conversion from given program to flow chart.
10. Program using structures and unions.
TOTAL : 45 PERIODS

20
OUTCOMES:
At the end of the course, the student should be able to:
 Apply good programming design methods for program development.
 Design and implement C programs for simple applications.
 Develop recursive programs.

GE 8162 ENGINEERING PRACTICES LABORATORY LTPC

(Common to all Branches of B.E. / B.Tech. Programmes) 0032
OBJECTIVE
• To provide exposure to the students with hands-on experience on various
basic engineering practices in Civil, Mechanical, Electrical and Electronics
Engineering.
GROUP – A (CIVIL & ELECTRICAL)

1. CIVIL ENGINEERING PRACTICE 12

PLUMBING
• Basic pipe connections involving the fittings like valves, taps, coupling, unions,
reducers, elbows and other components used in household fittings. Preparation of
plumbing line sketches.
• Laying pipe connection to the suction side of a pump – inlet.
• Laying pipe connection to the delivery side of a pump – out let.
• Practice in mixed pipe connections: Metal, plastic and flexible pipes used in household
appliances.

WOOD WORK
• Sawing, planning and making common joints: T-Joint, Mortise and Tennon joint,
Dovetail joint.

STUDY
• Study of joints in door panels, wooden furniture
• Study of common industrial trusses using models.

2. ELECTRICAL ENGINEERING PRACTICE 9

• Basic household wiring using switches, fuse, indicator – lamp etc.,
• Preparation of wiring diagrams
• Stair case light wiring
• Tube – light wiring
• Study of iron-box, fan with regulator, emergency lamp

GROUP – B (MECHANICAL AND ELECTRONICS) 15

21
 3. MECHANICAL ENGINEERING PRACTICE
WELDING
• Arc welding of butt joints, lap joints, tee joints
• Gas welding Practice.
• Basic Machining
• Simple turning, drilling and tapping operations.
• Machine assembly Practice.
• Study and assembling the following:
• Centrifugal pump, mixies and air conditioners.
• Demonstration on
(a) Smithy operations like the production of hexagonal bolt.
(b) Foundry operation like mould preparation for grooved pulley.

4. ELECTRONIC ENGINEERING PRACTICE 9

• Soldering simple electronic circuits and checking continuity.
• Assembling electronic components on a small PCB and testing.
• Study of Telephone, FM radio, low-voltage power supplies.
TOTAL: 45 PERIODS
OUTCOMES:
 Ability to fabricate carpentry components and pipe connections including plumbing works.
 Ability to use welding equipments to join the structures
 Ability to fabricate electrical and electronics circuits

HS8251 TECHNICAL ENGLISH II LTPC

(For all branches of B.E / B.Tech programmes) 3104
OBJECTIVE
• To make the students acquire listening and speaking skills meant for both formal
and informal contexts
• To help them develop their reading skills by exposing them to different types of
reading strategies
• To equip them with writing skills needed for academic as well as workplace situations
• To make them acquire language skills at their own pace by using e-materials
and language lab component

UNIT I
Listening - Listening to informal conversations and participating; Speaking -
Opening a conversation (greetings, comments on something, weather) - Turn taking -
Closing a conversation (excuses, general wish, positive comment, thanks); Reading -
Developing analytical skills, Deductive and inductive reasoning - Extensive reading; Writing
- Effective use of SMS for sending short notes and messages - Using ‘emoticons’ as
symbols in email messages; Grammar - 22 Regular & irregular verbs - Active and passive
voice; Vocabulary - Homonyms (e.g. ‘can’) - Homophones (e.g. ‘some’, ‘sum’); E-materials
- Interactive exercise on Grammar and vocabulary – blogging; Language Lab - Listening to
different types of conversation and answering questions.

UNIT II
Listening - Listening to situation based dialogues; Speaking - Conversation practice
in real life situations, asking for directions (using polite expressions), giving directions (using
imperative sentences), Purchasing goods from a shop, Discussing various aspects of a film
(they have already seen) or a book (they have already read); Reading - Reading a short
story or an article from newspaper, Critical reading, Comprehension skills; Writing -
Writing a review / summary of a story / article, Personal letter (Inviting your friend to a
function, congratulating someone for his success, thanking one’s friend / relatives);
Grammar - modal verbs, Purpose expressions; Vocabulary - Phrasal verbs and their
meanings, Using phrasal verbs in sentences; E-materials - Interactive exercise on Grammar
and vocabulary, Extensive reading activity (reading stories / novels from links), Posting
reviews in blogs - Language Lab
- Dialogues (Fill up exercises), Recording students’ dialogues.

UNIT III
Listening - Listening to the conversation - Understanding the structure of conversations;
Speaking - Conversation skills with a sense of stress, intonation, pronunciation and meaning
- Seeking information – expressing feelings (affection, anger, regret etc.); Reading - Speed
reading – reading passages with the time limit - Skimming; Writing - Minutes of meeting –
format and practice in the preparation of minutes - Writing summary after reading the articles
from the journals - Format for the journal articles – elements of technical articles (abstract,
introduction, methodology, results, discussion, conclusion, appendices, references) - Writing
strategies; Grammar - Conditional clauses - Cause and effect expressions; Vocabulary -
Words used as nouns and verbs without any change in the spelling (e.g. ‘rock’, ‘train’, ‘ring’);
E-materials - Interactive exercise on Grammar & vocabulary - Speed Reading practice
exercises; Language Lab - Intonation practice using EFLU materials – Attending a meeting
and writing minutes.

UNIT IV
Listening - Listening to a telephone conversation, Viewing a model interview (face-to-face,
telephonic and video conferencing) and observing the practices; Speaking - Role play practice
in telephone skills - listening and responding, -asking questions, -note taking – passing on
messages, Role play and mock interview for grasping the interview skills; Reading - Reading
the job advertisements and the profile of the company concerned – scanning; Writing -
Applying for a job – cover letter - résumé preparation – vision, mission and goals of the
candidate; Grammar - Numerical expressions - Connectives (discourse markers); Vocabulary
- Idioms and their meanings – using idioms in sentences; E-materials - Interactive exercises
on Grammar & Vocabulary - Different forms of résumés- Filling up a résumé / cover letter;
Language Lab - Telephonic interview – recording
23
the responses - e-résumé writing.
 UNIT V
Listening - Viewing a model group discussion and reviewing the performance of each
participant - Identifying the characteristics of a good listener; Speaking - Group discussion
skills – initiating the discussion – exchanging suggestions and proposals – expressing dissent/
agreement – assertiveness in expressing opinions – mind mapping technique; Reading - Note
making skills – making notes from books, or any form of written materials - Intensive reading
Writing - Types of reports – Feasibility / Project report – report format – recommendations /
suggestions – interpretation of data (using charts for effective presentation); Grammar - Use
of clauses; Vocabulary – Collocation; E-materials - Interactive grammar and vocabulary
exercises - Sample GD - Pictures for discussion, Interactive grammar and vocabulary
exercises - Pictures for discussion; Language Lab - Different models of group discussion
TOTAL: 45 PERIODS
OUTCOMES:
Learners should be able to
 Speak convincingly, express their opinions clearly, initiate a discussion, negotiate, argue
using appropriate communicative strategies.
 Write effectively and persuasively and produce different types of writing such as narration,
description, exposition and argument as well as creative, critical, analytical and evaluative
writing.
 Read different genres of texts, infer implied meanings and critically analyse and evaluate
them for ideas as well as for method of presentation.
 Listen/view and comprehend different spoken excerpts critically and infer unspoken and
implied meanings.

TEXT BOOKS:
1. Mindscapes: English for Technologists and Engineers, Orient Black Swan 2012 .
2. S.P.Dhanavel, English and Communication skills for students of science and Engineering,
Orient Black Swan, Chennai, 2011.

REFERENCE BOOKS:
1. Laws, Anne. Presentations. Hyderabad: Orient BlackSwan, 2000.
2. Lewis, Hedwig. Body Language: A Guide for Professionals. New Delhi: Sage
Publications, 1998.
3. Naterop, Jean B. and Rod Revell. Telephoning in English. Cambridge: Cambridge
University Press, 1987.
4. Rutherford, Andrea J. Basic Communication Skills for Technology. New Delhi:
Pearson Education, 2001.
5. Ur, Penny. Teaching Listening Comprehension. Cambridge: Cambridge University
Press, 1984.

EXTENSIVE READERS
1. Abdul Kalam, A P J. Ignited Minds: Unleashing the Power within India. New Delhi:
Penguin Books India, 2002.
24
2. Parameswaran, Uma. C.V.Raman: A Biography. New Delhi: Penguin Books India,
2011.

WEB RESOURCES
1. www.esl-lab.com
2. www.englishgrammar.org
3. www.englishclub.com
4. www.mindtools.com
5. www.esl.about.com

MA8251 MATHEMATICS II LTPC

(Common to all branches of B.E. / B.Tech. Programmes in II Semester) 3 1 0 4

OBJECTIVES:
• To make the student acquire sound knowledge of techniques in solving ordinary
differential equations that model engineering problems.
• To acquaint the student with the concepts of vector calculus, needed for problems in all
engineering disciplines.
• To develop an understanding of the standard techniques of complex variable theory so
as to enable the student to apply them with confidence, in application areas such as
heat conduction, elasticity, fluid dynamics and flow the of electric current.
• To make the student appreciate the purpose of using transforms to create a new domain
in which it is easier to handle the problem that is being investigated.

UNIT I DIFFERENTIAL EQUATIONS 9+3

Method of variation of parameters – Method of undetermined coefficients – Homogenous
equation of Euler’s and Legendre’s type – System of simultaneous linear differential equations
with constant coefficients.

UNIT II VECTOR CALCULUS 9+3

Gradient and directional derivative – Divergence and Curl – Irrotational and Solenoidal vector
fields – Line integral over a plane curve – Surface integral and volume integral - Green’s,
Gauss divergence and Stoke’s theorems – Verification and application in evaluating line,
surface and volume integrals.

UNIT III ANALYTIC FUNCTION 9+3

Analytic functions – Necessary and sufficient conditions for analyticity - Properties – Harmonic
conjugates – Construction of analytic function - Conformal mapping – Mapping by functions
w = z+ c, az, 1/z, z2 - Bilinear transformation.
25
 UNIT IV COMPLEX INTEGRATION 9+3
Line integral - Cauchy’s integral theorem – Cauchy’s integral formula – Taylor’s and Laurent’s
series – Singularities – Residues – Residue theorem – Application of residue theorem for
evaluation of real integrals – Use of circular contour and semicircular contour with no pole on
real axis.
UNIT V LAPLACE TRANSFORMS 9+3
Existence conditions – Transforms of elementary functions – Transform of unit step function
and unit impulse function – Basic properties – Shifting theorems -Transforms of derivatives
and integrals – Initial and final value theorems – Inverse transforms – Convolution theorem –
– Transform of periodic functions – Application to solution of linear ordinary differential
equations with constant coefficients.
TOTAL : 60 PERIODS
OUTCOMES:
 The subject helps the students to develop the fundamentals and basic concepts in vector
calculus, ODE, Laplace transform and complex functions. Students will be able to solve
problems related to engineering applications by using these techniques.

TEXT BOOKS:
1. Grewal B.S., “Higher Engineering Mathematics”, Khanna Publishers, New Delhi,
41st Edition, 2011.
2. Ramana, B.V. “Higher Engineering Mathematics”, Tata McGraw Hill, NewDelhi,
2010.

REFERENCES:
1. Glyn James, “Advanced Modern Engineering Mathematics”, Pearson Education,New
Delhi, 2007.
2. Jain R.K. and Iyengar S.R.K., “Advanced Engineering Mathematics”, Narosa
Publications, New Delhi, 3rd Edition, 2007.
3. Bali N., Goyal M. and Watkins C., “Advanced Engineering Mathematics”,Firewall Media
(An imprint of Lakshmi Publications Pvt., Ltd.,), New Delhi,7th Edition, 2009.
4. Peter V.O’Neil, “Advanced Engineering Mathematics”, Cengage Learning India Pvt.,
Ltd, New Delhi, 2007.

26
PH8251 MATERIALS SCIENCE LTPC
(Common to Manufacturing, Industrial, Mining, Mechanical, 3003
Aeronautical, Automobile and Production Engineering)
OBJECTIVE:
• To introduce the essential principles of materials science for mechanical and related
Engineering applications.

UNIT I MECHANICAL PROPERTIES 9

Introduction to mechanical properties - tensile test - plastic deformation mechanisms - slip
and twinning - role of dislocations in slip - strengthening methods - strain hardening -
refinement of the grain size - solid solution strengthening - precipitation hardening - creep
resistance - creep curves - mechanisms of creep - creep-resistant materials - fracture - the
Griffith criterion - critical stress intensity factor and its determination - fatigue failure - fatigue
tests - methods of increasing fatigue life - hardness - Rockwell and Brinell hardness - Knoop
and Vickers microhardness.

UNIT II PHASE DIAGRAMS 9

Solid solutions - Hume Rothery’s rules - free energy of solid solution - intermediate phases
- The phase rule - single component system - one-component system of iron - binary phase
diagrams - isomorphous systems - the tie-line rule - the level rule - application to isomorphous
system - eutectic phase diagram - peritectic phase diagram - other invariant reactions -
microstructural change during cooling.

UNIT III FERROUS ALLOYS AND HEAT TREATMENT 9

The iron-carbon equilibrium diagram - phases, invariant reactions - microstructue of slowly
cooled steels - eutectoid steel, hypo and hypereutectoid steels - effect of alloying elements
on the Fe-C system - diffusion in solids - Fick’s law - phase transformations - pearlitic
transformations - T-T-T-diagram for eutectoid steel - baintic and martensitic transformations -
tempering of martensite - heat treatment of steels - annealing - normalizing - quenching and
tempering - case hardening - induction, flame and laser hardening - carburizing, cyaniding,
carbonitriding and nitriding.

UNIT IV ELECTRONIC MATERIALS 9

Classification of solids - energy bands - concept of Fermi level - conductor, semiconductor,
insulator - Semiconductors: intrinsic, extrinsic - carrier concentration expression (qualitative)
- compound semiconductors (qualitative) - dielectric materials - polarization mechanisms -
dielectric breakdown - magnetic materials - ferromagnetic materials &hysterisis - ferrites -
superconducting materials, properties, types and applications.

UNIT V NEW MATERIALS AND APPLICATIONS 9

Introduction to Ceramics and its applications - Ceramic Fibres - Fibre reinforced Plastics –
Fibre reinforced Metal – Metallic glasses –27Shape memory alloys – Copper base alloys –
 Nickel – Titanium alloys – Relaxor- Ferroelectric materials – Electro and magneto rheological
fluids - Sensors and Actuators – polymer semiconductos – photoconducting polymers
– liquid crystals - Bio-sensors - Scintillation detectors (Position sensitive) –Bio materials –
hydroxyapatite – PMMA – Silicone.
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to apply the different materials, their
processing, and heat treatments in suitable application in mechanical engineering fields.

TEXT BOOKS:
1. Raghavan, V., Materials Science and Engineering, Prentice Hall of India, 2007.
2. Palanisamy, P.K., Applied Materials Science, Scitech, 2003.
3. Raghavan, V., Physical Metallurgy, Prentice Hall of India, 2002.

REFERENCE BOOKS:
1. Calister, W.D., Materials Science and Engineering an Introduction, John Wiley, 2003.
2. Rajendarn V and Marikani A, Materials Science, Tata McGraw Hill, 2006

GE8251 ENGINEERING MECHANICS LTPC

3104
OBJECTIVE
• To develop capacity to predict the effect of force and motion in the course of carrying out
the design functions of engineering

UNIT I BASICS AND STATICS OF PARTICLES 12

Introduction – Units and Dimensions – Laws of Mechanics – Lami’s theorem, Parallelogram
and triangular Law of forces –– Vectorial representation of forces – Vector operations of
forces -additions, subtraction, dot product, cross product – Coplanar Forces – rectangular
components – Equilibrium of a particle – Forces in space – Equilibrium of a particle in
space – Equivalent systems of forces – Principle of transmissibility .

UNIT II EQUILIBRIUM OF RIGID BODIES 12

Free body diagram – Types of supports –Action and reaction forces –stable equilibrium
– Moments and Couples – Moment of a force about a point and about an axis – Vectorial
representation of moments and couples – Scalar components of a moment – Varignon’s
theorem – Single equivalent force -Equilibrium of Rigid bodies in two dimensions –
Equilibrium of Rigid bodies in three dimensions

UNIT III PROPERTIES OF SURFACES AND SOLIDS 12

Centroids and centre of mass– Centroids of lines and areas - Rectangular, circular,
triangular areas by integration – T section, I section, - Angle section, Hollow section by
using standard formula –Theorems of Pappus28 - Area moments of inertia of plane areas –
 Rectangular, circular, triangular areas by integration – T section, I section, Angle section,
Hollow section by using standard formula – Parallel axis theorem and perpendicular axis
theorem –Principal moments of inertia of plane areas – Principal axes of inertia-Mass
moment of inertia –mass moment of inertia for prismatic, cylindrical and spherical solids
from first principle – Relation to area moments of inertia.

UNIT IV DYNAMICS OF PARTICLES 12

Displacements, Velocity and acceleration, their relationship – Relative motion – Curvilinear
motion -Newton’s laws of motion – Work Energy Equation– Impulse and Momentum –
Impact of elastic bodies.

UNIT V FRICTION AND ELEMENTS OF RIGID BODY DYNAMICS 12

Friction force – Laws of sliding friction – equilibrium analysis of simple systems with sliding
friction –wedge friction-. Rolling resistance -Translation and Rotation of Rigid Bodies – Velocity
and acceleration – General Plane motion of simple rigid bodies such as cylinder, disc/wheel
and sphere.
TOTAL: 60 PERIODS
OUTCOMES:
 ability to explain the differential principles applies to solve engineering problems dealing
with force, displacement, velocity and acceleration.
 ability to analyse the forces in any structures.
 ability to solve rigid body subjected to dynamic forces.

TEXT BOOKS:
1. Beer, F.P and Johnston Jr. E.R. “Vector Mechanics for Engineers (In SI Units): Statics
and Dynamics”, 8th Edition, Tata McGraw-Hill Publishing company, New Delhi (2004).
2. Vela Murali, “Engineering Mechanics”, Oxford University Press (2010)

REFERENCES:
1. Hibbeller, R.C and Ashok Gupta, “Engineering Mechanics: Statics and Dynamics”, 11th
Edition, Pearson Education (2010).
2. Irving H. Shames and Krishna Mohana Rao. G., “Engineering Mechanics – Statics and
Dynamics”, 4th Edition, Pearson Education (2006)
3. J.L.Meriam and L.G.Kraige, “ Engineering Mechanics- Statics - Volume 1, Dynamics-
Volume 2,Third Edition, John Wiley & Sons,(1993)
4. Rajasekaran, S and Sankarasubramanian, G., “Engineering Mechanics Statics and
Dynamics”,3rd Edition, Vikas Publishing House Pvt. Ltd., (2005).
5. Bhavikatti, S.S and Rajashekarappa, K.G., “Engineering Mechanics”, New Age
International (P) Limited Publishers, (1998).
6. Kumar, K.L., “Engineering Mechanics”, 3rd Revised Edition, Tata McGraw-Hill Publishing
company, New Delhi (2008)

29
 ME8251 DESIGN CONCEPTS IN ENGINEERING LTPC
3003
OBJECTIVES:
• To impart the importance of design in today’s context of global competition, environmental
awareness and customer oriented market.
• To impart the basic concepts and various aspects of design using simple examples and
case studies.

UNIT I DESIGN TERMINOLOGY 9

Definition-various methods and forms of design-importance of product design-static and
dynamic products-various design projects-morphology of design-requirements of a good
design-concurrent engineering-computer aided engineering-codes and standards-product
and process cycles-bench marking.

UNIT II DESIGN PROCESS 9

Basic module in design process-scientific method and design method-Need identification,
importance of definition of problem-structured problem, real life problem- gathering
information-customer requirements- Quality Function Deployment (QFD)- product design
specifications-generation of alternative solutions- Analysis and selection-Detail design and
drawings-Prototype, modeling, simulation, testing and evaluation (Basics only)

UNIT III CREATIVITY IN DESIGN 9

Creativity and problem solving-vertical and lateral thinking-invention-psychological view,
mental blocks-Creativity methods-brainstorming, synectics, force fitting methods, mind map,
concept map-Theory of innovative problem solving (TRIZ) - conceptual decomposition-
creating design concepts.

UNIT IV HUMAN AND SOCIETAL ASPECTS 9

Human factors in design, ergonomics, user friendly design-Aesthetics and visual aspects-
environmental aspects-marketing aspects-team aspects-legal aspects-presentation aspects.

UNIT V MATERIAL AND PROCESSES IN DESIGN 9

Material selection for performance characteristics of materials-selection for new design-
substitution for existing design-economics of materials-selection methods-recycling
and material selection-types of manufacturing process, process systems- Design for
manufacturability (DFM) - Design for assembly (DFA).
TOTAL: 45 PERIODS
OUTCOMES:
 Ability to comprehend the steps in the new product design
 Understanding of customer equipments for new product and making specifications.
 Knowledge in the role of creativity in product design
 Ability to decide materials and processes in product development.

30
TEXT BOOK:
1. George E.Dieter , “Engineering Design: A Materials and Processing Approach” 4th
Edition, Tata McGraw Hill, 2008

REFERENCES:
1. Joseph E.Shigley, Charles R.Mische ,”Mechanical Engineering Design”, McGraw Hill
International edition, 6th Edition 2009
2. Edward B.Magrab, “Integrated Product and Process Design and Development” CRC
Press, 1997
3. James Garratt,” Design and Technology”, 2nd Revised Edition, Cambridge University
Press,1996

ME8252 MANUFACTURING TECHNOLOGY – I LTPC

3003
OBJECTIVE:
• To introduce the students to the concepts of basic manufacturing processes and
fabrication techniques, such as metal casting, metal joining, metal forming and
manufacture of plastic components.

UNIT I METAL CASTING PROCESSES 9

Sand Casting – Sand Mould – Type of patterns - Pattern Materials – Pattern allowances –
Moulding sand Properties and testing – Cores –Types and applications – Moulding machines
– Types and applications– Melting furnaces – Principle of special casting processes- Shell,
investment – Ceramic mould – Pressure die casting – Centrifugal Casting - CO2 process – Stir
casting - Defects in Sand casting

31
 UNIT III BULK DEFORMATION PROCESSES 9
Hot working and cold working of metals – Forging processes – Open, impression and closed
die forging – Characteristics of the processes – Typical forging operations – rolling of metals
– Types of Rolling – Flat strip rolling – shape rolling operations – Defects in rolled parts –
Principle of rod and wire drawing – Tube drawing – Principles of Extrusion – Types – Hot and
Cold extrusion

UNIT IV SHEET METAL PROCESSES 9

Sheet metal characteristics – Typical shearing, bending and drawing operations – Stretch
forming operations – Formability of sheet metal – Test methods –special forming processes-
Working principle and applications – Hydro forming – Rubber pad forming – Metal spinning
– Introduction of Explosive forming, magnetic pulse forming, peen forming, Super plastic
forming – Micro forming

UNIT V MANUFACTURE OF PLASTIC COMPONENTS 9

Types and characteristics of plastics – Moulding of thermoplastics – working principles and
typical applications – injection moulding – Plunger and screw machines – Compression
moulding, Transfer Moulding – Typical industrial applications – introduction to blow moulding –
Rotational moulding – Film blowing – Extrusion – Thermoforming – Bonding of Thermoplastics.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to apply the different manufacturing
process and use this in industry for component production

TEXT BOOKS:
1. Kalpakjian. S, “Manufacturing Engineering and Technology”, Pearson Education India
Edition, 2006
2. S. Gowri P. Hariharan, A.Suresh Babu, Manufacturing Technology I, Pearson Education,
2008

REFERENCES:
1. Roy. A. Lindberg, Processes and materials of manufacture, PHI / Pearson education,
2006
2. Hajra Chouldhary S.K and Hajra Choudhury. AK., Elements of workshop Technology,
volume I and II, Media promoters and Publishers Private Limited, Mumbai, 1997
3. Paul Degarma E, Black J.T and Ronald A. Kosher, Eligth Edition, Materials and
Processes, in Manufacturing prentice – Hall of India, 1997.
4. Sharma, P.C., A Text book of production Technology, S.Chand and Co. Ltd., 2004.
5. P.N. Rao, Manufacturing Technology Foundry, Forming and Welding, TMH-2003; 2nd
Edition, 2003

32
 ME8261 COMPUTER AIDED MACHINE DRAWING LTPC
0032
OBJECTIVE
• To make the students understand and interpret drawings of machine components so as
to prepare assembly drawings both manually and using standard CAD packages.
• To familiarize the students with Indian Standards on drawing practices and standard
components.

UNIT I DRAWING STANDARDS 3

Code of practice for Engineering Drawing, BIS specifications – Welding symbols, riveted
joints, keys, fasteners – Reference to hand book for the selection of standard components
like bolts, nuts, screws, keys etc.

UNIT II FITS AND TOLERENCES 3

Limits, Fits – Tolerancing of individual dimensions – Specification of Fits – Preparation of
production drawings and reading of part and assembly drawings, basic principles of geometric
dimensioning & tolerancing.

UNIT III INTRODUCTION TO DRAFTING PACKAGE 6

Drawing, Editing, Dimensioning, Plotting Commands, Layering Concepts, Matching, Detailing,
Detailed drawing, Basic principles of geometric dimensioning & tolerancing.

UNIT IV ASSEMBLY DRAWING

(Preparation of 2D assembled views for the given part details) 33
Preparation of assembled views, both manually and using software package, given part details
for components such as Shaft couplings – Plummer block – Screw jack – Lathe Tailstock –
Universal joint – Machine Vice – Stuffing box – Crosshead – Safety Valves – Non-return
valves – Connecting rod – Piston and crank shaft – Multi plate clutch – Preparation of Bill of
materials and tolerance data sheet.
TOTAL: 20% of classes for theory classes and 80% of
classes for practice = 45 PERIODS
Note: 50% of assembly drawings must be done manually and remaining 50% of assembly
drawings must be done by using any 2D drafting package)

OUTCOMES
 Ability to develop engineering drawing for the industrial component using Indian Standard
code of practice.

TEXT BOOK:
1. Gopalakrishna K.R., “Machine Drawing”, 17th Edition, Subhas Stores Books Corner,
Bangalore, 2003.

33
 REFERENCES:
1. N. D. Bhatt and V.M. Panchal, “Machine Drawing”, 45th Edition, Charator Publishers,
2010
2. Goutam Pohit and Goutam Ghosh, “Machine Drawing with AutoCAD”, 1st Edition,
Pearson Education, 2004
3. Junnarkar, N.D., “Machine Drawing”, 1st Edition, Pearson Education, 2004
4. N. Siddeshwar, P. Kanniah, V.V.S. Sastri, ”Machine Drawing” , published by Tata Mc
GrawHill,2006
5. S. Trymbaka Murthy, “A Text Book of Computer Aided Machine Drawing”, CBS
Publishers, New Delhi, 2007

ME8262 MANUFACTURING TECHNOLOGY LABORATORY – I LTPC

0032
OBJECTIVES:
 To Study and practice the various operations that can be performed in lathe,
shaper, drilling, milling machines etc. and to equip with the practical knowledge
required in the core industries.

LIST OF EXPERIMENTS:
Machining and Machining time estimations for :
1. Taper Turning
2. External Thread cutting
3. Internal Thread Cutting
4. Eccentric Turning
5. Knurling
6. Square Head Shaping
7. Hexagonal Head Shaping
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to demonstrate and fabricate
different types of components using the machine tools

MA8302 PARTIAL DIFFERENTIAL EQUATIONS LTPC

3104
OBJECTIVES
 To introduce Fourier series analysis which is central to many applications in engineering
apart from its use in solving boundary value problems.
 To acquaint the student with Fourier transform techniques used in wide variety of
situations.
34
 To introduce the effective mathematical tools for the solutions of partial differential
equations that model several physical processes and to develop Z transform techniques for
discrete time systems.

UNIT I PARTIAL DIFFERENTIAL EQUATIONS 9+3

Formation – Solutions of first order equations – Standard types and Equations reducible to
standard types – Singular solutions – Lagrange’s Linear equation – Integral surface passing
through a given curve – Classification of Partial Differential Equations - Solution of linear
equations of higher order with constant coefficients – Linear non-homogeneous PDE.

UNIT II FOURIER SERIES 9+3

Dirichlet’s conditions – General Fourier series – Odd and even functions – Half-range Sine
and Cosine series – Complex form of Fourier series – Parseval’s identity – Harmonic Analysis.

UNIT III FOURIER SERIES SOLUTIONS OF PARTIAL

DIFFERENTIALEQUATIONS 9+3
Method of separation of Variables – Solutions of one dimensional wave equation and one-
dimensional heat equation – Steady state solution of two-dimensional heat equation – Fourier
series solutions in Cartesian coordinates.

UNIT IV FINITE DIFFERENCE SOLUTION TO HEAT EQUATION 9+3

Numerical differentiation by finite differences: second order differences for first and second
derivatives – Solution of linear system of equations: Gauss-Elimination method, Thomas
algorithm – Explicit and Crank-Nicholson schemes for one space dimensional heat equation –
Alternating Direction and Implicit method (ADI Method) for two space heat equation.

UNIT V FINITE DIFFERENCE SOLUTION TO POTENTIAL

AND WAVE EQUATIONS 9+3
Iterative solution of linear system of equations: Gauss-Jacobi, Gauss-Seidel and SOR methods --
Finite difference techniques for the solution of two dimensional Laplace’s and Poisson’s equations
on rectangular domain – Leibmann’s method –Lax-Wendroff scheme for first order hyperbolic
equation - Explicit finite difference scheme for one space dimensional wave equation.
TOTAL : 60 PERIODS
OUTCOMES
 The understanding of the mathematical principles on transforms and partial differential
equations would provide them the ability to formulate and solve some of the physical
problems of engineering.

TEXT BOOKS:
1. Grewal B.S., “Higher Engineering Mathematics”, Khanna Publishers, New Delhi, 40th
Edition, 2007.
2. Jain M.K, Iyengar S.R.K and Jain R.K., “Computational Methods for Partial Differential
Equations”, New-Age International, Reprint 2002.
35
REFERENCES:
1. Glyn James, “Advanced Modern Engineering Mathematics”, Pearson Education, 2007.
2. Peter V. O’Neil, ““Advanced Engineering Mathematics”, Cengage Learning, 2007.
3. Grewal, B.S. and Grewal,J.S., “ Numerical methods in Engineering and Science”,
Khanna Publishers, New Delhi, 9th Edition, 2007.
4. G.D.Smith,”Numerical Solutions of Partial Differential Equations”, Oxford University
Press, 3rd Edition,1987.
5. Gerald, C.F. and Wheatley, P.O., “Applied Numerical Analysis”, Pearson Education Asia,
New Delhi, 6th Edition, 2006.

CE8352 FLUID MECHANICS AND MACHINERY LTPC

3003
OBJECTIVE:
• The applications of the conservation laws to flow through pipes and hydraulic machines
are studied .To understand the importance of dimensional analysis. To understand the
importance of various types of flow in pumps and turbines.

UNIT I FLUID PROPERTIES AND FLOW CHARACTERISTICS 8

Units and dimensions- Properties of fluids- mass density, specific weight, specific volume,
specific gravity, viscosity, compressibility, vapor pressure, capillarity and surface tension.
Flow characteristics – concept of control volume - application of control volume to continuity
equation, energy equation and momentum equation.

UNIT II FLOW THROUGH CIRCULAR CONDUITS 7

Hydraulic and energy gradient - Laminar flow through circular conduits and circular annuli-
Boundary layer concepts – types of boundary layer thickness – Darcy Weisbach equation –
friction factor- Moody diagram- commercial pipes- minor losses – Flow through pipes in series
and parallel.

UNIT III DIMENSIONAL ANALYSIS 8

Need for dimensional analysis – methods of dimensional analysis – Similitude –types of
similitude - Dimensionless parameters- application of dimensionless parameters – Model
analysis.

UNIT IV PUMPS 12
Impact of jets - Euler’s equation - Theory of rotodynamic machines – various efficiencies
– velocity components at entry and exit of the rotor- velocity triangles - Centrifugal pumps
– working principle - work done by the impeller - performance curves - Reciprocating pump
- working principle – indicator diagram – work saved by fitting air vessels – Rotary pumps –
classification – comparison of working principle with other pumps – advantages.
36
 UNIT V TURBINES 10
Classification of turbines – heads and efficiencies – velocity triangles – axial, radial and mixed
flow turbines – Pelton wheel and Francis turbine - working principles - work done by water on
the runner – draft tube - specific speed - unit quantities – performance curves for turbines –
governing of turbines.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to apply mathematical knowledge to
predict the properties and characteristics of a fluid.
 Can critically analyse the performance of pumps and turbines.

TEXT BOOKS:
1. Streeter, V. L. and Wylie E. B., Fluid Mechanics, McGraw Hill Publishing Co.(2010)
2. Kumar K. L., Engineering Fluid Mechanics, Eurasia Publishing House(p) Ltd. New
Delhi(2004)
3. Modi P.N. and Seth, S.M. Hydraulics and Fluid Mechanics, Standard Book House
(2002), New Delhi

REFERENCES:
1. Robert W.Fox, Alan T. McDonald, Philip J.Pritchard, “Fluid Mechanics and Machinery”,
ISBN 978-0-470-54755-7, 2011.

EC8352 ELECTRONICS ENGINEERING LTPC

3003
OBJECTIVES:
• To provide knowledge in the basic concepts of Electronics Engineering including
semiconductors, transistors, electronic devices, signal generators and digital
electronics.

UNIT I SEMICONDUCTORS AND RECTIFIERS 9

Classification of solids based on energy band theory, Intrinsic semiconductors, Extrinsic
semiconductors – P-type and N-type, P-N junction, VI Characteristics of PN junction diode,
Half and Full wave rectifiers, Zener effect, Zener diode, Zener diode Characteristics, Zener
diode as a regulator.
UNIT II TRANSISTOR AND AMPLIFIERS 9
Bipolar junction transistors – CB, CE, CC configurations and characteristics, Biasing
circuits – Fixed bias, Voltage divider bias, CE amplifier, Concept of feedback, Negative
feedback, voltage series feedback amplifier, Current series feedback amplifier.
37
 UNIT III FET AND POWER ELECTRONIC DEVICES 9
FET – Configuration and characteristics, FET amplifier, Characteristics and simple applications
of SCR, Diac, Triac and UJT.

UNIT IV SIGNAL GENERATORS AND LINEAR ICS 9

Positive feedback, Sinusoidal oscillators – RC phase shift, Hartley, Colpitts, Wein bridge
oscillators, Operational amplifier – Adder, Inverting and Non-inverting amplifiers, integrator
and differentiator, IC 555 based Astable and Monostable Multivibrators.

UNIT V DIGITAL ELECTRONICS 9

Boolean algebra, Logic Gates, , Half and Full adders, Decoder, Encoder, Multiplexer,
Demultiplexer, Flip flops, Digital to Analog converters - R-2R and weighted resistor types,
Analog to Digital converters - Successive approximation and Flash types.
TOTAL: 45 PERIODS
OUTCOMES:
 Ability to identify electronics components and use of them to design circuits.

TEXT BOOK:
1. Malvino, ‘Electronic Principles’, McGraw Book Co., 1993.
REFERENCES:
1. Grob. B and Schultz. M.E. ‘Basic Electronics’, Tata Mcgraw Hill, 2003.
2. Thomas L. Floyd, ‘Electronics Devices’, Pearson Education, 2002.
3. Thomas L. Floyd, ‘Digital Fundamentals’, Pearson Education, 2003.
4. Millman, Halkias Jacob, Jit Christos and Satyabrata, ‘Electronic devices and Circuits’,
Tata McGraw Hill, 2nd Edition.

EE8251 BASIC ELECTRICAL ENGINEERING AND MEASUREMENTS LTPC

3003
OBJECTIVES
• To impart knowledge on
I. Electric circuit laws
II. Principle of Electrical Machines
III. Various measuring instruments
UNIT I ELECTRICAL CIRCUITS 9
Ohms Law – Kirchhoff’s Law-Steady state solution of DC circuits – introduction to AC circuits –
waveforms and RMS value – Power and power factor- Three phase balanced and unbalanced
circuits-Three phase Power measurement.

UNIT II ELECTRICAL MACHINES 38 9

 Construction and Principle of operation DC machines- Characteristics of DC machines
Construction and Principle of operation of single phase transformers, synchronous machines,
three-phase and single-phase induction motors

UNIT III MEASUREMENT AND INSTRUMENTATION 9

Classification of instruments – moving coil and moving iron meters – Induction type,
dynamometer type wattmeters – Energy meter – Megger – Instrument transformers (CT & PT)
–Wheatstone’s bridge for measurement of unknown resistance ,Maxwell’s bridge for unknown
inductance and Schering Bridge for unknown capacitance

UNIT IV TRANSDUCERS 9
Classification of transducers, strain, RTD, thermocouples, Piezo-electric transducer, LVDT,
Turbine and electromagnetic flow meters, level transducers ultrasonic and fiber optic
transducers, type of sensors, elastic sensors, viscosity, moisture and pH sensors, Digital
transducers, vibrating wire instruments like load cells, stress meter, etc.

UNIT V SIGNAL CONDITIONING AND DISPLAY 9

Instrumentation amplifiers- Filters- A/D and D/A converters - Multiplexing and data acquisition
- LED, LCD and CRT displays.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon Completion of this subject, the students can able to explain different types of
electrical machines and their performance

TEXT BOOKS:
1. Del Toro ‘Electrical Engineering Fundamentals’ Pearson Education, New Delhi, 2007.
2. V.K Mehta and Rohit Mehta ‘ Principle of Electrical Engineering’ S Chand &
Company,2008
3. Alan S. Moris, Principles of Measurements and Instruments, Printice-Hall of India Pvt.
Ltd., New Delhi, 1999.
4. Smarjit Ghosh ‘Fundmentals of Electrical and Electronics Engineering, Second Edition
2007

REFERENCES:
1. Rajendra Prasad ‘Fundamentals of Electrical engineering’ Prentice Hall of India, 2006.
2. Thereja .B.L ‘Fundamentals of Electrical Engineering and Electronics’ S chand & Co Ltd,
2008.
3. Sanjeev Sharma ‘basics of Electrical Engineering’ S.K International Publishers, New
Delhi 2007.
4. John Bird, Electrical Circuits theory and Technology, Elsevier, First India Edition, 2006.
5. Doebeling, E.O., Measurements Systems – Application and Design’, McGrawHill
Publishing Co, 1990.
39
ME8301 ENGINEERING THERMODYNAMICS LTPC
3003
OBJECTIVE:
• To familiarize the students to understand the fundamentals of thermodynamics and to
perform thermal analysis on their behavior and performance.

UNIT I BASIC CONCEPTS AND FIRST LAW 9

Basic concepts - concept of continuum, comparison of microscopic and macroscopic
approach.Path and point functions.Intensive and extensive, total and specific quantities.
System, surrounding, boundary and their types.Thermodynamic Equilibrium.State, path and
process.Quasi-static, reversible and irreversible processes. Heat and work transfer, definition
and comparison, sign convention. Displacement work and other modes of work.P-V diagram.
Zeroth law of thermodynamics – concept of temperature and thermal equilibrium– relationship
between temperature scales –new temperature scales. First law of thermodynamics –
application to closed and open systems – steady and unsteady flow processes.

UNIT II SECOND LAW AND AVAILABILITY ANALYSIS 9

Heat Reservoir, source and sink. Heat Engine, Refrigerator, Heat pump. Statements of second
law and its corollaries. Carnot cycle Reversed Carnot cycle, Performance. Clausius inequality.
Concept of entropy, T-s diagram, Tds Equations, entropy change for - pure substance, ideal
gases - different processes, principle of increase in entropy.Applications of II Law.
High and low grade energy. Available and non-available energy of a source and finite body.
Exergy and irreversibility.Expressions for the exergy of a closed system and open systems.
Exergy balance and entropy generation.Irreversibility. I and II law Efficiency.

UNIT III PROPERTIES OF PURE SUBSTANCE AND STEAM POWER CYCLE 9

Formation of steam and its thermodynamic properties, p-v, p-T, T-v, T-s, h-s diagrams. PVT
surface.Use of Steam Table and Mollier Chart.Determination of dryness fraction.Application
of I and II law for pure substances. Ideal and actual Rankine cycles, Cycle Improvement
Methods - Reheat and Regenerative cycles, Economiser, preheater, Binary and Combined
cycles.

UNIT IV IDEAL AND REAL GASES, THERMODYNAMIC RELATIONS 9

Properties of Ideal gas.Ideal and real gas comparison.Equations of state for ideal and
real gases.Reduced properties.Compressibility factor.Principle of Corresponding states.
Generalised Compressibility Chart and its use. Maxwell relations, Tds Equations, Difference
and ratio of heat capacities, Energy equation, Joule-Thomson Coefficient, ClausiusClapeyron
equation, Phase Change Processes. Simple Calculations.

UNIT V GAS MIXTURES AND PSYCHROMETRY

40 9
 Mole and Mass fraction, Dalton’s and Amagat’s Law.Properties of gas mixture – Molar mass,
gas constant, density, change in internal energy, enthalpy, entropy and Gibbs function.
Psychrometric properties, Psychrometric charts. Property calculations of air vapour mixtures
by using chart and expressions. Psychrometric process – adiabatic saturation, sensible
heating and cooling, humidification, dehumidification, evaporative cooling and adiabatic
mixing. Simple Applications
TOTAL : 45 PERIODS
(Use of Steam tables, Mollier chart and Psychrometric chart permitted)
OUTCOMES:
 Upon completion of this course, the students can able to apply the Thermodynamic
Principles to Mechanical Engineering Application.
 Apply mathematical fundamentals to study the properties of steam, gas and gas mixtures.
TEXT BOOKS :
1. Y. Cengel and MBoles, Thermodynamics - An Engineering Approach, Tata McGrawHill,
7th Edition, 2010.
2. Natarajan E., Engineering Thermodynamics: Fundamentals and Applications, Anuragam
Publications, Chennai,2012.

REFERENCES :
1. Nag.P.K., “Engineering Thermodynamics”, 4th Edition, Tata McGraw-Hill, New Delhi, 2008.
2. Holman.J.P., Thermodynamics, 3rd Edition. McGraw-Hill, 1995.
3. E.Rathakrishnan, Fundamentals of Engineering Thermodynamics, 2nd Edition, Prentice
– Hall of India Pvt. Ltd, 2006
4. Chattopadhyay, P, Engineering Thermodynamics, Oxford University Press, 2010.
5. Arora C.P, “ Thermodynamics”, Tata McGraw-Hill, New Delhi, 2003.
6. Van Wylen and Sonntag, “Classical Thermodynamics”, Wiley Eastern, 1987
7. Venkatesh,A, “Basic Engineering Thermodynamics”,Universities Press (India) Limited, 2007.

ME8302 KINEMATICS OF MACHINES LTPC

3003
OBJECTIVE:
• To understand the basic components and layout of linkages in the assembly of a system/
machine.
• To understand the principles in analyzing the assembly with respect to the displacement,
velocity, and acceleration at any point in a link of a mechanism.
• To understand the motion resulting from a specified set of linkages, design few linkage
mechanisms and cam mechanisms for specified output motions.
41
 • To understand the basic concepts of toothed gearing and kinematics of gear trains and
the effects of friction in motion transmission and in machine components.
UNIT I BASICS OF MECHANISMS 9
Classification of mechanisms – Basic kinematic concepts and definitions – Degree of freedom,
Mobility – Kutzbach criterion, Gruebler’s criterion – Grashof’s Law – Kinematic inversions of
four-bar chain and slider crank chains – Limit positions – Mechanical advantage – Transmission
Angle – Description of some common mechanisms – Quick return mechanisms, Straight line
generators, Dwell mechanisms, Ratchets and Escapements, Universal Joint – Basic structures
of Robot Manipulators (serial & parallel) – Design of quick return crank-rocker mechanisms.

UNIT II KINEMATICS OF LINKAGE MECHANISMS 9

Displacement, velocity and acceleration analysis of simple mechanisms – Graphical method
– Velocity and acceleration polygons – Velocity analysis using instantaneous centres –
Kinematic analysis by complex algebra methods – Vector approach – Computer applications
in the kinematic analysis of simple mechanisms – Coincident points – Coriolis component of
Acceleration – Introduction to linkage synthesis problem.

UNIT III KINEMATICS OF CAM MECHANISMS 9

Classification of cams and followers – Terminology and definitions – Displacement diagrams –
Uniform velocity, parabolic, simple harmonic, cycloidal and polynomial motions – Derivatives
of follower motions – Layout of plate cam profiles – Specified contour cams – Circular arc and
tangent cams – Pressure angle and undercutting – sizing of cams.
UNIT IV GEARS AND GEAR TRAINS 9
Law of toothed gearing – Involutes and cycloidal tooth profiles –Spur Gear terminology and
definitions –Gear tooth action – contact ratio – Interference and undercutting – Non-standard
gear teeth – Helical, Bevel, Worm, Rack and Pinion gears [Basics only] – Gear trains – Speed
ratio, train value – Parallel axis gear trains – Epicyclic Gear Trains – Differentials – Automobile
gear box.

UNIT V FRICTION IN MACHINE ELEMENTS 9

Surface contacts – Sliding and Rolling friction – Friction drives – Friction in screw threads –
Bearings and lubrication – Friction clutches – Belt and rope drives – Friction aspects in brakes
– Friction in vehicle propulsion and braking.
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to apply fundamentals of mechanism
for the design of new mechanisms and analyse them for optimum design.

TEXT BOOK:
1. Uicker, J.J., Pennock G.R and Shigley, J.E., “Theory of Machines and Mechanisms”,3rd
Edition, Oxford University Press, 2009.

REFERENCES: 42
1. Rattan, S.S, “Theory of Machines”, 3rd Edition, Tata McGraw-Hill, 2009.
2. Thomas Bevan, ‘Theory of Machines’, 3rd Edition, CBS Publishers and Distributors,
2005.
3. Cleghorn. W. L, “Mechanisms of Machines”, Oxford University Press, 2005
4. Robert L. Norton, Kinematics and Dynamics of Machinery, Tata McGraw-Hill, 2009.
5. Allen S. Hall Jr., “Kinematics and Linkage Design”, Prentice Hall, 1961
6. Ghosh. A and Mallick, A.K., “Theory of Mechanisms and Machines’, Affiliated East-West
Pvt. Ltd., New Delhi, 1988.
7. Rao.J.S. and Dukkipati.R.V. ‘Mechanisms and Machine Theory’, Wiley-Eastern Ltd.,
New Delhi, 1992.
8. John Hannah and Stephens R.C., ‘Mechanics of Machines’, Viva Low-Prices Student
Edition, 1999.
9. V.Ramamurthi, Mechanics of Machines, Narosa Publishing House, 2002.
10. Khurmi, R.S.,”Theory of Machines”,14th Edition, S Chand Publications.

STANDARDS:
1. IS 2458 : 2001, Vocabulary of Gear Terms – Definitions related to Geometry.
2. IS 3756 : 2002, Method of Gear Correction – Addendum modification for External
cylindrical gears with parallel axes.
3. IS 5267 : 2002 Vocabulary of Gear Terms – Definitions Related to Worm Gear Geometry.
4. IS 12328 : Part 1: 1988 Bevel Gear Systems Part – 1 Straight Bevel Gears.
5. IS 12328 : 1988 Bevel Systems Part – 2 Spiral Bevel Gears.

CE8361 FLUID MECHANICS AND MACHINES LABORATORY LTPC

0032
OBJECTIVE:
• Students should able to verify the principles studied in theory by performing the
experiments in lab.

A. FLOW MEASUREMENT
1. Calibration of Rotometer
2. Flow through Venturimeter
3. Flow through a circular Orifice
4. Determination of mean velocity by Pitot tube
5. Verification of Bernoulli’s Theorem

B. LOSSES IN PIPES
43
 6. Determination of friction coefficient in pipes
7. Determination of losses due to bends, fittings and elbows

C. PUMPS
8. Characteristics of Centrifugal pumps
9. Characteristics of Gear pump
10. Characteristics of Submersible pump
11. Characteristics of Reciprocating pump
D. TURBINES
12. Characteristics of Pelton wheel turbine
13. Characteristics of Francis turbine

E. DETERMINATION OF METACENTRIC HEIGHT

14. Determination of Metacentric height
TOTAL: 45 PERIODS
OUTCOMES:
 Ability to use the measurement equipments for flow measurement
 Ability to do performance trust on different fluid machinery

REFERENCE BOOKS:
1. Hydraulic Laboratory Manual, Centre for Water Resources, Anna University, 2004.
2. Modi P.N. and Seth S.M., Hydraulics and Fluid Mechanics. Standard Book House. New
Delhi, 2000.
3. Subramanya, K.. Flow in open channels, Tata McGraw - Hill pub. Co., 1992.
4. Subramanya, K. Fluid mechanics, Tata McGraw- Hill pub. Co., New Delhi,1992.

EC8361 ELECTRONICS ENGINEERING LABORATORY LTPC

0032
OBJECTIVES:
• Students should able to verify the principles studied in theory by performing experiments
in the laboratory
1. VI Characteristics of PN Junction and Zener Diodes.
2. Characteristics of CE configuration of Transistor.
3. Characteristics of UniJunction Transistor.
4. Characteristics of FET.
5. Operational Amplifier Applications 44
– Adder, Multiplier.
 6. RC Oscillator
7. LC Oscillators
8. IC 555 Astable and Monostable multivibrators
9. Half and Full adders
10. RS , T and D FFs
11. BCD counter using IC 7490
TOTAL : 45 PERIODS

OUTCOMES:
 ability to use of diodes, transistors for rectifiers
 ability to use of operational amplifiers

EE8262 ELECTRICAL ENGINEERING LABORATORY LTPC

0032
OBJECTIVES:
• Students should able to verify the principles studied in theory by performing experiments
in the laboratory
1. Speed Control of DC Shunt Motor
2. Load Test on DC Shunt Motor
3. Study of starters
4. Swinburne’s Test
5. Load Test on DC Series Motor
6. Load Test on three Phase Alternator
7. Load Test on three Phase Induction Motor
8. Wheatstone’s Bridge
9. Load Test on single phase Induction Motor.
10. Load test on Single Phase Transformer.
TOTAL :45 PERIODS
OUTCOMES
 Ability to perform speed characteristic of different electrical machine

45
GE8351 ENVIRONMENTAL SCIENCE AND ENGINEERING LT P C
3 0 0 3
OBJECTIVES:
To the study of nature and the facts about environment.
 To finding and implementing scientific, technological, economic and political solutions to
environmental problems.
 To study the interrelationship between living organism and environment.
 To appreciate the importance of environment by assessing its impact on the human world;
envision the surrounding environment, its functions and its value.
 To study the dynamic processes and understand the features of the earth’s interior and
surface.
 To study the integrated themes and biodiversity, natural resources, pollution control and
waste management.

UNIT I ENVIRONMENT, ECOSYSTEMS AND BIODIVERSITY 14

Definition, scope and importance of environment – need for public awareness - concept of an
ecosystem – structure and function of an ecosystem – producers, consumers and decomposers –
energy flow in the ecosystem – ecological succession – food chains, food webs and ecological
pyramids – Introduction, types, characteristic features, structure and function of the (a) forest
ecosystem (b) grassland ecosystem (c) desert ecosystem (d) aquatic ecosystems (ponds, streams,
lakes, rivers, oceans, estuaries) – Introduction to biodiversity definition: genetic, species and
ecosystem diversity – biogeographical classification of India – value of biodiversity: consumptive
use, productive use, social, ethical, aesthetic and option values – Biodiversity at global, national
and local levels – India as a mega-diversity nation – hot-spots of biodiversity – threats to
biodiversity: habitat loss, poaching of wildlife, man-wildlife conflicts – endangered and endemic
species of India – conservation of biodiversity: In-situ and ex-situ conservation of biodiversity.
Field study of common plants, insects, birds
Field study of simple ecosystems – pond, river, hill slopes, etc.

UNIT II ENVIRONMENTAL POLLUTION 8

Definition – causes, effects and control measures of: (a) Air pollution (b) Water pollution (c) Soil
pollution (d) Marine pollution (e) Noise pollution (f) Thermal pollution (g) Nuclear hazards – soil
waste management: causes, effects and control measures of municipal solid wastes – role of an
individual in prevention of pollution – pollution case studies – disaster management: floods,
earthquake, cyclone and landslides.

Field study of local polluted site – Urban / Rural / Industrial / Agricultural.

UNIT III NATURAL RESOURCES 10

Forest resources: Use and over-exploitation, deforestation, case studies- timber extraction, mining,
dams and their effects on forests and tribal people – Water resources: Use and over-utilization of
surface and ground water, floods, drought, conflicts over water, dams-benefits and problems –
Mineral resources: Use and exploitation, environmental effects of extracting and using mineral
resources, case studies – Food resources: World food problems, changes caused by agriculture
and overgrazing, effects of modern agriculture, fertilizer-pesticide problems, water logging, salinity,
case studies – Energy resources: Growing energy needs, renewable and non renewable energy
sources, use of alternate energy sources. case studies – Land resources: Land as a resource, land
46
degradation, man induced landslides, soil erosion and desertification – role of an individual in
conservation of natural resources – Equitable use of resources for sustainable lifestyles.

Field study of local area to document environmental assets – river / forest / grassland / hill /
mountain.

UNIT IV SOCIAL ISSUES AND THE ENVIRONMENT 7

From unsustainable to sustainable development – urban problems related to energy – water
conservation, rain water harvesting, watershed management – resettlement and
rehabilitation of people; its problems and concerns, case studies – role of non-governmental
organization- environmental ethics: Issues and possible solutions – climate change, global
warming, acid rain, ozone layer depletion, nuclear accidents and holocaust, case studies. –
wasteland reclamation – consumerism and waste products – environment production act – Air
(Prevention and Control of Pollution) act – Water (Prevention and control of Pollution) act – Wildlife
protection act – Forest conservation act – enforcement machinery involved in environmental
legislation- central and state pollution control boards- Public awareness.

UNIT V HUMAN POPULATION AND THE ENVIRONMENT 6

Population growth, variation among nations – population explosion – family welfare programme –
environment and human health – human rights – value education – HIV / AIDS – women and child
welfare – role of information technology in environment and human health – Case studies.
TOTAL : 45 PERIODS
OUTCOMES:
Environmental Pollution or problems cannot be solved by mere laws. Public participation is an
important aspect which serves the environmental Protection. One will obtain knowledge on the
following after completing the course.
 Public awareness of environmental is at infant stage.
 Ignorance and incomplete knowledge has lead to misconceptions
 Development and improvement in std. of living has lead to serious environmental disasters

TEXT BOOKS
1. Gilbert M.Masters, ‘Introduction to Environmental Engineering and Science’, 2nd
edition, Pearson Education (2004).
2. Benny Joseph, ‘Environmental Science and Engineering’, Tata McGraw-Hill, New Delhi, (2006).

REFERENCE BOOKS
1. R.K. Trivedi, ‘Handbook of Environmental Laws, Rules, Guidelines, Compliances and
Standards’, Vol. I and II, Enviro Media.
2 Cunningham, W.P. Cooper, T.H. Gorhani, ‘Environmental Encyclopedia’,Jaico
Publ., House, Mumbai, 2001.
3. Dharmendra S. Sengar, ‘Environmental law’, Prentice hall of India PVT. LTD,New Delhi, 2007.
4. Rajagopalan, R, ‘Environmental Studies-From Crisis to Cure’, Oxford University Press
(2005)

47
 CE8353 STRENGTH OF MATERIALS LTPC
3003
OBJECTIVE:
To understand the stresses developed in bars, compounds bars, beams, shafts, cylinders and
spheres.

UNIT I STRESS, STRAIN AND DEFORMATION OF SOLIDS 9

Rigid bodies and deformable solids – Tension, Compression and Shear Stresses – Deformation
of simple and compound bars – Thermal stresses – Elastic constants – Volumertric strains –
Stresses on inclined planes – principal stresses and principal planes – Mohr’s circle of stress.

UNIT II TRANSVERSE LOADING ON BEAMS AND STRESSES IN BEAM 9

Beams – types transverse loading on beams – Shear force and bending moment in beams –
Cantilevers – Simply supported beams and over – hanging beams. Theory of simple bending
– bending stress distribution – Load carrying capacity – Proportioning of sections – Flitched
beams – Shear stress distribution.

UNIT III TORSION 9

Torsion formulation stresses and deformation in circular and hollows shafts – Stepped shafts
– Deflection in shafts fixed at the both ends – Stresses in helical springs – Deflection of helical
springs, carriage springs.

UNIT IV DEFLECTION OF BEAMS 9

Double Integration method – Macaulay’s method – Area moment Theorems for computation
of slopes and deflections in beams - Conjugate beam and strain energy – Maxwell’s reciprocal
theorems.

UNIT V THIN CYLINDERS, SPHERES AND THICK CYLINDERS 9

Stresses in thin cylindrical shell due to internal pressure circumferential and longitudinal
stresses and deformation in thin cylinders – spherical shells subjected to internal pressure –
Deformation in spherical shells – Lame’s theory – Application of theories of failure.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to apply mathematical knowledge to
calculate the deformation behavior of simple structures.
 Critically analyse problem and solve the problems related to mechanical elements and
analyse the deformation behavior for different types of loads.

TEXT BOOKS:
1. Bansal, R.K., Strength of Materials, Laxmi Publications (P) Ltd., 2007
2. Jindal U.C., Strength of Materials, Asian Books Pvt. Ltd., New Delhi, 2007

REFERENCES:
1. Egor. P.Popov “ Engineering Mechanics48of Solids” Prentice Hall of India, New Delhi,
 2001
2. Subramanian R., Strength of Materials, oxford University Press, Oxford Higher Education
Series, 2007.
3. Hibbeler, R.C., Mechanics of Materials, Pearson Education, Low Price Edition, 2007
4. Ferdinand P. Been, Russell Johnson, J.r. and John J. Dewole Mechanics of Materials,
Tata Mcgraw Hill publishing ‘co. Ltd., New Delhi.

ME8401 DYNAMICS OF MACHINES LTPC

3003
OBJECTIVES:
• To understand the force-motion relationship in components subjected to external forces
and analysis of standard mechanisms.
• To understand the undesirable effects of unbalances resulting from prescribed motions
in mechanism.
• To understand the effect of Dynamics of undesirable vibrations.
• To understand the principles in mechanisms used for governing of machines.

UNIT I FORCE ANALYSIS 9

Applied and constraint forces – Free body diagrams – Static equilibrium conditions – Static
force analysis of simple mechanisms – Dynamic force analysis – Inertia force and Inertia torque
– D Alembert’s principle –Dynamic Analysis in reciprocating engines – Gas forces – Inertia
effect of connecting rod– Bearing loads – Crank shaft torque – Turning moment diagrams –
Fly Wheels – Flywheels of punching presses- Dynamics of Cam-follower mechanism.

UNIT II BALANCING 9
Static and dynamic balancing – Balancing of rotating masses – Balancing a single cylinder
engine – Balancing of Multi-cylinder inline, V-engines – Partial balancing in engines – Balancing
of linkages – Balancing machines-Field balancing of discs and rotors.

UNIT III SINGLE DEGREE FREE VIBRATION 9

Basic features of vibratory systems – Degrees of freedom – single degree of freedom – Free
vibration – Equations of motion – Natural frequency – Types of Damping – Damped vibration
– Torsional vibration of shaft – Critical speeds of shafts – Torsional vibration – Two and three
rotor torsional systems.

UNIT IV FORCED VIBRATION 9

Response of one degree freedom systems to periodic forcing – Harmonic disturbances –
Disturbance caused by unbalance – Support motion –transmissibility – Vibration isolation-
vibration measurement.

49
 UNIT V MECHANISM FOR CONTROL 9
Governors – Types – Centrifugal governors – Gravity controlled and spring controlled
centrifugal governors – Characteristics – Effect of friction – Controlling force. Gyroscopes –
Gyroscopic forces and torques – Gyroscopic stabilization – Gyroscopic effects in Automobiles,
ships and airplanes.
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the Students can able to predict the force analysis in
mechanical system and related vibration issues and can able to solve the problem

TEXT BOOK:
1. Uicker, J.J., Pennock G.R and Shigley, J.E., “Theory of Machines and Mechanisms”,3rd
Edition, Oxford University Press, 2009.

REFERENCES:
1. Rattan, S.S, “Theory of Machines”, 3rd Edition, Tata McGraw-Hill, 2009.
2. Thomas Bevan, ‘Theory of Machines’, 3rd Edition, CBS Publishers and Distributors,
2005.
3. Cleghorn. W. L, “Mechanisms of Machines”, Oxford University Press, 2005
4. Benson H. Tongue, ”Principles of Vibrations”, Oxford University Press, 2nd Edition, 2007
5. Robert L. Norton, Kinematics and Dynamics of Machinery, Tata McGraw-Hill, 2009.
6. Allen S. Hall Jr., “Kinematics and Linkage Design”, Prentice Hall, 1961
7. Ghosh. A and Mallick, A.K., “Theory of Mechanisms and Machines’, Affiliated East-West
Pvt. Ltd., New Delhi, 1988.
8. Rao.J.S. and Dukkipati.R.V. ‘Mechanisms and Machine Theory’, Wiley-Eastern Ltd.,
New Delhi, 1992.
9. John Hannah and Stephens R.C., ‘Mechanics of Machines’, Viva Low-Prices Student
Edition, 1999.
10. Grover. G.T., “Mechanical Vibrations”, Nem Chand and Bros., 1996
11. William T. Thomson, Marie Dillon Dahleh, Chandramouli Padmanabhan, “Theory of
Vibration with Application”, 5th edition Pearson Education, 2011
12. V.Ramamurthi, Mechanics of Machines, Narosa Publishing House, 2002.
13. Khurmi, R.S.,”Theory of Machines”,14th Edition, S Chand Publications.

50
 ME8402 THERMAL ENGINEERING-I LTPC
3003
OBJECTIVE:
• To apply the concepts and laws of thermodynamics for cycle analysis and performance
of heat engines - Internal Combustion(IC) engines and Gas Turbines.
UNIT I GAS POWER CYCLES 9
Air Standard Cycles - Otto, Diesel, Dual, Brayton – cycle Analysis and performance calculations.

UNIT II AIR COMPRESSOR 9

Classification and working principle, work of compression with and without clearance.
Volumetric efficiency, Isothermal efficiency and isentropic efficiency of reciprocating air
compressors. Multistage air compressor and inter cooling – work of multistage air compressor.
Types of compressors and their comparison.

UNIT III INTERNAL COMBUSTION ENGINES AND ITS SYSTEMS 9

IC engine Classification, components and functions. Actual and theoretical - valve and port
timing diagrams, p-v diagrams - for two stroke and four stroke engines. Comparison of two
stroke & four stroke engines and SI & CI engines.

UNIT IV INTERNAL COMBUSTION ENGINE FUELS, COMBUSTION &

PERFORMANCE 9
Comparison of petrol and diesel engine fuel properties and qualities. Air-fuel ratio calculation –
lean and rich mixtures. Combustion in SI & CI Engines – abnormal combustion – phenomenon
and control. Ignition, lubrication and cooling systems. Exhaust gas analysis. Performance
calculations.

UNIT V GAS TURBINES 9

Open and closed Gas turbine cycle analysis - methods of cycle improvement. Regenerative,
intercooled, reheated cycles and their combinations. Performance calculations.
TOTAL: 45 PERIODS
OUTCOMES:
 Ability to understand the various thermal equipment and their cycles of operation
 Knowledge in working of Air Compressors and IC Engines
 Understanding of IC Fuels and their performance
 Knowledge in principle of operations of gas turbines and performance measurements of
gas turbines.

TEXT BOOKS:
1. Rajput, R.K., Thermal Engineering, 8th Edition, Laxmi Publications, 2010
2. Ballaney, P.L., “Thermal Engineering” , Khanna Publishers, 24th Edition, 2003.

REFERENCES:
1. Rathore, M.M, Thermal Engineering, McGraw
51 Hill, 2010.
2. Rudramoorthy, R., Thermal Engineering, 4th Edition, Tata McGraw Hill, New Delhi, 2006.
3. Domkundwar.S, Kothandaraman.C.P, and Domkundwar. A.V, A Course in Thermal
Engineering, Dhanpat Rai & Sons, Fifth edition, 2002.
4. Sarkar B K, Thermal Engineering, McGraw Hill, 2001
5. Zucro,n.j., Principles of jet propulsion and gas turbines, John Wiley, New York, 1970.
6. Ganesan.V, Gas turbines, Tata McGraw-Hill Publication, New Delhi, 1999.
7. Somasundaram, Gas Dynamic and Jet propulsion, New Age International, 1996.

ME8451 MANUFACTURING TECHNOLOGY – II LTPC

3003
OBJECTIVES:
• To understand the concept and basic mechanics of metal cutting, working of standard
machine tools such as lathe, shaping and allied machines, milling, drilling and allied
machines, grinding and allied machines and broaching. To understand the basic concepts
of Computer Numerical Control (CNC) of machine tools and CNC Programming

UNIT I THEORY OF METAL CUTTING 9

Mechanics of chip formation, single point cutting tool, forces in machining, Types of chip,
cutting tools – nomenclature, orthogonal metal cutting, thermal aspects, cutting tool materials,
tool wear, tool life, surface finish, cutting fluids and Machinability.

UNIT II TURNING MACHINES 9

Centre lathe, constructional features, specification, operations – taper turning methods,
thread cutting methods, special attachments, machining time and power estimation. Capstan
and turret lathes- tool layout – automatic lathes: semi automatic – single spindle : Swiss type,
automatic screw type – multi spindle:

UNITIII RECIPROCATING, MILLING AND GEAR CUTTING MACHINES 9

Reciprocating machine tools: shaper, planer, slotter: Types and operations- Hole making :
Drilling ,reaming,boring,Tapping, Milling operations-types of milling cutter –attachments-
machining time calculations -,Gear cutting – forming and generation principle, gear milling ,
hobbing and gear shaping – micro finishing methods

UNIT IV ABRASIVE PROCESS AND BROACHING 9

Abrasive processes: grinding wheel – specifications and selection, types of grinding process
– cylindrical grinding, surface grinding, centreless grinding, internal grinding- micro finishing
methods - Typical applications – concepts of surface integrity, broaching machines: broach
construction – push, pull, surface and continuous broaching machines

52
 UNIT V ADVANCED MANUFACTURING TECHNIQUES 9
Numerical Control(NC) machine tools – CNC types, constructional details, special features,
machining centre, part programming fundamentals CNC – manual part programming – micro
machining – wafer machining
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to understand and compare the
functions and applications of different metal cutting tools and also demonstrate the
programming in CNC machining.

TEXT BOOKS:
1. Roy. A.Lindberg, “Process and materials of manufacture,” PHI/Pearson Education
fourth, Edition 2006.
2. Rao. P.N “Manufacturing Technology,” Metal Cutting and Machine Tools, Tata McGraw-
Hill, New Delhi, 2003.

REFERENCES:
1. Richerd R kibbe, John E. Neely, Roland O.Merges and Warren J.White “Machine Tool
Practices”, Prentice Hall of India, 1998
2. HMT – Production Technology, Tata Mc Graw Hill, 1998.
3. Hajra Choudhury. Elements of Workshop Technology – Vol.II. Media Promoters
4. Geofrey Boothroyd, Fundamentals of Metal Machining and Machine Tools, Mc Graw
Hill, 1984

ML8351 ENGINEERING MATERIALS AND METALLURGY LTPC

3003
OBJECTIVE:
• To impart knowledge on the structure, properties, treatment, testing and applications
of metals and non-metallic materials so as to identify and select suitable materials for
various engineering applications.

UNIT I ALLOYS AND PHASE DIAGRAMS 10

Constitution of alloys – Solid solutions, substitutional and interstitial – phase diagrams,
Isomorphous, eutectic, eutectoid, peritectic, and peritectoid reactions, Iron – Iron carbide
equilibrium diagram. Classification of steel and cast Iron microstructure, properties and
application.

53
 UNIT II HEAT TREATMENT 11
Definition – Full annealing, stress relief, recrystallisation and spheroidising – normalising,
hardening and Tempering of steel. Isothermal transformation diagrams – cooling curves
superimposed on I.T. diagram CCR – Hardenability, Jominy end quench test - Austempering,
martempering – case hardening, carburizing, Nitriding, cyaniding, carbonitriding – Flame and
Induction hardening – Vacuum and Plasma hardening – Current trends, Thermo-mechanical
treatments, elementary ideas on sintering.

UNIT III FERROUS AND NON-FERROUS METALS 9

Effect of alloying additions on steel- α and β stabilisers– stainless and tool steels – HSLA,
Maraging steels – Grey, white, malleable, spheroidal – alloy cast irons, Copper and copper
alloys – Brass, Bronze and Cupronickel – Aluminium and Al-Cu – precipitation strengthening
treatment – Bearing alloys, Mg-alloys, Ni-based super alloys, special non-ferrous metals and
alloys of low coefficient of the thermal expansion, high corrosion resistance, heat resistant
etc.E

UNIT IV NON-METALLIC MATERIALS 9

Polymers – types of polymer, commodity and engineering polymers – Properties and
applications of various thermosetting and thermoplastic polymers (PP, PS, PVC, PMMA, PET,
PC, PA, ABS, PI, PAI, PPO, PPS, PEEK, PTFE, Polymers – Urea and Phenol formaldehydes)
- Engineering Ceramics – Properties and applications of Al2 O3 , SiC, Si3 N4 , PSZ and
SIALON –Composites-Classifications- Matrix and reinforcement Materials- Applications of
Composites- Nano composites.

UNIT V MECHANICAL PROPERTIES AND DEFORMATION MECHANISMS 6

Mechanisms of plastic deformation, slip and twinning – Types of fracture – Testing of materials
under tension, compression and shear loads – Hardness tests (Brinell, Vickers and Rockwell),
Micro and nano-hardness tests, Impact test lzod and charpy, fatigue and creep failure
mechanisms.
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to apply the different materials, their
processing, heat treatments in suitable application in mechanical engineering fields.

TEXT BOOKS:
1. Kenneth G.Budinski and Michael K. Budinski, “Engineering Materials”, Prentice Hall of
India Private Limited, 4th Indian Reprint 2002.
2. Williams D Callister, “Material Science and Engineering” Wiley India Pvt Ltd, Revised
Indian edition 2007

REFERENCES:
1. Raghavan.V, “Materials Science and Engineering”, Prentice Hall of India Pvt.Ltd., 1999.
2. Sydney H.Avner, “Introduction to Physical Metallurgy”, McGraw Hill Book Company,
1994.
54
 3. G.S. Upadhyay and Anish Upadhyay, “Materials Science and Engineering”, Viva Books
Pvt.Ltd., New Delhi, 2006.

CE8362 STRENGTH OF MATERIALS LABORATORY LTPC

0032
OBJECTIVES:
• To study the properties of materials when subjected to different types of loading.

LIST OF EXPERIMENTS
1. Tension test on mild steel rod
2. Double shear test on metal
3. Torsion test on mild steel rod
4. Impact test on metal specimen (Izod and Charpy)
5. Hardness test on metals (Rockwell and Brinell Hardness Tests)
6. Deflection test on metal beam
7. Compression test on helical spring
8. Deflection test on carriage spring
TOTAL: 45 PERIODS
OUTCOMES:
 Ability to perform different destructive testing
 Ability to characteristic materials

REFERENCE:
1. Relevant Indian Standards

55
 ME8411 THERMAL ENGINEERING LABORATORY – I LTPC
0032
OBJECTIVES:
 To study the value timing-V diagram and performance of IC Engines
 To Study the characteristics of fuels/Lubricates used in IC Engines
 To study the Performance of steam generator/ turbine

LIST OF EXPERIMENTS

I.C. ENGINE LAB AND FUELS LAB 30

1. Valve Timing and Port Timing diagrams.
2. Actual p-v diagrams of IC engines.
3. Performance test of Reciprocating Air compressor
4. Performance Test on 4 – stroke Diesel Engine.
5. Heat Balance Test on 4 – stroke Diesel Engine.
6. Morse Test on Multi-cylinder Petrol Engine.
7. Retardation Test on a Diesel Engine.
8. Determination of Flash Point and Fire Point of various fuels / lubricants.

STEAM LAB 15
1. Study of Steam Generators and Turbines.
2. Performance and Energy Balance Test on a Steam Generator.
3. Performance and Energy Balance Test on Steam Turbine.
TOTAL: 45 PERIODS
OUTCOMES:
 Ability to conduct experiment on IC engine to study the characteristic and performance of
IC design/ steam turbines.

ME8461 MANUFACTURING TECHNOLOGY LABORATORY –II LTPC

0032
OBJECTIVES:
• To Study and acquire knowledge on various basic machining operations in special
purpose machines and its applications in real life manufacture of components in the
industry

LIST OF EXPERIMENTS:
1. Contour milling using vertical milling machine
2. Spur gear cutting in milling machine
56
 3. Helical Gear Cutting in milling machine
4. Gear generation in hobbing
5. Gear generation in shaping
6. Spline Broaching
7. Plain Surface grinding
8. Cylindrical grinding
9. Tool angle grinding with tool and Cutter Grinder
10. Measurement of cutting forces in Milling /Turning Process
11. CNC Part Programming.
TOTAL: 45 PERIODS
OUTCOMES:
 Ability to use different machine tools to manufacturing gears.
 Ability to use different machine tools for finishing operations
 Ability to manufacture tools using cutter grinder
 Develop CNC part programming

ME8501 DESIGN OF MACHINE ELEMENTS LTPC

3003
OBJECTIVES
• To familiarize the various steps involved in the Design Process
• To understand the principles involved in evaluating the shape and dimensions of a
component to satisfy functional and strength requirements.
• To learn to use standard practices and standard data
• To learn to use catalogues and standard machine components

UNIT I STEADY STRESSES AND VARIABLE STRESSES IN MACHINE MEMBERS 10

Introduction to the design process - factors influencing machine design, selection of materials
based on mechanical properties - Preferred numbers, fits and tolerances – Direct, Bending
and torsional stress equations – Impact and shock loading – calculation of principle stresses
for various load combinations, eccentric loading – curved beams – crane hook and ‘C’ frame
- Factor of safety - theories of failure – Design based on strength and stiffness –Concepts of
reliability based design - stress concentration – Introduction to creep and design against creep
- Design for finite and infinite life under variable loading.
Cylinders and Pressure vessels for industrial applications – Thin and thick cylinders – Spherical vessels

UNIT II SHAFTS AND COUPLINGS 8

Design of solid and hollow shafts based on strength, rigidity and critical speed – Keys, key
ways and splines – crankshafts - Rigid and flexible
57 couplings.
 UNIT III TEMPORARY AND PERMANENT JOINTS 9
Threaded fastners - Bolted joints including eccentric loading, Knuckle joints, Cotter joints –
Welded joints, riveted joints for structures - theory of bonded joints.

UNIT IV ENERGY STORING ELEMENTS AND ENGINE COMPONENTS 9

Various types of springs, optimization of helical springs - rubber springs - Flywheels considering
stresses in rims and arms for engines and punching machines- Connecting Rods and crank shafts.

UNIT V BEARINGS 9
Sliding contact and rolling contact bearings - Hydrodynamic journal bearings, McKee’s Eqn.,
Sommerfeld Number, Raimondi & Boyd graphs, -- Selection of Rolling Contact bearings -
Seals and Gaskets
TOTAL: 45 PERIODS
Note: (Use of P S G Design Data Book is permitted in the University examination)
OUTCOMES:
 Upon completion of this course, the students can able to successfully design machine
components

TEXT BOOK:
1. Bhandari V, “Design of Machine Elements”, 3rd Edition, Tata McGraw-Hill Book Co, 2010.

REFERENCES:
1. Sundararajamoorthy T. V. Shanmugam .N, “Machine Design”, Anuradha Publications,
Chennai, 2003.
2. Joseph Shigley,Charles Mischke,Richard Budynas and Keith Nisbett “Mechanical
Engineering Design”, 8th Edition, Tata McGraw-Hill , 2008.
3. Robert C. Juvinall and Kurt M. Marshek, “Fundamentals of Machine Design”,4th Edition,
Wiley, 2005
4. Alfred Hall, Halowenko, A and Laughlin, H., “Machine Design”, Tata McGraw-Hill Book
Co.(Schaum’s Outline), 2010
5. Bernard Hamrock,Steven Schmid,Bo Jacobson, “Fundamentals of Machine Elements”,
2nd Edition, Tata McGraw-Hill Book Co., 2006.
6. Orthwein W, “Machine Component Design”, Jaico Publishing Co, 2003.
7. Ansel Ugural, “Mechanical Design – An Integral Approach, 1st Edition, Tata McGraw-Hill
Book Co, 2003.
8. Merhyle F. Spotts, Terry E. Shoup and Lee E. Hornberger, “Design of Machine Elements”
8th Edition, Printice Hall, 2003.

STANDARDS:
1. IS 10260 : Part 1 : 1982 Terms, definitions
58 and classification of Plain bearings Part 1 :
 Construction.
2. IS 10260 : Part 1 : 1982 Terms, definitions and classification of Plain bearings Part 2 :
Friction and Wear.
3. IS 10260 : Part 1 : 1982 Terms, definitions and classification of Plain bearings Part 3 : Lubrication.

ME8502 METROLOGY AND MEASUREMENTS LTPC

3003
OBJECTIVE:
• To provide knowledge on the various Metrological equipments available to measure
the dimension of the components and the correct procedure to be adopted while using
these instruments.
UNIT I INTRODUCTION 5
Introduction to Metrology-Standards-Calibration-Terminologies in Measurement-Errors in
Measurement-Care of Measuring Instuments- Reliability

UNIT II LINEAR AND ANGULAR MEASUREMENTS 10

Linear Measuring Instruments – Evolution – Types – Classification – Limits ,Fits and Tolerences
terminology – gauge design - concepts of interchangeability and selective assembly –
Comparators-Angular measuring instruments – Types – Bevel protractor, clinometers,
angle gauges, spirit levels ,sine bar – Alignment telescope – Autocollimator-Angle Dekkor –
Applications.

UNIT III ADVANCES IN METROLOGY 12

Interferometry – laser interferometers – types – Applications –-Computer Aided Inspection-
Basic concept of CMM – Types of CMM – Constructional features – Probes – Accessories –
Software – Applications – Basic concepts of Machine Vision System – Elements – Applications.

UNIT IV THREAD, GEAR METROLOGY AND FORM MEASUREMENT 10

Thread ,Gear Metrology – Form measurement-Straightness-Flatness, Roundness.Surface
finish measurement.

UNIT V MEASUREMENT OF POWER, FLOW AND TEMPERATURE 8

Force, Torque, Pressure, Power – Mechanical, Pneumatic, Hydraulic and Electrical type. Flow
measurement: Venturimeter, Orifice meter, Rotameter, Pitot tube – Temperature: bimetallic
strip, thermocouples, electrical resistance thermometer .
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the Students can demonstrate different measurement
technologies and use of them in Industrial Components

TEXT BOOKS :
1. 59
Gupta.I.C., “Engineering Metrology”, Dhanpatrai Publications, 2005.
2. Jain R.K., “Engineering Metrology”, Khanna Publishers, 2005

REFERENCES:
1. Shotbolt, “Metrology for Engineers, McGraw Hill, 1990.
2. Beckwith, Marangoni, Lienhard, “Mechanical Measurements”, Pearson Education,
2006.
3. Ernest O.Doebelin, McGraw Hill, Measurement Systems (Application and Design)

ME8503 THERMAL ENGINEERING - II LTPC

3003
OBJECTIVES:
• To integrate the concepts, laws and methodologies from the first course in thermodynamics
into the analysis of cyclic processes.
• To apply the thermodynamic concepts into various thermal applications like Boilers,
Compressors and Refrigeration and Air Conditioning Systems and Waste heat recovery
systems.

UNIT I STEAM NOZZLE 9

Types of nozzles, Flow of steam through nozzles, Shapes of nozzles, Effect of friction, Critical
pressure ratio, Metastable flow.

UNIT II BOILERS 9
Types of boilers, Thermal calculations, Heat balance, Mountings and Accessories, Boiler trial,
Boiler code.

UNIT III STEAM TURBINES 9

Types, Impulse and reaction principles, Compoundings, Velocity diagrams for impulse and
reaction blades, Work done on turbine blades and efficiency of components, Speed regulations,
Governors.

UNIT IV COGENERATION AND WASTE HEAT RECOVERY 9

Cogeneration Principles, Cycle Analysis, Applications, Source and utilization of waste heat,
Systems, Heat exchangers, Economics - Analysis.

UNIT V REFRIGERATION AND AIR – CONDITIONING 9

Vapour compression Refrigeration cycle, Superheat, Sub cooling, Performance
calculations, Working principle of vapour absorption system, Air cycle refrigeration, Thermo
electric refrigeration, Psychrometry and Psychrometric properties, Psychrometric chart,
Instrumentation, Cooling load calculations and circulating systems, concept of RSHF, GSHF
and ESHF, Air conditioning systems.
60
TOTAL: 45 PERIODS
OUTCOMES:
 Knowing the types and flow characteristics of nozzles
 understanding the types and working of boilers and steam turbines, cogeneration and heat
recovery
 Knowledge of refrigeration and air conditioning system

TEXT BOOKS:
1. Rajput, “Thermal Engineering”, 8th Edition, Laxmi Publications, 2010.
2. Rudramoorthy R, “Thermal Engineering”, Tata MC Graw Hill, New Delhi, 2003.

REFERENCES:
1. Kothandaraman, C.P., Domkundwar .S and Domkundwar A.V.,” A course in Thermal
Engineering”, Dhanpat Rai & Sons, Fifth Edition, 2002.
2. Holman .J.P., “Thermodynamics”, McGraw Hill, 1985.
3. Arora .C.P., “Refrigeration and Air Conditioning”, TMH, 1994.
4. Charles H Butler : Cogeneration” McGraw Hill, 1984.
5. Sydney Reiter “Industrial and Commercial Heat Recovery Systems” Van Nostrand
Reinhols, 1985.
6. David Gunn, Robert Horton, Industrial Boilers – Longman Scientific and Technical
Publication, 1986.

ME8551 COMPUTER AIDED DESIGN LTPC

3003
OBJECTIVES:
• To provide an overview of how computers are being used in design

UNIT I FUNDAMENTALS OF COMPUTER GRAPHICS 9

Product cycle- Design process- sequential and concurrent engineering- Computer aided
design – CAD system architecture- Computer graphics – co-ordinate systems- 2D and 3D
transformations- homogeneous coordinates - Line drawing -Clipping- viewing transformation

UNIT II GEOMETRIC MODELING 9

Representation of curves- Hermite curve- Bezier curve- B-spline curves-rational curves-
Techniques for surface modeling – surface patch- Coons and bicubic patches- Bezier and
B-spline surfaces. Solid modeling techniques- CSG and B-rep

UNIT III VISUAL REALISM 9

Hidden – Line-Surface-Solid removal algorithms – shading – colouring – computer animation.

61
 UNIT IV ASSEMBLY OF PARTS 9
Assembly modelling – interferences of positions and orientation – tolerance analysis-mass
property calculations – mechanism simulation and interference checking.

UNIT V CAD STANDARDS 9

Standards for computer graphics- Graphical Kernel System (GKS) - standards for exchange
images- Open Graphics Library (OpenGL) - Data exchange standards - IGES, STEP, CALS
etc. - communication standards.

TOTAL : 45 PERIODS
OUTCOMES:
• Upon completion of this course, the students can able to use computer and CAD software's
for modeling of mechanical components

TEXT BOOKS:
1. Ibrahim Zeid “Mastering CAD CAM” Tata McGraw-Hill Publishing Co.2007

REFERENCES:
1. Chris McMahon and Jimmie Browne “CAD/CAM Principles, practice and manufacturing
management “ (Second edition) -Pearson Education
2. William M Neumann and Robert F.Sproul “Principles of Computer Graphics”, Mc Graw
Hill Book Co. Singapore, 1989.
3. Donald Hearn and M. Pauline Baker “Computer Graphics”’. Prentice Hall, Inc, 1992.
4. Foley, Wan Dam, Feiner and Hughes - Computer graphics principles & practice Pearson
Education - 2003.

62
 ME8511 METROLOGY AND MEASUREMENTS LABORATORY LTPC
0032
OBJECTIVES

 To familiar with different measurement equipments and use of this industry for
quality inspection

LIST OF EXPERIMENTS
1. Tool Maker’s Microscope
2. Comparator
3. Sine Bar
4. Gear Tooth Vernier Caliper
5. Floating gauge Micrometer
6. Co ordinate Measuring Machine (Study)
7. Surface Finish Measuring Equipment
8. Vernier Height Gauge
9. Machine Vision System (Study)
10. Bore diameter measurement using telescope gauge
11. Bore diameter measurement using micrometer
12. Force Measurement
13. Torque Measurement
14. Temperature measurement
TOTAL: 45 PERIODS
OUTCOMES
 Ability to handle different measurement tools and perform measurements in quality
impulsion

ME8512 THERMAL ENGINEERING LABORATORY – II LTPC

0032
OBJECTIVES
 To study the heat transfer phenomena predict the relevant coefficient using
implementation
 To study the performance of refrigeration cycle / components

LIST OF EXPERIMENTS:

HEAT TRANSFER: 30
1. Thermal conductivity measurement using guarded plate apparatus.
2. 63 insulation using lagged pipe apparatus.
Thermal conductivity measurement of pipe
 3. Determination of heat transfer coefficient under natural convection from a vertical
cylinder.
4. Determination of heat transfer coefficient under forced convection from a tube.
5. Determination of Thermal conductivity of composite wall.
6. Determination of Thermal conductivity of insulating powder.
7. Heat transfer from pin-fin apparatus (natural & forced convection modes)
8. Determination of Stefan – Boltzmann constant.
9. Determination of emissivity of a grey surface.
10. Effectiveness of Parallel / counter flow heat exchanger.

REFRIGERATION AND AIR CONDITIONING LAB 15

1. Determination of COP of a refrigeration system
2. Experiments on Psychrometric processes
3. Performance test on a reciprocating air compressor
4. Performance test in a HC Refrigeration System
5. Performance test in a fluidized Bed Cooling Tower
TOTAL : 45 PERIODS
OUTCOMES
 Ability to demonstrate the fundamentals of heat and predict the coefficient used in
that transfer application and also design refrigeration cycle.

ME8561 DYNAMICS LABORATORY LTPC

0032
OBJECTIVES:
• To supplement the principles learnt in kinematics and Dynamics of Machinery.
• To understand how certain measuring devices are used for dynamic testing.

LIST OF EXPERIMENTS
1. a) Study of gear parameters.
b) Experimental study of velocity ratios of simple, compound, Epicyclic and
differential gear trains.
2. a) Kinematics of Four Bar, Slider Crank, Crank Rocker, Double crank, Double
rocker, Oscillating cylinder Mechanisms.
64
 b) Kinematics of single and double universal joints.
3. a) Determination of Mass moment of inertia of Fly wheel and Axle system.
b) Determination of Mass Moment of Inertia of axisymmetric bodies using Turn
Table apparatus.
c) Determination of Mass Moment of Inertia using bifilar suspension and compound
pendulum.
4. Motorized gyroscope – Study of gyroscopic effect and couple.
5. Governor - Determination of range sensitivity, effort etc., for Watts, Porter, Proell, and
Hartnell Governors.
6. Cams – Cam profile drawing, Motion curves and study of jump phenomenon
7. a) Single degree of freedom Spring Mass System – Determination of natural
Frequency and verification of Laws of springs – Damping coefficient determination.
b) Multi degree freedom suspension system – Determination of influence coefficient.
8. a) Determination of torsional natural frequency of single and Double Rotor systems.-
Undamped and Damped Natural frequencies.
b) Vibration Absorber – Tuned vibration absorber.
9. Vibration of Equivalent Spring mass system – undamped and damped vibration.
10. Whirling of shafts – Determination of critical speeds of shafts with concentrated loads.
11. a) Balancing of rotating masses. (b) Balancing of reciprocating masses.
12. a) Transverse vibration of Free-Free beam – with and without concentrated masses.
b) Forced Vibration of Cantilever beam – Mode shapes and natural frequencies.
c) Determination of transmissibility ratio using vibrating table.
TOTAL : 45 PERIODS

Note : Atleast 10 experiments must be conducted depending on availability of experiments.

OUTCOME
 Ability to demonstrate the principles of kinematics and dynamics of machinery
 Ability to use the measuring devices for dynamic testing.

ME8601 DESIGN OF TRANSMISSION SYSTEMS LTPC

3003
OBJECTIVES:
• To gain knowledge on the principles and procedure for the design of Mechanical power
Transmission components.
• 65 available for Design of Transmission of
To understand the standard procedure
 Mechanical elements
• To learn to use standard data and catalogues

UNIT I SELECTION OF PRIME MOVERS AND DESIGN FOR FLEXIBLE

ELEMENTS 9
Electric motor classification, Alternating current motors, Polyphase motors, Universal motors,
Motor selection: Speed-Torque curves for AC& DC motors, Speed control of electrical motors,
Driven machine speed-Torque curves, Motor selection: Matching the motor to the driven
machine, Time to accelerate operating speed, Gasoline and diesel engines. Design of Flat
belts and pulleys - Selection of V belts and pulleys – Selection of hoisting wire ropes and
pulleys – Design of Transmission chains and Sprockets. Selection of pulleys and sprockets
for the above transmission systems.

UNIT II SPUR GEARS AND PARALLEL AXIS HELICAL GEARS 9

Speed ratios and number of teeth-Force analysis -Tooth stresses - Dynamic effects - Fatigue
strength - Factor of safety - Gear materials – Design of straight tooth spur & helical gears
based on strength and wear considerations – Pressure angle in the normal and transverse
plane- Equivalent number of teeth-forces for helical gears.

UNIT III BEVEL, WORM AND CROSS HELICAL GEARS 9

Straight bevel gear: Tooth terminology, tooth forces and stresses, equivalent number of teeth.
Estimating the dimensions of pair of straight bevel gears.
Worm Gear: Merits and demerits- terminology. Thermal capacity, materials-forces and
stresses, efficiency, estimating the size of the worm gear pair.
Cross helical: Terminology-helix angles-Estimating the size of the pair of cross helical gears.

UNIT IV GEAR BOXES 9

Geometric progression - Standard step ratio - Ray diagram, kinematics layout -Design of sliding
mesh gear box -Constant mesh gear box. – Design of multi speed gear box for machine tool
applications – Variable speed gear box, Fluid Couplings, Torque Converters for automotive
applications.

UNIT V CAMS CLUTCHES AND BRAKES 9

Cam Design: Types-pressure angle and under cutting base circle determination-forces and
surface stresses. Design of plate clutches –axial clutches-cone clutches-internal expanding
rim clutches-shoe and band brakes - external shoe brakes – Internal expanding shoe brake -
Electromagnetic clutches
TOTAL : 45 PERIODS
Note: (Use of P S G Design Data Book is permitted in the University examination)
OUTCOMES:
• Upon completion of this course, the students can able to successfully design transmission
components used in Engine and machines

66
TEXT BOOK:
1. Bhandari V, “Design of Machine Elements”, 3rd Edition, Tata McGraw-Hill Book Co, 2010.

REFERENCES:
1. Sundararajamoorthy T. V, Shanmugam .N, “Machine Design”, Anuradha Publications,
Chennai, 2003.
2. Joseph Shigley,Charles Mischke,Richard Budynas and Keith Nisbett “Mechanical
Engineering Design”, 8th Edition, Tata McGraw-Hill, 2008.
3. Gitin Maitra,L. Prasad “Hand book of Mechanical Design”, 2nd Edition, Tata McGraw-Hill,
2001.
4. Prabhu. T.J., “Design of Transmission Elements”, Mani Offset, Chennai, 2000.
5. C.S.Sharma, Kamlesh Purohit, “Design of Machine Elements”, Prentice Hall of India,
Pvt. Ltd., 2003.
6. Bernard Hamrock,Steven Schmid,Bo Jacobson, “Fundamentals of Machine Elements”,
2nd Edition, Tata McGraw-Hill Book Co., 2006.
7. Robert C. Juvinall and Kurt M. Marshek, “Fundamentals of Machine Design”,4th Edition,
Wiley, 2005
8. Alfred Hall, Halowenko, A and Laughlin, H., “Machine Design”, Tata McGraw-Hill Book
Co.(Schaum’s Outline), 2010
9. Orthwein W, “Machine Component Design”, Jaico Publishing Co, 2003.
10. Ansel Ugural, “Mechanical Design – An Integral Approach, 1st Edition, Tata McGraw-Hill
Book Co, 2003.
11. Merhyle F. Spotts, Terry E. Shoup and Lee E. Hornberger, “Design of Machine Elements”
8th Edition, Printice Hall, 2003.

STANDARDS:
1. IS 4460 : Parts 1 to 3 : 1995, Gears – Spur and Helical Gears – Calculation of Load
Capacity.
2. IS 7443 : 2002, Methods of Load Rating of Worm Gears
3. IS 15151: 2002, Belt Drives – Pulleys and V-Ribbed belts for Industrial applications –
PH, PJ, PK, Pl and PM Profiles : Dimensions
4. IS 2122 : Part 1: 1973, Code of practice for selection, storage, installation and
maintenance of belting for power transmission : Part 1 Flat Belt Drives.
5. IS 2122: Part 2: 1991, Code of practice for selection, storage, installation and maintenance
of belting for power transmission: Part 2 V-Belt Drives.

67
 ME8651 HEAT AND MASS TRANSFER LTPC
3104
OBJECTIVES:
• To understand the mechanisms of heat transfer under steady and transient conditions.
• To understand the concepts of heat transfer through extended surfaces.
• To learn the thermal analysis and sizing of heat exchangers and to understand the basic
concepts of mass transfer.

UNIT I CONDUCTION 8+3

General Differential equation of Heat Conduction– Cartesian and Polar Coordinates – One
Dimensional Steady State Heat Conduction –– plane and Composite Systems – Conduction
with Internal Heat Generation – Extended Surfaces – Unsteady Heat Conduction – Lumped
Analysis –Semi Infinite and Infinite Solids –Use of Heisler’s charts. One dimensional Numerical
analysis in conduction.

UNIT II CONVECTION 7+3

Boundary Layer Concept – Forced Convection : External Flow – Flow over Plates, Cylinders
Spheres and Bank of tubes, Internal Flow – Entrance effects. Free Convection – Flow over
Vertical Plate, Horizontal Plate, Inclined Plate, Cylinders and Spheres.

UNIT III PHASE CHANGE HEAT TRANSFER AND HEAT EXCHANGERS 9+3
Nusselt’s theory of condensation- Regimes of Pool boiling and Flow boiling, correlations in
boiling and condensation. Heat Exchanger Types - Overall Heat Transfer Coefficient – Fouling
Factors - Analysis – LMTD method - NTU method.TEMA Standards-Introduction

UNIT IV RADIATION 9+3

Black Body Radiation – Grey body radiation - Shape Factor – Electrical Analogy – Radiation
Shields. Radiation through gases.

UNIT V MASS TRANSFER 6+3

Basic Concepts – Diffusion Mass Transfer – Fick’s Law of Diffusion – Steady state Molecular
Diffusion – Convective Mass Transfer – Momentum, Heat and Mass Transfer Analogy –
Convective Mass Transfer Correlations.
L : 45 , T : 15, TOTAL : 60 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to understand and apply different
heat and mass transfer principles of different applications.

TEXT BOOK:
1. Yunus A. Cengel, Heat Transfer A Practical Approach – Tata McGraw Hill - 2010
REFERENCE BOOKS:
1. Frank P. Incropera and David P. Dewitt, Fundamentals of Heat and Mass Transfer, John
Wiley & Sons, 1998. 68
2. S.P. Venkateshan, Heat Transfer, Ane Books, New Delhi, 2004.
3. Ghoshdastidar, P.S, Heat Transfer, Oxford, 2004,
4. Nag, P.K., Heat Transfer, Tata McGraw Hill, New Delhi, 2002
5. Holman, J.P., Heat and Mass Transfer, Tata McGraw Hill, 2000
6. Ozisik, M.N., Heat Transfer, McGraw Hill Book Co., 1994.
7. Kothandaraman, C.P., Fundamentals of Heat and Mass Transfer, New Age International,
New Delhi, 1998.
8. Yadav, R., Heat and Mass Transfer, Central Publishing House, 1995.

ME8652 INDUSTRIAL MANAGEMENT LTPC

3003
OBJECTIVES:
• To develop modern concepts of Industrial Management

UNIT I INTRODUCTION 9
Technology Management - Definition – Functions – Evolution of Modern Management –
Scientific management Development of management Thought. Approaches to the study
of management, Forms of organization – Individual Ownership- partnership – Joint Stock
companies – co-operative Enterprises- Public sector Undertakings, Corporate frame Work
– Share Holders- Board of Directors- Committees – Chief Executive – Line and functional
Managers, Constraints – Environmental – Financial – Legal- Trade Union

UNIT II FUNCTIONS OF MANAGEMENT 9

Planning – nature and purpose – objectives – strategies – policies and planning premises
– Decision making – Organizing – Nature and process – premises – Departmentalization
– line and staff – Decentralization – organizational culture, Staffing – selection and training
– placement – performance appraisal – career strategy – organizational development.
Leading managing human factor – Leadership – communication, Controlling – process of
Controlling – Controlling Techniques – productivity and inventory management systems-Tools
of Techniques– Prevention control, industrial safety

UNIT III ORGANIZATIONAL BEHAVIOUR 9

Definition – Organization – Managerial Role and functions – organizational approaches,
individual behavior – causes – Environmental Effect – Behavior and performance, perception
– organizational Implications. Personality – Contributing factors – Dimension – Need Theories
– process Theories – Job satisfaction, Learning and Behavior- Learning Curves, work design
and approaches

69
 UNIT IV GROUP DYNAMICS 9
Group Behavior – Groups – Contributing factors – Group Norms, Communication – Process
– Barriers to communication – Effective Communication, leadership- Formal and informal
characteristics- Managerial Grid – Leadership Styles – Group Decision making – Leadership
Role in Group Decision, Group Conflicts – Types – Causes – Conflict Resolution – Inter group
relations and conflict, Organizational centralization and decentralization – Formal and informal
– organizational structures – organizational change and development – Change process –
Resistance to change – culture and ethics

UNIT V MODERN CONCEPTS 9

Management by objectives (MBO) – Strategic Management – SWOT analysis – Evolving
development strategies, information technology in management – Decision support system –
Management Games – Business Process Re-engineering (BPR) – supply chain management
(SCM) –Global Perspective – Principles and Steps – Advantages and Disadvantages
TOTAL : 45 PERIODS
OUTCOMES :
 Students gain knowledge on the basic management principles to become management(s)
professional.

TEXT BOOKS:
1. Herald Koontz and Heinz Weihrich, ‘Essentials of Management’, McGraw Hill Publishing
Company, Singapore International Edition, 1980.
2. M.Govindarajan and S.Natarajan, Principles of Management, Prentice Hall of India Pvt.
Ltd. New Delhi 2007

REFERENCE BOOKS:
1. S.Chandran, Organizational Behaviors, Vikas Publishing House Pvt., Ltd, 1994
2. Ties, AF,Stoner and R.Edward Freeman, ‘Management’ Prentice Hall of India Pvt. Ltd.
New Delhi 110011, 1992.
3. Joseph J,Massie, ‘Essentials of Management’ Prentice Hall of India. Ltd.1985

ME8653 MECHATRONICS LTPC

3003
OBJECTIVES:
• This syllabus is formed to impart knowledge for the students about the elements
and techniques involved in Mechatronics systems which are very much essential to
understand the emerging field of automation.

70
 UNIT I INTRODUCTION 12
Introduction to Mechatronics – Systems – Concepts of Mechatronics approach – Need for
Mechatronics – Emerging areas of Mechatronics – Classification of Mechatronics.
Sensors and Transducers: Static and dynamic Characteristics of Sensor, Potentiometers –
LVDT – Capacitance sensors – Strain gauges – Eddy current sensor – Hall effect sensor –
Temperature sensors – Light sensors

UNIT II 8085 MICROPROCESSOR 8

Introduction – Architecture of 8085 – Pin Configuration – Addressing Modes –Instruction set,
Timing diagram of 8085.
UNIT III PROGRAMMABLE PERIPHERAL INTERFACE 10
Introduction – Architecture of 8255, Keyboard interfacing, LED display –interfacing, ADC and
DAC interface, Temperature Control – Stepper Motor Control – Traffic Control interface.

UNIT IV PROGRAMMABLE LOGIC CONTROLLER 7

Introduction – Basic structure – Input and output processing – Programming – Mnemonics –
Timers, counters and internal relays – Data handling – Selection of PLC.

UNIT V ACTUATORS AND MECHATRONIC SYSTEM DESIGN 8

Types of Stepper and Servo motors – Construction – Working Principle – Advantages and
Disadvantages. Design process-stages of design process – Traditional and Mechatronics
design concepts – Case studies of Mechatronics systems – Pick and place Robot – Engine
Management system – Automatic car park barrier.
TOTAL : 45 PERIODS
OUTCOMES:
• Upon completion of this course, the students can able to design mechatronics system with
the help of Microprocessor, PLC and other electrical and Electronics Circuits.

TEXT BOOKS:
1. Bolton, “Mechatronics”, Printice Hall, 2008
2. Ramesh S Gaonkar, “Microprocessor Architecture, Programming, and Applications with
the 8085”, 5th Edition, Prentice Hall, 2008.

REFERENCES:
1. Michael B.Histand and Davis G.Alciatore, “Introduction to Mechatronics and
Measurement systems”, McGraw Hill International edition, 2007.
2. Bradley D.A, Dawson D, Buru N.C and Loader A.J, “Mechatronics”, Chapman and
Hall, 1993.
3. Smaili.A and Mrad.F , “Mechatronics Integrated Technologies for Intelligent
Machines”,Oxford University Press, 2007.
71
 4. Devadas Shetty and Richard A. Kolk, “Mechatronics Systems Design”, PWS
publishing company, 2007.
5. Krishna Kant, “Microprocessors & Microcontrollers”, Prentice Hall of India, 2007.

HS8561 EMPLOYABILITY SKILLS LTPC

(Lab / Practical Course) 0021
(Common to all branches of Fifth or Sixth Semester B.E / B.Tech programmes)

OBJECTIVES
• To enhance the employability skills of students with a special focus on
Presentation skills, Group discussion skills and Interview skills
• To help them improve their soft skills, including report writing, necessary for the
workplace situations
1. Making presentations – introducing oneself – introducing a topic – answering
questions – individual presentation practice
2. Creating effective PPTs – presenting the visuals effectively
3. Using appropriate body language in professional contexts – gestures, facial
expressions, etc.
4. Preparing job applications - writing covering letter and résumé
5. Applying for jobs online - email etiquette
6. Participating in group discussions – understanding group dynamics - brainstorming
the topic
7. Training in soft skills - persuasive skills – People skills - questioning and clarifying
skills – mock GD
8. Writing Project proposals – collecting, analyzing and interpreting data / drafting the
final report
9. Attending job interviews – answering questions confidently
10. Interview etiquette – dress code – body language – mock interview
TOTAL: 30 PERIODS
OUTCOME
 The students will have enough confidence to present themselves well using proper oral and
written communication skills to any interview (or) discussion (or) presentation.

REFERENCE BOOKS:
1. Dhanavel, S.P. 2010. English and Soft Skills. Hyderabad: Orient BlackSwan Ltd.
2. Corneilssen, Joep. How to Prepare for Group Discussion and Interview. New
Delhi: Tata-McGraw-Hill, 2009.
3. D’Abreo, Desmond A. Group Discussion and Team Building. Mumbai: Better Yourself
Books, 2004. 72
4. Ramesh, Gopalswamy, and Mahadevan Ramesh. The ACE of Soft Skills. New
Delhi: Pearson, 2010.
5. Gulati, Sarvesh. Corporate Soft Skills. New Delhi: Rupa and Co. 2006.
6. Van Emden, Joan, and Lucinda Becker. Presentation Skills for Students. New
York: Palgrave Macmillan, 2004.

EXTENSIVE READERS
1. Covey, Stephen R. The 7 Habits of Highly Effective People. New York: Free Press, 1989.
2. Bagchi, Subroto. The Professional. New Delhi: Penguin Books India, 2009.

WEB RESOURCES
1. www.humanresources.about.com
2. www.careerride.com

ME8611 CAD / CAM LAB LTPC

0032

OBJECTIVES:
• To gain practical experience in handling 2D drafting and 3D modelling software systems.
• To study the features of CNC Machine Tool.
• To expose students to modern control systems (Fanuc, Siemens etc.,)
• To know the application of various CNC machines like CNC lathe, CNC Vertical Machining
centre, CNC EDM and CNC wire-cut and studying of Rapid prototyping.

1. 3D GEOMETRIC MODELLING 24 PERIODS

LIST OF EXPERIMENTS
1. Introduction of 3D Modelling software

Creation of 3D assembly model of following machine elements using 3D Modelling

software
2. Flange Coupling
3. Plummer Block
4. Screw Jack
5. Lathe Tailstock
6. Universal Joint
7. Machine Vice
8. Stuffing box 73
 9. Crosshead
10. Safety Valves
11. Non-return valves
12. Connecting rod
13. Piston
14. Crankshaft

2. MANUAL PART PROGRAMMING. 21 PERIODS

(i) Part Programming - CNC Machining Centre
a) Linear Cutting.
b) Circular cutting.
c) Cutter Radius Compensation.
d) Canned Cycle Operations.
(ii) Part Programming - CNC Turning Centre
a) Straight, Taper and Radius Turning.
b) Thread Cutting.
c) Rough and Finish Turning Cycle.
d) Drilling and Tapping Cycle.

3. COMPUTER AIDED PART PROGRAMMING

e) CL Data and Post process generation using CAM packages.
f) Application of CAPP in Machining and Turning Centre.

4. STUDY OF CNC EDM, CNC EDM WIRE-CUT AND RAPID PROTOTYPING.

TOTAL: 45 PERIODS
OUTCOMES
 Ability to develop 2D and 3D models using modeling softwares.
 Ability to understand the CNC control in modern manufacturing system.
 Ability to prepare CNC part programming and perform manufacturing.

ME8612 CREATIVE AND INNOVATIVE PROJECT LTPC

0032
The goal of this course is to help students to 74
identify innovative projects that promotes and
 inhibit creativity to explore the variables that affect creativity and innovation. By the end of the
period, students should be familiar with current thinking in their field, and able to apply the
concepts to relevant research problems or practical applications.

The goal of this course is to drive them to learn concepts, models, frameworks, and tools that
engineering graduates need in a world where creativity and innovation is fast becoming a pre-
condition for competitive advantage.

Each student will choose a nagging workplace problem or socially relavant problems
that have been difficult for them to “solve.” At the end of the semester, each or group of
students have to submit a report for evaluation.
TOTAL : 30 PERIODS
OUTCOMES:
 On Completion of the project work students will be in a position to take up any challenging
practical problems and find solution by formulating proper methodology.

ME8253 POWER PLANT ENGINEERING LTPC

3003
OBJECTIVE:
• Providing an overview of Power Plants and detailing the role of Mechanical Engineers
in their operation and maintenance.

UNIT I COAL BASED THERMAL POWER PLANTS 10

Rankine cycle - improvisations, Layout of modern coal power plant, Super Critical Boilers,
FBC Boilers, Turbines, Condensers, Steam & Heat rate, Subsystems of thermal power
plants – Fuel and ash handling, Draught system, Feed water treatment. Binary Cycles and
Cogeneration systems.

UNIT II DIESEL, GAS TURBINE AND COMBINED CYCLE POWER PLANTS 10

Otto, Diesel, Dual & Brayton Cycle - Analysis & Optimisation. Components of Diesel and Gas
Turbine power plants. Combined Cycle Power Plants. Integrated Gasifier based Combined
Cycle systems.

UNIT III NUCLEAR POWER PLANTS 7

Basics of Nuclear Engineering, Layout and subsystems of Nuclear Power Plants, Working
of Nuclear Reactors : Boiling Water Reactor (BWR), Pressurized Water Reactor (PWR),
CANada Deuterium-Uranium reactor (CANDU), Breeder, Gas Cooled and Liquid Metal Cooled
Reactors. Safety measures for Nuclear Power plants.

UNIT IV POWER FROM RENEWABLE ENERGY 10

Hydro Electric Power Plants – Classification, Typical Layout and associated components
75
including Turbines. Principle, Construction and working of Wind, Tidal, Solar Photo Voltaic
 (SPV), Solar Thermal, Geo Thermal, Biogas and Fuel Cell power systems.

UNIT V ENERGY, ECONOMIC AND ENVIRONMENTAL

ISSUES OF POWER PLANTS 8
Power tariff types, Load distribution parameters, load curve, Comparison of site
selection criteria, relative merits & demerits, Capital & Operating Cost of different
power plants. Pollution control technologies including Waste Disposal Options for Coal
and Nuclear Power Plants.
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to understand different types of
power plant, and its functions and their flow lines and issues related to them.
 Analyse and solve energy and economic related issues in power sectors.

TEXT BOOK:
1. Power Plant Engineering, P.K. Nag, Tata McGraw – Hill Publishing Company Ltd., Third
Edition, 2008.

REFERENCES:
1. Power Plant Technology, M.M. El-Wakil, Tata McGraw – Hill Publishing Company Ltd.,
2010.
2. Power Plant Engineering, Black & Veatch, Springer, 1996.
3. Standard Handbook of Power Plant Engineering, Thomas C. Elliott, Kao Chen and
Robert C. Swanekamp, Second Edition, McGraw – Hill, 1998.
4. Renewable energy, Godfrey Boyle, Open University, Oxford University Press in
association with the Open University, 2004.

ME8701 COMPUTER INTEGRATED MANUFACTURING LTPC

3003
OBJECTIVE:
• To understand the application of computers in various aspects of Manufacturing viz.,
Design, Proper planning, Manufacturing cost, Layout & Material Handling system.

UNIT I INTRODUCTION 10
Brief introduction to CAD and CAM – Manufacturing Planning, Manufacturing control-
Introduction to CAD/CAM – Concurrent Engineering-CIM concepts – Computerised elements
of CIM system –Types of production - Manufacturing models and Metrics – Mathematical
models of Production Performance – Simple problems – Manufacturing Control – Simple
Problems – Basic Elements of an Automated system – Levels of Automation – Lean Production
and Just-In-Time Production.
76
 UNIT II PRODUCTION PLANNING AND CONTROL AND COMPUTERISED
PROCESS PLANNING 10
Process planning – Computer Aided Process Planning (CAPP) – Logical steps in Computer
Aided Process Planning – Aggregate Production Planning and the Master Production
Schedule – Material Requirement planning – Capacity Planning- Control Systems-Shop
Floor Control-Inventory Control – Brief on Manufacturing Resource Planning-II (MRP-II) &
Enterprise Resource Planning (ERP) - Simple Problems.

UNIT III CELLULAR MANUFACTURING 9

Group Technology(GT), Part Families – Parts Classification and coding – Simple Problems in
Opitz Part Coding system – Production flow Analysis – Cellular Manufacturing – Composite
part concept – Machine cell design and layout – Quantitative analysis in Cellular Manufacturing
– Rank Order Clustering Method - Arranging Machines in a GT cell – Hollier Method – Simple
Problems.

UNIT IV FLEXIBLE MANUFACTURING SYSTEM (FMS) AND AUTOMATED

GUIDED VEHICLE SYSTEM (AGVS) 8
Types of Flexibility - FMS – FMS Components – FMS Application & Benefits – FMS Planning
and Control– Quantitative analysis in FMS – Simple Problems. Automated Guided Vehicle
System (AGVS) – AGVS Application – Vehicle Guidance technology – Vehicle Management
& Safety.

UNIT V INDUSTRIAL ROBOTICS 8

Robot Anatomy and Related Attributes – Classification of Robots- Robot Control systems –
End Effectors – Sensors in Robotics – Robot Accuracy and Repeatability - Industrial Robot
Applications – Robot Part Programming – Robot Accuracy and Repeatability – Simple
Problems.
TOTAL : 45 PERIODS
OUTCOMES:
 Knowledge gained in usage of computers and software's in various manufacturing activities
 Understanding of product and process classifications in electronic automation of shop floor
 Knowledge in FMS and AGVS in manufacturing automation
 Usage of Robots and programming of Robots

TEXT BOOK:
1. Mikell.P.Groover “Automation, Production Systems and Computer Integrated
Manufacturing”, Prentice Hall of India, 2008.

REFERENCES:
1. Kant Vajpayee S, “Principles of Computer Integrated Manufacturing”, Prentice Hall
India, 2003.
2. Radhakrishnan P, Subramanyan S.and Raju V., “CAD/CAM/CIM”, 2nd Edition, New
Age International (P) Ltd, New Delhi, 2000.
77
3. Gideon Halevi and Roland Weill, “Principles of Process Planning – A Logical
Approach” Chapman & Hall, London, 1995.
4. P Rao, N Tewari & T.K. Kundra, “Computer Aided Manufacturing”, Tata McGraw Hill
Publishing Company, 2000.

ME8752 FINITE ELEMENT ANALYSIS LTPC

3003
OBJECTIVES:
• To introduce the concepts of Mathematical Modeling of Engineering Problems.
• To appreciate the use of FEM to a range of Engineering Problems.

UNIT I INTRODUCTION 9
Historical Background – Mathematical Modeling of field problems in Engineering – Governing
Equations – Discrete and continuous models – Boundary, Initial and Eigen Value problems
– Weighted Residual Methods – Variational Formulation of Boundary Value Problems – Ritz
Technique – Basic concepts of the Finite Element Method.

UNIT II ONE-DIMENSIONAL PROBLEMS 9

One Dimensional Second Order Equations – Discretization – Element types- Linear and
Higher order Elements – Derivation of Shape functions and Stiffness matrices and force
vectors- Assembly of Matrices - Solution of problems from solid mechanics and heat transfer.
Longitudinal vibration frequencies and mode shapes. Fourth Order Beam Equation –
Transverse deflections and Natural frequencies of beams.

UNIT III TWO DIMENSIONAL SCALAR VARIABLE PROBLEMS 9

Second Order 2D Equations involving Scalar Variable Functions – Variational formulation –
Finite Element formulation – Triangular elements – Shape functions and element matrices and
vectors. Application to Field Problems - Thermal problems – Torsion of Non circular shafts –
Quadrilateral elements – Higher Order Elements.

UNIT IV TWO DIMENSIONAL VECTOR VARIABLE PROBLEMS 9

Equations of elasticity – Plane stress, plane strain and axisymmetric problems – Body forces
and temperature effects – Stress calculations - Plate and shell elements.

UNIT V ISOPARAMETRIC FORMULATION AND ADVANCED TOPICS 9

Natural co-ordinate systems – Isoparametric elements – Shape functions for isoparametric
elements – One and two dimensions – Serendipity elements – Numerical integration and
application to plane stress problems - Matrix solution techniques – Solutions Techniques to
Dynamic problems – Introduction to Analysis Software.
TOTAL : 45 PERIODS
78
OUTCOMES:
 Upon completion of this course, the students can able to understand different mathematical
Techniques used in FEM analysis and use of them in Structural and thermal problem

TEXT BOOK:
1. J.N.Reddy, “An Introduction to the Finite Element Method”, 3rd Edition, Tata McGraw-
Hill, 2005

REFERENCE BOOKS:
1. Seshu, P, “Text Book of Finite Element Analysis”, Prentice-Hall of India Pvt. Ltd., New
Delhi, 2007.
2. Logan, D.L., “A first course in Finite Element Method”, Thomson Asia Pvt. Ltd., 2002
3. Robert D. Cook, David S. Malkus, Michael E. Plesha, Robert J. Witt, “Concepts and
Applications of Finite Element Analysis”, 4th Edition, Wiley Student Edition, 2002.
4. Rao, S.S., “The Finite Element Method in Engineering”, 3rd Edition, Butter worth
Heinemann, 2004
5. Chandrupatla & Belagundu, “Introduction to Finite Elements in Engineering”, 3rd Edition,
Prentice Hall College Div, 1990

ME8661 MECHATRONICS LABORATORY LTPC

0032
OBJECTIVE:
• To know the method of programming the microprocessor and also the design, modelling
& analysis of basic electrical, hydraulic & pneumatic Systems which enable the students
to understand the concept of mechatronics.

LIST OF EXPERIMENTS:
1. Assembly language programming of 8085 – Addition – Subtraction – Multiplication –
Division – Sorting – Code Conversion.
2. Stepper motor interface.
3. Traffic light interface.
4. Speed control of DC motor.
5. Study of various types of transducers.
6. Study of hydraulic, pneumatic and electro-pneumatic circuits.
7. Modelling and analysis of basic hydraulic, pneumatic and electrical circuits using
‘AUTOMATION STUDIO’ Software.
8. Study of PLC and its applications.
9. Study of image processing technique.
TOTAL : 45 PERIODS
OUTCOMES:
• Upon completion of this course, the students can able to design mechatronics system with
79
the help of Microprocessor, PLC and other electrical and Electronics Circuits.
 ME8711 SIMULATION AND ANALYSIS LABORATORY LTPC
0032
OBJECTIVES:
• To give exposure to software tools needed to analyze engineering problems.
• To expose the students to different applications of simulation and analysis tools.

A. SIMULATION
1. MATLAB basics, Dealing with matrices, Graphing-Functions of one variable and
two variables
2. Use of Matlab to solve simple problems in vibration and Laplace Transforms
3. Simple Mechanism Simulation using commercially available software –
Demonstration only
B. ANALYSIS
1. Force and Stress analysis using link elements in Trusses, cables etc.
2. Stress and deflection analysis in beams with different support conditions.
3. Stress analysis of flat plates and simple shells.
4. Stress analysis of axi – symmetric components.
5. Thermal stress and heat transfer analysis of plates.
6. Thermal stress analysis of cylindrical shells.
7. Vibration analysis of spring-mass systems.
8. Model analysis of Beams.
9. Harmonic, transient and spectrum analysis of simple systems.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the Students can model, analyse and simulate experiments
to meet real world system and evaluate the performance.

TEXT BOOKS:
1. The Mathworks, Inc, “The student Edition of Matlab”, student Edition, The MATLAB
curriculum series, 1997
2. Rudra Pratap, “Getting started with MATLAB”, 1st Edition, Oxford University Press, 2010

ME8811 PROJECT WORK LTPC

0 0 12 6
OBJECTIVES:
 To develop the ability to solve a specific problem right from its identification and literature
review till the successful solution of the same. To train the students in preparing project
reports and to face reviews and viva voce examination.

80
 A project topic must be selected by the students in consultation with their guides. The
aim of the project work is to deepen comprehension of principles by applying them to a new
problem which may be the design and fabrication of a device for a specific application, a
research project with a focus on an application needed by the industry/society, a computer
project, a management project or a design project.

The progress of the project is evaluated based on a minimum of three reviews. The
review committee may be constituted by the Head of the Department. A project report is
required at the end of the semester. The project work is evaluated jointly by external and
internal examiners constituted by the Head of the Department based on oral presentation
and the project report.

OUTCOMES:
 On Completion of the project work students will be in a position to take up any challenging
practical problems and find solution by formulating proper methodology.

ME8001 ADVANCED INTERNAL COMBUSTION ENGINEERING LTPC

3003
OBJECTIVES:
• To understand the underlying principles of operation of different IC Engines and
components.
• To provide knowledge on pollutant formation, control, alternate fuel etc.

UNIT I SPARK IGNITION ENGINES 9

Mixture requirements – Fuel injection systems – Monopoint, Multipoint & Direct injection -
Stages of combustion – Normal and Abnormal combustion – Knock - Factors affecting knock
– Combustion chambers.

UNIT II COMPRESSION IGNITION ENGINES 9

Diesel Fuel Injection Systems - Stages of combustion – Knocking – Factors affecting knock –
Direct and Indirect injection systems – Combustion chambers – Fuel Spray behaviour – Spray
structure and spray penetration – Air motion - Introduction to Turbocharging.

UNIT III POLLUTANT FORMATION AND CONTROL 9

Pollutant – Sources – Formation of Carbon Monoxide, Unburnt hydrocarbon, Oxides of
Nitrogen, Smoke and Particulate matter – Methods of controlling Emissions – Catalytic
converters, Selective Catalytic Reduction and Particulate Traps – Methods of measurement –
Emission norms and Driving cycles.

81
 UNIT IV ALTERNATIVE FUELS 9
Alcohol, Hydrogen, Compressed Natural Gas, Liquefied Petroleum Gas and Bio Diesel -
Properties, Suitability, Merits and Demerits - Engine Modifications.

UNIT V RECENT TRENDS 9

Air assisted Combustion, Homogeneous charge compression ignition engines – Variable
Geometry turbochargers – Common Rail Direct Injection Systems - Hybrid Electric Vehicles –
NOx Adsorbers - Onboard Diagnostics.
TOTAL: 45 PERIODS
OUTCOME:
• Upon completion of this course, the students can able to compare the operations of
different IC Engine and components and can evaluate the pollutant formation, control,
alternate fuel

TEXT BOOKS:
1. K.K. Ramalingam, Internal Combustion Engine Fundamentals, Scitech Publications,
2002.
2. Ganesan, Internal Combustion Engines, II Edition, TMH, 2002.

REFERENCES:
1. R.B. Mathur and R.P. Sharma, Internal Combustion Engines., Dhanpat Rai & Sons
2007.
2. Duffy Smith, Auto Fuel Systems, The Good Heart Willcox Company, Inc., 1987.
3. Eric Chowenitz, Automobile Electronics, SAE Publications, 1995

.
ME8002 CASTING AND WELDING PROCESSES LTPC
3003
OBJECTIVE:
• The objective of the course is to impart knowledge on Design of Gating system for
castings, Foundry Practice of Ferrous, Non Ferrous alloys, Foundry Mechanisation
Welding Processes and Welding Metallurgy.

UNIT I DESIGN OF GATING SYSTEM 11

Gating System design pouring Time – Choke Area – Sprue – Other gating elements – Risering
design - Caines – modulus – Naval research Laboratory method – feeding distances – Chills
feeding Aids – design of Castings.

UNIT II FERROUS AND NON FERROUS CASTINGS 10

Steel Casting – The family of cast iron – melting of steels and cast irons – Grey iron
foundry practice – Ductile iron – Malleable Iron casting design – Considerations Aluminium,
Magnesium, Copper, Zinc. ,Duplex Stainless Steel
82 and Titanium alloys foundry practice.
 UNIT III FOUNDRY MECHANISATION 8
Mechanical equipments in foundry – plant site location, layout – Plant Engineering –
Maintenance – Services – Practical aspects.
UNIT IV WELDING PROCESS AND TECHNOLOGY 8
Friction Welding Process – effect of speed and pressure – explosive welding – plasma arc
welding – Electon beam welding – High frequency induction welding - Laser beam weding.

UNIT V WELDING METALLURGY 8

Weld thermal cycles – Heat Affected Zone(HAZ) – Weldability of steels – Cast Iron – Stainless
steel, aluminium – Copper and Titanium alloys – Hydrogen embrittlement – Pro and post weld
heat Treatments – weld defects – Testing of Welds.
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to compare different types of casting
and welding process for effective casting and Welding of Structural components.

TEXT BOOK:
1. P.N.Rao , Manufacturing Technology , Tata McGraw Hill, 2008.

REFERENCES:
1. Heine , Loper and Rosenthal, Principles of Metal Casting ,Tata McGraw Hill,2001
2. A.K.Chakrabarti, Casting Technology and Cast Alloys, Prentice –Hall Of India Ltd, 2005
3. T.V.Rama Rao, Metal casting Principles and Practice, New Age International,2010
4. R.S Parmar, Welding Engineering and Technology, Khanna Publishers,2002

ME8003 COMPOSITE MATERIALS AND MECHANICS LTPC

3003
OBJECTIVES
• To understand the fundamentals of composite material strength and its mechanical
behavior.
• To understand fabrication and properties of different composites
• Combinations of plies with different orientations of the fiber.
• Thermo-mechanical behavior and study of residual stresses in Laminates during
processing. Implementation of Classical Laminate Theory (CLT) to study and analysis
for residual stresses in an isotropic layered structure such as electronic chips.

UNIT I INTRODUCTION TO COMPOSITE MATERIALS 10

Definition-Matrix materials-polymers-metals-ceramics - Reinforcements: Particles, whiskers,
inorganic fibers, metal filaments- ceramic fibers- fiber fabrication- natural composite wood, Jute
83
- Advantages and drawbacks of composites over monolithic materials. Mechanical properties
and applications of composites, Particulate-Reinforced composite Materials, Dispersion-
Strengthened composite, Fiber-reinforced composites Rule of mixtures-Characteristics of
fiber-Reinforced composites, Manufacturing fiber and composites,

UNIT II PROCESSING OF COMPOSITES 10

Processing of PMCs-handlay-up, spray technique, filament winding,Pultrusion,RTM, bag
molding, injection moulding,SMC -Processing of MMCs-solid state, liquid state,vapour
state processing, Processing of CMCs –hot pressing-reaction bonding process-infiltration
technique, direct oxidation- interfaces

UNIT III INTRODUCTION, LAMINA CONSTITUTIVE EQUATIONS 12

Lamina Constitutive Equations: Lamina Assumptions – Macroscopic Viewpoint. Generalized
Hooke’s Law. Reduction to Homogeneous Orthotropic Lamina – Isotropic limit case, Orthotropic
Stiffness matrix (Q ), ij Definition of stress and Moment Resultants. Strain Displacement
relations. Basic Assumptions of Laminated anisotropic plates. Laminate Constitutive Equations
– Coupling Interactions, Balanced Laminates, Symmetric Laminates, Angle Ply Laminates,
Cross Ply Laminates. Laminate Structural Moduli.
Evaluation of Lamina Properties from Laminate Tests. Quasi-Isotropic Laminates. Determination
of Lamina stresses within Laminates.

UNIT IV LAMINA STRENGTH ANALYSIS 5

Introduction - Maximum Stress and Strain Criteria. Von-Misses Yield criterion for Isotropic
Materials. Generalized Hill’s Criterion for Anisotropic materials. Tsai-Hill’s Failure Criterion
for Composites. Tensor Polynomial (Tsai-Wu) Failure criterion. Prediction of laminate Failure

UNIT V THERMAL ANALYSIS 8

Assumption of Constant Co-efficient of Thermal Expansion (C.T.E.) - Modification of Hooke’s
Law. Modification of Laminate Constitutive Equations. Orthotropic Lamina C.T.E’s. C.T.E’s for
special Laminate Configurations – Unidirectional, Off-axis, Symmetric Balanced Laminates, Zero
C.T.E laminates, Thermally Quasi-Isotropic Laminates
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to analyse the fiber reinforced
Laminate for optimum design
 Apply classical laminate theory to study and analyse the residual stresses in Laminate.

TEXT BOOKS:
1. Gibson, R.F., Principles of Composite Material Mechanics, McGraw-Hill, Second Edition
- CRC press in progress, 1994
2. Krishnan K.Chawla , Composite Materials:Science and Engineering, Springer, Second
Edition, 2008

84
REFERENCES:
1. Hyer, M.W., “Stress Analysis of Fiber – Reinforced Composite Materials”, McGraw- Hill,
1998
2. Issac M. Daniel and Ori Ishai, “Engineering Mechanics of Composite Materials”, Oxford
University Press-2006, First Indian Edition - 2007
3. Mallick, P.K., Fiber –”Reinforced Composites: Materials, Manufacturing and Design”,
Maneel Dekker Inc, 1993.
4. Halpin, J.C., “Primer on Composite Materials, Analysis”, Techomic Publishing Co., 1984.
5. Agarwal, B.D., and Broutman L.J., “Analysis and Performance of Fiber Composites”,
John Wiley and Sons, New York, 1990.
6. Mallick, P.K. and Newman, S., (edition), “Composite Materials Technology: Processes
and Properties”, Hansen Publisher, Munish, 1990.

ME8004 DESIGN OF HEAT EXCHANGERS LT P C

3003
OBJECTIVES:
• To learn the thermal and stress analysis on various parts of the heat exchangers
• To analyze the sizing and rating of the heat exchangers for various applications

UNIT I INTRODUCTION 9
Types of heat exchangers, shell and tube heat exchangers – regenerators and recuperators -
Temperature distribution and its implications - Parts description, Classification as per Tubular
Exchanger Manufacturers Association (TEMA)

UNIT II PROCESS DESIGN OF HEAT EXCHANGERS 9

Heat transfer correlations, Overall heat transfer coefficient, analysis of heat exchangers – LMTD
and effectiveness method. Sizing of finned tube heat exchangers, U tube heat exchangers,
Design of shell and tube heat exchangers, fouling factors, pressure drop calculations.

UNIT III STRESS ANALYSIS 9

Stress in tubes – header sheets and pressure vessels – thermal stresses, shear stresses -
types of failures, buckling of tubes, flow induced vibration.

UNIT IV COMPACT AND PLATE HEAT EXCHANGER 9

Types- Merits and Demerits- Design of compact heat exchangers, plate heat exchangers,
performance influencing parameters, limitations.

85
 UNIT V CONDENSERS AND COOLING TOWERS 9
Design of surface and evaporative condensers – cooling tower – performance characteristics.
TOTAL: 45 PERIODS
OUTCOMES:
• Upon completion of this course, the students can able to apply the mathematical knowledge
for thermal and stress analysis on various parts of the heat exchangers components.

TEXT BOOKS:

1. SadikKakac and Hongtan Liu, Heat Exchangers Selection, Rating and Thermal Design,
CRC Press, 2002.
2. Shah,R. K., Dušan P. Sekulić, Fundamentals of heat exchanger design, John Wiley &
Sons,2003.

REFERENCES:
1. Robert W. Serth, Process heat transfer principles and applications, Academic press,
Elesevier, 2007.
2. Sarit Kumar Das, Process heat transfer, Alpha Science International, 2005
3. John E. Hesselgreaves,Compact heat exchangers: selection, design, and operation,
Elsevier science Ltd, 2001.
4. T. Kuppan, Heat exchanger design hand book, New York : Marcel Dekker, 2000.
5. Eric M. Smith, Advances in thermal design of heat exchangers: a numerical approach:
direct-sizing, step-wise rating, and transients, John Wiley & Sons, 1999.
6. Arthur. P Frass, Heat Exchanger Design, John Wiley & Sons, 1989

ME8005 DESIGN OF PRESSURE VESSELS AND PIPING LTPC

3003
OBJECTIVES:
 To understand the Mathematical knowledge to design pressure vessels and piping
 To understand the ability to carry of stress analysis in pressure vessels and piping

UNIT I INTRODUCTION 3
Methods for determining stresses – Terminology and Ligament Efficiency – Applications.

UNIT II STRESSES IN PRESSURE VESSELS 15

Introduction – Stresses in a circular ring, cylinder –Dilation of pressure vessels, Membrane
stress Analysis of Vessel – Cylindrical, spherical and, conical heads – Thermal Stresses –
Discontinuity stresses in pressure vessels.
UNIT III DESIGN OF VESSELS 15
Design of Tall cylindrical self supporting process columns – Supports for short vertical vessels
– Stress concentration at a variable Thickness transition section in a cylindrical vessel, about
a circular hole, elliptical openings. Theory of Reinforcement – Pressure Vessel Design.
86
 UNIT IV BUCKLING AND FRACTURE ANALYSIS IN VESSELS 8
Buckling phenomenon – Elastic Buckling of circular ring and cylinders under external pressure
– collapse of thick walled cylinders or tubes under external pressure – Effect of supports on
Elastic Buckling of Cylinders – Buckling under combined External pressure and axial loading.

UNIT V PIPING 4
Introduction – Flow diagram – piping layout and piping stress Analysis.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to apply the mathematical
fundamental for the design of pressure vessels and pipes. Further they can able to analyse
and design of pressure vessels and piping.

TEXT BOOK:
1. John F. Harvey, Theory and Design of Pressure Vessels, CBS Publishers and Distributors,
1987.

REFERENCES
1. Henry H. Bedner, “Pressure Vessels, Design Hand Book, CBS publishers and
Distributors, 1987.
2. Stanley, M. Wales, “Chemical process equipment, selection and Design. Buterworths
series in Chemical Engineering, 1988.
3. William. J., Bees, “Approximate Methods in the Design and Analysis of Pressure Vessels
and Piping”, Pre ASME Pressure Vessels and Piping Conference, 1997.
4. Sam Kannapan, “Introduction to Pipe Stress Analysis”. John Wiley and Sons, 1985.

ME8006 GAS DYNAMICS AND SPACE PROPULSION LTPC

3 0 0 3
OBJECTIVES:
• To understand the differences between incompressible and compressible flow.
• To understand the phenomenon of shock waves and its effect on flow.
• To gain basic knowledge about jet propulsion and rocket propulsion.

UNIT I BASIC CONCEPTS AND ISENTROPIC FLOWS 9

Energy and momentum equations of compressible fluid flows – isentropic flow - Mach waves
and Mach cone. Flow regimes, effect of Mach number on compressibility. Stagnation, static,
critical properties and their interrelationship. Isentropic flow through variable area ducts –
nozzles and diffusers. Use of Gas tables.

87
 UNIT II FLOW THROUGH DUCTS 6
Flows through constant area ducts with heat transfer (Rayleigh flow) and Friction (Fanno flow)
– variation of flow properties. Use of tables and charts.

UNIT III NORMAL AND OBLIQUE SHOCKS 10

Governing equations - Rankine-Hugoniot Relation. Variation of flow parameters across the
normal and oblique shocks. Prandtl – Meyer expansion and relation. Use of table and charts.

UNIT IV JET PROPULSION 10

Theory of jet propulsion – thrust equation – thrust power and propulsive efficiency. Operation,
cycle analysis and performance of ram jet, turbojet, turbofan and turbo prop engines.
UNIT V SPACE PROPULSION 10
Types of rocket engines and propellants. Characteristic velocity. Theory of single and
multistage rocket propulsion. Liquid fuel feeding systems. Solid propellant geometries. Space
flights – orbital and escape velocity. Rocket performance calculations.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to successfully apply gas dynamics
principles in the Jet and Space Propulsion

TEXT BOOKS:
1. Anderson, J.D., Modern Compressible flow, McGraw Hill, 2004.
2. S.M. Yahya, Fundamentals of Compressible Flow with Aircraft and Rocket propulsion,
New Age International (P) Limited, 4th Edition, 2010.
3. Saravanamutto HIH, Cohen H., Rogers CEC. & Straznicky PV, Gas Turbine Theory, 6th
Edition, Printice Hall, 2009..
4. Sutton, G.P. Rocket Propulsion Elements, John wiley, 2010, New York

REFERENCES:
1. Radhakrishnan, E., Gas Dynamics, Printice Hall of India, 2008
2. Shapiro, Dynamics and Thermodynamics of Compressible fluid Flow, , John wiley, 1953.
3. Hill and Peterson, Mechanics and Thermodynamics of Propulsion, Addison – Wesley, 1992.
4. Zucrow, N.J., Aircraft and Missile Propulsion, vol.1 & II, John Wiley, 1975

88
 ME8007 MECHANICAL VIBRATION AND NOISE CONTROL LTPC
3003
OBJECTIVE:
• The student will be able to understand the sources of vibration and noise in automobiles
and make design modifications to reduce the vibration and noise and improve the life of
the components

UNIT I BASICS OF VIBRATION 9

Introduction, classification of vibration: free and forced vibration, undamped and damped
vibration, linear and non linear vibration, response of damped and undamped systems under
harmonic force, analysis of single degree and two degree of freedom systems, torsional
vibration, determination of natural frequencies.

UNIT II BASICS OF NOISE 9

Introduction, amplitude, frequency, wavelength and sound pressure level, addition, subtraction
and averaging decibel levels, noise dose level, legislation, measurement and analysis of
noise, measurement environment, equipment, frequency analysis, tracking analysis, sound
quality analysis.

UNIT III AUTOMOTIVE NOISE SOURCES 9

Noise Characteristics of engines, engine overall noise levels, assessment of combustion
noise, assessment of mechanical noise, engine radiated noise, intake and exhaust noise,
engine necessary contributed noise, transmission noise, aerodynamic noise, tire noise, brake
noise.

UNIT IV CONTROL TECHNIQUES 9

Vibration isolation, tuned absorbers, un-tuned viscous dampers, damping treatments,
application dynamic forces generated by IC engines, engine isolation, crank shaft damping,
modal analysis of the mass elastic model shock absorbers.

UNIT V SOURCE OF NOISE AND CONTROL 9

Methods for control of engine noise, combustion noise, mechanical noise, predictive analysis,
palliative treatments and enclosures, automotive noise control principles, sound in enclosures,
sound energy absorption, sound transmission through barriers
TOTAL: 45 PERIODS
OUTCOMES:
 Understanding causes, source and types of vibrations in machineries
 Gaining knowledge in sources and measurement standard of noise
 Ability to design and develop vibrations and noise control systems.

TEXT BOOKS:
1. Singiresu S.Rao - “Mechanical Vibrations”, 5th Edition, Pearson Education, 2010
89
REFERENCES:
1. Benson H. Tongue, “Principles of Vibrations”, 2nd Edition, Oxford University, 2007
2. David Bies and Colin Hansen, “Engineering Noise Control – Theory and Practice”,4th
Edition, E and FN Spon, Taylore& Francise e-Library, 2009
3. William T. Thomson, Marie Dillon Dahleh, Chandramouli Padmanabhan, “Theory of
Vibration with Application”, 5th edition Pearson Education, 2011
4. Grover. G.T., “Mechanical Vibrations”, Nem Chand and Bros., 1996
5. Bernard Challen and Rodica Baranescu - “Diesel Engine Reference Book” – Second
Edition - SAE International - ISBN 0-7680-0403-9 – 1999.
6. Julian Happian-Smith - “An Introduction to Modern Vehicle Design”- Butterworth-
Heinemann, ISBN 0750-5044-3 – 2004
7. Rao, J.S and Gupta, K., “Introductory course on Theory and Practice of Mechanical
Vibration”, 2nd Edition, New Age International Publications, 2010
8. A.A. Shabana, “Theory of vibrations – An introduction”, 2nd Edition, Springer, 2010
9. Balakumar Balachandran and Edward B. Magrab, “Fundamentals of Vibrations”, 1st
Editon, Cengage Learning, 2009
10. John Fenton, “Handbook of Automotive body Construction and Design Analysis –
Professional Engineering Publishing, ISBN 1-86058-073- 1998.

ME8008 THEORY OF METAL FORMING LTPC

3003
OBJECTIVES:
• This course aims to impart the knowledge about various metal forming processes. It
deals with metal forming concepts like theory of plasticity and special metal forming
techniques. After this course a student will have a good exposure about this subject.
This also gives the recent trends in the metal forming processes.

UNIT I THEORY OF PLASTICITY 9

Theory of plastic deformation – Engineering stress and strain relationship – Strain rate –
Stress tensor – Strain tensor – Yield criteria – Plastic stress strain relationship – Plastic work
– Plastic anisotropy.
UNIT II CONSTITUTIVE RELATIONSHIPS AND INSTABILITY 7
Uniaxial tension test – Mechanical properties – Work hardening, Compression test, bulge
test, plane strain compression, plastic instability in uniaxial tension stress, plastic instability
in biaxial tension stress – Material models – Elasto plasticity, Rigid plasticity, visco plasticity.

UNIT III ANALYSIS OF METAL FORMING 12

Slab analysis – Slip line method, upper bound solutions, numerical methods, contact
problems, effect of friction, thermo elastic- analysis
90 of forging, rolling, extrusion and wire
 drawing processes – forming load – Net and Near net shape forming – Cold and Hot Forging.

UNIT IV SHEET METAL FORMING 8

Sheet Metal Forming methods – Bending – Drawing – Deep Drawing – Stretch Forming –
Formability and workability – Forming limit diagram – Analysis of Sheet Metal Forming – HERF
Techniques – Principles and Process Parameters – Superplastic Forming.

UNIT V SPECIAL METAL FORMING PROCESSES 9

Orbital forging, Isothermal forging, Warm forging, Hot and Cold isotrophical pressing, high
speed extrusion, rubber pad forming, micro blanking – Overview of Powder Metal Techniques
– Powder rolling.
TOTAL : 45 PERIODS
OUTCOMES:
 Students will learn how to determine the loading of the forming tool or machine, and how
to determine the critical values of deformation

TEXT BOOKS:
1. Dieter G.E, “Mechanical Metallurgy” Mc Graw – Hill Co. S1. Edition 1995
2. Surender Kumar, “Technology of Metal Forming Processes”, PHI, New Delhi, 2008.

REFERENCES:
1 Nagpal G.R “Metal Forming Process”, Kanna Pub, New Delhi – 2000.
2 Wagoner, R.H and Chenot, JJ Metal Forming Analysis, Cambridge University Press,
2002.
3 Slater, R.A.C., Engineering Plasticity – Theory and Applications to Metal Forming, John
Wiely and Sons, 1987.
4 Shiro Kobayshi, Altan. T, Metal Forming and Finite Element Method, Oxford University
Press, 1989.
5 Hosford, W.F and Caddell, R.M., Metal Forming Mechanics and Metallurgy, Prentice
Hall Eaglewood Cliffs, 1993.
6 Narayanaswamy. R, Theory of Metal Forming and Plasticity Narosa Publishers, 1999.
7 Kurt Lange, “Handbook of Metal Forming”, Society of Manufacturing Engineers,
Michigan, USA, 1988.
8 Avitzur, “Metal Forming – Process and Analysis”, Tata McGraw-Hill Co., New Delhi,
1977.

91
 ME8009 TURBO MACHINERY LTPC
3003
OBJECTIVE:
• To understand the operating principles of various turbomachines and analyse their use
for various engineering applications.

UNIT I PRINCIPLES 9
Classification of Turbomachines. Energy transfer between fluid and rotor - Euler equation and
its interpretation. Velocity triangles. Thermal, Mechanical and overall efficiencies. Polytropic
efficiency. Degree of reaction. Dimensionless parameters for Turbomachines.

UNIT II CENTRIFUGAL FANS AND BLOWERS 9

Types – components – working. Flow analysis in impeller blades-volute and diffusers. Velocity
triangles - h-s diagram. Performance characteristic curves – various losses.

UNIT III CENTRIFUGAL COMPRESSOR 9

Construction details - Impeller types. Velocity triangles - h-s diagram. slip factor and power
input factor. Performance characteristics and various losses. Geometry and performance
calculation.

UNIT IV AXIAL FLOW COMPRESSOR 9

Construction details. Work done factor. Stage velocity diagrams - h-s diagram. Performance
characteristics, efficiency and stage losses.

UNIT V AXIAL AND RADIAL FLOW TURBINES 9

Stage velocity diagrams - impulse and reaction stages. Performance coefficients and losses.
Multistaging. Optimum conditions. Performance characteristics.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to explain the various systems,
principles and applications and different types of turbo machinery components.

TEXT BOOKS:
1. Yahya, S.H., Turbines, Compressor and Fans, 3rd Edition, Tata McGraw Hill, 2005.
2. Ganesan, V., Gas Turbines, Tata McGraw Hill Pub. Co.2010.
3. Saravanamutto HIH, Cohen H., Rogers CEC. & Straznicky PV, Gas Turbine Theory, 6th
Edition, Printice Hall, 2009.

REFERENCES:
1. Bruneck, Fans, Pergamom Press, 1973.
2. Dixon, S.I., Fluid Mechanics and Thermodynamics of Turbomachinery, Pergamon Press,
1990. 92
 3. Shepherd, D.G., Principles of Turbomachinery, Macmillan, 1969.
4. Stepanoff, A.J., Blowers and Pumps, John Wiley and Sons Inc. 1965.
5. Gopalakrishnan .G and Prithvi Raj .D, A Treatise on Turbomachines, Scitech Publications
(India) Pvt. Ltd., 2002.

ME8071 AUTOMOBILE ENGINEERING LTPC

3003
OBJECTIVE:
• To provide a first course of teaching such that the learners are able to visualise the
scope of Automobile Engineering.

UNIT I INTRODUCTON TO AUTOMOTIVES 10

An overview of different types of automobiles and their power sources.Specifications,
Performance Parameters, Quality standards, Trends in automobile design.

UNIT II POWER SOURCE FEATURES 10

Reciprocating Engine systems, Rotary Engine systems, Gas Turbine systems, Hybrid
systems. Pollutant emissions and their control; Catalytic converter systems, Electronic Engine
Management systems.

UNIT III TRANSMISSION, SUSPENSION AND BREAKING SYSTEMS 10

Clutch system, Gear box system, propeller shafting, differential, axles, wheels and tyres and
prelimineries of suspension systems
UNIT IV OTHER AUXILIARY SYSTEMS 10
Electrical and electronic systems, safety systems, Heating, Ventilation, and Air Conditioning
(HVAC) systems, Vehicle Thermal Management System and vehicle body design features.

UNIT V TESTS, SERVICE AND MAINTENANCE 5

Engine Tuning, vehicle maintenance, engine and Chassis Dynamometry Pollutants and
emissions check, Wind Tunnel Tests, preliminaries of engine and vehicle testing.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students will be able to identify the different
components in automobile engineering.
 Have clear understanding on different auxiliary and transmission systems usual.

TEXT BOOK:
1. Automotive Mechanics, William H. Crouse and Donald L. Anglin,Tata McGraw – Hill
Publishing Company Ltd., 2004, Tenth Edition.
93
REFERENCES:
1. Automotive Handbook, Bosch, Robert Bosch GmbH, Germany, 2004, Sixth Edition.
2. Automotive Technology – A Systems Approach, Jack Erjavek, Thomson Learning, 3rd
Edition, 1999.

ME8072 COMPUTATIONAL FLUID DYNAMICS LTPC

3003
OBJECTIVES:
• To introduce Governing Equations of viscous fluid flows
• To introduce numerical modeling and its role in the field of fluid flow and heat transfer
• To enable the students to understand the various discretization methods, solution
procedures and turbulence modeling.
• To create confidence to solve complex problems in the field of fluid flow and heat transfer
by using high speed computers.

UNIT I GOVERNING EQUATIONS AND BOUNDARY CONDITIONS 8

Basics of computational fluid dynamics – Governing equations of fluid dynamics – Continuity,
Momentum and Energy equations – Chemical species transport – Physical boundary conditions
– Time-averaged equations for Turbulent Flow – Turbulent–Kinetic Energy Equations –
Mathematical behaviour of PDEs on CFD - Elliptic, Parabolic and Hyperbolic equations.

UNIT II FINITE DIFFERENCE AND FINITE VOLUME METHODS FOR DIFFUSION 9

Derivation of finite difference equations – Simple Methods – General Methods for first and
second order accuracy – Finite volume formulation for steady state One, Two and Three
-dimensional diffusion problems –Parabolic equations – Explicit and Implicit schemes –
Example problems on elliptic and parabolic equations – Use of Finite Difference and Finite
Volume methods.

UNIT III FINITE VOLUME METHOD FOR CONVECTION DIFFUSION 10

Steady one-dimensional convection and diffusion – Central, upwind differencing schemes-
properties of discretization schemes – Conservativeness, Boundedness, Transportiveness,
Hybrid, Power-law, QUICK Schemes.

UNIT IV FLOW FIELD ANALYSIS 9

Finite volume methods -Representation of the pressure gradient term and continuity equation
– Staggered grid – Momentum equations – Pressure and Velocity corrections – Pressure
Correction equation, SIMPLE algorithm and its variants – PISO Algorithms.

UNIT V TURBULENCE MODELS AND MESH GENERATION 9

Turbulence models, mixing length model, Two equation (k-Є) models – High and low
94
 Reynolds number models – Structured Grid generation – Unstructured Grid generation –
Mesh refinement – Adaptive mesh – Software tools.
TOTAL: 45 PERIODS
OUTCOMES:
Upon completion of this course, the students can able
 To create numerical modeling and its role in the field of fluid flow and heat transfer
 To use the various discretization methods, solution procedures and turbulence modeling to
solve flow and heat transfer problems.

TEXT BOOKS:
1. Versteeg, H.K., and Malalasekera, W., An Introduction to Computational Fluid Dynamics:
The finite volume Method, Pearson Education Ltd. Second Edition – 2007.
2. Ghoshdastidar, P.S., Computer Simulation of flow and heat transfer, Tata McGraw Hill
Publishing Company Ltd., 1998.

REFERENCES:
1. Patankar, S.V. Numerical Heat Transfer and Fluid Flow, Hemisphere Publishing
Corporation, 2004.
2. Chung, T.J. Computational Fluid Dynamics, Cambridge University, Press, 2002.
3. Ghoshdastidar P.S., Heat Transfer, Oxford University Press, 2005
4. Muralidhar, K., and Sundararajan, T., Computational Fluid Flow and Heat Transfer,
Narosa Publishing House, New Delhi, 1995.
5. ProdipNiyogi, Chakrabarty, S.K., Laha, M.K. Introduction to Computational Fluid
Dynamics, Pearson Education, 2005.
6. Introduction to Computational Fluid Dynamics Anil W. Date Cambridge University Press,
2005.

ME8073 DESIGN FOR MANUFACTURING LTPC

3003
OBJECTIVES:
• To understand the principles of design such that the manufacturing of the product is
possible.
• To educate students on various design aspects to be considered for manufacturing the
products using different processes.

UNIT I MANUFACTURING METHODOLOGY AND PROCESESS 9

Methodologies and tools, design axioms, design for assembly and evaluation, minimum
part assessment, Taguchi method, robustness assessment, manufacturing process rules,
designer’s tool kit, Computer Aided group Technology, failure mode effects analysis, Value
Analysis, Design for minimum number of parts, development of modular design, minimizing
part variations, design of parts to be multi-functional, multi-use, ease of fabrication, Poke Yoke
principles.
95
 UNIT II GEOMETRIC ANALYSIS 9
Surface finish, review of relationship between attainable tolerance grades and different
machining processes, part features-feature of size-control from-placement material condition
– MMC – LMC

UNIT III FORM DESIGN OF CASTINGS AND WELDMENTS 9

Redesign of castings based on parting line considerations, minimizing core requirements,
redesigning cast members by welded structure , use of welding symbols.

UNIT IV MECHANICAL ASSEMBLY 9

Selective assembly, deciding the number of groups, control of axial play, examples,Grouped
datum systems , different types, geometric analysis and applications, design features to
facilitate automated assembly, Assembly analysis worst case Arithmetic method, Monte -Carlo
method.
UNIT V TRUE POSITION THEORY 9
Virtual size concept, floating and fixed fasteners, projected tolerance zone, assembly with
gasket, zero true position tolerance, functional gauges, paper layout gauging,examples.
Operation sequence for typical shaft type of components. Preparation of process
drawings for different operations, tolerance worksheets and centrality analysis,
examples.
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of the subject, students will be able to
 understand the concept of mass customization and product family design;
 apply appropriate methods to achieve quality in product design;
 analyze product design for assembly, manufacturing, and end-of-life issues;
 understand how global environmental requirements affect product design;
 analyze product design in terms of environmental impact and suggest improvements.
TEXT BOOKS :
1. Harry pack, “Designing for Manufacture”, Pitman Publications, 1983.
2. Matousek, “Engineering Design, - A Systematic Approach” – Blackie & Son Ltd, London, 1974

REFERENCE BOOKS:
1. Spotts M.F. “Dimensioning and Tolerance for Quantity Production, Prentice Hall Inc.1983.
2. Oliver R. Wade, “Tolerance Control in Design and Manufacturing “. Industrial Press Inc.
New York Publications. 1967.
3. James G. Bralla. “Hand Book of Product Design for Manufacturing”. McGraw Hill
Publications, 1983.
4. Trucks H.E. “Design for Economic Production”. Society of Manufacturing Engineers,
Michigan, 2nd edition, 1987.

96
ME8074 DESIGN OF JIGS, FIXTURES AND PRESS TOOLS LTPC
3003
OBJECTIVES:
• To understand the functions and design principles of Jigs, fixtures and press tools
• To gain proficiency in the development of required views of the final design.

UNIT I LOCATING AND CLAMPING PRINCIPLES: 8

Objectives of tool design- Function and advantages of Jigs and fixtures – Basic elements –
principles of location – Locating methods and devices – Redundant Location – Principles of
clamping – Mechanical actuation – pneumatic and hydraulic actuation Standard parts – Drill
bushes and Jig buttons – Tolerances and materials used.

UNIT II JIGS AND FIXTURES 10

Design and development of jigs and fixtures for given component- Types of Jigs – Post,
Turnover, Channel, latch, box, pot, angular post jigs – Indexing jigs – General principles of
milling, Lathe, boring, broaching and grinding fixtures – Assembly, Inspection and Welding
fixtures – Modular fixturing systems- Quick change fixtures.

UNIT III PRESS WORKING TERMINOLOGIES AND

ELEMENTS OF CUTTING DIES 10
Press Working Terminologies - operations – Types of presses – press accessories –
Computation of press capacity – Strip layout – Material Utilization – Shearing action –
Clearances – Press Work Materials – Center of pressure- Design of various elements of dies
– Die Block – Punch holder, Die set, guide plates – Stops – Strippers – Pilots – Selection of
Standard parts – Design and preparation of four standard views of simple blanking, piercing,
compound and progressive dies.

UNIT IV BENDING AND DRAWING DIES 10

Difference between bending and drawing – Blank development for above operations – Types
of Bending dies – Press capacity – Spring back – knockouts – direct and indirect – pressure
pads – Ejectors – Variables affecting Metal flow in drawing operations – draw die inserts
– draw beads- ironing – Design and development of bending, forming, drawing, reverse re-
drawing and combination dies – Blank development for axisymmetric, rectangular and elliptic
parts – Single and double action dies.

UNIT V OTHER FORMING TECHNIQUES 7

Bulging, Swaging, Embossing, coining, curling, hole flanging, shaving and sizing, assembly,
fine Blanking dies – recent trends in tool design- computer Aids for sheet metal forming
Analysis – basic introduction - tooling for numerically controlled machines- setup reduction for
work holding – Single minute exchange of dies – Poka Yoke.
TOTAL: 45 PERIODS
Note: (Use of P S G Design Data Book is permitted in the University examination)
97
OUTCOMES:
 Upon completion of this course, the students can able to design jigs, fixtures and press
tools.

TEXT BOOK:
1. Joshi, P.H. “Jigs and Fixtures”, Second Edition, Tata McGraw Hill Publishing Co., Ltd.,
New Delhi, 2004.
2. Joshi P.H “Presstools - Design and Construction”, wheels publishing, 1996

REFERENCES:
1. K. Venkataraman, “Design of Jigs Fixtures & Press Tools”, Tata McGraw Hill, New Delhi,
2005.
2. Donaldson, Lecain and Goold “Tool Design”, III rd Edition Tata McGraw Hill, 2000.
3. Kempster, “Jigs and Fixture Design”, Hoddes and Stoughton – Third Edition 1974.
4. Hoffman “Jigs and Fixture Design” – Thomson Delmar Learning, Singapore, 2004.
5. ASTME Fundamentals of Tool Design Prentice Hall of India.
6. Design Data Hand Book, PSG College of Technology, Coimbatore.

ME8075 ENERGY CONSERVATION IN INDUSTRIES LTPC

3003
OBJECTIVES:
At the end of the course, the student is expected to
• understand and analyse the energy data of industries
• carryout energy accounting and balancing
• conduct energy audit and suggest methodologies for energy savings and
• utilise the available resources in optimal ways

UNIT I INTRODUCTION 8
Energy - Power – Past & Present scenario of World; National Energy consumption Data –
Environmental aspects associated with energy utilization –Energy Auditing: Need, Types,
Methodology and Barriers. Role of Energy Managers. Instruments for energy auditing.

UNIT II ELECTRICAL SYSTEMS 12

Components of EB billing – HT and LT supply, Transformers, Cable Sizing, Concept of
Capacitors, Power Factor Improvement, Harmonics, Electric Motors - Motor Efficiency
Computation, Energy Efficient Motors, Illumination – Lux, Lumens, Types of lighting, Efficacy,
LED Lighting and scope of Encon in Illumination.
98
 UNIT III THERMAL SYSTEMS 12
Stoichiometry, Boilers, Furnaces and Thermic Fluid Heaters – Efficiency computation and
encon measures. Steam:Distribution &Usage: Steam Traps, Condensate Recovery, Flash
Steam Utilization, Insulators & Refractories

UNIT IV ENERGY CONSERVATION IN MAJOR UTILITIES 8

Pumps, Fans, Blowers, Compressed Air Systems, Refrigeration and Air Conditioning Systems
– Cooling Towers – D.G. sets

UNIT V ECONOMICS 5
Energy Economics – Discount Rate, Payback Period, Internal Rate of Return, Net Present
Value, Life Cycle Costing –ESCO concept
TOTAL: 45 PERIODS
OUTCOMES:
Upon completion of this course, the students can able to analyse the energy data of industries.
 Can carryout energy accounting and balancing
 Can suggest methodologies for energy savings

TEXT BOOK:
1. Energy Manager Training Manual(4 Volumes) available at www.energymanagertraining.
com, a website administered by Bureau of Energy Efficiency (BEE), a statutory body
under Ministry of Power, Government of India.2004.

REFERENCES:
1. L.C. Witte, P.S. Schmidt, D.R. Brown, “Industrial Energy Management and Utilisation”
HemispherePubl, Washington, 1988.
2. Callaghn, P.W. “Design and Management for Energy Conservation”, Pergamon Press,
Oxford, 1981.
3. I.G.C. Dryden, “The Efficient Use of Energy” Butterworths, London, 1982
4. W.C. turner, “Energy Management Hand book” Wiley, New York, 1982.
5. W.R. Murphy and G. Mc KAY “Energy Management” Butterworths, London 1987.

ME8076 ENTREPRENEURSHIP DEVELOPMENT LTPC

3003
OBJECTIVE:
• Study of this subject provides an understanding of the scope of an entrepreneur, key
areas of development, financial assistance by the institutions, methods of taxation and
tax benefits, etc.

99
 UNIT I ENTREPRENEURSHIP 9
Entrepreneur – Types of Entrepreneurs – Difference between Entrepreneur and Intrapreneur
– Entrepreneurship in Economic Growth, Factors Affecting Entrepreneurial Growth.

UNIT II MOTIVATION 9
Major Motives Influencing an Entrepreneur – Achievement Motivation Training, self Rating,
Business Game, Thematic Apperception Test – Stress management, Entrepreneurship
Development Programs – Need, Objectives.
UNIT III BUSINESS 9
Small Enterprises – Definition, Classification – Characteristics, Ownership Structures –
Project Formulation – Steps involved in setting up a Business – identifying, selecting a Good
Business opportunity, Market Survey and Research, Techno Economic Feasibility Assessment
– Preparation of Preliminary Project Reports – Project Appraisal – Sources of Information –
Classification of Needs and Agencies.

UNIT IV FINANCING AND ACCOUNTING 9

Need – Sources of Finance, Term Loans, Capital Structure, Financial Institution, management
of working Capital, Costing, Break Even Analysis, Network Analysis Techniques of PERT/
CPM – Taxation – Income Tax, Excise Duty – Sales Tax.

UNIT V SUPPORT TO ENTREPRENEURS 9

Sickness in small Business – Concept, Magnitude, causes and consequences, Corrective
Measures – Government Policy for Small Scale Enterprises – Growth Strategies in small
industry – Expansion, Diversification, Joint Venture, Merger and Sub Contracting.
TOTAL: 45 PERIODS
OUTCOMES :
 Upon completion of the course, students will be able to gain knowledge and skills needed to
run a business successfully.

TEXT BOOKS :
1. S.S.Khanka, “Entrepreneurial Development” S.Chand & Co. Ltd. Ram Nagar New Delhi,
1999.
2. Kurahko & Hodgetts, “ Enterprenuership – Theory, process and practices”, Thomson
learning 6th edition.

REFERENCES :
1. Hisrich R D and Peters M P, “Entrepreneurship” 5th Edition Tata McGraw-Hill,
2002.
2. Mathew J Manimala,” Enterprenuership theory at cross roads: paradigms and praxis”
Dream tech, 2nd edition 2006.
3. Rabindra N. Kanungo, “Entrepreneurship and innovation”, Sage Publications, New
Delhi, 1998. 100
4. EDII “ Faulty and External Experts – A Hand Book for New Entrepreneurs Publishers:
Entrepreneurship Development”, Institute of India, Ahmadabad, 1986.

ME8077 MARKETING MANAGEMENT LTPC

3003
OBJECTIVE:
• To understand the various processes involved in Marketing and its Philosophy.
• To learn the Psychology of consumers.
• To formulate strategies for advertising, pricing and selling

UNIT I MARKETING PROCESS 9

Definition, Marketing process, dynamics, needs, wants and demands, marketing concepts,
environment, mix, types. Philosophies, selling versus marketing, organizations, industrial
versus consumer marketing, consumer goods, industrial goods, product hierarchy

UNIT II BUYING BEHAVIOUR AND MARKET SEGMENTATION 9

Cultural, demographic factors, motives, types, buying decisions, segmentation factors -
demographic -Psycho graphic and geographic segmentation, process, patterns.

101
 UNIT III PRODUCT PRICING AND MARKETING RESEARCH 9
Objectives, pricing, decisions and pricing methods, pricing management. Introduction, uses,
process of marketing research.

UNIT IV PLANNING AND STRATEGY FORMULATION 9

Components of marketing plan-strategy formulations and the marketing process,
implementations, portfolio analysis, BCG, GEC grids.

UNIT V ADVERTISING, SALES PROMOTION AND DISTRIBUTION 9

Characteristics, impact, goals, types, and sales promotions- point of purchase- unique selling
proposition. Characteristics, wholesaling, retailing, channel design, logistics, and modern
trends in retailing.
TOTAL: 45 PERIODS
OUTCOMES :
 The learning skills of Marketing will enhance the knowledge about Marketer’s Practices and
create insights on Advertising, Branding, Retailing and Marketing Research.

TEXT BOOKS:
1. Govindarajan. M, “Marketing management – concepts, cases, challenges and trends”,
Prentice hall of India, second edition 2007.
2. Philip Kolter,Koshy Jha “Marketing Management”, Pearson Education ,Indian adapted
edition.2007

REFERENCES:
1. Ramasamy and Nama kumari, “Marketing Environment: Planning, implementation and
control the Indian context”, 1990.
2. Czinkota&Kotabe, “Marketing management”, Thomson learning, Indian edition 2007
3. Adrain palmer, “ Introduction to marketing theory and practice”, Oxford university press
IE 2004.
4. Donald S. Tull and Hawkins, “Marketing Reasearch”, Prentice Hall of Inida-1997.
5. Philip Kotler and Gary Armstrong “Principles of Marketing” Prentice Hall of India, 2000.
6. Steven J.Skinner, “Marketing”, All India Publishers and Distributes Ltd. 1998.
7. Graeme Drummond and John Ensor, Introduction to marketing concepts, Elsevier,
Indian Reprint, 2002

ME8078 NEW AND RENEWABLE SOURCES OF ENERGY LTPC

3003
OBJECTIVE:
• At the end of the course, the students are expected to identify the new methodologies /
technologies for effective utilization of renewable energy sources.

UNIT I INTRODUCTION 9
World Energy Use – Reserves of Energy Resources – Environmental Aspects of Energy
110
110
 Utilisation – Renewable Energy Scenario in Tamilnadu, India and around the World - Potentials
- Achievements / Applications – Economics of renewable energy systems.

UNIT II SOLAR ENERGY 9

Solar Radiation – Measurements of Solar Radiation - Flat Plate and Concentrating Collectors
– Solar direct Thermal Applications – Solar thermal Power Generation - Fundamentals of Solar
Photo Voltaic Conversion – Solar Cells – Solar PV Power Generation – Solar PV Applications.

UNIT III WIND ENERGY 9

Wind Data and Energy Estimation – Types of Wind Energy Systems – Performance - Site
Selection – Details of Wind Turbine Generator – Safety and Environmental Aspects

UNIT IV BIO - ENERGY 9

Biomass direct combustion – Biomass gasifiers – Biogas plants – Digesters – Ethanol
production – Bio diesel – Cogeneration - Biomass Applications

UNIT V OTHER RENEWABLE ENERGY SOURCES 9

Tidal energy – Wave Energy – Open and Closed OTEC Cycles – Small Hydro-Geothermal
Energy – Hydrogen and Storage - Fuel Cell Systems – Hybrid Systems.
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to identify the new methodologies
/ technologies for effective utilization of renewable energy sources.

TEXT BOOKS:
1. G.D. Rai, Non Conventional Energy Sources, Khanna Publishers, New Delhi, 2011.
2. Twidell, J.W. & Weir, A., Renewable Energy Sources, EFN Spon Ltd., UK, 2006.

REFERENCES:
1. S.P. Sukhatme, Solar Energy, Tata McGraw Hill Publishing Company Ltd., New Delhi,
1997.
2. GodfreyBoyle,RenewableEnergy,PowerforaSustainableFuture,OxfordUniversityPress,
U.K., 1996.
3. G.N. Tiwari, Solar Energy – Fundamentals Design, Modelling& Applications, Narosa
Publishing House, New Delhi, 2002.
4. L.L. Freris, Wind Energy Conversion Systems, Prentice Hall, UK, 1990.
5. Johnson Gary, L. Wind Energy Systems, Prentice Hall, New York, 1985
6. David M. Mousdale – Introduction to Biofuels, CRC Press, Taylor & Francis Group, USA
2010
7. Chetan Singh Solanki, Solar Photovoltaics, Fundamentals, Technologies andApplications,
PHI Learning Private Limited, New Delhi 2009.

111
111
ME8079 NON-TRADITIONAL MACHINING PROCESSES LTPC
3003
OBJECTIVES:
• To understand material removal by using various forms of energy and machining new
materials and complex parts with high accuracy by using non-traditional machining.

UNIT I INTRODUCTION 7
Need of Non-Traditional Machining Processes – Classification Based on Energy, Mechanism,
source of energy, transfer media and process - Process selection-Based on Physical
Parameters, shapes to be machined, process capability and economics – Overview of all
processes.
UNIT II MECHANICAL PROCESS 10
Ultrasonic Machining: Principle- Transducer types – Concentrators - Abrasive Slurry - Process
Parameters – Tool Feed Mechanism – Advantages and Limitations – Applications. Abrasive Jet
Machining: Process- Principle – Process Variables – Material Removal Rate - Advantages and
Limitations – Applications. Water Jet Machining: Principle – Process Variables - Advantages
and Limitations – Practical Applications – Abrasive water jet machining process.

UNIT III ELECTRICAL DISCHARGE MACHINING 10

Electrical Discharge Machining: Mechanism of metal removal – Dielectric Fluid – Flushing
methods - Electrode Materials - Spark Erosion Generators – Electrode Feed System – Material
Removal Rate – Process Parameters – Tool Electrode Design – Tool wear Characteristics
of Spark Eroded Surfaces- Advantages and Limitations – Practical Applications. Electrical
Discharge Wire Cut and Grinding: Principle – Wire Feed System - Advantages and Limitations
– Practical Applications

UNIT IV CHEMICAL AND ELECTRO CHEMICAL MACHINING 10

Chemical Machining: fundamentals, Principle –classification and selection of Etchant -chemical
milling, Engraving, Blanking - Advantages and limitations – Applications. Electro Chemical
Machining: Electro-chemistry of the process-Electrolytes - Electrolyte and their Properties
– Material Removal Rate – Tool Material – Tool Feed System – Design For Electrolyte Flow –
Process Variables - Advantages and Limitations – Applications - Electro Chemical Grinding:
Honing, cutting off, Deburring and turning.

UNIT V HIGH ENERGY MACHINING PROCESS 8

Electron Beam Machining: Principle –Generation and control of electron beam-Advantages
and Limitations – Applications. Laser Beam Machining: Principle –Solid and Gas Laser
Application – Thermal Features of LBM - Advantages and Limitations – Applications. Ion
Beam Machining: Equipment – process characteristics - Advantages and Limitations –
Applications. Plasma Arc Machining: Principle –Gas mixture– Types of Torches – Process
Parameters - Advantages and Limitations – Applications. Ion Beam Machining – Principle –
MRR – advantages, limitation, applications.
112
112
 TOTAL : 45 PERIODS

OUTCOMES:
 Upon completion of this course, the students can able to demonstrate different
unconventional machining processes and know the influence of difference process
parameters on the performance and their applications.

TEXT BOOKS:
1. P.C Pandey And H.S. Shan, “Modern Machining Process”, Tata Mc Graw – Hill Publishing
Company Limited, New Delhi, 2007
2. V.K. Jain, “ Advanced Machining Process”, Allied Publishers Pvt Limited 2007

REFERENCES:
1. Amithaba Bhattacharyya , “New Technology”, The Institution Of Engineers , (India)
“Production Technology”, HMT Bangalore, Tata Mc Graw–Hill Publishing Company
Limited, New Delhi, 2006.
2. Hassan El – Hofy “Advanced machining Processes” MC Graw-Hill, 2005.

ME8080 REFRIGERATION AND AIR CONDITIONING LTPC

3003

OBJECTIVES:
• To understand the underlying principles of operations in different Refrigeration & Air
conditioning systems and components.
• To provide knowledge on design aspects of Refrigeration & Air conditioning systems

UNIT I INTRODUCTION 5
Introduction to Refrigeration - Unit of Refrigeration and C.O.P.– Ideal cycles- Refrigerants
Desirable properties – Classification - Nomenclature - ODP & GWP.

UNIT II VAPOUR COMPRESSION REFRIGERATION SYSTEM 10

Vapor compression cycle : p-h and T-s diagrams - deviations from theoretical cycle - sub-
cooling and super heating- effects of condenser and evaporator pressure on COP- multi-
pressure system - low temperature refrigeration - Cascade systems – problems. Equipments:
Type of Compressors, Condensers, Expansion devices, Evaporators.

UNIT III OTHER REFRIGERATION SYSTEMS 8

Working principles of Vapour absorption systems and adsorption cooling systems - Steam
jet refrigeration- Ejector refrigeration systems- Thermoelectric refrigeration- Air refrigeration -
Magnetic - Vortex and Pulse tube refrigeration systems.

113
113
 UNIT IV PSYCHROMETRIC PROPERTIES AND PROCESSES 10
Properties of moist Air-Gibbs Dalton law, Specific humidity, Dew point temperature, Degree
of saturation, Relative humidity, Enthalpy, Humid specific heat, Wet bulb temperature
Thermodynamic wet bulb temperature, Psychrometric chart; Psychrometric of air-conditioning
processes, mixing of air streams.
UNIT V AIR CONDITIONING SYSTEMS AND LOAD ESTIMATION 12
Air conditioning loads: Outside and inside design conditions; Heat transfer through structure,
Solar radiation, Electrical appliances, Infiltration and ventilation, internal heat load; Apparatus
selection; fresh air load, human comfort & IAQ principles, effective temperature & chart,
calculation of summer & winter air conditioning load; Classifications, Layout of plants; Air
distribution system; Filters; Air Conditioning Systems with Controls: Temperature, Pressure
and Humidity sensors, Actuators & Safety controls.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to demonstrate the operations in
different Refrigeration & Air conditioning systems and also able to design Refrigeration &
Air conditioning systems .

TEXT BOOK:
1. Arora, C.P., Refrigeration and Air Conditioning, McGraw Hill, 3rd ed, New Delhi, 2010.

REFERENCES:
1. Roy J. Dossat, Principles of Refrigeration, Pearson Education Asia, 4th ed, 2009.
2. Stoecker, W.F. and Jones J. W., Refrigeration andAir Conditioning, McGraw Hill, New Delhi,
1986.
3. ASHRAE Hand book, Fundamentals 2010
4. Jones W.P., Air conditioning engineering, Elsevier Butterworth-Heinemann, 5th ed, 2001

ME8081 RELIABILITY CONCEPTS IN ENGINEERING LTPC

3003
OBJECTIVE:
• To impart knowledge in reliability concepts, reliability estimation methods and reliability
improvement methods

UNIT I RELIABILITY CONCEPT 9

Reliability definition –Reliability parameters- f(t), F(t) and R(t) functions- Measures of central
tendency – Bath tub curve – A priori and posteriori probabilities of failure – Component
mortality - Useful life.

114
114
 UNIT II LIFE DATA ANALYSIS 9
Data classification – Non parametric methods: Ungrouped, Grouped, Complete, Censored
data – Time to failure distributions – Probability plotting: Exponential, Weibull - Goodness of
fit tests – Survival graphs.
UNIT III RELIABILITY ESTIMATION 9
Series parallel configurations – Parallel redundancy – m/n system – Complex systems: RBD
approach – Baye’s method – Minimal path and cut sets - Fault Tree analysis – Standby system.

UNIT IV RELIABILITY MANAGEMENT 8

Reliability testing: Failure terminated test – Time terminated test – Upper and lower MTBFs –
Sequential Testing – Reliability growth monitoring – Reliability allocation.

UNIT V RELIABILITY IMPROVEMENT 10

Analysis of downtime – Repair time distribution – Maintainability prediction – Measures of
maintainability – Availability definitions – System Availability – Replacement decisions –
Economic life.
TOTAL: 45 PERIODS
OUTCOMES:
• Upon successful completion of this course, the students can able to apply the concept for
reliable component production

REFERENCES:
1. An Introduction to Reliability and Maintainability Engineering, Charles E.Ebeling, TMH,
2000.
2. Roy Billington and Ronald N. Allan, Reliability Evaluation of Engineering Systems,
Springer, 2007.

ME8552 HYDRAULICS AND PNEUMATICS LTPC

3003
OBJECTIVE:
• This course will give an appreciation of the fundamental principles, design and
operation of hydraulic and pneumatic components and systems and their application in
manufacturing and mechanical systems.

UNIT I FLUID POWER PRINCIPLES AND HYDRAULIC PUMPS 9

Introduction to Fluid power- Advantages and Applications- Fluid power systems – Types of
fluids- Properties of fluids – Basics of Hydraulics – Pascal’s Law- Principles of flow – Friction
loss- Work, Power and Torque. Problems
Sources of Hydraulic power: Pumping Theory – Pump Classification- Construction, Working,
Design, Advantages, Disadvantages, Performance, Selection criterion of Linear, Rotary- Fixed
and Variable displacement pumps-Problems

115
115
 UNIT II HYDRAULIC ACTUATORS AND VALVES 9
Hydraulic Actuators: Cylinders– Types and construction, Application, Hydraulic cushioning -
Hydraulic motors Control Components: Direction control, Flow control and Pressure control
valves- Types, Construction and Operation- Servo and Proportional valves - Applications –
Types of actuation. Accessories: Reservoirs, Pressure Switches- Applications- Fluid Power
ANSI Symbols - Problems

UNIT III HYDRAULIC SYSTEMS 9

Accumulators, Intensifiers, Industrial hydraulic circuits- Regenerative, Pump Unloading,
Double-pump, Pressure Intensifier, Air-over oil, Sequence, Reciprocation, Synchronization,
Fail-safe, Speed control, Hydrostatic transmission, Electro hydraulic circuits, Mechanical
Hydraulic servo systems.

UNIT IV PNEUMATIC SYSTEMS 9

Properties of air– Perfect Gas Laws- Compressors- Filter, Regulator, Lubricator, Muffler, Air
control Valves, Quick Exhaust valves, Pneumatic actuators, Design of pneumatic circuit-
cascade method- Electro pneumatic circuits, Introduction to Fluidics, Pneumatic logic circuits.

UNIT V TROUBLE SHOOTING AND APPLICATIONS 9

Installation, Selection, Maintenance, Trouble Shooting and Remedies in Hydraulic and Pneumatic
systems. Design of hydraulic circuits for Drilling, Planning, Shaping, Surface grinding, Press and
Forklift applications. Design of Pneumatic circuits for a Pick and Place application and tool handling
in a CNC machine. - Low cost Automation – Hydraulic and Pneumatic power packs- case studies.
TOTAL: 45 PERIODS
OUTCOMES:
 Identify hydraulic and pneumatics components.
 Ability to design hydraulic and pneumatic circuits.
TEXT BOOK:
1. Anthony Esposito, “Fluid Power with Applications”, Prentice Hall, 2009.

REFERENCES:
1. Shanmugasundaram.K, “Hydraulic and Pneumatic controls”, Chand & Co, 2006.
2. Majumdar, S.R., “Oil Hydraulics Systems- Principles and Maintenance”, Tata
McGraw Hill, 2001
3. Majumdar, S.R., “Pneumatic Systems – Principles and Maintenance”, Tata McGraw
Hill, 2007.
4. Dudelyt, A Pease and John J Pippenger, “Basic Fluid Power”, Prentice Hall, 1987.
5. Srinivasan.R, “Hydraulic and Pneumatic Controls”, Vijay Nicole Imprints, 2008.
6. Joji.P, “Pneumatic Controls”, Wiley India, 2008.

116
116
 MA8356 PROBABILITY AND STATISTICS LTPC
3104
OBJECTIVES:
• To make the students acquire a sound knowledge in statistical techniques that model
engineering problems.
• The Students will have a fundamental knowledge of the concepts of probability.

UNIT I RANDOM VARIABLES 9+3

Discrete and Continuous random variables – Moments – Moment generating functions –
Binomial, Poisson, Geometric, Uniform, Exponential, Gamma, Weibull and Normal distributions
- Functions of a random variable.

UNIT II TWO-DIMENSIONAL RANDOM VARIABLES 9+3

Joint distributions – Marginal and Conditional distributions – Covariance – Correlation
and Linear regression – Transformation of random variables – Central limit theorem (for
independent and identically distributed random variables).

UNIT III TESTS OF SIGNIFICANCE 9+3

Sampling distributions - Tests for single mean, proportion, Difference of means (large and
small samples) – Tests for single variance and equality of variances – χ2-test for goodness of
fit – Independence of attributes – Non-parametric tests: Test for Randomness and Rank-sum
test (Wilcoxon test).

UNIT IV DESIGN OF EXPERIMENTS 9+3

Completely randomized design – Randomized block design – Latin square design - 22 -
factorial design - Taguchi’s robust parameter design.

UNIT V STATISTICAL QUALITY CONTROL 9+3

Control charts for measurements ( X and R charts) – Control charts for attributes (p, c and np
charts) – Tolerance limits - Acceptance sampling.
TOTAL: 60 PERIODS
OUTCOMES :
After successfully completing the course, students should be able to do the following:
 Use statistical methodology and tools in the engineering problem-solving process.
 Compute and interpret descriptive statistics using numerical and graphical techniques.
 Understand the basic concepts of probability, random variables, probability distribution, and
joint probability distribution.
 Compute point estimation of parameters, explain sampling distributions, and understand
the central limit theorem.

TEXT BOOKS:
1. Milton, J. S. and Arnold, J.C., “Introduction to Probability and Statistics”, Tata McGraw
Hill, New Delhi, 4th Edition, 3rd Reprint, 2008.
117
 2. Johnson, R.A. and Gupta, C.B., “Miller and Freund’s Probability and Statistics for
Engineers”, Pearson Education, Asia, 8th Edition, 2011.

REFERENCES:
1. Devore, J.L., “Probability and Statistics for Engineering and the Sciences”, Thomson
Brooks/Cole, International Student Edition, New Delhi, 7th Edition, 2008.
2. Walpole, R.E., Myers, R.H., Myers, S.L. and Ye, K., “Probability and Statistics for
Engineers and Scientists”, Pearson Education, Asia, 8th Edition, 2007.
3. Ross, S.M., “Introduction to Probability and Statistics for Engineers and Scientists”,
Elsevier, New Delhi, 3rd Edition, 2004.
4. Spiegel, M.R., Schiller, J. and Srinivasan, R.A., “Schaum’s Outline of Theory and
Problems of Probability and Statistics”, Tata McGraw Hill, New Delhi, 2004.

GE8751 ENGINEERING ETHICS AND HUMAN VALUES LTPC

3003
OBJECTIVES:
 To enable the students to create an awareness on Engineering Ethics and Human Values,
to instill Moral and Social Values and Loyalty and to appreciate the rights of others.

UNIT I HUMAN VALUES 10

Morals, values and Ethics – Integrity – Work ethic – Service learning – Civic virtue – Respect
for others – Living peacefully – Caring – Sharing – Honesty – Courage – Valuing time –
Cooperation – Commitment – Empathy – Self confidence – Character – Spirituality.

UNIT II ENGINEERING ETHICS 9

Senses of ‘Engineering Ethics’ – Variety of moral issues – Types of inquiry – Moral dilemmas
– Moral Autonomy – Kohlberg’s theory – Gilligan’s theory – Consensus and Controversy
– Models of professional roles - Theories about right action – Self-interest – Customs and
Religion – Uses of Ethical Theories

UNIT III ENGINEERING AS SOCIAL EXPERIMENTATION 9

Engineering as Experimentation – Engineers as responsible Experimenters – Codes of Ethics
– A Balanced Outlook on Law – The Challenger Case Study

UNIT IV SAFETY, RESPONSIBILITIES AND RIGHTS 9

Safety and Risk – Assessment of Safety and Risk – Risk Benefit Analysis and Reducing Risk
– The Three Mile Island and Chernobyl Case Studies Collegiality and Loyalty – Respect for
Authority – Collective Bargaining – Confidentiality – Conflicts of Interest – Occupational Crime
– Professional Rights – Employee Rights – Intellectual Property Rights (IPR) – Discrimination

UNIT V GLOBAL ISSUES 8

Multinational Corporations – Environmental Ethics – Computer Ethics – Weapons Development
118
 – Engineers as Managers – Consulting Engineers – Engineers as Expert Witnesses and
Advisors – Moral Leadership – Sample Code of Conduct
TOTAL : 45 PERIODS
OUTCOMES :
 Upon completion of the course, the student should be able to apply ethics in society,
discuss the ethical issues related to engineering and realize the responsibilities and rights
in the society

TEXT BOOKS
 Mike W. Martin and Roland Schinzinger, “Ethics in Engineering”, Tata McGraw Hill,
New Delhi, 2003.
 M. Govindarajan, S. Natarajan and V.S. Senthil Kumar - published by PHI revised
edition - 2012

REFERENCES:
1. Charles B. Fleddermann, “Engineering Ethics”, Pearson Prentice Hall, New Jersey, 2004.
2. Charles E. Harris, Michael S. Pritchard and Michael J. Rabins, “Engineering Ethics –
Concepts and Cases”, Thompson Wadsworth, A Division of Thomson Learning Inc.,
United States, 2000
3. John R Boatright, “Ethics and the Conduct of Business”, Pearson Education, New Delhi, 2003
4. Edmund G Seebauer and Robert L Barry, “Fundametals of Ethics for Scientists and
Engineers”, Oxford University Press, Oxford, 2001

WEB SOURCES:
1. www.onlineethics.org
2. www.nspe.org
3. www.globalethics.org
4. www.ethics.org

MG8654 TOTAL QUALITY MANAGEMENT LTPC

3003
AIM
To provide comprehensive knowledge about the principles, practices, tools and
techniques of Total quality management.

OBJECTIVES
 To understand the various principles, practices of TQM to achieve quality.
 To learn the various statistical approaches for Quality control.
 To understand the TQM tools for continuous process improvement.
 To learn the importance of ISO and Quality systems

119
UNIT I INTRODUCTION 9
Introduction - Need for quality - Evolution of quality - Definition of quality - Dimensions of
product and service quality - Basic concepts of TQM – TQM Framework - Contributions of
Quality Gurus – Barriers to TQM – Cost of Quality.

UNIT II TQM PRINCIPLES 9

Quality statements - Customer focus –Customer orientation, Customer satisfaction,
Customer complaints, Customer retention - Continuous process improvement – PDCA
cycle, 5s, Kaizen - Supplier partnership – Partnering, Supplier selection, Supplier Rating.

UNIT III TQM TOOLS & TECHNIQUES I 9

The seven traditional tools of quality – New management tools – Six-sigma: Concepts,
methodology, applications to manufacturing, service sector including IT – Bench marking –
Reason to bench mark, Bench marking process – FMEA – Stages, Types.

UNIT IV TQM TOOLS & TECHNIQUES II 9

Quality circles – Quality Function Deployment (QFD) – Taguchi quality loss function –
TPM – Concepts, improvement needs – Performance measures - BPR.

UNIT V QUALITY SYSTEMS 9

Need for ISO 9000- ISO 9000-2000 Quality System – Elements, Documentation, Quality
auditing- QS 9000 – ISO 14000 – Concepts, Requirements and Benefits –Quality Council
– Leadership, Employee involvement – Motivation, Empowerment, Team and Teamwork,
Recognition and Reward.
TOTAL : 45 PERIODS
OUTCOMES:
 The student would be able to apply the tools and techniques of quality management to
manufacturing and services processes.

TEXT BOOK:
1. Dale H.Besterfiled, et al., “Total Quality Management”, Pearson Education Asia, Third
Edition, Indian Reprint , 2006.

REFERENCE BOOKS:
1. James R. Evans and William M. Lindsay, “The Management and Control of Quality”,
(6th Edition), South-Western (Thomson Learning), 2005.
2. Oakland, J.S. “TQM – Text with Cases”, Butterworth – Heinemann Ltd., Oxford, Third
Edition , 2003.
3. Suganthi,L and Anand Samuel, “Total Quality Management”, Prentice Hall (India) Pvt.
Ltd., 2006 .
4. Janakiraman,B and Gopal, R.K, “Total Quality Management – Text and
Cases”,Prentice Hall (India) Pvt. Ltd., 2006.

120
 MF8071 ADDITIVE MANUFACTURING TECHNOLOGY LTPC
3003
OBJECTIVES:
• To know the principle methods, areas of usage, possibilities and limitations as well as
environmental effects of the Additive Manufacturing technologies
• To be familiar with the characteristics of the different materials those are used in Additive
Manufacturing.

UNIT I INTRODUCTION 10
Overview – History - Need-Classification -Additive Manufacturing Technology in product
development-Materials for Additive Manufacturing Technology – Tooling - Applications.

UNIT II CAD & REVERSE ENGINEERING 10

Basic Concept – Digitization techniques – Model Reconstruction – Data Processing for
Additive Manufacturing Technology: CAD model preparation – Part Orientation and support
generation – Model Slicing –Tool path Generation – Softwares for Additive Manufacturing
Technology: MIMICS, MAGICS.

UNIT III LIQUID BASED AND SOLID BASED ADDITIVE MANUFACTURING

SYSTEMS 10
Classification – Liquid based system – Stereolithography Apparatus (SLA)- Principle, process,
advantages and applications - Solid based system –Fused Deposition Modeling - Principle,
process, advantages and applications, Laminated Object Manufacturing.

UNIT IV POWDER BASED ADDITIVE MANUFACTURING SYSTEMS 10

Selective Laser Sintering – Principles of SLS process - Process, advantages and applications,
Three Dimensional Printing - Principle, process, advantages and applications- Laser
Engineered Net Shaping (LENS), Electron Beam Melting.

UNIT V MEDICAL AND BIO-ADDITIVE MANUFACTURING 5

Customized implants and prosthesis: Design and production. Bio-Additive Manufacturing-
Computer Aided Tissue Engineering (CATE) – Case studies
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to compare different method and
discuss the effects of the Additive Manufacturing technologies and analyse the
characteristics of the different materials in Additive Manufacturing.

TEXT BOOKS:
1. Chua C.K., Leong K.F., and Lim C.S., “Rapid prototyping: Principles and applications”,
Third edition, World Scientific Publishers, 2010.
2. Gebhardt A., “Rapid prototyping”, Hanser Gardener Publications, 2003.
121
REFERENCES:
1. Liou L.W. and Liou F.W., “Rapid Prototyping and Engineering applications : A tool box for
prototype development”, CRC Press, 2007.
2. Kamrani A.K. and Nasr E.A., “Rapid Prototyping: Theory and practice”, Springer, 2006.
3. Hilton P.D. and Jacobs P.F., “Rapid Tooling: Technologies and Industrial Applications”,
CRC press, 2000.

MF8074 INDUSTRIAL ROBOTICS LTPC

3003
OBJECTIVES:
• To understand the functions of the basic components of a Robot.
• To study the use of various types of End of Effectors and Sensors
• To impart knowledge in Robot Kinematics and Programming
• To learn Robot safety issues and economics.

UNIT I FUNDAMENTALS OF ROBOT 6

Robot - Definition - Robot Anatomy - Co ordinate Systems, Work Envelope Types and
Classification-Specifications-Pitch, Yaw, Roll, Joint Notations, Speed of Motion, Pay Load-
Robot Parts and their Functions-Need for Robots-Different Applications.

UNIT II ROBOT DRIVE SYSTEMS AND END EFFECTORS 9

Pneumatic Drives-Hydraulic Drives-Mechanical Drives-Electrical Drives-D.C. Servo Motors,
Stepper Motors, A.C. Servo Motors-Salient Features, Applications and Comparison of all these
Drives, End Effectors-Grippers-Mechanical Grippers, Pneumatic and Hydraulic- Grippers,
Magnetic Grippers, Vacuum Grippers; Two Fingered and Three Fingered Grippers; Internal
Grippers and External Grippers; Selection and Design Considerations.

UNIT III SENSORS AND MACHINE VISION 12

Requirements of a sensor, Principles and Applications of the following types of sensors-
Position sensors - Piezo Electric Sensor, LVDT, Resolvers, Optical Encoders, pneumatic
Position Sensors, Range Sensors Triangulations Principles, Structured, Lighting Approach,
Time of Flight, Range Finders, Laser Range Meters, Touch Sensors ,binary Sensors., Analog
Sensors, Wrist Sensors, Compliance Sensors, Slip Sensors, Camera, Frame Grabber,
Sensing and Digitizing Image Data-Signal Conversion, Image Storage, Lighting Techniques,
Image Processing and Analysis-Data Reduction, Segmentation, Feature Extraction, Object
Recognition, Other Algorithms, Applications-Inspection, Identification, Visual Serving and
Navigation.

122
 UNIT IV ROBOT KINEMATICS AND ROBOT PROGRAMMING 13
Forward Kinematics, Inverse Kinematics and Difference; Forward Kinematics and Reverse
Kinematics of manipulators with Two, Three Degrees of Freedom (in 2 Dimension), Four
Degrees of freedom (in 3 Dimension) Jacobians, Velocity and Forces-Manipulator Dynamics,
Trajectory Generator, Manipulator Mechanism Design-Derivations and problems. Lead through
Programming, Robot programming Languages-VAL Programming-Motion Commands, Sensor
Commands, End Effector commands and simple Programs.

UNIT V IMPLEMENTATION AND ROBOT ECONOMICS 5

RGV, AGV; Implementation of Robots in Industries-Various Steps; Safety Considerations for
Robot Operations - Economic Analysis of Robots.
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to apply the basic engineering
knowledge for the design of robotics

TEXT BOOKS:
1. KlafterR.D.,ChmielewskiT.AandNeginM.,“RoboticEngineering-AnIntegratedApproach”,
Prentice Hall, 2003.
2. Groover M.P., “Industrial Robotics-Technology Programming and Applications”, McGraw
Hill, 2001.
REFERENCE BOOKS:
1. Craig J.J., “Introduction to Robotics Mechanics and Control”, Pearson Education, 2008.
2. Deb S.R., “Robotics Technology and Flexible Automation” Tata Mc Graw Hill Book Co., 1994.
3. Koren Y., “Robotics for Engineers’, Mc Graw Hill Book Co., 1992.
4. Fu.K.S.,Gonzalz R.C. and Lee C.S.G., “Robotics Control, Sensing, Vision and Intelligence”,
McGraw Hill Book Co., 1987.
5. Janakiraman P.A., “Robotics and Image Processing”, Tata Mc Graw Hill, 1995.
6. Rajput R.K., “Robotics and Industrial Automation”, S.Chand and Company, 2008.
7. Surender Kumar, “Industrial Robots and Computer Integrated Manufacturing”, Oxford
and IBH Publishing Co. Pvt. Ltd., 1991.

MF8075 MEMS AND MICRO SYSTEM FABRICATION LTPC

3003
OBJECTIVES:
• To understand the mechanics, scaling and design of micro system
• To learn various micro fabrication processes
• To impart knowledge on microsystems packaging and metrology of micro machined
components 123
 UNIT I INTRODUCTION 9
Overview of MEMS and Microsystems: MEMS and Microsystems, Evolution of Micro fabrication,
Microsystems and Microelectronics, Microsystems and miniaturization-Materials for MEMS
and Microsystems:substrates and wafers, active substrate materials,Silicon,Galium Arsenide,
Piezoelectric Crystals, Polymers, Packaging materials-Working principles of Microsystems:
micro sensors, micro actuation, MEMS with micro actuators, Micro accelerometers, micro
fluidics-Applications of Microsystems in various industries

UNIT II MECHANICS, SCALING AND DESIGN 9

Engineering Mechanics for Microsystems design: Introduction, Static bending of Thin Plates,
Mechanical Vibration, Thermomechanics, Thermofluid Engineering and micro system design,
Laminar fluid flow, Incompressible fluid Flow, Heat conduction in solids-Scaling Laws in
Miniaturization, Introduction to scaling, Scaling in (Electrostatic forces electromagnetic forces,
Electricity, fluid mechanics, heat transfer)-Microsystems Design: Design Consideration,
Process design, Mechanical Design, Design of Micro fluidic Network systems

UNIT III MICRO SYSTEM FABRICATION PROCESSES 12

Introduction- Photolithography- Ion implantation- Chemical Vapor deposition-Physical Vapor
deposition - clean room- Bulk micromachining :etching, isotropic and anisotropic etching, wet
and dry etching- Surface micro machining :process, mechanical problems associated with
surface micro machining- LIGA process :general description, materials for substrates and
photo resists-SLIGA process-Abrasive jet micro machining-Laser beam micro machining-
Micro Electrical Discharge Micro Machining –Ultrasonic Micro Machining- Electro chemical
spark micro machining- Electron beam micro machining-Focused Ion Beam machining

UNIT IV TOOL BASED MICROMACHINING 7

Theory of tool based micromachining-Chip formation-size effect in micromachining-micro
turning, micro milling, and micro drilling- Micromachining tool design-Precision Grinding-
Partial ductile mode grinding-Ultra precision grinding- Binderless wheel Free form optics.

UNIT V MICROSYSTEMS PACKAGING AND METROLOGY OF MICRO MACHINED

COMPONENTS 8
Introduction -Microsystems Packaging-Interfaces in Microsystems Packaging-Essential
Packaging Technologies-Three dimensional Packaging- Assembly of Microsystems-
Signal Mapping and Transduction-Metrology of Micromachined components: SEM, optical
microscopy, Scanning white light interferometry, Confocal Laser scanning microscopy, SPM,
Molecular measuring machine, Micro coordinate measuring machine
TOTAL:45 PERIODS

OUTCOMES
 Ability to understand and apply basic science, circuit theory, Electro-magnetic field theory
control theory and apply them to electrical engineering problems.
 Ability to understand and analyse, linear and digital electronic circuits.
124
TEXT BOOKS:
1. Hsu T.R., “MEMS & Microsystems Design and Manufacture”, Tata McGraw Hill, 2002,
ISBN: 9780070487093.
2. Jain V.K., “Introduction to Micromachining” Narosa Publishing House, 2010.

REFERENCES:
1. Jackson M.J., “Microfabrication and Nanomanufacturing” Taylor and Francis 2006.
2. McGeough J.A., “Micromachining of Engineering Materials”, CRC Press, 2001, ISBN:
0824706447
3. Hak M.G., “MEMS Handbook”, CRC Press, 2006.
4. Madou M.F. “Fundamentals of Micro fabrication”, CRC Press, 2002, 2nd Edition.

MF8077 PRODUCT DESIGN AND DEVELOPMENT LTPC

3003
OBJECTIVE:
• To Teach the students basic concepts of Product Design and Process Development.
Expose the students to the importance, various stages, concepts, management and
prototyping of Product Design and Process Development.
UNIT I INTRODUCTION 9
Strategic importance of Product development - integration of customer, designer, material
supplier and process planner, Competitor and customer - behavior analysis. Understanding
customer-promoting customer understanding-involve customer in development and managing
requirements - Organization process management and improvement.

UNIT II CONCEPT GENERATION, SELECTION AND TESTING 9

Plan and establish product specifications. Task - Structured approaches - clarification - search-
externally and internally-Explore systematically - reflect on the solutions and processes -
concept selection - methodology - benefits. Implications - Product change - variety - component
standardization - product performance – manufacturability.

UNIT III PRODUCT ARCHITECTURE 9

Product development management - establishing the architecture - creation - clustering -
geometric layout development - Fundamental and incidental interactions - related system level
design issues - secondary systems -architecture of the chunks - creating detailed interface
specifications-Portfolio Architecture.

UNIT IV INDUSTRIAL DESIGN 9

Integrate process design - Managing costs - Robust design - Integrating CAE, CAD, CAM
tools – Simulating product performance and manufacturing processes electronically - Need for
125
 industrial design-impact – design process - investigation of customer needs - conceptualization
- refinement - management of the industrial design process.

UNIT V DESIGN FOR MANUFACTURING AND PRODUCT DEVELOPMENT 9

Definition - Estimation of Manufacturing cost-reducing the component costs and assembly
costs – Minimize system complexity - Prototype basics - Principles of prototyping - Planning
for prototypes - Economic Analysis.
TOTAL: 45 PERIODS
OUTCOME
The student would have the
 Ability to launch own ideas and the ideas of others, which enables them to manage to work
with innovation and development in large companies
 Ability to apply new theories on innovation and change, including emerging paradigms such
as user-driven innovation, open innovation and market forecasting in practice.

TEXT BOOK:
1. Ulrich K.T. and Eppinger S.D., “Product Design and Development” McGraw –Hill
International Editions,1999.

REFERENCES:
1. Belz A., 36-Hour Course: “Product Development” McGraw-Hill, 2010.
2. Rosenthal S., “Effective Product Design and Development”, Business One Orwin,
Homewood, 1992, ISBN 1-55623-603-4.
3. Pugh S., “Total Design – Integrated Methods for successful Product Engineering”,
Addison Wesley Publishing, 1991, ISBN 0-202-41639-5.

MF8451 PROCESS PLANNING AND COST ESTIMATION LTPC

3003
OBJECTIVE:
• To introduce the process planning concepts to make cost estimation for various products
after process planning

UNIT I INTRODUCTION TO PROCESS PLANNING 10

Introduction- methods of process planning-Drawing interpretation-Material evaluation – steps
in process selection-.Production equipment and tooling selection

UNIT II PROCESS PLANNING ACTIVITIES 10

Process parameters calculation for various production processes-Selection jigs and fixtures-
selection of quality assurance methods - Set of documents for process planning-Economics
of process planning- case studies
126
 UNIT III INTRODUCTION TO COST ESTIMATION 8
Importance of costing and estimation –methods of costing-elements of cost estimation –Types
of estimates – Estimating procedure- Estimation labor cost, material cost- allocation of over
head charges- Calculation of depreciation cost

UNIT IV PRODUCTION COST ESTIMATION 8

Estimation of Different Types of Jobs - Estimation of Forging Shop , Estimation of Welding
Shop, Estimation of Foundry Shop

UNIT V MACHINING TIME CALCULATION 9

Estimation of Machining Time - Importance of Machine Time Calculation- Calculation of
Machining Time for Different Lathe Operations ,Drilling and Boring - Machining Time Calculation
for Milling , Shaping and Planning -Machining Time Calculation for Grinding
TOTAL: 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to use the concepts of process
planning and cost estimation for various products.

TEXT BOOKS:
1. Peter scalon, “Process planning, Design/Manufacture interface”, Elsevier science
technology Books, Dec 2002.

REFERENCES:
1. Ostwalal P.F. and Munez J., “Manufacturing Processes and systems”, John Wiley, 9th
Edition, 1998.
2. Russell R.S and Tailor B.W, “Operations Management”, PHI, 4th Edition, 2003.
3. Chitale A.V. and Gupta R.C., “Product Design and Manufacturing”, PHI, 2nd Edition, 2002.

MF8751 OPERATIONS RESEARCH LTPC

3003
OBJECTIVE:
• To provide knowledge and training in using optimization techniques under limited
resources for the engineering and business problems.

UNIT I LINEAR MODELS 15

The phase of an operation research study – Linear programming – Graphical method– Simplex
algorithm – Duality formulation – Sensitivity analysis.

UNIT II TRANSPORTATION MODELS AND NETWORK MODELS 8

Transportation Assignment Models –Traveling Salesman problem-Networks models – Shortest
route – Minimal spanning tree – Maximum flow models –Project network – CPM and PERT
networks – Critical path scheduling – Sequencing models.
127
 UNIT III INVENTORY MODELS 6
Inventory models – Economic order quantity models – Quantity discount models – Stochastic
inventory models – Multi product models – Inventory control models in practice.

UNIT IV QUEUEING MODELS 6

Queueing models - Queueing systems and structures – Notation parameter – Single server
and multi server models – Poisson input – Exponential service – Constant rate service –
Infinite population – Simulation.

UNIT V DECISION MODELS 10

Decision models – Game theory – Two person zero sum games – Graphical solution- Algebraic
solution – Linear Programming solution – Replacement models – Models based on service life –
Economic life – Single / Multi variable search technique – Dynamic Programming – Simple
Problem.
TOTAL: 45 PERIODS
OUTCOMES:
• Upon completion of this course, the students can able to use the optimization techniques
for use engineering and Business problems

TEXT BOOK:
1. Taha H.A., “Operations Research”, Prentice Hall of India, 2003, Sixth Edition.

REFERENCE BOOKS:
1. Shennoy G.V. and Srivastava U.K., “Operation Research for Management”, Wiley
Eastern, 1994.
2. Bazara M.J., Jarvis and Sherali H., “Linear Programming and Network Flows”, John
Wiley, 1990.
3. Philip D.T. and Ravindran A., “Operations Research”, John Wiley, 1992.
4. Hillier and Libeberman, “Operations Research”, Holden Day, 1986
5. Budnick F.S., “Principles of Operations Research for Management”, Richard D Irwin,
1990.
6. Tulsian and Pasdey V., “Quantitative Techniques”, Pearson – Asia 2002.

ML8022 NONDESTRUCTIVE MATERIALS EVALUATION LTPC

3003
OBJECTIVE:
To study and understand the various Non Destructive Evaluation and Testing methods, theory
and their industrial applications.

128
 UNIT I OVERVIEW OF NDT 7
NDT Versus Mechanical testing, Overview of the Non Destructive Testing Methods for the
detection of manufacturing defects as well as material characterisation. Relative merits and
limitations, Various physical characteristics of materials and their applications in NDT., Visual
inspection – Unaided and aided.

UNIT II SURFACE NDE METHODS 8

Liquid Penetrant Testing - Principles, types and properties of liquid penetrants, developers,
advantages and limitations of various methods,Testing Procedure, Interpretation of results. Magnetic
Particle Testing- Theory of magnetism, inspection materials Magnetisation methods, Interpretation
and evaluation of test indications, Principles and methods of demagnetization, Residual magnetism.

UNIT III THERMOGRAPHY AND EDDY CURRENT TESTING (ET) 10

Thermography- Principles, Contact and non contact inspection methods, Techniques for
applying liquid crystals, Advantages and limitation - infrared radiation and infrared detectors,
Instrumentations and methods, applications.
Eddy Current Testing-Generation of eddy currents, Properties of eddy currents, Eddy current
sensing elements, Probes, Instrumentation, Types of arrangement , Applications, advantages,
Limitations, Interpretation/Evaluation.

UNIT IV ULTRASONIC TESTING (UT) AND ACOUSTIC EMISSION (AE) 10

Ultrasonic Testing-Principle, Transducers, transmission and pulse-echo method, straight beam
and angle beam, instrumentation, data representation, A/Scan, B-scan, C-scan. Phased Array
Ultrasound, Time of Flight Diffraction.
Acoustic Emission Technique –Principle, AE parameters, Applications.

UNIT V RADIOGRAPHY (RT) 10

Principle, interaction of X-Ray with matter, imaging, film and film less techniques, types
and use of filters and screens, geometric factors, Inverse square, law, characteristics of
films - graininess, density, speed, contrast, characteristic curves, Penetrameters, Exposure
charts, Radiographic equivalence. Fluoroscopy- Xero-Radiography, Computed Radiography,
Computed Tomography
TOTAL : 45 PERIODS
OUTCOMES:
 Upon completion of this course, the students can able to use the various Non Destructive
Testing and Testing methods understand for defects and characterization of industrial
components

TEXT BOOKS:
1. Baldev Raj, T.Jayakumar, M.Thavasimuthu “Practical Non-Destructive Testing”, Narosa
Publishing House, 2009.
2. Ravi Prakash, “Non-Destructive Testing Techniques”, New Age International Publishers,
1st revised edition, 2010
129
 REFERENCES:
1. ASM Metals Handbook,”Non-Destructive Evaluation and Quality Control”, American
Society of Metals, Metals Park, Ohio, USA, 200, Volume-17.
2. Paul E Mix, “Introduction to Non-destructive testing: a training guide”, Wiley, 2nd edition
New Jersey, 2005
3. Charles, J. Hellier,“ Handbook of Nondestructive evaluation”, McGraw Hill, New York 2001.
4. ASNT, American Society for Non Destructive Testing, Columbus, Ohio, NDT Handbook,
Vol. 1, Leak Testing, Vol. 2, Liquid Penetrant Testing, Vol. 3, Infrared and Thermal Testing
Vol. 4, Radiographic Testing, Vol. 5, Electromagnetic Testing, Vol. 6, Acoustic Emission
Testing, Vol. 7, Ultrasonic Testing

GE8072 DISASTER MANAGEMENT L T P C

3 0 0 3
OBJECTIVES:
 To provide students an exposure to disasters, their significance and types.
 To ensure that students begin to understand the relationship between vulnerability,
disasters, disaster prevention and risk reduction
 To gain a preliminary understanding of approaches of Disaster Risk Reduction (DRR)
 To enhance awareness of institutional processes in the country and
 To develop rudimentary ability to respond to their surroundings with potential
disaster response in areas where they live, with due sensitivity

UNIT I INTRODUCTION TO DISASTERS 9

Definition: Disaster, Hazard, Vulnerability, Resilience, Risks – Disasters: Types of disasters –
Earthquake, Landslide, Flood, Drought, Fire etc - Classification, Causes, Impacts including social,
economic, political, environmental, health, psychosocial, etc.- Differential impacts- in terms of caste,
class, gender, age, location, disability - Global trends in disasters: urban disasters, pandemics,
complex emergencies, Climate change- Dos and Don’ts during various types of Disasters.

UNIT II APPROACHES TO DISASTER RISK REDUCTION (DRR) 9

Disaster cycle - Phases, Culture of safety, prevention, mitigation and preparedness community
based DRR, Structural- nonstructural measures, Roles and responsibilities of- community,
Panchayati Raj Institutions/Urban Local Bodies (PRIs/ULBs), States, Centre, and other stake-
holders- Institutional Processess and Framework at State and Central Level- State Disaster
Management Authority(SDMA) – Early Warning System – Advisories from Appropriate Agencies.

UNIT III INTER-RELATIONSHIP BETWEEN DISASTERS AND DEVELOPMENT 9

Factors affecting Vulnerabilities, differential impacts, impact of Development projects such as dams,
embankments, changes in Land-use etc.- Climate Change Adaptation- IPCC Scenario and

130
Scenarios in the context of India - Relevance of indigenous knowledge, appropriate technology and
local resources.

UNIT IV DISASTER RISK MANAGEMENT IN INDIA 9

Hazard and Vulnerability profile of India, Components of Disaster Relief: Water, Food, Sanitation,
Shelter, Health, Waste Management, Institutional arrangements (Mitigation, Response and
Preparedness, Disaster Management Act and Policy - Other related policies, plans, programmes
and legislation – Role of GIS and Information Technology Components in Preparedness, Risk
Assessment, Response and Recovery Phases of Disaster – Disaster Damage Assessment.

UNIT V DISASTER MANAGEMENT: APPLICATIONS AND CASE STUDIES AND FIELD

WORKS 9
Landslide Hazard Zonation: Case Studies, Earthquake Vulnerability Assessment of Buildings and
Infrastructure: Case Studies, Drought Assessment: Case Studies, Coastal Flooding: Storm Surge
Assessment, Floods: Fluvial and Pluvial Flooding: Case Studies; Forest Fire: Case Studies, Man
Made disasters: Case Studies, Space Based Inputs for Disaster Mitigation and Management and
field works related to disaster management.
TOTAL: 45 PERIODS
OUTCOMES:
The students will be able to
 Differentiate the types of disasters, causes and their impact on environment and
society
 Assess vulnerability and various methods of risk reduction measures as well as
mitigation.
 Draw the hazard and vulnerability profile of India, Scenarious in the Indian context,
Disaster damage assessment and management.

TEXTBOOK:
1. Singhal J.P. “Disaster Management”, Laxmi Publications, 2010. ISBN-10: 9380386427
ISBN-13: 978-9380386423
2. Tushar Bhattacharya, “Disaster Science and Management”, McGraw Hill India Education
Pvt. Ltd., 2012. ISBN-10: 1259007367, ISBN-13: 978-1259007361]
3. Gupta Anil K, Sreeja S. Nair. Environmental Knowledge for Disaster Risk Management,
NIDM, New Delhi, 2011
4. Kapur Anu Vulnerable India: A Geographical Study of Disasters, IIAS and Sage Publishers,
New Delhi, 2010.

REFERENCES
1. Govt. of India: Disaster Management Act , Government of India, New Delhi, 2005
2. Government of India, National Disaster Management Policy,2009.

GE8073 HUMAN RIGHTS L T P C

3 0 0 3
OBJECTIVES :
 To sensitize the Engineering students to various aspects of Human Rights.
131
 UNIT I 9
Human Rights – Meaning, origin and Development. Notion and classification of Rights – Natural,
Moral and Legal Rights. Civil and Political Rights, Economic, Social and Cultural Rights; collective
/ Solidarity Rights.

UNIT II 9
Evolution of the concept of Human Rights Magana carta – Geneva convention of 1864. Universal
Declaration of Human Rights, 1948. Theories of Human Rights.

UNIT III 9
Theories and perspectives of UN Laws – UN Agencies to monitor and compliance.

UNIT IV 9
Human Rights in India – Constitutional Provisions / Guarantees.

UNIT V 9
Human Rights of Disadvantaged People – Women, Children, Displaced persons and Disabled
persons, including Aged and HIV Infected People. Implementation of Human Rights – National and
State Human Rights Commission – Judiciary – Role of NGO’s, Media, Educational Institutions,
Social Movements.
TOTAL : 45 PERIODS
OUTCOME :
 Engineering students will acquire the basic knowledge of human rights.

REFERENCES:
1. Kapoor S.K., “Human Rights under International law and Indian Laws”, Central Law Agency,
Allahabad, 2014.
2. Chandra U., “Human Rights”, Allahabad Law Agency, Allahabad, 2014.
3. Upendra Baxi, The Future of Human Rights, Oxford University Press, New Delhi.

132