Demo Only Version

This is a promotional sample of the IPC Training

and Reference Guide — DRM-18H.
Please do not use this SAMPLE for training or
reference purposes.
IPC is a not-for-profit association for the elec-
tronics industry. Please respect our copyright.
You may order printed copies from IPC at:
http://training.ipc.org or call (847) 597-2862.
Thank you for viewing this DRM-18H demo.

Association Connecting Electronics Industries

© 2007
3000 Lakeside Drive, Suite 309 S, • Bannockburn, IL 60015
Telephone: +1 847.615.7100 • FAX: +1 847.615.7105
All rights reserved under both international and Pan-American copyright
conventions. Any copying, scanning or other reproductions of these materials
without the prior written consent of the copyright holder is strictly prohibited
and constitutes infringement under the Copyright Law of the United States.
 Table of Contents
Terminology Surface Mount • CHIPs, MELFs & SOTs
Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 Chip Components . . . . . . . . . . . . . . . . . . . . . . 39
Through Hole vs. Surface Mount . . . . . . . 3 Chip Components/Resistor . . . . . . . . . . . . . . 40
Through Hole Leads . . . . . . . . . . . . . . . . 3, 4 Chip Components/Capacitor . . . . . . . . . . . . . . 41
Surface Mount Leadless . . . . . . . . . . . . . . 4 Tantalum Capacitor . . . . . . . . . . . . . . . . . . . . 42
Surface Mount Leaded . . . . . . . . . . . . . . . 5 MELF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Component Packaging . . . . . . . . . . . . . . . . 6 SOT/SOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Identifying Components . . . . . . . . . . . . . . . 7 DPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Lead-Free Components . . . . . . . . . . . . . . . . 8
Surface Mount • Dual Inline SOICs
Component Reference Designators . . . . . 9
Common Class Letters . . . . . . . . . . . . . . 10 SOIC/SOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Schematic Symbols . . . . . . . . . . . . . . . . . . 11 SO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Value and Tolerance . . . . . . . . . . . . . . . . . . 11 SOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 SOL/SOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Orientation . . . . . . . . . . . . . . . . . . . . . . . . 13 SOJ/SOL-J . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
The Square Land/Pad . . . . . . . . . . . . . . . . 13 SSOP/VSOP/TSSOP . . . . . . . . . . . . . . . . . . . . . 51
QSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Through Hole • Axial & Radial TSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Capacitor (Non-Polarized) . . . . . . . . . . . . 14 Flat Lead Small Outline and Quad Package 54
Capacitor (Polarized) . . . . . . . . . . . . . 15, 16
Surface Mount • Peripheral Leaded Quads
Variable Capacitor . . . . . . . . . . . . . . . . . . 17
Crystal Oscillator . . . . . . . . . . . . . . . . . . . 18 PLCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 QFP/MQFP/FQFP/CQFP . . . . . . . . . . . . . . . . . 56
Light-Emitting Diode . . . . . . . . . . . . . . . . 20 LQFP/TQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 PQFP BQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Fuse and Circuit Breaker . . . . . . . . . . . . . 22
Surface Mount • Peripheral Dual and Quad
Inductor and Coil . . . . . . . . . . . . . . . . . . . 23 Leadless Packages
Transformer . . . . . . . . . . . . . . . . . . . . . . . . 24
Resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 LCC/LCCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Variable Resistor . . . . . . . . . . . . . . . . . . . 26 DFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Voltage Regulator . . . . . . . . . . . . . . . . . . . 27 QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Thermistor . . . . . . . . . . . . . . . . . . . . . . . . . 28 QFN Multiple Row . . . . . . . . . . . . . . . . . . . . . . .62
Transistor . . . . . . . . . . . . . . . . . . . . . . . . . 29 Surface Mount • Area Arrays
Switch and Relay . . . . . . . . . . . . . . . . . . . 30
BGA/CBGA/PBGA/CCGA/LGA . . . . . . . . . . . 63
Through Hole • Hardware PoP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Connector . . . . . . . . . . . . . . . . . . . . . . . . . 31 CSP/FBGA/DSBGA/FLGA/DSLGA . . . 65, 66
Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Surface Mount • Chip on Board
Jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 COB/Bare Die/ Flip Chip . . . . . . . . . . . . . 67, 68

Through Hole • ICs Reading Component Values

SIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Axial Resistor Values . . . . . . . . . . . . . . . . . . . 69

DIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Numbered Resistors . . . . . . . . . . . . . . . . . . . 69
IC Can . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 4-, 5-, and 6-Band Resistors . . . . . . . . . . . 70
PGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Resistor Band Color Codes . . . . . . . . . . . . . . . 71
Capacitor Values . . . . . . . . . . . . . . . . . . . . . . . 72
Numbered Capacitors . . . . . . . . . . . . . . . . . . 72
Inductor Band Color Codes . . . . . . . . . . . . . . 73

Component ID Training & Reference Guide

 Terminology Terminology

Introduction Through Hole vs. Surface Mount

There are two primary types of components, the difference being
Components how they are attached
An electronic component is any device that handles electricity. These to the circuit board.
devices come in many different configurations, shapes and sizes. Different primary
components have different electrical functions and are used for a great side One group is called
variety of purposes. For example, some components may be used to slow through hole.
electricity, and others may be used to store it. Through hole components
have leads that are inserted
Understanding Electricity secondary side through mounting holes in
Electricity basically consists of voltage, measured in volts, and current, the circuit board.
measured in amperes, or amps. Voltage is the electrical pressure, or force cross-section of a
through hole solder joint
of electricity through a circuit. This is similar to the water pressure in a
garden hose. Current is the amount of electricity that goes through the
circuit. The other type is called
Active vs. Passive surface mount.
Some components are active — meaning they can amplify or interpret Surface mount components are
a signal. Active components include diodes, transistors and integrated designed so they are placed
circuits, also called ICs. Other components are passive — meaning that directly onto lands that serve
cross-section of a
they cannot change an electrical signal — except to reduce it in size or as mounting points on the surface mount solder joint
delay it. Passive components include resistors, capacitors and inductors. surface of the board.
Discrete vs. Integrated
When a component is packaged with only one or two functional elements, Through Hole Leads
it is called a discrete component. An example of a discrete component
is a resistor that performs the simple function of limiting the electrical Axial Leads = Arms
current that flows through it. On the other hand, an integrated circuit is
Axial leaded components have two
a group of interconnected elements assembled into a single package that
leads — with one lead extending from
performs multiple functions. A well-known example of a complex IC is the
each side of the component, like arms.
microprocessor found in computers.
Axial components need to have their
Electronic Assemblies leads bent so they can be inserted
through the holes of a circuit board.
When a group of components are placed together on a printed circuit board
to perform some function, it’s called an electronic assembly. Circuit board
assemblies are created by attaching and soldering the components by Radial Leads = Legs
hand, or by machine.
Radial leaded components have two or more
leads extending from the bottom of the
component, like legs.

2 Component ID Training & Reference Guide Component ID Training & Reference Guide 3
Terminology Terminology

Single In-line Packages

or SIPs, are through hole components that Surface Mount — Leaded
have a row of leads in a single, straight line.
Leaded surface mount components usually have one of the following lead
Dual In-line Packages styles: gull wings, J-leads, L-leads, flat leads or I-leads.
or DIPs, are components that have two
Gull Wing Lead: The gull wing
rows of leads in parallel straight lines.
lead is a metal lead that bends
down and away — similar to a
seagull’s wing.

Pin Grid Arrays J-Lead: The J-lead is a metal

or PGAs, are ICs that have several lead that bends down and
rows of round pins extending from underneath a component in the
the bottom of the component. shape of the letter J.

L-Lead: The L-lead is inward

Surface Mount — Leadless formed underneath a component.

Leadless means there are no metal leads sticking out of the component Flat Lead: The flat lead
body. These types of components are attached to a circuit board using protrudes directly out from the
some type of metallized termination. body of a component.

I-Lead: The I-lead, or butt lead,

is actually a through hole lead
that has been cut short for
surface mounting. Because the
connection is not very strong
or stable, the I-lead is not
This QFN has terminals. considered suitable for high
reliability assemblies.

Chips & MELFs use terminations on opposite ends

of the component’s body.
Lead Pitch
Castellations are half round An important characteristic of some
Ball Grid Arrays, or BGAs, metallized recesses in the side of leaded surface mount components
consist of rows of tiny balls of solder a component that are filled with is lead pitch. Pitch is the distance
on the bottom of the solder when connected to the between the center or one lead
component. These solder circuit board. Lead Pitch
to the center of the next. When a
balls are connected to component has fine pitch it means
matching rows of lands the leads are spaced very close
on the circuit board. together (less than 25 mils).

4 Component ID Training & Reference Guide Component ID Training & Reference Guide 5
 Terminology Terminology

Component Packaging Identifying Components

Component packaging refers to the way component manufacturers package
their product for use by electronics assemblers. See Introduction to
Electronics Assembly, IPC-DRM-53, for more about the assembly process.
Through hole and surface mount components are packaged in one of four
ways: on tape and reel, in tubes, in waffle trays or in static-safe bags. Every component has
The packaging method depends on the component type and whether the a manufacturer’s part
component will be assembled onto the circuit board by machine or by hand. number. This number is
most component packages are made to protect the components from either marked on the
electrostatic discharge, or ESD, which could damage them. component itself, or on the
packaging.
Tape and Reel
Tape reels are used for axial leaded through hole components
and the smaller surface mount components. Automatic
insertion machines cut through hole components off tape
reels and insert them into the board. Surface mount assembly
machines, called “pick and place”, pick surface mount And every assembly to be
components from tape reels and place them onto the board. manufactured comes with an
assembly drawing and a parts list,
Tubes
Tubes are used to keep also called the bill of materials, or
components straight and ready BOM.
to drop into auto-insertion or The BOM lists the components
auto-placement machines. by part numbers, quantities and
Waffle Trays reference designators.
Waffle trays are used for many of the
larger surface mount components. They are The bill of materials
stackable on pick and place machines. Trays
also provide protection for fragile leads
during storage and handling. The assembly drawing shows the
location of each component.

Static-Safe Bags
Some components are simply
packaged loose in static-safe bags.
These components are usually simple
through hole axial and radial devices
that are too large or unusually shaped
to be inserted by machine. The assembly drawing with diode highlighted PCB reference designator for a diode

6 Component ID Training & Reference Guide Component ID Training & Reference Guide 7
 Terminology Terminology

Lead-Free Components Component Reference Designators

With the industry transitioning Most of the PCBs made

to lead-free soldering today have a component
processes, components legend silkscreened onto
will have either tin-lead them.
or lead-free terminations
and leads. It is very Close-up of a component legend printed on a through hole PCB
important to know
whether a component is These letters and numbers identify the component to be placed in the
lead free. holes or onto the lands next to each designation.

When tin-lead components are used on lead-free assemblies, there will be

cross contamination. Cross contamination may create unreliable solder Also called the silkscreen or Component
connections. There have been studies that show that contaminated solder Reference Designator (CRD), this legend
joints can develop cracks and other types of physical instabilities. But is placed on the component mounting
the biggest problem with mixing tin-lead and lead-free alloys is that it will (primary) side of the PCB. The other
make our electronic assemblies and electronic products non-compliant with side of a through hole board, like the one
European Union standards. Companies that are found non-compliant will shown, is often referred to as the solder
not have their products accepted. (secondary) side.
Lead-free components may be marked with the words “lead-free”, or with
the lead-free symbol. When there are no markings, the packaging and
accompanying documentation should be checked to verify that a component The silkscreen may also indicate the
is lead free, or RoHS compliant. direction (for orientation or polarity)
the component is to be placed on the board.
SMT boards may have the silkscreen on
both sides of the board, if it has
components on both sides.

Capacitor
CRD

For more definitions of reference

designators, see
ANSI Y32.16/ IEEE Std 200.

For more definitions of

component class letters, see
ANSI Y32.2/ IEEE Std 315, Class Letter(s) Unit Number
section 22.

8 Component ID Training & Reference Guide Component ID Training & Reference Guide 9
 Terminology Terminology

Common Class Letters for CRDs Schematic Symbols

Along with the assembly drawing and
ANSI/IEEE IEC Other
BOM, schematic diagrams are also
Amplifier AR A used to specify assemblies.
Capacitor C
Each discrete component has an
pack or network C CP or U
associated symbol that is specified
polarized C “+” (by the lead)
variable C C VAR, C ADJ in IEEE (Institute of Electrical and
Connector J or P Electronics Engineers) Standard
Crystal Y B 315 and 315A (ANSI Y32.2).
Delay Line DL D --- Components with multiple functions,
Diode D or CR V such as an integrated circuit, do not
Light Emitting Diode DS (Display) E LED, D, DIS, CR use a specific schematic symbol but
Voltage Rectifier D or CR V VR are often represented by a block in
Zener Diode D or VR V the schematic diagram. This includes
Filter FL Z ICs packaged as DIPs, SOICs, QFPs,
Fuse F PLCCs, PGAs or BGAs.
Header J or P
Inductor, Choke L
Integrated Circuit U IC Value and Tolerance
Insulated Jumper W or P JP
Jumper W, P or R JMP, J Some components will have a value and tolerance associated with them.
Microprocessor U IC, MC, CPU The value is a numerical quantity given to the component. This value is
Oscillator Y (crystal) or G (other) G OS usually assigned a tolerance which is the amount of variation allowed from
Relay K that value.
Resistor R
pack or network R RN, RP, U If a 500 ohm resistor has a
Potentiometer R VR, POT 1% tolerance, its acceptable
Thermistor RT R measurement range would be
variable R VR, VAR, VRN, ADJ 495 to 505 ohms.
Varistor R, VAR
asymmetrical D or CR But, if the same 500 ohm
symmetrical RV resistor has a 10% tolerance, its
Socket X. XAR, XU, XQ, etc. TS, S acceptable measurement range
Switch S SW would be 450 to 550 ohms.
Test Point or Pin TP TST or J
Transistor Q V U
Transformer T X, TR Reading component values and
tolerances is described in detail in
Voltage Regulator VR U the last section of this manual.

10 Component ID Training & Reference Guide Component ID Training & Reference Guide 11
Terminology Terminology

Polarity = Positive & Negative Orientation = Position

Each component placed on a PCB or “board” has a specific function. Some Component orientation refers to situations when a component must
components have a positive and negative connection to the board and so be installed on the PCB a certain way, whether or not it has polarity.
must be placed on the board in the correct orientation. This means that Orientation marks or symbols on a component’s body include:
the correct lead — positive or negative — is in the correct hole, or on the a notch, a dimple, a wedge, a stripe, or numbers.
correct land with surface mount components.
Components with this positive
and negative connection are
Polarized Capacitors said to have polarity.
Anode Cathode Anode & Cathode
+ – The positive lead is called the With multi-pin components, such as ICs, these orientation symbols indicate
anode. where “pin one” of that component is located so that pin may be mated with the
corresponding pad or land on the PCB. Many ICs have tens to hundreds of I/O
The negative lead is called the
(input/output) connection points. These may be pins, leads or terminations.
cathode.
Also, matching orientation marks may be found on the PCB. These often include
Polarity can be indicated on silkscreened symbols identical to markings on the component body (notch, dimple,
parts in a variety of ways. wedge, etc.) and/or a square pad or land on the board, especially for multi-pinned
components.
The symbol for a positive lead
is the plus sign (+), although
many components will not have The Square Land / Pad
this marking.
The square land/pad is a common way to designate polarity or orientation. The
The symbol for the negative
square land is most often used by PCB designers to show where the marked lead
lead is the minus sign (–).
+ – Markings and symbols for
or pin one of a multi-pinned component should be placed. Matching pin one of the
component to the correct land or pad on the PCB is critical for the proper function
Diodes
either the anode or cathode of the component.
leads can take many shapes For components that have the positive or anode lead
and forms. Markings on the marked, like polarized capacitors, the square land
PCB include a square land or typically indicates where the positive lead should be
pad, a “+” symbol, or a diode placed. For components which have the negative or
symbol silkscreened to the cathode lead marked, such as diodes or LEDs, the
board to show the correct square land indicates where the marked (negative)
orientation. lead should be placed.

Note: Always verify the polarity against any

drawings, schematics, silkscreen markings (or
any other documentation from your board and
component suppliers) as this may vary. Square land/pad shows
pin one orientation

12 Component ID Training & Reference Guide Component ID Training & Reference Guide 13
 Through Hole • Axial & Radial Through Hole • Axial & Radial

Capacitor (Non-Polarized) Capacitor (Polarized)

Description: Capacitors store and discharge electricity. They consist Description: Polarized capacitors function in the same way as non-
of two metal plates, or conducting surfaces, separated by polarized capacitors (see page 13).
a insulating material called a dielectric. After a sufficient Class Letter: C
buildup in one plate, the charge is felt in the opposite plate.
Other: “+” (by the lead)
There are four basic types of non-polarized capacitors:
• Ceramic disc-radial Prefix: None
• Dipped mica-radial Value Code: Measured in microfarads (µF), nanofarads (nF) orpicofarads
(pF). The value is printed on the capacitor body using some
• Mylar-radial, usually round or oval bodies
form of abbreviation. Also specified is the operating voltage
• Glass-packed axial, easy to mistake for diode or resistor. for the capacitor. These two values determine the physical
Class Letter: C (non-polarized) size of the component.
Prefix: None Tolerance: Printed as percentage (example: ±5%) or as letter scheme.
Value Code: Measured in microfarads (µF), nanofarads (nF) or picofarads Orientation: By polarity. A Square land on the PCB may mark where the
(pF). The value is printed on the capacitor body using some positive lead (anode) is to be inserted.
form of abbreviation. Also specified is the operating voltage
for the capacitor. These two values determine the physical Polarity: Polarized capacitors can be both axial or radial and will have
size of the component. one lead marked as postive (+). This positive lead can be
marked or formed in several ways:
Tolerance: Printed as percentage (example: ±5%) or as letter scheme.
Symbols:
Orientation: None Plus (+); marks positive lead
Dot (•); marks positive lead
Band; marks positive lead
Line; the line can have pluses (+) leading to the positive
leg or minuses (–) leading to the negative leg.
Arrows; arrows down the side lead to the negative end.
Continued on the next page

14 Component ID Training & Reference Guide Component ID Training & Reference Guide 15
 Through Hole • Axial & Radial Through Hole • Axial & Radial

Capacitor (Polarized) Variable Capacitor

Continued:
Description: These capacitors can change capacitance by turning a screw
Colors: that causes the plates to move closer or farther apart. The
Silver square; marks positive lead closer the plates, the higher the capacitance.
Colored end; marks positive lead Class Letter: C
Shapes and forms: Other: C VAR, C ADJ
Ridge or bevel; marks positive lead Prefix: None
Groove; marks positive lead
Bubble; marks positive lead Value Code: Measured as a range, such as 27-200 µF.
(if both ends have a bubble, the larger Tolerance: None
one is positive) Aluminum electrolytic capacitors Orientation: Non-symmetrical lead pattern allows it to be installed only
Larger lead; the PCB holes are sized one way.
to match the larger lead. Polarity: None

Another type of polarized capacitor is

the aluminum electrolytic capacitor.
These capacitors have a larger
capacitance per unit volume than
other types, making them valuable
in relatively high-current and low-
frequency electrical circuits — such
as power supply filters. The dielectric
is a thin layer of aluminum oxide.

16 Component ID Training & Reference Guide Component ID Training & Reference Guide 17
 Through Hole • Axial & Radial Through Hole • Axial & Radial

Crystal Oscillator Diode

Description: Crystal Oscillators usually have metal bodies and produce a Description: Diodes are semiconductors that only allow current to flow
consistent electrical pulse. They are typically used as clocks, in one direction — like a one way street. They can convert
controlling the timing of events in digital circuits. alternating current to direct current. A zener diode acts as
Class Letter: Y a voltage limiter for DC voltages. A diode’s part number is
Other: B usually specified by the prefix 1N, followed by two to four digit
numbers. Examples include 1N53, 1N751 and 1N4148.
Prefix: None
Class Letter: D or CR
Value Code: Measured in megahertz (MHz), or kilohertz (kHz).
Other: V
Tolerance: None
Prefix: 1N
Orientation: Angled corner or dot
Value Code: None
Polarity: None
Orientation: By polarity.
Polarity: Polarity is usually indicated by colored ring or up to three rings
near the negative (cathode) end of axial diodes. An arrow
may also point to the negative end. The PCB is marked with a
stripe, line, or arrow symbol showing where the cathode end of
the diode should be placed.
A Square Land* may also mark where the cathode end is
inserted.

* See page 13, “The Square Land/Pad”

18 Component ID Training & Reference Guide Component ID Training & Reference Guide 19
 Through Hole • Axial & Radial Through Hole • Axial & Radial

Light-Emitting Diode Filter

Also known as LEDs, these components emit light.

Description: Description: Filters are used to pass one frequency or frequency band
DS
Class Letter: while blocking others. They are often used to filter electrical
E, LED, D, DIS, CR
Other: noise in a circuit.
None Prefix: Class Letter: FL
Value Code:
None Other: Z
Tolerance:
None Prefix: None
Orientation:
By polarity. Value Code: None
LEDs are typically radial leaded, and polarity is indicated
Polarity: Tolerance: None
by a short lead, a flat side to the component housing, or Orientation: The installation of filters is usually by lead configuration.
position of the cup and spoon. The pattern of holes or lands on the PCB means there is
The cathode is usually identified by the shorter only one way to insert the filter.
lead, or by a flat side (if any) to the LED housing. Polarity: None
The cup inside the lens is sometimes associated
with the cathode lead, and the spoon with the
anode, but this may vary with some
manufacturers.
Cup

Square Land:
The PCB may also be marked with a square land Spoon
showing where the cathode end is inserted and/or
a silkscreened outline of the component body with Cathode
a flat edge to indicate polarity. Lead

See page 13, “The Square Land/Pad”

20 Component ID Training & Reference Guide Component ID Training & Reference Guide 21
 Through Hole • Axial & Radial Through Hole • Axial & Radial

Fuse / Circuit Breaker Inductor / Coil

Description: Fuses consist of a wire with low melting point metal. When Description: Inductors consist of a coil of wire that creates a magnetic
current passing through the wire exceeds a prescribed level, field when current flows through the coil.
the wire melts and opens the circuit, protecting equipment Transformers, Coils and Toroids are related to inductors (see
from damage. Transformers). The toroid choke consists of a coil wound
Class Letter: F on a toroid, or doughnut of magnetic metal. The metal core
Prefix: None increases the inductance of the coil.
Value Code: Measured in amps Class Letter: L
Tolerance: None Prefix: None
Orientation: None Value Code: Measured in microhenry (µH) or millihenry (mH). The value is
either printed on the inductor body or calculated by decoding
Polarity: None
4 of 5 colored bands on the inductor body into numbers.
A circuit breaker is a device that when exposed to excess Tolerance: Printed as last of five-band color band system.
current will “trip” or become electrically open and can be Orientation: None
reset.
Class Letter: CB

A Circuit Breaker Panel

like the one in your home.
Choke Coil

22 Component ID Training & Reference Guide Component ID Training & Reference Guide 23
Through Hole • Axial & Radial Through Hole • Axial & Radial

Transformer Resistor

Description: Transformers are related to inductors. Transformers basically Description: Resistors limit the flow of electrical current in a circuit. This
consist of primary and secondary coils wound on a common is like a highway narrowing from six lanes to a two-lane road.
core of ferromagnetic material. Fixed resistors are usually made of metal film. The bigger the
When alternating current flows through the primary coil, the metal film resistor, the greater its wattage rating (wattage is
resulting magnetic field induces an alternating voltage across a measure of electrical power). Resistors can also be made of
the secondary coil. The induced voltage can cause current to hot molded carbon.
flow in an external circuit. In addition, there are wire wound power resistors.
Class Letter: T Class Letter: R
Prefix: None Prefix: RC = color coded
Value Code: Measured in microhenry (µH) or millihenry (mH). RN = metal film
The value is printed on the body. RCL = wire wound
Orientation: Many transformers have non-symmetrical leads which only Value Code: Measured in ohms (Ω). The value is either printed on the
allow it to be installed one way. resistor body or is calculated by decoding 3 to 5 colored
bands on the resistor body into numbers.
Tolerance: Printed on body or as part of color band system.
Orientation: None
Polarity: None

Transformer mounted
on a board

24 Component ID Training & Reference Guide Component ID Training & Reference Guide 25
 Through Hole • Axial & Radial Through Hole • Axial & Radial

Variable Resistor Voltage Regulator

Description: Also called a potentiometer, trimpot or trimmer, a variable Description: Voltage regulators keep output voltage constant during
resistor is a resistor whose value can be changed by turning variations of the output load or the input voltage.
a shaft, screw or sliding a contact. The package configuration often looks like a TO-220.
Class Letter: R Class Letter: VR
Other: VR, VAR, VRN, ADJ Other: U
Prefix: None Prefix: None
Value Code: Measured in a range in ohms. Maximum value is usually Value Code: None
molded into component body. Example: 20 MΩ. Tolerance: None
Tolerance: None Orientation: Angle on the body or indented dot.
Orientation: Non-symmetrical lead pattern only allows it to be installed Polarity: None
one way. Pin one is usually identified.
A square land may also mark where pin one is inserted.*
Polarity: None

* See page 13, “The Square Land/Pad”

26 Component ID Training & Reference Guide Component ID Training & Reference Guide 27
 Through Hole • Axial & Radial Through Hole • Axial & Radial

Thermistor Transistor

Description: Resists current flow based on temperature. Description: Transistors are semiconductors that can amplify, oscillate
Often looks like a disc capacitor. and provide switching action on electrical signals. Like diodes,
Class Letter: RT transistors do not utilize units of measurement. Instead,
Other: R
their component type is usually specified by the prefix 2N or
3N, followed by two to four digit numbers. Examples include
Prefix: None 2N50, 2N701 and 2N2222A.
Value Code: None Class Letter: Q
Tolerance: None Other: V or U
Orientation: None Prefix: 2N
Polarity : None Orientation: Indicated by one of several methods:
• Pin Numbers or pin names which match to the PCB
silkscreen.
• Tab on the transistor “can”. When looking down on
the component from the top, pin one is either to the
right of, or directly underneath the tab. The pins count
counterclockwise from pin one.
• Matching component shape with PCB
silkscreen outline: Outline on PCB includes
the tab — align the tab. Outline on PCB
includes the flat side of the transistor —
align the flat side. Pattern of through holes
on PCB means there is only one way to insert
the transistor.

28 Component ID Training & Reference Guide Component ID Training & Reference Guide 29
 Through Hole • Axial & Radial Through Hole • Hardware

Switch / Relay Connector

Description: Switches open and close a circuit. Description: Connectors are placed on a PCB so that wires, cables and
Class Letter: S other outside connections can be made to the PCB. They
Other: SW usually have a housing around their pins.
Prefix: None Class Letter: P for MALE PLUG connector, or J for FEMALE
JACK / RECEPTACLE connector.
Value Code: May have value rating for maximum current in amps. Example:
10 A. May also have mechanical information such as DPDT; Orientation: Bevel, notch or pin number molded into the package.
“double-pole, double-throw” printed on it. Polarity: None
Tolerance: None
Orientation: Dot or notch
Polarity: None

Description: Relays are switches that open and close when actuated by an
applied signal.
Class Letter: K

Relay, DPDT Relay, SPDT

Relay, DPST Relay, SPST

A Relay on a partially assembled PCB

30 Component ID Training & Reference Guide Component ID Training & Reference Guide 31
 Through Hole • Hardware Through Hole • Hardware

Header Jumper

Description: Headers, like connectors are placed on a PCB so that outside Description: Also called jumper configuration, jumper wire or head pin
connections can be made. Headers usually do not have a configuration. Jumpers connect two pins on the assembly
housing around their pins. together, providing an electrical path between those points.
Class Letter: J or P Jumpers are sometimes used to solve circuitry errors in
Orientation: Usually none. Often has alignment or locking tabs for the the PCB itself. Other times they are used to provide a
connector which mates with it. Correct orientation of this tab way to change the assembly’s configuration for different
is important. applications.
Polarity: None Class Letter: W, or E for insulated piece of conductor (wire);
or P, for a plug.
Other: JP
Prefix: None
Value Code: None
Tolerance: None
Orientation: Jumper goes into header socket
Polarity: None

32 Component ID Training & Reference Guide Component ID Training & Reference Guide 33
 Through Hole • Hardware Through Hole • IC’s
resister pack
SIP

PSIP

diode array

Socket SIP

Description: Sockets are soldered onto circuit boards so that an IC can Description: SIP stands for Single-In-line-Package. SIPs are often
be plugged into the socket and not soldered directly to the resistor networks (or packs) diode arrays, power
board. This makes removing or upgrading the part much easier. converters and power regulators. PSIP stands for a Plastic
Sockets are sometimes used for components that cannot be SIP.
soldered in place because of heat sensitivity. Class Letter: R for resistor networks, D or CR for diode array, etc
Class Letter: X, XAR, XU, XQ, etc. Other: RP, RN
Other: TS, S Prefix: None
Prefix: None Value Code: SIP packages sometimes include banks of passive
Value Code: None components. Those values may be marked on the
Tolerance: None component package. For example, eight 2K resistors would
Orientation: Sockets usually have have the value: “8x2K.”
a dot Tolerance: None
or a notch Orientation: Determined by the location of lead one. A SIP IC’s leads are
to indicate orientation numbered to ensure proper placement of the component
to the PCB. Once on the circuit board or into a PCB-mounted socket. The
installed, a socket orientation marking on most SIPs is usually right over lead
may cover the PCB one. The remaining leads are counted from lead one.
orientation mark, so it’s
important to place Lead One Markings: The most common markings for
the socket correctly. orientation on SIPs are numbers, a stripe or a dot.

34 Component ID Training & Reference Guide Component ID Training & Reference Guide 35