51135

System Sensor
3825 Ohio Avenue

St. Charles, IL 60174
1-800-SENSOR2
Fax: 630-377-6495
PDRP1002.CD
The PDRP-1002/PDRP-1002E
Agent Release Control System
Manual
Document 51135
I56-1358-00
03/11/99 Revision: A
PN 51135:A ECN 99-017
Installation Precautions – Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be connected to the Like all solid state electronic devices, this system may operate
fire alarm control panel. Disconnect all sources of power before erratically or can be damaged when subjected to lightning induced
servicing. Control unit and associated equipment may be damaged by transients. Although no system is completely immune from lightning
removing and/or inserting cards, modules, or interconnecting cables transients and interferences, proper grounding will reduce
while the unit is energized. Do not attempt to install, service, or operate susceptibility. Overhead or outside aerial wiring is not recommended
this unit until this manual is read and understood. due to an increased susceptibility to nearby lightning strikes. Consu
with the Technical Services Department if any problems are
CAUTION - System Reacceptance Test after Software Changes: To anticipated or encountered.
ensure proper system operation, this product must be tested in
accordance with NFPA 72-1993 Chapter 7 after any programming Disconnect AC power and batteries prior to removing or inserting
operation or change in site-specific software. Reacceptance testing is circuit boards. Failure to do so can damage circuits.
required after any change, addition or deletion of system components, or
after any modification, repair or adjustment to system hardware or Remove all electronic assemblies prior to any drilling, filing, reamin
wiring. or punching of the enclosure. When possible, make all cable entries
from the sides or rear. Before making modifications, verify that they
All components, circuits, system operations or software functions known will not interfere with battery, transformer and printed circuit board
to be affected by a change must be 100% tested. In addition, to ensure location.
that other operations are not inadvertently affected, at least 10% of
initiating devices that are not directly affected by the change, up to a Do not tighten screw terminals more than 9 in-lbs. Over tightenin
maximum of 50 devices must also be tested and proper system may damage threads, resulting in reduced terminal contact pressure
operation verified. and difficulty with screw terminal removal.
This system contains static-sensitive components Always ground
This system meets NFPA requirements for operation at 0-49O C/ yourself with a proper wrist strap before handling any circuits so that
32-120O F and at a relative humidity of 85% RH (non-condensing) at static charges are removed from the body. Use static suppressive
30O C/86O F. However, the useful life of the system's standby batteries packaging to protect electronic assemblies removed from the unit.
and the electronic components may be adversely affected by extreme Follow the instructions in the installation, operating and
temperature ranges and humidity. Therefore, it is recommended that this programming manuals. These instructions must be followed to avoid
system and its peripherals be installed in an environment with a nominal damage to the control panel and associated equipment. FACP
room temperature of 15-27O C/60-80O F. operation and reliability depend upon proper installation.
Verify that wire sizes are adequate for all initiating device loops. Most
devices cannot tolerate more than a 10% I.R. drop from the specified
device voltage.
Fire Alarm System Limitations While installing a fire alarm system may make lower insurance
rates possible, it is not a substitute for fire insurance!
An automatic fire alarm system - typically made up of smoke Audible warning devices such as bells may not alert people if thes
detectors, heat detectors, manual pull stations, audible warning devices devices are located on the other side of closed or partly open doors o
and a fire alarm control with remote notification capability can provide are located on another floor of a building.
early warning of a developing fire. Such a system, however, does not
assure protection against property damage or loss of life resulting from a A fire alarm system will not operate without any electrical power. I
fire. AC power fails, the system will operate from standby batteries only fo
a specified time.
Any fire alarm system may fail for a variety of reasons:
Rate-of-Rise heat detectors may be subject to reduced sensitivity
Smoke detectors may not sense fire where smoke cannot reach the over time. For this reason, the rate-of-rise feature of each detector
detectors such as in chimneys, in walls, or roofs, or on the other side of should be tested at least once per year by a qualified fire protection
closed doors. Smoke detectors also may not sense a fire on another specialist.
level or floor of a building. A second floor detector, for example, may not
sense a first floor or basement fire. Furthermore, all types of smoke Equipment used in the system may not be technically compatible
detectors - both ionization and photoelectric types, have sensing with the control panel. It is essential to use only equipment listed fo
limitations. No type of smoke detector can sense every kind of fire service with your control panel.
caused by carelessness and safety hazards like smoking in bed, violent Telephone lines needed to transmit alarm signals from a premise to
explosions, escaping gas, improper storage of flammable materials, central monitoring station may be out of service or temporarily
overloaded electrical circuits, children playing with matches, or arson. disabled.
IMPORTANT! Smoke detectors must be installed in the same room as The most common cause of fire alarm malfunctions, however, is
the control panel and in rooms used by the system for the connection of inadequate maintenance. All devices and system wiring should be
alarm transmission wiring, communications, signaling and /or power. If tested and maintained by professional fire alarm installers following
detectors are not so located, a developing fire may damage the alarm written procedures supplied with each device. System inspection an
system, crippling its ability to report a fire. testing should be scheduled monthly or as required by National and/o
local fire codes. Adequate written records of all inspections should b
kept.
FCC Warning
WARNING: This equipment generates, uses and can radiate radio Canadian Requirements
frequency energy and if not installed and used in accordance with the This digital apparatus does not exceed the Class A limits for radiatio
instruction manual, may cause interference to radio communications, It noise emissions from digital apparatus set out in the Radio
has been tested and found to comply with the limits for class A Interference Regulations of the Canadian Department of
computing device pursuant to Subpart B of 15 of FCC Rules, which is Communications.
designed to provide reasonable protection against such interference
when operated in a commercial environment. Operation of this Le present appareil numerique n'emet pas de bruits radioelectriques
equipment in a residential area is likely to cause interference, in which depassant les limites applicables aux appareils numeriques de la
case the user will be required to correct the interference at his own classe A prescrites dans le Reglement sur le brouillage
expense. radioelectrique edicte par le ministere des Communications du
Canada.
2 The PDRP-1002 PN 51135:A 03/11/99

The PDRP-1002 PN 51135:A 03/11/99 3
4 The PDRP-1002 PN 51135:A 03/11/99
NFPA Standards
This control panel complies with the following NFPA standards:
NFPA 12 CO2 Extinguishing Systems (High Pressure Only)
NFPA 12A Halon 1301 Extinguishing Systems
NFPA 12B Halon 1211 Extinguishing Systems
NFPA 72 Central Station Signaling Systems (Automatic, Manual, and Waterflow). Protected
Premises Unit (Requires NOTI•FIRE 911AC DACT or MS-5012 Slave Communicator)*
NFPA 72 Local (Automatic, Manual, Waterflow and Sprinkler Supervisory) Fire Alarm Systems
NFPA 72 Auxiliary (Automatic, Manual, and Waterflow) Fire Alarm Systems. (Requires 4XTM)
NFPA 72 Remote Station (Automatic, Manual, and Waterflow) Fire Alarm Systems. Requires
4XTM, NOTI•FIRE 911AC DACT*
NFPA 2001 Clean Agent Fire Extinguishing Systems
*Applications which require the NOTI•FIRE 911AC are not FM approved.
Additional Information
Before proceeding, the installer should be familiar with the following documents and
standards:
NFPA Standards:
NFPA 12 CO2 Fire Extinguishing Systems
NFPA 12A Halon 1301 Fire Extinguishing Systems
NFPA 12B Halon 1211 Fire Extinguishing Systems
NFPA 72 Installation, Maintenance and Use of Central Station Signaling Systems
NFPA 72 Local, Auxiliary, Remote Station and Proprietary Fire Alarm Systems
NFPA 72 Automatic Fire Detectors
NFPA 72 Installation, Maintenance and Use of Notification Appliances for Fire Alarm Systems
NFPA 72 Testing Procedures for Signaling Systems
NFPA 2001 Clean Agent Fire Extinguishing Systems
Underwriters Laboratories Documents:

UL 38 Manual Actuated Signaling Boxes
UL 217 Smoke Detectors, Single and Multiple Station
UL 228 Door Closers - Holders for Fire Alarm Systems
UL 268 Smoke Detectors for Fire Alarm Systems
UL 268A Smoke Detectors for Duct Applications
UL 346 Waterflow Indicators for Fire Alarm systems
UL 464 Audible Signaling Appliances
UL 521 Heat Detectors for Fire Alarm Systems
UL 864 Standard for Control Units for Fire Alarm Systems
UL 1481 Power Supplies for Fire Alarm Systems
UL 1638 Visual Signaling Appliances
UL 1971 Signaling Devices for the Hearing Impaired
CAN/ULC-S524-M91 Standard for Installation of Fire Alarm Systems
CAN/ULC-S527-M87 Standard for Control Units for Fire Alarm Systems
Other:
NEC Article 300 Wiring Methods
NEC Article 760 Fire Alarm Systems
Applicable Local and State Building Codes
Requirements of the Local Authority Having Jurisdiction
Notifier Device Compatibility Document, 15378
ADA Americans with Disabilities Act
The PDRP-1002 PN 51135:A 03/11/99 5

1 The PDRP-1002/PDRP-1002E Input Circuits
1 The PDRP-1002/PDRP-1002E
Features
• Microprocessor-controlled
• Power-limited on all circuits except Municipal Box output
• Alarm and trouble resound
• Four Class A (Style D)/Class B (Style B) Initiating Device Circuits
• Two Class A (Style Z)/Class B (Style Y) Notification Appliance circuits
• Two Class B (Style Y) Release Circuits
• General alarm and trouble relays
• Optional module for 4 zone/function relays (4XZM)
• Optional transmitter module (4XTM). Complies with NFPA 72 Auxiliary and
Remote Station Fire Alarm systems
• Optional volt/amp meter module (4XMM)
• Optional supervised remote annunciator (RZA-4X)
• Requires LED Interface Module (4XLM)
• Optional digital communicator (NOTI•FIRE 911AC)*
• Complies with NFPA 72 Central Station and Remote Station Fire Alarm Systems
• Supervisory Input Option
• Delay timer (adjustable)
• Three abort function options
• Designed for suppression standards NFPA 12, 12A and 12B
• Disable/enable controls per initiating zone
• Last Event Recall
• Battery/Earth fault supervision
• Fuse protection on all Notification/Release Circuits
• RMS regulated output power, 2.25 amps
• 7 amp/hour to 15 amp/hour battery options, up to 90 hours standby
• Resettable and non-resettable regulated power outputs
• Extensive transient protection
• Watchdog timer to supervise microprocessor
• Output circuits protected against false activations
• Slide-in zone identification labels
• Steel cabinet 14.5 in (368.3 mm) wide by 16 in ( 406.4 mm) high by 5 in (127 mm)
deep
• Dead-front dress panel option (DP-4X)
• Trim ring for flush mount between 16 in (406.4 mm) center studs (TR-4XR)
• Abort and manual release circuits
• Cross-zone option
Circuits
Input Circuits
Detector Zone 1, Class A (Style D)/Class B (Style B)
Detector Zone 2, Class A (Style D)/Class B (Style B)
Abort, Class A (Style D)/Class B (Style B)
Manual Release, Class A (Style D)/Class B (Style B)
Output circuits (optional auxiliary relays track these four circuits)

Notification Appliance Circuit 1, Class A(Style Z)/Class B (Style Y)
Notification appliance Circuit 2, Class A(Style Z)/Class B (Style Y)
Releasing Circuit 1, Class B (Style Y)
Releasing Circuit 2, Class B (Style Y)/Supervisory Input, Class B (Style B)
6 The PDRP-1002 PN 51135:A 03/11/99

Front Panel Control Switches 1 The PDRP-1002/PDRP-1002E
Front Panel Control Switches

Switch 1 Tone Silence
Switch 2 Alarm Silence
Switch 3 Alarm Activate
Switch 4 System Reset
NON-RESETTABLE
RMS-REGULATED
Notification Appliance Initiating Device
Releasing
RESETTABLE
Circuits
REGULATED
REGULATED
Circuits Relays
Class A (Style Z) Circuits Class A (Style D) Abort Manual
24 VVU Switch Release
24 VNR
Class B (Style Y) Alarm Trouble Class B (Style B)
24 VR
1 2 3 4 Contacts Contacts 1 2 3 4
+24VU +24VR +24VNR
+ - + - + - B+ A+ A- B- B+ A+ A- B- B+ B- B+ B- NO NC C NO NC C B+ A+ A- B- B+ A+ A- B- B+ A+ A- B- B+ A+ A- B-
TB1 TB4
TB2 TB3
JP 1 NO DACT
DACT
SUPV 2
4XTM
GEN ALM2
or
J1 Transformer
4XLM
AC Circuit Breaker
or
4XZM
Ground TB5
Neutral *Jumper “OPT 1” must

be cut if a module is
Hot
installed in this position
J2 Optional Ammeter
Connection
OPT 1*
J9
- Batteries
+
J3 Optional
4XTM
VoltmeterConnection
or
4XLM
or
4XZM
*Jumper “OPT 2” must
be cut if a module is
4XRP1002.cdr
installed in this position
OPT 2*
O1 2 3 4 5 6
N
BATT EARTH SW1
Cross Zone Abort Option
Supervisory Abort Option Micro Fail LED
Battery Fail LED Ground Fault LED Delay Timer Delay Timer
Figure 1 PDRP-1002/PDRP-1002E Installation Diagram
The PDRP-1002 PN 51135:A 03/11/99 7

1 The PDRP-1002/PDRP-1002E Transmitter Module (4XTM - NOTIFIER)
Optional Boards
The PDRP-1002/PDRP-1002E has mounting slots for two option boards. Any two of
the three option modules may be installed.
Transmitter Module (4XTM - NOTIFIER)

The Transmitter Module provides a supervised output for
local energy municipal box transmitter (for NFPA 72
Auxiliary Fire Alarm System) and alarm and trouble
reverse polarity circuits (for NFPA 72 Remote Station Fire
Alarm System). Also included is a DISABLE switch and
disable trouble LED.
As a jumper option, the alarm reverse polarity circuit will

open on trouble if no alarm exists.
4XTM.cdr
LED Interface Module (4XLM - NOTIFIER)
The LED Interface Module supports the RZA-4X Remote
Annunciator module. Annunciator wiring is supervised for
open conditions by this module. The Annunciator Driver
Module mounts to the main board, occupying one of the
two option connectors.
4XLM.cdr
Zone Relay Module (4XZM - NOTIFIER)
The Zone Relay module provides Form-C contacts for the
following:
As a jumper option, the first four relays described below can

be made silenceable.
DIP 1=OFF DIP 1=ON If Supervisory (DIP 2=ON)

Either Zone Cross Zone Either Zone Cross Zone
Alarm Detected First Alarm Alarm Detected First Alarm
Alarm Detected Second Alarm Alarm Detected Second Alarm
Release 1 Release 1 Release Release
Release 2 Release 2 Not Used Not Used
4XZM.cdr
8 The PDRP-1002 PN 51135:A 03/11/99

Transmitter Module (4XTM - NOTIFIER) 1 The PDRP-1002/PDRP-1002E
Transmitter Module (4XTM - NOTIFIER)

For Local Energy Municipal Box service (NFPA 72 Auxiliary Fire Alarm System)
Supervisory current: 5.0 mA
Trip current: 0.35 amps. (Subtracted from Notification Appliance power)
Coil Voltage: 3.65 VDC
Coil resistance: 14.6 ohms
Maximum allowable wire resistance between panel and trip coil: 3 ohms
Municipal Box wiring can leave the building
For Remote Station service (NFPA 72 Remote Station Fire Alarm

System):
Maximum load for each circuit: 10mA
Reverse polarity output voltage: 24 VDC
Remote Alarm and Remote Trouble wiring can leave the building
LED Interface Module (4XLM - NOTIFIER)

Maximum voltage/current, each output: 27.6V/8mA
Note: Outputs are power limited
Zone Relay Module (4XZM - NOTIFIER)

Dry Form-C contacts rated: 2.0 amps @ 30VDC (resistive), 0.5 amps @ 30 VAC
(resistive)
Remote Annunciator
Remote Annunciator (RZA-4X - NOTIFIER)
The Remote Annunciator mounts on a standard single-
gang box, and provides LED indication of the same
functions as the zone relay module. For example with
DIP 1=ON and DIP 2=OFF:
• One Zone in Alarm (red)
• Two Zones in Alarm (red)
• Releasing Circuit 1 (red)
• Releasing Circuit 2 (red)
• System Trouble (yellow)
A Local Trouble Sounder and Silence Switch are also
provided. All LED wiring is supervised for open
RZA4Xfr.cdr
conditions. Any open condition will cause the System
Trouble LED to illuminate.
Note: The Remote Annunciator requires the use of an LED Interface module (4XLM).
Optional Meters
Voltage, Current Meters (4XMM - NOTIFIER)
The Meter Module provides a voltmeter to measure the
10 20
voltage across the batteries and an ammeter to measure 0 30
the charging current to the batteries. The meters are

DC VOLTS
provided as an assembly that mounts to the lower left-
hand corner of the cabinet.
0
5 5
DC AMPERES
voltmter.cdr
The PDRP-1002 PN 51135:A 03/11/99 9

1 The PDRP-1002/PDRP-1002E AC Power
Specifications
AC Power
For the PDRP-1002: 120 VAC, 50/60 Hz, 1.2 amps AC Circuit
For the PDRP-1002E: 220/240 VAC, 50 Hz, 0.6 amps Breaker
Wire size: minimum #14 AWG with 600V insulation
Battery (lead acid only)
Maximum Charging Circuit: 27.6V, 1.5 amps
Maximum Battery Capacity: 15 AH. (Batteries larger
Acctbrkr.cdr
than 12 AH require NOTIFIER #BB-17 or other UL
listed external battery cabinet.)
Initiating Device Circuits
Power-limited circuitry
Operation: Class A (Style D)/Class B (Style B)
Normal Operating Voltage: 24 VDC (ripple = 1.0V peak-to-peak)
Alarm current: 15 mA minimum
Short circuit current: 40 mA maximum
Maximum detector current in standby: 2 mA (max) per zone
Maximum loop resistance: 200 ohms
End-of-line resistor: 4.7K, 1/2-Watt (NOTIFIER part # 71252, UL listed)
Detector loop current is sufficient to ensure operation of one alarmed detector per zone.
Supervisory current: 5 mA (including end-of-line resistor)
Notification Appliance and Releasing Circuits
Power-limited circuitry
Maximum allowable voltage drop due to wiring: 2 VDC
Normal Operating Voltage: 24 VDC
Total current available to all external devices: 2.25 amps
Maximum signaling current per circuit: 1.5 amps
End-of-line resistor: 4.7K, 1/2-Watt (NOTIFIER part # 71252, UL listed)
Alarm and Trouble Relays
Dry Form-C contacts rated: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC
(resistive). All relays must be connected to a power limited power supply.
Four-wire Smoke Detector Power
Up to 200 mA is available for powering 4-wire smoke detectors.
Maximum ripple voltage: 1.0 V p/p
Non-resettable Power
Total DC current available from this output is up to 200 mA (subtracted from 4-wire
smoke power).
Maximum ripple voltage: 1.0 V p/p
RMS Regulated Power
Total DC current available for powering external devices is 0.5 amp (subtracted from
2.25 amps available to notification appliance circuits).
Maximum ripple voltage: 100 mV p/p
Note: For device compatibility, refer to Device Compatibility Chart.
10 The PDRP-1002 PN 51135:A 03/11/99

RMS Regulated Power 1 The PDRP-1002/PDRP-1002E
Cabinet = 5.375 in.

(136.53 mm)
Door = 14.625 in. Backbox = 4.750 in.
(371.48 mm) (120.65 mm)
Backbox = 14.5 in.
(368.3 mm)
Door = 16.125 in.

(409.58 mm)
Backbox = 16 in.
(406.4 mm)
1.5 in
(38.1 mm)
TR-4XR
RUBY RD
STEEL
16 GA.
16.094 in.
(408.79 mm)
14.594 in.
(370.69 mm)
RPCABDIM.cdr
Optional Trim Ring

TR-4XR
Figure 2 Cabinet Dimensions
The PDRP-1002 PN 51135:A 03/11/99 11

2 System Operation RMS Regulated Power
2 System Operation
WARNING:When used for CO2 releasing applications, observe proper
precautions as stated in NFPA 12. Do not enter the protected space unless physical
! lockout and other safety procedures are fully completed. Do not use software
disable functions in the panel as lockout.
System Status LEDs

Alarm, Trouble and Supervisory LEDs will flash on and off until the event(s) has been
acknowledged (TONE or ALARM SILENCE), at which point the LED will illuminate
steadily.
AC POWER
Green LED that illuminates steadily to
indicate presence of AC power.
SYSTEM ALARM
Red LED that flashes when an alarm
occurs.
RELEASE
Red LED that illuminates steadily when
release occurs.
SUPERVISORY
Yellow LED that flashes upon activation of
a supervisory device (such as tamper
switch) on Output 4 if selected (see
“Setting Mode of Operation” in Section 3
4Xoper2.cdr
of this manual).
BATT EARTH MICRO
FAIL
SYSTEM TROUBLE
Yellow LED that flashes for any trouble
condition, including those associated with option boards.
CIRCUIT TROUBLE
Yellow LED that flashes for trouble conditions on output circuits (notification and
releasing circuits).
ALARM SILENCED
Yellow LED that illuminates steadily when the ALARM SILENCE switch has been
pushed after an alarm.
POWER TROUBLE
Yellow LED that flashes for low or disconnected batteries and earth fault conditions.
BATT
Yellow LED that illuminates steadily on motherboard when battery is low or not
detected (not visible through door).
EARTH
Yellow LED that illuminates steadily on motherboard during a ground fault condition
(not visible through door)
MICRO FAIL
Yellow LED that illuminates on motherboard when watchdog timer detects
microprocessor failure (not visible through door)
12 The PDRP-1002 PN 51135:A 03/11/99

RMS Regulated Power 2 System Operation
Control Switches
Tone Silence
Acknowledge alarms, troubles and
supervisories. The panel has alarm and
trouble resound with LED flash of new
conditions. The flashing trouble LED(s)
illuminate steadily on TONE SILENCE and
the piezo sounder silences. A second trouble
will resound the piezo. The piezo has three
sounds for alarm, trouble, and supervisory.
Trouble conditions are self-restoring. Alarms
latch and require RESET to clear.
4XPTL.cdr
Alarm Silence
Acknowledge for alarms and supervisories.
The ALARM SILENCE switch will silence
the local piezo, change any flashing alarm
LEDs to steady, and turn off the notification
circuits (not the releasing circuits). The
“ALARM SILENCED” LED will illuminate.
Alarm silence is a latching function and
requires a RESET to clear.
Alarm Activate
The ALARM ACTIVATE switch may be used
to activate Notification Appliance Circuits.
ALARM ACTIVATE also activates the
System Alarm relay. ALARM Activate is a
latching function. Pressing ALARM
SILENCE silences the notification circuits
and System Alarm Relay and lights the Alarm
Silenced LED. Pressing RESET returns the
system to normal.
System Reset
The RESET switch breaks power to all
initiating circuits, 4-wire smoke power and
option boards and will clear any activated
output circuits. If any alarms or troubles still
exist after reset, they will reactivate the panel.
Holding RESET down will perform a LAMP
TEST function and will activate the piezo sounder.
Zone Status LEDs

The alarm and/or trouble LED(s)
will flash until the event(s) has ALARM LED
been acknowledged (TONE or Zone 1
TROUBLE LED
ALARM SILENCE), at which ALARM LED Zone 2
point the LED(s) will illuminate TROUBLE LED
steadily. ABORT LED
Abort
ABORT TROUBLE LED
MANUAL RELEASE Manual
MANUAL RELEASE TROUBLE LED Release
The PDRP-1002 PN 51135:A 03/11/99 13

2 System Operation RMS Regulated Power
Supervisory
Output circuit #4 is used as an input for monitoring supervisory devices such as valve
tamper switches (note that SW1 DIP switch #2 must be set “ON” -- see section “Setting
Mode of Operation”) By setting Switch short circuit on this input (activation of a N.O.
contact) will cause the supervisory LED to flash. The piezo sounder will generate a
unique sound. TONE SILENCE will silence the piezo and cause the LED to illuminate
steadily. Supervisory signals latch and require RESET to clear. An open circuit will be
reported as a circuit trouble.
Zone Disable
If a zone has been disabled, an alarm
that occurs on that zone will flash the
red zone LED, but not the piezo or any
output circuit. If both power sources
are removed from the system, all zones
will be re-enabled upon restoration of
power. Disable status will be lost.
The Zone Disable routine makes use of
the four panel switches as follows:
1. Press and hold in the TONE
SILENCE switch.
2. With the TONE SILENCE switch
held in, press (in sequence) the
4XPTL.cdr
ALARM SILENCE switch, the
ALARM ACTIVATE switch, and
then the RESET switch.
3. The Zone 1 Alarm LED will flash.
4. To disable Zone 1, press the RESET switch. The Zone 1 yellow LED will light to
show that the zone is disabled.
Note: The RESET switch toggles disable status for the selected zone.
5. To select the next zone, press the ALARM SILENCE switch.

6. To select the previous zone, press the ALARM ACTIVATE switch.
7. When disable selections are complete, release the TONE SILENCE switch.
If any zone has been disabled, the trouble relay will activate and System Trouble LED
will flash.
Last Event Recall

Last Event Recall allows the user to display the previous panel status. The last event
recall uses the four panel switches as follows:
1. Press and hold in the TONE SILENCE switch.
2. With the TONE SILENCE switch held in, press (in sequence) the RESET switch,
the ALARM ACTIVATE switch, and then the ALARM SILENCE switch.
3. Last Event is displayed.
4. Release the TONE SILENCE switch to return to normal operation.
Note: To clear the last event buffer, press RESET twice.
14 The PDRP-1002 PN 51135:A 03/11/99

UL Power Limited Wiring Requirements 3 Installation Procedure
3 Installation Procedure
General
Carefully unpack the system and check for shipping damage. Mount the cabinet in a
clean dry, vibration-free area in which extreme temperatures are not encountered. The
location should be readily accessible with sufficient room for easy installation and
maintenance. Locate the top of the cabinet approximately five feet above the floor with
the hinge mounting on the left. Determine the number of conductors required for the
devices to be employed. Pull required conductors into the box through the knockout
provided. All wiring should be in accordance with the National and/or Local codes for
fire alarm systems.
UL Power Limited Wiring Requirements

Power limited and non-power limited circuit wiring must remain separated in the
cabinet. All power limited circuit wiring must remain at least 0.25 in (6.35 mm) away
from any non-power limited circuit wiring. Furthermore, all power limited circuit
wiring and non-power limited circuit wiring must enter and exit the cabinet through
different knockouts and/or conduits. A typical wiring diagram for the PDRP-1002/
PDRP-1002E is shown below.
Power Limited
Non-Power
Circuits Power Limited
Limited Circuits
Circuits
Relays Initiating Circuits

Notification Appliance
Circuits
4XTM
AC Power
Power Limited
Circuit
4XZM
Non-Power
PC Board Limited Circuit
RP1002PL.cdr
Figure 3 Typical Wiring Diagram for UL Power Limited Requirements
The PDRP-1002 PN 51135:A 03/11/99 15

3 Installation Procedure Zones
Initiating Device Circuits

Zones
Wire all alarm initiating devices sequentially for proper supervision. Initiating devices
include: heat, photoelectric, and ionization type detectors; and waterflow alarm
devices. Refer to the Compatibility Chart in Appendix B.
Note:
• Observe polarity when connecting polarized devices.
• All circuits are supervised and power limited.
• Leave Dummy Load (provided) on all unused circuits.
Class B (Style B)
Initiating Device Circuit
4.7K, 1/2-Watt (part # 71252 UL listed)
Class A (Style D)
Initiating Device
Two-wire
+ _ Circuit_
Smoke +
Detector Abort Switch Manual Release
4.7K, 1/2-Watt 4.7K, 1/2-Watt
+ _ _ (part # 71252 (part # 71252

Heat + UL listed) UL listed)
Detector
+ _ _
Manual +
Pull Station
TB4
B+ A+ A- B- B+ A+ A- B- B+ A+ A- B- B+ A+ A- B-
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
AIDEX.cdr
IN #1 IN #2 IN #3 IN #4
Figure 4 Example of an Alarm Initiating Device
16 The PDRP-1002 PN 51135:A 03/11/99

Zones 3 Installation Procedure
4-Wire Smoke Detector Connections

Refer to the Device Compatibility Document for suitable 4-wire smoke detectors.
24 VDC (+) 24 +VDC+ (+) Red

+ +
Common (-) Common (-) Black

- - - -
IDC (+) IDC (+)

+ + + +
- - - -
IDC (-) IDC (-)
UL listed
4.7K, 1/2-Watt
Listed
UL listed 24 VDC ELR
Power
Four-wire Smoke Detectors Supervision
Relay
TB1 TB4
+ - B+ A+ A- B-
1 2 3 4 1 2 3 4
RP4WR.cdr
+24VR IN #1
Class B Initiating Device Circuit
A maximum of 200mA is available from the +24VDC
4-wire smoke detector power circuit on TB1 terminals 3 Initiating Device Circuits 1,2,3, or 4
and 4. Any power that is drawn from the +24VDC Non- can be used. Class A (Style D) wiring
resettable Power on TB2 terminals 1 and 2 must be can also be employed.
subtracted from available 4-wire detector power. (See
“Specifications” and “Power” sections.)
Figure 5 Diagram of Connections for a 4-Wire Smoke Detector
Notes on Class A (Style D) and Class B (Style B) field wiring:

1) The Power Supervision Relay coil leads must be connected to the last detector
base 24V screw terminals.
2) Calculation of the maximum allowable resistance in the 24VDC detector power
wiring:
RMAX = (20.6 - VOM)
_________________________________________________________________________________________
(N x IS) + (NA x IA) + (IR)

Where:
RMAX is the maximum resistance of the 24V wires.
VOM is the minimum operating voltage of the detector or end-of-line relay, whichever is
greater, in volts.
N is the total number of detectors on the 24V supply loop.
IS is the detector current standby.
NA is the number of detectors on the 24V power loop which must function at the same
time in alarm.
IA is the detector current in alarm.
IR is the end-of-line relay current.
The PDRP-1002 PN 51135:A 03/11/99 17

3 Installation Procedure Notification Appliance Circuits
Output Circuits
Notification Appliance Circuits
This control panel can provide two Class A (Style Z)/Class B (Style Y) Notification
Appliance Circuits and two Class B (Style Y) Releasing Circuits (see section “Setting
Mode of Operation” for DIP switch configuration). Each circuit is capable of 1.5 amps
of current. Total current drawn from all four circuits cannot exceed 2.25 amps. Refer
to the Compatibility Chart. Circuits are supervised and power-limited.
Note: Wiring must be configured to maintain a minimum voltage of 20.4V on release circuits. Calculation of
maximum allowable resistance:
RMAX = 20.6V-20.4V
________________________________________________________________________
IS
Where: RMAX = maximum allowable resistance of wiring
IS = solenoid current
Class B (Style Y) Notification

Appliance Circuit
4.7K, 1/2-Watt
Class A (part #71252 UL listed)
(Style Z)
Notification
Appliance Circuit
Polarized Bell + - + -
Releasing Circuits
Polarized Strobe UL listed & FM approved

Releasing Devices
Polarized Horn +- +-
No Connection
No Connection
B+ A+ A- B- B+ A+ A- B- NC B+ B- NC B+ B-
TB2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
OUT #1 OUT #2 OUT #3 OUT #4
See note
below
4.7K, 1/4-Watt 4.7K, 1/4-Watt
Dummy Load all Dummy Load all

B+ A+ A- B- B+ B-
RPNAC.cdr
unused Notification unused Releasing

Appliance Circuits Circuits
Note: Output #4 can be configured for releasing or supervisory circuit (see Section “Setting Mode of Opera
configured as a releasing circuit, the circuit will be non-power limited. If configured as a supervisory circuit,
will be power limited. All wiring must follow the power limited “General” Section.
Figure 6 Notification Appliance Circuits
18 The PDRP-1002 PN 51135:A 03/11/99

Alarm Relay 3 Installation Procedure
Alarm Relay
One Form-C dry alarm contact is provided in the basic panel for controlling
supplementary devices. It is rated 2 amps at 30 VDC and 0.5 amps at 30 VAC
(resistive), and is non-silenceable when an alarm occurs. See below for terminal
location.
Trouble Relay
One Form-C dry trouble contact is provided in the basic panel for controlling
supplementary devices. It is rated 2 amps at 30 VDC and 0.5 amps at 30 VAC
(resistive), and will silence when trouble condition is cleared. See below for terminal
location.
Note: The alarm and trouble Form-C dry contact relays must be power limited relays. They must be wired
from one of the 24V power limited terminals as shown in the figure below or a comparable UL listed power
limited power supply.
Alarm Trouble
NO NC C NO NC C
or or
TB1 TB2 TB3
RPALMTBL.CDR
1 2 3 4 1 2 1 2 3 4 5 6
+24VU +24VR +24VNR
Alarm Trouble
Schematic representation of
Alarm/Trouble coils and contacts.
Figure 7 Alarm/Trouble Coils and Contacts
Power
CAUTION: Several different sources of power can be connected to this panel.
! Disconnect all sources of power before servicing. The panel and associated equipment
may be damaged by removing and/or inserting cards, modules, or interconnecting
cables while this unit is energized.
This output is not suitable The combined current draws from the Resettable
for powering devices and Non-resettable outputs cannot exceed 200 mA.
requiring filtered DC power.
RMS-Regulated Power 4-Wire Smoke Detector Power Non-resettable Power

24 VDC power for inductive- 24 VDC filtered, resettable power 24 VDC filtered, nonresettable
type devices such as door for 4-wire smoke detectors can be power can be drawn from TB2
holders can be connected to TB1 obtained from TB1 Terminals 3(+) Terminals 1 (+) and 2(-).
terminals 1 (+) and 2(-). and 4(-).
+24VU +24VR +24VNR

+ - + - + -
RPPWRTRM.cdr
TB 1 TB 2
1 2 3 4 1 2
Figure 8 Diagram of Power Terminals
The PDRP-1002 PN 51135:A 03/11/99 19

3 Installation Procedure AC Power
AC Power
Primary power required for the PDRP-1002 panel is 120 VAC, 50/60 Hz, 1.2 amps and
primary power for the PDRP-1002E is 220/240 VAC, 50 Hz, 0.6 amps. Overcurrent
protection for this circuit must comply with Article 760 of the National Electrical Code
(NEC) and/or local codes. Use #14 AWG (2.00 mm2)or larger wire with 600 volt rating.
Battery Power
Observe polarity when connecting battery. Connect battery cable to J9 on the main
board using the plug-in connector provided. See Appendix A for calculation of correct
battery rating.
CAUTION: Batteries contain sulfuric acid which can cause severe burns to the skin and
! eyes, and can destroy fabrics. If contact is made with sulfuric acid, immediately flush
skin or eyes with water for 15 minutes and seek immediate medical attention.
Voltmeter/Ammeter
To monitor battery voltage and battery charging current, a 4XMM (NOTIFIER) is
required. To install the power meter module, remove the jumper labeled “AMP” and
connect cable assembly P2 to pin connector J2 and cable assembly P3 to pin connector
J3 on the main board. Secure the 4XMM to the backbox with the two screws provided.
On some models, it will be necessary to install the meter bracket with the nuts and bolts
provided.
P2
J2
J9
P3
J3
10 20
0 30
DC VOLTS
0
5 5
DC AMPERES
RPMBVM.cdr
Figure 9 Diagram of the 4XMM Voltmeter Connected to the Main Board
20 The PDRP-1002 PN 51135:A 03/11/99

Voltmeter/Ammeter 3 Installation Procedure
Optional Modules
The fire control panel has two module connectors - J5 and J8. Three modules are
available for the panel and they can be used in any combination, including duplicate
modules. The corresponding option jumper must be cut before installation of an
optional module.
Transformer
J4
*Jumper “OPT 1”
Ground J5 must be cut if a
Neutral
module is
installed in this
Hot
position
Optional Ammeter
Connection
Batteries
Optional
VoltmeterConnection
*Jumper “OPT 2”
J7 must be cut if a
module is
J8 installed in this
position
4XRP102a.cdr
Cross Zone Abort Option
Supervisory Abort Option Micro Fail LED
Battery Fail LED Ground Fault LED Delay Timer Delay Timer
Note:
• Optional 4XLM module for an RZA-4X Annunciator must be installed on J7 and J8 only.
• 4XTM and 4XZM modules can be installed in either location.
Figure 10 Optional Panel Modules
The PDRP-1002 PN 51135:A 03/11/99 21

3 Installation Procedure Installing Option Modules
Installing Option Modules

Insert the two stand-offs (provided) into the holes located on the right-side edge of the
main board. Carefully align the pins on the main board with J1 and/or J2 on the option
board. Insert screw through the option board until it is secured on the stand-offs. Affix
the terminal identification labels provided with the option modules as shown below.
(Part # 42050)
Stand-offs)
Main
Option Board Board
(4XZM shown)
4XSTNOFF.cdr
4XOPTNBD.cdr
Figure 11 Installing Option Modules.
22 The PDRP-1002 PN 51135:A 03/11/99

Transmitter Module - 4XTM (NOTIFIER) 3 Installation Procedure
Transmitter Module - 4XTM (NOTIFIER)

Polarities shown in activated positions. The wiring of this module must follow the
requirements as specified in the “General” section, “UL Power Limited Wiring
Requirements.”
1 + } Remote Alarm
2 - Power Limited Circuit
3 + Remote Trouble
4 -}
5 No Connection
6 + Municipal Box*
-}
Non-Power Limited Circui
7
TBL Jumper
* Dummy load terminals
6 and 7 (4.7K, 1/4 W
Disconnect LED resistor) if Municipal
Box is not connected.
4XTBa.cdr
Disconnect Switch
Push the disconnect switch down to prevent unwanted activation of the Municipal Box
and Remote Station Outputs during testing of the control panel. The Disconnect LED
will remain illuminated while the Municipal Box is disconnected. The System Trouble
LED will indicate disconnected and/or Open Circuit conditions on the Municipal box.
Cutting the TBL jumper will allow the alarm reverse polarity circuit to open on trouble,
if no alarm exists.
Note: Remote Alarm, Remote Trouble, and Municipal Box wiring can leave the building.
The PDRP-1002 PN 51135:A 03/11/99 23

3 Installation Procedure Zone Relay Module - 4XZM (NOTIFIER)
Zone Relay Module - 4XZM (NOTIFIER)

Non-power limited and power limited wiring must have a minimum distance of 0.25 in.
(6.35 mm) wire to wire. If this module is used to drive non-power limited and power
limited circuits, please follow the instructions below.
Relay #1 through #4 will activate with Output #1 through #4

and remain latched unless jumper “LATCH” is cut.
1 NO
2 NC Relay #1
3 C
4 NO
5 NC Relay #2
6 C
7 NO
8 NC Relay #3
9 C
10 NO
11 NC Relay #4
12 C
13 NO
14 NC Alarm
15 C
16 NO
17 NC Trouble
18 C
4XZMA.cdr
Use Disable switch to disconnect the relays.

Cut jumper for non-latching (silenceable) relay operation.
1) Skip a set of dry contacts to maintain the 0.25 in (6.35 mm) required space
between power limited and non-power limited circuits. The wiring of this module must
follow the requirements as specified in the “General” section, “UL Power Limited
Wiring Requirements.”
OR
2) If this module is needed to drive power limited and non-power limited relays that
are next to each other, refer to the figure below showing a typical connection.
NO
Relay #1 NC Power Limited Circuit
C
NO
Relay #2 NC Power Limited Circuit
C
NO No Connection
Relay #3 NC Non-power Limited Circuit
C
NO
Relay #4 NC
4XZMptl.cdr
Non-power Limited Circuit

C
Note: Refer to the Protected Premises Unit label, located on the door of the control panel, to
indicate if any dry contacts are to be used as non-power limited dry contacts.
24 The PDRP-1002 PN 51135:A 03/11/99

LED Interface Module - 4XLM (NOTIFIER) 3 Installation Procedure
LED Interface Module - 4XLM (NOTIFIER)

The wiring of this module must follow the requirements as specified in section”UL Power Limited Wiring
Requirements.”
1 +24V
2 Out#1
3 Out#2
4 Out#3
5 Out#4
6 System Trouble
7 Sound
8 Resound
4XLMa.cdr
Connect to corresponding terminals
of RZA-4X Remote Annunciator.
RZA4XBX.cdr
RZA4Xfr.cdr
Side View Single-gang Box
Front View Note: Make wiring connections with system

power off. Maximum wire impedance is 50
ohms per wiring connection.
Figure 12 LED Interface Module - 4XLM
The PDRP-1002 PN 51135:A 03/11/99 25

3 Installation Procedure DIP Switch
Setting Mode of Operation

DIP Switch
The DIP switch is located at the bottom of the PDRP-1002/PDRP-1002E main board.
To set a switch to the “ON” position, slide the switch up until it stops. The flush-
surface switches are designed to prevent accidentally changing a switch setting and may
therefore require use of a pen or screwdriver to set them.
4XRPDIPS.cdr
O1 2 3 4 5 6
N
Battery Fail
Micro Fail LED
LED
Ground Fault LED O 1 2 3 4 5 6
N
DIP Switches
Switch 3: DELAY TIMER
Switch 4: DELAY TIMER
Switch 1: CROSS ZONE
Switch 5: ABORT OPTION
Switch 2: SUPERVISORY
Switch 6: ABORT OPTION
Note: The Reset key must be depressed after any switch configuration has been made.
Cross Zone
Select the desired mode of operation and set SW1 DIP switch 1.
Switch 1 OFF ON
Output 1 is activated by an alarm on Output 1 (Pre-discharge alarm) is

either Zone 1 or Zone 2. activated by the first alarmed zone
in the system. Initiation of an alarm
on the other zone will shut this
output off.
Output 2 is activated by an alarm on Output 2 is activated when alarms

either Zone 1 or Zone 2. Output 2 occur on both Zone 1 and Zone 2.
will pulse at 60 ppm while timer is Output 2 will pulse at 60 ppm while
running or frozen by abort. Output 2 timer is running or frozen by abort.
will sound steadily upon release (time Output 2 will sound steadily upon
out). release (time out).
Outputs 3 and 4 will be activated when the timer expires (provided that
Output 4 is functioning as a releasing circuit - set via DIP Switch 2).
The Timer will start whenever an The Timer will start when alarms
alarm occurs on either Zone 1 or occur on both Zone 1 and Zone 2.
Zone 2.
Note: Outputs 1 and 2 refer to Notification Appliance Circuits. Output 3 refers to a releasing circuit. Output
4 is determined by setting switch 2. Zones 1 and 2 refer to Initiating Device Circuits.
26 The PDRP-1002 PN 51135:A 03/11/99

Output 4 Supervisory/Releasing Service 3 Installation Procedure
Output 4 Supervisory/Releasing Service

Set the function of Output 4 via SW1 DIP switch 2.
Switch 2 OFF ON
Output 4 will function as a Output 4 will function as a supervisory input

solenoid releasing circuit. This circuit. A short condition on this circuit will
circuit will be a non-power illuminate the Supervisory LED and sound
limited circuit in this mode. the supervisory tone on the piezo. An open
condition generates a circuit trouble
condition. This circuit will function as a
power limited circuit in this mode.
Timer
Select the desired Timer setting and set SW1 DIP switches 3 and 4 per the appropriate
column.
No Delay* 10 Seconds 20 Seconds 30 Seconds
Switch 3 OFF OFF ON ON
Switch 4 OFF ON OFF ON
*Abort switch is inoperative when no delay is selected.
Abort Function
Select the desired abort functions and set SW1 DIP switches 5 and 6 per the appropriate
column.
Switch 1 OFF OFF ON ON
Switch 2 OFF ON OFF ON
Standard UL-type IRI-type delay NYC-type delay Local Jurisdiction

delay timer which timer which timer. Pressing delay timer. Once
continues to count down functions the same as ABORT, once an the timer has started,
upon ABORT, and stops the UL-type timer alarm exists, changes pressing ABORT
and holds at 10 seconds with the exception timer value to the restores timer to its
until release of the that the ABORT will time selected via DIP full time as set on
ABORT switch. Upon function only if Switches 3 and 4 DIP Switches 3 and
release of the ABORT pressed and held plus 90 seconds. 4. The timer will
switch, the timer before 2nd zone goes The timer will not not start as long as
resumes the countdown into alarm. start as long as the ABORT is held.
at 10 seconds. ABORT switch is Release of the
held. SYSTEM ABORT switch
These modes are the only ones that RESET restores continues the
comply with UL Standard 864 timer to original countdown, whereas
times selected via pressing ABORT
DIP Switches 3 and again will restore
4. Successive the timer to its full
ABORTS will add value.
90 seconds to
selected timer value.
Note: ABORT timer will not operate when timer is set for “NO DELAY”.
The PDRP-1002 PN 51135:A 03/11/99 27

Appendix A: Power Calculations Standby Battery Requirements
Appendix A: Power Calculations

Standby Battery Requirements
The Standby Battery Current figure obtained in the following table (Table 1) represents
the amount of current that must be supplied by the secondary power source (batteries)
to sustain control panel operation for one hour.
Basic Control Panel 88 mA

Control panel with AC power off, System Trouble LED and audible trouble sounder on.
If using a 4XZM Zone Relay Module1 [ ] X 8 mA =
If using a 4XTM Transmitter Module, add 11 mA
If using the Reverse Polarity Alarm output, add 5 mA
If using the Reverse Polarity Trouble output, add 5 mA
If using a 4XLM/RZA-4X Driver/Annunciator combination:1

[ ] X 19 mA =
If using a 4XMM Meter Module, add 1 mA
If using the Noti•Fire 911AC DACT, add 30 mA
Number Device Total

in use Current Current
(see Appendix B for data)
a. Two-wire detector heads X =
b. Four-wire detector heads X =
c. End of Line Relays X 25.0 mA =
d. Add lines a, b, & c for
Place subtotal here
Add last column for Standby Battery Current :

and continue to next table (Table 2)
Table 1 Standby Battery Requirements

Note: The control panel will support the installation of one or two optional modules, including two of the
same type of module.
28 The PDRP-1002 PN 51135:A 03/11/99

Ampere-Hour Calculations Appendix A: Power Calculations
Ampere-Hour Calculations
Standby Battery Current StandbyTime

Convert the total from 24, 60, or 90
Table 1 to amps and enter hours
here
Standby
amps X hours =
amp/hours
Enter 0.25 for 5 minutes in alarm + Alarm

or 0.5 for 10 minutes in alarm amp/hours
Total amp/
Add Standby and Alarm amp/hours = hours needed
Table 2 Ampere-Hour Calculations

Select a battery with an equal or greater amp/hour rating than the figure obtained
in Table 2. Batteries must be lead-acid type.
PS-1270 12 volt, 7 amp/hour (two required)

PS-12120 12-volt, 12 amp/hour (two required)
Notes:
1. Alarm amp-hours assumes a maximum system draw of 3 amps in alarm for 5
minutes (0.25 amp/hour) or for 10 minutes (0.5 amp/hour)
2. NFPA 72 Central Station and Local and Proprietary Fire Alarm Systems require 24
hours of standby.
3. NFPA 72 Auxiliary and Remote Station Fire Alarm Systems require 60 hours of
standby.
4. Factory Mutual Systems require 90 hours of standby.
5. The battery charger in this panel will charge a maximum of 15 amp/hours of
batteries within 48 hours (7 amp/hour minimum). Batteries larger than 12 amp/
hour will require a UL listed battery cabinet (e.g. NOTIFIER BB-17).
The PDRP-1002 PN 51135:A 03/11/99 29

Appendix B: Device Compatibility FM-Approved Releasing Devices
Appendix B: Device Compatibility

Max Standby Max Alarm
Smoke Detector/Base Detector Type
Current (mA) Current (mA)
System Sensor 2424 Photoelectric 0.10 41
System Sensor 2424TH Photoelectric 0.10 41
System Sensor 2451TH (with/B402B Base) Photoelectric 0.10 39
System Sensor 1424 Ionization 0.10 41
System Sensor 1451 (w/B402B Base) Ionization 0.10 39
System Sensor 2412AT Photoelectric 0.12 58
System Sensor 2412TH Photoelectric 0.12 77
System Sensor 2312/24TB Photoelectric 0.12 50
System Sensor B112LP Base see note 39
System Sensor B114LP Base see note 75
System Sensor B404B Base see note see note
System Sensor 6424 Projected Beam 10 28.4
System Sensor DH400ACDCI Ionization Duct 25 95
System Sensor DH400ACDCP Photoelectric Duct 25 95
System Sensor 1112/24 Ionization 0.05 50
System Sensor 2112/24 Photoelectric 0.05 50
System Sensor 2112/24B Photoelectric 0.05 65
System Sensor 2112/24T Photoelectric w/135° 0.05 50

Thermal
System Sensor 2112/24TSRB Photoelectric w/135° 15 45

Thermal Supervisory Relay
Note: Contact manufacturer for currents.
Table 3 UL Listed Four-Wire Smoke Detectors
FM-Approved Releasing Devices

(System Sensor’s PDRP-1002/PDRP-1002E)
Solenoid Group [A]
Skinner solenoid valve Model LV2LBX25, 24 VDC, 11 Watts, 458 mA, 1/2 in. NPS, 5/
8 in. orifice.
Solenoid Group [B] These valves are interchangeable.
ASCO solenoid valve Model T8210A107, 24 VDC, 16.8 Watts, 700 mA, 1/2 in. NPS,
5/8 in. orifice.
ASCO solenoid valve Model R8210A107, 24 VDC, 16.8 Watts, 700 mA, 1/2 in. NPS,
5/8 in. orifice.
ASCO solenoid valve Model 8210A107, 24 VDC, 16.8 Watts, 700 mA, 1/2 in. NPS, 5/
30 The PDRP-1002 PN 51135:A 03/11/99

FM-Approved Releasing Devices Appendix B: Device Compatibility
8 in. orifice.
Solenoid Group [C]
Star Sprinkler Corp. Solenoid P/N 5550, 24 VDC, part of Model D deluge valve.
Kidde-Fenwal Electric Control Head P/N 890181; 24V, 2.0 Amps
Kidde-Fenwal Electric Control Head P/N 899175; 24V, 2.0 Amps
Kidde-Fenwal Electric Control Head Stackable (XP) P/N 48650001; 24V, 0.2 Amps
Kidde-Fenwal Electric and Cable Op Control Head (XP) P/N 897494; 24V, 1.5 Amps,
33 Watts
Refer to the FM approval guide for automatic water control valves which are
compatible with solenoids listed above.
Model Type Current (mA)
FM980-24 Floor Mount, single 68
FM996-24 Wall Mount Surface Wiring 68
FM998-24 Wall Mount Concealed Wiring 68
Table 4 24 VDC Door Holders
Vendor Model Current(mA)
System Sensor A77-716B 20
Air Products & Controls, LTD MR-101/C 15

MR-201/C 35
Table 5 UL Listed 24 VDC Relays
The PDRP-1002 PN 51135:A 03/11/99 31

Rated FWR Filtered

SYSTEM SENSOR
Voltage² DC DC
System Sensor MA-12/24D Electronic Sounder 24VDC 73 46
System Sensor SS24 Strobe 24VDC note 5 30
System Sensor SS24LO Strobe 24VDC 45 25
System Sensor SS24LOC Ceiling Strobe (SS24LOBC - beige) 24VDC 45 25
System Sensor SS24M Strobe 24VDC 125 75
System Sensor SS24MC Ceiling Strobe 24VDC 125 75
System Sensor MASS24D Electronic Sounder/Strobe 24VDC 118 71
System Sensor MASS24LO Electronic Sounder/Strobe 24VDC 118 71
System Sensor MASS24LOC Electronic Ceiling Sounder/Strobe 24VDC 118 71
System Sensor MASS24LOLA Electronic Sounder/Strobe with Fuego lens 24VDC 118 71
System Sensor MASS24M Electronic Sounder/Strobe 24VDC 198 121
System Sensor MASS24MC Electronic Ceiling Sounder/Strobe 24VDC 198 121
System Sensor PA400R Sounder 24VDC note 5 15
System Sensor PS24LO Add-on Strobe 24VDC 45 25
System Sensor SS2415ADA Signaling Strobe 24VDC 90 75
System Sensor SS241575ADA Signaling Strobe 24 VDC 120 93
System Sensor SS2415ADAS Signaling Strobe with Synch. Circuit 24 VDC 125 106
System Sensor SS241575ADAS Signaling Strobe with Synch. Circuit 24 VDC 180 115
System Sensor MASS2415ADA Sounder/Signaling Strobe 24VDC 163 121
System Sensor MASS241575ADA Sounder/Signaling Strobe 24 VDC 193 139
System Sensor MASS2415ADAS Sounder/Signaling Strobe w/ Synch. Ckt. 24 VDC 163 121
System Sensor MASS241575ADAS Sounder/Signaling Strobe w/ Synch. Ckt. 24 VDC 193 139
System Sensor PS2415ADA Mini-Sounder/Strobe 24VDC 110 90
System Sensor PS24110ADA Mini-Sounder/Strobe 24VDC 240 225¥
System Sensor SP1R2415ADA Speaker/Signaling Strobe 24VDC 90 75
32 The PDRP-1002 PN 51135:A 03/11/99

System Sensor SP1R241575ADA Speaker/Signaling Strobe 24 VDC 120 93
System Sensor V4R2415ADA Speaker/Signaling Strobe 24VDC 90 75
System Sensor V4R241575ADA Speaker/Signaling Strobe 24 VDC 120 93
System Sensor SP100W24LOC Ceiling Speaker/Strobe, 8" round grille 24VDC 45 25
System Sensor SP101R24LO Speaker/Strobe, 5" square grille 24VDC 45 25
System Sensor SP101R24M Speaker/Strobe, 5" square grille 24VDC 125 75
System Sensor SP100W24MC Ceiling Speaker/Strobe, 8" round grille 24VDC 125 75
System Sensor MA12/24EH Multi Alert Horn with Mechanical Tone 12VDC/ 20/64 38/43
24VDC
System Sensor MAEH24LO Multi Alert Horn with Mechanical Tone/Strobe 24VDC 109 68
System Sensor MAEH24LOC Multi Alert Horn with Mechanical Tone/Strobe 24VDC 109 68
System Sensor MAEH24LOLA Multi Alert Horn with Mechanical Tone/Strobe 24VDC 153 96
System Sensor MAEH24M Multi Alert Horn with Mechanical Tone/Strobe 24VDC 189 118
System Sensor MAEH24MC Multi Alert Horn with Mechanical Tone/Strobe 24VDC 189 118
System Sensor MAEH1215ADA Multi Alert Horn with Mechanical Tone/Strobe 12VDC 240 191
System Sensor MAEH2415ADAS Multi Alert Horn with Mechanical Tone/Strobe 24VDC 198 152
System Sensor MAEH241575ADAS Multi Alert Horn with Mechanical Tone/Strobe 24VDC 253 241
System Sensor H12 SpectrAlert Horn 12VDC 25 14
System Sensor H42 SpectrAlert Horn3 24VDC 42 37
System Sensor S1215 SpectrAlert Strobe 12VDC 159 133
System Sensor S121575 SpectrAlert Strobe 12VDC 182 168
System Sensor S2415 SpectrAlert Strobe3 24VDC 142 83
System Sensor P1215 SpectrAlert Horn/Strobe 12VDC 173 144
System Sensor P121575 SpectrAlert Horn/Strobe 12VDC 196 179
System Sensor P2415 SpectrAlert Horn/Strobe3 24VDC 165 94
The PDRP-1002 PN 51135:A 03/11/99 33

System Sensor P24110 SpectrAlert Strobe3 24VDC 265 214
System Sensor RP1215ADAARetrofit Strobe Plate 12VDC 200 170
System Sensor H24 SpectrAlert 24VDC 42 37
System Sensor S2415 SpectrAlertStrobe3 24VDC 142 83
System Sensor S2415 SpectrAlert Horn/Strobe3 24VDC 165 94
System Sensor S2415 SpectrAlertStrobe3 24VDC 142 83
Note:
1) Control panels suppling Special Application (FWR, Filtered) power must use the notification appliances,
relays or door holders listed in this table.
2) All currents are in Millamperes and worst case average.
3) Nominal Operating voltage.
4) Refer to Installation Instructions for more information.
5) Contact manufacturer for currents.
Table 6 UL Listed Notification Appliances
34 The PDRP-1002 PN 51135:A 03/11/99

Number of
Detectors Per Zone
Model Det. Detector Type Base Model Base Standby PDRP-1002/

ID ID Current PDRP-1002E
(uA)
System Sensor 1400 A Ionization n/a n/a 100 20
System Sensor 1451 A Ionization B401B / B406B A 120 15 / 1
System Sensor 1851DH A Ionization DH1851DC A 120 15
System Sensor 2400 A Photoelectric n/a n/a 120 15
System Sensor 2400AIT A Photo / Isolated n/a n/a 120 1

Thermal / Horn
System Sensor 2400AT A Photo / Thermal / Horn n/a n/a 120 1
System Sensor 2400TH A Photo / Thermal n/a n/a 120 15
System Sensor 2451 A Photoelectric B401B / B406B A 120 15 / 1
System Sensor 2451TH A Photo / Thermal B401B / B406B A 120 15 / 1
System Sensor 2851DH A Photoelectric DH2851DC A 120 15
System Sensor 1451DH A Ionization DH-400 A 120 15
System Sensor 2451 A Photoelectric DH-400 A 120 15
System Sensor 2300T A Photo / Thermal n/a n/a 120 15
System Sensor 1800 A Ionization n/a n/a 100 n/a
System Sensor 1851B A Ionization B101B A 120 n/a
System Sensor 1851B A Ionization B107B A 120 n/a
System Sensor 2800 A Photoelectric n/a n/a 120 n/a
System Sensor 2800TH A Photo / Thermal n/a n/a 120 n/a
System Sensor 2851B A Photoelectric B101B A 120 n/a
System Sensor 2851B A Photoelectric B107B A 120 n/a
System Sensor 2851BTH A Photo / Thermal B101B A 120 n/a
System Sensor 2851BTH A Photo / Thermal B107B A 120 n/a
System Sensor 1151 A Ionnization B401 / B110LP / A 120 15 / 15 / 1

B116LP
System Sensor 2151 A Photoelectric B401 / B110LP / A 120 15 / 15 / 1

B116LP
Table 7 UL Listed, Compatible Two-Wire Smoke Detectors for Notifier Control Panels
The PDRP-1002 PN 51135:A 03/11/99 35

Appendix C: NFPA Standard-Specific Requirements FM-Approved Releasing Devices
Appendix C: NFPA Standard-Specific Requirements

The PDRP-1002/PDRP-1002E has been designed for use in commercial, industrial, and
institutional applications and meets the requirements for service under the National Fire
Protection Association (NFPA) Standards outlined in this appendix. The minimum
system components required for compliance with the appropriate NFPA standards are
listed below.
PDRP-1002/PDRP-1002E Control Panel containing the main control board, cabinet
(backbox and door), main supply transformer and power supply.
Batteries (refer to Appendix A for Standby Power Requirements).
Initiating Devices - connected to one of the control panel’s Initiating Device Circuits.
Notification Appliances - connected to one of the control panel’s Notification
Appliance Circuits.
Releasing Devices - connected on one of the control panel’s Releasing Circuits.
The following additional equipment is needed for compliance with the NFPA standards
listed below.
NFPA 72 Signaling Systems for Central Station Service (Protected Premises Unit)
NOTI•FIRE 911AC DACT* - for connection to a compatible listed Central Station
DACR or Protected Premises Receiving Unit. This unit must be installed as outlined in
Figure 13.
NFPA 72 Auxiliary Fire Alarm System
4XTM Transmitter Module for connection to a compatible listed Local Energy
Municipal Box. This unit must be installed as outlined in Figure 15.
NFPA 72 Remote Station Fire Alarm System
4XTM Transmitter Module for connection to Fire•Lite RS82-9 Remote Station
Receiver. See Figure 16 for installation instructions.
OR
NOTI•FIRE 911AC DACT* - For connection to a compatible listed remote station
DACR. This unit must be installed as outlined in Figure 13.
36 The PDRP-1002 PN 51135:A 03/11/99

NFPA 72 Signaling Systems for Central Station Service Appendix C: NFPA Standard-Specific Requirements
NFPA 72 Signaling Systems for Central Station Service

(Protected Premises Unit) and Remote Station Fire Alarm System (Protected Premises Unit)
NOTI•FIRE 911AC DACT* - for connection to a Central Station Receiver or Protected
Premises Receiving Unit. This unit must be installed as illustrated below. For
additional information on the 911AC, refer to document 74-06200-005.
All connections between the FACP and 911AC must be in conduit, less than 20 ft
(609.6cm) in length in the same room. If the NOTI•FIRE 911AC is not mounted in the
PDRP-1002/PDRP-1002E backbox all connections must be in conduit, less than 20 ft.
(609.6 cm) in length in the same room.
*This application using the NOTI•FIRE 911AC is not FM approved.
Note: For 911AC
• The Maximum standby load shall be 125 mA.
• The Standby by Battery Requirement: 24VDC, 7Amp-Hour-Max.
• The PDRP-1002/PDRP-1002E is not suitable for transmission of a supervisory signal to the DACT.
NOTE on STD DACT:

Place jumper over pins 2 and 3,
marked DACT, when employing a
Note: The PDRP-1002/ DACT. This directs the control panel
PDRP-1002E is not 1 to transmit all trouble conditions
2
suitable for transmission 3

4
5
1
2
3
1 2VAC , 20VA, 60Hz or +2 4VD C
1 2VAC , 20VA, 60Hz or -2 4VD C
(R efer to m an ua l)
D i g it a l Ala rm C o mm u n ic a t or Tra n sm it t e r L i st e d for C e ntr al S ta t i o n o r R e m o te S ta t i on S e rv ic e.
S lid e C ov er B ack to A cces s Pro gr am m in g Ja c k a n d R el ay s

except AC LOSS.
6 4 B AT TE RY - - 1 2 V D C Se a le d
of a supervisory signal to 7
8
9
5
6
7
B AT TE RY +
INI T IAT IN G A1 -
INI T IAT IN G A2 -
+
R e c h a rg e ab le
B a tt e ry
8 INI T IAT IN G B1 +
10 A lte rn a te R J3 1 X
the DACT 11
12
9
10
11
12
INI T IAT IN G B2 +
S U PE RV IS OR Y H I
S U PE RV IS OR Y LO
T ROU B L E R EL AY N C
Te l co Ja c k
13 T ROU B L E R EL AY C O M
14 T ROU B L E R EL AY N O
P ri ma r y R J 31 X
15 A LA R M R ELAY N C Te l co Ja c k
16 A LA R M R ELAY C OM
17 A LA R M R ELAY N O
To AC -+
Power PS1270
12Volt
7AH Battery
Alarm
To Central Station
JP-1
STD DACT
Motherboard 911AC
Alarm TB3-1 6 and 7
normally open
contacts
TB3-3 8 and 9
RP911AC.CD
Trouble TB3-4 10
normally open
TB3-6 11
contacts
Figure 13 NFPA 72 Signaling Systems for Central Station Service
The PDRP-1002 PN 51135:A 03/11/99 37

Appendix C: NFPA Standard-Specific Requirements NFPA 72 Signaling Systems for Central Station Service
Using the MS-5012 as a DACT

1) Reference the MS-5012 manual for additional information.
2) Program the MS-5012 for slave applications.
3) The PDRP-1002/PDRP-1002E is not suitable for transmission of a supervisory
signal to the DACT.
Secondary
Phone Line
Modular Cable Primary
P/N MCBL-6 Phone Line
MS-5012
Alarm
TB2
J2
J3
Trouble
AC POWER TROUBLE
ALARM SUPERVISORY
1 2 3 F
TB3
4 5 6 E
1st
7 8 9 D EVENT
A O B C ENTER
STORE
Red
Yellow
120 VAC
Black
HOT
Yellow 12VDC
Neutral Battery
Black 2-7AH
Ground White
Green
AC Wiring for DACT/FACP must be

connected to the same circuit.
Motherboard MS-5012
MS5012X2.CDR
TB3-1 TB2-2
Alarm 12 3 4 5 6
TB3-3 TB2-1 TB3
PDRP-1002/PDRP-1002E
TB3-4 TB2-4
Trouble
TB3-6 TB2-3
Figure 14 Using the MS-5012 as a DACT
38 The PDRP-1002 PN 51135:A 03/11/99

NFPA 72 Auxiliary Fire Alarm System Appendix C: NFPA Standard-Specific Requirements
NFPA 72 Auxiliary Fire Alarm System

All connections are power limited and supervised. This application is not suitable for
separate transmission of sprinkler supervisory or trouble conditions.
Note: Maximum loop resistance allowed for wiring from control panel to Municipal Box is 3 ohms.
+ FIRE
Municipal Box Circuit
AUXPROSS.CDR
4XTB
+ - Gamewell
Model M34-56
6 Local Energy
Municipal Box
7
4XTM (NOTIFIER)
Transmitter Module
(activated polarities
shown)
Figure 15 NFPA 72 Auxiliary Fire Alarm System
The PDRP-1002 PN 51135:A 03/11/99 39

Appendix C: NFPA Standard-Specific Requirements NFPA 72 Remote Station Fire Alarm System
NFPA 72 Remote Station Fire Alarm System

Intended for connection to a polarity reversal circuit of a remote station receiving unit
having compatible ratings. All connections are power limited and supervised with the
exception of the reverse polarity loop. Supervision of the loop is the responsibility of
the receiver.
A.C. CKT BREAKER --

--
120 VAC K
N.C.2 9 1.2 AMPS --
DRY N.O.2 PRESS TO

--
--
Fire•Lite
SUPPLEMENTARY 10 RESET
CONTACTS, POLE 2 BATTERY GROUNDING RS82-9
11 SIGNALING 8
RATED RELAY FOR CKT FUSE TERMINAL Remote Station
N.C.1 8 AG 120 VAC 1.2 A
3A, 120 VAC
RESISTIVE
3A, 30 VDC
N.O.1
12
13
BELLS AND
DRY
CONTACTS
5A
125 V
7
6
}50-60 Hz Receiver
RESISTIVE POLE 1
INPUT UL listed
14 5 N/C
BATT +
CONTROL CARD K
CONN
(RSC) -
CIRCUIT SIDE FILTER
BELL
CAP 4 H 10 K
REMOTE STATION or
ELR
MASTER BOARD 3 HORN
(RSM-9) 2
ZONE CARD(RSZ)
CIRCUIT SIDE 1
2
OPTIONAL ZONE CARD
(RSZ) CIRCUIT SIDE 1
ALARM
OPTIONAL ZONE CARD
2
1
} SIGNAL
INPUT 3
(RSZ) CIRCUIT SIDE
ALARM
OPTIONAL ZONE CARD
2
1
} SIGNAL
INPUT 4
(RSZ) CIRCUIT SIDE
ALARM
OPTIONAL ZONE CARD
2
1
} SIGNAL
INPUT 5
(RSZ) CIRCUIT SIDE
OPTIONAL ZONE CARD

2
1
} ALARM
SIGNAL
(RSZ) CIRCUIT SIDE INPUT 6
ALARM
OPTIONAL ZONE CARD
2
1
} SIGNAL
INPUT 7
+ - + -
(RSZ) CIRCUIT SIDE ALARM
OPTIONAL ZONE CARD

2
1
} SIGNAL
INPUT 8
(RSZ) CIRCUIT SIDE ALARM
2
1
} SIGNAL
INPUT 9
OPTIONAL ZONE CARD
(RSZ) CIRCUIT SIDE
K | | | | | | | | | | K
Recommended Types:
ELPOWER EP 1250C
+ POWER SONIC PS 1245
Power Transformer POWER SONIC PS 1260
POWER SONIC PS 1265
YUASA NPG-12
or equivalent
- MAXIMUM BATTERY SIZE
6.0 X 2.6 X 4.1 in. (15.24 x 6.6 x10.41
1
Remote Alarm
2
3 Remote Trouble
4
REMPROSS.CDR
4XTM (NOTIFIER)
Transmitter Module
(activated polarities shown)
Figure 16 NFPA 72 Remote Station Fire Alarm System
40 The PDRP-1002 PN 51135:A 03/11/99

NFPA 72 Remote Station Fire Alarm System Appendix C: NFPA Standard-Specific Requirements
Troubleshooting Table
SYMPTOM PROBLEM SOLUTION

1. Check TB2 for proper connections. (TB3 for
4XB panels)
2. Remove all field wiring and install dummy ELR
at output circuit. Check for supervisory voltage
across it. (Normal -2.3 V). If problem persists,
Circuit trouble LED on Notification appliance circuit trouble replace circuit board.
3. Removed dummy ELR, reconnect field wiring
and measure voltage across output; (trouble -5V,
short OV).
4. Check for ELR at last device.
5. Check field wiring.
1. Check TB4 for proper connections.
2. Remove field wiring for zone in trouble and
Any of the right column install dummy ELR (4.7K for 24V; 2.2K for 12V).
Initiating zone open circuit trouble
yellow LEDs flashing If problem persists, replace circuit board.
3. Check for ELR at last device.
Any of the right column
System trouble LED on yellow LEDs steady on Zone Disable Check installation manual.
Missing or Check battery connections

Disconnected
1. Remove batteries, check voltage across charger
Battery trouble output (17 to 19V for 24V; 8-10V for 12V),
Batt yellow LED otherwise replace circuit board.
on Low or damage
2. Reconnect batteries, measure battery voltage at
battery
battery terminals. If voltage is less than 85% of
rated voltage, allow them to charge for 48 hours.
Power trouble LED on
AC Power LED on 3. If problem persists, replace batteries.
1. Remove field wiring from main panel and
optional module(s) (if installed). Install dummy
ELR (4.7K for 24V; 2.2K for 12V).
Ground fault trouble
2. Remove both battery leads.
Earth yellow LED on
3. If trouble clears, connect one circuit at a time to
pinpoint the problem.
4. If trouble doesn’t clear, replace circuit board.
Yellow LED on 4XTM on 4XTM 1. Move Municipal Box disconnect switch SW1 up
Install optional module(s) or replace jumper if
OPT1, OPT2 jumper cut
module(s) is not used.
1. Install dummy load if Municipal Box option
Municipal Box open circuit isn’t used.
2. Check Municipal Box wiring.
Remove field wiring and install ELR. If trouble
Any of the right column red LEDs on Short on initiating circuit wiring
clears, look for faulty or incorrectly wired devices.
Disconnecting Municipal Box switch on 4XTM Jumper for optional modules isn’t
Cut associated jumper OPT1 or OPT2.
does not create a trouble cut.
4XZM: associated LED does not activate for alarm, 1. Make sure module is properly installed.
Optional module trouble
trouble or supervisory conditions 2. Move disable switch SW1 on 4XZM to the left.
1. Make sure that 4XLM module is installed on J7
RZA-4X piezo doesn’t sound for alarm, trouble or
4XLM and J8.
supervisory conditions
Micro Fail yellow LED on Microprocessor damaged. Replace circuit board.
Power wasn’t removed prior to
All RZA-4X LEDs stay on Hit system reset.
installation.
Check incoming power (TB5). (TB1 for 4XB
Loss of main power
System trouble LED on panels)
AC Power LED off
Damaged circuit breaker Replace circuit board.
Micro Fail yellow LED on Microprocessor damaged Replace circuit board.
Table 8 Trouble Shooting Table
The PDRP-1002 PN 51135:A 03/11/99 41

Notes
42 The PDRP-1002 PN 51135:A 03/11/99

NFPA 72 Remote Station Fire Alarm System Appendix C: NFPA Standard-Specific Requirements
Notes
The PDRP-1002 PN 51135:A 03/11/99 43

Limited Warranty
System Sensor® warrants its products to be free from defects in materials and
workmanship for eighteen (18) months from the date of manufacture, under normal
use and service. Products are date stamped at time of manufacture. The sole and
exclusive obligation of System Sensor® is to repair or replace, at is option, free of
charge for parts and labor, any part which is defective in materials or workmanship
under normal use and service. For products not under System Sensor®
manufacturing date-stamp control, the warranty is eighteen (18) months from date of
original purchase by System Sensor® distributor unless the installation instructions
or catalog sets forth a shorter period, in which case the shorter period shall apply.
This warranty is void if the product is altered, repaired or serviced by anyone other
than System Sensor® or its authorized distributors or if there is a failure to maintain
the products and systems in which they operate in proper and workable manner. In
case of defect, phone System Sensor® Repair Department, RA #_____________,
3825 Ohio Avenue, St. Charles, IL 60174. Please include a note describing the
malfunction and suspected cause of failure.
This writing constitutes the only warranty made by System Sensor® with respect to
its products. System Sensor® does not represent that its products will prevent any
loss by fire or otherwise, or that its products will in all cases provide the protection for
which they are installed or intended. Buyer acknowledges that System Sensor® is
not an insurer and assumes no risk for loss or damages or the cost of any inconve-
nience, transportation, damage, misuse, abuse, accident or similar incident.
SYSTEM SENSOR® GIVES NO WARRANTY, EXPRESSED OR IMPLIED, OF

MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR
OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. UNDER NO CIRCUMSTANCES SHALL SYSTEM SENSOR® BE LIABLE
FOR ANY LOSS OF OR DAMAGE TO PROPERTY, DIRECT, INCIDENTAL OR
CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR INABILITY TO USE
SYSTEM SENSOR® PRODUCTS. FURTHERMORE, SYSTEM SENSOR® SHALL
NOT BE LIABLE FOR ANY PERSONAL INJURY OR DEATH WHICH MAY ARISE IN
THE COURSE OF, OR AS A RESULT OF, PERSONAL, COMMERCIAL OR
INDUSTRIAL USE OF ITS PRODUCTS.
This warranty replaces all previous warranties and is the only warranty made by
System Sensor®. No increase or alteration, written or verbal, of the obligation of this
warranty is authorized.
System Sensor
3825 Ohio Avenue, St. Charles, IL 60174
1-800-SENSOR2 Fax: 630-377-6495
44 The PDRP-1002 PN 51135:A 03/11/99

51135

Uploaded by

Document Informationclick to expand document informationWater Flow

Document Informationclick to expand document information

Copyright:

Available Formats

51135

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

51135

Uploaded by

Copyright:

Available Formats

System Sensor

3825 Ohio Avenue

2 The PDRP-1002 PN 51135:A 03/11/99

*Applications which require the NOTI•FIRE 911AC are not FM approved.

Underwriters Laboratories Documents:

The PDRP-1002 PN 51135:A 03/11/99 5

*Applications which require the NOTI•FIRE 911AC are not FM approved.

Output circuits (optional auxiliary relays track these four circuits)

6 The PDRP-1002 PN 51135:A 03/11/99

Front Panel Control Switches

Neutral *Jumper “OPT 1” must

installed in this position

Figure 1 PDRP-1002/PDRP-1002E Installation Diagram

The PDRP-1002 PN 51135:A 03/11/99 7

Transmitter Module (4XTM - NOTIFIER)

As a jumper option, the alarm reverse polarity circuit will

As a jumper option, the first four relays described below can

DIP 1=OFF DIP 1=ON If Supervisory (DIP 2=ON)

8 The PDRP-1002 PN 51135:A 03/11/99

Transmitter Module (4XTM - NOTIFIER)

For Remote Station service (NFPA 72 Remote Station Fire Alarm

LED Interface Module (4XLM - NOTIFIER)

Zone Relay Module (4XZM - NOTIFIER)

voltage across the batteries and an ammeter to measure 0 30

the charging current to the batteries. The meters are

The PDRP-1002 PN 51135:A 03/11/99 9

10 The PDRP-1002 PN 51135:A 03/11/99

Cabinet = 5.375 in.

Door = 16.125 in.

Optional Trim Ring

Figure 2 Cabinet Dimensions

The PDRP-1002 PN 51135:A 03/11/99 11

System Status LEDs

12 The PDRP-1002 PN 51135:A 03/11/99

Zone Status LEDs

The PDRP-1002 PN 51135:A 03/11/99 13

5. To select the next zone, press the ALARM SILENCE switch.

Last Event Recall

14 The PDRP-1002 PN 51135:A 03/11/99

UL Power Limited Wiring Requirements

Relays Initiating Circuits

Figure 3 Typical Wiring Diagram for UL Power Limited Requirements

The PDRP-1002 PN 51135:A 03/11/99 15

Initiating Device Circuits

+ _ _ (part # 71252 (part # 71252

Figure 4 Example of an Alarm Initiating Device

16 The PDRP-1002 PN 51135:A 03/11/99

4-Wire Smoke Detector Connections

24 VDC (+) 24 +VDC+ (+) Red

Common (-) Common (-) Black

IDC (+) IDC (+)

Figure 5 Diagram of Connections for a 4-Wire Smoke Detector

Notes on Class A (Style D) and Class B (Style B) field wiring:

(N x IS) + (NA x IA) + (IR)

The PDRP-1002 PN 51135:A 03/11/99 17

Class B (Style Y) Notification

Polarized Strobe UL listed & FM approved

4.7K, 1/4-Watt 4.7K, 1/4-Watt