Wa90 5 Vebm270100

Shop Manual VEBM270100
WA90-5
WA100M-5
WHEEL LOADER
MODEL: SERIAL NUMBER:
WA90-5 50051 AND UP
WA100M-5 50051 AND UP
• This shop manual may contain attachments and optional equipment that are not available in your area.
Please consult your local KOMATSU distributor for those items you may require. Materials and specifica-
tions are subject to change without notice.
• The Wheel Loaders WA90-5 and WA100M-5 are equipped with the engine S4D95LE-3
For details of this engine see Bulletin No. 3666418-00 (Cummins)
© 2005
All Rights Reserved
Printed in Europe 11/05
CONTENTS
No. of page
00 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .00-1
01 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .01-1
10 STRUCTURE AND FUNCTION . . . . . . . . . . . . . . . . . . . . . .10-1
20 TESTING AND ADJUSTING . . . . . . . . . . . . . . . . . . . . . . . .20-1
30 DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . .30-1
90 OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90-1
00-2 WA90-5 / WA100M-5

00 SAFETY
Safety notice ............................................ 00-3
Preparations for work ................................ 00-4
Tipping up the driver's cab ........................ 00-4
Tipping down the driver's cab ................... 00-6
Tipping up the driver's cab
(option with electric actuator) ......................... 00-8
Tipping down the driver's cab
(option with electric actuator) ......................... 00-10
Precautions during work ........................... 00-11
Hydraulic system ....................................... 00-12
Foreword .................................................. 00-13
How to read the shop manual .................. 00-14
Volumes .................................................... 00-14
Distribution and updating .......................... 00-14
Filing method ............................................ 00-14
Symbols .................................................... 00-15
Hoisting instructions ................................. 00-16
Wire ropes ................................................. 00-16
WA90-5 / WA100M-5 00-1

SAFETY
00-2 WA90-5 / WA100M-5

SAFETY Safety notice
Safety notice
Important Safety Notice

Proper service and repair is extremely important for safe
machine operation. Some of the described service and re-
pair techniques require the use of tools specially designed
by Komatsu for the specific purpose.
To prevent injury to workers, the symbol is used to
mark safety precautions in this manual. The cautions ac-
companying these symbols must always be followed care-
fully. If any dangerous situation arises or may possibly
arise, first consider safety, and take the necessary actions
to deal with the situation.
General Precautions
Mistakes in operation are extremely dangerous. Read the
OPERATION AND MAINTENANCE MANUAL carefully before
operating the machine! Always follow the safety rules valid
in your country carefully!
1. Before carrying out any greasing or repairs, read all the pre-
cautions given on the decals which are fixed to the machine.
2. When carrying out any operation, always wear safety shoes

and helmet. Do not wear loose work clothes, or clothes with
buttons missing.
• Always wear safety glasses when hitting parts with a

hammer.
• Always wear safety glasses when grinding parts with a

grinder, etc.
3. If welding repairs are needed, always have a trained, experi-

enced welder carry out the work. When carrying out welding
work, always wear welding gloves, apron, glasses, cap and
other clothes suited for welding work.
4. When carrying out any operation with two or more workers,

always agree on the operating procedure before starting. Al-
ways inform your fellow workers before starting any step of
the operation. Before starting work, hang UNDER REPAIR
signs on the controls in the operator's compartment.
WA90-5 / WA100M-5 00-3

Safety notice SAFETY
5. Keep all tools in good condition and learn the correct way to
use them.
6. Decide a place in the repair workshop to keep tools and re-

moved parts. Always keep the tools and parts in their correct
places. Always keep the work area clean and make sure
that there is no dirt or oil on the floor. Never smoke while
working. Smoke only in the areas provided for smoking.
Preparations for work

1. Before adding oil or making any repairs, park the machine
on hard, level ground, and block the wheels or tracks to pre-
vent the machine from moving.
2. Before starting work, lower blade, ripper, bucket or any other

work equipment to the ground and install the safety bar on
the frame. If this is not possible, insert the safety pin or use
blocks to prevent the work equipment from falling. In addi-
tion, be sure to lock all the control levers and hang warning
signs on them.
3. When disassembling or assembling, support the machine

with blocks, jacks or stands before starting work.
4. Remove all mud and oil from the steps or other places used
to get on and off the machine. Always use the handrails, lad-
ders or steps when getting on or off the machine. Never
jump on or off the machine. If it is impossible to use the
handrails, ladders or steps, use a stand to provide safe foot-
ing.
Tipping up the driver's cab
1. Park the machine on solid, level ground.
2. Lower the work unit to the ground and switch off the engine.
3. Close the cab door.
4. Use the locking bolt to secure the articulated steering (cross-

reference "Securing the articulated steering", Page 2-21).
The machine has to be positioned straight and the articu-

lated steering has to be secured with the locking bolt! If the
driver's cab is tipped up while the machine is bent, the front
frame can cause damage to the windscreen!
5. Open the bonnet.
6. Remove 3 cover fastening screws on each side of the

machine (see arrows).
7. Remove the cover.
00-4 WA90-5 / WA100M-5

8. Remove the cab fastening screws under the rear wheel

cover (arrow).
1
2 screws on the left and 2 screws on the right (1).
9. Take the hand pump lever out of its holder on the radiator (2)
and insert it into the receptacle of the pump (3).
10. Set the lever at the pump to "pump up" and pump the cab
upward until it reaches the limit stop.
WA90-5 / WA100M-5 00-5

11. Move the safety rod on the right side upward until it reaches
the pin at the cab floor.
12. Set the lever at the pump to "pump down" and pump the cab
downward until the safety rod is secure against the right side
of the cab floor.
13. Take the lever out of the pump.
Tipping down the driver's cab

1. Insert the lever into the pump. Set the lever at the pump to
"pump up" and pump the cab upward until it reaches the limit
stop.
00-6 WA90-5 / WA100M-5

2. Fold down the safety rod on the right side and fasten it in this
position (arrow).
3. Set the lever to "pump down" and pump the cab downward
until the cylinder is entirely retracted (the resistance at the
lever increases markedly).
NOTE
Make sure that the guide pin (arrow) on the left of the rear
frame is inserted into the guide bushing of the cab.
4. Screw in the fastening screws for the cab (2 left, 2 right) and
tighten the screws.
Torque = 230 Nm.
WA90-5 / WA100M-5 00-7

5. Remove the lever from the pump and fasten it to the radia-
tor.
6. Reattach the cover.
7. Screw in 3 cover fastening screws on each side of the

machine (see arrows) and tighten the screws.
Torque = 25 Nm
8. Close the bonnet.
Tipping up the driver's cab (option with electric actuator)
1. Park the machine on solid, level ground.
2. Lower the work unit to the ground and switch off the engine.
3. Close the cab door.
4. Use the locking bolt to secure the articulated steering (cross-

reference "Securing the articulated steering", Page 2-21).
The machine has to be positioned straight and the articu-

lated steering has to be secured with the locking bolt! If the
driver's cab is tipped up while the machine is bent, the front
frame can cause damage to the windscreen!
5. Open the bonnet.
6. Remove 3 cover fastening screws on each side of the

machine (see arrows).
7. Remove the cover.
00-8 WA90-5 / WA100M-5

8. On both sides, remove the safety pins (1) and the fastening
screws (2) for the cab.
2 1
1
9. Press the "On" (3) and "Lift" (4) buttons simultaneously, until
the cab reaches the upper limit stop.
3
4
G0090003
10. The top final position has been reached if the slipping clutch
of the electric actuator (6) is activated, with a clearly audible
sound.
11. Move the safety rod (7) on the right side upward until it
reaches the cylinder linkage. 7 7
WA90-5 / WA100M-5 00-9

12. Press the "On" (3) and "Lower" (5) buttons simultaneously,
until the safety rod is secure against the cab floor.
3
4
5
G0090003
Tipping down the driver's cab (option with electric actuator)

1. Press the "On" (3) and "Lift" (4) buttons simultaneously, until
the cab reaches the upper limit stop. Remove the safety rod.
2. Fold down the safety rod on the right side and fasten it in this
position (arrow).
3. Press the "On" (3) and "Lower" (5) buttons simultaneously,

until the cab reaches the lower limit stop. The
"Retracted" position has been reached if the slipping clutch
of the electric actuator (6) is activated, with a clearly audible
sound.
3 G0090003
00-10 WA90-5 / WA100M-5

4. Screw in the fastening screws (2) for the cab (1 left, 1 right),
tighten them and secure them with the safety pins (1).
Torque = 300 Nm.
2 1
1
5. Reattach the cover.
6. Screw in 3 cover fastening screws on each side of the

machine (see arrows) and tighten the screws.
Torque = 25 Nm
7. Close the bonnet.
Precautions during work

1. When measuring hydraulic pressure, check that the measur-
ing tool is correctly assembled before taking any measure-
ments.
2. When removing the oil filler cap, drain plug or hydraulic

pressure measuring plugs, loosen them slowly to prevent
the oil from spurting out.
Before disconnecting or removing components of the oil,
water or air circuits, first remove the pressure completely
from the circuit.
3. The water and oil in the circuits are hot when the engine is
stopped, so be careful not to get burned.
Wait for the oil and water to cool before carrying out any
work on the oil or water circuits.
4. Before starting work, remove the leads from the battery. Al-
ways remove the lead from the negative (-) terminal first.
5. When raising heavy components, use a hoist or crane.

Check that the wire rope, chains and hooks are free from
damage.
Always use lifting equipment which has ample capacity.
Install the lifting equipment at the correct places. Use a hoist
or crane and operate slowly to prevent the component from
hitting any other part.
Do not work with any part still raised by the hoist or crane.
6. When removing covers which are under internal pressure or

under pressure from a spring, always leave two bolts in posi-
tion on opposite sides. Slowly release the pressure, then
slowly loosen the bolts to remove.
7. When removing components, be careful not to break or

damage the wiring. Damaged wiring may cause electrical
fires.
WA90-5 / WA100M-5 00-11

8. When removing piping, stop the fuel or oil from spilling out. If
any fuel or oil drips onto the floor, wipe it up immediately. Fu-
el or oil on the floor can cause you to slip, or can even start
fires.
9. As a general rule, do not use gasoline to wash parts. In par-

ticular, use only the minimum of gasoline when washing
electrical parts. Do not smoke!
10. Be sure to assemble all parts again in their original places.
Replace any damaged parts with new parts.
When installing hoses and wires, be sure that they will not
be damaged by contact with other parts when the machine
is being operated.
11. When installing high pressure hoses, make sure that they
are not twisted.
Damaged tubes are dangerous, so be extremely careful

when installing tubes for high pressure circuits. Also, check
that connecting parts are correctly installed.
12. When aligning two holes, never insert your fingers or hand.
Be careful not to get your fingers caught in a hole.
13. When assembling or installing parts, always use the speci-

fied tightening torques. When installing protective parts such
as guards, or parts which vibrate violently or rotate at high
speed, be particularly careful to check that they are installed
correctly.
Hydraulic system
Only qualified personnel with experience in the handling of high-
ly pressurized fluids is allowed to maintain and repair the hy-
draulic system.
• Hydraulic oil is hot and under high pressure!

Danger of injury to unprotected parts of the body! Always
wear special safety equipment, especially safety googles
and gloves.
• Hydraulic oil is a hazardous substance!
Danger of injury. Seek medical help immediately if you are
exposed to hydraulic oil.
00-12 WA90-5 / WA100M-5

SAFETY Foreword
Foreword
General
This shop manual has been prepared as an aid to improve the
quality of repairs by giving the service personnel an accurate un-
derstanding of the product and by showing them the correct way
to perform repairs and make judgements. Make sure you under-
stand the contents of this manual and use it to full effect at every
opportunity.
This shop manual mainly contains the necessary technical infor-

mation for operations performed in a service workshop. For
ease of understanding, the manual is divided into the following
chapters; these chapters are further divided into the each main
group of components:
Structure and function

This section explains the structure and function of each compo-
nent. It serves not only to give an understanding of the structure,
but also serves as reference material for troubleshooting.
Testing and adjusting

This section explains checks to be made before and after per-
forming repairs, as well as adjustments to be made at comple-
tion of the checks and repairs. Troubleshooting charts
correlating "Problems" to "Causes" are also included in this sec-
tion.
Disassembly and assembly

This section explains the order to be followed when removing,
installing, disassembling or assembling each component, as well
as precautions to be taken for these operations.
Maintenance standard
This section gives the judgement standards when inspecting dis-
assembled parts.
NOTE
The specifications contained in this shop manual are subject to
change at any time and without any advance notice. Use the
specifications given in the book with the latest date.
WA90-5 / WA100M-5 00-13

How to read the shop manual SAFETY
How to read the shop manual
Volumes
Shop manuals are issued as a guide to carrying out repairs.
Distribution and updating

Any additions, amendments or other changes will be sent to Ko-
matsu distributors.
Get the most up-to-date information before you start any work.
Filing method
1. See the page number on the bottom of the page. File the
pages in correct order.
2. Following examples show how to read the page number.
Example 1 (Chassis volume):
10 - 3
Item number (10. Structure and Function)
Consecutive page number for each item
3. Additional pages: Additional pages are indicated by a point

(.) and number after the page number. File as in the exam-
ple.
Example:
10-4
10-4.1
Added Pages
10-4.2
10-5
00-14 WA90-5 / WA100M-5

SAFETY How to read the shop manual
Symbols
So that the shop manual can be of ample practical use, impor-
tant safety and quality portions are marked with the following
symbols:
Symbol Item Remarks
 Safety Special safety precautions are necessary when performing the work.
Caution
Special technical precautions or other precautions for preserving standards are necessary
when performing the work.
Weight of parts of systems.

Weight
4 Caution necessary when selecting hoisting wire, or when working posture is important, etc.
3 Tightening torque Places that require special attention for the tightening torque during assembly.
2 Coat Places to be coated with adhesives and libricants, etc.
Oil, water Places where oil, water or fuel must be added, and the capacity.
5
Drain Places where oil or water must be drained, and quantity to be drained.
6
WA90-5 / WA100M-5 00-15

Hoisting instructions SAFETY
Hoisting instructions
Heavy parts (25kg or more) must be lifted with a

hoist, etc. In the DISASSEMBLY AND ASSEMBLY
section, every part weigthing 25 kg or more is in-
dicated clearly with the symbol: 4
If a part cannot be smoothly removed from the machine by hoist-

ing, the following checks should be made:
1. Check for removal of all bolts fastening the part to the rela-
tive parts.
2. Check for existence of another part causing interference

with the part to be removed.
Wire ropes
1. Use adequate ropes depending on the weight of parts to be
hoisted, refering to the table below:
• The allowable load in tons, is given by vertical tensible

force.
• The allowable load value is estimated to be one-sixth or

one-seventh of the breaking strength of the rope used.
Wire ropes:
(Standard "Z" or "S" twist ropes without galvanizing)
Rope diameter (mm) Allowable load (tons)
10 1.0
11.2 1.4
12.5 1.6
14 2.2
16 2.8
18 3.6
20 4.4
22.4 5.6
30 10.0
40 18.0
50 28.0
60 40.0
00-16 WA90-5 / WA100M-5

SAFETY Hoisting instructions
2. Sling wire ropes from the middle portion of the hook.
Slinging near the edge of the hook may cause the rope to
slip off the hook during hoisting, and a serious accident can
result. Hooks have maximum strength at the middle portion.
100% 88% 79% 71% 41%
3. Do not sling a heavy load with one rope alone, but sling with
two or more ropes symmetrically wound onto the load.
Slinging with one rope may cause turning of the load during
hoisting, untwisting of the rope, or slipping of the rope from
its original winding position on the load, which can result in
a dangerous accident.
4. Do not sling a heavy load with ropes forming a wide hanging

angle from the hook.
When hoisting a load with two or more ropes, the force sub-
jected to each rope will increase with the hanging angles.
The table below shows the variation of allowable load (kg)

when hoisting is made with two ropes, each of which is al-
lowed to sling up to 1000 kg vertically, at various hanging
angles.
When two ropes sling a load vertically, up to 2000 kg of total

weight can be suspended. This weight becomes 1000 kg
when two ropes make a 120° hanging angle. On the other
hand, two ropes are subjected to an excessive force as
large as 4000 kg if they sling a 2000 kg load at a lifting angle
of 150°.
α
kg
(kg)
2000
(kg)
1900
1700
2000
capacity
Capacity
1400
(kg)
1000
Gewicht
1000
Load
500
Load
300 600 900 1200 1500

Lifting
Lifting angle
(°) (°) (α)
Angle
Hebewinkel
WA90-5 / WA100M-5 00-17

Hoisting instructions SAFETY
00-18 WA90-5 / WA100M-5

01 GENERAL
Dimensions, weights and operating data WA90-5 ........................................................................... 01-3
Specifications WA90-5 ..................................................................................................................... 01-4
Weight table WA90-5 ....................................................................................................................... 01-5
Dimensions, weights and operating data WA100M-5 ...................................................................... 01-6
Specifications WA100M-5 ................................................................................................................ 01-7
Weight table WA100M-5 .................................................................................................................. 01-8
Lubricants and operating mediums: WA90-5 ................................................................................. 01-10
Lubricants and operating mediums: WA100M-5 ............................................................................ 01-11
Basic procedures of maintenance .................................................................................................. 01-12
Oil .............................................................................................................................................................. 01-12
Fuel ........................................................................................................................................................... 01-12
Coolant ...................................................................................................................................................... 01-13
Grease ...................................................................................................................................................... 01-13
Storing oil and fuel .................................................................................................................................... 01-13
Filters ........................................................................................................................................................ 01-14
Biodegradable hydraulic oils and lubricants .............................................................................................. 01-14
Outline of electric system .......................................................................................................................... 01-14
Torque list – screws and nuts ........................................................................................................ 01-15
WA90-5 / WA100M-5 01-1

GENERAL
Blank for technical reason
01-2 WA90-5 / WA100M-5

GENERAL Dimensions, weights and operating data WA90-5
Dimensions, weights and operating data WA90-5
Dimensions, weights and operating data

Bucket capacity to ISO 7546 m³ 1,05
Material density t/m³ 1,8
Static tipping load, straight kg 4640
Static tipping load, 40° angle kg 3960
Working load kg 2400
Breakout force, hydraulic kN 63,5
Lifting capacity, hydraulic, on ground kN 59,8
Operating weight kg 6380
Turning radius over bucket mm 4290
L Bucket length in transport position mm 5560 with teeth 5645
A Bucket length during planing mm 5590 with teeth 5730
T1 Width with bucket mm 2050
T2 Width without bucket (above wheels) mm 1990
G Height, including ROPS mm 2800
D Track mm 1590
405/70 R20 SPT9 tyres
B Width over tyres mm 2300
H Distance articulated steer. - front axle mm 1100
Ground clearance, axle /transfer gear mm 350
E
ground clearance, drive shaft mm 460
F Centre of gravity, height above axle centre mm
CTW = additional counterweight
I Centre of gravity, distance to front axle mm
WA90-5 / WA100M-5 01-3

Specifications WA90-5 GENERAL
Specifications WA90-5
Machine model WA90-5
Serial No. 50051 and up
Model S4D95LE-3
Type 4-cycle Diesel, turbo charged
No. of cylinders - bore/stroke [mm] 4 - 95 / 115
Piston displacement [cm³] 3261

Engine
Flywheel horsepower [kW {hp} (PS) / rpm] 55 {73.8} (74.8) / 2350
Maximum torque [Nm / rpm] 255 / 1600
Starting motor 12V - 2.2 kW
Alternator 12V - 60 A
Battery 12V - 92 Ah
Reduction gear 1-stage

Power train
Differential Limited slip differential, locking value 25% or locking value 100%
Drive type Front-, rear-wheel drive

Axle, wheel
Tire 405/70 R20 SPT9
Turning radius over bucket [mm] 4290
Service brake Disc brake outside on the front axle (acting on all 4 wheels by transfer over the drive
shaft)
Brakes
Parking brake Disc brake outside on the front axle (acting on all 4 wheels by transfer over the drive
shaft)
01-4 WA90-5 / WA100M-5

GENERAL Weight table WA90-5
Weight table WA90-5
This weight table is a guide for use when transporting or

handling components.
Components Weight [kg] Components Weight [kg]
Engine 246 Bucket cylinder 51
Radiator 35 Engine hood 100
Drive shaft 22 Front frame 555
Front axle 312 Rear frame 650
Rear axle with transfer box 310 Quick-coupler 135
Wheel 110 Bellcrank 85
Variable-displacement motor 20 km/h 47

Boom (including bushing) 360
Variable-displacement pump 20 km/h 39

Counterweight 1090
Steering cylinder 12.4 Cabine 475
Lift cylinder, each 32.3 Operator seat 32
WA90-5 / WA100M-5 01-5

Dimensions, weights and operating data WA100M-5 GENERAL
Dimensions, weights and operating data WA100M-5
Dimensions, weights and operating data

Bucket capacity to ISO 7546 m³ 1,2
Material density t/m³ 1,8
Static tipping load, straight kg 5530
Static tipping load, 40° angle kg 4680
Working load without CTW kg 2900
Working load with CTW kg 3100
Breakout force, hydraulic kN 66,1
Lifting capacity, hydraulic, on ground kN 66,1
Operating weight kg 6760
Turning radius over bucket mm 4570
L Bucket length in transport position mm 5715 with teeth 5645
A Bucket length during planing mm 5775 with teeth 5730
T1 Width with bucket mm 2200
T2 Width without bucket (above wheels) mm 2090
G Height, including ROPS mm 2850
D Track mm 1635
405/70 R20 SPT9 tyres
B Width over tyres mm 2400
H Distance articulated steer. - front axle mm 1200
Ground clearance, axle /transfer gear mm 380
E
ground clearance, drive shaft mm 510
F Centre of gravity, height above axle centre mm CTW = additional counterweight
01-6 WA90-5 / WA100M-5

GENERAL Specifications WA100M-5
Specifications WA100M-5
Machine model WA100M-5
Serial No. 50051 and up
Model S4D95LE-3
Type 4-cycle Diesel, turbo charged
No. of cylinders - bore/stroke [mm] 4 - 95 / 115
Piston displacement [cm³] 3261

Engine
Flywheel horsepower [kW {hp} (PS) / rpm] 61.5 {82.5} (83.6) / 2350
Maximum torque [Nm / rpm] 291 / 1600
Starting motor 12V - 2.2 kW
Alternator 12V - 60 A
Battery 12V - 92 Ah
Reduction gear 1-stage

Power train
Differential Limited slip differential, locking value 25% or locking value 100%
Drive type Front-, rear-wheel drive

Axle, wheel
Tire 455/70 R20 SPT9
Turning radius over bucket [mm] 4570
Service brake Disc brake outside on the front axle (acting on all 4 wheels by transfer over the drive
shaft)
Brakes
Parking brake Disc brake outside on the front axle (acting on all 4 wheels by transfer over the drive
shaft)
WA90-5 / WA100M-5 01-7

Weight table WA100M-5 GENERAL
Weight table WA100M-5
This weight table is a guide for use when transporting or

handling components.
Components Weight [kg] Components Weight [kg]
Engine 246 Bucket cylinder 53.7
Radiator 35 Engine hood 100
Drive shaft 22 Front frame 540
Front axle 345 Rear frame 650
Rear axle with transfer box 345 Quick-coupler 135
Wheel 120 Bellcrank 84

Boom (including bushing) 373

Counterweight 1275
Steering cylinder 12.4 Cabine 475
Lift cylinder, each 32.9 Operator seat 32
01-8 WA90-5 / WA100M-5

GENERAL Weight table WA100M-5
WA90-5 / WA100M-5 01-9

Lubricants and operating mediums: WA90-5 GENERAL
Lubricants and operating mediums: WA90-5

Lubricants, fuels and filling capacities
WA90-5 Approx. filling

Temperature Viscosity
Lubricants, fuel etc. BI code **) Quality grades capacity in
ranges ranges
litres
ACEA E5
EO 1540 A
or, if not available: -15°C to 45°C SAE 15W-40 1) 10
Engine Engine Oil EO EO 1030 A API CE oder -20°C to 30°C SAE 10W-30 (9,5) *
NRS -15°C to 20°C SAE 5W-30
API CF-4 2)
AGIP ROTRA MULTI THT API-GL4 SAE 80 1)
ESSO TORQUE FLUID 56 API-GL4 SAE 80
MOBILFLUID 424 API-GL4 SAE 80
Transfer Gear Box
MOBILLUBE D LS 80W-90 GO 80 API GL-5 – 1,3
SAE 80W-90
SHELL SPIRAX LS API-GL4 SAE 80W-90
ESSO TORQUE FLUID 62 API-GL4 SAE 10W-30
ESSO TORQUE FLUID 56 API-GL4 SAE 80 Planet Gear:
Front Axle
MOBILLUBE D LS 80W-90 GO 80 API GL-5 – 2 x 0.6
SAE 80W-90
SHELL SPIRAX LS API-GL4 Differential: 8.0
SAE 80W-90
Rear Axle
MOBILLUBE D LS 80W-90
GO 80 API GL-5 – 2 x 1.3
SAE 80W-90
SAE 80W-90
HYD 0530
HVLP
-15° to 20°C ISO VG 46 1)
Hydraulic Oil HYD HYD 1030 -20° to 30°C ISO VG 68
HVLP D
HYD 1540 -15° to 45°C ISO VG 100
ACEA E5
or, if not available: -15° to 45°C SAE 15W-40
Hydraulic system, EO 1540 A 75
steering
or Engine Oil EO
API CE or -20° to 30°C SAE 10W-30 (50) *
EO 1030 A
-15° to 45°C SAE 5W-30
API CF-4 2)
HEES
or BIO-oil BIO-E-HYD 0530 (acc. to VDMA fluid -15° to 20°C ISO VG 46
technology)
Service Brake AGIP LHM Super HYD – – – 1,0
Proportion of Mixture:
Cooling system Antifreeze and 13
Long-Time Coolant SP-C 50% Coolant : 50% Water
Corrosion Protection (10) *
Min. Freeze Proofing: -34° C
CFPP Class B to 0°C
CFPP Class D to -10°C
Fuel tank Diesel fuel ³) DIN-EN 590 – 110
CFPP Class E to -15°C
CFPP Class F to -20°C
Multi-purpose grease MPG
Grease nipples MPG-A KP 2N-20 – NLGI 2 ---
on a lithium base
R134a (CFC-free) 1200 g
Coolant NRS
Air conditioning PAG (polyalkyleneg- - - 180 cm³
Refrigerating machine oil NRS
lycol)
The specified filling capacities are approximate guidelines; test specifications are binding. The selection of the viscosity class depends on the
predominantly existing outside temperature. The temperature limits are to be regarded as guidelines which can be exceeded up or down for a brief
period.
*) Topping-up quantity
1) Works filling
²) If no engine oil of the API CE or API CF-4 specification is available, API CC or API CD-classified engine oil can be used alternatively. The oil change
intervals must be split in half in this case, however.
³) If the fuel sulphur content is between 0.5 and 1.0 %, the oil change interval must be 1/2 normal. With a sulphur content of more than 1.0 %, the oil
change interval must be 1/4 normal.
**) BI codes are the "standard lubricants" for construction machinery and vehicles of the Hauptverband der Deutschen Bauindustrie e.V. (BI). The
brochure "Regelschmierstoffe für Baumaschinen- und Fahrzeuge" (Standard Lubricants for Construction Machinery and Vehicles" can be obtained
from bookstores or Bauverlag GmbH, Wiesbaden and Berlin, under the ISBN no. 3-7625-3102-1."
01-10 WA90-5 / WA100M-5

GENERAL Lubricants and operating mediums: WA100M-5
Lubricants and operating mediums: WA100M-5

Lubricants, fuels and filling capacities
WA100M-5 Approx. filling

Temperature
Lubricants, fuel etc. BI code **) Quality grades Viscosity ranges capacity in
ranges
litres
ACEA E5
EO 1540 A
or, if not available: -15°C to 45°C SAE 15W-40 1) 10
Engine Engine Oil EO EO 1030 A API CE oder -20°C to 30°C SAE 10W-30 (9,5) *
NRS -15°C to 20°C SAE 5W-30
API CF-4 2)
ESSO TORQUE FLUID 56 API-GL4 SAE 80
Transfer Gear Box
MOBILLUBE D LS 80W-90 GO 80 API GL-5 – 1.3
SAE 80W-90
SHELL SPIRAX LS API-GL4 SAE 80W-90
Front Axle
MOBILLUBE D LS 80W-90 GO 80 API GL-5 – 2 x 1.3
SAE 80W-90
SAE 80W-90
Rear Axle
MOBILLUBE D LS 80W-90
GO 80 API GL-5 – 2 x 1.3
SAE 80W-90
SAE 80W-90
HYD 0530
HVLP
-15° to 20°C ISO VG 46 1)
Hydraulic Oil HYD HYD 1030 -20° to 30°C ISO VG 68
HVLP D
HYD 1540 -15° to 45°C ISO VG 100
ACEA E5
or, if not available: -15° to 45°C SAE 15W-40
Hydraulic system, EO 1540 A 75
steering
or Engine Oil EO
API CE or -20° to 30°C SAE 10W-30 (50) *
EO 1030 A
-15° to 45°C SAE 5W-30
API CF-4 2)
HEES
or BIO-oil BIO-E-HYD 0530 (acc. to VDMA fluid -15° to 20°C ISO VG 46
technology)
Service Brake AGIP LHM Super HYD – – – 1,0
Antifreeze and Proportion of Mixture:

Cooling system 13
Long-Time Coolant SP-C Corrosion Protec- 50% Coolant : 50% Water
(10) *
tion Min. Freeze Proofing: -34° C
CFPP Class B to 0°C
CFPP Class D to -10°C
Fuel tank Diesel fuel ³) DIN-EN 590 – 110
CFPP Class E to -15°C
CFPP Class F to -20°C
Multi-purpose grease MPG
Grease nipples MPG-A KP 2N-20 – NLGI 2 ---
on a lithium base
R134a (CFC-free) 1200 g
Coolant NRS
Air conditioning PAG (polyalkyle- - - 180 cm³
Refrigerating machine oil NRS
neglycol)
The specified filling capacities are approximate guidelines; test specifications are binding. The selection of the viscosity class depends on the
predominantly existing outside temperature. The temperature limits are to be regarded as guidelines which can be exceeded up or down for a brief
period.
*) Topping-up quantity
1) Works filling
²) If no engine oil of the API CE or API CF-4 specification is available, API CC or API CD-classified engine oil can be used alternatively. The oil
change intervals must be split in half in this case, however.
³) If the fuel sulphur content is between 0.5 and 1.0 %, the oil change interval must be 1/2 normal. With a sulphur content of more than 1.0 %, the oil
change interval must be 1/4 normal.
**) BI codes are the "standard lubricants" for construction machinery and vehicles of the Hauptverband der Deutschen Bauindustrie e.V. (BI). The
brochure "Regelschmierstoffe für Baumaschinen- und Fahrzeuge" (Standard Lubricants for Construction Machinery and Vehicles" can be obtained
from bookstores or Bauverlag GmbH, Wiesbaden and Berlin, under the ISBN no. 3-7625-3102-1."
WA90-5 / WA100M-5 01-11

Basic procedures of maintenance GENERAL
Basic procedures of maintenance
Oil
• The oil in the engine and in the hydraulic system is subject to extreme conditions (high temperatures, high
pressures). Therefore, the oil quality will decrease with extended operation.
Always use oils prescribed for the works and temperatures indicated in the operating and maintenance man-
ual. Always observe the prescribed oil change intervals.
• Always handle oils with extreme care so that they are not contaminated.When storing or refilling oil, make
sure that it is not contaminated. The majority of all malfunctions is caused by the penetration of dirt and other
contaminations.
• Never mix oil of different brands or types.
• Always refill the prescribed oil quantity. Too little or excessive oil may cause malfunctions.
• If the oil in the hydraulic system is not clear (milky), water or air is propably introduced into the circuit. In such
cases, call your Komatsu dealer.
• Upon each oil change, the related filter must be replaced as well.
• We recommend to have an oil analysis carried out in regular intervals in order to check the machine condi-
tion. Customers who desire such an oil analysis should contact their Komatsu dealer.
Fuel
• The fuel pump is a precision instrument; if fuel containing water or dirt is used, it cannot work properly.
• Be extremely careful not to let impurities penetrate when storing or adding fuel.
• Always use the fuel specified in the Operation and Maintenance Manual. Fuel may congeal depending on the
temperature (particularly at low temperatures below -15°C), so change to a fue matching this temperature.
• To prevent the moisture in the air from condensing and forming water inside the fuel tank, always fill the fuel
tank after completing the day's work.
• Before starting the engine, or when 10 minutes have passed after adding fuel, drain the sediment and water
from the fuel tank.
• If the engine runs out of fuel, or if the filters have been replaced, it is necessary to bleed the air from the cir-
cuit.
• If the fuel sulphur content is between 0.5 and 1.0%, the oil change interval must be 1/2 normal. If the fuel sul-
phur content is more 1.0%, the oil change interval must be 1/4 normal.
01-12 WA90-5 / WA100M-5

GENERAL Basic procedures of maintenance
Coolant
• River water contains large amounts of calcium and other impurities, so if it is used, scale will stick to the en-
gine and radiator causing a defective heat exchange and overheating.
• Do not use water that is not suitable for drinking.
• When using anti-freeze, always observe the precautions given in the Operation and Maintenance Manual.
• Komatsu machines are supplied with Komatsu original anti-freeze in the coolant when the machine is
shipped. This anti-freeze prevents corrosion in the cooling system. The anti-freeze can be used continuously
for two years or 4000 hours. Therefore, it can be used as it is even in hot areas.
• Anti- freeze is flammable, so be extremely careful not to expose it to open flame or fire.
• The proportion of anti-freeze to water differs according to the ambient temperature. For details of the mixing
ratios, see Operation Manual: CLEANING THE INSIDE OF THE COOLING SYSTEM".
• If the engine overheats, wait for the engine to cool before adding coolant.
• If the coolant level is low, it will cause overheating and corrosion due to the air in the coolant.
Grease
• Grease is used to prevent twisting and noise at the joints.
• The nipples not included in the maintenance section are nipples for overhaul, so they need not be lubricated.
If any part becomes stiff after being used for a long time, add grease.
• Always wipe off all of the old grease that is pushed out when greasing. Be particularly careful to wipe off the
old grease in places where sand or dirt in the grease would cause the rotating parts to wear.
Storing oil and fuel

• Keep oil and fuel indoors to prevent any water, dirt or other impurities from penetrating.
• When keeping barrels for a long period, lay down the barrel on its side so that the filler port is at the side (to
prevent moisture from being sucked in).
If barrels have to be stored outside, cover them with a waterproof sheet or take other measures to protect
them.
• To prevent any change in quality during long term storage, be sure to use in the order of 'first in - first out'
(use the oldest oil or fuel first).
WA90-5 / WA100M-5 01-13

Basic procedures of maintenance GENERAL
Filters
• Filters are extremely important safety parts. They prevent impurities in the fuel and air circuits from entering
important equipment and causing problems.
Replace all filters periodically. For details, see the Operation and Maintenance Manual.
However, when working under severe conditions, it is necessary to consider replacing the filters at shorter in-
tervals according to the oil and fuel (sulfur content) being used.
• Never try to clean the filters (cartridge type) and use them again. Always replace with new filters.
• When replacing oil filters, check if any metal particles are stuck to the old filter. If any metal particles are
found, please contact your Komatsu distributor.
• Do not open packs of spare filters until just before they are to be used.
• Always use original Komatsu filters.
Biodegradable hydraulic oils and lubri-

cants
• The use of biodegradable hydraulic oils and lubricants – on the basis of synthetic esters – for Komatsu ma-
chines is permitted. For information on the products cleared for use and best suited for your application con-
tact our authorized service workshops.
Outline of electric system

• If the wiring gets wet or the insulation is damaged, the electric system leaks resulting in hazardous malfunc-
tions of the machine.
• Maintenance work at the electric system includes:

1. Check fan belt tension,
2. Check damage or wear to the fan belt,
3. Check battery fluid level.
• Never remove or disassemble any electric components installed in the machine.
• Never install any electric components other than those specified by Komatsu.
• Be careful to keep the electric system free of water when washing the machine or when it is raining.
• When working on the seashore, carefully clean the electric system to prevent corrosion.
• The optional power source must never be connected to the fuse, starter switch, or battery relay.
01-14 WA90-5 / WA100M-5

GENERAL Torque list – screws and nuts
Torque list – screws and nuts

• Unless otherwise specified, tighten the metric bolts and nuts
to the torque shown in the table.
• The tightening torque is determined by the width across flats

of the nut and bolt.
• If it is necessary to replace any nut or bolt, always use a Ko-

matsu genuine part of the same size as the part that was re-
placed.
NOTE
When tightening panels or other parts having tightening fixtures
made of plastic, be careful not to use excessive tightening torque:
doing so will damage the plastic parts.
Metric Thread – 10.9
Thread diameter Steel Aluminium-Cast

Width across flat [mm]
[mm]
(b) Nm kpm Nm kpm
(a)
M6 10 14 1.4 7.7 0.77
M8 13 35 3.5 19 1.9
M 10 17 (15) 70 7 37 3.7
M 12 19 115 11.5 64 6.4
M 14 22 185 18.5 101.5 10.15
M 16 24 280 28 158 15.8
M 18 27 390 39 218 21.8
M 20 30 560 56 306.5 30.65
M 22 32 750 75 416 41.6
M 24 36 960 96 528.5 52.85
M 27 41 1400 140 774 77.4
M 30 46 1900 190 1053 105.3
M 33 50 2600 260 – –
M 36 55 3300 330 – –
M 39 60 4300 430 – –
WA90-5 / WA100M-5 01-15

Torque list – screws and nuts GENERAL
Metric Fine Thread – 10.9
Thread Diameter [mm] Width across Flat[mm] Steel Aluminium-Cast

(a) (b) Nm kpm Nm kpm
M8×1 13 35 3.5 20 2
M 10 × 1 17 (15) 75 7.5 42 4.2
M 10 × 1,25 17 (15) 70 7 39 3.9
M 12 × 1,25 19 125 12.5 70 7
M 12 × 1,5 19 120 12 67 6.7
M 14 × 1,5 22 200 20 110 11
M 16 × 1,5 24 300 30 167.5 16.75
M 18 × 1,5 27 440 44 243 24.3
M 18 × 2 27 420 42 230 23
M 20 × 1,5 30 620 62 338.5 33.85
M 20 × 2 30 – – 322.5 32.25
M 22 × 1,5 32 820 82 454.5 45.45
M 22 × 2 32 – – 436 43.6
M 24 × 1,5 36 1090 109 596 59.6
M 24 × 2 36 1040 104 573 57.3
M 27 × 2 41 1500 150 832 83.2
M 30 × 2 46 2120 212 1158 115.8
M 33 × 2 50 2800 280 – –
M 36 × 3 55 3500 350 – –
M 39 × 3 60 4600 460 – –
01-16 WA90-5 / WA100M-5

10 STRUCTURE AND FUNCTION
Powertrain ............................................... 10-3 Operation of PPC-valve .................................. 10-41
Servo pressure regulating valve ..................... 10-42
Closed circuit .......................................... 10-4
Emergency Lowering System ......................... 10-42
Hydraulic drive system ........................... 10-5
Main control valve ................................. 10-44
20km/h and 30km/h ........................................... 10-5
WA90-5: Lift cylinder ............................ 10-46
Variable displacement pump ................. 10-6
Regulating valve ................................................ 10-9 WA100M-5: Lift cylinder ....................... 10-47
Charge pressure limiting valve .......................... 10-9 WA90-5: Dump cylinder ........................ 10-48
Control cylinder ............................................... 10-10
4/3 Way valve with direction control solenoids 10-10
WA100M-5: Dump cylinder ................... 10-49
Pressure cut-off valve ..................................... 10-11 Steering cylinder ................................... 10-50
Safety-/charge valve ....................................... 10-11 Loader Linkage with quick-coupler ..... 10-52
Towing ............................................................. 10-12
Quick-coupler ........................................ 10-53
Variable displacement motor ............... 10-13
Monitor display ...................................... 10-54
Drive shaft ............................................. 10-15
Sensors .................................................. 10-55
Axle mounting – front axle ................... 10-16 Engine oil pressure sensor ............................. 10-55
Axle mounting – rear axle .................... 10-16 Fuel level sensor ............................................. 10-56
Front axle ............................................... 10-17 Engine coolant temperature sensor ................ 10-57
With inner disc brake as service brake and Brake oil reservoir sensor ............................... 10-58
outer disc brake as parking brake ................... 10-17 Ribbon heater ........................................ 10-59
Rear axle with transfer box .................. 10-18 Engine stop / start / preheating circuit 10-60
Transfer box TB172 .............................. 10-19 Electrical fuses and relays ................... 10-62
Limited slip differential ......................... 10-20 Fuses .............................................................. 10-62
locking value 25% ........................................... 10-20 Relays ............................................................. 10-63
Engine room ................................................... 10-64
Locking differential ............................... 10-22
locking value 100% ......................................... 10-22 Electrical diagrams ............................... 10-65
Wiring diagram 1/5 - foldout 90-9 ................... 10-65
Wheel hub, front and rear axle ............ 10-24
Wiring diagram 2/5 - foldout 90-11 ................. 10-65
Service brake, front axle ...................... 10-25 Wiring diagram 3/5 - foldout 90-13 ................. 10-65
Parking brake, front axle ...................... 10-26 Wiring diagram 4/5 - foldout 90-15 ................. 10-65
Wiring diagram 5/5 - foldout 90-17 ................. 10-65
Service and parking brake circuit ....... 10-27 Speed control - foldout 90-19 ................. 10-65
Service brake assembly ....................... 10-28 Immobilizer - foldout 90-21 ................. 10-65
Main-brake Valve ................................... 10-29 Air conditioner (option) ........................ 10-66
Steering articulation joint ..................... 10-30 Introduction ..................................................... 10-66
Function .......................................................... 10-67
Steering system .................................... 10-32 Installation of air conditioner ........................... 10-73
Hydraulic circuit diagram of steering system ... 10-32 Safety when handling coolants ....................... 10-74
Priority valve .................................................... 10-34 Operating the air conditioner .......................... 10-76
Orbit-roll-valve ................................................. 10-35 Maintenance of the air conditioner .................. 10-77
Steering relief valve ......................................... 10-36 Instructions for filling ....................................... 10-80
Work equipment hydraulic ................... 10-38 Exchange of magnetic clutch .......................... 10-83
Travel, steering and work hydraulics ............... 10-38 Exchange of compressor ................................ 10-84
Troubleshooting .............................................. 10-86
PPC-Valve .............................................. 10-40
WA90-5 / WA100M-5 10-1

10-2 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Powertrain
Powertrain
1 2 3
Engine:
KOMATSU
S4D95LE-3
n = 2350 min -1
5 4
1 rear axle 2 Hydrostatic transmission

3 Front alxe 4 Displacement pump
5 Displace ment motor
Outline
• The engine power is transmitted to the drive axles through a
hydrostatic system. The system consists of a variable dis-
placement pump mounted on the engine and a variable dis-
placement motor mounted on the rear axle transmission
distribution box. Power is transmitted from the variable dis-
placement motor through the distribution box to the front and
rear axles. The front axle is driven through a prop shaft from
the distribution box.
• Change in the direction driven is achieved by changing the

oil flow direction from the variable displacement pump.
Changing from forward to reverse is done electrically and
can be carried out under power. The force reaction takes
place in the variable displacement drive motor.
• The power transmitted to the front and rear axles passes

through the pinion and crown wheels, through the limited
slip differential to the half shafts.
• The half shafts drive in turn the hub planetary reduction

gears and through the planet carriers the wheels.
WA90-5 / WA100M-5 10-3

Closed circuit STRUCTURE AND FUNCTION
Closed circuit
Outline
Installation step by step
• A hydraulic system is described as closed when the hydrau-
lic fluid is returned from the user direct to the pump.
• There is a high pressure and a low pressure side, depend- a max a max
ing on the direction of load (take-off torque at the user).
a min
• The high pressure side is protected by pressure relief
valves, which unload to the low pressure side. The hydraulic a max motor
fluid remains in the circuit. Only the continuous leakage from pump
pump and motor (dependent on operating data) must be re-
placed. Basic system with variable pump and variable motor.
Single pump input drive direction. Motor power take-
• This fluid is replenished by an integrated auxiliary pump off in both directions. The pump can be swivelled
(normally), which delivers a continuous, adequate supply of smoothly over centre, i.e. the direction of flow is
fluid (boost fluid) via a check valve into the low pressure side reversible.
of the closed circuit. Any surplus flow of the boost pump
which operates in open circuit, is returned via a boost pres-
sure relief valve to the tank. The boosting of the low pres-
DBV
sure side enhances the pump operating characteristics. ∆ Ρmax
Typical features of the closed circuit for axial piston units
DBV
are: ∆ Ρmax
• directional control valves - small sizes for pilot operation
• filter/cooler - small sizes Pressure relief valves - one each for the high and low
pressure sides - prevent the maximum permissible
• tank size - small, dimensioned to suit boost pump flow pressure form being exeeded.
and volume of system
• arrangement/mounting position - flixible/optional
• load maintained via the drive motor
• feedback of braking power

leckage oil
oil tank
The leakage from pump and motor is led back to a

small tank and must be replenished.
boost check
aux- valve
iliary boost
pump pressure
valve
filter
coller
An auxiliary pump for replenishment of leakage oil

and control of the pump. Boost check valve RV. Boost
pressure relief valve DBV. Fitted filter, cooler and
accessories.
10-4 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Hydraulic drive system
Hydraulic drive system
20km/h and 30km/h
1. 4/3 way valve (control valve) 12 18 A6VM107DA

20 km/h
2. Main brake cylinder A6VM160DA
30 km/h
3. Variable displacement pump 16
M1
G
13
4. Variable displacement pump
17
(option GRA)
b
a
T
14
5. Shock valve
X1
X3
6. Control cylinder 15
7. Regulating valve
A
U
B
8. Charge pressure relief valve
9. Pressure cut-off valve
10. Charge pump 22
11. Steering and working

hydraulic pump
12. Shuttle flushing valve 21
P
13. Throttle check valve
T
P
14. Drive range valve
30km/h
20km/h
15. Check valve
16. Control piston
17. Control valve 20
8
1. Range: Energized
32
2. Range: De-energized 11
18. Variable displacement motor

B links
A rechts
19. Suction and return filter M4

Vg=11,6 ccm/U
Vg=19,6 ccm/U
bei 20 km/h
bei 30 km/h
M3 10
Fs
Fe
only 20km/h
20 Fan drive pump

only 30km/h
M1
S
Fa1
9
Fa
M1 Control pressure check point 7

Ps
20km/h
30km/h
8
G
M2 Charge pressure check point

d=1,0
d=1,4
M2
M3 Forward travel hight pressure 5
b
check point
30 km/h
20 km/h
UNTEN
OBEN
Option: GRA
Option: GRA
A4VG56EP
A4VG71EP
M4 Reverse travel hight pressure 4

3 bar
a
check point
a
30 km/h
X2
20 km/h
A4VG56DA
A4VG71DA
Standard:
P1
P2
Standard:
ca. 2,4-4,5bar
6
B2
1 3
bar
2,0
X1
19
b
(18L)
(28L)
A
bar
0,5
Vg=56ccm/U
Vg=71ccm/U
bei 20 km/h
bei 30 km/h
B1
(18L)
(22L)
T1
T2
R
2
2350 U/min
0,35
bar
M
ca. 16 l Air
ca. 42 l Oil
working hydr.
0,03
bar
steering
working hydr.
WA90-5=55KW
WA100M-5=61.5KW
WA90-5 / WA100M-5 10-5

Variable displacement pump STRUCTURE AND FUNCTION
Variable displacement pump
1 2 3 4 5 6
1. Drive shaft
2. Swivel bearing
3. Screw plug
4. Swash plate
5. Adjusting lever, adjusting cylinder-swash plate
6. Screw plug
7. Adjusting cylinder
8. Adjusting screw for mechanical 0-position of wash plate
9. 4/3 way valve with electric forward reverse direction prese-
lection
7 8 9
10-6 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Variable displacement pump
10 11 12 13
10. Hydraulic travel pressure cut-off valve

11. Orifice
12. Safety-/charge valve
13. Regulating valve
14. Charge pressure relief valve
12 14
15. Charge pump
WA90-5 / WA100M-5 10-7

1. Drive shaft
2. Pistons
3. Piston area
4. Piston displacement
5. Swash plate
6. Operating angle
7. Cylinder head
8. Drive shaft
9. Control plate
10. Top dead centre
11. Bottom dead centre
12. Inlet port (rotation as shown)
13. Outlet port (rotation as shown)
Function
• The swash plate drive unit is a displacement pump, where
the displacement pistons are mounted axialy parallel to the
drive shaft. They react against the swash plate.
• The drive shaft is rotated by the engine. The drive shaft is

splined to the cylinder head.
The cylinder head rotates with the drive shaft. The pistons
(2) are mounted in the cylinder head. The pistons are
mounted in guide shoes; these glide over the swash plate
and cause an axial displacement in the cylinder head. The
guide shoes are held with spring pressure against the swash
plate.
During rotation the pistons move between bottom dead cen-

tre and top dead centre and back to the start position. In
moving between the dead centres (here the piston changes
its linear direction) the piston completes a stroke. Because
of this oil is sucked in over the inlet port and displaced
through the outlet port. The oil volume displaced depends
on the piston area an length of stroke.
Sucktion takes place when the oil fills the increasing dis-
placement (cylinder). The oil is forced into the cylinder by
feed pump pressure.
The returning piston then forces the oil out of the cylinder
head through the outlet port.
When the swash plate angle changes over the neutral posi-
tion, the pumped direction also changes. Inlet becomes out-
let, outlet becomes inlet.
10-8 WA90-5 / WA100M-5

Regulating valve
1. Spring cup 8
2. Pressure spring
3. Housing 9
4. Nut
5. Ring
10
6. Piston 1
7. Throttle
11
8. Seal nut 2
12
9. Screw
3 Psp
10. Circlip
11. O-ring 4
12. Coller 13
13. Circlip 5
R
14. Regulating cylinder 14
6
15. Circlip Pst
15
P = from pump 7
P
Pst = Control pressure
Psp = Boost pressure
R = Return to tank
Charge pressure limiting valve
1 2 3
1. Valve housing
2. Spring cup Ps p
3. Pressure spring R
4. O-ring
5. Control piston
6. Shim
Psp = Control pressure

R
R = Return to tank
Ps p
4 5 6
WA90-5 / WA100M-5 10-9

Control cylinder
1 2 3 4 5 6
1. O-ring
2. Pressure spring
3. Pressure spring
4. Control cylinder
5. Distance ring
6. Circlip
7. Collet B A
8. Ring, variable
7 8 9 10 1 1
9. Spring cup
10. Spring cup
11. Rod
4/3 Way valve with direction control sole-

noids
1 2 3
1. Grub screw
2. Control piston
3. O-ring
4. Plug connector
5. Pressure spring
6. Spring cup
4 5 6 7 8 9
7. Valve housing
8. Direction control solenoid
9. Plug connector
10-10 WA90-5 / WA100M-5

Pressure cut-off valve
6
1. Seal nut 1
2. Spring cup 7
3. O-ring 2
4. Pressure spring
5. O-ring 3
6. Adjusting screw 8
7. Cap screw
4
8. Control piston Ps t
9
9. Valve bush
10. Piston R
11. Control piston 10
Pb
12. Valve seat
11
Pa = Travel pressure Pa
Pb = Travel pressure 5
12
R = Return oil to tank
Rst = Control pressure
Safety-/charge valve
6
1. Cap screw
7
2. Pressure spring
3. Screw 1
4. Valve stem guide 8
5. Valve cup 9
6. Adjusting screw
7. Seal nut 2 10
8. O-ring
9. Pressure spring, conical 3 11
10. Spring fixing plate 12
11. Backup ring
4
12. O-ring
WA90-5 / WA100M-5 10-11

Towing
Function
• Machines with hydrostatioc drives should only be towed
when a connection is made in the drive pump between the
1
high pressure and low pressure sides. To enable this, the
high pressure safety valves in the pump have a by-pass
function. That means, when screw (1) is turned the valve
tension is released and the oil can flow between the high
pressure and low pressure sides.
Bypass function
• Release the locknut and srew in the screw (1) until the top of
the screw is level with the locknut. 1
• Tighten the locknut.
To prevent damage to the hydrostatic drive system do not

tow faster than 2 km/h or further than 1 km. Because the
feed pump is not working, the system will loose oil.
Care should be taken that the system does not overheat.
After towing screw (1) should be returned to its original position.

The setting of the high pressure control valve is not changed.
Valve Function
• Release the locknut and screw out the screw (1) until the
screw reaches the end of its stroke.
• Tighten the locknut.
NOTE
If the machine has to be towed over a longer distance and with
higher speed the drive shaft has to be removed. The steering joint
must be locked and a crane used to lift the rear axle.
10-12 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Variable displacement motor
Variable displacement motor
1 2 3 4 5 6 7 8 9 10 11 1 2 1 3
1. Output shaft
2. Retaining ring with washer
3. Retaining ring
4. Tapered roller bearing
5. Adjusting shim
6. Tapered roller bearing
7. Cone piston with piston rings, 7 units 14
8. Center pin 15
9. Cylinder 16
10. Adjusting screw for minimum swivel angle (max. speed) 17
11. Control lens 22 21 20 18

12. Control piston cover with throttle check valve (26)
14. Swivel pin clamping screw
15. Swivel pin
23
16. Adjusting shim
18. Adjusting screw for travel change over pressure
(start of swivel angle change) 25
26
19. Control valve solenoid, 12 Volt,
Energized = max. swivel angle = 1st range
De-energized = min. swivel angle = 2nd range
20. Adjusting screw for max. swivel angle (min. speed)
21. Adjusting shim
22. Shaft seal
23. Safety valve
24. Flushing valve 27
25. Check point for travel change over pressure
28
26. Throttle check valve
29
27. Check valve
28. Electrical override valve
19
29. Solenoid for override valve, 12 Volt, energized when travel-
ling forward
WA90-5 / WA100M-5 10-13

Variable displacement motor STRUCTURE AND FUNCTION
1. Drive shaft
2. Pistons
3. Piston area
4. Piston displacement
5. Swash plate
6. Operating angle
7. Cylinder head
8. Control plate
9. Top dead centre
10. Bottom dead centre
11. Inlet port (rotation as shown)
12. Outlet port (rotation as shown)
Function
• The drive motor is the opposite working principle to the drive
pump. In this case oil under pressure is sent to the drive mo-
tor. Oil enters the motor through thje control plate into the
cylinders. Four or five cylinders are in connection through
the kidney shaped inlet port with oil under pressure. The
other cylinders are connected through the kidney shaped
outlet port to the oil return side.
At least one cylinder is closed at the top or bottom dead cen-

tre. The oil pressure forces the piston out, the guide shoes
slide on the swash plate and causes the cylinder head to ro-
tate. The cylinder turns through the action of the nine pis-
tons and so drives the output shaft. The torque required is
dependent on the drive pressure and is transmitted to the
drive shaft through the pistons in the cylinder head. The oil
volume determins the drive speed.
• The drive torque is created directly at the drive shaft from

the pistons in the cylinder head.
• A change in the swing angle is achieved by a radial mov-

ment of the swash plate with the control piston.
• The swash plate in the variable displacement motor has a

small angle in the neutral/ start position. When the 1st drive
speed is selected, the variable displacement motor moves
to a larger swing angle when taking up the drive and stays in
this position.
• When the 2nd drive speed is selected, the swash plate in

the variable displacement motor has a small swing angle
and stays in this position until a drive pressure of 190 - 200
bar is reached. Above this pressure the swash plate moves
to a greater angle and at full drive pressure reaches the larg-
est swing angle.
10-14 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Drive shaft
Drive shaft
1 7 2 7 3 4
5 6 5
1. Front axle 4. Rear axle 7. Tightening screws

2. Drive shaft 5. Universal joint Tightening torque:
3. Distribution box 6. Sliding joint  70 Nm
Description During steering the angle and distance between

the front and rear frames change.
• The power created by the engine is transmitted
through the drive pump, to the drive motor, and The joints compensate these changes and have
then to the distribution box. The power is trans- a damping effect. Because of this the transmis-
mitted from the distribution box (3) directly to the sion components are protected from vibration
rear axle (4) and through the drive shaft (2) to the during work or when driving across country.
front axle (1).
• Besides transmitting torque the drive shaft has a

further use:
The drive shaft is fitted with universal joints (5)

and a sliding joint (6).
WA90-5 / WA100M-5 10-15

Axle mounting – front axle STRUCTURE AND FUNCTION
Axle mounting – front axle
1. Nut
2. Washer
3. U-bracket
Tightening torque:  = 800 Nm
Axle mounting – rear axle
1. Tightening screws (8 units) Tightening torque  560 Nm
10-16 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Front axle
Front axle
With inner disc brake as service brake and

outer disc brake as parking brake
1 2 3 4 5 6 7
11
10 9 8
1. Wheel hub 6 Breather

2. Service brake (inner multiple 7 Bleeding screw for service brake
disc brake)
3. Axle housing 8 Service brake (inner multiple disc brake)
4. Oil filling and level plug 9 Service and parking brake
5 Differential support 10 Parking brake (outer disc brake)
WA90-5 / WA100M-5 10-17

Rear axle with transfer box STRUCTURE AND FUNCTION
Rear axle with transfer box
2
1
1. Breather 5. Transfer box TB172

2. Speed sensor 6. Flange for variable displacement motor
3. Oil control and fill screw 7. Oil control and fill screw
4. Breather 8. Oil drain screw
10-18 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Transfer box TB172
Transfer box TB172

13
12
10 11
9
8
7
5 6
3
4
1
14
15
16
17
24 19 18
20
22 21
23
1. O-ring 13 Seal
2. Flange 14 Bolt
3. Breather 15 Seal
4. Speed sensor 16 Snap ring
5. O-ring 17 Bearing
6. Bearing 18 Output gear
7. Input gear 19 Bearing
8 Bearing 20 Seal
9 Half housing 21 Cover
10 Rear support 22 Shaft
11 O-ring 23 Plug
12 Bushing 24 Half housing
Description
• The variable displacement motor is mounted on the mounting flange (2). The drive torque is transmitted from
the motor to the input gear (7). The torque is then transmitted mechanically to the output gear (18) and the
output shaft (22). The torque is transmitted from the distribution box through the differential to the drive
shafts.
• The transfer box is mounted on the rear axle.
WA90-5 / WA100M-5 10-19

Limited slip differential STRUCTURE AND FUNCTION
Limited slip differential
locking value 25%
2 3 4
1 5
12 8
9
11 10
1. Axle housing 7. Disc pack

2. Differential housing 8. Sun gear
3. Crown wheel 9. Planet gear
4. Locking plate 10. Pin
5. Ring nut 11. Bearing
6. Half shaft 12. Differential support
10-20 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Limited slip differential
Function
• Because of the nature of their work, 4-wheel drive loaders
have to work in places where the road surface is bad.
In such places, if the tires slip, the ability to work is reduced.

The limited slip differential is installed to overcome this prob-
lem.
Operation
• The self locking effect depends on the internal friction of the
differential. It is produced by two multi-disc brakes, which
are arranged symmetrically in the differential cage. With a
conventional differential, one wheel can be stopped or
slowed down without any difficulty when the vehicle is
jacked up when driving.
The other wheel will then revolve correspondingly faster.

With the selflocking differential this process is rendered
more difficult due to the multi-disc brakes, in fact it will be-
come increasingly more difficult with increasing torque.
• The crown wheel (4) is mounted on the differential housing

(1) and transmits the drive torque to the pins (2). The pins
carry the planet gears (3) and transmit the drive torque to
the sun gears (5).
If one drive wheel starts to lose traction with the ground the
planet gears (3) turning on the pins (2) start to rotate around
the sun gears (5). This takes place because the other drive
wheel now turns slower than the wheel that is slipping.
The reaction to this movement acts on the sun gears (5).

These can move axially. This causes pressure to be applied
to the disc pack (6) and the difference in turning speed be-
tween the two drive wheels is limited.
1 2 3 4 5 6
WA90-5 / WA100M-5 10-21

Locking differential STRUCTURE AND FUNCTION
Locking differential
locking value 100%
3 4 5
2 6
13
9
10
12
11
1. Ring nut 7. Half shaft 13. Differential locking

2. Locking plate 8. Sun gear
3. Lock sleeve 9. Planet gear
4. Pin 10. Bevel gear
5. Crown wheel 11. Lock pin
6. Bearing 12. Lock fork
10-22 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Locking differential
Operation
• With a conventional differential, one wheel can be stopped
or slowed down without any difficulty when the vehicle is
jacked up when driving.
The other wheel will then revolve correspondingly faster.

With the lock differential it is not possible due to the 100%-
locking.
• The crown wheel (9) is mounted on the differential case (7)

and transmits the drive torque to the pins (8). The pins carry
the planet gears (10) and transmit the drive torque to the
sun gears (1).
• If one drive wheel starts to lose traction with the ground the
planet gears (10) turning on the pins (8) start to rotate
around the sun gears (1). This takes place because the oth-
er drive wheel now turns slower than the wheel that is slip-
ping.
If the differential lock is actuated by the locking group (4),

the differential case, gearing and axle shafts are locked to-
gether.
A fork (3) pull a sleeve (5) over the differential case (7) with
three lock pins (6). The sleeve (4) pull the lock pins (6) into
three holes in the sun gear (1). Now the differential case (7)
is locked wth the sun gear (1).
This feature maximizes traction to both wheels. The lock po-

sition will also protect against spinout damage to the differ-
ential.
4
2
6 7 8 9 10
WA90-5 / WA100M-5 10-23

Wheel hub, front and rear axle STRUCTURE AND FUNCTION
Wheel hub, front and rear axle

6 5 4 3 2 1
10
11
12
13 14 15 16
1. Axle mouth housing 9. Ring gear carrier

2. Wheel hub carrier 10. Needle roller bearing
3. Ring gear carrier 11. Half shaft
4. Wheel bolt 12. Oil drain plug
5. Planet gear carrier 13. Tapered roller bearing
6. Ring gear 14. Oil seal ring
7. Planet gear 15. Bushing
8. Planet pin 16. Half shaft
10-24 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Service brake, front axle
Service brake, front axle
7 6 5 4 3 2 1
13
12
11
9 10
1. Bleeding screw 8. Piston return kit

2. Axle mouth housing 9. Self adjust kit
3. Wheel hub carrier 10. Brake disk pin
4. Measuring point for brake pressure 11. Dowel pin
5. Quadring 12 Brake disc
6. Brake piston 13 Counterplate
7. Quadring
Service brake
• The service brakes are two multi disc wet type units operat-
ing in the front axle.
Function
• When pressing the brake pedal the inch valve opens and
the servo oil in the variable displacement pump flows to the
tank. At same time the brake master cylinder is operated.
The oil from brake master cylinder flows to brake pistons.
The brake pistons press the pressure plate against the multi
disc. The inner and outer discs are compressed and the
drive shafts are braked.
• When the brake pedal is released the pressure on the pis-

tons will be released. The return springs pull the brake pis-
tons back and the brake is free.
WA90-5 / WA100M-5 10-25

Parking brake, front axle STRUCTURE AND FUNCTION
Parking brake, front axle
1 2 3 4 5 6 7 8 9 10 11
12
13
1. Brake pad 8. Brake piston

2. Brake disk 9. Elastic washers
3. Brake pad 10. Threaded rod
4. Coil spring 11. Elastic washers
5. Adjusting nut 12 Pusher
6. Thrust ball bearing 13 Lever for parking brake
7. Washer
Parking brake
• The parking brake consists of: Hand brake lever,
bowden cable, work lever and linkage lever.
• An electrical switch on the hand brake lever prevents

the machine from being driven when the parking brake
is applied.
Function
• When the hand brake lever is released, the remove
springs returns the brake shoes and in their starting
position. The parking brake is released.
10-26 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Service and parking brake circuit
Service and parking brake circuit
1. Main brake valve

2. Brake oil tank
3. Front axle
16 4. Brake disc
M1
G
5. Lever for mechanical
6 operated parking brake
b
6. Brake
T
7. Inch-brake valve
X1
3
X3
4
A
5
U
B
B links
A rechts
Fs
Fe
S
Fa1
Fa
Ps
20km/h
30km/h
G
d=1,0
d=1,4
UNTEN
OBEN
3 bar
a
X2
P1
P2
ca. 2,4-4,5bar
B2
1
bar
2,0
X1
b
bar
0,5
B1
2
T1
T2
R
7
2350 U/min
0,35
bar
M
ca. 16 l Air
ca. 42 l Oil
working hydr.
0,03
bar
steering
working hydr.
WA90-5=55KW
WA100M-5=61.5KW
WA90-5 / WA100M-5 10-27

Service brake assembly STRUCTURE AND FUNCTION
Service brake assembly
7 6 5 4 3 2 1
13
12
11
9 10
1. Expansion tank 6. Connection to the inch valve in the variable dis-

placement pump
2. Brake light switch 7. Brake master cylinder
3. Bracket for pedal and brake master cylinder 8. Master cylinder push rod
4. Adjusting screw for pedal 9. Service and parking brake
5. Pedal 10. Connection to the service brake
Function
• The inch valve is mounted in the variable displacement
pump. The inch valve is connected to the brake pedal with a
hydraulic hose (6).
• The inch valve allows, independent of engine speed and

driving resistance, a variable speed reduction. When the
inch valve is used, it reduces the servo pressure in the vari-
able displacement drive pump, and the pump moves to-
wards the no-displacement position (neutral). In this position
no oil is pumped. When the pump moves through the neutral
position the direction of the oil flow smoothly changes.
• That means, that when the pump moves towards the neutral
position the drive torque is slowly reduced and the machine
can roll to a stop. At the same time the brake master cylin-
der is activated and brakes the machine.
10-28 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Main-brake Valve
Main-brake Valve
4 5 6
1 Adjusting screw for pedal 5 Bracket for pedal and brake master cylinder
2 Locknut 6 Brake light switch
3 Brake master cylinder 7 Expansion tank
4 Pedal
Function
• The inch valve in the variable displacement pump allows, in-
dependent of engine speed and driving resistance, a vari-
able speed reduction. When the brake pedal is pressed, a
pilot pressure is applicated to the inch valve. It reduces the
servo pressure and the pump moves towards the no-dis-
placement position (neutral). In this position no oil is
pumped. The wheel loader stops. At the same time the
brake master cylinder is activated and brakes the machine.
WA90-5 / WA100M-5 10-29

Steering articulation joint STRUCTURE AND FUNCTION
Steering articulation joint
1. Front frame 8. Bearing 15. Lubricating hole

2. Safety ring 9. Screw, M12x35 16. Pin
3. Pin 10. Pin
4. Needle roller bearing 11. Bushing
5. Seal 12. Dust seal
6. Screw, M24x1.5x80 13. Washer
7. Rear frame 14. Shim, 0.5 or 1.0 mm
Description
• The front frame (1) and the rear frame (7) are connected
through the upper (10) and lower steering articulation joint
(3).
• The steering cylinder is mounted on the left side of the ma-

chine and forms a connection between the front and rear
frames (not shown). The angle between the front and rear
frames (the turning circle) is proportional to the steered an-
gle.
10-30 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Steering articulation joint
WA90-5 / WA100M-5 10-31

Steering system
Hydraulic circuit diagram of steering system
L 2 R
240 bar
3 240 bar
7
4
5
320-160 ccm/U
175 bar
8
P 6 T LS
POS.2
Work-
hydraulic
1 1
POS.1 EF CF
9 LS
32 8
10
11
WA90-5
WA100M-5
10-32 WA90-5 / WA100M-5

Hydraulic circuit diagram of steering system
1. Steering cylinder
2. Shock valve
3. Anti-cavitation valve
4. Steering unit
5. Rotary spool
6. Steering pressure relief valve
7. Valve (only for emergency steering)
8. Check valve
9. Priority valve
10. Hydraulic pump
11. Oil tank
Priority valve port identification
P Inlet from pump

CF Outlet to steering unit
EF Outlet to main control valve
LS Control line from steering unit
Steering unit port identification
P Inlet from priority valve

T Return oil
L Connection to steering cylinder, left side
R Connection to steering cylinder, right side
LS Control line to priority valve
WA90-5 / WA100M-5 10-33

Steering system STRUCTURE AND FUNCTION
Priority valve
Outline
• The priority valve serves to ensure that in a steering opera-
tion oil is supplied to the steering system as a matter of pri-
ority; the residual quantity of oil is fed to the loader hydraulic
system. When no steering takes place, all the oil is passed
to the loader hydraulic system.
1 2 3 4 5 6 7
LS
EF CF
P Inlet from steering and working hydraulics pump

LS Control line inlet from steering unit
CF Outlet to steering unit
EF Outlet to control unit of loader hydraulics
1. Screw fitting
2. Sealing ring
3. Orifice
4. Control piston
5. Sealing ring
6. Spring
7. Spring sleeve with orifice
10-34 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Steering system
Orbit-roll-valve
Outline
• The orbit-roll is connected to the steering wheel through the
steering column. The orbit-roll controls the oil flow from the
steering pump to the steering cylinder and sets the steering
angle. The amount of oil delivered is proportional to the
amount the steering wheel is turned.
• The control spool (4) and the control sleeve (6) form the
steering control valve. In normal working condition the oil
displacement system, made up of rotor (2) and stator (1) op-
erates as a hydraulic pump. In an emergency steering situa- 3
tion the unit operates as a hand pump.
Structure 4
1
• The control spool (4) is directly connected to the steering
wheel column and is connected to the control sleeve (6) by
the centre pin (7) and the centring springs (5). 2 5
The control spool (4) and the control sleeve (6) do not have
contact with each other in the neutral position. 6
• The drive shaft (3) is meshed with the centre pin (7), and
forms one unit with the control sleeve (6). The other end of 7
the drive shaft (3) is meshed with the splines of the rotor (2)
of the girotor.
8
• There are four ports in the valve body (8). They are connect- PR
ed to the steering pump, to the tank and to the steering cyl-
inders. There is a check valve (9) mounted between the TL
pump port and the tank port. If the steering pump or the en-
gine fail, oil for the emergency steering can be drawn for the
girotor through the check valve (9).
In the orbit-roll, between the steering cylinder and the orbit-

roll, are mounted shock valves (10) these prevent damage 9 10
to the system from outside shocks.
WA90-5 / WA100M-5 10-35

Steering system STRUCTURE AND FUNCTION
Steering relief valve
1. Orbit-roll valve
2. Pressure limiting valve
3. Valve seat (spool) 1
4. O-ring
5. Backup ring
6. Pressure spring
7. Distance bush R
P
8. Clamping screw
9. Sealing ring
10. Screw plug L
T
Function
• The steering relief valve (2) is inside the orbit-roll valve (1),
and sets the maximum circuit pressure of the steering circuit 3
when the orbit-roll valve is actuated. When the orbit-roll
valve is being actuated, if the steering circuit goes above the
set pressure of this valve, oil is relieved from this valve. 4
6
2
7
10
10-36 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Steering system
WA90-5 / WA100M-5 10-37

left 13 right
10-38
rechts Cabine
heben senken
220 bar P
11 8
b1 heben (grün) d=1,0 3
320 bar L R
senken (gelb)
a1
Work equipment hydraulic
240 bar 240 bar

B1
d=1,0
A1 1
BOOM
b2 auskippen (rot) 4
320 bar einkippen (blau)
d=0,6 350
a2
B2
12
d=3,5 d=1,0
A2 2
320 bar
9 b3 zu (weiß) 5
auf (braun)
a3
B3
A3 T
18+4 bar 6 P T
320-160 ccm/U
T1
185 bar
0,16 l
11 20 bar
21 14 P T LS
links
heben senken
Work equipment hydraulic
direction
Travel, steering and work hydraulics
BUCKET
10
einkippen auskippen
17 16
ca. 2,4-4,5bar
Z
Fa
15
EF CF
MB
b a a b
B oben M1 A6VM107DA
Ps Fa1 Fe
90m 20 km/h
B left LS
A6VM160DA
P
U 90n 30 km/h
a
M
Standard: Option: GRA
32 8
A4VG56DA A4VG56EP
20 km/h 20 km/h
20 19 Standard:
A4VG71DA
Option: GRA
A4VG71EP
7 A unten
R b
30 km/h 30 km/h
T1
T2 X3 X1 T G
A right
X1 X2 G S
5 Fs
MA
6
d=1,0 P
18
T P
steering
3 bar
working hydr.
2
(28L)
(35L)
B1 A B2
P1 4
pilot valve
3 P2 WA90-5
0,5 2,0
0,03 0,35 bar bar M16x1,5(10L) WA100M-5
bar bar
1
STRUCTURE AND FUNCTION
WA90-5 / WA100M-5
STRUCTURE AND FUNCTION Work equipment hydraulic
Travel, steering and work hydraulics
1. Hydraulic oil tank

2. Check valve
3. Suction and return filter
4. Oil cooler
6. Variable displacement motor
7. Steering and work hydraulic pump
8. PPC-valve
9. Main control valve
10. Tilt cylinder
11. Lift cylinder
12. Steering unit
14. Ball valve for street travel lock
15. Priority valve
16. Inch-brake valve
17. Main brake cylinder
18. 3-way ball valve
19. Bolt cylinder
20. Cylinders on multi purpose equipment
21. Pressure accumulator
WA90-5 / WA100M-5 10-39

PPC-Valve STRUCTURE AND FUNCTION
PPC-Valve
U3
U2
U5
U6
U4
U1
T
P
P
2mm
0.8
mm
0.8
mm
0.8
mm
0.6
mm
U6 U5
U1 U3 U2 U4
15FX 031A
U1. Connection boom lower/float U4. Connection bucket dump

with detent U5. Connection 3rd control unit
U2. Connection bucket tilt back with detent
U3. Connection boom raise U6. Connection 3rd control unit
PPC-valve port identification
P Connection from pump

T Connection to tank
10-40 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION PPC-Valve
Operation of PPC-valve
Function
• The PPC-valve controls the oil comming from the feed
pump. Depending on how the PPC-valve lever is moved, oil
is sent to the servo face of one or other of the main control
valve spools.
The oil pressure acts on this spool face and moves the
spool.
Operation
• With the engine running the operating lever is in the neutral
position. The PPC system is supplied with oil from the vari-
able displacement drive feed pump.
• The P-channel in the pilot control valve is filled with oil by

the supply pump. After the pressure buildup the pilot control
pressure is limited by the supply pressure limitation valve
that is integrated into the variable displacement pump. Sur-
plus oil that is not needed flows back into the return line
through the housing of the variable displacement pump.
The steering and working hydraulic pump supplies oil

through a priority valve to the steering and hydraulic sys-
tems.
If the steering is not used, the complete oil flow is sent to the
working hydraulic system. It flows through the main control
valve to the tank.
All pilot control lines between main and pilot control valve
are connected to the oil return line.
When the PPC is activated pressure builds up in the pilot

control line. The main spool valve is activated by the pres-
sure and the main oil flow is redirected. Because of that the
cylinder function is carried out as long as someone activates
the control lever. When the mechanical stop of the working
cylinder is reached the pressure increases until the pres-
sure-relief valve opens.
• If the PPC control lever is moved through the boom lower

position, that is moved to the end of its stroke, the PPC ser-
vo oil reaches a maximum pressure.
Because of this the boom lower spool is moved to the boom

float position. A short circuit is formed between boom lift and
lower and the outlet to the tank is opened.
The working equipment now follows the ground contours.
WA90-5 / WA100M-5 10-41

PPC-Valve STRUCTURE AND FUNCTION
Servo pressure regulating valve
Function
• The servo pressure regulating valve is in the drive pump.
Apart from limiting the drive system feed pressure it also lim-
its the PPC servo pressure.If the PPC valve is not used the
servo pressure regulating valve protects the PPC and the
drive feed pressure system.
Operation
• The regulating valve is mounted in the end housing of the
variable displacement drive pump. 1 2
When the oil pressure rises above the spring (2) preset P sp
pressure, the valve piston (3) compresses the spring and
the seat lifts. the valve piston moves to the left and the oil R
can release to the tank.
Psp Feed pump oil pressure

R Return to tank
R
P sp
Emergency Lowering System
The machine is provided with a pressure accumulator for the 3 1 4
work hydraulic system. If the engine is not running, you can
lower the work unit with the multi-function lever.
If you have secured the work hydraulic system with the

locking lever of the work hydraulic system, you cannot
lower the work unit.
Make sure that nobody is standing below the work unit.
Press slowly the multi-function lever into position ‘’P’’. The work
unit is lowered.
10-42 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION PPC-Valve
WA90-5 / WA100M-5 10-43

Main control valve STRUCTURE AND FUNCTION
Main control valve
PA1 PA2 PA3
3
1
2
PB2 PB3
PB1
AUX
P T1 T2
BUCKET
1
0 1
2
4
0
2 BOOM
1 1 1
0 0 0
2 2 2
4
220 bar
VS
320 bar 320 bar 320 bar

18 + 4 bar
B1 A1 B2 A2 B3 A3
BOOM BUCKET AUX
1. Data plate .
2. Main relief valve .
3. Shock and anticavitation valve
Main control valve port identification
P Connection from the pump

T2 Connection to the tank
A1 Connection raise, piston side
B1 Connection lower, rod side
A2 Connection dump, rod side
B2 Connection tilt back, piston side
A3 Connection 3rd control unit
B3 Connection 3rd control unit
PA1 - PA3 Connection PPC valve
PB1 - PB3 Connection PPC valve
10-44 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Main control valve
WA90-5 / WA100M-5 10-45

WA90-5: Lift cylinder STRUCTURE AND FUNCTION
WA90-5: Lift cylinder

Dimensions
Closed length 1010 ± 1.5 mm

Stroke 689 ± 1.5 mm
Piston rod ø 50 mm
Piston ø 80 mm
Tightening torque
Gland (3) 350 - 400 Nm

Lock nut (13) 750 - 800 Nm 5
8
Pressures
7
Operating pressure 220 bar 6
Shock pressure 340 bar 9
3
1. Cylinder housing, assy.

2. Piston rod, assy.
3. Gland
4. Piston
5. Wear ring
6. Wiper ring
7. Rod seal
8. O-ring
9. Backring 2
10. O-ring 1
11. Piston seal
12. Wear ring 10
13. Hexagon locknut
11
14. O-ring
12
15. Lock washer
4
15
13
10-46 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION WA100M-5: Lift cylinder
WA100M-5: Lift cylinder

Dimensions

Piston rod ø 50 mm
Piston ø 80 mm
Tightening torque
Gland (3) 350 - 400 Nm

Lock nut (13) 750 - 800 Nm 5
8
Pressures
7
Operating pressure 240 bar 6
Shock pressure 340 bar 9
3
1. Cylionder housing, assy.

3. Gland
4. Piston
5. Wear ring
6. Wiper ring
7. Rod seal
8. O-ring
9. Backring 2
10. O-ring 1
11. Piston seal
12. Wear ring 10
13. Hexagon locknut
11
14. O-ring
12
15. Lock washer
4
15
13
WA90-5 / WA100M-5 10-47

WA90-5: Dump cylinder STRUCTURE AND FUNCTION
WA90-5: Dump cylinder

Dimensions
Closed length 1017 ± 2 mm

Piston rod ø 60 mm
Piston ø 100 mm
Tightening torque
Gland (3) 400 - 450 Nm

Lock nut (13) 1000 -1050 Nm
Pressures
Operating pressure 220 bar

5
Shock pressure 320 bar
10
7
6
1. Cylinder housing, assy. 8
9
3. Gland 3
4. Piston 2
5. Wiper ring 1
6. Wear ring 14
7. Rod seal 11
8. Backring 12
9. O-ring 4
10. O-ring
11. Piston seal 15
12. Wear ring 13

13. Hexagon locknut
14. O-ring
15. Lock washer
10-48 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION WA100M-5: Dump cylinder
WA100M-5: Dump cylinder

Dimensions
Closed length 1135 ± 2 mm

Piston rod ø 60 mm
Piston ø 100 mm
Tightening torque
Gland (3) 400 - 450 Nm

Lock nut (13) 1000 -1050 Nm
Pressures

5
10
7
6
1. Cylinder housing, assy. 8
9
3. Gland 3
4. Piston 2
5. Wiper ring 1
6. Wear ring 14
7. Rod seal 11
8. Backring 12
9. O-ring
4
10. O-ring
11. Piston seal 15
12. Wear ring 13

13. Hexagon locknut
14. O-ring
15. Lock washer
WA90-5 / WA100M-5 10-49

Steering cylinder STRUCTURE AND FUNCTION
Steering cylinder
Dimensions

Piston rod ø 35 mm
Piston ø 60 mm
Tightening torque
Guide bush (4) 300 - 350 Nm

Lock nut (13) 330 - 370 Nm
Pressures 13
14
3
11
12
8
1. Cylinder housing, assy.
2
1
3. Piston
4
4. Gland
5. Bearing
6. Wiper ring 9
7. Rod seal 7
8. O-ring 5
9. Backring 10
6
10. O-ring
11. Wear ring
12. Piston seal
13. Hexagon locknut
14. lock washer
10-50 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Steering cylinder
WA90-5 / WA100M-5 10-51

Loader Linkage with quick-coupler STRUCTURE AND FUNCTION
Loader Linkage with quick-coupler
5
4
1. Boom 4. Quick-coupler
2. Bucket cylinder 5. Link
3. Bellcrank 6. Lift cylinder
10-52 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Quick-coupler
Quick-coupler
9
1
A
8
A
5
7 6
3
4
1. Hose 6. Screw
2. Decal quick-coupler 7. Banjo coupling
3. Plug 8. Clip
4. Dust protection 9. 3-way-cock
5. Block, LH
Function
• The standard machine is equipped with a quick-coupler and
the 3. control circuit for additional device. The locking of ad-
ditional device, for example claw bucket or forklift ensures
by hydraulic.
After assembly of the additional device the hoses will be

connected with the quick-couplers and a manual actuated
switch lever to the 3. control circuit.
• When the oil flows to the additional device, the quick-coupler

is automatically blocked.
WA90-5 / WA100M-5 10-53

Monitor display STRUCTURE AND FUNCTION
Monitor display
Display group Symbol System Operation Display type
Rear windscreen
Display When switched on Display lights up.
heater
When the display lights up the igni-

tion is switched on. Duration
Air intake pre-heater When pre-heater is switched on
depends on the ambient tempera-
ture.
Turning lights
When switched on Display lights up.
(left - right)
Travel direction Display lights up when the forward/

When driving
(forward, reverse) reverse lever is not in NEUTRAL.
Display lights up and an acoustic

When the parking brake is
Parking brake warning is heard if the forward/
applied
reverse lever is not in NEUTRAL.
Headlight When switched on Display lights up.
Speed Range 2 When switched on Display lights up.
Fan reversal When switched on Display lights up.
Shows the current working time in

Counter Working hours Engine working time in hours hours, when the engine generator is
charging.
Display lights up and shows the cur-

Engine water tempera- rent engine working temperature. By
Beam display
ture temperatures over 105°C, there also
is an acoustic warning.
Analogue display
Display lights up and shows the cur-
Fuel level Beam display
rent fuel level.
Display lights up and shows the

Speedometer 2-point display
travel speed.
Display lights up and there is also an

Engine oil pressure Lower than permitted
acoustic warning.
Display lights up when the

Generator Battery is not being charged battery is being charged by the run-
ning engine.
Warning light
When the vacuum in the air filter Display lights up when the filter is
Air filter
is too high too dirty.
Brake oil level When the level is too low Display lights up.
10-54 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Sensors
Sensors
Sensor detection item Sensor method When normal When abnormal
Eng. oil pressure Contact ON OFF
Engine coolant temperature Resistance 25°C (42.7 kΩ) 106°C (3.157 kΩ)
Fuel level Resistance FULL (2.2 kΩ) EMPTY (88.5 kΩ)
Air filter negative pressure Contact OFF ON
Brake oil level Contact OFF ON
Engine oil pressure sensor
1 2 3 4 5 6
1. Plug
2. Contact ring
3. Contact
4. Diaphragm
5. Spring
6. Terminal
Function
• This sensor is installed to the engine block and the dia-
phragm (4) detects the oil pressure. If the pressure goes be-
low the specified pressure, the switch is turned ON.
Structure of circuit
This makes the monitor flash to warn of the abnormality. At
the same time the alarm buzzer is actuated to warn of the
abnormality.
WA90-5 / WA100M-5 10-55

Sensors STRUCTURE AND FUNCTION
Fuel level sensor
1. Connector
2. Guide
3. Tube
4. IFloat
6
5. Bracket 7
6. Upper plate 2
3 4
Function
• The fuel level sensor is mounted and secured with the upper
plate (7) in the top of the tank. The float (4) moves up and
down according to the fuel level.
The tube (3), which is mounted on the float, moves up and

down in the body (3) along a resistance wires (8). The resis-
tance wire (8) gives a resistance proportional to the position
of the float.
The measured resistance is sent to the monitor as an elec-

trical signal and shows the fuel level.
10-56 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Sensors
Engine coolant temperature sensor
1. Connector
2. Plug
3. Thermistor
Function
• This sensor is installed to the engine cylinder block. The
change in the temperature changes the resistance of the
thermistor, and a signal is sent to the monitor to display the
temperature.
When the display on the monitor reaches the specified level,

the caution lamp and alarm buzzer are also actuated at the
same time to warn of the abnormality.
WA90-5 / WA100M-5 10-57

Sensors STRUCTURE AND FUNCTION
Brake oil reservoir sensor
1. Contacts
2. Screw cap
3. Float
4. Brake pipe connection
5. Mounting
Function
• The sender unit is mounted in the screw cap. When the oil
level falls under a minimum the float sinks down until the
switch contacts close (ON position).
This lights the warning lamp to inform the driver that the
brake oil level is low.
Structure of circuit
10-58 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Ribbon heater
Ribbon heater
Function Operation
Electrical ribbon Current supply ON
heater (pin 15)
OFF
Start signal ON
(pin 50a)
OFF
Preheat/warning light ON
OFF
t 30s
Relationship between ambient temperature and preheat time
Preheat time t (s)
30
20
10
0
-25 -20 -15 -10 -5 0 T (°C)
Ambient temperature
If prehater is working pilot lamp is on. After starting the engine at

temperatures below 0°C the preheating continues for 30 sec.
The water coolant temperature influences the temperature

transmitter resistance. The resistance changes according to the
water coolant temperature and sets the electrical current for the
in series connected monitor. The monitor then controls the pre- GK100838
heating time of the ribbon heater.
WA90-5 / WA100M-5 10-59

Engine stop / start / preheating circuit STRUCTURE AND FUNCTION
Engine stop / start / preheating circuit
10-60 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Engine stop / start / preheating circuit
Engine stop/ start/ preheating circuit
Section Description Sect. Description
6 S 43 Start-switch 7 K 106 Relay, battery
8 S 58 Battery, main switch 6 K 158 Relay, starter motor
3 G 10 Alternator 17 K 167.2 Relay, timer 0.8 sec.
8 G 57 Battery 4 K 238 Relay, air preheater engine
6 M9 Starter motor 3 H 28 Control lamp, alternator
3 P 21 Service meter 4 H 76 Control lamp, preheater engine
2 P 426 Main monitor 5 Y 320 Magnet, engine stop
4 R 12 Air preheater engine
Connectors
XL Connector floor frame harness XJ Connector main monitor
XM Connector engine harness XS Connector fuse
Fuses
F Fuse
Engine start Preheating

• Voltage flows in the following circuit: Starting mo- • Current flows to the starter motor (M9) - terminal
tor (M9) - terminal B, battery relay (K106) termi- B, preheat relay (K238) terminal 88a, battery re-
nal 30 and starting switch terminal B. When the lay (K106) and to the starting switch terminal BR.
starting switch is turned (terminal BR) relay
(K106) is activated. Now terminal BR in the ma- • When the starting switch is switched on, terminal
chine is switched on, the engine stop solenoid BR activates the battery relay (K106). Now termi-
(Y320) is activated, the controll circuit for the pre- nal BR in the machine is on, the stop solenoid
heating system is also on. (Y320) and the controll circuit for the preheat
system is activated.
• When the starting key in the starter switch is
turned to position C, current flows to the main • The preheat time depends on the cooling water
monitor. If the forward/reverse lever is in the neu- temperature and is controlled over the main
tral position, current can flow to the starter relays monitor (P426) and the cooling water tempera-
(K158) and the starter is activated through termi- ture sender.
nal S. The engine starts.
• Terminal 10 in connector XJ15 controlls the
Engine stop warning light in the main monitor. When preheat-
ing is concluded the warning light goes off. The
• The starting switch is turned off. Terminal 15 is
engine can be started. Starting before the pre-
now off and the battery relay (K106) is now open,
heating is concluded ends the preheating. In the
the engine stop magnet (Y320) is deactivated
event of temperatures below 0°C, the pilot lamp
and returns to the stop position.
again lights up after the start, for 30 s.
WA90-5 / WA100M-5 10-61

Electrical fuses and relays STRUCTURE AND FUNCTION
Electrical fuses and relays
Fuses
1 2 3
Starter switch, shut off Gear, solenids, work- Solenoids ALS, mag-
1 10 A 1 10 A 1 10 A
solenoid ing hydraulic net oil dedent
Socket (cigarette light-
2 10 A 2 Flashing light 10 A 2 Air condition 25 A
er)
Interior light, radio Radio,, magnet valve,
3 10 A 3 Main monitor 10 A 3 10 A
memory cooler
Hazard warning flush- Rotation beacon,
4 10 A 4 Working light 20 A 4 10 A
er driving light
Position light left, li- Back up alarm, slip
5 Wash/wipe front/rear 20 A 5 10 A 5 10 A
cence light differential
6 Brake light, horn 10 A 6 Position light right 10 A 6 Air suspension seat 10 A
Blower fan, fresh air/ Head light, high Quick coupler,
7 20 A 7 10 A 7 10 A
heater beam sweeper
Central lubrication,
8 Heater, rear window 20 A 8 Head light, low beam 10 A 8 10 A
speed control
10-62 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Electrical fuses and relays
Relays
K 376 K 385
Differential lock Backup alarm K 56.1 Low beam
(option) (option)
K 296
Air condition K 373.1 Parking brake forward K 56.2 High beam
(option)
K 235 Driving range K 373.2 Parking brake reverse K 67 Flasher
KF K 314
Speed control forward K 167 Timer 0.8 sec. Switch frequency ALS
(option) (option)
KR B 335 K 180
Speed control reverse Additional buzzer Blower engine cooler
(option) (option) (option)
WA90-5 / WA100M-5 10-63

Electrical fuses and relays STRUCTURE AND FUNCTION
Engine room
Slow-blow fuses
F4-100A = Battery-relay / Starter motor

F5-250A = IPreheater-relay / Starter motor
Relays
K238 = Relay preheating

K106 = Relaiy battery
K158 = Relay starter motor
10-64 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Electrical diagrams
Electrical diagrams
See section 90 for:
Wiring diagram 1/5 - foldout 90-9
Speed control - foldout 90-19
Immobilizer - foldout 90-21
WA90-5 / WA100M-5 10-65

Air conditioner (option) STRUCTURE AND FUNCTION
Air conditioner (option)
Introduction
The air conditioning systems of our wheel loaders are filled with
the environmentally friendly coolant R134a (tetrafluorethane).
General
• Liquid cooling gas absorbs heat when it turns into gas.
This takes place in the vaporizer.
• When the gas turns into liquid gas the heat is dissipated.
This takes place in the condenser.
• The air conditioner does not produce cold air, it takes the
temperature from the surrounding warm air and dissipates it.
Physical principal
• Physically, heat moves from a warm element towards a cold
element. When this occurs, the fast moving molecules in the
warm element transfer a part of their energy to the slow
moving molecules in the cold element. This causes the fluid
used in the air conditioner to change form. Individual atoms,
which make up the molecules, change their position. When
this happens the fluid changes from gas to liquid.
• e.g.: This reaction can be seen with water. Water is normally

liquid between 0°C and 100°C. If the water is heated, it be-
comes steam. The water changes from a liquid form into a
gas form. If the water is cooled it becomes ice. The water
changes from a liquid form into a solid form.
Physical datas - R134a Characteristics - R134a
Molecular formula – CH2FCF3 • Colourless, odorless, tasteless
Molecular name – 1,1,1,2-Tetraflourethan • Incombustible, so there is no danger of ignition or

Agent class – HFKW explosion
Molecualr weight – 102.03 • Chemically stable
Boiling point (at 1,013 bar) °C -26.5 • Does not decompose structural materials
Critical temperature °C 101.15 • Ozone depletion potential (ODP) of 0
Critical pressure bar 40.64
Critical density kg/l 0.508
ODP (Ozone Depletion Potential) – 0
GWB (Global Warming Potential) – 0.24 – 0.29
10-66 WA90-5 / WA100M-5

STRUCTURE AND FUNCTION Air conditioner (option)
Function
The coolant circuit

• The coolant R134a circulates throughout the system in an
enclosed circuit.
• Gaseous coolant under low pressure is sucked from the va-

porizer (8) by the compressor (2). This places the gaseous
coolant under high pressure (approx. 20 - 30 bar) and for-
wards it to the condenser (3).
The gaseous coolant transcends into a liquid state in the

condenser (3) because of the applied pressure and removal
of heat. Fans blow outside air through the condenser to cool
the warming coolant. The heat removed from the air fed into
the operator's cab is passed on to the outside air. The cool-
ant is still under high pressure at this point.
The coolant passes through the filter dryer (4) and the pres-
sure switch (5) at the entrance to the vaporizer (8) in this
state. The coolant is filtered and dried in the filter dryer (4). It
is also a compensation tank at the same time.
The throttle effect of the expansion valve (7) reduces the

pressure and the temperature of the coolant. It makes sure
that only as much coolant flows into the vaporizer (8) as can
actually be vaporized. The liquid coolant then reverts to its
gaseous state in the vaporizer.
Outside air is fed through the vaporizer (8) by the fresh air
fan. While passing through the vaporizer (8) , the warmth it
contains is extracted from the outside air before it flows
through the air vents into the operator's cab.
That completes the circuit.
WA90-5 / WA100M-5 10-67

1. Magnetic clutch 8. Vaporizer

2. Compressor 9. Icing protection switch
3. Condenser 10. High-pressure, gaseous
4. Filter dryer 11. High-pressure, liquid
5. High-pressure switch 12. Low-pressure, liquid
6. Low-pressure switch 13. Low-pressure, gaseous
7. Expansion valve
10-68 WA90-5 / WA100M-5

The condenser
With a cooling system, warmth at a place where it is not required
is transported to another place where the warmth absorbed by
the vaporizer is fed on to the condenser. In the condenser, the
gaseous coolant is cooled and liquefied. The warmth removed
during liquefying is dissipated into the air by the condenser.
The coolant flows through three zones during this:
1st zone:
The gaseous coolant is cooled to condensation temperature by
dissipation of warmth (pre-cooling zone).
2nd zone:
The coolant transcends into liquid state by dissipation of the
condensation heat at a constant temperature (condensation
zone).
3rd zone:
The liquid coolant is cooled to below the condensation tempera-
ture, i.e. it is overcooled (overcooling zone).
The pressure (condensation pressure) is approximately constant

in all three zones. The coolant leaves the condenser in a liquid
state and, consequently, can be used again in the coolant circuit.
50°C / 8.2 bar
End of pre-cooling zone

33°C / 8.2 bar
+25°C Temperature of cooling air
End of condensation zone

33°C / 8.2 bar
End of overcooling zone

33°C / 8.2 bar
WA90-5 / WA100M-5 10-69

The vaporizer
Liquid coolant is sprayed into the vaporizer and converted to a
gaseous state. During this process, the coolant boils in the va-
porizer. The temperature of the coolant can fall well below the
freezing point during boiling. The coolant adopts a very similar
behaviour to boiling water in the vaporizer. The warmth which
the coolant requires to evaporate is withdrawn from its environ-
ment. At the end of the vaporizing process, the coolant emerges
as steam. The actual vaporizer has been lengthened in order to
allow any liquid bubbles which may possibly have been carried
along as a result of the turbulence time to evaporate as well.
This extension is called the after-vaporizer.
-10°C End of vaporizing zone

Begin of overheating zone
-3°C End of vaporizer
Vaporized
overheated
coolant
Injector nozzle
Liquid
coolant
+25°C
-10°C Begin of vaporizing zone
There are two fundamental methods of operation for vaporizers:
• Inundated vaporizers (disc vaporizers)
• Dry expansion vaporizers (round pipe and serpentine vapor-

izers)
While inundated vaporizers are generally bound to upright instal-

lation and coolant flow and require special measures for ensur-
ing oil return and avoiding cavitation, dry expansion vaporizers
where overheated steam is fundamentally present at the outlet
can be installed in virtually any position without any special mea-
sures having to be taken.
10-70 WA90-5 / WA100M-5

The filter dryer

The volume of circulating coolant varies with changing thermal
load. The filter dryer contains the required quantity of coolant for
this. It removes bubbles from the condensing coolant so that Inspection glass
only liquid coolant is forwarded to the expansion valve (bubbles
in the coolant reduce the performance of the air conditioning to
unit). expansion
from valve
Remove moisture from the coolant. condenser
Inspection glass allows a visual check of level of coolant in sys-

tem. Cleaning
sieve
Design
The filter dryer contains a cleaning sieve, a drying agent for re- Drying-
moving the moisture from the coolant, an inspection glass for agent
checking the level of coolant and a pressure switch (high and
low pressure) which switches the compressor off when the pres-
sure on the high pressure side of the system is too low or too
high.
Important instructions for operation

Because the drying agent in the filter dryer is very hygroscopic it
immediately absorbs moisture on coming into contact with the
air and loses its demoisturising property.
The drying agent cannot absorb more than approx. 6-12 g mois-
ture. For this reason, the inlet and outlet have to be sealed tight Outlet
with plugs whenever the filter dryer is removed.
Inlet
When installing the air conditioning unit in the vehicle, install all
other parts and pipelines first before removing the plugs and
mounting the filter dryer. Attention must be paid that the inlet
and outlet are not confused. If the inlet and the outlet have the
same form, the connection marked "IN" or with an arrow pointing
in the direction of the housing has to be connected to the con-
denser side. If connected the other way round, gaseous coolant
flows into the expansion valve which results in a considerable
drop in the coolant performance of the system
WA90-5 / WA100M-5 10-71

10-72 WA90-5 / WA100M-5

Installation of air conditioner
Condenser/blower unit
The condenser/blower unit is fixed behind the Cabine. 1 1 2
Before dismantling, the complete condenser/blower unit (2)

must have its air-conditioning system drained first, all rele-
vant hoses and cables disconnected and the unit then
propped up.
1
1. Close the hoses and filter dryer with cabs.
2. Secure the unit on frame against falling down.
3. Remove the 6 screws (1) on the left and right hand side .
4. Remove the condenser/blower unit.
5. Reinstall procedure in reverse order.

Use new seal .
Heater/air conditioner
The heater/air conditioner is located below the cab's windshield,
behind the front cover.
Compressor
The compressor is located in the engine compartment below the
generator.
WA90-5 / WA100M-5 10-73

Safety when handling coolants

When coolant circuits are opened, the contents may escape in
liquid or vapour form. The higher the pressure in the circuit, the
more violently this will happen.
Wear safety goggles!

Wear safety goggles. These prevent coolant from getting into
your eyes, which may cause severe frostbite damage.
Wear protective gloves!

Coolants are good solvents of greases and oils. They therefore
remove the protective film of grease on contact with the skin.
Degreased skin however, is sensitive to cold and disease-caus-
ing bacteria. Suitable protective gloves are an effective way of
avoiding degreasing skin.
Do not get liquid coolant onto the skin!

A coolant is designed for cooling. For this purpose, it needs to
evaporate. The coolant extracts the heat for evaporation from its
environment, even if this is the skin, and very low temperatures
are reached in the process. This leads to local freezing (frost-
bite).
Do not breathe in coolant vapours in high concentrations!

All coolants - even those which are liquid at room temperature -
evaporate when the circuit is opened. The vapours mingle with
the ambient air.
In the case of all types of coolant except for RI 1 and R113, the
main risk is that they will displace the oxygen in the air which is
necessary for breathing (risk of suffocation).
Ensure good ventilation!

In order to prevent occurrance of higher concentrations, work-
places must be well ventilated. The maximum working concen-
tration must be observed.
Exhaust system!
Opening windows and doors may not be sufficient, that means
an exhaust system must be installed at the point of exit if possi-
ble or close to the floor.
Do not smoke!
Coolants can decompose in the heat of a cigarette. The sub-
stances thus produced are toxic and should not be breathed in.
Do not let coolants escape during filling or repair work, but

transfer to recycling containers!
If coolants are allowed to escape in closed rooms, higher con-
centrations can arise which poses a risk to life due to narcotic ef-
fects or lack of oxygen.
10-74 WA90-5 / WA100M-5

Always transfer coolants from plants in need of repair into recy-

cling containers for temporary storage and, after the repair work,
refill into the plant or return to the dealer.
If high concentrations of coolant are present in the air, use

respiratory equipment which is independent of the ambient
atmosphere!
Filter masks with breathing filter A (solvents) can only remove
coolant vapours to a small extent. They may only be used if the
concentration does not exceed 0.5 % vol. (see respiratory equip-
ment specifications). If the concentration is too high, there is a
risk of suffocation particularly in pits and shafts, since coolant
vapours are heavier than air. In case of doubt, always use respi-
ratory equipment which is independent of the ambient atmo-
sphere.
Before carrying out welding and soldering work on cooling

systems, remove coolant from the relevant section of the
plant and eliminate residue by blowing through with air or
nitrogen!
Decomposition products generated from the coolant are not only
toxic but also have a strongly corrosive effect, so that pipelines
and parts of the plant may be attacked.
Pungent odour indicates decomposition of the coolant due

to overheating: Leave room immediately, ventilate well or
use filter mask with breathing filter B (acidic gases)!
If a pungent odour occurs, the above mentioned decomposition
products have already been generated. These substances
should not be breathed in under any circumstances, as this can
damage the respiratory channels, lungs and other organs. A fil-
ter mask with breathing filter B (acidic gases) provides effective
protection against these decomposition products. Observe the
instructions for use!
First aid
1. In the event of contact with the eyes or mucous membranes,
rinse out immediately with plenty of running water and con-
sult an eye specialist.
2. In the event of contact with the skin, remove wet clothing im-
mediately and rinse affected area of skin with plenty of wa-
ter.
3. If coolant vapours are breathed in in higher concentrations,

get the affected person into the fresh air immediately. Sum-
mon a doctor. Administer oxygen in the event of breathing
problems. If the affected person can no longer breathe or
cannot breathe properly, bend head to back of the neck and
resuscitate.
4. Information for the doctor:

Higher concentrations of coolants can lead to a restriction or
loss of consciousness. Since coolants make the heart sensi-
tive to catecholamine, no adrenomimetics should be admin-
istered. A lung oedema can occur even after an indefinite
latent period if decomposition products have been inhaled.
WA90-5 / WA100M-5 10-75

Operating the air conditioner
NOTE
Only operate the air-conditioning with the engine running.
NOTE
Run the air-conditioning for at least 10 minutes every month irre-
spective of season. This prevents the compressor shaft seal from
drying out.
Cab windows and doors must be closed when operating the air-
conditioning.
If the machine has been standing in the sun for a longer period
of time, we recommend airing the cab completely when starting
up the engine.
Switching on the air conditioner

1. Open all air circulation nozzles (see arrows).
2. Turn rotary switch (1) for fan to position 4 (the fan has to
G0065014b.ep
run).
3. Set the temperature control switch (2) to position ’cold’.
4. Press the switch (3) for the air conditioning. The air condi-
tioning system is now switched on and the control lamp in
the switch shines blue. The best cooling effect is achieved
with this setting, particularly if the engine is running at high
revs. As soon as the required temperature has been
reached, turn the blowers down by one stage and carry out
3
any further adjustment of the temperature using the temper-
ature control. The lowest blower setting can be used if only a 1 2
low cooling effect is required.
The air is distributed by means of air outlet nozzles.
• You may open or close the nozzles individually.
• The exhaust direction can be varied using the diffusing

disks.
• You can direct the air outlet nozzles to the front wind-
shield and to the side windows.
G0065014c
10-76 WA90-5 / WA100M-5

Maintenance of the air conditioner .
Maintenance timetable
VISUAL INSPECTION (once a month)
Drive belts Tension, condition
Compressor Leaks, unusual noises
Magnetic clutch Function
Condenser Damage, dirt
Condensation outlet underneath the vaporizer Dirt, blockages
Coolant Filling level in inspection glass
FUNCTIONAL TESTS (once a year)
High pressure, low pressure High pressure: Low pressure:
Emission temperature at air vents At maximum output:
Compressor control ON and OFF switching points
Condenser fan Rotational direction, noises
Air distribution, air circulation system Emission, control
Magnetic clutch Dirt, oil soiling
EXCHANGE (every 2 years)
Replace filter dryer, suck off coolant, dispose in an environmentally safe manner and fill the system with new coolant.
Maintenance instructions
• Always disconnect the battery if parts of the air conditioning
system are to be removed.
• Keep the system free of moisture and dust.
• Always seal cable glands immediately with cap plugs when

disconnecting cables.
• Only remove plugs or caps just before reconnecting cables

or lines.
• Apply a few drops of low temperature oil to the contact sur-

face of the O-ring or cone nut before connecting a hose or
line.
• Always use two spanners when tightening a connection in

order to prevent it from twisting.
• A disposal unit must be connected when draining the cool-

ing section of the system.
WA90-5 / WA100M-5 10-77

Regular maintenance
Check the air-conditioning system twice a year, in spring and au-
tumn.
The air conditioning system must be switched on at least once a

month for a brief time (approx. 10 min) so that the compressor is
lubricated.
The following maintenance work must be carried out at the be-

ginning, middle and end of a cooling period:
Check V-belt tension and compressor fastening.
1. Compressor
2. Fixing screw 2
3. Cover for Tension Pulley
1
2
3
Check coolant level, See chapter 10 STRUCTURE AND

FUNCTION "Checking coolant level" on page 10-82.
NOTE
The coolant must flow through the filter dryer's inspection glass
free of bubbles with the engine running and air conditioner at
maximum output (max. blower setting, top idling speed, setting
"cold").
Clean the condenser
The fins of the condenser must not be operating at exces-

sive pressure as this could deform the fins and reduce the
cooling output. Clean the condenser with cold water.
10-78 WA90-5 / WA100M-5

Clean filter fleece of heater unit
NOTE
If the filter fleece is to dirty it must be replaced.
1. Remove screws on the front cover (1) on the driver’s cab

(4 screws).
2. Withdraw filter (2) from the heater unit (3).
3. Clean the filter in warm water (30 - 40°C) which has had a
little household cleaning solvent added to it.
CAUTION! Neither rub the filter fleece nor wring it out!
4. Allow the filter fleece to dry.
5. Insert dried filter fleece (2) back into the heater unit (3).
1
6. Switch on the blower and check the air flow at the air outlet
nozzles.
CAUTION! The circulating air jets must be open!

2
7. If the air flow is still too weak the filter fleece must be re-
placed.
3
8. Screw front cover (1) back on.
WA90-5 / WA100M-5 10-79

Instructions for filling

Filling the air conditioning system should only be carried out by a
specialist for air conditioning systems.
For this reason, only a few instructions are provided here for fill-
ing the air conditioning systems installed in WA-5 models.
Use only original-coolant R134a and original PAG oil.
1. Drain valve and Filling valve

1
• Mixing with other coolants or oils can result in the de-

struction of the air conditioning system.
• The valves on the testing manometer should be closed
(manometer valves turned clockwise) when fastening the
snap-fit connectors to the system. The central valve con-
nection for selecting vacuum pump or filling canister con-
nection is therefore closed.
• An ambient temperature of at least 20°C (room/air) is re-
quired for a correct .
Filling
• Set prescribed quantity on fill unit or weigh.
glass
• Commence filling. pressure switch
OUT
• Start engine.
IN
• Check on inspection glass of filter dryer.
NOTE filter-
The filling is OK when the coolant flows without bubbles. See dryer
chapter 10 STRUCTURE AND FUNCTION "Checking coolant
level" on page 10-82.
Filling quantities (R134a)
WA90-5 1200 g
WA100M-5 1200 g
10-80 WA90-5 / WA100M-5

Evacuation
• Connect ball valves
• Set vacuum meter to 100 mbar
• Evacuate, min. 45 minutes
• Stop the evacuation process when the vacuum meter ap-

proaches the 0-bar marking.
Vacuum test
• Check the vacuum meter after 10 minutes for pressure in-
crease
A pressure increase is not permitted.
• In the event of pressure increase:
• Fill system with approx. 200 g
• Look for leakage points using leak finder
• Repair leaks
• Start siphoning off.
• No pressure rise:
• Fill system
Siphoning off coolant

• Close ball valves.
• Siphon off coolant into a measuring container; a certain

amount of compressor oil will also be siphoned off at the
same time.
• The same amount of compressor oil as was siphoned off

with the coolant must be replaced with new compressor oil.
• Extracted coolant and compressor oil must be disposed of in

accordance with regulations.
• The siphon pressure gauge must indicate slight over-pres-

sure before opening the drain valve in order to avoid any air
being sucked in.
WA90-5 / WA100M-5 10-81

Checking coolant level
If the liquid gets into your eyes or on your hands, it may

cause loss of sight or frostbite.
• Run the air conditioning system at maximum output for

5 - 10 minutes.
glass
• Check the flow of coolant (R134a) through the inspection pressure switch
glass for correct level of coolant. OUT
IN
filter-
dryer
Color condition Normal Abnormal
Temperature of high High pressure pipe is hot. Low High pressure pipe is warm. Low Almost no difference in temperature
and low pressures pressure pipe is cold. Clear differ- pressure pipe is cold. Little differ- between high and low pressure
pipes ence in temperature. ence in temperature. pipes.
Sight glass Almost transparent. All bubbles Bubbles are always visible. Some- Opaque substance is visible in the
disappear if the engine speed is times becomes transparent, or fluid.
increased or reduced. white bubbles appear.
Pipe connections Properly connected. Some parts contaminated with oil. Some parts heavily stained with oil.
There may be a leak somewhere. Almost all coolant has leaked out.
General conditions of Coolant level correct, no abnor-
Call service repair shop for inspec- Contact service repair shop immedi-
cooler malities. Ready for use.
tion. ately.
10-82 WA90-5 / WA100M-5

Checking the compressor oil level

Check, top up or change if:
• Compressor, vaporizer, condenser or drier have to be

changed.
• Coolant leaks from coolant circuit.
• Problems occur with the oil in the coolant circuit.
• The connectors from compressor or dryer was opened.
Compressor oil change

1. Remove compressor from the vehicle.
2. Drain the oil into a measuring beaker.
After the oil has flown out through the line, drain off any re-
sidual oil at the drain outlet by turning several times by hand.
3. After the oil has flown out through the line, drain off any re-
sidual oil at the drain outlet by turning several times by hand.
4. Screw in drain plug with new washer and tighten.
M A = 13 - 15 Nm
5. Fill up with new compressor oil to same amount as mea-

sured quantity of drained oil.
Exchange of magnetic clutch

If the magnetic clutch is faulty:
• Remove compressor
• Remove old clutch from compressor
• Connect new clutch to compressor
• Install compressor
• Switch on air conditioning system
• Operate compressor in neutral
• Switch air conditioning on for 10 seconds and off for 10 sec-

onds at least 10 times, check function of new clutch while
doing so.
WA90-5 / WA100M-5 10-83

Exchange of compressor
• Drain off coolant and dispose it in accordance with regula-
tions.
• Remount the hoses (1) and close them with cabs. 2
• Loosen the srews (2) on the compressor.

3
• Remove the protecting cover and belt.
• Remount the compressor. 1
. 2
Installing of a new compressor
NOTE
The new compressor is filled with 180 cm³ PAG oil and nitrogen
gas (N 2).
1. Loosen the discharge side connector's cab, release the ni-

trogen gas (N 2) from the compressor gently, close the con-
nectors immediately.
No compressor oil should escape!
2. Rotate the compressor several times by hand to distribute

the oil.
3. Replace the compressor under compliance of the ranges

shown in the figure above. Adjust the clearance using the
specified shims.
4. Remove the cabs and connect the hoses immediately.
The PAG oil is highly hygroscopic. Single components

must therefore be closed until they are installed.
5. Filling (See chapter 10 STRUCTURE AND FUNCTION "In-

structions for filling" on page 10-80.
10-84 WA90-5 / WA100M-5

Service operations
Fit the nuts and unions tightly against the base of the companion
pieces, then hand tighten the nut as much as possible to prevent
cross-threading.
Apply oil thoroughly to

these areas
right wrong wrong
O-ring Pipe bulge
right wrong
defect
part
Cone packing connections

• Fit the nuts and unions tightly against the base of the com-
panion pieces, then hand tighten the nut as much as possi- Armature
ble to prevent cross-threading. Copper seal
• Always use a back-up wrench and tighten fittings to the Seal cone
specified torque. The torque wrench should be used on the
fitting which is being tightened.
WA90-5 / WA100M-5 10-85

Troubleshooting
Checks prior to trouble shooting:
• Check belt tension
• Check condenser
• Check condenser blower, rotation direction right
• Compressor switches on and off
• Compressor clutch OK
• Function of air vents OK
• Coolant level OK (inspection glass)
• Condensation drain away
• Air temperature OK
Fault Cause Remedy
• System too full

Low pressure too high • Check filling level
• Condenser is dirty or blocked
• Clean condenser or replace
• Blower faulty or wrong rotational direc-
High pressure too high • Repair blower or replace
tion
Low pressure too low • Dryer blockes • Replace dryer

• Faulty expansion valve • Replace expansion valve
High pressure too high • Compressor faulty • Replace compressor
• Check drive belt - belt pulley - magnetic

Low and high pressure the same • Compressor faulty clutch, if all correct, proceed as for
"Compressor does not switch on"
Low pressure too low

• Faulty expansion valve • Replace expansion valve
• Dirty or blockes vaporizer • Clean or replace vaporizer
High pressure normal
• Expansion valve faulty

• Replace expansion valve
• Not enough coolant
• Refill air conditioning system
• Insufficient cooling effect only for short
• Evacuate system, replace dryer
Low pressure too low time; water in system, expansion valve
• Replace dryer or expansion valve
iced up as a result
• Check the ON and OFF times of the
High pressure too low • Dryer or expansion valve partially
compressor
blocked
• Adjust or replace the
• Vaporizer iced up
thermoswitch
• Thermoswitch not working
• Check electrical system (air conditioner

• Loose contact in the electric system switch, thermostat)
Compressor switches on and off at speed
• Coolant pressure too high • Check air conditioning system pressure
and refill if necessary
10-86 WA90-5 / WA100M-5

Fault Cause Remedy
• Check whether sensor lead has been

pushed into the vaporizer correctly
Compressor constantly running as well • Thermostat not working
• Check wether the sensor lead is okay
• Adjust or replace thermostat
• Not enough coolant in system • Check air conditioning system pressure

Compressor does not switch on • Air conditioning system power supply in- and refill if necessary
terrupted • Check electrical system
• Fault in the electrical system • Check electrical system

Condenser fan not working
• Fan faulty • Repair fan or replace
• Check pipe and line connections

• O-ring connection leaking
• Check pipes and lines
System leaking • Compressor shaft seal leaking
• Check whether magnetic clutch belt pul-
• Hose/line leaking
ley is oily
• Check whether sensor lead has been

pushed into the vaporizer correctly
Cooling output too low • Vaporizer iced up
• Check whether the sensor lead is okay
• Check whether compressor switches on

and off
• Compressor not switching off • Check whether sensor lead has been
Cooling output drops after a while
• Thermostat not working pushed into the vaporizer correctly
• Check electrical system

• Power supply interrupted
• Check filling level
Air conditioning system not working • Not enough coolant in the system
• Check magnetic clutch, replace if neces-
• Magnetic clutch faulty
sary
WA90-5 / WA100M-5 10-87

Fault Cause Remedy
• Check whether compressor switches on

and off
• Vaporizer iced up • Check whether sensor lead has been
White smoke emerging from the air vents
• Thermostat set too cold pushed into the vaporizer correctly
• Check whether the circulating air system

• Circulating air flaps not working or not
is working properly
Windows fogged up working properly
• Check that the condensation drain hose
• Condensation unable to drain away
is not blocked and is correctly laid
Bad smell coming from air conditioning • Check that the condensation drain hose
• Condensation not draining away
system is not blocked and is correctly laid.
10-88 WA90-5 / WA100M-5

WA90-5 / WA100M-5 10-89

10-90 WA90-5 / WA100M-5

20 TESTING AND ADJUSTING
Standard value table for engine –
WA90-5 / WA100M-5 ....................................... 20-3
Standard value table for chassis –
WA90-5 ............................................................ 20-4
Standard value table for chassis –
WA100M-5 ....................................................... 20-6
Standard value table for electrical parts ...... 20-8
Test certificate – WA90-5 ............................... 20-9
Test certificate – WA100M-5 ........................ 20-10
Valve lash clearance .................................... 20-11
Engine compression test ............................ 20-13
Injection nozzle pressure ............................ 20-14
Fuel injection timing .................................... 20-15
V-belt tension ............................................... 20-17
Engine RPM .................................................. 20-18
RPM-dependant drive take-up .................... 20-19
Engine stall torque RPM .............................. 20-20
Engine stall torque RPM, test with
the hydrostatic drive ................................... 20-20
hydrostatic drive and working hydraulics ... 20-21
Feed pump and servo oil pressure ............. 20-22
Hydraulic pressure cut-off .......................... 20-23
Working hydraulic pressure ........................ 20-25
Steering oil pressure ................................... 20-26
Pressure Accumulator ................................. 20-28
Operating time for steering wheel .............. 20-29
Operating force of steering wheel .............. 20-29
Disc brake ..................................................... 20-30
Inch valve – basic adjustment .................... 20-31
Brake efficiency ............................................ 20-32
Measuring the stopping distance ............... 20-32
Parking brake efficiency .............................. 20-33
Travel speed ................................................. 20-35
WA90-5 / WA100M-5 20-1

TESTING AND ADJUSTING
★ For more details of testing and adjusting the engine, see

Bulletin No. 3666418-00 (Cummins)
• When using the standard value table to make judgement

for testing, adjusting, and troubleshooting the following
precautions are necessary.
1. The standard values in the table are the values for a new
machine and are given as reference values for the time
when the machine is shipped from the factory. These val-
ues should be used as a guide when estimating wear and
tear after the machine has been operated, and when carry-
ing out repairs.
2. The permissible values given in the table are values esti-

mated based on the results of various tests carried out on
machines shipped from the factory. They should be used
together with other information such as repair conditions or
the operating history of the machine when judging the con-
dition of the machine.
3. These standard values do not form a basis for judging

claims.
• When carrying out testing, adjusting, or troubleshooting,

park the machine on level ground and use the safety
pins and blocks to prevent the machine from moving.
• When carrying out work together with other workers, al-
ways use signals and do not let unauthorized people
near the machine.
• When checking the water level, always wait for the water
to cool down. If the radiator cap is removed while the wa-
ter is still hot, the water will spurt out and cause burns.
• Be careful not to get caught in the fan, fan belt, or other
rotating parts.
20-2 WA90-5 / WA100M-5

TESTING AND ADJUSTING Standard value table for engine – WA90-5 / WA100M-5
Standard value table for engine – WA90-5 / WA100M-5

Item Measurement conditions Unit Standard value Permissible value
High idle RPM 2600 - 2700
Engine speed Low idle RPM 800 - 825

min-1 –
WA90-5 Rated speed 2350
Max. torque speed 1600
High idle RPM 2600 - 2700
Engine speed Low idle RPM 800 - 825

min-1 –
WA100M-5 Rated speed 2350
Max. torque speed 1600
At sudden acceleration Max. 3.8

Bacher- –
Exhaust gas color
ach index –
At high idling Max. 3.4
Intake valve 0.35

Valve clearance –
mm
(cold or hot) –
Exhaust valve 0.50
Oil temperature: 40-60°C

Compression pressure bar 29.5 19.6
(engine speed: starter motor)
Oil temperature: min. 82°C
Oil pressure At high idle RPM bar
At low idle RPM 0.78 –
Whole speed range (in oil pan)
Oil temperature Min. °C 100 120
Max. 110
4.5 (WA90-5)
Injection static timing Before top dead center position ° (degree) –
5.0 (WA100M-5)
Deflection when pressed with finger force

Fan belt tension mm 10 –
of approx. 6 kg
WA90-5 / WA100M-5 20-3

Standard value table for chassis – WA90-5 TESTING AND ADJUSTING
Standard value table for chassis – WA90-5
Permissible
Cat. Item Measurement conditions Unit Standard value
value
Hydrostatic • Engine water temperature green

Engine
2600 - 2700 –
stall range RPM
Hydrostatic and hydraulic stall • Hydraulic oil temperature: 50 - 60°C 2400 - 2500 –
N 5.6 - 21.8
Operating force –
(kg) (0.6 - 2.2)
α1
Accelerator pedal
Operating angle
α1 α2
° (degree) 44 –
–
α2
36
• Engine stopped
Play mm 0 - 40 –
• Machine facing straight to front
Steering wheel
N –
Operating force –
(kg) (–)
Operating time • Flat, even, straight, dry paved road

surface
at low idle RPM • Hydraulic oil temperature: 50 - 60°C s 4.5 - 5.5
–
–
at rated speed 2.5 - 3.3
Orbit-roll
• Engine speed: rated speed

Steering pressure bar 170 - 180 170 - 180
• Hydraulic oil temperature: 50 - 60°C
20-4 WA90-5 / WA100M-5

TESTING AND ADJUSTING Standard value table for chassis – WA90-5
Standard value table for chassis – WA90-5
Permissible
value
Brake
Performance • Flat, straight, dry paved road sur- m Max. 5 Max. 5

face
• Speed when applying brake, max.
speed, 2nd travel range
Parking brake
• Tire inflation pressure: specified

pressure
Performance • Flat, paved road with 18° gradient – Stopped –
• Dry road surface
• Machine at operating condition
Work equipment control lever
Operating force
Raise - Lower N 22.1 / 64.8

–
Tilt - Dump 26.7 / 22.6
• Engine speed: low idle RPM
• Operating force up to point of
pressure
Boom
Raise - Lower 86 / 95
mm –
Tilt - Dump 85 / 88
Main control valve
Work equipment hydraulic 215 - 225 –

bar
Servo valve
Servo pressure 26 - 30 –
Boom lifting time 4.8 - 5.0

Work equipment speed
Boom lowering time 3.7 - 3.9

Work equipment
Bucket dumping time 1.5 - 1.7

Ground to • Hydraulic oil temperature: 50 - 60°C
Bucket tilting time
s 0.9 - 1.1
end • Orbit-roll: neutral
• Empty bucket
Bucket hori-
zontal
WA90-5 / WA100M-5 20-5

Standard value table for chassis – WA100M-5 TESTING AND ADJUSTING
Standard value table for chassis – WA100M-5
Permissible
value
Hydrostatic • Engine water temperature green

Engine
2600 - 2700 –
stall range rpm
Hydrostatic and hydraulic stall • Hydraulic oil temperature: 50 - 60°C 2400 - 2500 –
N 5.6 - 21.8
Operating force –
(kg) (0.6 - 2.2)
α1
Accelerator pedal
Operating angle
α1 α2 44 –
° (degree)
α2 36 –
• Engine stopped
Play mm 0 - 40 –
• Machine facing straight to front
Steering wheel
N –
Operating force –
(kg) –
Operating time • Flat, even, straight, dry paved road

surface
at low idle RPM • Hydraulic oil temperature: 50 - 60°C s 4.5 - 5.5 –
at rated speed 2.5 - 3.3 –

Orbit-roll

Steering pressure bar 170 - 180 180
20-6 WA90-5 / WA100M-5

TESTING AND ADJUSTING Standard value table for chassis – WA100M-5
Standard value table for chassis – WA100M-5
Permissible
value
Brake
Performance • Flat, straight, dry paved road m Max. 5 Max. 5

surface
• Speed when applying brake, max.
speed, 2nd travel range
Parking brake
• Tire inflation pressure: specified

pressure
Performance • Flat, paved road with 18° gradient Stopped
• Dry road surface
• Machine at operating condition
Work equipment control lever
Operating force
Raise - Lower 22.1 / 64.8

N
Tilt - Dump 26.7 / 22.6
• Engine speed: low idle RPM
• Operating force up to point of
pressure
Boom
Raise - Lower 86 / 95
mm
Tilt - Dump 85 / 88
Main control valve
Work equipment hydraulic 235 - 245

bar
Servo-valve
Servo pressure 26 - 30
Boom lifting time 4.8 - 5.0

Work equipment speed
Boom lowering time 4.4 - 4.6

Work equipment
Bucket dumping time 1.5 - 1.7

Ground to • Hydraulic oil temperature: 50 - 60°C
Bucket tilting time
s 0.8 - 1.0
end • Orbit-roll: neutral
• Empty bucket
Bucket hori-
zontal
WA90-5 / WA100M-5 20-7

Standard value table for electrical parts TESTING AND ADJUSTING
Standard value table for electrical parts

Connec- Insp. Measurement
Name of component Judgement table
tor No. method conditions
If the condition is as shown in the table below, the sensor
Check continuity
is normal.
Start engine.
Engine oil pressure
Oil pressure above 0.7 bar no continuity Disconnect connec-
sensor
tors.
Oil pressure below 0.3 bar continuity
Measure resistance If the condition is as shown in the table below, the sensor
is normal.
Turn starting switch

Fuel level sensor Full ca. 2.2 Ω OFF.
Empty ca. 88.5 Ω

Measure resistance
is normal.
Engine coolant temper- Turn starting switch

ature sensor Temperature normal (25°C) ca. 42.7 kΩ OFF.
106°C ca. 3.2 kΩ

Check continuity
Full open
Turn starting switch
Brake oil reservoir
OFF.
Empty continuity

Measure resistance
is normal.
Ribbon heater tempera- Turn starting switch

ture sender unit Between OFF.
Temp. normal (25°C) ca. 600 Ω
connection
0°C ca. 1.9 kΩ
and chassis
20-8 WA90-5 / WA100M-5

TESTING AND ADJUSTING Test certificate – WA90-5
Test certificate – WA90-5
Chassis Nº: Customer:

Test temperatures Nominal Actual
1 Cooling water °C 75 - 85
2 Hydraulic oil (drive and working hydraulic, measured in the tank) 35 - 45
Engine speeds Nominal Actual
3 Low idle speed 800 - 850
4 High idle speed 2600 - 2700

rpm
5 Stall speed against hydrostatic (50 - 60°C oil temperature) 2500 - 2600
6 Stall speed against hydrostatic and hydraulic 2400 - 2500
7 Start of drive RPM 1100 - 1200
System pressures Nominal Actual
8 Work hydraulic pressure 215 - 225
9 Steering pressure 170 - 180
10 Servo pressure (low idle speed and test temperature) bar min. 26
11 Servo pressure (high idle speed and test temperature) max. 30
12 Drive pressure with blocked wheels, forward 450 - 460
13 Drive pressure with blocked wheels, reverse 450 - 460
Steering times Nominal Actual
14 Low idle speed, left and right (end to end) 4.5 - 5.5
15 Rated idle speed, left and right (end to end) 2.5 - 3.3
Lift and dump times Nominal Actual
16 Lift time with bucket (empty) 4.8 - 5.0

s
17 Bucket dump, boom highest position 1.5 - 1.7
18 Tilting, ground to end 0.9 - 1.1
Lower times Nominal Actual
19 Lower time with empty bucket to ground 4.3 - 4.5
20 Lower time with empty bucket to ground in float position 4.2 - 4.4
Travel speeds Nominal Actual
21 1. travel range: 0 up to 5.6 km/h (Tires 405/70R20 SPT9) km/h
22 2. travel range: 0 up to 20 km/h (Tires 405/70R20 SPT9) 20
All pressures and timings have to be measured at working temperature of the machine.
WA90-5 / WA100M-5 20-9

Test certificate – WA100M-5 TESTING AND ADJUSTING
Test certificate – WA100M-5
Chassis-no.: Customer:
Test temperatures Nominal Actual
1 Cooling water °C 75 - 85
2 Hydraulic oil (drive and working hydraulic, measured in the tank) 35 - 45
Engine speeds Nominal Actual
3 Low idle speed 800 - 850
4 High idle speed 2600 - 2700

rpm
5 Stall speed against hydrostatic (50 - 60°C oil temperature) 2500 - 2600
6 Stall speed against hydrostatic and hydraulic 2400 - 2500
7 Start of drive RPM 1100 - 1200
System pressures Nominal Actual
8 Work hydraulic pressure 235 - 245
9 Steering pressure 170 - 180
10 Servo pressure (low idle speed and test temperature) bar min. 26
11 Servo pressure (high idle speed and test temperature) max. 30
12 Drive pressure with blocked wheels, forward 450 - 460
13 Drive pressure with blocked wheels, reverse 450 - 460
Steering times Nominal Actual
14 Low idle speed, left and right (end to end) 4.5 - 5.5
15 Rated idle speed, left and right (end to end) 2.5 - 3.3
Lift and dump times Nominal Actual
16 Lift time with bucket (empty) 4.8 - 5.0

s
17 Bucket dump, boom highest position 1.5 - 1.7
18 Tilting, ground to end 0.8 - 1.0
Lower times Nominal Actual
19 Lower time with empty bucket to ground 4.4 - 4.6
20 Lower time with empty bucket to ground in float position 3.7 - 3.9
Travel speeds Nominal Actual
21 1. travel range: 0 up to 5.0 km/h (Tires 455/70R20 SPT9) km/h
22 2. travel range: 0 up to 21 km/h (Tires 455/70R20 SPT9) 20
All pressures and timings have to be measured at working temperature of the machine.
20-10 WA90-5 / WA100M-5

TESTING AND ADJUSTING Valve lash clearance
Valve lash clearance
Park the machine on level ground and secure it against roll-

1
ing away and jack-knifing!
Lower the bucket, switch the engine off and actuate the
parking brake!
★ The adjustment must be carried out at cold engine!
1. Unscrew the three bolts (1) and remove the cylinder head
cover (2).
2. Rotate the crankshaft in the normal direction (as indicated

by the arrow), using the crankshaft pulley mounting cap
screw (3) or the alternator pulley mounting nut (4).
3. While watching the movement of the intake valve of the

No. 4 cylinder (4i), bring the No. 1 cylinder into compression
top dead center (TDC) position.
4. Align the engraved mark "1.4" on the crankshaft pulley (5) 6 5

with the pointer (6).
1.4
10
5. Adjust the valve clearances of the four valves (1i), (1e), (2e)
and (3i) one after the other as follows:
a. Loosen the locknut (a) on the adjustment screw (b).
b. Insert the feeler gauge (c) between the valve stem (d)
and the rocker arm (e).
c. Adjust the clearance with the adjustment screw (b) until

slight drag is felt on the feeler gauge.
Valve clearance (engine cold):
Intake valves (i) Exhaust valves (e)
0.35 mm 0.50 mm
0.014 in 0.020 in
WA90-5 / WA100M-5 20-11

Valve lash clearance TESTING AND ADJUSTING
d. Tighten the locknut (a).
Locknut tightening torques
Nm ft-lb
MIN 39 29
MAX 49 36
6. Rotate the crankshaft clockwise for one revolution (360°) 6 5

and align the engraved mark "1.4" on the crankshaft pulley
(5) with the pointer (6) again.
1.4
10
7. Adjust the valve clearances for the four valves (2i), (3e), (4i)
and (4e) one after the other as described above.
8. Fasten the cylinder head cover with the three bolts (1).
20-12 WA90-5 / WA100M-5

TESTING AND ADJUSTING Engine compression test
Engine compression test
• Park the machine on level ground and secure it against

rolling away and jack-knifing!
parking brake!
• Make sure, while testing the engine compression, that you
do not come in contact with hot engine parts and that
clothes do not come in contact with rotating parts, such
as the V-belt or pulleys!
★ Testing conditions
• Normal engine working temperature
• Correct engine valve adjustment
1. Remove the injectors.
★ Make sure that no contamination enters the cylinders.
2. Turn the engine with the starter and the injection pump to
stop position before fitting the adapter (P/N: 795-502-1370).
★ Do not forget to fit a seal to the compression tester

adapter.
3. Install the compression tester (P/N: 795-502-1590, testing

range 35 bar) on the adapter.
4. Using the procedure in step 2, turn the engine over using the Adapter P/N: 795-502-1370
starter motor. Note the max. stabile pressure registered on
the compression tester.
Compression pressure:
Compression pressure at 320 - 360 rpm

Standard Minimum limit
29.5 bar 19.6 bar
WA90-5 / WA100M-5 20-13

Injection nozzle pressure TESTING AND ADJUSTING
Injection nozzle pressure

parking brake!
1. Remove the injection pipes and close the connections. Re-

move the overflow lines.
★ Make sure that no contamination enters the injection

pump and injection valves.
2. Remove the injection valve brackets and remove the injec-

tion valves.
3. Remove carbon deposit at the nozzle hole thoroughly.
4. Connect the injection valve (1) to the high pressure pipe (2)
of the nozzle tester (3).
5. Operate the lever (4) slowly and read the pressure at the
moment when the injection from the nozzle starts.
Injection nozzle pressure:

207 - 211 bar
6. If the measured injection pressure is too low, replace the

pressure adjusting shim (5) with a thicker one.
Available pressure adjusting shims:

1 × 0.1 mm 1 × 0.2 mm 1 × 0.3 mm
1 × 0.4 mm 1 × 0.5 mm 1 × 0.51 mm
1 × 0.52 mm 1 × 0.53 mm 1 × 0.54 mm
1 × 0.55 mm 1 × 0.56 mm 1 × 0.57 mm
1 × 0.58 mm 1 × 0.59 mm 5
For the part numbers see the Komatsu parts book (injection
system).
The injection pressure increases approx. 14.7 bar, when

the adjusting shim thickness is increased by 0.1 mm.
Tightening torque:
39.2 - 44.1 Nm
20-14 WA90-5 / WA100M-5

TESTING AND ADJUSTING Fuel injection timing
Fuel injection timing

parking brake!
If the injection pump is installed on the original machine

6 5
and the pump has not been repaired:
1. Set the No. 1 cylinder at compression top dead center 10
(TDC) by aligning the pointer (6) on the gear cover with the 1.4
TDC line (1.4) on the crankshaft pulley.
★ The mark "C" can only be seen if the injection pump’s

cover is removed.
2. Confirm that the mark "C" can be seen on the idler gear. If
the mark "C" cannot be seen, rotate the crankshaft one com-
plete revolution and confirm that "C" can be seen.
3. Align the match mark "C" on the injection pump gear with
the match mark "C" on the idler gear during installation for
correct alignment.
4. Align the stamped line "a" on the injection pump with the
stamped line "b" on the timing gear case during installation
for correct alignment.
5. Install the injection pump.
6. If the stamped lines are out of alignment, loosen nut (7).

Align the stamped lines by rotating the coupling. Tighten the
nut.
If an injection pump is installed to the engine that has been

repaired:
1. Set the No. 1 cylinder at compression top dead center
6 5
(TDC) by aligning the pointer (6) on the gear cover with the
1.4
10
WA90-5 / WA100M-5 20-15

Fuel injection timing TESTING AND ADJUSTING
TDC line (1.4) on the crankshaft pulley.
2. Remove the distributor head bolt and copper washer from

the injection pump. Discard the copper washer.
3. Install the dial gauge into the distributor head, so that the
stylus end of the dial gauge contacts the plunger head.
4. Slightly rotate the crankshaft in the opposite normal direc-

tion (counterclockwise) until the dial gauge does not move
any longer.
5. Set the dial gauge pointer to 0.
6. Rotate the crankshaft in the normal direction (clockwise)

without stopping until it reads 1.0 ± 0.3 mm.
7. The pointer on the crankshaft must point to the timing mark

(in degrees) on the crank pulley as indicated on the data-
plate. The timing marks on the crank pulley range from 6 to
14 degrees in two degree increments.
★ Check the values on the dataplate. Values may change

as new ratings are developed.
★ The gauge reading ± 0.03 mm (0.001 in) is equivalent to

± 0.5 degrees fuel injection timing.
8. If the dial gauge reading is not within the standard value,

loosen the nut and adjust the fuel injection timing by rotating
the injection pump body. Tighten the nut.
9. Remove the dial gauge. Install the distributor head bolt and
a new copper washer into the injection pump. Tighten the
bolt.
 14 - 20 Nm
10. Stamp a match mark on the injection pump and the timing
gear case.
20-16 WA90-5 / WA100M-5

TESTING AND ADJUSTING V-belt tension
V-belt tension

parking brake!
1. Press the fan belt at position (1) between the crankshaft pul-
ley (2) and the alternator pulley (3) with a finger (59 N, 6 kg).
The tension is correct if the deflection at position (1) is be-

tween 7 and 10 mm.
Do not adjust the belt tension to maximum. The tension can

rise when the locking nut is tightened. The life of the pul-
leys and bearings is reduced if the tension is too high!
2. Adjusting the fan belt tension
a. Release the locknut (4) and the nut (5).
b. Tense the V-belt by applying a lever between the engine

block and the alternator.
c. After having adjusted the tension tighten the locknut (4)

and the nut (5).
d. Check the tension again to make sure it is not too high.
WA90-5 / WA100M-5 20-17

Engine RPM TESTING AND ADJUSTING
Engine RPM
Do not touch hot engine parts during fitting or removing

test equipment!
1. Fit the RPM tester to the engine.
2. Note the low idle RPM, when the engine has reached work-
ing temperature.
Low idle RPM:
WA 90-5 800 - 825 rpm

WA 100M-5 800 - 825 rpm
3. If the low idle RPM is not correct, screw the adjusting screw
(1) to set the low idle RPM.
★ Screwing the adjusting screw in increases the RPM.

Screwing the adjusting screw out decreases the RPM.
4. Slowly rise the RPM (no load) and note the high idle RPM.
High idle RPM:
WA90-5 2600 - 2700 rpm

WA100M-5 2600 - 2700 rpm
5. If the high idle RPM is not correct, screw the adjusting screw
(2) to set the high idle RPM.
★ Screwing the adjusting screw in decreases the RPM.

Screwing the adjusting screw out increases the RPM.
20-18 WA90-5 / WA100M-5

TESTING AND ADJUSTING RPM-dependant drive take-up
RPM-dependant drive take-up
Make sure that the test area is safe!
• Ground: flat, even, dry and hard surface
• Tyre pressure: recommended pressure
Testing
1. Fit the RPM tester to the engine and take the RPM tester’s
display into the cab.
2. Release the parking brake and select FORWARD.
3. Press the accelerator pedal and increase the engine RPM

slowly.
1
4. Note the indicated engine speed, when the machine just
starts to move forward.
Engine speed at drive start: 1050 - 1150 RPM
Adjusting
Stop the engine before adjusting the oil pressure!
1. Release the locknut (3) of the regulating valve (1).
2. Adjust the setting with the adjusting screw (2).
To rise the RPM-dependant drive take-up screw in

To lower the RPM-dependant drive take-up screw out
★ Repeat the test to check that the drive take-up is in the

given limits.
WA90-5 / WA100M-5 20-19

Engine stall torque RPM TESTING AND ADJUSTING
Engine stall torque RPM
• Do not touch hot engine parts during fitting or removing

test equipment!
• Chock the wheels!
1. Fit the RPM tester to the engine and take the RPM tester’s
display into the cab.
2. Block the drive train (1). Make sure that the wheels cannot
slip during the test.
★ Make sure that the correct low and high idle speeds are
adjusted and that the oil pressures is in between the set
limits. If these are not correct, check the connections
and the linkages.
Engine stall torque RPM, test with the

hydrostatic drive
Clear the possible danger area, in case the machine be-

comes free from the safety arrangements!
1. Run the engine in low idle.
2. Release the parking brake.
3. Select FORWARD.
4. Press the brake pedal and slowly rise the engine RPM to
max.
★ Make sure that the wheels do not turn during the test.
5. Note the maximum engine RPM when the engine is under

hydrostatic load.
★ Do not hold this test condition for more than 20 sec.

Check that the oil temperature does not exceed 60°C.
Engine stall speed against hydrostatic: 2500 - 2600 RPM
20-20 WA90-5 / WA100M-5

TESTING AND ADJUSTING Engine stall torque RPM

hydrostatic drive and working hydraulics
★ The test is the same as the previous one except that now
the working hydraulics are also used at the same time.

1. Run the engine in low idle.
3. Select FORWARD.
4. Press the brake pedal and slowly rise the engine RPM to
max.
★ Make sure that the wheels do not turn during the test.
5. Move the boom lift hydraulic control lever and raise the
boom until the main pressure relief valve opens. The boom
is held in the upper stop position.
★ Use the control lever positively.
6. Note the engine max. RPM in this condition, with hydrostatic

drive and boom rise.
★ Do not hold this test condition for more than 20 sec.

Check that the oil temperature does not exceed 60°C.
Engine stall speed against hydrostatic and hydraulic:

2400 - 2500 RPM
WA90-5 / WA100M-5 20-21

Feed pump and servo oil pressure TESTING AND ADJUSTING
Feed pump and servo oil pressure

★ The hydrostatic drive feed pump oil is also used for the ser-
vo control system. If the feed pump oil pressure is changed
this will also influence the servo control oil pressure.
The feed pump oil pressure and the servo system oil pres-
sure are the same.
Apply the parking brake and chock the wheels!
Testing
1. Connect a pressure testing gauge (60 bar) to the testing
point (1).
2. Run the engine at high idle RPM.
★ Make sure that the correct low and high idle speeds are
adjusted.
3. Note the pressure shown on the pressure testing gauge.
Feed pump oil and servo oil pressure: 30 bar
20-22 WA90-5 / WA100M-5

TESTING AND ADJUSTING Hydraulic pressure cut-off
Hydraulic pressure cut-off

Testing
1. Connect a pressure test gauge (testing range up to 600 bar)
to the test connector (1) for FORWARD.
2. Block the drive train so that the machine cannot move for-
ward. Make sure that the wheels cannot slip during the test.
★ Do not use the service or park brake during the test!
3. Start the engine and select FORWARD.
4. Run the engine to max. RPM and note the pressure shown
on the pressure gauge.
Hydraulic pressure cut-off (forward): 450 - 460 bar
★ Repeat the test when the machine is blocked in reverse.
5. Connect a pressure test gauge (testing range up to 600 bar)

to the test connector (2) for REVERSE.
6. Block the drive train so that the machine cannot move back-
wards. Make sure that the wheels cannot slip during the
test.
★ Do not use the service or park brake during the test!
7. Start the engine and select REVERSE.
8. Run the engine to max. RPM and note the pressure shown
on the pressure gauge.
★ The pressure should be the same for forward and re-

verse.
Hydraulic pressure cut-off (reverse): 450 - 460 bar
WA90-5 / WA100M-5 20-23

Hydraulic pressure cut-off TESTING AND ADJUSTING
Adjustment
Always stop the engine when adjusting oil pressure!
1. Release the locknut (5) of the cut-off valve (3).

3
2. Adjust the pressure by turning the adjusting screw (4).
To rise the pressure screw in

2
To lower the pressure screw out
★ Repeat the test procedure and check that the pressure

is in the specified limits.
3. Tighten the locknut (5). 1
20-24 WA90-5 / WA100M-5

TESTING AND ADJUSTING Working hydraulic pressure
Working hydraulic pressure
Testing
1. Connect a pressure testing gauge (1) (testing range up to
250 bar) to the test point (2).
2. Start the engine and run at full RPM.
3. Move the hydraulic control lever to LIFT and hold it in the

end position so that the main pressure release valve opens.
4. Note the pressure on the pressure testing gauge.
★ Do not hold the pressure for more than 20 sec. Use the
control lever by quick handling.
Working hydraulic pressure:
WA90-5 220 bar

WA100M-5 240 bar
Adjusting
Always stop the engine when adjusting oil pressure!
★ The main pressure release valve is on the front of the main

control valve (4). It can be adjusted through the opening be-
tween front frame and front axle without opening the front
frame.
1. Release the locknut (6) on the main pressure release valve.
2. Adjust the pressure by turning the pressure adjusting

screw (4).
5 6
To rise the pressure screw in
To lower the pressure screw out
★ Repeat the test procedure and check that the pressure

is in the specified limits.
WA90-5 / WA100M-5 20-25

Steering oil pressure TESTING AND ADJUSTING
Steering oil pressure
Testing
1. Fit the steering safety rod in the articulation joint so that the
machine can not be steered.
2. Connect a pressure testing gauge (1) (testing range up to

250 bar) to the test point (2).
★ Test point (2) corresponds to "POS. 1" in the hydraulic L 2 R
240 bar
3 240 bar
diagrams. By connecting the pressure testing gauge the

pressure is increased by 10 bar. 4
7
★ It is also possible to install a T-joint to the steering cylin-

der ("POS. 2" in the hydraulic diagrams) to measure the
pressure.
5
320-160 ccm/U
3. Start the engine and run at full RPM. 175 bar

8
6
4. Turn the steering wheel to the right until the end position is P T LS
POS.2
reached and hold.
Work-
hydraulic
★ The steering safety rod is pulled to the right when the 1 1

steering wheel is turned. POS.1 EF CF
9 LS
5. Note the pressure shown on the pressure testing gauge.

32 8
10
Steering oil pressure on "POS. 1":
185 bar (175 + 10 bar) 11
WA90-5
WA100M-5
Steering oil pressure on "POS. 2":
185 bar (175 + 10 bar)
20-26 WA90-5 / WA100M-5

TESTING AND ADJUSTING Steering oil pressure
Adjusting
DANGER! Risk of accident!

If the steering oil pressure is not correctly adjusted, the
steering may malfunction. Adjustment of the steering oil
pressure must be performed by qualified personnel, only!
1. Adjust the steering oil pressure with the pressure limiting

valve (5) (primary side) and with the shock valve (6) (sec-
ondary side).
1 control piston 7 prefill valve

2 control bushing 8 prefill valve
3 rotor set 9 non-return valve
4 centring spring 10 cut off valve
5 pressure limiting valve 11 non-return valve
6 shock valve 12 non-return valve
WA90-5 / WA100M-5 20-27

Pressure Accumulator TESTING AND ADJUSTING
Pressure Accumulator
★ Check the pressure accumulator for the pilot valve at inter-
vals of 500 hours.
Preparation

parking brake!
Testing
• Danger of Injury! Pressure accumulator is filled with high-

ly pressurized nitrogen. Wear safety equipment.
• Do not hit the pressure accumulator.
• Keep fire and sources of heat away from the pressure ac-
cumulator.
• Do not weld any parts to the pressure accumulator.
• Do not touch hot engine parts during fitting or removing
test equipment.
1. Move the Multifunctional lever several times to all directions.
2. Loosen the filler / vent plug of the hydraulic system for 1-2
sec. to depressurize the system.
3. Tighten the filler / vent plug.
4. Remove the cap (1) of the pressure accumulator (2).
5. Connect the nitrogen refill equipment.
6. Check the pressure.
Standard pressure is 20 bar.
7. If the pressure is too low, refill the pressure accumulator

with nitrogen.
8. If the pressure accumulator is damaged, replace it.
9. Disconnect the nitrogen refill equipment and attach the

cap (1) to the pressure accumulator (2).
10. After the testing procedure, perform an operating test of the

pressure accumulator.
20-28 WA90-5 / WA100M-5

TESTING AND ADJUSTING Operating time for steering wheel
Operating time for steering wheel

Testing
1. Start the engine, raise the bucket approx. 400 mm.
2. Operate the steering wheel to one end of its stroke to turn

the machine to the left or right.
3. Measure the time to operate the steering wheel from one

end to the other end of the stroke.
★ Operate the steering wheel as quickly as possible with-

out using force.
★ Carry out the measurements both at low and high idle

speed and to both sides left and right.
Operating time (low idle speed): 4.5 - 5.5 s

Operating time (high idle speed): 2.5 - 3.3 s
Operating force of steering wheel

Testing
1. Install a push-pull scale to the steering wheel knob.
2. Start the engine, raise the bucket approx. 400 mm.
3. Pull the push-pull scale in the tangential direction and mea-

sure the value when the steering wheel moves smoothly.
★ Avoid measuring when the steering wheel starts to

move.
WA90-5 / WA100M-5 20-29

Disc brake TESTING AND ADJUSTING
Disc brake
Testing
★ The axle has to be disassembled to check the brake disc
and separator disc thicknesses. See chapter 30 DISAS-
SEMBLY AND ASSEMBLY "Rear axle assembly" on page
30-50.
1. Check the friction plate (1) thickness.
Friction plate thickness (new): 10.0 ± 0.1 mm

(worn): 8.8 mm
2. Check the separator plate (2) thickness.
Separator plate thickness (new): 11.7 ± 0.05 mm
20-30 WA90-5 / WA100M-5

TESTING AND ADJUSTING Inch valve – basic adjustment
Inch valve – basic adjustment

parking brake!
B = 45°
Length of rod
1. Mount the fork joint to the brake rod, loosen the locking nut
(3) and set the length of the brake rod to approx. 110.5 mm.
2. Install the brake rod to the brake pedal.
Angle of brake pedal

1. Release the locknut (2) and turn the adjusting nut (1) to
move the pedal angle (B) to 45°.
2. Tighten the locknut (2) and check the pedal angle adjust-
ment (B).
WA90-5 / WA100M-5 20-31

Brake efficiency TESTING AND ADJUSTING
Brake efficiency
Measuring the stopping distance
Danger! Fasten the seat belt before testing the brakes!
• Speed: highest speed when starting to brake
Testing
★ Set up a test run and mark the point where you will start to
brake. Brake as soon as you pass this point.
1. Start the engine and drive off.
2. Set the speed at 20 km/h.
3. Using the correct force, press the brakes when passing the
braking point with 20 km/h.
4. Measure the distance taken to stop from the point of starting

to brake.
★ The distance should be less than 5 m.
Stop point Point at which the Start of braking

brakes start to react
Stopping distance max. 5m Run-up
20-32 WA90-5 / WA100M-5

TESTING AND ADJUSTING Parking brake efficiency
Parking brake efficiency

• Ground: flat, even, dry and hard surface, 18% gradient.
• Tyre pressure: correct pressure

• Bucket: empty
Testing
1. Start the engine and set the machine straight ahead. Drive
the machine up the 18% gradient.
2. Use the foot brake to stop the machine and hold.
3. Lower the bucket.
4. Put the forward/ reverse lever in NEUTRAL and stop the en-
gine.
5. Apply the parking brake, slowly release the foot brake. The
machine should not move.
6. Test the parking brake twice. Once facing up the gradient

and once facing down the gradient.
Adjusting
★ Adjust the parking brake if it does not function properly. Re-
peat the adjustment of the parking brake at intervals of 300
hours, independently of the function.

parking brake!
1. Chock the wheels.
3. Clean the brake pads and the disc.
4. Loosen the parking brake cable.
5. Loosen the hydraulic hose (1) in the front frame.
6. Remove the breather from the hydraulic hose.
NOTE
The hydraulic hose is filled with oil. Do not spill the oil.
WA90-5 / WA100M-5 20-33

Parking brake efficiency TESTING AND ADJUSTING
Danger of Injury! Wear safety equipment when handling

high pressurized fluids.
7. Apply a hydraulic pressure of 15 - 20 bar to the hydraulic

hose. The application of pneumatic pressure is also possi-
ble, but hydraulic pressure is preferred.
NOTE
Do not apply excessive pressure. The pressure causes the brake
pads (2) to move towards the brake disc.
8. Repeat step 7 two more times.
9. If you have applied pneumatic pressure in step 7, you have

to refill the hydraulic hose with oil.
10. Attach the breather to the hydraulic hose (1).
11. Reconnect the hydraulic hose (1).
12. Readjust the parking brake cable.
NOTE
Do not tighten the parking brake cable. In the "released" position
of the parking brake, the parking brake cable must be slack.
20-34 WA90-5 / WA100M-5

TESTING AND ADJUSTING Travel speed
Travel speed
• Speed: the highest speed possible should be reached

before passing test point "1" and held over the complete
test run.
Testing
★ Before starting the test set up the test points "1" and "2" and
measure the exact distance.
1. Start the engine and drive off.
2. Select the speed range 20 km/h.
3. Drive the machine at max. speed over the complete test run.
4. Start the stop watch when passing point "1" and stop the
stop watch when passing point "2". Formula for testing
machine speed
5. Copy the stopped time (Y) and the driven distance (X) be-
tween point "1" and "2" to the formula given.
x
× 3.6 = km/h
y
★ Repeat the test three times to get an average speed.
100 m
Example: × 3.6 = 20 km/h
18s
Point 2 Point 1
Test run distance X in meters Run-up to test
WA90-5 / WA100M-5 20-35

Travel speed TESTING AND ADJUSTING
20-36 WA90-5 / WA100M-5

30 DISASSEMBLY AND ASSEMBLY
Comments .............................................. 30-3 Main control valve assembly .............. 30-38
Starter assembly .................................... 30-4 Removal of main control valve
assembly ........................................................30-38
Removal of starter assembly ........................... 30-4
Installation of main control valve
Installation of starter assembly ........................ 30-5
assembly ........................................................30-39
Alternator assembly .............................. 30-6 Pilot valve assembly ............................ 30-40
Removal of alternator assembly ...................... 30-6
Removal of pilot valve assembly ...................30-40
Installation of alternator assembly ................... 30-7
Installation of pilot valve assembly ................30-41
Water pump assembly ........................... 30-8 Monitor assembly ................................. 30-42
Removal of water pump assembly .................. 30-8
Removal of monitor assembly .......................30-42
Installation of water pump assembly ............. 30-10 Installation of monitor assembly ....................30-43
Engine cover assembly ....................... 30-11 Articulated joint assembly .................. 30-44
Removal of engine cover assembly .............. 30-11 Removal of articulated joint assembly ...........30-44
Installation of engine cover assembly ........... 30-12
Installation of articulated joint assembly ........30-45
Engine cover support assembly ......... 30-13 Variable motor assembly ..................... 30-46
Removal of engine cover support
Removal of variable motor assembly .............30-46
assembly ....................................................... 30-13
Installation of variable motor assembly ..........30-48
Installation of engine cover support
assembly ....................................................... 30-14 Rear axle assembly .............................. 30-49
Engine assembly .................................. 30-15 Removal of rear axle assembly .....................30-49
Removal of engine assembly ........................ 30-15 Installation of rear axle assembly ..................30-51
Installation of engine assembly ..................... 30-20 Front axle assembly ............................. 30-52
Clutch assembly .................................. 30-22 Removal of front axle assembly .....................30-52
Installation of front axle assembly ..................30-54
Removal of clutch assembly ......................... 30-22
Installation of clutch assembly ...................... 30-23 Front axle .............................................. 30-55
Radiator assembly ............................... 30-24 Brake disc group ............................................30-55
Removal of radiator assembly ....................... 30-24 Brake caliper ........................................ 30-59
Installation of radiator assembly .................... 30-26 Hydraulic principle of operation .....................30-59
Fan assembly ....................................... 30-27 Differential position ........................................30-60
Removal of fan assembly .............................. 30-27 Mechanical principle of operation ..................30-60
Caliper removal ..............................................30-60
Installation of fan assembly ........................... 30-28
Caliper reassembly ........................................30-65
Main brake cylinder assembly ............ 30-29 Replacement of guide protective covers ........30-65
Removal of main brake cylinder Pad replacement ............................................30-66
assembly ....................................................... 30-29
Brake group - wheel shaft ..............................30-67
Installation of main brake cylinder
assembly ....................................................... 30-30 Rear axle ............................................... 30-73
Trunnions group and flange ...........................30-73
Priority valve assembly ....................... 30-31
Epicyclic reduction gear group .......................30-76
Removal of priority valve assembly ............... 30-31
Wheel hub ......................................................30-78
Installation of priority valve assembly ............ 30-32
Wheel shaft ....................................................30-82
Orbit-roll-valve assembly .................... 30-33 Differential support group ..............................30-84
Removal of orbit-roll-valve assembly ............ 30-33 Bevel gear marking test .................................30-88
Installation of orbit-roll-valve assembly ......... 30-35 Differential locking group ...............................30-89
Counterweight assembly .................... 30-36 Differential group (100% Diff. Lock) ...............30-91
Removal of counterweight assembly ............ 30-36 Differential group (LSD 25%) .........................30-93
Installation of counterweight assembly ......... 30-37 Pinion group ...................................................30-95
WA90-5 / WA100M-5 30-1

Variable displacement pump
assembly ............................................... 30-99
Removal of variable displacement pump
assembly ....................................................... 30-99
Installation of variable displacement pump
assembly ..................................................... 30-101
Hydraulic pump assemblies ............. 30-102
Removal of the two hydraulic pump
assemblies .................................................. 30-102
Installation of hydraulic pump assembly ..... 30-103
Turbocharger assembly .................... 30-104
Removal of the turbocharger ....................... 30-104
Installation of the turbocharger .................... 30-104
Quick-attach coupler assembly ........ 30-105
Removal of quick-attach coupler
assembly ..................................................... 30-105
Installation of quick-attach coupler
assembly ..................................................... 30-106
Steering cylinder assembly .............. 30-107
Removal of steering cylinder assembly ....... 30-107
Installation of steering cylinder assembly .... 30-108
Lift cylinder assembly ....................... 30-109
Removal of lift cylinder assembly ................ 30-109
Installation of lift cylinder assembly ............. 30-110
Dump cylinder assembly ................... 30-111
Removal of dump cylinder assembly .......... 30-111
Installation of dump cylinder assembly ....... 30-112
Replacing windows in driver’s cab .. 30-113
Stuck glass .................................................. 30-113
Installation ................................................... 30-115
Door and side windows ............................... 30-116
30-2 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Comments
Comments
Chapter 30 contains descriptions, illustrations and diagrams,
which may vary according to the type of machine and equipment
variants concerned.
Over and above this, the illustrations and diagrams may also
contain optional extras and auxiliary equipment that are also
available.
NOTE
An illustration representing a particular way of handling some-
thing does not necessarily represent the machine part's actual
state. In other words, parts may be shown that, according to the
assembly instructions, should have been removed beforehand.
Similarly, parts may not be shown that should actually still be
mounted on the machine.
Weight dimensions/fluid capacities

In cases of any deviations to weight dimensions and fluid capac-
ities resulting from the different machine types, the minimum and
maximum values for the weight or the fluid capacity for the part
to be dismantled are given.
The exact details for the corresponding type of machine can be

found in the Weight or Lubricants Table contained in chapter 10.
WA90-5 / WA100M-5 30-3

Starter assembly DISASSEMBLY AND ASSEMBLY
Starter assembly
Removal of starter assembly

parking brake!
• Remove the earth lead from the (-) pole of the battery, or
throw the battery master switch if one has been installed!
1. Electrical cables
Remove the two cables (1) and (2) from the starter.
2. Fastening screws 
Loosen the two fastening (3) screws and remove the starter.
4 Starter: 4.7 kg
30-4 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Starter assembly
Installation of starter assembly

• To fit the starter carry out the removal procedure in reverse
order.
 Two screws (3): 98 - 122.5 Nm
WA90-5 / WA100M-5 30-5

Alternator assembly DISASSEMBLY AND ASSEMBLY
Alternator assembly
Removal of alternator assembly

parking brake!
1. Electrical connections
Disconnect the two cables (1) and (2).
2. Support and belt drive

a. Slacken off the fastening screw/nut (3).
b. Slacken off the adjusting screw (4) and move the alter-
nator towards the engine.
c. Remove the V-belt from the alternator's V-belt pulley.


d. Remove the fastening screw (3) and the respective

nuts.
e. Remove the adjusting screw (4) and take the alternator

out.
30-6 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Alternator assembly
Installation of alternator assembly

• To fit the alternator carry out the removal procedure in re-
verse order.
• Adjust the V-belt.
★ See chapter 20 TESTING AND ADJUSTING "V-belt ten-

sion" on page 20-17.
WA90-5 / WA100M-5 30-7

Water pump assembly DISASSEMBLY AND ASSEMBLY
Water pump assembly
Removal of water pump assembly

parking brake!
1. Draining the coolant 

See Operation Manual: COOLING SYSTEM, CHANGING
THE COOLANT AND CLEANING THE SYSTEM.
6 Coolant:13 l
2. Making assembly accessible

a. Remove the radiator assembly.
See chapter 30 DISASSEMBLY AND ASSEMBLY "Re-
moval of radiator assembly" on page 30-25.
b. Remove the V-belt.

See chapter 30 DISASSEMBLY AND ASSEMBLY "Re-
moval of alternator assembly" on page 30-6.
3. Alternator
Unscrew the alternator fastening screw (1).
4. Thermostat
a. Unplug the thermocouple’s (2) plug-type connector.
b. Unscrew the thermocouple (2) from the water pump.
5. Lines
Loosen the clamps (3) and (4) from the hoses and remove
the lines from the pump.
6. Heater line (option)

Disconnect the heating line (5) if supplied.
30-8 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Water pump assembly
7. Mounting
Unscrew the two fastening screws (7) and (8) and remove
the water pump.  10
4 Water pump: 7.4 kg 9
8. Gaskets and washers

Dispose of the gasket (10) and the O-ring (9). 
WA90-5 / WA100M-5 30-9

Water pump assembly DISASSEMBLY AND ASSEMBLY
Installation of water pump assembly

• To fit the water pump carry out the removal procedure in re-
verse order.
• Replace the gasket and the O-rings with new ones.
 Screw (7) and (8): 19 Nm
• Top the radiator up with coolant.

6 Coolant: 13 l
• Tension the V-belt.
See chapter 20 TESTING AND ADJUSTING "V-belt ten-

sion" on page 20-17.
30-10 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Engine cover assembly
Engine cover assembly
Removal of engine cover assembly

parking brake!
1. Preliminary work
Open the engine cover and secure it against falling down by
means of a support rod.
2. Engine cover
a. Remove two fastening screws (1) on both sides of the
mounting. 
b. Two people should then remove the engine cover.
4 Engine cover: 34 kg
WA90-5 / WA100M-5 30-11

Engine cover assembly DISASSEMBLY AND ASSEMBLY
Installation of engine cover assembly

• To fit the engine cover carry out the removal procedure in re-
verse order.
 Screws: 18 Nm
30-12 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Engine cover support assembly
Engine cover support assembly
Removal of engine cover support assembly

parking brake!
• Remove the engine cover.
See chapter 30 DISASSEMBLY AND ASSEMBLY "Removal

of engine cover assembly" on page 30-11.
1. Engine cover support

a. Remove the eight fastening screws (1) on both sides of
the cover support. 
b. Remove the cover support from the rear frame.
4 Engine cover support: 31 kg
4 Rear frame: 3.5 kg
Make sure when lifting that no other machine parts, in par-

ticular the radiator, are damaged.
WA90-5 / WA100M-5 30-13

Engine cover support assembly DISASSEMBLY AND ASSEMBLY
Installation of engine cover support as-

sembly
• To fit the engine cover carry out the removal procedure in re-
verse order.
 Screws: 18 Nm
30-14 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Engine assembly
Engine assembly
Removal of engine assembly

parking brake!
• Depressurise the hydraulic system: loosen the filler/vent
plug a few turns to relieve the pressure in the tank.

1. Cover plates
a. Unscrew the three screws (1) and remove the cover
plate from the battery compartment.
b. Unscrew the cap and disconnect both cables from the

battery.

6 Coolant: 13 l
3. Draining the engine oil 

See Operation Manual: ENGINE, CHANGING THE OIL
AND OIL-FILTER CARTRIDGE.
6 Engine oil: 9.5 l
4. Removing the radiator assembly

See chapter 20 TESTING AND ADJUSTING "Removal of
radiator assembly" on page 20-25.
WA90-5 / WA100M-5 30-15

Engine assembly DISASSEMBLY AND ASSEMBLY
★ Mark the cables in order to prevent flaws when recon-
necting. 
Disconnect all electrical cables from the engine (see the po-
sitions marked „e“).
6. Air cleaner
a. Loosen the clip (1) on the intake hose and a further clip
(2) on the intake manifold.
b. Unscrew the fastening screws (3) and (4) on the support

and remove the air cleaner.
30-16 WA90-5 / WA100M-5

7. Fuel supply lines
DANGER - Explosion hazard!

Leakage or evaporation of fuel might lead to an explosion.
Avoid any source of ignition such as open flames, ciga-
rettes or sparks. Close the fuel filter and the hoses immedi-
ately with a vent plug.
★ Mark the lines in order to prevent flaws when reconnect-

ing. 
a. Disconnect the two fuel supply lines (5) from the fuel fil-
ter.
b. Unscrew the two screws (6) and put the holder including
the relais box and the fuel filter aside.
c. Unscrew the fuel return line (7) from the fuel pump.

8. Brackets
a. Unscrew the screws of the brackets (8) and (9) from the
engine. 
b. Unscrew the two screws of bracket (10) from the engine.
★ Mark the hydraulic lines to make sure that they don't get
mixed up when being reconnected.
c. Disconnect all hydraulic lines from the hand pump.
★ Close the hydraulic lines immediately with a plug in or-

der to prevent the vapours from exiting and to prevent
any dirt and foreign particles from entering.
d. Unscrew the four screws of the bracket (11) and remove

the bracket.
e. Unscrew the four screws of the bracket (12) and remove

the bracket.
WA90-5 / WA100M-5 30-17

9. Variable displacement pump/hydraulic pump

Remove the variable displacement pump and the two hy-
draulic pumps. 
of variable displacement pump assembly" on page 30-99.
10. Engine governor

a. Unscrew the accelerator bowden cable (13) from the fu-
el injector pump.
b. Unscrew the two screws of the support (14) and remove

the support together with the accelerator bowden cable
from the engine.
11. Heating feed line

Unscrew the heating feed line (15) from the engine.
12. Engine support

a. Insert the hoist gear into the two contact lugs (16). 
b. Remove the engine's four fastening screws (17) at the

engine supports.  17
★ Make sure that all lines to the engine have been dis-
connected.
★ Place a collector tray below the engine to collect

any residual fluid which may drip out. 17
★ When lifting the engine out of its mount keep it bal-

anced and make sure that no other engine parts are
damaged.
c. Lift the engine slowly out of its support.
4 Engine: approx. 250 kg
30-18 WA90-5 / WA100M-5

12. Engine support

a. Insert the hoist gear into the two contact lugs (16). 
b. Remove the engine's four fastening screws (17) at the

engine supports.  17
★ Make sure that all lines to the engine have been dis-
connected.
★ Place a collector tray below the engine to collect

any residual fluid which may drip out. 17
★ When lifting the engine out of its mount keep it bal-

anced and make sure that no other engine parts are
damaged.
c. Lift the engine slowly out of its support.
4 Engine: approx. 250 kg
WA90-5 / WA100M-5 30-19

The tasks described below are to be carried out before the new
engine is installed, as some of the parts concerned are not part
of the replacement engine's delivery specification. In other
words, certain assemblies and parts that were mounted on the
old engine will be required when installing the new engine.
13. Clutch
of clutch assembly" on page 30-23.
14. Engine support

★ Mark the brackets to ensure that when the engine is in-
stalled again their position and installation location are
correct. 18
Unscrew 16 screws (18) and remove the engine's four sup-
port brackets. 
18
15. Contact lugs

Unscrew the four screws of the contact lugs (16). 
30-20 WA90-5 / WA100M-5

Installation of engine assembly

• To install the engine carry out the removal procedure in re-
verse order.
★ Before installing the engine, clean all the parts to be

mounted to it and remove any residual oil and dirt from
the engine compartment.
★ Before the new engine is installed in the machine, the

parts dismantled from the old engine have to be fitted
again.
• Replace the contact lugs that were delivered with the sup-
port (1).
• Make sure that the engine support is in the correct position

and installation location when screwing it back on.
 Screws: 45 Nm

1
 Screws: 280 Nm
★ When installing the engine make sure that no other engine

parts are damaged.
★ Make sure that the engine is correctly positioned and

aligned precisely.
• See chapter 30 DISASSEMBLY AND ASSEMBLY "Installa-

tion of variable displacement pump assembly" on page 30-
103.
 Screws: 280 Nm
• Tighten the screw (9) carefully (hollow screw).
• When reconnecting the hydraulic lines check that the mark-

ings coincide.
• When reconnecting the fuel lines check that the markings

coincide.
WA90-5 / WA100M-5 30-21

• When reconnecting the electrical cables check that the

markings coincide.
• Fill the engine up with oil. See Operation Manual:

CHANGING OIL UND OIL FILTER CARTRIDGE.
6 Engine oil: 9.5 l
• Fill the radiator up with coolant again.

See Operation Manual: COOLANT SYSTEM, CHANGING
6 Coolant: 13 l
• Check the hydraulic oil level and top up with oil if necessary.
Once finished you should vent the hydraulic oil tank. See
Operation Manual: HYDRAULICS, CHANGING OIL, VENT-
ING HYDRAULIC OIL TANK .
• Vent the hydrostatic travel gear and check the function:
Variable displacement pump and induction lines are filled

with oil.
• Open the filler pipe at the hydraulic tank.
• Start the engine and dump the bucket.
• Raise the lifting arm to its full extension upwards and tilt
the bucket fully.
• Let the engine continue to run and close the filler pipe
on the hydraulic tank.
• Lower the lifting arm to the ground and switch the en-
gine off.
• Check the oil level and top up with oil, if necessary.
• Finally, conduct a check of the seals and the various

functions.
• Check the engine speed.

See chapter 20 TESTING AND ADJUSTING "Engine RPM"
on page 20-18.
30-22 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Clutch assembly
Clutch assembly
Removal of clutch assembly

parking brake!
• Remove the variable displacement pump.

of variable displacement pump assembly" on page 30-101.
1. Clutch
a. Unscrew the clutch cover (1) from the flywheel housing. 3


4
b. Unscrew the clutch flange (2) from the flywheel.
c. Unscrew the screw (3) to remove the hub (4) from the
pump.
2
WA90-5 / WA100M-5 30-23

Clutch assembly DISASSEMBLY AND ASSEMBLY
Installation of clutch assembly

• To fit the clutch carry out the removal procedure in reverse
order.
• Clean the fastening screws for the flange and apply adhe-
sive to the screws.
 Loctite® 242 (blue) or Omnifit® 80M (red)
 Screws: 49 Nm
 Screws: 37 Nm
ING HYDRAULIC OIL TANK.
30-24 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Radiator assembly
Radiator assembly
Removal of radiator assembly

parking brake!
• Remove the engine cover. See chapter 30 DISASSEMBLY

AND ASSEMBLY "Removal of engine cover assembly" on
page 30-11.

See Operation Manual: COOLANT SYSTEM, CHANGING
6 Coolant: 13 l
2. Draining the hydraulic oil from the radiator 

See Operation Manual: HYDRAULIC SYSTEMS – CHANG-
ING OIL.
6 Hydraulic oil: 50 l

der to prevent vapours from exiting and to prevent any
dirt and foreign particles from entering.
3. Wiper
Disconnect all cables and hoses from the two wiper washer
containers (1).
4. Hydraulic hoses
a. Disconnect the three hydraulic hoses at the positions (2)
and (3) from the fan drive.
WA90-5 / WA100M-5 30-25

Radiator assembly DISASSEMBLY AND ASSEMBLY
b. Disconnect the hydraulic hose in position (3) from the

3 5
radiator stud.
c. Allow residual oil to flow out of the radiator.
d. Disconnect the hydraulic hose in position (4) from the

radiator stud.
5. Coolant hoses 4
a. Disconnect the hose (7) from the drain cock. 6
b. Disconnect the radiator's two hose lines (5) and (6).
6. Mounting
a. Suspend the radiator by means of a hoist.
b. Loosen the four fastening screws (8) for the brackets

that fix the radiator to the bottom of the frame. 
★ Make sure that all the lines and hoses to the radiator
have been disconnected.
★ Make sure that when the radiator is being lifted out

of its support that no other part of the machine is
damaged.
c. Lift the radiator assembly slowly out of the engine com-

partment.
4 Radiator assembly: 41 kg
30-26 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Radiator assembly
Installation of radiator assembly

• To fit the radiator carry out the removal procedure in reverse
order.
★ Before installing the radiator, remove any residual oil

and dirt from the engine compartment.
• Make sure that the fan is not damaged in any way when re-
placing the radiator.
 Screws: 115 Nm
• Fill the radiator up with coolant again. See Operation Manu-

al: COOLANT SYSTEM, CHANGING THE COOLANT AND
CLEANING THE SYSTEM.
6 Coolant: 13 l
• Fill the hydraulic tank with oil again and check the hydraulic
oil level.
Correct the oil level if necessary. Once finished you should

vent the hydraulic oil tank. See Operation Manual: HY-
DRAULICS, CHANGING OIL, VENTING HYDRAULIC OIL
TANK.
WA90-5 / WA100M-5 30-27

Fan assembly DISASSEMBLY AND ASSEMBLY
Fan assembly
Removal of fan assembly

parking brake!
1. Radiator
Unscrew the four fastening screws (1) to get access to the
back side of the fan.
2. Fan
Unscrew the nut (2) from the hydraulic engine and remove
the fan. 
30-28 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Fan assembly
Installation of fan assembly

• To fit the fan and pulley carry out the removal procedure in
reverse order.
 Screw: 35 - 45 Nm
WA90-5 / WA100M-5 30-29

Main brake cylinder assembly DISASSEMBLY AND ASSEMBLY
Main brake cylinder assembly
Removal of main brake cylinder assembly

parking brake!
1. Hydraulic lines
mixed up when being reconnected. 
a. Disconnect the hydraulic lines (1) and (2) from the main
brake cylinder.
★ Close the lines immediately with a plug in order to pre-

vent vapours from exiting and to prevent any dirt and
foreign particles from entering.
b. Disconnect the plug (3) from the main brake cylinder.
2. Brake pedal
Release the threaded rod's fork head (4) from the brake
pedal. 
3. Main brake cylinder

Unscrew the two fastening screws (5) and remove the cylin-
der. 
30-30 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Main brake cylinder assembly
Installation of main brake cylinder assem-

bly
• To fit the main brake cylinder carry out the removal proce-
dure in reverse order.
 Screws: 35 Nm
• Check the setting dimension on the main brake cylinder.
★ See chapter 20 TESTING AND ADJUSTING "Inch

valve – basic adjustment" on page 20-31.
★ Set the brake pedal angle to 45° and the distance

between the cylinder and the rod to a maximum of
1.5 mm.
• Ventillate and fill the brake circuit as follows:
1. Connect the ventillation device to port (1) of the front axle.
2. Open port (2) on the opposite side of the front axle.
★ provide a tray to collect leaking oil
3. Open the bleeding plug of the pump
4. Signal a second person to press the brake pedal and keep it

pressed.
5. After ventillation of the brakes and the inching line is com-

pleted, close port (2) of the front axle.
1
6. Close the bleeding plug of the pump.
7. Signal the second person to release the brake pedal.
8. Ventillate the the hoses to the expansion tank. 2
9. Fill the brake circuit with hydraulic oil.
10. Check the setting dimension on the main brake cylinder (see
above).
★ Set the brake pedal angle to 45° and the distance

between the cylinder and the rod to a maximum of
1.5 mm.
WA90-5 / WA100M-5 30-31

Priority valve assembly DISASSEMBLY AND ASSEMBLY
Priority valve assembly
Removal of priority valve assembly

parking brake!
1. Hydraulic lines
★ Mark the three hydraulic lines (1), (2) and (3) to make
sure that they don't get mixed up when being reconnect-
ed. 
Disconnect the hydraulic lines (1), (2) and (3) from the prior-
ity valve.
★ Close the lines immediately with a plug in order to pre-

2. Mounting
Unscrew the four fastening bolts (4) and remove the priority
valve.
1
★ Take care not to loose the O-ring (5).
2
5
3
4
30-32 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Priority valve assembly
Installation of priority valve assembly

• To fit the priority valve carry out the removal procedure in re-
verse order.
• When reconnecting the lines make sure that the markings

coincide.
WA90-5 / WA100M-5 30-33

Orbit-roll-valve assembly DISASSEMBLY AND ASSEMBLY
Orbit-roll-valve assembly
Removal of orbit-roll-valve assembly

parking brake!
1. Cover
Remove the six fastening screws (1) and remove the cab's
centre cover.
2. Hydraulic lines
★ Mark the hydraulic lines to make sure that they don't get 3
mixed up when being reconnected.  2
Unscrew all five hydraulic lines (2) to (6) from the orbit-roll- 6
valve.
★ Close all hoses immediately with a plug in order to pre-

4
5
30-34 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Orbit-roll-valve assembly
3. Orbit-roll-valve
Remove the four fastening screws (7) and withdraw the
orbit-roll-valve downwards and away from the steering
column's gearing.

4 Steering valve: 6.5 - 7 kg
WA90-5 / WA100M-5 30-35

Orbit-roll-valve assembly DISASSEMBLY AND ASSEMBLY
Installation of orbit-roll-valve assembly

• To fit the orbit-roll-valve carry out the removal procedure in
reverse order.
• Grease the gearing before reinstalling the steering valve.
 Screws: 30 Nm

coincide.
30-36 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Counterweight assembly
Counterweight assembly
Removal of counterweight assembly

parking brake!
1. Cover plates
a. Unscrew the three screws (1) and remove the cover
plate from the battery compartment.
b. Unscrew the cap and disconnect both cables from the

battery.
c. Unscrew the battery holder and remove the battery.
2. Rear lights
Disconnect the electrical plug-type connectors XM6 on the
left-hand side (2) and XM7 on the right-hand side (3).
3. Counterweight
a. Screw the two eye bolts (M20) into the threaded holes
(4) from above into the counterweight.
b. Suspend the counterweight by means of hoisting gear.
c. Unscrew the four fastening bolts (5) and lower the

counterweight to the ground. 
★ When lifting make sure that the load is properly bal-

anced.
4 Counterweight: WA 90-5: 1090 kg

WA 100M-5: 1275 kg
WA90-5 / WA100M-5 30-37

Counterweight assembly DISASSEMBLY AND ASSEMBLY
Installation of counterweight assembly

• To fit the counterweight carry out the removal procedure in
reverse order.
 Screws: 560 Nm
30-38 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Main control valve assembly
Main control valve assembly
Removal of main control valve assembly

• Raise the bucket to its highest position, dump the bucket
completely and suspend the boom with a support.
• Switch the engine off and actuate the parking brake!
1. Compartment
Unscrew the four screws and open the compartment in the
front frame.
2. Hydraulic lines
DANGER of crushing!
When you disconnect the hydraulic lines, the boom will
lower. Secure the boom with a support before you discon-
nect the hydraulic lines.
Unscrew all hydraulic lines (14 in all) from the main control
valve.

3. Main control device

Unscrew the three fastening screws (1) under the front
frame and lift the main control valve out of the machine.
4 Main control valve: 15 kg
WA90-5 / WA100M-5 30-39

Main control valve assembly DISASSEMBLY AND ASSEMBLY
Installation of main control valve assembly

• To fit the main control valve carry out the removal procedure
in reverse order.
 Screws: 35 Nm

coincide.
• When reconnecting the lines vent the six PPC hydraulic

lines one after the other as follows:
• Make sure the boom ist suspended from hoisting gear!

• Tilt the bucket completely!
a. Start the engine to recharge the PPC pressure accumu-

lator.
b. Stop the engine.
c. Remove one of the six PPC hydraulic lines from the

control valve and place a tray under the hydraulic line to
collect leaking hydraulic oil.
d. Operate the PPC that corresponds to the removed hy-

draulic line for approx. 20 s.
Front side of control valve Back side of control valve
Hydraulic Hydraulic
line color Operation line color Operation
indication indication
green lift yellow lower
red dump blue tilt
white open brown close
e. Reconnect the hydraulic line to the control valve.
f. Repeat the steps a to e for the other five PPC hydraulic

lines.
30-40 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Pilot valve assembly
Pilot valve assembly
Removal of pilot valve assembly

parking brake!
1. Cover
Unscrew the screws (1) and remove the cover.
Disconnect the pilot valve's plug-type connector (2).
3. Hydraulic lines
Unscrew all the hydraulic lines (3) (8 in all) from the pilot
valve.
★ Close all hoses immediately with plugs in order to pre-

vent the vapours from exiting and to prevent any dirt and
4. Pilot valve
a. Unscrew the four screws (2). 
b. Pull the rubber collar up and unscrew the four fastening

screws (3) and remove the pilot valve. 
4 Pilot valve assembly: 25 kg
WA90-5 / WA100M-5 30-41

Pilot valve assembly DISASSEMBLY AND ASSEMBLY
Installation of pilot valve assembly

• To fit the pilot valve carry out the removal procedure in re-
verse order.
 Screws: 35 Nm
 Screws: 35 Nm

coincide.
• When reconnecting the lines vent the six PPC hydraulic

lines one after the other as follows:
Tilt the bucket completely!
a. Start the engine to recharge the PPC pressure accumu-

lator.
b. Stop the engine.
c. Remove one of the six PPC hydraulic lines from the

control valve and place a tray under the hydraulic line to
collect leaking hydraulic oil.
d. Operate the PPC that corresponds to the removed hy-

draulic line for approx. 20 s.
Front side of control valve Back side of control valve
Hydraulic Hydraulic
line color Operation line color Operation
indication indication
green lift yellow lower
red dump blue tilt
white open brown close
e. Reconnect the hydraulic line to the control valve.
f. Repeat the steps a to e for the other five PPC hydraulic

lines.
30-42 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Monitor assembly
Monitor assembly
Removal of monitor assembly

parking brake!
1. Monitor housing
a. Remove the steering wheel.
b. Unscrew the two fastening screws (1) under the monitor

housing.
c. Unscrew the four fastening screws (2), remove the

bracket and lift the bellows to get access to the steering
column.
d. Unscrew the bolt (3) from the handle (5) and remove the
bolt (3), the spring (4) and the handle (5).
e. Unscrew the bushing (6), and remove the bushings (7)

and (8), the three discs (9) and the positioner (10).
★ When removing the positioner (10) prevent any part

from falling into the steering column. 
f. Slightly lift and incline the housing so that the electrical

cables underneath the monitor are visible.
★ When handling the monitor housing do not use ex-

cessive force to pull the cables out.
Disconnect the three plugs (12).
3. Monitor
Unscrew the four fastening screws (11) and take the monitor
out of its housing.
WA90-5 / WA100M-5 30-43

Monitor assembly DISASSEMBLY AND ASSEMBLY
Installation of monitor assembly

• To fit the monitor carry out the removal procedure in reverse
order.
• When inserting the positioner (10) prevent any part from fall-
ing into the steering column.
• The three discs (9, see previous page) must be inserted be-
tween the two parts (15) and (16).
• The positioner’s nose (13) must fit in the notch (14).
30-44 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Articulated joint assembly
Articulated joint assembly
Removal of articulated joint assembly

parking brake!
1. Articulated joint
★ Support the articulated joint and mark its installation po-
sition before loosening the bolted connections. 
a. Remove the bolted connections (1) between the articu-

lated joint and the transfer gear. 
b. Remove the bolted connections (2) between the articu-

lated joint and the front axle. 
c. Remove the articulated joint.
4 Articulated joint: 11 kg
WA90-5 / WA100M-5 30-45

Articulated joint assembly DISASSEMBLY AND ASSEMBLY
Installation of articulated joint assembly

• To fit the articulated joint carry out the removal procedure in
reverse order.
• When reinstalling the articulated joint make sure that the in-
stallation position lines up with the markings.
• Align the universal joints to each other.

• Tighten the bolts in a crosswise pattern.
 Screws: 70 Nm
30-46 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Variable motor assembly
Variable motor assembly
Removal of variable motor assembly

parking brake!
• Remove the articulated joint.

of articulated joint assembly" on page 30-45.
1. Draining the hydraulic oil from the radiator 

See Operation Manual: HYDRAULIC SYSTEMS – CHANG-
ING OIL.

★ Mark the connectors in order to prevent flaws when re-
connecting. 
Disconnect the two connectors (1) from the solenoids.
3. Hydraulic lines
mixed up when being reconnected. 
a. Disconnect the two travel hydraulic lines (2) and (3) from
the pipes.
b. Unscrew the hose line (4) which leads from the hydrau-
lic oil tank to the variable motor.
c. Only 35 km/h version: Unscrew the hose line (5) leading

from the variable displacement pump to the variable mo-
tor.

WA90-5 / WA100M-5 30-47

Variable motor assembly DISASSEMBLY AND ASSEMBLY
4. Variable motor 6
a. Support the variable motor by means of a jack and se-
cure the motor against falling to the ground. 4
★ Unscrew the four fastening bolts (6) and remove the 1

variable motor. 
4 Variable motor: 47 - 64 kg 3
2 5
6
30-48 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Variable motor assembly
Installation of variable motor assembly

• To fit the variable motor carry out the removal procedure in
reverse order.
Grease the toothing before remounting the variable motor.
 Screws: 115 Nm


coincide.
• Vent the hydrostatic travel gear and check the function:
Variable displacement pump and induction lines are filled

with oil.
the bucket fully.
• Lower the lifting arm to the ground and switch then en-
gine off.
• Finally conduct a check of the seals and the various

functions.
WA90-5 / WA100M-5 30-49

Rear axle assembly DISASSEMBLY AND ASSEMBLY
Rear axle assembly
Removal of rear axle assembly

rolling away and jack-knifing! Move the bucket to the
transport position, switch the engine off and apply the
parking brake.
• Danger of tipping over! Make sure that the machine can-
not tip over when being lifted up.
• Removing and/or installing the rear axle has to be per-

formed by two people!
1. Raising the rear end

a. Slide a jack from the rear into the centre position below
the rear axle and place a block of hardwood between
the jack and the rear axle.
The jack's load-bearing capacity must be at least 3000 kg!
b. Raise the machine so that the rear wheels are lifted ap-
proximately 15 cm off the ground.
c. Place a supporting chock or a block of hardwood under

the left and right-hand sides of the machine's rear end.
The chock's load-bearing capacity must be at least 3000 kg!
d. Lower the machine slowly to the ground and make sure

that the rear end rests safely on the support chocks.
30-50 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Rear axle assembly
e. Lower the bucket to the ground.
2. Wheels
★ Make sure that the wheels cannot tip over when being
removed.
a. Unscrew the wheel nuts (1). 
b. Two people should then remove the wheel from the rear
axle.
4 Wheel: 110 - 120 kg
• Carry out the same procedure on the opposite side of the

machine.
• Remove the articulated joint. See chapter 30 DISASSEM-

BLY AND ASSEMBLY "Removal of articulated joint assem-
bly" on page 30-45.
3. Variable motor
a. Support the variable motor and secure it against falling
to the ground.
b. Unscrew the four fastening bolts (2) and remove the

variable motor from the transfer gear. 
c. Leave the variable motor attached to the rear frame and

fasten it so that the rear axle dismantling process is not
inhibited in any way.
4 Variable motor: 47 - 64 kg
4. Axles
a. Slide the jack under the rear axle at the centre and
place a block of hardwood between the jack and the ax-
le. Make sure that the jack is tightly pressed up against 1
the axle.
b. Unscrew the 8 tightening screws (1) 
c. Lower the rear axle together with the transfer gear slow-
ly to the ground and then withdraw the entire axle from
underneath the machine.
4 Rear axle with transfer gear: 310 - 345 kg

1
WA90-5 / WA100M-5 30-51

Rear axle assembly DISASSEMBLY AND ASSEMBLY
Installation of rear axle assembly

• To fit the rear axle carry out the removal procedure in re-
verse order.
 Screws: 560 Nm
 Screws: 115 Nm
 Nuts: 400 - 450 Nm
• Bleed the brake system. See chapter 30 DISASSEMBLY

AND ASSEMBLY "Installation of main brake cylinder assem-
bly" on page 30-31.
30-52 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Front axle assembly
Front axle assembly
Removal of front axle assembly

rolling away and jack-knifing! Lower the bucket, switch
the engine off and apply the parking brake.
• Danger of tipping over! Make sure that the machine can-
not tip over when being lifted up!
• Removing and/or installing the rear axle has to be per-

formed by two people!
• Remove the articulated joint. See chapter 30 DISASSEM-

BLY AND ASSEMBLY "Removal of articulated joint assem-
bly" on page 30-45.
• Remove the disc brake. See chapter 30 DISASSEMBLY

AND ASSEMBLY "Brake disc group" on page 30-56.
1. Raising the front end

a. Press the bucket down onto the ground so that the ma-
chine's front wheels lift approximately 15 cm off the
ground.
b. Place a supporting chock or a block of hardwood on the

left and right-hand sides of the machine's front end.
2. Wheels
★ Make sure that the wheel cannot tip over when being re-
moved.
a. Unscrew the wheel nuts. 
b. Two people should then remove the wheel from the rear
axle.
4 Wheel: 110 - 120 kg
• Carry out the same procedure on the opposite side of

the machine.
WA90-5 / WA100M-5 30-53

Front axle assembly DISASSEMBLY AND ASSEMBLY
3. Axles
a. Slide the jack under the front axle at the centre and
place a block of hardwood between the jack and the ax-
le. Make sure that the jack is tightly pressed up against
the axle.
b. Unscrew the stirrup bolts located on both sides of the

axle. 
c. Lower the front axle together with the transfer gear

slowly to the ground and then withdraw the entire axle
from underneath the machine.
4 Front axle: 312 - 345 kg
30-54 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Front axle assembly
Installation of front axle assembly

• To fit the front axle carry out the removal procedure in re-
verse order.
 Stirrup bolts: 800 Nm
 Wheel nuts: 400 - 450 Nm
WA90-5 / WA100M-5 30-55

Front axle DISASSEMBLY AND ASSEMBLY
Front axle
Brake disc group
Disassembly
1. Unscrew the bolts (4).
2. Remove the brake caliper (5) from the support (10) and from
the brake disc (7).
3. Remove the snap ring (6).
4. Remove the brake disc (7).
30-56 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Front axle
6. Unscrew the bolts (9).
7. Remove the brake caliper support (10).
8. Only if necessary remove the dowel pin (11).
9. Remove the seal ring (12).
NOTE
This is a destructive operation for the seal ring.
WA90-5 / WA100M-5 30-57

Front axle DISASSEMBLY AND ASSEMBLY
Assembly
1. Assemble the seal ring (12) into the brake caliper support
(10) with special tool CA715476.
2. Before matching worked surfaces, make sure they are per-

fectly clean.
3. Degrease and clean with appropriate detergents.
4. Spread a film of grease on the contact surface of the brake

caliper support and the differential support (2).
 Loctite® 510 Superbond® 529
Check that the dowel pin (11) is in its seat.
5. Assemble the brake caliper support (10) with the bolts (9).
6. Tighten the bolts (9).
 60 Nm
7. Insert the snap ring (8) on the pinion end.
8. Assemble the brake disc (7).
9. Assemble the snap ring (6).
30-58 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Front axle
10. Assemble the brake caliper (5) on the support (10) with the
fastening bolts (9).
11. Apply sealant on fastening bolts (9).
12. Tighten the bolts (9).
 190 Nm
13. Check the brake caliper correct running blowing 5 bar pres-
sure air into the hole (a1).
Warning: never apply the brake lever (a2) during brake cali-
per assembly.
WA90-5 / WA100M-5 30-59

Brake caliper DISASSEMBLY AND ASSEMBLY
Brake caliper
All checking the disassembly and assembly instructions have
been taken from the brake caliper manufacturer manual of CAR-
RARO. KOMATSU is not responsible for any change made by
the manufacturer.
Hydraulic principle of operation

When the brakes are applied, hydraulic pressure acts on the
brake piston (10) moving it in the direction indicated by arrow “D”
and causing the pad to be applied to the disc (8).
While increased pressure ensures harder braking, it also results,

above a predetermined threshold, in the actuation of the auto-
adjust-mechanism as follows:
when washer (II) bears on thrust ball bearing (12), it causes ad-
justing nut (13), mounted on threaded rod (14), to rotate while
rod rotation is prevented by pusher (15) and lever (6).
At the same time, coil spring (24), attached to the brake piston
(10), is unwound a little, allowing the adjusting nut to rotate. The
mechanical brake (parking brake), actuated through lever (6), is
thus automatically adjusted each time the footbrake is applied. WARNING: UPDATE IN PROCESS!
30-60 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Brake caliper
Differential position
Compensation of parking brake auto-adjustment basic principle
Aim: To maintain constant adjustment of parking brake linkage

by increasing distance “d” to match pad wear. Above a certain
predetermined pressure, the hydraulic forces acting on the pres-
sure faces of differential piston (16) are out of balance, causing it
to move. Since the cross-section of face S2 is larger than that of
face SI, the piston moves in the direction of arrow “F”. The piston
(16) compresses elastic washers (17), relaxing the force acting
on adjusting nut (13), thus avoiding any risk of over-adjustment
due to caliper deflection of the compressibility of the pad friction
material.
Mechanical principle of operation

When the parking brake is applied, lever (6) acts on pusher (15)
and threaded rod (14), causing adjusting nut (13) to come into
contact with brake piston (10). At the same time, the opposing
(winding) force of coil spring (24) prevents the nut from rotating.
Brake pad (9A) is applied directly to the disc (8) while the reac-
tion force causes the calliper to slide sideways on its guide so
pad (9B) also bears on the disc. The parking brake is thus “on”.
As soon as the parking brake is released, and cable tension re-
duced, lever (6) is returned to its original position as a result of
the relaxation of the elastic washers (20).
Caliper removal
1. Disconnect the electrical pad wear indicator leads.
2. Remove the safety clip.
3. Press down on the calliper and drift out the retaining pin.
4. Disconnect the parking brake cable.
5. Disconnect the flexible hose from the inlet port.
6. Rotate the calliper about the guide.
7. Slide the calliper off the guide.
WA90-5 / WA100M-5 30-61

Disassembly (calliper removed)

1. Remove the piston dust cover.
2. Using a square-section tool (10 mm on a side) as indicated,

unscrew the piston until it rotates freely.
3. Place a piece of wood between the piston and the calliper.

Eject the piston from the calliper body by gradually applying
compressed air to the inlet port. If the piston is to be reused
take special care not to damage or dirty it. Clean only with
unused LHM mineral brake fluid.
4. Extract the seal from its groove using a smooth, round-

edged tool.
Under no circumstances should the internal piston compo-

nents be disassembled.
Disassembly
1. Remove the dust cover protecting the parking brake assem-
bly.
2. Clean all grease off the assembly.
4. Fit an extractor by sliding the legs into the grooves normally

intended for the lip of the parking brake assembly dust cov-
er.
5. To compress the cover and the spring, use special tool

CA715755 (a1).
6. Screw the extractor bolt (a2). Remove the cam shaft (2).
7. Remove the extractor and the special tool.
30-62 WA90-5 / WA100M-5

8. Remove the pusher (3).
9. Unscrew the threaded rod (4).
10. Remove the threaded rod (4), the helical spring (5) and the
cover (7).
11. Remove the O-ring (6) from the threaded rod (4).
12. Clean the caliper body and seal groove, then dry with com-
pressed air.
WA90-5 / WA100M-5 30-63

Assembly
1. Apply grease to the various parts of the assembly, and most
particularly to the bore receiving the threaded rod.
NOTE
Use grease supplied with the Service Kit or unused LHM fluid.
2. Assemble a new O-ring (6) on the threaded rod (4).
3. Assemble the threaded rod (4), the helical spring (5) and the
cover (7) on the brake caliper.
4. Screw the threaded rod (4).
5. Place the threaded rod (4) and the cover (6) as shown in fig-
ure to allow the cam shaft (2) insertion.
6. Grease the pusher (3).
7. Place the pusher into its seat.
8. Fit an extractor by sliding the legs into the grooves normally

intended for the lip of the parking brake assembly dust cov-
er.
9. To compress the cover and the spring, use special tool

CA715755 (a1). Screw the extractor’s bolt (a2).
30-64 WA90-5 / WA100M-5

10. Screw the piston with a wrench to further compress the

spring (5).
11. Insert the cam shaft (2).
12. Verify that the pusher (3) is in its seat.
13. Lock the cam shaft (2) with the snap ring (1).
WA90-5 / WA100M-5 30-65

Caliper reassembly
1. Dip the new piston seal into unused LHM fluid, then in-
sert it into the groove in the cylinder body.
2. Using clean LHM fluid, lubricate the cylinder bore and

piston. Insert the piston into the bore.
3. Push the piston home while rotating. This operation is

facilitated by using a special tool (as illustrated).
4. Screw the piston home. Rotate the piston until the slot
is perpendicular to the yoke when the calliper is locked
in position, i.e. with the air vent and bleedscrew in line
with each other.
5. Apply mineral grease to the inner surface of the dust

cover then fit to cylinder body.
Before attempting to use the parking brake, it is essential to

bleed the hydraulic circuit and depress the footbrake pedal
several times in order to move the pads to their normal op-
erating positions.
Replacement of guide protective covers

1. Do not remove the guide sleeve from the yoke.
2. Remove the complete protective covers with the bond-

ed collars.
3. Remove grease. Replace the guide bushes (2).
4. Using a mallet and a tube with an inside diameter a little

under 24 mm, fit the new protective covers (1).
5. Liberally smear the parts with the grease supplied in the

sachet.
6. Slide the calliper onto the guide sleeve (3), then insert
the lips of the protective covers into the grooves at each
end of the sleeve.
30-66 WA90-5 / WA100M-5

Pad replacement
1. Disconnect the electrical pad wear indicator leads.
2. Remove the safety clip (1).
3. Press down on the calliper and drift out the retaining pin
(2).
4. Rotate the caliper about the guide.
5. Remove the brake pads. Screw the piston fully down

(using a special tool).
6. Rotate the piston until the slot is perpendicular to the

yoke when the calliper is locked in position, i.e. with the
air vent and bleedscrew in line with each other.
7. Fit the new pads, making sure to place the pad with the
lug on the piston side.
8. Fit the new anti-clog pin (3) supplied with the Service
Kit.
9. Rotate the calliper and check that the lug on the pad fits
correctly into the slot in the piston.
10. Push the calliper back to its normal position.
11. Fit the retaining pin and safety clip.
12. Feed the pad wear indicator leads through the anti-clog
pin.
13. Reconnect the pad wear indicator leads.
14. Depress the footbrake pedal several times to move the

pads to the normal operating position.
WA90-5 / WA100M-5 30-67

Brake group - wheel shaft
Disassembly
1. Drain the oil completely from the axle beam.
2. Remove the short half shaft (1) from the wheel shaft.
3. Remove the brake bleed plug (20).
4. Unscrew and remove the wheel shaft retaining bolts (19).
Warning: do not drop the wheel shaft; if necessary use a

sling to hold it.
5. Remove the wheel shaft (2) carefully, making sure neither

the brake disc (13) nor the brake disc carrier (15) drop out.
6. With a lever remove the counterplate (14) from the axle

beam.
7. Remove the brake disc (13) and the brake disc carrier (15).
8. If necessary, remove the snap ring (16) inside of the brake

disc carrier (15).
30-68 WA90-5 / WA100M-5

9. Unscrew and remove the screw of the self-adjust kit (11) and
of the brake mechanism return kit (12).
10. Remove the relevant components.
11. Check the operating and wear conditions of the kit compo-
nents (11) and (12).
12. In order to extract the brake piston (8), use the hydraulic
connection applying the lowest oil or air pressure necessary
to dislodge the piston.
Warning: this operation must be performed with extreme

care.
13. Collect the quadrings (7) and (9) from the brake piston (8).
14. Remove the three split pins (9) of the brake piston with a
hammer and a punch.
WA90-5 / WA100M-5 30-69

15. Remove the seal ring (6) with a lever.
16. Turn the wheel shaft. Position the wheel shaft on a flat sur-
face and remove the bushing (5) using a suitable drift and a
hammer.
17. Remove the long half shaft (18) from the axle housing (17).
30-70 WA90-5 / WA100M-5

Assembly
1. Force the bushing (5) into the wheel shaft with the special
tool CA715649 and a hammer.
2. Turn the wheel shaft. Assemble the seal ring (6) into the
wheel shaft with the special tool CA715025 and a hammer.
3. Assemble the split pin of the self-adjust kit (11) in the brake
piston, using the special tool CA715752.
4. Clean the piston and the seat of the Quad-rings.
5. Grease the Quad-ring seat.
6. Insert and grease the Quad-rings (7) and (9).
7. Position a flat disc on the piston.
8. With a lever anchored to an eyebolt, exert a pressure just

enough to insert the piston into the wheel shaft.
Warning: do not damage the Quad-rings.
WA90-5 / WA100M-5 30-71

9. Collect the components of the self-adjust kit (11) and the pis-
ton return kit (12).
10. Install them into the piston as shown in the picture.
11. Tighten the fastening screws of the kits to the prescribed

torque.
 10 Nm
12. Assemble the counterplate (14).
13. Fit the long half shaft (17) into the axle beam (18).
14. Check that the snap ring (16) is already assembled into the
brake disc carrier (15).
15. Assemble the brake disc.
Warning: check that the brake disc pin (10) is towards the
bottom (see picture).
30-72 WA90-5 / WA100M-5

16. Before matching surfaces, make sure they are perfectly

clean. Degrease and clean with appropriate detergents.
17. Spread a film of sealant on the contact surface between the

axle beam and the wheel shaft.
 Loctite® 510 / Superbond® 529
NOTE
Check that the dowel pins (10) are in their seats.
18. Position the wheel shaft (2) on the axle housing and tighten
the retaining bolts (19) to the requested torque.
 190 Nm
19. Assemble the breather (20) and top up the oil.
 8 - 12 Nm
20. Assemble the short half-shaft (1) into the wheel shaft.
WA90-5 / WA100M-5 30-73

Rear axle DISASSEMBLY AND ASSEMBLY
Rear axle
Trunnions group and flange
Disassembly
1. Unscrew the fastening screws (1) and remove the cover with
seal ring (2).
NOTE
3. Remove the bush (4) from the differential support.
4. Remove the thrust washer (5).
5. Unscrew the bolt (11) and remove the support (14).
6. Remove the bush (10) and the bush (9).
NOTE
This is a destructive operation for the seal ring. Remove the
thrust washer (7).
30-74 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Rear axle
Assembly
1. Apply grease to the thrust washer (7) surface on the axle
beam side. Assemble the thrust washer (7).
2. Heat the bush (9) to 110 - 120 °C then assemble it to the dif-
ferential support.
NOTE
If necessary assemble the bush (9) with a pad and a hammer.
Warning: observe safety instructions.
3. Apply sealant on bushes (13) contact surface.
4. Assemble the bushes (13) to the rear support (14) with a

pad and a hammer.
5. Assemble the bush (10) in the rear support (14).
Warning: align the bush hole with the fastening bolt (13)
hole.
6. Assemble the bolt (13) and the nipples (12) and tighten
them to the prescribed torque.
7. Assemble a new seal ring (8) well lubricated into the front
support (14) with the special tool CA715031.
8. Insert the front support (14) on the axle beam (6).
WA90-5 / WA100M-5 30-75

9. Place the washer (5) on the differential support.
10. Heat the bush (4) to 110 - 120 °C then assemble it to the dif-
ferential support.
NOTE
If necessary assemble the bush (4) with a pad and a hammer.
Warning: observe safety instructions.
11. Assemble a new seal ring (3) into the cover (2) with the spe-
cial tool CA715476. Apply prescribed sealant on the cover.
12. Assemble the cover with seal ring.
13. Screw the fastening screws.
 12 Nm
30-76 WA90-5 / WA100M-5

Epicyclic reduction gear group
Disassembly
1. Drain the oil completely from the epicyclic reduction gear.
2. Unscrew and remove the two fastening bolts (3) of the plan-
etary carrier (1) with a wrench.
3. Remove the planetary carrier (1) from the wheel hub and
collect the relative O-Ring (4).
4. Position the planetary carrier (1) on a workbench and check

its wear conditions.
5. If required, replace the planetary gears (7) as follows:

6 9 10
a. remove the snap rings (10) from every pin (5);
b. remove the thrust washers (9); 8
c. remove the planetary gears (7) from the pins (5); 7
d. collect the needle bearings (6) and (8) checking their

conditions.
1
WA90-5 / WA100M-5 30-77

Assembly
1. Collect all epicyclic reduction gear parts: the planetary carri-
er (1), the snap ring (10), the thrust washer (9), the planetary 6 8 10
gear (7) with the needle bearings (6) and (8).
9
NOTE
With new planetary gears (7) it is advisable to assemble new nee- 7
dle bearings (6) and (8).
2. Position the planetary carrier (1) on a workbench.
NOTE
Grease well the needle bearings (6) and (8).
3. Insert the needle bearings (6) and (8) in the epicyclic gears
(7).
4. Fit the epicyclic gears (7) to the planetary carrier (1) pins.
5. Insert the thrust washer (9) and the snap rings (10) to the
planetary carrier (1) pins.
6. Assemble a new O-Ring (4) on the planetary carrier (1).
7. Assemble the epicyclic reduction gear on the wheel hub.
8. Assemble the screws (3) and tighten them.
 25 Nm
9. Top up the oil on the wheel hub.
10. Fit the oil plug (2) on the planetary carrier (1) and tighten it.
 60 Nm
30-78 WA90-5 / WA100M-5

Wheel hub
Disassembly
1. Slide the half-shaft from the axle beam. Unscrew and re-
move the fastening bolts (1) from the wheel carrier group.
2. In order to remove the wheel carrier group from its housing,

screw at least two of the just removed bolts (1) in the thread-
ed extraction holes.
3. Remove the wheel carrier (4) together with the ring gear (3).
4. Only if necessary, remove the centering bushes (2) of the

wheel carrier with a hammer and the special tool CA715655.
5. Remove the lock ring (5).
6. Remove the wheel hub (7), using levers and a hammer to

facilitate the operation.
NOTE
Collect the bearing cone (6).
7. Position the wheel hub (7) on a flat surface and remove the
seal ring (10) with a lever.
NOTE
8. Remove the bearing cups (6) and (9) using a hammer and a
drive.
WA90-5 / WA100M-5 30-79

9. To unscrew and replace worn-out hub studs (8), use a nut

and a lock nut on the studs, first heating the area where they
are positioned.
10. Remove the bearing cone (9) from the wheel shaft end using
a suitable extractor.
30-80 WA90-5 / WA100M-5

Assembly
The special operation “Set Right“ of the bearings does not re-
quire preload or backlash adjustment. Anyway, before assem-
bling new components check the indicated dimensions.
C C
A = 08.450 - 08.500 mm
A
B = 54.775 - 54.825 mm
C = 23.072 - 23.173 mm B
1. Heat the bearing (9) to 80 - 100 °C (176 - 212 °F).
2. Assemble the bearing cone on the wheel shaft end.
Caution! Wear safety gloves!
3. Apply the prescribed sealant on the threads and tighten the

studs (8) to the prescribed torque using two nuts (nut and
lock nut).
4. Position the wheel hub (7) on a workbench and force the two
bearing cups (6) and (9) in position with the special tool
CA715026 under a press or with a hammer.
5. Insert the seal ring (10) into the wheel hub with the special
6. Assemble the wheel hub (7) on the wheel shaft.
7. Heat the bearing (6) to 80 - 100°C (176 - 212°F).
8. Assemble bearing cone.
Warning: wear safety gloves
9. Position the wheel carrier (4) on a workbench and force the

bushes (2) to the carrier surface level with the special tool
CA715655. At least two bushes (diametrically-opposed)
should be set slightly higher than the carrier surface level to
be used as dowel pins.
WA90-5 / WA100M-5 30-81

10. Preassemble the wheel carrier (4) and the epicyclic ring
gear (3) with the locking ring (5).
3
11. Assemble the wheel carrier group (3), (4) and (5) on the
wheel hub using the two projecting bushes (2) as dowel
pins.
12. Force all hub dowel bushes (2) completely with the special
13. Assemble the wheel carrier (4) fastening bolts and tighten to
the requested torque. Assemble the short half-shaft.
30-82 WA90-5 / WA100M-5

Wheel shaft
Disassembly
1. Drain the oil completely from the axle beam.
2. Remove the short half shaft (1) from the axle beam.
3. Remove the seal ring (2) with a lever.
NOTE
4. Remove the long half shaft (5) with the splined sleeve (3)
from the axle housing with a threaded puller M10x1.5
screwed in the hole in the long half shaft.
5. Collect the splined sleeve (3).
6. Remove the sleeve inner snap ring (4) if replacement is re-

quired.
7. If necessary, extract the bush (6) using a suitable puller.
WA90-5 / WA100M-5 30-83

Assembly
1. Fit the bushing (6) into the axle housing with the special tool
CA715981 and a hammer.
2. Assemble the snap ring (4) on the splined sleeve (3).
3. Assemble the splined sleeve (3) to the long half shaft and to
the short half shaft (1).
4. Insert the long half shaft (5) with the splined sleeve (3) and
the short half shaft (1) on the axle beam (7).
5. Remove the short half shaft (1).
6. Assemble the seal ring (2) into the wheel shaft with the spe-
cial tool CA715087 and a hammer.
7. Assemble the short half-shaft (1) into the axle housing (7).
30-84 WA90-5 / WA100M-5

Differential support group
Disassembly
1. Drain the oil completely from the differential.
2. Loosen and remove the bolts (2)
NOTE
To remove the differential (1), screw two bolts into the threaded
lift-out bores of the differential carrier, then tighten.
Warning: support the differential support with a rope or oth-

er appropriate means.
3. Loosen and remove the screws (6) to remove the two ring
nut retainers (5). 5
6
4. Before removing bolts, mark halfbridles and the differential

carrier with permanent reference marks to avoid inverting
them when reassembling the unit.
5. Mark the area between the ring nuts (3) and (7) and the dif-
ferential carrier (1) as well.
6. Unscrew the adjuster ring nuts (3) and (7) using tools
11
CA119030 (a1) and a wrench.
7 3
7. Loosen and remove the 4 screws (11) and remove the 2 10
half-collars (10).
8. Check that the bushes (9) remain in their housings. 9

a1
WA90-5 / WA100M-5 30-85

9. Remove the differential housing (13).
10. The bearing cups (4) and (8) are removed together with the 13
differential housing. 8
4
Warning: do not invert the bearing cups if they are not go-
ing to be replaced.
Assembly
1. Assemble the bearings cups (4) and (8) on the differential
group (1) with pins and locking differential sleeve, (only for
CA150021).
4
8
1
Warning: do not invert the bearing cups if the bearings are
not replaced.
2. Position the complete differential housing (13) on the differ-

ential support (1). At the same time insert the differential 13
locking fork into the sleeve, (only for CA150021).
Warning: check the right side of the bevel crown assembly.
3. Move the differential group so to place the bevel crown gear

on the pinion. 11
4. Check that all bushes (9) are in their housings and position 10
both half collars (10) on their seats using the previously
traced reference marks.
9
5. Lock both half collars with their fastening bolts (11).
6. Assemble the adjusting ring nuts (3) and (7) to the differen-
tial support.
7. Tighten both ring nuts (3) and (7) with special tools 7
CA119030 (a1), till the backlash is eliminated and the differ-

ential bearings are slightly preloaded.
3
8. Check that the differential bearings are well settled; if neces- a1
sary, knock slightly with a soft hammer, in order to properly

set the bearings in position.
30-86 WA90-5 / WA100M-5

9. Position a magnetic-base dial gauge on the differential sup-

port, so that the feeler stylus touches the surface of one
tooth of the crown gear with a 90° angle.
10. Lock the pinion and move the crown gear alternatively and
note the pinion-ring gear backlash, measured with the com-
parator.
11. Repeat the operation on two or more points (teeth), rotating

the crown gear to obtain an average value.
12. Check if the measured backlash value is within the request-

ed range: 0.10 - 0.15 mm.
13. Set the bevel gear set backlash by turning adjusting rings
(3.7) with the appropriate tool CA119030.
14. Adjust the ring nuts, remembering that:

A A
(A): If the measured backlash is greater than the given toler-
ance range, unscrew the ring nut (3) and screw in the
adjuster ring nut (7) by the same measure;
B B
(B): If the measured backlash is less than the given toler-
ance range, unscrew the adjuster ring nut (7) and screw
in the adjuster ring nut (3) by the same measure.
15. After pinion-ring gear backlash adjustment, check that there

is a minimum preloading on the differential box bearings.
16. Repeat the whole sequence of the above mentioned opera-

tions till the indicated conditions are reached.
17. Once the pinion-ring gear backlash has been established,

measure the total preloading (T) of the bearings (pinion-ring
gear system), using a dynamometer whose cord is wound
on the end of the pinion.
The measured value should be within the following range:

T = (P + 2.9) - (P + 4.4) daN (WA90-5)
T = (P + 3.1) - (P + 4.7) daN (WA100M-5)
where P is the preloading effectively measured on the pin-
ion.
Warning: all the preloadings must be measured without the

seal ring.
WA90-5 / WA100M-5 30-87

If the measurement is not within the requested range, check

well the assembly of each component and operate on the A A
adjusting ring nuts (3) and (7) of the differential support:
If the total preloading is less than the given range, screw in

both adjuster ring nuts (3) and (7) by the same measure, B B
keeping the pinion-ring gear backlash value unchanged (A);
If the total preloading is greater than the given range, un-

screw both adjuster ring nuts (3) and (7) by the same mea-
sure, keeping the pinion-ring gear backlash (B) value
unchanged.
18. Tighten the bolts (11) of both half collars to the requested
torque.
19. Check bearings total preload (T).

See previous page.
20. Once all the adjustment operations have been completed, fit
the adjuster ring nut retainers (5) and their respective
screws (6), tightening them to the requested torque.
21. Before matching surfaces, make sure they are perfectly

clean.
22. Degrease and clean with appropriate detergents.
23. Spread a film of sealant on the contact surface between the

axle beam and the differential carrier.
24. Check that the dowel pins (12) are in their seats.
30-88 WA90-5 / WA100M-5

25. Position the differential carrier (1) on the axle housing and
tighten the retaining bolts (2).
 169 Nm
26. Top up the oil.
WA90-5 / WA100M-5 30-89

Bevel gear marking test

• To test the marks of the bevel gear teeth, paint the ring gear
with red lead paint. The marking test should be always car-
ried out on the ring bevel gear teeth and on both sides.
OK: Correct contact: If the bevel gear is well adjusted, the Z

OK
mark on the teeth surfaces will be regular.
Z: Excessive contact on the tooth tip: Approach the pin-

ion to the ring bevel gear and then move the ring bevel
gear away from the pinion in order to adjust the back-
lash. X
X: Excessive contact at the tooth base: Move the pinion

away from the ring bevel gear and then approach the
ring bevel gear to the pinion in order to adjust the
backlash.
Movements to correct:
1. Move the pinion for type X contact adjustment.
2. Move the pinion for type Z contact adjustment.
30-90 WA90-5 / WA100M-5

Differential locking group

Disassembly
Solo per / Only for
CA150021
1. Remove the differential group before disassembling the dif-

ferential locking device.
2. Unscrew the bolts (16) and remove the cylinder support

(15).
3. Collect the piston (13) and the O-rings (14) and (12). 16
12
13
14
15
4. Remove the lock ring (11) preventing the bush (10) from be-
ing pushed out by the spring (9).
9
10
Danger: possible ejection of the bush (10) and spring (9).
11
5. Remove the bush and the spring from the control shaft (3).
6. Remove the bolt (1) and the cover (2) keeping the bush (4)
from being pushed out by the spring (5). 2 1
4
5
6
Danger: possible ejection of the bush (4) and spring (5).
7. Remove the bush, the spring and spacer (6) from the control
shaft (3).
8. Remove the control shaft (3), then collect the lock ring (7)
and the fork (8).
WA90-5 / WA100M-5 30-91

Assembly
1. Place the differential support on a workbench.
2. Assemble the lock ring (11) in the housing at the end of the
control shaft (3).
8
3. Insert the spacer (10) and the spring (9) on the control shaft
(3).
3
4. Insert the shaft in the differential support and in the fork (8),
respecting for each element the shown position.
5. Assemble the new O-ring (12) to the piston (13).
6. Insert the piston (13) at the ends of the shaft.
7. Assemble the new O-ring (14) to the support (15).
8. Assemble the support (15) with the fastening screws (16). 16

12
9. Tighten the screws (16) to the requested torque. 13
 27.6 Nm
14
15
10. Insert the lock ring (7) on the control shaft (3) from the fork
side by pushing it in the housing with a pipe of suited dimen-
sion.
11. Insert the spacer (6), the spring (5) and the bush (4) on the
control shaft.
12. Apply sealant on the cover (2).
13. Assemble the cover (2), pushing the spring (5), with the fas-
tening screws (1).
Danger: possible ejection of the bush and the spring.
14. Tighten the screws to the requested torque.
 27.6 Nm
30-92 WA90-5 / WA100M-5

Differential group (100% Diff. Lock)
Disassembly
1. Remove the sleeve (13) and pins (11) from the differential
housing (12).
2. Lock the differential with a clamp.
3. Unscrew the fastening bolts (1) and remove the bevel gear
(3).
Warning: this will make both differential half housing (4 and

12) free, so take care not to drop the internal components.
4. Disassemble the two differential half housing (4 and 12).
5. Make alignment marks on the half boxes before splitting

them.
4
6. Disassemble all the components. Check the operating and
wear conditions of the components. 12
7. Remove the bearing cones (2) from the half boxes (4 and
4
12) using a standard extractor. 2
2
12
WA90-5 / WA100M-5 30-93

Assembly
1. Assemble the bearing cones (2) on the half housing (3 and
10), using the special tool CA119230 and a hammer. 4 2
12
2. Position a half housing (4) on a workbench and assemble all

inner components (locking differential counterdiscs (5), sun
gears (9 and10), spiders (8), spider gears (7), thrust wash-
ers (6)), as shown in the picture.
3. Join the two half boxes, aligning the reference marks made
during disassembly.
4. Before matching surfaces, make sure that they are perfectly

clean, degrease and clean them with appropriate deter-
gents.
5. Place the bevel gear (3) on the differential housing.
6. Apply sealant on the threads and tighten the bolts (1) to the
requested torque.
 Loctite® 270 or Superbond® 331
 95 Nm
7. Insert the pins (11) into their seats.
8. Assemble the sleeve (13) on the differential housing (12).
Warning: take care to assemble it in the correct position.
30-94 WA90-5 / WA100M-5

Differential group (LSD 25%)
Disassembly
1. Lock the differential with a clamp. Unscrew the fastening
bolts (1) and remove the bevel gear (2).
Warning: this will make both differential half boxes (4) and
(12) free, so take care not to drop the internal components.
2. Disassemble the differential box in two half boxes (4) and

(12) with the relative components.
3. Make alignment marks on the half boxes before splitting

them.
4. Disassemble all the components. Check the operating and

wear conditions of the components.
5. Remove the bearings cones (3) and (13) of the half boxes
4
(4) and (12), using two levers or a three-hold extractor.
13
3
12
WA90-5 / WA100M-5 30-95

Assembly
1. Assemble the bearing cones (3) and (13) on the half hous-
ings (4) and (12), using the special tool CA119230 and a 4 3
hammer.
12
13
2. Position a half housing (4) or (12) on a workbench and as-

semble all inner components (locking differential counter-
disks (5), locking differential discs (6) and (7), sun gears (8),
spiders (9), spider gears (10), thrust washers (11), as shown
in the picture.
NOTE
The first disc (7) must be assembled with friction material on the
discs side and the flat surface on the sun gear (8) side.
3. Join the two half boxes, aligning the reference marks made
upon them.
4. Position the bevel gear (2) on the half box (4).
5. Apply sealant on the thread and tighten the bolts (1).
 Loctite® 270 or Superbond® 331
 95 Nm
30-96 WA90-5 / WA100M-5

Pinion group
Disassembly
1. Lock the differential carrier in a vice.
2. Unscrew the lock nut (10) using special tools CA119099 and
CA7155022
NOTE
This is a destructive operation for the ring nut.
3. Tap the shaft with a soft hammer to remove the bevel pinion
(1).
Warning: take care not to drop the pinion.
4. Collect the washer (4) and (6), the collapsible spacer (5), the
bearing cone (8) and the retaining washer (9).
5. Remove the bearing cups (3) and (8) using a driver and a
hammer.
6. To remove the bearing cone (3) of the pinion (1), use a stan-
dard extractor.
7. Collect the bearing cone (3) and the underlying shim (2).
WA90-5 / WA100M-5 30-97

8. Check all pinion components for wear.
9. The ring nut (10) and the collapsible spacer (5) must be re-
placed when reassembling the unit.
Assembly
1. Fit the bearings cups (3) and (8) using the special tool
CA119225 and a hammer.
2. Prepare the kit consisting of the special tools called "false

pinion" (a1) CA715023 and "false differential box"
CA119182 (a2) and CA119206 (a3) and a depth gauge (a4).
3. Insert the bearing cones (3) and (8) in their seats.
4. Assemble the "false pinion" and its ring nut (10).
5. Tighten without exceeding the ring nut, till the backlash is

eliminated.
6. Install "false differential box" special tools into the differential

group support (7) and lock it with the half collars. See: next
figure.
30-98 WA90-5 / WA100M-5

7. Assembly diagram of the "false differential box" (on the left).
8. Use a depth gauge to measure distance (X) (distance be-

X
tween the axis of the differential bearings and the point at
which the pinion head is supported, or base of the bearing).
9. In order to determine the necessary thickness value (S) be-

tween pinion and bearing, subtract the value (V) stamped on V
pinion head (V = requested distance) from the measured

value (X).
10. Select the shim (2) of thickness valve (S) among the range
of available shims.
11. Remove the "false differential box" special tool from the dif-
ferential support (7).
12. Remove the ring nut (10), the "false pinion" and the bearing
cones (3) and (8).
6
13. Insert the chosen shim (2) with the chamfer against the gear 3 5
into the pinion shaft (1). 4
2
14. Force the bearing (3) into the pinion shaft (1) with the spe-
cial tool CA715082 under a press, making sure that it is well
set. 1
1
15. Insert the shims (4) and (6) and the new collapsible spacer
(5).
16. Always use a new collapsible spacer (5).
17. Insert the bevel pinion (1) unit into the differential support
8
housing (7) and the bearing cone (8) into the pinion end, as
shown in the picture.
1
18. Use the special tool CA715179 and a hammer to drive the
bearing (8).
7
WA90-5 / WA100M-5 30-99

19. Insert the ring nut washer (9) and screw a new lock ring nut
(10) on the pinion end.
20. Screw the ring nut (10) in, using the wrench for ring nut
CA119099 and for pinion retainer CA715022.
Warning: The torque setting is given by the preloading mea-

surement on bearings (3) and (8).
21. Tighten the ring nut (10) gradually. If the tightening is exces-
sive, the collapsible spacer (5) must be replaced and the
procedure repeated.
22. When you check the preloading, it is advisable to beat

slightly both pinion ends with a soft hammer, so as to help
setting the bearings (3) and (8).
P = 9.2 - 13.8 daN
23. Carry out the preloading measurement (P) of the pinion

taper roller bearings (3) and (8), using a dynamometer
whose cord is wound on the end of pinion spline (1).
24. The adjustment is carried out by increasing the ring nut (10)
torque gradually, being careful not to exceed.
Warning: all preloadings must be measured without the seal

ring.
25. Once the requested preloading value is achieved, caulk the

ring nut (10), using a hammer and a chisel.
30-100 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Variable displacement pump assembly
Variable displacement pump assembly
Removal of variable displacement pump

assembly
• Park the machine on a piece of level, solid ground and se-

cure it against rolling away and jack-knifing!
Lower the bucket, switch the engine off and put the park-
ing brake on.

• Remove both hydraulic pumps

of the two hydraulic pump assemblies" on page 30-104.
★ Mark the cables in order to ensure that they are not
Disconnect the two connectors (1) and (2) from the sole-
noids.
2. Hydraulic lines
★ Mark the lines in order to ensure that they are not mixed
up when being reconnected. 
a. Disconnect four hydraulic lines (3) to (6) from the vari-

able displacement pump.
3
★ Close the hydraulic lines immediately with a plug in
order to prevent vapours from exiting and to prevent
any dirt and foreign particles from entering. 4

a. Suspend the variable displacement pump from a hoist- 5
ing gear.
b. Remove the two fastening screws (7).  7
c. Pull the variable displacement pump forwards away

from the engine. 
★ The amount of space for removing the pump is very 6

limited. For this reason you should ensure that no
other machine parts are damaged when lifting and
WA90-5 / WA100M-5 30-101

Variable displacement pump assembly DISASSEMBLY AND ASSEMBLY
removing the variable displacement pump.
d. Lift the variable displacement pump out of the machine.
4 Variable displacement pump: 39 - 51 kg
30-102 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Variable displacement pump assembly
Installation of variable displacement pump

assembly
• To fit the variable displacement pump carry out the removal
procedure in reverse order.

• Grease the gearing before reinstalling the pump.
 Screws: 280 Nm


coincide.
• Variable displacement pump and induction lines are filled

with oil.
• Vent the hydrostatic travel gear and test the function:
the bucket fully.
• Lower the lifting arm to the ground and then switch off
the engine.
• Finally conduct a check of the seals and the various

functions.
WA90-5 / WA100M-5 30-103

Hydraulic pump assemblies DISASSEMBLY AND ASSEMBLY
Hydraulic pump assemblies
Removal of the two hydraulic pump as-

semblies
• Park the machine on a piece of level, solid ground and se-

cure it against rolling away and jack-knifing! Lower the
bucket, switch the engine off and put the parking brake
on.

• Remove the priority valve.

of priority valve assembly" on page 30-32.
1. Hydraulic lines
a. Disconnect the two hydraulic lines (1) and (2) from the
hydraulic pump.
★ Close the hydraulic lines immediately with a plug in

order to prevent vapours from exiting and to prevent
b. Remove the two fastening screws (3) and take the hy-
draulic pump off. 
4 Two hydraulic pumps: 8 kg
30-104 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Hydraulic pump assemblies
Installation of hydraulic pump assembly

• To fit the hydraulic pump carry out the removal procedure in
reverse order.
• Bleed the air from the hydraulic system.
 Screws: 70 Nm
WA90-5 / WA100M-5 30-105

Turbocharger assembly DISASSEMBLY AND ASSEMBLY
Turbocharger assembly
Removal of the turbocharger

1. Disconnect the hose (1) from the air filter.
2. Disconnect the hose (2) from the muffler.
3. Remove the four screws (3) from the muffler.
4. Disconnect the hydraulic hoses (4) and (5).
5. Close the hoses (4) and (5) with a plug. Do not spill the oil.
6. Disconnect the hose (6) leading to the intake manifold.
7. Remove the four nuts (7) of the turbocharger.
8. Remove the turbocharger.
Installation of the turbocharger

1. Carry out the removal procedure in reverse order.
NOTE
Insert a new seal between the turbocharger and the intake
manifold.
30-106 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Quick-attach coupler assembly
Quick-attach coupler assembly
Removal of quick-attach coupler assembly

• Prior to removing the quick-attach coupler the working
equipment must be disengaged. See the operating instruc-
tions.
2
• Unlock the quick-attach coupler and make sure that the con-
trol lever is set to lock position (2).
1
the engine off and apply the parking brake!
1. Hydraulic lines
Remove the locking rings (1) on both sides of the quick-at-
tach coupler system at the connecting block and withdraw
the angular part (2).

2. Rocker arm
Unscrew the locking bolt (3) and remove the bolt from the
rocker arm. 
3. Quick-attach coupler
a. Loosen the clamping screws (4) on the quick-attach
coupler's joint rod. 
b. Unscrew the bearing bushes (5) 
c. Use hoisting gear to lift the quick-attach coupler out of

the lifting arms.
4 Quick-attach coupler system: 135 kg
WA90-5 / WA100M-5 30-107

Quick-attach coupler assembly DISASSEMBLY AND ASSEMBLY
Installation of quick-attach coupler

assembly
• To fit the quick-attach coupler carry out the removal proce-
dure in reverse order.
• Tighten the bearing bushes as far as possible and then loos-

en the bolted connections by approximately half a rotation.
 Bolted connections: 280 Nm
• Danger of crushing! Use a rod to align the quick-attach

couplers.
• Danger of injury! Do not insert your fingers into any of the
holes!
 Screws: 70 Nm
30-108 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Steering cylinder assembly
Steering cylinder assembly
Removal of steering cylinder assembly

1. Hydraulic lines
3
★ Mark the hydraulic lines to make sure that they don't get 5

2
mixed up when being reconnected.
Disconnect the hydraulic lines (1) from the cylinder.

der to prevent vapours from exiting and to prevent any 4
dirt and foreign particles from entering. 1
2. Lubricant lines 6
Disconnect the lubricant line (2) from the cylinder.
a. Support the steering cylinder or suspend it from hoisting
gear.
b. Unscrew the locking screws (3) and (4). Remove the

bolts (5) and (6) from the front or rear frame,
respectively. 
★ Keep the distance washer and seals in a safe place

or, if they are worn, replace them with new ones.
c. Lift the steering cylinder up and out of the frame.
★ Make sure that when doing so the piston rod is not

damaged.
4 Steering cylinder: 13 kg
WA90-5 / WA100M-5 30-109

Steering cylinder assembly DISASSEMBLY AND ASSEMBLY
Installation of steering cylinder assembly

• To fit the steering cylinder carry out the removal procedure
in reverse order.
Danger of crushing! Use a rod to align the steering cylin-

ders. Never insert your fingers into any of the holes!
 Screws: 70 Nm
• When reconnecting the hydraulic lines make sure that the

markings coincide.
• Greasing
Grease the steering cylinders.
30-110 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Lift cylinder assembly
Lift cylinder assembly
Removal of lift cylinder assembly

• Lift the bucket to its highest position and secure it against
lowering.
• Switch the engine off and apply the parking brake!
★ The WA90-5 and WA100M-5 are equipped with two lift cylin-
ders.
1. Hydraulic lines
★ Mark the hydraulic lines (1) to make sure that they don't
get mixed up when being reconnected.  1
Disconnect the hydraulic lines from the lift cylinder. (If a hose
rupture safety device has been installed, disconnect it’s hy-
draulic lines too.)
★ Close the hydraulic lines immediately with a plug in or- 1

2. Lift cylinder
a. Suspend the lift cylinder from hoisting gear.
2
b. Unscrew the two locking screws (2) and remove the two 3
bolts (3) from the lifting rack or front frame, respectively.

★ Keep the distance washer and seals in a safe place 2

3
c. Lower the lift cylinder carefully with the hoisting gear

down to the ground or onto a jack.
★ Do not damage the piston rod.

4 Lift cylinder: 32 - 33 kg
WA90-5 / WA100M-5 30-111

Lift cylinder assembly DISASSEMBLY AND ASSEMBLY
Installation of lift cylinder assembly

• To fit the lifting cylinder carry out the removal procedure in
reverse order.
Danger of crushing! Use a rod to align the lifting cylinders.

Never insert your fingers into any of the holes!
 Screws: 70 Nm

markings coincide.
• Greasing
Grease the lifting cylinders.
30-112 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Dump cylinder assembly
Dump cylinder assembly
Removal of dump cylinder assembly

1. Hydraulic lines
mixed up when being reconnected.  1
Disconnect the hydraulic lines (1) from the cylinder. (If a

hose rupture safety device has been installed, disconnect its
hydraulic lines, too.)
★ Close the hydraulic lines immediately with a plug in or- 1

der to prevent the vapours from exiting and to prevent
2. Dump cylinder
a. Suspend the cylinder from hoisting gear. 2
3
b. Unscrew the two locking screws (2) and remove the two
bolts (3) from the rocker arm (4) or front frame, respec-

2 3
tively.
★ Keep the distance washer and seals in a safe place

c. Lift the dump cylinder with the hoisting gear up and out 4
of the frame.
★ Do not damage the piston rod.

4 Dump cylinder: 51 - 54 kg
WA90-5 / WA100M-5 30-113

Dump cylinder assembly DISASSEMBLY AND ASSEMBLY
Installation of dump cylinder assembly

• To fit the tilt cylinder carry out the removal procedure in re-
verse order.
Danger of crushing! Use a rod to align the tilt cylinders.

Never insert your fingers into any of the holes!
 Screws: 70 Nm

markings coincide.
• Greasing
Grease the tilt cylinder.
30-114 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Replacing windows in driver’s cab
Replacing windows in driver’s cab
Stuck glass

ing away and jack-knifing! Lower the bucket, switch the en-
gine off and apply the parking brake!
Preparation work for replacing the front window: 1 3 4 5

• Dismantle the front windscreen wiper (1).
a. Unscrew the wiper arm.
b. Remove the wiper axle and the motor.
• Dismantle the heating’s panelling (2) at the front.
Preparation work for replacing the rear window:

• Remove the exhaust pipe (5). 2
• Dismantle the rear window windscreen wiper (4).
a. Unscrew the wiper arm.
b. Remove the wiper axle and the motor.
• Disconnect the plug-type connector for the rear window

heater system (3).
Tools for reworking tasks:

• Wooden spatula for spreading the sealing compound (A).
A B
• Applicator for the prime coating (B)
• Nozzle for the sealing cartridge (C)
• Suction gripper (D)
• Cleaning cloths
• Knife
D C
• Masking tape
• Glue gun for the sealing compound cartridge
WA90-5 / WA100M-5 30-115

Replacing windows in driver’s cab DISASSEMBLY AND ASSEMBLY
Replacing a window:
★ The order numbers for the respective parts are listed in the
following table.
• Cut the glass out.

Make sure that a sealing strip (1) of at least 1 - 2 mm is left 1
around the frame.
• Remove the pane of glass.
• Cut away the sealing compound strip (2) from the door 2
frame to at least 1 - 2 mm.
• Use masking tape to mask the left and right-hand side ar-
eas.
• Clean the cab door's frame.
• Clean the frame and glass edge with the cleaner

BETACLEAN 3350.
• Wipe the area clean with a damp cloth.
• Apply the sealing compound to the frame with the

BETAPRIME 5402 applicator (B).
Allow to dry for at least 15 minutes. Max. 24 hours.
• Coat the glass edge (3) with activator cleaner BETAWIPE

VP 04604 and then wipe it down with a clean cloth.
• Use an applicator (B) to apply BETAPRIME 5001 to the

glass edge.
Allow to dry for at least 15 minutes. Max. 24 hours.

3
4
• Use the glue gun to apply BETASEAL 8000 to the frame's

designated area (5).
Processing temperature: 10° - 35° C
• Using two suction grippers insert the glass into position and
press slightly against it.
• Hold the glass in the correct position and apply the sealing
compound completely around the inside and outside of the
glass window's edge.
• Use adhesive tape to hold the glass firmly in place to the 5

cab.
Cure time: 24 hours
• Remove the masking tape after the glass sealant has dried.
30-116 WA90-5 / WA100M-5

DISASSEMBLY AND ASSEMBLY Replacing windows in driver’s cab
Spare Parts:
Pos. Name Order No. Qty.
1 Cleaner, frame Betaclean 3350 42U-56-H0P00 1
2 Cleaner, glasses Betawipe VP 04604 42U-56-H0P20 1
3 Primer, glass Betaprime 5001 42U-56-H0P19 1
4 Primer, frame Betaprime 5402 42U-56-H0P02 1
5 Sealer, cartridge (300 ml) Betaseal 8000 42U-56-H0P06 2 off
Installation
• To mount the wipers and the window heater systems carry
out the removal procedure in reverse order.
Rear window
a. Reconnect the plug-type connector for the rear window 1 3 4 5
heater system (3).
b. Reassemble the rear window windscreen wiper (4).
 Wiper axle screws (M18): 10 Nm
 Wiper arm screws (M8): 20 Nm
 Wiper motor screws (M8): 8 Nm
c. Reinstall the exhaust pipe (5)

2
Front window
a. Reassemble the heating’s panelling (2) at the front.
b. Reassemble the front windscreen wiper (1).
 Wiper axle screws (M24): 60 Nm
 Wiper arm screws (M8): 20 Nm
 Wiper motor screws: 60 Nm
WA90-5 / WA100M-5 30-117

Replacing windows in driver’s cab DISASSEMBLY AND ASSEMBLY
Door and side windows

★ Unscrew the door or the side window assembly from the
driver’s cab. Then disassemble the door and side windows
according to the scetches below.
Door window assembly
1 2
 1: 15 Nm  2: 15 Nm  3: 22 Nm
Side window assembly
 1: 15 Nm  2: 15 Nm
30-118 WA90-5 / WA100M-5

90 OTHERS
Hydraulic circuit diagram 1/3 . . . . . . . . . . . . 90-3
Wiring diagram1/5 . . . . . . . . . . . . . . . . . . . . . 90-9
Wiring diagram 2/5 . . . . . . . . . . . . . . . . . . . . 90-11
Wiring diagram 3/5 . . . . . . . . . . . . . . . . . . . . 90-13
Wiring diagram 4/5 . . . . . . . . . . . . . . . . . . . . 90-15
Wiring diagram 5/5 . . . . . . . . . . . . . . . . . . . . 90-17
Wiring diagram, Speed control . . . . . . . . . . 90-19
Wiring diagram, Immobilizer . . . . . . . . . . . . 90-21
WA90-5 / WA100M-5 90-1

others
90-2 WA90-5 / WA100M-5

Hydraulic circuit diagram 1/3
rechts
heben senken
Option: ALS G 1/2"
40
2,0 l
M18x1,5
44
92f 10f
Standard:
10g
ohne
Schlauch-Bruch-
6 5 4
Sicherung
G 1/2"
40 50a
M14x1,5(8L) 55a
92e
d=0,8 60a
G1/2"
1 2 3
40 64b 11e
68b links rechts
G 1/4"
41 50a
10e
E C2 M18x1,5 M18x1,5
9a 44 50a 50a 44
35g
G 1/2"
92h 40
8a
55d 6a
55a
D=60/32-369
D=60/32-369
V2 PIL G 3/8" G 3/8"
42a 42a
Option: ALS 50a
G1/2" G1/4"
40 41a 50d A B Kabine
50d
55a
65g 7a
72e 10d 10c
55a
M18x1,5
11d 11c M18x1,5 44
44
92k 92l
72b B A
35e
G 3/8" G 3/8"
42a 42a
Option: Schlauchbruchsicherung ohne ALS
Option: Schlauchbruchsicherung mit ALS

BOOM
M14x1,5
49b
Hubzylinder 35c
D=80/45-689 6 7
92m
M10x1
0,8
M22x1,5
35d 220 bar P 43 G 1/2"
40 40
G 1/2"
29 48 29
Option: 41b
M14x1,5 Option
Schlauchbruch- Standard:
35a
sicherung 72b ohne ALS 66a 71a 55b 50d
35b L R
50d
11b 11a M10x1
48
72e 10b 10a b1 heben (grün) d=1 3 91c
240 bar 240 bar
33a
320 bar
senken (gelb)
33b
a1
M16x1,5 (10L)
B1 55d 55d
G1/2" G1/4"
40 41a 50d
d=1
41a
V2 PIL A1 1 350
50d
92h 63a
G 1/4"
50a 55a Option:
35j 55d
Schlauchbruch-
b2 sicherung auskippen (rot) 4
32a
E C2
44
63 50a 32b
68b G1/2" a2 d=0,6
40 64b
M16x1,5 (10L)
d=0,8 B2
13a 13
d=4,2 d=1
M14x1,5(8L) 12a 12
50c A2 2
Standard: 320 bar
M18x1,5
ohne
10g Schlauch-Bruch-
Sicherung
b3 zu (weiß) 5
31a
M18x1,5 auf (braun)
44
31b
links 63 50a a3
M16x1,5 (10L)
heben senken B3 66a
43
Standard:
15
ohne ALS
320-160 ccm/U
71a
14
A3 T
18+4 bar 6 P T
90q
M22x1,5
55b 175 bar
35f T1
HDM19 91b G 1/4"
d=2,0
68a 61a
91d M16x1,5 (10L) P T LS
nur bei ALS 0,16 l

20 bar G 1/2" G 1/2" G 1/4"
40 40 40 41a
30d
G 1/2"
91g
Option: M18x1,5 Option
49a
100%
Diff.- M14x1,5
56c 41b 50d 55d
Sperre
G1/2" G1/4"
50a 40 41 30b 30c
M16x1,5(10L)
V2 PIL 91f M16x1,5(10L) M16x1,5(10L)
91e 50d
9
92g
C2
G1/2"
50a 40
4
5
72d
BUCKET
Kippzylinder
D=95/50-479 Fahrtrichtung
i ges = 26,41 = 18,6 x 1,42 (30km/h)
M18x1,5
44 Option: 100 % Diff.-Sperre
i ges = 41,48 = 18,6 x 2,23 (20km/h)
22b
r Rad dyn. = 0,512 m
auskippen 8 8b 3 50d M10x1
einkippen 48a
20km/h 30km/h
22d 22c 55d
34c
34d
3/8"
42a
M14x1,5
41b
92n A Option
M14x1,5
41b
22e
22a
56c
P B
Speisedruck = 30 bar (26 bis 30) 56b Option:
3/8" 3/8" M14x1,5 100%
50d 42a 42a 41b Diff.-
delta p = 430 bar (Druckabschneidung) Sperre
22 Arbeitsdruck (abs) = 460 bar = 430 + 30 M10x1

ca. 2,4-4,5bar 48a
34a 34b
Z HD-Ventil delta p = 460 bar 50d
max. Arbeitsdruck (abs) = 490 bar = 460 + 30

60c
M10x1
48a
G 1/2" G 1/2"
42 40 50a
60b
41b
EF
M14x1,5
M12x1,5
CF
55d MB 90p
b a a b
60c SAE 1" (20km/h)
G 1/4" SAE 1.1/4" (30km/h) B oben M1 A6VM107DA
41a 50d
20km/h
Ps Fa Fa1 Fe 90m 20 km/h
24b
B links LS 24
30km/h
A6VM160DA
Vg=56ccm/U P LK 35mm
bei 20 km/h G 1/4"
59a
20km/h 65 44
M18x1,5 U 90n 30 km/h
61a
SAE 3/4"
2350 U/min Vg=71ccm/U
70c 20km/h
30km/h 65g 43
M22x1,5 a
bei 30 km/h SAE 1" 90o
70e 50g 30km/h
Standard
15a
M22x1,5 (15L) M 32 8
Vg=11,6 ccm/U
A4VG56DA A4VG56EP bei 20 km/h
M14x1,5
61
90g 20 km/h 90h 20 km/h Vg=19,6 ccm/U
SAE 1.1/4" L
30km/h SAE 1" (20km/h)
SAE 1.1/4" (30km/h)
bei 30 km/h 70d 23
Standard: Option: GRA 23a

61
M14x1,5 30a
A4VG71DA A4VG71EP SAE 1"
20km/h A unten
14a M26x1,5 70 30km/h
30km/h 43a
R 90k 30 km/h 90l 30 km/h SAE 3/4"
17a 17 b
M22x1,5 70c 20km/h 20km/h 30km/h
20km/h 43b
T1
15b 65 T2 G
A rechts X3 X1 T
14c X1 X2 G S
M22x1,5 (15L)
M22x1,5 (15L)
56a
M22x1,5 M14x1,5 M33x2
Fs M12x1,5
60b
17b M18x1,5
44b 50b 20km/h
14b 43b 20km/h 20km/h 65f 41b 20km/h 64a 45a 20km/h
55d M26x1,5 M18x1,5 M42x2

MA 17c
50d 41b
M14x1,5 M26x1,5
43a 64h 30km/h
43a 30km/h 30km/h 65b 44 30km/h 47 30km/h
M18x1,5
44
14d
55 d=1,0 68 20km/h
P
60d d=1,4 68c 30km/h 30km/h 26c
M22x1,5 (15L)
19
92c LK 35mm
59a
19a
20km/h
nur bei 30km/h
92a
18 18a 26a
30km/h 20km/h T P
30km/h
27h M18x1,5
nur bei 20km/h 44
Option: Schnellwechsler elektr. 55c
15c 20km/h 27a
M22x1,5 (15L) 20km/h 55a
15d 50b 16 16b 27c

Lenkung / steering 21a 21
Standard LK 40mm
59b
30km/h 20km/h
20km/h 30km/h
55a (18L)
(18L)
55d
Arbeits-hydr./working hydr. (22L) 66a 71a 20km/h
M14x1,5
61 M18x1,5
42a
92q M18x1,5 50a 44

50a 44
26d
72c M26x1,5 LK 35mm
65d 43a A 59a
G3/8"
P
(28L)
G 1" 26e
45b 30km/h UNTEN
A B
Standard:
Diff.-Sperre
ohne 100%
30km/h
WA90-5
15e G 1"
G 1.1/4" 45 20km/h 92b
46a 27i M12x1,5
50c 49
14c OBEN
B1 A B2 75 T
G3/8"
M26x1,5 27e Option
Vorsteuergeraet
43a
71b 66b
3 bar
14f P1 20km/h
92d
42b
pilot valve
M22x1,5
43 LK 35mm
20 B 59a
M14x1,5 1a 1 27d
61 14e
30km/h 20km/h M18x1,5
64 44
M16x1,5(10L)
M22x1,5 (15L) P2 65d
27g
91h
0,5 2,0 50f 50f
0,03 0,35 Option: reversierbarer Lüfter
bar bar Saugschlauch DN38
M16x1,5(10L)
M16x1,5(10L)
bar bar M36x2(28L) M36x2(28L) 71b 66b
ca. 42 l Oel
ca. 16 l Luft
WA90-5 / WA100M-5 90-3

rechts
heben senken
Option: ALS G 1/2"
40
2,0 l
M18x1,5
44
92f 10f
Standard:
10g
ohne
Schlauch-Bruch-
6 5 4
Sicherung
G 1/2"
40 50a
M14x1,5(8L) 55a
92e
d=0,8 60a
G1/2"
1 2 3
40 64b 11e
68b links rechts
G 1/4"
41 50a
10e
E C2 M18x1,5 M18x1,5
9a 44 50a 50a 44
35g
G 1/2"
92h 40
8a
55d 6a
55a
D=60/32-369
D=60/32-369
V2 PIL G 3/8" G 3/8"
42a 42a
Option: ALS 50a
G1/2" G1/4"
40 41a 50d A B Kabine
50d
55a
65g 7a
72e 10d 10c
55a
M18x1,5
11d 11c M18x1,5 44
44
92k 92l
72b B A
35e
G 3/8" G 3/8"
42a 42a
Option: Schlauchbruchsicherung ohne ALS
Option: Schlauchbruchsicherung mit ALS

BOOM
M14x1,5
49b
Hubzylinder 35c
D=80/45-714 6 7
92m
M10x1
0,8
M22x1,5
35d 240 bar P 43 G 1/2"
40 40
G 1/2"
29 48 29
Option: 41b
M14x1,5 Option
Schlauchbruch- Standard:
35a
sicherung 72b ohne ALS 66a 71a 55b 50d
35b L R
50d
11b 11a M10x1
48
72e 10b 10a b1 heben (grün) d=1 3 91c
240 bar 240 bar
33a
340 bar
senken (gelb)
33b
a1
M16x1,5 (10L)
B1 55d 55d
G1/2" G1/4"
40 41a 50d
d=1
41a
V2 PIL A1 1 350
50d
92h 63a
G 1/4"
50a 55a Option:
35j 55d
Schlauchbruch-
b2 sicherung auskippen (rot) 4
32a
E C2
44
63 50a 32b
68b G1/2" a2 d=0,6
40 64b
M16x1,5 (10L)
d=0,8 B2
13a 13
d=4,2 d=1
M14x1,5(8L) 12a 12
50c A2 2
Standard: 320 bar
M18x1,5
ohne
10g Schlauch-Bruch-
Sicherung
b3 zu (weiß) 5
31a
M18x1,5 auf (braun)
44
31b
links 63 50a a3
M16x1,5 (10L)
heben senken B3 66a
43
Standard:
15
ohne ALS
320-160 ccm/U
71a
14
A3 T
18+4 bar 6 P T
90q
M22x1,5
55b 175 bar
35f T1
HDM19 91a G 1/4"
d=2,0
68a 61a
91d M16x1,5 (10L) P T LS
nur bei ALS 0,16 l

20 bar G 1/2" G 1/2" G 1/4"
40 40 40 41a
30d
G 1/2"
91g
Option: M18x1,5 Option
49a
100%
Diff.- M14x1,5
56c 41b 50d 55d
Sperre
G1/2" G1/4"
50a 40 41 30b 30c
M16x1,5(10L)
V2 PIL 91f M16x1,5(10L) M16x1,5(10L)
91e 50d
9
92g
C2
G1/2"
50a 40
4
5
72d
BUCKET
Kippzylinder
D=95/50-479 Fahrtrichtung
i ges = 31,12 = 20,14 x 1,545 (30km/h)
M18x1,5
44 Option: 100 % Diff.-Sperre i ges = 49,62 = 20,14 x 2,464 (20km/h)
22b r Rad dyn. = 0,546 m

auskippen 8 8b 3 50d M10x1
einkippen 48a
20km/h 30km/h
22d 22c 55d
34c
34d
3/8"
42a
M14x1,5
41b
92n A Option
M14x1,5
41b
22e
22a
56c
P B
Speisedruck = 30 bar (26 bis 30) 56b Option:
3/8" 3/8" M14x1,5 100%
50d 42a 42a 41b Diff.-
delta p = 430 bar (Druckabschneidung) Sperre
Arbeitsdruck (abs) = 460 bar = 430 + 30 M10x1

22 ca. 2,4-4,5bar 48a
34a 34b
Z HD-Ventil delta p = 460 bar 50d
max. Arbeitsdruck (abs) = 490 bar = 460 + 30

60c
M10x1
48a
G 1/2" G 1/2"
42 40 50a
60b
41b
EF
M14x1,5
M12x1,5
CF
55d MB 90p
b a a b
60c SAE 1" (20km/h)
G 1/4" SAE 1.1/4" (30km/h) B oben M1 A6VM107DA
41a 50d
20km/h
Ps Fa Fa1 Fe 90e 20 km/h
24b
B links LS 24
30km/h
A6VM160DA
Vg=56ccm/U P LK 35mm
bei 20 km/h G 1/4"
59a
20km/h 65 44
M18x1,5 U 90f 30 km/h
61a
SAE 3/4"
2350 U/min Vg=71ccm/U
70c 20km/h
30km/h 65g 43
M22x1,5 a
bei 30 km/h SAE 1" 90o
70e 50g 30km/h
Standard
15a
M22x1,5 (15L) M 32 8
Vg=11,6 ccm/U
A4VG56DA A4VG56EP bei 20 km/h
M14x1,5
61
90a 20 km/h 90b 20 km/h Vg=19,6 ccm/U
SAE 1.1/4" L
30km/h SAE 1" (20km/h)
SAE 1.1/4" (30km/h)
bei 30 km/h 70d 23
Standard: Option: GRA 23a

61
M14x1,5 30a
A4VG71DA A4VG71EP SAE 1"
20km/h A unten
14a M26x1,5 70 30km/h
30km/h 43a
R 90c 30 km/h 90d 30 km/h SAE 3/4"
17a 17 b
M22x1,5 70c 20km/h 20km/h 30km/h
20km/h 43b
T1
15b 65 T2 G
A rechts X3 X1 T
14c X1 X2 G S
M22x1,5 (15L)
M22x1,5 (15L)
56a
M22x1,5 M14x1,5 M33x2
Fs M12x1,5
60b
17b M18x1,5
44b 50b 20km/h
14b 43b 20km/h 20km/h 65f 41b 20km/h 64a 45a 20km/h
55d M26x1,5 M18x1,5 M42x2

MA 17c
50d 41b
M14x1,5 M26x1,5
43a 64h 30km/h
43a 30km/h 30km/h 65b 44 30km/h 47 30km/h
M18x1,5
44
14d
55 d=1,0 68 20km/h
P
60d d=1,4 68c 30km/h 30km/h 26c
M22x1,5 (15L)
19
92c LK 35mm
59a
19a
20km/h
nur bei 30km/h
92a
18 18a 26a
30km/h 20km/h T P
30km/h
27h M18x1,5
nur bei 20km/h 44
Option: Schnellwechsler elektr. 55c
15c 20km/h 27a
M22x1,5 (15L) 20km/h 55a
15d 50b 16 16b 27c

Lenkung / steering 21a 21
Standard LK 40mm
59b
30km/h 20km/h
20km/h 30km/h
55a (18L)
(18L)
55d
Arbeits-hydr./working hydr. (22L) 66a 71a 20km/h
M14x1,5
61 M18x1,5
42a
92q M18x1,5 50a 44

50a 44
26d
WA100M-5
72c M26x1,5 LK 35mm
65d 43a A 59a
G3/8"
P
(28L)
G 1" 26e
45b 30km/h UNTEN
A B
Standard:
Diff.-Sperre
ohne 100%
30km/h
15e G 1"
G 1.1/4" 45 20km/h 92b
46a 27i M12x1,5
50c 49
14c OBEN
B1 A B2 75 T
G3/8"
M26x1,5 27e Option
Vorsteuergeraet
43a
71b 66b
3 bar
14f P1 20km/h
92d
42b
pilot valve
M22x1,5
43 LK 35mm
20 B 59a
M14x1,5 1a 1 27d
61 14e
30km/h 20km/h M18x1,5
64 44
M16x1,5(10L)
M22x1,5 (15L) P2 65d
27g
91h
0,5 2,0 50f 50f
0,03 0,35 Option: reversierbarer Lüfter
bar bar Saugschlauch DN38
M16x1,5(10L)
M16x1,5(10L)
bar bar M36x2(28L) M36x2(28L) 71b 66b
ca. 42 l Oel
ca. 16 l Luft
WA90-5 / WA100M-5 90-5

left 13 right
rechts Cabine
heben senken
11 220 bar P
8
b1 heben (grün) d=1,0 3
320 bar L R
senken (gelb)
a1
240 bar 240 bar
B1
d=1,0
A1 1
BOOM
B2
320 bar
b2
a2
auskippen (rot)
einkippen (blau)
d=0,6
4
12 350
9
d=3,5 d=1,0
A2 2
320 bar
b3 zu (weiß) 5
auf (braun)
a3
B3
A3 T
18+4 bar 6 P T
320-160 ccm/U
T1
11 0,16 l
20 bar
21 14 P
185 bar
T LS
links
heben senken
direction
BUCKET
10
einkippen auskippen
17 16
ca. 2,4-4,5bar
Z
Fa
15
EF CF
MB
b a a b
B oben M1 A6VM107DA
Ps Fa1 Fe
90m 20 km/h
B left
LS
A6VM160DA
P
U 90n 30 km/h
a
M
32 8
20 19 A4VG56DA
20 km/h
Standard:
A4VG71DA
A4VG56EP
20 km/h
Option: GRA
A4VG71EP
7 A unten
R b
30 km/h 30 km/h
T1
T2
X1
5 X2 G S
A right
X3 X1 T G
6
Fs
MA
18 d=1,0 P
T P
steering
2
3 bar
working hydr.
(28L)
(35L)
B1 A B2
P1 4
3
pilot valve
P2 WA90-5
0,03
bar
0,35
bar
0,5
bar
2,0
bar M16x1,5(10L) WA100M-5
1
WA90-5 / WA100M-5 90-7
Wiring diagram 1/5
F1.1:E F1.1:E
30
F1.5:E F2.1:E F3.1:E
15
10A
10A
10A
10A
F2.3 F1.1 F2.1 F3.5
START
1BrR
1BrR
0.5BrW
0.5BrW
0.5RY
0.5RB
ON OFF
F N R +
C ACC BR R1 B S439 S261
1.5RW
6R
6R
6R
6R
1.5R
1.5R
km/h
0.3W
A19 H28 P21 H76 S43 H439.1 H439.2 H126 H379 P96 P25 H263 H30 H288 P384 H453
0.3G
0.3Y
0.3R
0.5WBr
0.5WB
h Q t ˚ mph
1.25W
1.25G
2R
2L
0 0 0 0 0 0 0 0 0 0 0 0
+12V GND E24 E34 E3 A28 A25 E21 E22 E13 E43 E1 GND E2 E35 E16 E11 E40 GND E9
Option 4 5
P426 Immobliser P426 0.8 P426
XJ15 15 14 4 12 10 1 4 5 XJ12 XL43 3 4 2 1 XL39 1 3 2 XJ15 6 5 3 XL27 2 4 3 1 sec XL27 5 6 XJ12 6 7 10 8 XJ15 2 7 1 XJ4 3 4 2
2 6 8
K167.2
0.5G
0.5WG
0.5BY
0.5G
0.5WBr
0.5GW
0.5LW
0.5W
0.5W
0.5GY
0.5RY
0.5YR
0.5G
0.5Y
0.5R
0.5Y
0.5B
0.5B
0.5BY
0.5G
0.5BW
0.5WL
0.5W
10R
10R
0.5RY
0.5BR
0.5Y
0.5Br
0.5G XL65 2 4 XL65 2 4
0.5BY
0.5B
WA65.5
1W WA70-5 WA90-5
WA80-5 WA100M-5
0.5YG
1LY
0.5G
0.5G
0.5Y
0.5Y
0.5GR 0.5RY
86 30 86 30 30 15
XS1 7 4 3 2 XS1 1 A B XS2 5 6 XS1 31

65¹ 65¹
XL65 1 3 XL65 1 3
V118.2 85 87 87a 85 87 87a 87 87a

1RY
1BR
1LY
0.5LY
1LY
10R
10R
K373.1 K373.2 K235
1Br
1B
1.5R
1.5R
V118.3 0.5W 0.5YG
6R 0.5GR
88 86 86 30 86 87
12¹ 92¹ 32¹
0.5RW
1W
0.5GY
0.5YG
0.5V
1G
0.5Y
0.5R
1Y
88a 85 85 87 85 30
K238 K158 K106
1B
XL54 (116)K385:86 (88)S316:5 (93)K314:6

4RW
25R
25R
16R
6 2 3 4 5 1 4 2 1 3 1 3 2
XL36 XL37
XL55
250A
100A
1W
0.5W
1G
1Y
0.5GY
0.5Y
0.5B
F5 F4
16R
25R 0.5B
XM1 3 4 XM1 1 12 V XL44 2 1 XM1 5 6 7 8 9 10 11 12 XM2 1 2 3 5 6 XM2 8 9 4

1.5R
92 Ah
1GW
1RW
1LW
1W
1W
1GY
G57
1YB
1YR
1V
1B
1B
1B
1B
1Br
1B
1Y
(123)F6:E 1LY
1WL
1LY
XM4 1 2 3 4 X452 1 2
25R
25R
1LY
50B
50R
1B
1B
52A
1 2 X97
19A
1 2 0.5¹ S 1 2 1 2
L IG
1GY
1LY
1B
1B
1Y
1Y
G 0.05¹ S
60A
7¹ M B
5.3 5.1
¹ ¹
3 t˚ p p Q
1Y
1B
2.2kW
U 2880W 1.9k¹/20˚C 0.065 bar 0.78 bar

1 2 1 2
G10 E B R12 Y320 M9 31 S58 Option S127 B262 B19 B304 B228
F R B13
5.3 5.3
¹ ¹ Y236.1 Y235
Q Q
25B
50B
16B
16B
1B
0.5B
0.5B
0.5B
0.5B
1B
1B
1B
1B
1B
>10¹ = FULL
R97 B452
Y236 Y237
31
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
Position next see Page 2
No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos.
S43 Key Switch 6 P21 Service Meter 3 K106 Relay Battery 7 XL... Connector Floor Frame Harness - H28 Control Lamp Alternator 3 B13 Sensor Cooling Watertemperat. 22
WA100M-5
S58 Battery Main Switch 8 P25 Cauge Cooling Watertemperature 23 K158 Relay Startermotor 6 XM... Connector Engine Harness - H30 Control Lamp Engine Oil Press. 25 - - -
WA90-5
S127 Switch Parking Brake 14 P96 Cauge Fuel Level 22 K167.2 Relay Timer 0.8 sec. 18 XF... Connector Front Frame Harness - H76 Control Lamp Preheater Engine 4 B19 Sensor Engine Oil Pressure 25 WA80-5
P384 Cauge Speed 27 - - - XJ... Connector Main Monitor - H126 Control Lamp Parking Brake 14 B228 Sensor Speed 27 WA70-5
S261 Switch Driving Range 20 P426 Main Monitor 2 K235 Relay Driving Range 20 XS... Connector Fuse - H263 Control Lamp Air Cleaner 24 B262 Sensor Air Cleaner 24 WA65-5
S439 Switch Drive Direction 14 K238 Relay Air Preheater Engine 4 F.. Fuse - H288 Control Lamp Brake Oil Level 26 B304 Sensor Brake Oil Level 26
Y236.1 Magnet Valve Synchron 18 K314 Switch Frequency ALS 26 SS... Joint Of Wires - H379 Control Lamp Driving Range 21 Y235 Magnet Valve Driving Range 20
G10 Alternator 2 K373.1 Relay Parking Brake Forward 14 - - - H439.1 Control Lamp Forward 13 Y236 Magnet Valve Forward 15
G57 Battery 8 R12 Air Preheater Engine 3 K373.2 Relay Parking Brake Reverse 16 - - - H439.2 Control Lamp Reverse 13 Y237 Magnet Valve Reverse 17
M9 Starter Motor 6 R97 Sensor Fuel Level 21 K385 Relay Backup Alarm 17 B452 Sensor Water-In-Fuel 28 H453 Control Lamp Water-In-Fuel 28 Y320 Magnet Engine Stop 5
WA90-5 / WA100M-5 90-9

Wiring diagram 2/5
Version Swizerland
F1.1:E
30
F2.4:E
15
20A
10A
10A
10A
10A
10A
10A
10A
1YB
1GY
F1.6 F1.4 F2.2 F3.4 F1.6 F2.4 F1.3 F1.2
1GW
1WR
1GW
1WR
1W
1GY
1BR
1RL
1V
XL10 3 0 0
1 0
I
1R
1R
8 6 2
I
7
1WB
58 5
2 4 1 1
30
1 8
49 49a H31 H29
6
G 5 3 2
p
1GW
56b 56a
0.5R
31 H 31 C E30 L R E33 5.0 bar
S331.3 K67 P426 S331.1 S331.2 P426 S70
XJ15 8 XJ12 2
1GB
1GrB
1GrR
10
1LB
1Gr
1L
1V
1V
7
H101 H51
S101 S51 E123 R246 2

0.5G 1GY
XL11 6 5 XL10 2 1 XL11 3 2 1 4
0.5GB
0.5G 0.5Y
1GW
0.5GB
0.5GB
0.5GB
1BY
1BY
1BR
0.5G
0.5G
1BY
0.5Y
1R
1WR
86 30 86 30
65¹ 65¹
XF1 7 XF1 5 XM3 6 7 XF1 6 XM3 9
85 87 87a 85 87 87a
K56.1 K56.2
0.5B
1GW
1GB
1GB
1W
1G
1G
1Y
1BY
3Ampere
Brücke 1Y
V118
1B
10A
10A
10A
10A
XF3 5 1 XF4 1 5 F2.5 F2.8 F2.7 F2.6
1RW
1GR
1GR
1GL
1GL
1RY
(127)E71:+
B8 E5 E6
XF1 1 4 3 2 XM3 1 2
1RW
1GR
1GL
1GL
1RY
1B
1GW
XM6 4 1 1 4 XM7 XM6 2 XM7 2 XM6 3 XM7 3

1BY 1BR
1B 1B
1RW
1RW
1GR
1GL
1RY
1RY
1GW
1GW
1GB
1GB
1GR
1GR
1B
1B
1B
1B 1B 1B XC4 + - XC5 + - XC6 - + XC7 - +

58L 58R 54 54
XF1 8 XF1 9 XF3 4 2 3 1 1 3 2 4 XF4
58 56b 56a 31 31 56a 56b 58

E68.2 E69.2 E68.1 E69.1 E68.3 E69.3 E3 E4 E60 E61
0.5B
0.5B
0.5B
0.5B
1B
1B
1B
1B
1B
1B
1B
E1 E2
31
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56
Position next see page 3
WA100M-5
No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos.
WA90-5
S51 Switch Work Lamps 48 H29 Control Lamp High Beem 41 E1 Head Light Left 38 E68.2 Turn Light Rear Left 32 XJ... Connector Main Monitor - WA80-5
S70 Switch Brake Lamps 45 - - - E2 Head Light Right 40 E69.2 Turn Light Rear Right 34 XL... Connector Floor Frame Harness - WA70-5
S101 Switch Hazard 36 H31 Control Lamp Turn Light 32 E3 Work Lamp Front Left 48 E68.3 Stop Lamp Left 45 XC... Connector Cabine Harness -
S331.1 Steering Column Switch Turn 33 H51 Control Lamp Work Lamps 48 E4 Work Lamp Front Right 49 E69.3 Stop Lamp Right 47 XM... Connector Engine Harness -
S331.2 Steer.Column Switch Head Lamps 38 H101 Control Lamp Hazard 36 E5 Turn Light Front Left 32 E71 License Lambs 42 XF... Connector Front Frame Harness -
S331.3 Steering Column Switch Horn 29 - - - E6 Turn Light Front Right 34 E123 Interior Lamp 54 XC... Connector Cabine Harness -
- - - - - - E60 Work Lamp Rear Left 51 - - - - - -
R246 Cigar Lighter 55 B8 Horn 29 E61 Work Lamp Rear Right 52 K56.1 Relay Low Beam 38 - - -
- - - - - - E68.1 Position Lamp Rear Left 43 K56.2 Relay High Beam 40 - - -
V118 Diode 44 P426 Main Monitor 32 E69.1 Position Lamp Rear Right 44 K67 Flasher 31 F... Connector Fuse -
WA90-5 / WA100M-5 90-11

Wiring diagram 3/5
30
15
20A
20A
20A
10A
10A
10A
10A
F1.7 F1.8 F1.5 F3.1 F3.1 F3.5 F3.7
1RB
1.5RY
1.5RY
0.5Gr
1BrW
1RB
1RG
1BY
1V
S379
9 10 9 10
1V
0.5WY
0.5WB
L
H396 1V 1V 0.5Gr 0.5Y H445
M
9 2 7 9 2 7 30 86 30 86
1BrW
H
0.5RY
0 0
I I H377
H56 I 0 H328 I 0
C I 7 P426 I
5 65¹ 65¹ 5
1
XJ15 11 XL27 7 5
1
B
S54 S397 S56 10 5 4 S328 10 5 4 87a 87 85 K209 87a 87 85 K376 S445

0.5B
0.5Br
1WR
0.5W
1BV
1.5RB
0.5BrY
0.5BrR
0.5Gr
0.5RY
1.5RBr
1Br
1G
1L
1L
1L
1L
1Br
XL41 1 2 XL40 2 1 XOP1 12 1
1RY
1Br
1B
1B
1L
1B
30 30
¹ ¹
Y214 Y213
XM3 3 4 XF7 B A C XF1 12
1W
1BrY
1BrR
1Gr
1L
1B
XL2 2 3 4 2 XL1 5 2 3 1 6 XM12 C A B XL50 2 3 1 4 XF8 B A C XF5 2 1
1.5WR
1.5RBr
1.5Br
1.5L
1BrY
1BrR
1G
1G
1Y
1B
1Y
1B
1R
1B
1R
1B
1L
1L
1Br
1B
1L
0.9 1.4 1.8
53 31b 53a - +
- - + 53 31b 53a 1 2 2 1
¹ ¹ ¹
NPN
M M M M M 5.3 5.3
30 3.5 5.0 5.0 45 3.5 ¹ ¹
rpm A ¹ ¹ rpm A
1.1¹
M78 R396 M7 53b 31 M182.1 M182.2 M248 31 S117 Y376 Y446
0.5B
0.5B
0.5B
1B
1B
2.5B
0.5B
0.5B
0.5B
1.5B
1B
1B
1B
1B
31
57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84
Position
WA100M-5
No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos. WA90-5
WA80-5
M7 Wiper Motor Front 64 S54 Switch Blower Heating System 57 H56 Control Lamp Wiper Front 63 XJ... Connector Main Monitor -
WA70-5
M78 Blower Heating System 58 S56 Switch Wiper/Washer Front 63 Y213 Magnet Coil RtD 73 H328 Control Lamp Wiper Rear 67 XL... Connector Floor Frame Harness - WA65-5
M182.1 Motor Pumpe Window Washer Front 66 S117 Switch RtD 74 Y214 Magnet Coil Dedent 71 H396 Control Lamp Rear Window Heater 61 XC... Connector Cabine Harness -
M182.2 Motor Pumpe Window Washer Rear 67 Y376 Magnet Differential Lock 77 H445 Control Lamp Quick Coupler 79 XM... Connector Engine Harness -
M248 Wiper Motor Rear 69 S328 Switch Wiper/Washer Rear 67 Y446 Magnet Valve Quick Coupler 82 - - - XF... Connector Front Frame Harness -
- - - S397 Switch Rear Window Heater 60 - - - - - - - - -
- - - S379 Switch Differential Lock 79 - - - K209 Relay RtD 75 - - -
- - - S445 Switch Quick Coupler 82 - - - K376 Relay Differential Lock 78 - - -
- - - - - - - - - - - - - - -
P426 Main Monitor 77 - - - - - - R396 Rear Window Heater 61 F... Fuse -
s1ig_7
WA90-5 / WA100M-5 90-13

Wiring diagram 4/5
15
25A
20A
10A
10A
10A
F2.1 F3.5 F3.1 F1.7 F3.2
1RY 1RY
1.5RY
2.5Gr
XL63 1 XL63 1
0.5BrR
0.5RB
0.5RY
S261 (27)XJ4:3 1BrB
9 10
1RY
0.5B
H318 (20km/h)
0.5WBr
0.5WB
800Hz 650Hz
On n Off L
H316 1GY
M
1R
550Hz 400Hz 86 30 86 30
0 H
H379 E35 (30km/h)
P426 I 7 P426 C
0.5W
XJ12 6 6 5 XL27 5 XJ4 1 K314 4 8 2 5 6 V118.4 65¹ 65¹
1 1YB
B
S316 S411 K411 85 87 87a S54 S296 K296 85 87 87a
0.5RG
0.5BrB 0.5BrB 0.5BrB
1WR
0.5WBr
0.5RW
2.5GrB
1GY
0.5RG
0.5W
1BrB
1BrB
1.5RBr
0.5R
1L
1RG
0.5B
V118.4
XL63 2 XL63 2
XL61 XL60
30 15
1RG 1RG
31
1RG
1RG
K235 87 87a
1RW
XF1 10 XM2 8 9 XF1 11 XF1 11
(20)Y235:1
1W
1RG
1RG
1B
1L
1G
XF6 2 1 XF2 2 1 XF2 2 1 XL2 1 3 4 2 XM3 10 XK3 1 2 XK3 4 3

1RG
1RG
1RG
1BrB
1B
1B
1B
1B
1B 1B
1.5W
1G
1G
2.5B
2.5Br
1L
1.5Br
1.5B
1.5R
1BrB 1BrB
2 1 2 1 2 1 2 1 2 1 2 1 XK5 1 2
0.8 1.1 2.2
¹ ¹ ¹ + -
OFF:27bar
9.6 9.6 9.6 12 12 12 M 4.2 M
¹ ¹ ¹ _ ¹ ¹ ¹
t˚ p 0.8¹
ON : 2bar
B228 M78 B293 Y293 B296 M296
Y315.3 Y315.2 Y315.1 Y411 Y411 Y412
Option OCV Option OCV
2.5B
2.5B
0.5B
0.5B
0.5B
0.5B
0.5B
1B
1B
1B
1.5B
WA65-5 WA80-5
WA70-5 WA90-5
WA100M-5
31
85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112
Position next see page 5

WA100M-5
WA90-5
No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos.
WA80-5
- - - S54 Switch Blower Air Condition 100 B228 Sensor Speed 93 - - - XJ... Connector Main Monitor - WA70-5
- - - S261 Switch Drive Range 87 - - - - - - XL... Connector Floor Frame Harness - WA65-5
Y293 Magnet Clutch Compressor 103 S296 Switch Air Condition 102 B293 Thermostat Air Condition 102 - - - XC... Connector Cabine Harness -
Y315... Magnet Valve ALS 89 S316 Switch ALS 89 B296 Pressure Switch Condensor 105 H316 Control Lamp Switch ALS 89 XM... Connector Engine Harness -
- - - S411 Switch OCV 94 - - - H318 Control Lamp Magnet Valve ALS 90 XF... Connector Front Frame Harness -
Y411 Magnet Valve OCV 95 K235 Relay Driving Range 86 - - - H379 Control Lamp Driving Range 86 XA... Connector Axle Harness -
Y412 Magnet Valve OCV 98 K296 Relay Air Condition 105 - - - - - - XK... Connector Air Condition Harness -
- - - K314 Switch Frequency ALS 92 - - - V118.4 Diode 94 - - -
M78 Motor Blower Air Condition 101 K411 Relay OCV 97 - - - - - - - - -
M296 Motor Blower Condensor 106 P426 Main Monitor 85 - - - - - - F... Fuse -
s39g_8
WA90-5 / WA100M-5 90-15

Wiring diagram 5/5
30
15
10A
10A
10A
10A
10A
10A
10A
F1.3 F3.3 F3.5 F3.4 F3.6 F3.8 F3.7
1RW
1RG
1RG
1.5RB
1RB
1LY
0.5G
(17)K373.2:87
S455
1GW
1R
S331.2:2
0.5YG
9 10 9 10
1GB
XL52 4 7 8
1R
H195 H443
1RG
1RG
86 30
0
XS4 XS4 0
1 2
I 7 XS5 XS5 I 7
65¹ 5 5
XOP2 1
10A
1 1
1GW
1GB
A249 K385 85 87 87a S195 F2.5 S443
XL62 5 6 3 4
1BrW
1BrR
1RY
1RG
1.5RB
1GL
1RY
1Br
1Br
S456 S457
1WB
1W
XS5 XS5
XM3 5 3 4 XZ1 1 XOP1 6 7 XOP1 10 8 XOP1 9
XS4 XS4
1GL
1GL
1RB
1RY
1R
1WB
1W
1RG
1.5R
H444 S444 S441
1.5B
87a 87 86 87a 87 86
1.5B
90¹ 90¹
1RB
1Br
1L
1 2 XM10 M
30 85 30 85
K458 K459
1.5B
(40)XM6:2(58L)
2 3 1
M441
M t
R444
1.5RW
1.5RB
1RG
1GL
1.5R
1B
M407
1B
1Br
1RG
30A
XB1 1 2 XB2 1 2 X130 + - XS3 2 1 2 1 XM11 XZ1 2 X48 31 58L X48 54
F6
1.5R
1GL
1GL
1RY
1B
1R
1.5B
1B
(4)F5:E
1Br
1Br
0.5B
0.5B
0.5R
0.5R
1B
1B
1B
1B
M M
0.6 ¹ XOP2 2
5.5A
W309 B245.1 B245.2 B279.1 B279.2 E130 M460 E71 E72 E243 E244 M443
1.5B
1B
1.5B
0.5B
0.5B
0.5B
1B
0.5B
1B
1B
1B
31
113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140
Position WA100M-5
WA90-5
WA80-5
Color Symbol
No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos. No. Componente Pos. WA70-5
white W
- - - K376 Relay Differential Lock 132 M407 Central Lublication 123 XJ... Connector Main Monitor - black B
- - - K458 Relay Up 136 M441 Compressor Seat 121 XL... Connector Floor Frame Harness - red R
- - - K459 Relay Down 138 M460 Linear Actuator 137 XC... Connector Cabine Harness - yellow Y
- - - S379 Switch Differential Lock 133 H377 Control Lamp Differential Lock 134 XM... Connector Engine Harness - green G
blue L
- - - S441 Switch Seat Air Suspension 121 H443 Control Lamp Sweeper 128 XF... Connector Front Frame Harness - brown Br
Y376 Valve Differential Lock 131 S443 Switch Sweeper Spray 128 H444 Control Lamp Seat Heater 120 XA... Connector Axle Harness - light green Lg
S444 Switch Seat Heater 120 A249 Car Radio 114 E71 Licence Lamp Left 117 XK... Connector Air Condition Harness - grey Gr
- - - S445 Pushbotton Switch Power 137 W309 Antenna 113 E72 Licence Lamp Right 118 XZ... Connector Seat - pink P
light blue Sb
S446 Pushbotton Switch Up 137 B245.1 Loudspeaker Left 114 E243 Position Light Sweeper Left 126 - - - orange O
R444 Seat Heater 120 S447 Pushbotton Switch Down 138 B245.2 Loudspeaker Right 115 E244 Position Light Sweeper Right 127 F.. Fuse - violet V
-
s39g_9
WA90-5 / WA100M-5 90-17

Wiring diagram, Speed control
WA90-5 / WA100M-5 90-19

Wiring diagram, Immobilizer
WA90-5 / WA100M-5 90-21

Wa90 5 Vebm270100

Uploaded by

Copyright:

Available Formats

Wa90 5 Vebm270100

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Wa90 5 Vebm270100

Uploaded by

Copyright:

Available Formats

Shop Manual VEBM270100

10 STRUCTURE AND FUNCTION . . . . . . . . . . . . . . . . . . . . . .10-1

20 TESTING AND ADJUSTING . . . . . . . . . . . . . . . . . . . . . . . .20-1

30 DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . .30-1

00-2 WA90-5 / WA100M-5

WA90-5 / WA100M-5 00-1

00-2 WA90-5 / WA100M-5

Important Safety Notice

2. When carrying out any operation, always wear safety shoes

• Always wear safety glasses when hitting parts with a

• Always wear safety glasses when grinding parts with a

3. If welding repairs are needed, always have a trained, experi-

4. When carrying out any operation with two or more workers,

WA90-5 / WA100M-5 00-3

6. Decide a place in the repair workshop to keep tools and re-

Preparations for work

2. Before starting work, lower blade, ripper, bucket or any other

3. When disassembling or assembling, support the machine

Tipping up the driver's cab

1. Park the machine on solid, level ground.

3. Close the cab door.

4. Use the locking bolt to secure the articulated steering (cross-

The machine has to be positioned straight and the articu-

5. Open the bonnet.

6. Remove 3 cover fastening screws on each side of the

7. Remove the cover.

00-4 WA90-5 / WA100M-5

8. Remove the cab fastening screws under the rear wheel

WA90-5 / WA100M-5 00-5

13. Take the lever out of the pump.

Tipping down the driver's cab

00-6 WA90-5 / WA100M-5

Torque = 230 Nm.

WA90-5 / WA100M-5 00-7

6. Reattach the cover.

7. Screw in 3 cover fastening screws on each side of the

8. Close the bonnet.

Tipping up the driver's cab (option with electric actuator)

1. Park the machine on solid, level ground.

3. Close the cab door.

4. Use the locking bolt to secure the articulated steering (cross-

The machine has to be positioned straight and the articu-

5. Open the bonnet.

6. Remove 3 cover fastening screws on each side of the

7. Remove the cover.

00-8 WA90-5 / WA100M-5

WA90-5 / WA100M-5 00-9

Tipping down the driver's cab (option with electric actuator)

3. Press the "On" (3) and "Lower" (5) buttons simultaneously,

00-10 WA90-5 / WA100M-5

Torque = 300 Nm.

5. Reattach the cover.

6. Screw in 3 cover fastening screws on each side of the

7. Close the bonnet.

Precautions during work

2. When removing the oil filler cap, drain plug or hydraulic

5. When raising heavy components, use a hoist or crane.

6. When removing covers which are under internal pressure or

7. When removing components, be careful not to break or