The

Of UV Measurement &
Process Control

Instrument Markets
Jim Raymont
Sterling, VA
The “Real” ABC Experts Were
Not Available
 The CBAV’s of UV Measurement &
ABC’s Process Control
Webinar Agenda
• Review ‘key’ UV measurement &
process control concepts
• All inclusive? No
• Good start? Yes-these are a few on my
favorite terms
• Reviewed by “letter” with some poetic
license

• Resources
• Copy of this presentation available
• RadTech UV Measurement Glossary
(www.radtech.org)
 ABC’s of UV Measurement &
Process Control
• Wide variety of commercial instruments available for different
sources and applications
• What are your needs?
• Define a process?
• Maintain process?
• R&D?
• Data Retention?
• Where will you measure?
• Production environment or lab environment
• Who will use it?
• Ease of use and features needed
• What is source type, size, expected dynamic range, spectral output?
• What values do you need?
• Absolute: Joules, Watts, Irradiance Profile, Spectral Profile
• Relative: Change over time, continuous monitoring

Let the fun begin………..

Absolute Readings
• Units: mJ/cm2 and mW/cm2
• Want a “number” Arc Lamps
– Match a specification
– Troubleshoot
– Optimize a process
– Compare multiple lines
– Communicate data
Additive Lamps
• Spectral output matched
to formulation
Application • AKA: Doped, Halide or
• Ability to measure? Special Fill
• Strategy? • Alphabet Soup
• Mercury (H)
• Mercury-Iron (D)
• Mercury-Gallium (V)
Accuracy
• The degree of closeness to that quantity's actual (true) value
• Precision: The ability of a measurement to be consistently reproduced.

• Users expect the same accuracy as other instruments

• Current UV radiometer technology +/- 7-10%
• Improve under controlled conditions to ± 2-3%
Bands (UV Spectrum)

Bands/Band Pass Filters

(Instrument Response)

• UVA: 320-390nm “Black light”, UV

Inks, adhesion
• UVB: 280-320nm “Toughness” , skin
response
• UVC: 200-280nm, germicidal (254 • Match instrument to needs for your
nm), surface cure, tack, chemical or application
scratch resistance • Narrow vs. broad band instruments
• UVV: 395-445nm, opaque/white, • Advantages of looking at both short
thick coats, adhesion, depth of cure (UVC) and long (UVA, UVV)
• UVA2 Band for 395 nm LEDs
Calibration & Service
• Instruments used in harsh
production & manufacturing
environments
• Compensate for changes
o Electronics & Optics checked
o Physical damage: Dropped,
over temperature, external
optics coated or damaged, unit
went for a swim in coating )
Communication
• Frequency of calibration?
• If you are not talking you may not
Cosine Response be not curing
o Formulator (Ink, Coating, Adhesive)
• Ability of instrument to measure UV o Application Equipment
at low incidence angles o UV Source Supplier
• Replicate how coatings behave o Substrate Supplier
o UV Measurement Supplier
• TBD-New sources (LEDs) behave
the same or differently?
 Caution! I’ve Got Numbers

But I get readings with my radiometer…..

Radiometer readings need to be qualified

and understood!

RTM
Read
The
Manual
 Data Organization
• Do not rely only on formulator
“radiometer”
Dynamic Range (Instrument) o Clipboard?
• Match Instrument to Source &
Application o Electronic?
o Procedures?
o 10’s of mW to 20,000+ mW/cm2
• Weigh a Baby on Truck Scale? But I Get
Readings?
o Barely trip instrument ‘on’ or using it in
the suggested operating range
o Low side of range-variation
o Very, very, very stable readings: Did I
max out unit?

Dose (See Energy Density) Where were those UV readings?

(Radiant) Energy Density
• Expressed in Joules (J/cm2) or Expectations (User)
milliJoules (mJ/cm2) per square
centimeter • Treat and handle as an
• Incorporates time as part of the instrument
measurement • Maintain, calibrate & service as
• One watt for One second = One Joule required
• Area under the irradiance curve
• Use as designed within specs
• Often the only UV exposure guide
number supplied Peak
• Avoid user induced errors
Irradiance
• PICNIC Errors: Problem In Chair,
Not In Calibration

Equipment Suppliers
Time • Use as a resource
Focus

Frequency: Power Supply

• Traditional 50/60 Hz power supplies
vs. higher frequency power supplies
• Impact on chemistry?
NON-
NON-FOCUSED FOCUSED
290 mW/cm2 858 mW/cm2
1707 mJ/cm2 2096 mJ/cm2

0.025 seconds

High frequency power supply

Formulation/Formulator
• Match Formulation to Application
• Use Formulator as a Resource and not just a complaint department
Goals
Goals are deceptive-the unaimed arrow never misses
Charles Knief (Kimo’s Rules)
Guess
Anything that you can measure, you have a better chance of controlling.
Things that you do not measure become the cause of mysterious
problems Larry Goldberg-Beta Industries
Health & Safety
• www.radtech.org
How Often Do I Measure?
• Chemical Safety
• Application?
• PPE
• Value of Product?
• Housekeeping
• Type of Product?
• Reporting Requirements
• Process Window?
• Hygiene
• Equipment Safety
Handshake
• The UV source and formulation need to do a “handshake”
• Modify formulation designed for broadband UV sources to work
on a narrow band UV source such as UV LED
• Verify you get the desired properties and performance under a
new source
Irradiance (Intensity)
• Expressed in watts or milliWatts per square centimeter (W/cm2 or mW/cm2)
• Total radiant power of (all) wavelengths passing from all incident directions
onto an infinitesimally small area (cm2)
• Readings decrease with the square of the distance (True for LEDs?)
• Depth of cure, penetration through pigments and opaque colors, adhesion to
the substrate

dA
Infrared
• What role does it play in your
application?
o Cure?
o Substrate?
o Cooling of UV Source?
Coating Specification: 4 Joules/cm2
1 Joule = 1 Watt for 1 Second

4 Joule Exposures
• 4 Watts-1 Second
4 Watts
• 1 Watt-4 Seconds
1 Second • 2 Watts- 2 Seconds

2 Watts
1 Watt-4 Seconds
2 Seconds

Equal Joules = Equal Cure?

Knowledge
• Web Sites
– SGIA
– RadTech Web site
– Supplier/Vendor websites
• Articles
• Seminars/Webinars
• Conference & Trade Shows
• Trade Organizations (SGIA, RadTech,
Industry)
• Suppliers/Vendors
• Training Materials (CD/DVD)
Lamps

• Differences in materials, fill elements,

pressure
• Useful life of lamp
• Buy on value, not the least expensive
price
• “Purchasing Specials”

Line Speed
Log Dwell Time UV System: North Line Lamp: 2 Other Signature
Date FPM/RPM
Ind. Actual. Power Hour Irradiance Energy
WPI Meter (W/cm2) Density
(J/cm2)

10/4 25 22 400 780 0.859 1.45

(UV) LEDs

• Manufacturers use proprietary processes to select, bin (test) and assemble

LED chips into arrays with optics
• Bin by spectral output, intensity and forward voltage
(UV) LEDs
• Instrument Bandwidth Matched to Source
• Spectral Distribution from a 365 nm LED UV Source

Source Irradiance & UVA Responsivity

Spectral
1
Irradiance is
Relative Radiant Power/Responsivity

0.9 grouped in 10-

nm bands.
0.8

0.7
LED
0.6 365nm

0.5
UVA
0.4

0.3
0.2

0.1
0
200 250 300 350 400 450 500 550 600
Wavelength (nm) Radiant Power data is for 100mW Nichia LED.
UVA Responsivity obtained from EIT LLC.
 Caution! I’ve Got Numbers
(UV) LEDs
• Instrument Bandwidth Not Matched to Source
• Measurement of 395 nm LED with EIT UVA (320-390 nm) and EIT UVV (390-445nm)

Source Irradiance & UVA and V Responsivity

1 Spectral
Irradiance is
Relative Radiant Power/Responsivity

0.9 grouped in 10-

nm bands.
0.8

0.7 LED
395nm
0.6
UVA
0.5

0.4 UVV

0.3

0.2

0.1

0
200 250 300 350 400 450 500 550 600
Wavelength (nm) Radiant Power data is for 395nm Nichia LED.
UVA and V Responsivity obtained from EIT LLC.
(UV) LEDs
• 395 nm LED with EIT UVA2 (380-410 nm)
• Instrument Bandwidth Matched to Source

UVA2 available in:

• Power Puck II & Power Puck II
Profiler (UVA, UVA2, UVB, UVV)
• UviCure Plus II & UviCure Plus II
Profiler (UVA2)
• Special order PowerMAP & UV Map
Plus

300 350 400 450

Wavelength (nm) Radiant Power
UVA2 Respon
(UV) LEDs
Location of the UV LED Measurement
• Where is the proper location for the UV Irradiance Value?
• How do we compare systems and communicate values?

Courtesy of Integration Technology

Measurement (Why)
• Save Time & Money
Maintenance
• Preventative, Simple & Major
Maintenance
• Procedures & Training

Microwave
Nanometer
• A nanometer is equal to one billionth
(1/1,000,000,000 or 10-9) of a meter
o Water molecule is less than 1 nm
o Typical germ is about 1,000 nm
o Hair is about 100,000 nm wide
o Shaquille O’Neal is 2,160,000,000 nm tall
• Non-vacuum UV: +/- 200 nm to 400-450
nm (visible light)
• Nanometers also used to describe
instrument bands
– EIT UVA response is 320-390 nm

NIST Traceability
• Process to transfer “NIST” traceable reading into customer instrument
Online UV Measurement
• Continuous feedback & monitoring
– Tight process windows/High $
Products
– UV changes with time
– Feedback to display, PLC, Alarms
• Applications where a radiometer will
not fit or is not practical
– Web, Bank of multiple lamps
– Lamps high off ground
• Communication
– Percentage readings
– Coordinate with absolute radiometer EMI Hardened Sensor for
Online measurements
 Optics
• Filter and detector specifications
• Spatial response (Cosine)
• Design-Balance between optical stability &
repeatable electronic signal level
• Proper care and cleaning

Cleaning The Optics

1. LOOK
2. BLOW
3. FLOOD
4. WIPE New Filter Customer Returns:
Left: Improper Cleaning Right: Scratch
Process Windows
• Require work to establish,
document & maintain the process
• Require communication with
suppliers, vendors, etc.
• Follow the Laws of Physics

Are we to believe that a UV (LED) photon soaks into a coating

faster in your lab than anywhere else on the face of the earth?
Well, I guess the laws of physics cease to exist in your lab. Are
you using magic UV (LED) photons? Magic coatings?
Did you buy them from the same guy who sold Jack his
beanstalk beans?
Paraphrased from My Cousin Vinnie
Process Window
• The range in which a process will work with the desired results
• Adhesion, hardness, flexibility, gloss, texture, stain or scratch resistance,
chemical rub, cross hatch, abrasion rub, color ID, registration

Penetration (Adhesion)
UVC UVB UVA UVV
Normal Operating Window

Caution Undercure Buffer Range

Stop! Undercure Limit
Ink, coating, adhesive thickness
Substrate Surface
Profiling Radiometers
• Measure the peak irradiance and
total energy density
• Profile the UV irradiance (y-axis) as
a function of time (x-axis)
Some also profile temperature
• Irradiance profiles useful to:
Analyze system changes over
time
Compare multi-lamp systems
Trouble shoot lines
View lamp focus
Determine lamp type
Power supply analysis
• Software or Display
Profiling Radiometers
Qualify, Quantify & Quality
• UV Measurement & Process Control allows you
to Qualify & Quantify a UV process
• UV Measurement & Process Control Allows you
to Produce Good Quality Products
Relative Measurement
• Electronic signal proportional to
lamp brightness (% intensity)
• Sensor & Display
Real Time Monitoring
• Situational awareness, into PLC display

Reflectors
• 60-80% of energy reaching
the substrate is reflected
• Optimize reflected energy,
reflector focus and lamp
position through design and
maintenance programs
• Shape, type, material, coating
of reflector matched to
process
Radiochromatic Strips
• Web press option
• Clean Reflectors are key to
success • Correlate to radiometer or color?
Specification (Cure)
• Applied electrical power is not enough (i.e. 200 WPI lamp)
• Minimum energy density: 700 mJ/cm2, EIT UVA (320-390)
• Minimum irradiance: 650 mW/cm2, EIT UVA (320-390)
• Lamp Type, Reflector Type, Thermal, Coating Thickness

Spectral Radiometer
• Irradiance as function of wavelength
• Available from UV bulb/equipment supplier
• R&D value vs. production value?
Sampling Rate
• Did your instrument take enough samples
to avoid errors and ‘catch’ the peak? 910 mW/cm2 (RMS)

• Sample rates have increased in more

recent instruments

Smoothing (Data Filtering)

• Instruments have the ability to sample
faster
• Peak irradiance: Report average (RMS)
or instantaneous peak?
1866 mW/cm2
• 910 mW/cm2 (RMS/Smooth On) or 1866
mW/Cm2 (Instant/Smooth Off)?
Threshold (Start)
• Irradiance level which causes the unit to start measuring UV
• Varies due to dynamic range, electronic response, optics,
design
• Use the right dynamic range instrument

Temperature
• Avoid sending an instrument through rapid, repeated,
long duration, high UV intensity/temperature runs
• Alarms on units
• If the instrument is too hot to touch – it’s too hot to
measure

Three Dimensional (3D)

• Many UV applications are
3-dimensional & require
measurement for uniformity
Units
• Instrument Bandwidths are not defined and vary from manufacturer to
manufacturer and how they are specified
o EIT UVA 320-390 nm, Full Width Half Max (FWHM), CWL 365 nm
o IL UVA 250-415 nm CWL 365 nm

IL UVA
250-415
EIT nm
UVA 320-
390 nm

• Specify units in measurement to avoid confusion

o 300 mJ/cm2 Start
o 300 mJ/cm2-UVA Improvement
o 300 mJ/cm2-UVA EIT 320-390 nm Best
Variables (Process) Verification & Validation
• UV Output (W/cm2, J/cm2 or • Establish your process window
Relative Intensity) during the design/development
• Bulb Life/Bulb Type phase and start monitoring from
• Reflectors day one in production

• Incoming Electrical Power (Volts, • Monitor your readings by job,

Amps) hour, shift or day as required to
• Applied Power (WPI) maintain quality to avoid:

• Process Speed (J/cm2)

• Substrate
• Formulation
• Application Equipment
• Machine Equipment
Wavelength
• For UV, the wavelength is most
often measured in nanometers (nm)
Watts (For UV Curing)
Irradiance Watts
• Units: Watts or milliWatts per square centimeter (W/cm2 or mW/cm2)
• Total radiant power of (all) wavelengths passing from all incident directions onto
an infinitesimally small area (cm2)
Total Applied Power to UV Source Watts
• Amount of electrical power applied to a UV source
• Total Watts: Voltage x Amperage
Lamp Power Settings
• Voltage x Amperage/Arc length of bulb
• If bulb length is measured in inches: WPI
• If bulb length is measured in centimeters: WPCM

Total power applied to the system or the lamp power setting is not the
effective amount of UV generated or effective amount of UV
reaching the cure surface
Xenon Sources
• Pulsed UV energy
• Not all instruments can measure short duration
high energy pulses-need modified electronics for
pulsed sources
• Coordinate with source and instrument supplier
Yield
• At the end of the day, UV Measurement &
Process Control is all about being able to
produce good quality products at a profit
Thank You EIT-Instrument Markets
Jim Raymont
• Zee Presentation available as PDF 108 Carpenter Drive
• Zee Questions? Sterling, VA 20164
Phone: 703-478-0700
Fax: 703-478-0291
jraymont@eit.com
uv@eit.com
And now that you know www.eit.com
your UV ABC’s, won’t
you sing along with
me…!