Industrial Sensors

Industrial Sensors
• Proximity
– Mechanical
– Optical
– Inductive/Capacitive
• Position/Velocity
– Potentiometer
– LVDT
– Encoders
– Tachogenerator
• Force/Pressure
• Vibration/acceleration

1
 Definitions Proximity Sensors
• Accuracy: The agreement between the actual • Widely used in general industrial automation
value and the measured value – Conveyor lines (counting,jam detection, etc)
• Resolution: The change in measured variable – Machine tools (safety interlock, sequencing)
to which the sensor will respond • Usually digital (on/off) sensors detecting the
• Repeatability: Variation of sensor presence or absence of an object
measurements when the same quantity is • Consist of:
measured several times – Sensor head: optical, inductive, capacitive
• Range: Upper and lower limits of the variable – Detector circuit
that can be measured – Amplifier
• Sensitivity and Linearity – Output circuit: TTL, solid state relay

Example Mechanical
Mechanical Proximity Switches
Proximity Switches
• Essentially a
mechanical switch
• On/off operation only
• Two general modes
– Normally Open (NO)
– Normally Closed (NC)
• Come in a wide variety Actuator Normally
of mechanical forms Closed

• For a wide range of Common

uses Normally
Open

2
 When to Use Mechanical Applications and Use of
Proximity Switches Mechanical Proximity Switches
• Easy to integrate into machinery of all
• Where physical contact is possible types
• Where definitive position is required • Requires contact (thus wear)
• Range of voltages: DC 0-1000V, AC, etc.
• In operation-critical or safety-critical
• Very robust (explosion proof if required)
situations
• Usually used as:
• Where environment conditions preclude – Limit switch
the use of optical or inductive sensors – Presence/absence indicator
– Door closed/open

Places You Find Mechanical

Optical Proximity Sensors
Proximity Switches !
• Consist of a light source (LED) and light detector
(phototransistor)
• Modulation of signal to minimize ambient lighting
conditions
• Various models: 12-30V DC, 24-240V AC, power
• Output: TTL 5V, Solid-state relay, etc.

Modulator Power Power Supply

Mixer Signal Load

Demodulator
Output
Amplifier

3
 Operational Modes Example Optical Proximity I
• Through Beam:
– Long range (20m)
Optical Fibre
– Alignment is critical ! Delivery System

• Retro-reflective
– Range 1-3m
– Popular and cheap

• Diffuse-reflective
– Range 12-300mm
– Cheap and easy to use

When to use an Optical

Example Optical Proximity II
Proximity Sensor
Slot Beam
• Pros
Systems – Non-contact, no moving parts, small.
– Fast switching, no switch bounce.
– Insensitive to vibration and shock
– Many configurations available
• Cons
– Alignment always required
– Can be blinded by ambient light conditions
(welding for example)
– Requires clean, dust and water free, environment

4
Applications of Optical Proximity
Other Optical Devices
Sensors
Collision Detection
• Stack height control/box counting
• Fluid level control (filling and clarity) Light
• Breakage and jam detection Curtain

• And many others…

http://www.omron-ap.com/application_ex/index.htm
http://www.sick.de/english/products/products.htm
http://content.honeywell.com/sensing/prodinfo/

Ultrasonic Proximity Sensors When to use Ultrasonic Sensors

• Use sound pulses
• Measures amplitude and
time of flight • Provide range data directly:
• Range provides more than • Level monitoring of solid and liquids
on/off information • Approach warning (collisions)
• Frequencies 40KHz-2MHz • Can (usually) work in heavy dust and
Vibrating Membrane water
(metal or ceramic)
• Ambient noise is potentially an issue
Pulse
Sensor Object http://www.automationsensors.com/
Echo

5
 Inductive and Capacitive
Example Applications
Proximity Sensors
Car Wash Paper roll Waste water
Application Thickness Monitor flow volume • Inductive sensors use change in local
magnetic field to detect presence of metal
target
• Capacitive Sensors use change in local
capacitance caused by non-metallic
objects
• Generally short ranges only
• Regarded as very robust and reliable

Example Inductive Sensors I Example Inductive Sensors II

Bulk mounted inductive

sensors. Detect presence of
object without contact.
Range 3mm +/- 10%

Detection of
open/close functions
Detection of
rotation

6
Example Capacitive Sensors Position and Velocity Sensors
• Position and velocity measurement is often
Panel Mounted Capacitive required in feedback loops
Sensor. Can detect wood, • For positioning, and velocity control
plastic and metal.
Range 3mm-25mm • Position measurement:
– Potentiometers
– LVDT
Flat mounted Capacitive – Encoders
Sensor. Used for detecting
• Velocity Measurement:
panels of glass.
Range=10mm +/- 10% • Tachometer

Potentiometers Types of Potentiometer

An analog sensor • Wirewound
Works as a voltage divider – Wiper slides along coil of Ni-chrome wire
– Wire tends to fail, temperature variations
• Cermet
Vin R – Wiper slides on conductive ceramic track
Vout – Better than wire inmost respects
• Plastic film
– High resolution
– Long life and good temperature stability

7
 Linear Potentiometers When to use a Potentiometer

• Pros
– Require analog signal for control
– Require absolute positional information
– Low cost
• Cons
– Temperature and wear variations
– Not in dusty or wet environments

Linear Variable Differential

LVDT Signal Conditioning
Transformer (LVDT)
• An LVDT consists of a Vinsinωt • Uses AC modulation,
magnetic core that moves in a
cylinder demodulation and
• The sleeve of the cylinder Voutsin(ωt+φ)
contains a primary coil that is
phase comparison
driven by an oscillating • Available in a single
Phase measurement
voltage
• The sleeve also contains two monolithic package Zero
LVDT Set
secondary coils that detect
this oscillating voltage with a
magnitude equal to
Power Carrier Amplitude Current
displacement Demodulator
Supply Oscillator Control Amplifier
• The automatic nulling that can
be achieved using two coils
Phase
makes LVDTs very accurate
(submillimetre) AC Power Shifter

8
 Example LVDTs When to use an LVDT

Free core LVDTs for • High accuracy

use in hostile environments
And total emersion
• Linear operation (synchro resolver
is equivalent rotary LVDT)
• Harsh environment
Spring-loaded
Standard for use • Analog position control
In hydraulic cylinders • Embedding (in cylinder for
example)

Optical Encoders Encoder Internal Structure

• Encoders are digital Sensors commonly used to
provide position feedback for actuators
• Consist of a glass or plastic disc that rotates
between a light source (LED) and a pair of
photo-detectors
• Disk is encoded with alternate light and dark
sectors so pulses are produced as disk rotates

9
 Incremental Encoders Absolute Encoders
• Pulses from leds are • Absolute encoders
counted to provide have a unique code
rotary position that can be detected for
• Two detectors are every angular position
used to determine • Often in the form of a
direction (quadrature) “grey code”; a binary
• Index pulse used to code of minimal change
denote start point • Absolute encoders are
• Otherwise pulses are much more complex
not unique and expensive than
incremental encoders

Encoder processing When to Use an Encoder

• Need a squaring • Require accurate position
circuit to digitise information:
signal – 10,000 line incremental
• A counter and index – 360 line absolute
monitor • Digital feed-back loop
• Generally available in • Compact and reasonably
monolithic form rugged (not as good as
• Often with algorithms inductive)
for control externally • Linear encoders also
programmable available

10
 Tachometers Force and Pressure
• Measurement of rotary • Force and Pressure generally measured
speed using a DC
generator
indirectly through deflection of an alternate
• Essentially a motor
surface
running in reverse • Mechanism include:
• Used to be common to – Physical motion and measurement using (eg) an
have these attached to LVDT
motors to enable direct
analog feedback – Strain gauges (metal that changes resistance
when stressed)
• Much less common now Tacho generator for large
with digital control (use industrial plant (GE) – Piezo electric materials that generate a current
incremental encoders) when deformed

LVDT Load Cell Strain Gauge Bridge

Table Force ∆R ∆R
Spring or GF = R= R
Piston ∆L ε
L
Tension ∆R = R ⋅ GF ⋅ ε
LVDT
Vmeas ⎛ R3 R2 ⎞
Strain Gauges =⎜ − ⎟
Vexc ⎝ R3 + R4 R1 + R2 ⎠
Outer
Platform
assume R1 = R2 , R4 = RG ,
R3 = RG + ∆R
−4Vmeas
then ε =
GF ( 2Vmeas − Vexc )

11
 Example Load Cells Sub-miniature Load cells

Subminature Reaction torque Axial load cell

Load cells load cell All signal conditioning
and amplification integrated
http://www.entran.com/ltoc.htm Load cell bridge structure
with the sensor
5

Piezo Load Cells Pressure

• Distortion of crystal, • Pressure measured by:
either quartz or BaTiO3 – Pitot tube and
– Deformation of fixed
• Used for accurate membrane
measurement of small
• Deformation measured Miniature
loads
using same methods as
• Come in the form of: for force: Industry IP69
• single axis load • Spring (manometer)
washers
• Piezo distortion
• or multiple axis load
• Strain gauges
washers and tables High Temperature
Stefan Williams Mech 1701: Introduction to Mechatronics Slide 47

12
 Acceleration Tri-axial Accelerometers
• Acceleration is also • Triaxial accelerometers
measured via the force Single Axis, Triple axis
10,000g
used in mobile systems
exerted by an – In high-performance cars
Accelerometer
accelerating mass For racing cars
– Inside rotating elements
• Distortion of a piezo Shielded for of turbines
• Motion of a cantilever Severe – In aircraft elements
environment • Provide vibration
• Strain on mass
restraints information
• Accelerometers mainly EMI • Provide short-term
shielded position data
used to measure
vibration

Silicon Machined Accelerometers Silicon Gyroscopes

• Structural arrangement
Used in eg air-bags
of silicon which records
centrifugal acceleration
and thus angular speed
• Use strain-gauge
bridges and/or piezo
structure to record
deformations
• Multiple component
Cantilever elements to calibrate
beams other accelerations

13
 Inertial Systems
• Many different types of accelerometer and
gyroscope systems
• Mechanical bodies, fibre optic, etc
Ballistic
• Together in an orthogonal arrangement of Missile
accelerometers and gyroscopes, these
comprise an inertial measurement unit (IMU)
• An IMU that is used for navigation is called Aircraft
an inertial navigation system (INS)
• These are widely used in aircraft and missile
navigation and guidance

Summary
• There are many types of sensors available
today
• Selecting the right sensor is a critical part
of the design cycle
• Requires an understanding of
– Type of motion
– Precision of motion
– Magnitude of motion
– Operating conditions

14