Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 56 views

    Related Link::: I-7188EX-MTCP Redundancy System: M M-7000 I/O

    Uploaded by

    Abraham Kennan Pasaribu
    Two Wincon controllers can be set up in a redundancy configuration. A PC or HMI can connect to a single I-7188EX-MTCP device, which converts Modbus TCP/IP to Modbus RTU and connects to the two controllers over RS-485. This allows the HMI to use a single IP address to communicate with the redundant controller system. Diagrams show the network configuration and how the I-7188EX-MTCP is configured as a gateway between TCP/IP and RTU protocols.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Related Link::: I-7188EX-MTCP Redundancy System: M M-7000 I/O

    Uploaded by

    Abraham Kennan Pasaribu
    56 views4 pages
    Two Wincon controllers can be set up in a redundancy configuration. A PC or HMI can connect to a single I-7188EX-MTCP device, which converts Modbus TCP/IP to Modbus RTU and connects to the two controllers over RS-485. This allows the HMI to use a single IP address to communicate with the redundant controller system. Diagrams show the network configuration and how the I-7188EX-MTCP is configured as a gateway between TCP/IP and RTU protocols.

    Original Title

    faq041.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Two Wincon controllers can be set up in a redundancy configuration. A PC or HMI can connect to a single I-7188EX-MTCP device, which converts Modbus TCP/IP to Modbus RTU and connects to the two controllers over RS-485. This allows the HMI to use a single IP address to communicate with the redundant controller system. Diagrams show the network configuration and how the I-7188EX-MTCP is configured as a gateway between TCP/IP and RTU protocols.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    56 views4 pages

    Related Link::: I-7188EX-MTCP Redundancy System: M M-7000 I/O

    Uploaded by

    Abraham Kennan Pasaribu
    Two Wincon controllers can be set up in a redundancy configuration. A PC or HMI can connect to a single I-7188EX-MTCP device, which converts Modbus TCP/IP to Modbus RTU and connects to the two controllers over RS-485. This allows the HMI to use a single IP address to communicate with the redundant controller system. Diagrams show the network configuration and how the I-7188EX-MTCP is configured as a gateway between TCP/IP and RTU protocols.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    FAQ-041: How to connect PC / HMI to a Redundancy system with a single IP address ?

    Two Wincon-8347/8747 & Wincon-8346/8746 can setup as one redundancy system. The
    PC / HMI / SCADA software can connect to one I-7188EX-MTCP to convert Modbus
    TCP/IP protocol to become Modbus RTU RS-485 protocol and then to these two
    redundancy controllers as below figures. Then the HMI software running on PC can use
    only one target IP address (7188EX-MTCP's IP) to link to the redundancy system.

    Related link:

    I-7188EX-MTCP : http://www.icpdas.com/products/PAC/i-7188_7186/Modbus_PAC.htm
    Redundancy system : http://www.icpdas.com/faq/isagraf/036.htm
    NS-205 / NS-208 : http://www.icpdas.com/products/Switch/industrial/ethernet_switch.htm
    M-7000 I/O : http://www.icpdas.com/products/Remote_IO/m-7000/m-7000_list.htm

    Figure 1:
    Figure 2:

    The redundancy system supports not only I-87K I/O in I-87K4/5/8/9 base, but also M-7000
    series I/O modules. http://www.icpdas.com/products/Remote_IO/m-7000/m-7000_list.htm

    Two redundancy Wincon-8x47 / Wincon-8x46 can connect their LAN1 to LAN1 and also
    LAN2 to LAN2. If one cable is damaged, the other one still works.
    If you have installed i-7188EX-MTCP in this example, please set a fixed IP to it by the
    “7188xw.exe” utility. (Power off 7188EX-MTCP, short its “INIT*” pin to “GND” , power it up,
    connecting one RS232 cable from i-7188EX-MTCP ‘s COM1 to PC ‘s COM1, PC running
    “7188xw.exe”, key-in, for ex, “ip=10.0.0.107” to set ip address and “mask=255.255.255.0” to set
    mask address)

    After i-7188EX-MTCP ’s IP and Mask is well set. Please run “Modbus utility” to configure this i-
    7188EX-MTCP to become a Modbus TCP/IP to Modbus RTU Gateway as below steps.

    Please set its COM1 as “Debug” mode.


    Then please set COM2 to “Modbus/RTU Gateway” , a proper timeout (250 ms), other parameters
    as 19200,8,None,1 . then Click on “Set”

    In the “System Setting” area, please set this i-7188EX-MTCP ‘s Net-ID to a value not equal to 1,
    for example, 100. And “Stations per COM Port as 1” , then click on “Set”.
    If it display “Modbus ID (1 ~ 1) ==> COM2” , the configuration is well done.

    Note: If i-7188EX-MTCP ‘s COM1 is not set as “Debug” mode in the former page, the setting will
    become “Modbus ID (1 ~ 1) ==> COM1” . That is not correct, because here we want it send to
    i-7188EX-MTCP ‘ s COM2:RS-485.

    Then when this i-7188EX-MTCP receives Modbus TCP/IP protocol to request Net-ID: 1, it will
    send this request to its COM2:RS-485 . And then if controller reply, it will reply back to the
    Ethernet port.

    You might also like