Group 2 Specifications: 1. Major Component
Group 2 Specifications: 1. Major Component
Group 2 Specifications: 1. Major Component
1. MAJOR COMPONENT
Engine
Radiator
Oil cooler
Bucket cylinder Side cutter Idler Carrier roller Track Travel motor
21072SP01A
1-10
2. SPECIFICATIONS
1) ROBEX 210LC-7H
I(I') D
E
C
G
F
H
J M
K N
A B(L)
21072SP02
1-11
2) ROBEX 210LC-7H LONG REACH
21072SP06
1-12
3. WORKING RANGE
1) R210LC-7H [5.68m(18' 8") BOOM]
8ft
21072SP03
1-13
2) R210LC-7H LONG REACH [8.2m(26' 11") BOOM]
A
A'
F
D
E
C
B'
B
8ft
29072SP08
1-14
4. WEIGHT
1) R210LC-7H
R210LC-7H
Item
kg lb
Upperstructure assembly 8950 19730
Main frame weld assembly 2600 5730
Engine assembly 530 1170
Main pump assembly 120 265
Main control valve assembly 200 440
Swing motor assembly 250 550
Hydraulic oil tank assembly 240 530
Fuel tank assembly 200 440
Counterweight 3800 8380
Cab assembly 310 680
Lower chassis assembly 8700 19180
Track frame weld assembly 2600 5730
Swing bearing 260 570
Travel motor assembly 310 680
Turning joint 55 120
Track recoil spring and idler 270 600
Idler 170 370
Carrier roller 20 45
Track roller 40 85
Track-chain assembly(600mm standard triple grouser shoe) 1320 2910
Front attachment assembly(5.68m boom, 2.92m arm,
4000 8820
0.92m3 SAE heaped bucket)
5.68m boom assembly 1535 3380
2.92m arm assembly 710 1570
0.92m SAE heaped bucket
3
765 1690
Boom cylinder assembly 180 400
Arm cylinder assembly 290 640
Bucket cylinder assembly 175 390
Bucket control link assembly 170 370
1-15
2) R210LC-7H LONG REACH
1-16
5. LIFTING CAPACITIES
1) ROBEX 210LC-7H
(1) 5.68m(18' 8") boom, 2.92m(9' 7") arm equipped with 0.92m3(SAE heaped) bucket, 600mm (24")
triple grouser shoe and 3800kg counterweight.
Note 1. Lifting capacity are based on SAE J1097 and ISO 10567.
2. Lifting capacity of the ROBEX series does not exceed 75% of tipping load with the machine
on firm, level ground or 87% of full hydraulic capacity.
3. The load point is a hook located on the back of the bucket.
4. *indicates load limited by hydraulic capacity.
1-17
2) R210LC-7H LONG REACH
(1) 8.2m(26' 11") boom, 6.3m(20' 8") arm equipped with 0.51m3(SAE heaped) bucket, 800mm (32")
triple grouser shoe and 5300kg counterweight.
1-18
6. BUCKET SELECTION GUIDE
1) GENERAL BUCKET
1) GENERAL BUCKET
Recommendation
Capacity Width
5.68m (18' 8") boom 8.2m (26' 11") boom
Weight
SAE CECE Without With 2.92m arm 6.30m arm
heaped heaped side cutter side cutter (9' 7") (20' 8")
ö : Standard bucket
Applicable for materials with density of 2000kgf/m3 (3370lbf/yd3) or less
Applicable for materials with density of 1600kgf/m3 (2700lbf/yd3) or less
Applicable for materials with density of 1100kgf/m3 (1850lbf/yd3) or less
1-19
2) HEAVY DUTY, ROCK AND SLOPE FINISHING BUCKET
Recommendation
Capacity Width
5.68m (18' 8") boom
Weight
SAE CECE Without With 2.92m arm
heaped heaped side cutter side cutter (9' 7")
1-20
7. UNDERCARRIAGE
1) TRACKS
X-leg type center frame is integrally welded with reinforced box-section track frames. The design
includes dry tracks, lubricated rollers, idlers, sprockets, hydraulic track adjusters with shock
absorbing springs and assembled track-type tractor shoes with triple grousers.
2) TYPES OF SHOES
Triple grouser
Model Shapes
Item Quantity
1-21
4) SELECTION OF TRACK SHOE
Suitable track shoes should be selected according to operating conditions.
Method of selecting shoes
Confirm the category from the list of applications in table 2, then use table 1 to select the shoe.
Wide shoes(Categories B and C) have limitations on applications. Before using wide shoes, check
the precautions, then investigate and study the operating conditions to confirm if these shoes are
suitable.
Select the narrowest shoe possible to meet the required flotation and ground pressure. Application
of wider shoes than recommendations will cause unexpected problem such as bending of shoes,
crack of link, breakage of pin, loosening of shoe bolts and the other various problems.
ö Table 1
ö Table 2
Category Applications Precautions
Rocky ground, Â Travel at low speed on rough ground with large obstacles such as
A river beds, boulders or fallen trees
normal soil
Normal soil, Â These shoes cannot be used on rough ground with large obstacles such
soft ground as boulders or fallen trees
B Â Travel at high speed only on flat ground
 Travel slowly at low speed if it is impossible to avoid going over obstacles
Extremely soft gound  Use the shoes only in the conditions that the machine sinks and it is
(Swampy ground) impossible to use the shoes of category A or B
 These shoes cannot be used on rough ground with large obstacles such
C as boulders or fallen trees
 Travel at high speed only on flat ground
 Travel slowly at low speed if it is impossible to avoid going over obstacles
1-22
8. SPECIFICATIONS FOR MAJOR COMPONENTS
1) ENGINE
Item Specification
2) MAIN PUMP
Item Specification
1-23
3) GEAR PUMP
Item Specification
Item Specification
5) SWING MOTOR
Item Specification
6) TRAVEL MOTOR
Item Specification
1-24
7) REMOTE CONTROL VALVE
Item Specification
8) CYLINDER
Item Specification
9) SHOE
1-25
10) BUCKET
Capacity Tooth Width
Item quantity Without side cutter With side cutter
SAE heaped CECE heaped
STD 0.92m (1.20yd )
3 3
0.80m3(1.05yd3) 5 1150mm(45.3") 1270mm(50.0")
0.52m3(0.67yd3) 0.45m3(0.59yd3) 5 935mm(36.8") 1035mm(40.7")
1.05m (1.37yd )
3 3
0.90m (1.18yd )
3 3
5 1250mm(49.2") 1370mm(53.9")
1.05m3(1.37yd3) 0.87m3(1.14yd3) 5 1115mm(43.9") 1235mm(48.6")
R210LC-7 OPT
1.20m (1.57yd )
3 3
1.00m (1.31yd )
3 3
5 1400mm(55.1") 1520mm(59.8")
ľ1.05m3(1.37yd3) 0.92m3(1.20yd3) 5 1290mm(50.8")
Ľ0.87m (1.14yd )
3 3
0.75m (0.98yd )
3 3
5 1035mm(920")
Ľ1.05m3(1.37yd3) 0.94m3(1.23yd3) 5 1445mm(56.9")
ľ : Heavy duty bucket
Ľ : Rock bucket(Heavy)
1-26
9. RECOMMENDED OILS
Ambient temperature Á
C (Á
F)
Capacity
Service point Kind of fluid -20 -10 0 10 20 30 40
˶(U.S. gal)
(-4) (14) (32) (50) (68) (86) (104)
SAE 30
SAE 10W
Engine
Engine oil 16.3(4.3)
oil pan SAE 10W-30
SAE 15W-40
NLGI NO.1
Swing drive Grease 1.2(0.3)
NLGI NO.2
Tank; ISO VG 32
180(48)
Hydraulic tank Hydraulic oil ISO VG 46
System;
290(77) ISO VG 68
NLGI NO.1
Fitting
(Grease nipple) Grease As required
NLGI NO.2
Mixture of
Radiator antifreeze
35(9.2) Ethylene glycol base permanent type
(Reservoir tank) and water
50 : 50
SAE : Society of Automotive Engineers
API : American Petroleum Institute
ISO : International Organization for Standardization
NLGI : National Lubricating Grease Institute
ASTM : American Society of Testing and Material
1-27