Petroleum Development Oman L.L.C.: Specification For Lift Planning and Execution

Petroleum Development Oman L.L.C.
Specification for Lift Planning and Execution
Document ID SP-2273
Document Type Specification
Security Unrestricted
Discipline UED
Owner UEQ/3
Issue Date Feb 2018
Version 0
Keywords: This document is the property of Petroleum Development Oman, LLC. Neither the whole nor
any part of this document may be disclosed to others or reproduced, stored in a retrieval system, or
transmitted in any form by any means (electronic, mechanical, reprographic recording or otherwise)
without prior written consent of the owner.
Revision:0
Petroleum Development Oman LLC Effective: Feb 2018
This page was intentionally left blank
Printed 12/02/2018 Specification Page 2

Printed copies are UNCONTROLLED.
Revision:
Petroleum Development Oman LLC Effective:
i Document Authorisation
Authorised For Issue

Revision:0
ii Revision History
The following is a brief summary of the 4 most recent revisions to this document. Details of all
revisions prior to these are held on file by the issuing department.
Version No. Date Author Scope / Remarks

Version 0 Sep-2007 Hugo den New Lift Planning /- Execution
Boogert, UEC/14 procedure – Initial Issue
Version 1 Sep-2011 Hugo den Boogert Amendments reflecting input users
UEQ/3
Version 1.1 May-12 Robin Norman Added Interim Amendment
UOP6 1709_0412_01
Version 1.2 June-15 Hugo den Boogert Added Interim Amendment
UEQ/31 1709_0615_02
Version 0 Feb-2018 Rabani, Fahad Revised entirely to SP
UEQ/31
iii Related Business Processes

Code Business Process (EPBM 4.0)
iv Related Corporate Management System (CMS) Documents

The related CMS Documents can be retrieved from the Corporate Management Portal
(CMS).
The related CMF Documents can be retrieved from the Corporate Business Control
Documentation Register TAXI.
Design: CP-117 Project engineering

Procurement: CP-129 Contracting and Procurement CoP
PR-1233 Contracting and Procurement Specification s
Lifting and Hoisting: PR-1708 Lifting and Hoisting, Inspection, Testing and Certification
Maintenance: CP-114 Maintenance Code of Practice
HSE: PL04 HSE Policy
SP-2000 Road Transport
SP-1143 Specification for Earthmoving and Construction Equipment
CP-122 HSE Management System
SP-1242 Activities within Vicinity of Overhead Power Lines
Well Engineering: PR-1312 Equipment Inspection and Certification Specification

Revision:
TABLE OF CONTENTS
1 Introduction ……………………………………………………………………………………………….. 7
1.1 Purpose ……………………………………………………………………………………………………… 6
1.2 Change to the Specification …………………………………………………................... 6
1.3 Scope …………………………………………………………………………………………………………. 6
2 Process Definition …………………………………………………………………………………….. 6
3 Role and Responsibilities ……………………………………………………………………………. 8
3.1 Operation Managers (Company) ……………………………………………………………….. 8
3.2 Appointed Person ……………………………………………………………………………………….. 8
3.3 Lifting Supervisor ………………………………………………………………………………………… 8
3.4 Operator …………………………………………………………………………………………………….. 9
3.5 Slinger and Signaller / Rigger and banks man ……………………………………………… 9
3.6 Executing party …………………………………………………………………………………………… 10
3.7 Lifting Equipment Controller ………………………………………………………………………. 10
4 Competence ……………………………………………………………………………………………….. 10
5 Definition ……………………………………………………………………………………………………. 10
5.1 Lifting operations ……………………………………………………………………………………….. 10
5.2 Lifting equipment ……………………………………………………………………………………….. 10
5.3 Lifting accessories ………………………………………………………………………………………. 10
5.4 The load ……………………………………………………………………………………………………… 11
6 Lift planning and Execution ………………………………………………………………………… 11
6.1 Site Survey ………………………………………………………………………………………………… 11
6.1.1 Risk Assessment ………………………………………………………………………………………… 11
6.1.2 Lift Plan ……………………………………………………………………………………………………… 11
6.2 Categorizing Lifting Operations …………………………………………………………………… 11
6.2.1 Routine Lifts - low rate ……………………………………………………………………………….. 12
6.2.2 Non-Routine Lifts ………………………………………………………………………………………… 12
6.3 Execution ………………………………………………………………………………….................... 13
6.3.1 Communication of Lift Plan …………………………………………………………………………. 13
6.3.2 Conducting the Lifting Operation ………………………………………………………………… 14
6.4 Lifting of personnel …………………………………………………………………………………….. 14
6.4.1 Man Riding Winches …………………………………………………………………………………… 14

Revision:0
6.4.2 Requirements of using equipment that not designed for Personal lift include... 15
7 Specific Requirement for Execution of Lifting Operation …………………………….. 18
7.1 Operating Near Overhead Electric Power Lines and Cables ………………………… 18
7.2 Night operations ………………………………………………………………………………………... 18
7.3 Lifting Over Live Plant …………………………………………………………………………………. 18
8 Handling Tubular ………………………………………………………………………………………… 19
9 Mobile crane operation ……………………………………………………………………………… 19
9.1 Daily / Pre-Use Inspections …………………………………………………………………………. 19
10 Powered Industrial Trucks ………………………………………………………………………….. 20
10.2 Operations …………………………………………………………………………………………………. 20
11 Mobile Elevator Work Platform ………………………………………………………………….. 21
11.2 Operations …………………………………………………………………………………………………… 21
11.3 The following additional requirements for mobile aerial platform ............ 21
12 Learning and Record …………………………………………………………………………………… 24
13 Application and Step-out ……………………………………………………………………………. 24
13.1 Application ……………………………………………………………………………………………....... 24
13.2 Step-out and Approval ………………………………………………………………………………… 24
14 Appendix 01 ……………………………………………………………………………………………….. 25
15 Appendix 02 ……………………………………………………………………………………………….. 28
16 Appendix 03 ………………………………………………………………………………………………... 29

Revision:
1 Introduction
1.1 Purpose
This document provides a specification to be used for lifting operational practices.
The key to safe lifting operation is having qualified personnel using the correct equipment in
a safe manner. This specification will outline the issues relating to the selection of the
correct people for the task. It will describe the operational practices to be used by these
people as part of a safe and effective crane and rigging program.
This specification prohibits a person from riding or travelling on the load, lifting
hook, sling, platform or other lifting medium.
This specification doesn’t cover earth moving machinery.
1.2 Changes to the Specification

Responsibility for the upkeep of the Document shall be with the Functional Production
Manager UEQ, the Owner. Changes to this document shall only be authorised and
approved by the Owner.
Users of the Document who identify inaccuracy or ambiguity can notify the Custodian or
his/her delegate and request changes be initiated. The Requests shall be forwarded to
the Custodian.
The Document Custodian on behalf of the Document Owner shall ensure review and re-
verification of this procedure every 5 years.
1.3 Scope
This specification applies to all functions performing lifting or lowering operations, rigging
operations in all company locations. And it is applicable to all lifting categories.
2 Process Definition
Company : Petroleum Development Oman LLC (PDO)
AP : Appointed Person
ABA : Accrediting Bodies Association
IPAF : International Powered Access Federation
LEC : Lifting Equipment Controller
MEWP : Mobile Elevator Work platform
NPORS : National Operator Registration Scheme
PIC : Person in Charge
RTITB : Road Transport Industry Training Board
ALARP : As Low As Reasonably Practicable
RCI : Rate Capacity Indicator
RCL : Rate Capacity Limiter
PTW : Permit to Work
SWL : Safe Working Load

Revision:0
3 Role and Responsibilities
3.1 Operation Managers (Company)

Operation Managers shall ensure in all cases where lifting equipment is being
Used, that:
 All risks arising from operations involving lifting equipment are suitably and sufficiently
assessed by a competent person and appropriate control measures implemented.
 All lifting operations are suitably planned, supervised and carried out in a safe manner.
 Planning of a single lift or series of lifts shall address the risks identified by the risk
assessment and that appropriate control measures have been implemented (safe
systems of work, lifting plans etc.)
 All relevant information, training and instruction are given to users of lifting equipment
and they are competent to carry out those tasks.
 All persons using lifting equipment shall work within the agreed safe working practices,
reference information, instruction and training given.
 There is a system for the reporting and removing from use any lifting equipment that
has developed a fault or defect.
3.2 Appointed Person
A person who have been appointed or been given the responsibility for planning lifting
operations shall have sufficient technical, practical and theoretical training, knowledge and
experience of the work they are likely to safely plan /assess the lift.
And he shall:
 Have a valid ABA certification as appointed person.
 Be responsible for planning lifting operation.
 Be capable of identifying the hazards and risks associated to lifting operations within
their area of work or the environment where the lifting operation will take place.
 Be able to select the correct lifting equipment for the work. Understand the
characteristics of the lifting equipment they are selecting and the nature of the work it
will be carrying out.
 Carry out and document risk assessments (lifting operation) or site surveys; have the
ability to communicate their findings to those involved in and affected by the lifting
operations.
 Be able to create method statements or lifting plans and implement safe systems of
work for lifting operations.
 Where appropriate seek additional support and expertise including the use of external
specialists to assist them with the planning of lifting operations.
 Only approve routine lift plans.
3.3 Lifting Supervisor
Persons who have been authorized to supervise lifting operations shall:

 Have sufficient technical, practical and theoretical training, knowledge and experience
of the work being carried out.
 Have a valid ABA certification as lifting supervisor or a crane supervisor.
 Be briefed and instructed on the outcomes of the risk assessment and fully understand
the requirements of the lifting plan for the lifting operation to be carried out and an
Revision:
understanding of all those involved in the task.

 Supervise all non-routine lifting operations.
 Monitor a sufficient number of lifting operations to ensure correct working practices are
being followed.
 Where appropriate direct lifting operations, offering clear instructions to those involved.
 Be able to assess changes in circumstances e.g. ground conditions, and where
appropriate stop a lifting operation if the risk is unacceptable or if it is considered unsafe
to carry on.
 Referring the concerns to their manager, competent person or person responsible for
planning lifting operations.
 Conduct a tool box and discuses the 10 questions for safe lift.
3.4 Operator
Shall:
 Not attempt any lifting operation or use lifting equipment, without prior
training/assessment, guidance and appropriate supervision or which is beyond the level
of their competency.
 Have a valid ABA certification as an operator for the specific machine.
 Ensure that both routine and non routine lifting operations are not undertaken without a
suitable and sufficient risk assessment being carried out by a competent person.
 Ensure they fully understand the lifting equipment, be familiar with how it operates and
the proposed lifting operation(s) they have been authorized to do and that safe systems
of work, training, guidance and advice are followed at all times.
 Carry out pre-use checks of lifting equipment prior to use, to ensure there are no
obvious visual defects.
 Have an understanding of the emergency specification relating to lifting equipment in
use and take part in training and periodic drills, where appropriate.
3.5 Slinger and Signaller / Rigger and banks man
Shall:
 Not attempt any lifting operation or use lifting equipment, without prior
training/assessment, guidance and appropriate supervision or which is beyond the level
of their competency.
 Have a valid ABA certification as Slinger and Signaller or Rigger and banks man
 Carry out pre-use checks of lifting equipment prior to use, to ensure there are no
obvious visual defects.
 Choose the correct lifting accessories for the lift.
 Inspect the load to be lifted.
 Place slings/accessories on the load to be lifted.
 Give signals to the crane operator.
 Move load in a safe manner.
 Remove slings and accessories.
 Inspect slings and accessories (Post check).
 Play the role of lifting supervisor in routine lift ONLY.

Revision:0
3.6 Executing party
 To identify lifting parameters needed to execute the work.

 To prepare a lift plan and to ensure that a risk assessment is carried out.
 To source a certified lifting equipment from registered contractor/operator under their current
contract.
 To constantly monitor the approved plan and identify improvement for future work.
3.7 Lifting Equipment Controller
Every site shall appoint a competent lifting Equipment Controller and shall:
 Have a valid ABA certification as LEC.
 Issue lifting accessories.
 Accept returned accessories.
 Maintain loft register.
 Ensure lifting equipment is certified.
 Be responsible for loft and quarantine area.
4 Competence
- COMPANY employee or contractor personal shall not perform or participate in lifting
operations unless they are trained and certified to a standard that meet the minimum
acceptable competency as defined by COMPANY specification SP-1157.
- The minimum required level of competence is ABA accreditation or IPAF for mobile
elevator only.
- Anyone intend to participate in any lifting operations shall have a valid ABA card that
indicating his competency. Refer to section 2 Role and responsibilities.
- Where an individual has not yet meet the defined level of competency or if under
development plan shall only working under direct supervision at all time.
5 Definition
5.1 Lifting operations
A lifting operation is an operation concerned with the lifting and lowering of a load. A load is
the item or items being lifted which could include material or people. A lifting operation shall
be performed manually or using lifting machine.
5.2 Lifting equipment
Lifting equipment includes any equipment or machinery used at work for lifting or lowering
loads or people. There is a wide range of lifting equipment in the industry. Lifting equipment
examples are: hoist devices, cranes, a tele handler, fork lift trucks, an aerial work platform
(MEWPs), boom lift truck, lifting beam, containers, sheave, etc.
5.3 Lifting accessories
Lifting accessories means a component or equipment are attached to the lifting machinery,
allowing the load to be held, which is placed between the machinery and the load or on the
load itself. These accessories include amongst others chains, ropes, slings, shackles,
eyebolts and open wedges, etc.

Revision:
5.4 The load
The load includes any material and people (or any combination of these) that is lifted by the
lifting equipment. Loads are often provided with permanent or semi-permanent fixed or
attached points for lifting. In most cases, these are considered to be part of the load.
Examples of loads include:
 Loose bulk materials
 Sacks, bags, pallets and stillages
 Discrete items (such as a large concrete block)
 Machinery and any permanently attached lifting eyes
 Lugs fixed to its side.
6 Lift Planning and Execution

Before performing any lifting, the executer party shall plan and prepare for the task. They
shall make sure that they know where they are going, that the area is clear of obstacles
and they have a good grip on the load. This includes training of the workers on how to
handle loads correctly.
6.1 Site Survey
It is essential that a survey be conducted to establish details of load to be lifted i.e. weight,
size, type of lifting lugs etc., details of the ground conditions, lifting route the access route.
The survey shall be completed by a competent person(s).
6.1.1 Risk Assessment

The site survey is an ideal time to begin a risk assessment of the proposed lifting
operations that will be carried out. The aim of the risk assessment is to prevent incidents
and/or accidents that arise from hazards during the lifting operations. With the identified
hazards, the risks posed by these hazards can be reduced to as low as reasonably
practical through the implementation of control measures, using the principle of the
hierarchy of controls.
6.1.2 Lift Plan

A competent person shall only initiate the lift plan. A lift plan shall be prepared or identified
for every lift. The lift plan comprises amongst others:
 Calculations / drawing.
 Equipment required details.
 Personnel required and their particular roles.
 Risk assessment.
 Step-by-step instructions with specific task risk assessment.
 10 questions for a safe lift.
 Communication methods to be used.
 Minimum required lift planning data is shown on the acceptable lifting plan format at
Appendix 01).
6.2 Categorizing Lifting Operations
There are generally two types of lift, Routine and Non-Routine. Categorizing the type of lift
before planning the lift and documenting in a lifting plan is critical because it allows for the

Revision:0
proper assessment of the amount of risk present in the lifting operation and the level of
control required in mitigating the risks involved.
6.2.1 Routine Lifts - low rate

Routine lifting operations shall be executed under a routine lift plan. These plans shall
clearly define the limitations on the loads, lifting methods and areas of operation. A Risk
Assessment will be required in each case, and authorized prior to commencement. Prior to
any lifting operation commencing, a review of the lift plan shall be conducted. A Routine Lift
is a lift which conforms to the following factors:
- Routine crane operations
- Repetitive lifting operations using the same equipment (eg. drilling activities), same
competent operator, and with same Loose Lifting Equipment.
- Gross load represents less than 50% of the load chart at working radius with gross load
is less than 5 tones.
- Within the normal operating parameters of the crane.
- Suitable environmental conditions.
- Load has known and evaluated weight, shape and centre of gravity.
- Standard rigging arrangements.
- Centre of gravity has been identified and it is below the lifting point.
Note: Routine lifting operations require the above factors to be considered but this list is
not exhaustive. The risk of each individual lift shall be separately considered prior to
classifying the lifting operation as a routine one.
6.2.2 Non-Routine Lifts

Non- Routine lifting operations will require a more detailed Lifting Plan that is containing all
of the elements as described within these specifications. The plan shall be approved by
company lifting department prior to commencement of any Lifting Operation and any
deviation (MoC) requirement identified from the plan, shall also get the approval of the
company lifting department prior to commencement of the lifting operation.
6.2.3 Non-Routine simple lift – Medium Rate:

- Gross load is equal to 5 tonnes and less than 75 tones with gross load represent less than
75% of the load chart at the working radius.
- Single lifting appliance.
- Unlikely to be affected by changing environmental conditions.
- Standard rigging arrangements.
- The lift in an area with restricted head room for the lifting appliance.
- The exerted load applied to the ground between 40% - 59% of the documented site Ground
Bearing Capacity.
- The lift blind or conducted within a confined space, trench or excavation.
- The load has an offset CoG or has a large sail area.
- The load has a CoG above the lifting points or a high CoG or the potential to become
unstable.
6.2.4 Non-Routine complex lift – High Rate:

- The lift involves lifting or lowering personnel.

Revision:
- Gross load is greater than 75 tones or gross load represents more than 75% of the load
chart at working radius.
- Use of two or more Lifting Appliances (tandem lifting).
- Over or in sensitive areas – active or energized hydrocarbon-containing process
equipment, near overhead electrical power lines or within restricted area.
- Transferring the load from one lifting appliance to another (tailing lift).
- In environmental conditions likely to affect equipment performance.
- Load with unknown / difficult to estimate weight and / or centre of gravity.
- Load is special and / or expensive whose loss would have a serious impact on
production operations.
- Non-standard rigging arrangements.
- The crane will move position whilst lifting a load.
- Using a fixed lifting system (overhead crane, runway beam or davit etc.) is the
percentage of utilization above 95%.
- The exerted load applied to the ground between 60% - 75% of the documented site
Ground Bearing Capacity.
- Lifting Over Live Plant see Sec 6.3
Note: Non-Routine lifting operations require the above factors to be considered but this list
is not exhaustive.
6.3 Execution
Lifting shall not be carried out unless all risks have been documented and mitigated /
reduced to ALARP, following controls shall be considered in all lifting activities:
 A defined lift categorization system, utilizing at least three categories, shall be used to
identify the complexity of lifting operation.
 All lifting operations shall have a documented and approved risk assessment and lifting
plan
 Loads shall be positively connected to the lifting equipment / appliance
 Ground Bearing Pressure (GBP) of loads / lifting equipment shall be documented on
lifting plans and shall not exceed 75% of the site Ground Bearing Capacity (GBC)
 Overturning/load integrity/need for tag lines.
 A methodology to disconnect the lifting tackles at elevated level.
 Contingency and rescue plan is in place.
6.3.1 Communication of Lift Plan

Prior to starting of lifting operations the lifting supervisor shall hold a Toolbox Talk with all
personnel is involved in the lift. Application of the ‘10 questions for a safe lift’ to the lift shall
be covered during the Toolbox Talk (Appendix 02).
The lifting supervisor shall be clearly identified and made known to all members of the lift
team and personnel in the proximity.
Signaller is responsible of lifting movement by maintaining the communication with crane
operator and slinger. Signaller shall be identified by wearing visible vest.
All personnel involved in the lifting operation shall be cleared with their individual
responsibilities clearly allocated.
All personnel shall have the opportunity to review the findings of the risk assessment and
the details of the Lift Plan to ensure that everyone clearly understands and agrees with the
methods and control measures to be used.

Revision:0
6.3.2 Conducting the Lifting Operation

Lifting operations shall be conducted in strict accordance with the approved Lift Plan. Any
variation from the agreed Lift Plan shall result in the job being stopped and re-approved to
ensure continued safe operation. (Management of Change specification)
The Lifting Appliance Operator shall obey an emergency stop signal at all times, no matter
who gives it.
The appropriate load-radius chart for the Lifting Appliance configuration in use shall be
available and visible to the operator in case the RCI/RCL is not available.
Load to be lifted shall be confirmed to be free to lift and within the rated capacity of the
Lifting Equipment and attached by means of suitable Lifting Accessories.
The Operator of the Lifting Appliance shall not leave the operating controls while the load is
suspended.
Certified equipment shall be only used. All lifting equipment shall comply with SP-1708.
6.4 Lifting of personnel
 Prior to starting any Lifting Personal Operation, minor variations shall be documented to
take account of current conditions (e.g.) wind speeds, wave height, position of people
and deck layout).
 The equipment used for lifting personnel shall be specifically designed for man lift
purpose i.e. Mobile Elevator Platform and shall be certified and shall not be used for
any other purposes and supported by thorough risk assessment.
 All involved personnel shall be qualified and understand the lift plan and the risks
involved.
 Lifting supervisor up/set down areas shall be of an adequate size and free from hazards
affecting access and egress from the carrier.
 Environmental and other limits for personnel lifts shall be set out in the lift plan with
clarity on where they differ from limits for other lifting.
 In case of any changes in job scope or conditions, the job shall be made safe and
stopped, risks re-assessed and a pre-job meeting executed before the job is restarted.
Examples of such changes include operating/weather conditions, day or night
operations or changes in personnel or equipment involved.
 Personnel lifts shall only be conducted where there is line of sight (full visibility) between
the equipment operator and signaller, and between the signaller and the person being
lifted.
6.4.1 Man Riding Winches

Ideally, Man riding winches shall be avoided and replaced for other suitable, engineered
and certified alternatives. However if it is unavoidable, and used under the PTW, then the
following requirements shall apply for man riding winches:-
 Shall be restricted to 150Kg.
 A communication with all involved parties during operation.
 Shall be equipped with non-rotating wire rope.
 Shall have two brakes.
 Shall have limiting switches for High and Low levels.
 Shall not exceed monkey board level.
 No freefall system.
 Shall have emergency lowering system

Revision:
 Shall have Slack line prevention system

 Shall be certified.
Note: All other operations shall be ceased during the Man riding winch operation. The
winch shall be operated by a competent person only.
6.4.2 Requirements of using equipment that are not designed for Personal lift
Using lifting equipment which has not been specifically designed for lifting people i.e.
cranes shall only occur in exceptional circumstances, e.g. for rescue purposes or there is
no other alternative to access. And shall be specifically approved by COMPANY Lifting
Engineer and supported by thorough risk assessment, Job Hazard analyzes.
lifting or lowering personnel shall be rated as non routine High-Rate .The plan shall be
approved by the COMPANY lifting engineer prior to commencement the lifting operation
and any deviation requirement identified from the plan, shall also get the approval of the
COMPANY lifting Engineer prior to commencement of the lifting operation.
A rescue plan shall be prepared for all personnel lifts as part of the lift plan. All equipment
required to implement the rescue plan shall be readily available prior to and during the lift.
Rescue plans shall be practiced at regular intervals. Note that rescue operations can
introduce their own hazards; therefore the planning and execution of rescue exercises
requires particular care and attention including additional risk assessments. A test lift
without personnel shall be carried out where there is confined access, potential for
snagging or other hazard.
6.4.3 General requirement

 Suspended baskets only to be used in exceptional circumstances, when there are no
alternatives and has to be approved by the COMPANY operation manager in writing.
 Lifting of Personnel shall only be conducted within daylight hours, unless approved by
the operation manager in consultation with the Lifting Engineer
 Lifting of personnel regardless of lift environment shall be considered as a high risk
operation and be categorized as complex lift high rate.
 Lifting of personnel shall only be used when it is not practicable to gain access by a less
hazardous means, rigorously risk assessed and fully managed in accordance with strict
specification s.
 Lifting of personnel shall only be carried out when the risk of personnel falling from a
Carrier, or being crushed, trapped or struck while being transported in a carrier has
been mitigated to as low as reasonably practicable.
 Rescue plan shall be developed, implemented and effectively communicated.
 Rescue equipment shall be readily available and operational at the lift location before
the Lifting Operation starts.
 Lifting Equipment for Lifting Personnel shall be thoroughly examined periodically
examination at least every 6 months.
 Roles and responsibilities are assigned and coordinated.
 Radio communication shall be established prior to commencing Lifting Operations.
 Procedure is in place for radio communication failure.
 Visual contact is maintained throughout Lifting Operation.
6.4.4 Crane shall be

 Designed in accordance with EN: 13000.
 Meet the requirement of EN: 7121-2-3.
Revision:0
 Crane shall have valid inspection certificate at least six month.

 Crane shall be designed to lift or to lower at least a load equal to 125 % of the rated
capacity.
 Brakes shall apply automatically when the driving power supply or the power supply to
the control circuit is interrupted in any way (e.g. emergency stop) and stop the man
basket within a distance of 0.1m.
 Brakes shall be designed and manufactured in such a manner as to ensure smooth
application so that the man basket is not subject to any dangerous stresses even under
emergency conditions.
 Crane is fitted with two distinct mechanisms for preventing the load from falling, one of
which shall be self-acting/fail safe. Any free-fall possibility shall be locked out.
 Wire rope and termination shall be in accordance with EN 13411-6, non rotational type
only.
 Rope drums shall be grooved. There shall be a minimum of three dead turns on the
drum in its lowest position.
 The hydraulic power system shall conform to EN 982.
 Pressure limiting valve(s) shall be fitted in every hydraulic circuit to provide protection
against excess of pressure.
 Load bearing hydraulic cylinders shall be fitted with a device to prevent unintended
movement caused pipe/hose rapture.
 Where two cylinders operate in parallel, a valve system shall be provided to ensure that
in the event of loss of pressure to one cylinder the other cylinder shall be protected
against overload.
 The maximum operating speed of man basket s shall not exceed 0.5 m/s.
 Crane shall have a load limiting device, which at a load 110 % of the sum of the rated
capacity and the weight of the man basket shall prevent the hoist from starting.
6.4.5 Crane Operator shall

 Be competent for the task to a standard recognized by the Lifting Engineer.
 Be briefed in the operation to be performed.
 Check prevailing weather conditions, ((e.g.), wind speed, sea-state) to conform to
criteria listed in the specification s/lift plan.
 Perform a trial lift without personnel prior to the actual lift.
 Perform a Pre Use Inspection of the crane prior to the Lifting Operation.
6.4.6 Passengers being lifted shall

 Be briefed clearly by the lifting supervisor.
 Have been trained and / or have experience of personnel lifting.
 Have been trained in self-rescue from height equipment.
 Have been briefed on all aspects of personnel lifting.
6.4.7 Basket shall be:

 Suitably designed to a standard recognized by the Lifting Engineer
 Constructed and certified for the purpose of personnel lifting.
 Marked with a SWL, that it is suitable for personnel lifting and the maximum number of
Revision:
passengers Securely attached to the crane, ((e.g.), by safety pin, four part shackle,
positive lock hook)
 Fitted with a redundant sling, acting as secondary retention.
 Fitted with internal handrails to prevent hands / fingers being trapped if the basket
swings against an obstruction
 Fitted with a roof to protect personnel, if there is a risk of falling objects
 Fitted with slip resistant floor
 Fitted with internal anchor points for safety harnesses Fitted with inwardly opening
doors and have a locking mechanism to prevent inadvertent opening
 If required Personnel Baskets shall fitted with integral ladder for access / egress.
6.5 Working platforms (non-integrated) on forklift trucks
Forklift trucks are primarily intended for lifting materials not people. Hence non-integrated
working platforms are not permitted under any circumstance. However, only integrated one
is allowed.
6.6 Reacting to changing conditions
All critical lifting parameters such as for instance weather, visibility, ground stability and
slope, surrounding operations and installations, site access and egress, Lifting Equipment,
personnel and so on, shall be identified during the risk assessment and preparation of the
Lift Plan.
The lifting supervisor shall ensure that these conditions are monitored as lifting operations
proceed to ensure continued safety.
If, as part of the operation and maintenance of equipment, the computer system for
instance shuts down the operation, the load shall be placed on the ground and a new lift
plan shall be developed, eliminating the condition that caused the shut down.
Specification for recovering and landing the load in the event of the lift being aborted shall
be clearly identified.
6.7 Assembly and De-assembly of Mobile Hydraulic, Crawler Cranes & Tower Cranes
The Assembly and De-Assembly of cranes is correctly classified as” High Risk Activity”.
Many accidents and indeed in many cases there are more accidents resulting in injury and
fatality during these 2 phases of a lifting operation than what occur during the actual lifting
process.
Assembly and De-Assembly present many challenges and generate many hazards and
associated risks. During these phases of any lifting operation extreme caution and vigilance
are required. Much heavy work and working at height is required, particularly where larger
capacity cranes are in use. Careful documented planning of Hazard and Risk Analysis is
required.
De-assembly also brings the added factors of rushing at the end of a lift to get clear of the
site, equally after a lift is complete and in many cases the crane operator is left to his own
devices and alone to
Complete the task, folding up the Fly – Jib on a small hydraulic is every bit as dangerous as
taking of the luffer on a large crawler. Whilst all phases of a lifting operation require focus,
vigilance, monitoring and control, the elements of Assembly and De-Assembly are very
easily overlooked and taken for granted. Appointed Persons/ Lift Supervisors shall ensure
that the lifting team is alert and familiar with all hazards, associated risks and implemented
control measures. Once the assembly is completed the crane shall be thorough examined
followed by load test.

Revision:0
7 Specific Requirements for Execution of Lifting Operations

7.1 Operating Near Overhead Electric Power Lines and Cables
If any part of a crane, including rope, slings or load, touches or even approaches overhead
electric lines or cables there is a serious risk of fatal accident. The work shall be performed
so there is no possibility of the crane, load line or load becoming a conductive path.
In general, the LIFTING SUPERVISOR shall ensure that the crane does not operate within:
15 meters plus the maximum achievable boom length, measured horizontally, for overhead
lines on steel towers; or 9 meters plus the maximum achievable boom length, measured
horizontally, for overhead lines on wood, concrete.
Additionally, the lifting supervisor shall consider:
 Isolation of electricity if possible
 Contacting the electricity provider
 Weather – effect on the safe working zone
 Use of physical barriers e.g. goal posts
Cranes shall not be used to handle materials stored under electric power lines unless any
combination of boom, load, load line or machine component cannot enter the prohibited
zone. Overhead lines and other electrical apparatus shall be considered live unless
declared ‘dead’ and ‘safe’ by the Line Operator. Crane Operators shall not rely on the
coverings of wires for their protection.
Where the possibility of contact with energized power lines exists then durable signs shall
be installed at the operator’s station and on the outside of the crane warning that
electrocution or serious bodily injury shall occur unless minimum clearances are maintained
between the crane or the load being handled and energized power lines.
See also SP-1242 Activities within vicinity of overhead power lines, which have to be strictly
adhered to.
7.2 Night operations
Generally Night lift operation to be discouraged, only allowed after specific permission by
COMPANY operation manager. Following precautions have to be considered:
 Lifting by night or when there is not sufficient visibility is not allowed for complicated lifts
and tandem lifts. They are not to be carried at by night or shall not start when the lift
cannot be completed before dark.
 All lifts at night which shall be treated as non-routine.
 Adequate lighting has to be ensured. All access and escapes to be clearly illuminated.
 Ensure emergency lighting as a backup is available. Assembly point is clear and
defined.
 Signalling arrangements to be reviewed (instead of hand signals use radio).
7.3 Lifting Over Live Plant
Lifting over live plant is defined as a complex lifting operation, where there is a risk of the
load, lifting appliances and/or lifting accessories impacting, damaging and/or rupturing live
plant. Also Live plant is defined as equipment containing hazardous, pressurized,
energized or strategic resource, for example: pipes or vessels containing hydrocarbons,
electrical cables or primary power generation units such as turbines and generators and
their exhaust systems.

Revision:
- Lifting over live plant shall not be carried out unless all risks have been documented
and mitigated/reduced to ALARP and it has been established that there is no other
feasible option
- All lifts executed over live plant shall have an operational contingency plan
documenting how to control the effects of any loss of containment, fires, explosion,
electrocution, loss of production, environmental contamination etc.
- Lifting over live plant operations shall fall within the highest rate of category in the
system (critical lift)
- Defined exclusion zones shall be documented, applied and be relative to the identified
risks
8 Handling of tubular
Executer party is responsible to select the right means to lift, handle and transport tubular.
All controls i.e. lift plan, risk assessment… etc shall be in place prior any operation.
Key elements and practices for the safe operation of slinging tubular or tubular bundles are:
 Only tubular of the same diameter or size and about the same length shall be bundled
together.
 Tubular shall always be slung with two slings, each of the same length and of the same
SWL
 Always secure the tubular if they are subjected to transport by forks.
 Slings shall be placed positioned at equal distance (approximately 25% of total length)
from the ends of the load. They shall be double wrapped and choked around the tubular
either when using wire rope slings or webbing slings.
 Care shall be taken to ensure that the chocking eyes are placed on the same side of the
tubes to avoid twisting of tubes if chocked from opposite directions.
 The sling shall be of sufficient length to ensure that the choke is on the sling body,
never on the sling splice, fittings, tag, eye or at the base of the sling eye or fitting
 Excessive long tubular bundles shall have a tag line attached. This shall be subject to a
JHA
 Whilst loading, consideration shall be given to the installation discharging sequence
 Ensure thread protectors and end caps are securely fastened
 Slings shall not cross under the load to avoid damage to the sling.
 Prior to making any lifts, the release of rigging shall be considered. Precautions are
 Are required to prevent personnel from being trapped between tubular.
9 Mobile Crane Operations

9.1 Daily / Pre-Use Inspections
These inspections shall be performed and documented by a qualified operator prior to first
use each day or shift the truck is used. These checks ensure that equipment is working
correctly by carrying out function tests prior to any lifting operations.
A VALID INSPECTION CERTICATE SHALL BE AVAILABE IN THE EQUIPMENT.
 During operation, the crane shall not be left unattended.

 The lifting supervisor shall obtain information on wind conditions prior to starting and
during a lifting operation.
 The lifting supervisor shall ensure that the ground (soil test), or any means of support,
Revision:0
can sustain loads imposed by the crane

 Side loads shall be avoided.
 When sitting a crane, point loads through the outrigger / stabilizer beams and jack pads
shall be spread over a sufficient area to support the outrigger pad and to prevent the
crane overturning or becoming unstable.
 While in transit the boom shall be retracted and carried in line with the direction of
motion and the superstructure secured against rotation (or the boom placed in a boom
rack mounted on the carrier).
 The empty hook shall be lashed or otherwise restrained so that it cannot swing freely.
 If the crane has a telescopic boom it shall be set to the fully retracted position.
 Counterweights shall be properly secured.
 Ensure wheel chocks are used to block movement on slopes.
 Cranes shall not be used for dragging or pulling a load.
 For normal operation wind conditions shall not exceed 12.5 m/s (24 Knots).
 At commencement of the first lift the Lifting Appliance Operator shall carefully check
the operation of the hoist brake to ensure no slippage occurs.
10 Powered Industrial Trucks including Fork Lift Trucks (FLTs)

10.2 Operations
During operations, the Operator shall:

 Drive at speeds appropriate for the existing conditions (space, load, lighting, surface
conditions, etc.) and at or below posted limits
 Keep all parts of the body inside the Operator compartment during operations
 Not start or operate the truck or any of its attachments from any place other than from
the Operators position.
 Ensure other personnel are not in the swing radius prior to performing turning
manoeuvres.
 Sound the horn when approaching cross aisles, doorways and other locations where
pedestrians shall step into the path of truck travel.
 Verify sufficient headroom under overhead installations, lights, wiring, pipes, sprinkler
systems etc
 Ensure they are driven on suitable surfaces. Road humps and rough or soft surfaces are
to be avoided.
 Movement with loads in excessively raised positions shall not be carried out to avoid the
danger of toppling, especially on uneven surfaces and while cornering
 Shall only be used for loads, which can be carried safely on the forks or attachments
fitted.
 Long tubes shall be carried using appropriate OEM approved attachments. Loads shall
not be suspended from forks by means of slings.
 Authorized personnel shall only operate powered industrial trucks

Revision:
 Equipment shall not be loaded beyond its rated load (capacity).

 Trucks shall not be driven up to anyone standing in front of an object.
 Only approved industrial trucks shall be used in areas classified as hazardous locations.
 Driving rough terrain FLTs on public roads shall be kept to a minimum. When public road
travel is necessary, fork arms shall be removed, folded or protected in some way so that
they do not present a hazard to other road users. Where this is not possible, forks shall
be painted or otherwise made highly visible
 Rough terrain FLT Operators shall wear seat belts while driving their vehicles.
11 Mobile Elevator Work Platforms

11.2 Operations
Personnel lifting devices and mobile aerial platforms shall be operated according to
applicable
Government requirements and manufacturers’ instructions. The following practices shall be
followed:
 Determine through JHA process that the proposed personnel lifting operation is either
the least hazardous method or the only method available to position personnel so that
an operation can be accomplished.
 Personnel shall:
- Keep all parts of the body, tools, and equipment inside the work platform periphery
during raising, lowering, and travelling operations
- Hold onto a moving platform using both hands
- Secure tools and other objects in canvas bags or by other methods so that both hands
are free and do not present a snagging hazard. Alternate methods of tool delivery
beside personnel lifting devices shall be investigated
- Wear fall protection with a lanyard attached to an authorized lanyard anchorage point.
Attach only one (1) lanyard per lanyard anchorage point
- Detailed technical operating specification s describing personnel lifting device
operation, emergency steps, communication requirements, and special requirements
shall be prepared
- Personnel lifting device or mobile aerial platforms shall not be loaded beyond its rated
load (capacity).
- Consideration shall be given to prevailing environmental conditions (e.g. wind as
indicated by manufacturer), as well as aspects of the device (e.g. sail area) before
commencing operations
11.3 The following additional requirements shall be followed for mobile aerial platform
operations:
 Survey the area for applicable hazards such as:

- Overhead obstructions and high-voltage conductors;
Revision:0
- Debris, bumps and loose obstructions, drop-offs, holes, ditches, open earth fills,
obstructed path of travel, unstable footing, and other possible hazardous conditions.
 Electrocution Hazards
- For work on or near electrical distribution and transmission lines, mobile aerial
platforms shall be operated in accordance with the applicable national and or local
standard e.g. ANSI/SIA ASME standard
- Note: for non-insulated platforms it is recommended that the following sign is posted:
‘This machine is not insulated and does not provide protection from contact or
proximity to electrical current’
- Maintain safe distance from electrical lines, apparatus, or any energized (exposed or
insulated) parts according to the Minimum Safe Approach
- Distance (MSAD) as shown in Table 1-1;
Table 1-1. Minimum Safe Approach Distances (M.S.A.D)

Voltage Ranges Minimum Safe Approach
Distances
(Phase to Phase)
in Feet (Meters)
0 to 300V AVOID CONTACT
Over 300V to 20KV 10 (3)
Over 50KV to 200KV 15 (5)
Over 200KV to 350KV 20 (6)
Over 350KV to 500KV 25 (8)
Over 500KV to 750KV 35 (11)
Over750KV to 1000KV 45 (14)

DO NOT MANEUVER MACHINE OR PERSONNEL INSIDE PROHIBITED ZONE (MSAD).

ASSUME ALL ELECTRICAL PATRS AND WIRING IS ENERGIZED UNLESS KNOWN
OTHERWISE
- Insulated mobile aerial platforms shall be tested and inspected in accordance with the
applicable standard e.g. BS EN 61057 or ANSI/SIA ASME standard;
- Stow boom and shut off all power before leaving machine
- When two or more persons are in the platform, the Operator shall be responsible for
all machine operations
- Do not place boom or platform against any structure to steady the platform or to
support the structure
- Keep both feet firmly positioned on the platform floor at al times. Never use ladders,
boxes, steps, planks, or similar items on platform to provide additional reach
- Never use the boom assembly to enter or leave the platform
- Do not use machine as a ground for welding
- When performing welding or metal cutting operations, precautions shall be taken to
protect the chassis from direct exposure to weld and metal cutting spatter
- Do not refuel the machine with the engine running
- Charge batteries only in a well ventilated area
Revision:
 Tipping Hazards
- The user shall be familiar with the surface before driving. Do not exceed the allowable
side slope and grade while driving
- Personnel Platforms/Carriers shall not be elevated whilst on a sloping, uneven, or soft
surface. Personnel shall not be driven with the platform elevated
- Before driving on floors, bridges, trucks, and other surfaces, check allowable capacity
of the surfaces
- Never exceed the maximum platform capacity. Distribute loads evenly on platform
floor
- Do not raise the platform or drive from an elevated position unless the machine is on
firm, level surfaces and evenly supported
- Keep the chassis of the machine at least 2 ft. (0.6m) from holes, bumps, drop-offs,
obstructions, debris, concealed holes, and other potential hazards on the floor/surface
- Do not push or pull any object with the boom
- Never attempt to use the machine as a crane. Do not tie-off machine to any adjacent
structure
- Do not operate the machine when wind conditions exceed 12.5 m/s (24 Knots) or as
prescribed by manufacturer, local legislation and or specification s
- Do not increase the surface area of the platform or the load. Increase of the area
exposed to the wind will decrease stability
- Do not increase the platform size with unauthorized deck extensions or attachments
- If boom assembly or platform is in a position that one or more wheels are off the
ground, all persons shall be removed before attempting to stabilize the machine. Use
cranes, forklift trucks, or other appropriate equipment to stabilize machine and
remove personnel
 Crushing and Collision Hazards

- All operating and ground personnel shall wear approved headgear
- Check work area for clearances overhead, on sides, and bottom of platform when
lifting or lowering platform, and driving
- During operation, keep all body parts inside platform railing
- Use the boom functions, not the drive function, to position the platform close to
obstacles
- Always post a lookout when driving in areas where vision is obstructed
- Keep non-operating personnel at least 6 ft. (1.8m) away from machine during all
driving and swing operations
- Limit travel speed according to conditions of ground surface, congestion, visibility,
slope, location of personnel, and other factors, which shall cause collision or injury to
personnel
- Be aware of stopping distances in all drive speeds. When driving in high speed, switch
to low speed before stopping
- Travel grades in low speed only
- Do not use high-speed drive in restricted or close quarters or when driving in reverse
- Exercise extreme caution at all times to prevent obstacles from striking or interfering
with operating controls and persons in the platform
- Be sure that operators of other overhead and floor level machines are aware of the
aerial work platforms presence
- Disconnect power to overhead cranes
- Warn personnel not to work, stand, or walk under a raised boom or platform

Revision:0
- Position barricades on floor if necessary.
12 Learning and Record

After completing the lifting operation, everyone involved in the lift shall have the opportunity
to discuss and make improvements to the Lift Plan. Any learning points noted on the plan
shall be reviewed by a competent person and, where appropriate, action taken. Learning
points shall include feedback on equipment effectiveness, lifting techniques, personnel, etc.
13 Application and Step-out

13.1 Application
This Lift planning specification is applicable to all lifting operations including the COMPANY
and its contractors. As such, this document is mandatory and shall be adhered to by all
parties, involved in lifting operations.
14 Step-out and Approval

Any step-out from this specification shall be addressed to the COMPANY lifting department
in writing. It will be reviewed and authorized if the deviation in exceptional circumstances.

Revision:
15 Appendix
15.1 Appendix 1, Lift plan
Petroleum Development Oman

L.L.C.
METHOD STATEMENT FOR LIFTING OPERATION
PROJECT
ACTIVITY
CONTARCTOR
Lifting Category Routine / Non routine Location / RIG No
PERMIT NO: Total weight
To ensure the safety of the personnel/ equipment/ asset involved in

OBJECTIVE
lifting activities
 Deploy individuals with valid certifications (Crane operator, lifting
MAN POWER supervisor & riggers)
 A designated lifting supervisor (person in charge PIC and banks
man)
Banks man / Signaller: Co-ordinate the lifting movements and

maintains radio- and/or visual communication with crane operator and
persons close to the load
Slinger /Rigger: Inspect the rigging, select rigging to suit the load,
install the equipment and connect/disconnect the load
RESPONSIBILITIES Lifting supervisor (PIC): Co-ordinate and control all aspects of lifting
operations on site. ( Banks man can be the lifting supervisor if he is
competent)
Crane Operator: Pre-use inspection of crane and rig up of the crane;
operating the crane and perform the lift in a safe manner taking the
signals from the Banks man / Signaller only, unless in an emergency
situation.
EQUIPMENT  Lifting Equipment and lifting accessories shall have a valid third
party certification only as per PR 1708.

Revision:0
 Position the crane as close as possible to the load

 Barricade the location
 Verify the load chart and ensure that the distance between load and
crane are in the safe limit.
 Fix the load to the crane hook using the correct method of rigging
PROCEDURE as per PR depending on the shape of the load
1709 lift planning and  Gradually lift and hold for a while to ensure the stability of load and
execution crane
 If stable execute the lifting operation.
 Ensure that a single banks man is communicating with the operator
 Ensure that the hook is disengaged only after the load is positioned
and secured properly.
10 QUESTIONS FOR A SAFE LIFT
NO DESCRIPTION Yes No
01 Is everyone aware of and do they fully understand the lifting procedures?
02 Has everyone attended the toolbox talk?
Has a pre-use inspection of the Lifting Equipment been carried out and
are the Lifting Accessories tagged or marked with:
03 - Safe Working Load

- A unique identification number
- A valid certification date
04 Are all safety devices working?

05 Does everyone know the lifting supervisor of the lift?
06 Is everyone competent and aware of his or her tasks?
Is there a current Lift Plan and risk assessment and does everybody
07
understand the job and precautions?
Is everyone aware about environmental limits (e.g. maximum permissible

08
wind speed) for the lift?
09 Is the lift area controlled and is the lifting path clear?
10 Are signalling methods and communication agreed and understood?
 Sketch/calculation of lifting plan mentioning load, radius, boom length and capacity of crane.
 Load chart
 Risk assessment*
Attachment  Lifting crew competence cards
 Lifting equipment certificates i.e. cranes and lifting gears.
*For Non routine operation step-by-step instruction with a specific TRA shall be attached.

Revision:
Note: Never start any lifting operation until all concerned have been briefed in a Pre-Start
Meeting, ensuring that they understand their role and responsibilities and that they have signed
onto the Permit-to-Work or record of attendance at the Pre-Start Meeting.
Acknowledgment:
We acknowledge that have verified this method statement against the activities stated in this
statement without any deviation. This method statement will be discussed during the (TBT)
discussion.
Name Signature Date
Lift plan preparer
Lift plan reviewer
Approved by

Revision:0
15.2 Appendix 2, Calculation drawing.
S.NO. Description Unit Value

1 Weight of the lifted load (Load) tones
2 Lifting Beam tones
3 Hook blocks weight tones
4 Lifting Shackles & slings tones
* Total weight tones
S.NO. Description Unit Value

1 Total weight as per above * tones
2 Main boom length m
3 Counter weight tones
4 Radius m
5 Net Capacity of crane tones
6 % of chart capacity used * %

Revision:
15.3 Appendix 3, Hazard and Effects Management Process (HEMP)
 Defective  Injury to personnel 4 C M  Ensure lifting equipment L  Emergency

lifting  Damage to (appliances and accessories) has escape route
equipment equipment valid certification  First aid
 Ensure that lifting accessories are  Emergency
correctly color coded response
 Inspect equipment prior to use
 Ensure equipment is regularly
maintained
 Follow manufacturer’s instructions
 Incorrect  Injury to personnel 4 C M  Riggers, banks men, lifting L  Emergency

use of  Damage to supervisor, crane operator etc. shall escape route
lifting equipment be competent and qualified  First aid
equipment  Emergency
response
 Abrupt  Injury to personnel 4 B M  Load to be lifted/lowered carefully L  Emergency

movements  Damage to  Watch out for objects in the way of escape route
equipment the load  First aid
 Operator to follow the signals of the  Emergency
banks man response
 Unstable,  Injury to personnel 4 C M  Position crane on stable and even L  Emergency

uneven  Damage to ground escape route
ground equipment  Ensure the outriggers are set  First aid
correctly  Emergency
 Use mats under the outriggers to response
distribute ground pressure
 Keep sufficient distance from the
edge of trenches
 Ensure riggers, banks man, lifting
supervisor, crane operator are
qualified

Revision:0
 Improper  Injury to personnel 3 C M  Check suitability of crane position in L  Emergency

handling of  Damage to relation to radius, boom length and escape route
load equipment load chart  First aid
 Make sure load down area is safe  Emergency
 In case of loading a vehicle ensure response
its position is suitable
 Ensure correct and certified rigging
is used
 Use tag lines to avoid swinging of
the load
 Lift the load carefully 10-20cm
before proceeding
 Ensure riggers, banks man, lifting
supervisor, crane operator are
qualified/certified
 Ensure crane operator will follow
signals of banks man
 Direct supervision
 Suspended  Injury to personnel 4 C M  Personnel never to be allowed L  Emergency

load / fatality under suspended load or within escape route
 Damage to swinging radius  First aid
equipment  No tools, food or drinks to be  Emergency
allowed near moving crane parts response
 Use tag lines to avoid swinging of
the load
 Cordon off area
 Restrict area to and limit number of
authorized persons
 Crane operator shall not leave
controls unattended
 Never leave load unattended
 Overloadin  Injury to personnel 4 C M  Ensure correct capacity crane is L  Emergency

g crane / fatality selected escape route
 Damage to  Ensure load computer is working  First aid
equipment correctly  Emergency
 Ensure load charts and boom angle response
indicator are available
 SWL, inspection and next due date
are displayed prominently on the
boom
 Load only to be lifted vertically
 Load not to be dragged
 Crane not to be operated on a slope
 Do not lift loads with unknown
weight and centre of gravity
 Use correct and certified rigging
(correct color coding)
 Do not override (load) safety
devices
 Inspect equipment prior to use
 Strictly adhere to lift plan

Revision:
 Inadequate  Injury to personnel 4 C M  Plan the work to avoid congestion L  Emergency

work space / fatality and conflicting tasks in that area escape route
/  Damage to  Ensure adequate space is available  First aid
Congested equipment to work and manoeuvre crane and  Emergency
area vehicle response
 Parking not to be allowed in the
area
 Provide proper storage area
 Maintain good house keeping
 Use only qualified/certified riggers,
banks man, lifting supervisor, crane
operator
 Insufficient  Injury to personnel 4 C M  Use only qualified/certified riggers, L  Emergency

communica / fatality banks man, lifting supervisor, crane escape route
tion  Damage to operator  First aid
equipment  Ensure it is clear who is the lifting  Emergency
supervisor response
 Ensure banks man is easily
recognized by wearing a colored
vest
 Ensure banks man signals are
understood and followed
 Restrict area to and limit number of
authorized persons
 Bad  Injury to personnel 3 C M  Follow strictly crane manufacturers L  Emergency

weather  Damage to requirements for wind speed escape route
equipment  Stop work  First aid
 Emergency
response


Petroleum Development Oman L.L.C.: Specification For Lift Planning and Execution

Uploaded by

Copyright:

Available Formats

Petroleum Development Oman L.L.C.: Specification For Lift Planning and Execution

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Petroleum Development Oman L.L.C.: Specification For Lift Planning and Execution

Uploaded by

Copyright:

Available Formats

Petroleum Development Oman L.L.C.

Specification for Lift Planning and Execution

Document Type Specification

Issue Date Feb 2018

This page was intentionally left blank

Printed 12/02/2018 Specification Page 2

Printed 12/02/2018 Specification Page 3

Version No. Date Author Scope / Remarks

iii Related Business Processes

iv Related Corporate Management System (CMS) Documents

Design: CP-117 Project engineering

Printed 12/02/2018 Specification Page 4

Printed 12/02/2018 Specification Page 5

Printed 12/02/2018 Specification Page 6

1.2 Changes to the Specification

Printed 12/02/2018 Specification Page 7

3 Role and Responsibilities

3.1 Operation Managers (Company)

3.2 Appointed Person

3.3 Lifting Supervisor

Persons who have been authorized to supervise lifting operations shall:

understanding of all those involved in the task.

3.5 Slinger and Signaller / Rigger and banks man

Printed 12/02/2018 Specification Page 9

3.6 Executing party

 To identify lifting parameters needed to execute the work.

3.7 Lifting Equipment Controller

Printed 12/02/2018 Specification Page 10

5.4 The load

6 Lift Planning and Execution

6.1.1 Risk Assessment

6.1.2 Lift Plan

6.2 Categorizing Lifting Operations

Printed 12/02/2018 Specification Page 11

6.2.1 Routine Lifts - low rate

6.2.2 Non-Routine Lifts

6.2.3 Non-Routine simple lift – Medium Rate:

6.2.4 Non-Routine complex lift – High Rate:

Printed 12/02/2018 Specification Page 12

6.3.1 Communication of Lift Plan

Printed 12/02/2018 Specification Page 13

6.3.2 Conducting the Lifting Operation

6.4.1 Man Riding Winches

Printed 12/02/2018 Specification Page 14

 Shall have Slack line prevention system

6.4.3 General requirement

6.4.4 Crane shall be

 Crane shall have valid inspection certificate at least six month.

6.4.5 Crane Operator shall

6.4.6 Passengers being lifted shall

6.4.7 Basket shall be:

6.5 Working platforms (non-integrated) on forklift trucks

Printed 12/02/2018 Specification Page 17

7 Specific Requirements for Execution of Lifting Operations

7.2 Night operations

7.3 Lifting Over Live Plant

Printed 12/02/2018 Specification Page 18

9 Mobile Crane Operations